Training Plan Tile Setting Nc II

Training Materials, tools and equipments for Tile Setting NC II TOOLS QTY. ITEM

EQUIPMENT QTY. ITEM

MATERIALS QTY. ITEM Glazed wall tiles (20 25 boxes cm x 20 cm) Vitrified floor tiles (20 25 boxes cm x 20 cm) Mosaic tiles (12” x 150 pcs. 12”)

5 pcs.

Notched trowel

2 pcs.

Angle grinder

2 pcs.

Tile cutter

25 sets

PPE

25 pcs.

Pull- push Rule

5 pcs.

Tile Nipper

15m

Level Hose

5 pcs.

Plumb bob

1 bag

5 pcs.

Spirit level

1 pcs.

5 pcs.

Tri-square (12”)

25 pcs

30 kilos

Tile adhesive Cement Tile plastic spacer Sanding Stone(Carburandum) Pencil

5 pcs.

Rubber squeegee

25 pcs.

5 pcs.

Rubber mallet

10 pcs.

10 pcs

Pointing trowel

5 rolls 1 roll

Tile grout (match with the tiles) Foam Tile trim(color match with wall tiles) Nylon string # 50 Nylon string # 12

1 kilo

Cotton rags

5 pcs.

Water pail assorted 3”and 4” Concrete Nail 1” CWN

5 kilos

5 pcs

Diamond Cutting Disc Cold Chisel

5 pcs

Claw Hammer

2 pcs

½ kls 1/4kls

NOTE: The number of cement or adhesive and tiles and its sizes (for floor and wall tile) will depend on the actual number needed for the target output plus the tiles needed for assessment. PPE includes: 1. Hand gloves ( rubber) ung ginagamit pagnaglalaba 2. Goggles 3. Hard hat ( if available) 4. Dust Mask

Trainees’ Training Requirements Basic Competency

Training Activity/Task

TRAINING PLAN Qualification: TILE SETTING NC II Nominal Duration: 82hrs Facilities/To Mode of Staff/Person ols and Training Concerned Equipment

Venue

Assessment Method

Date and Time 18hr s

Common Competency

24hr s

CORE COMPETENCY

40hr s

1. LAY AND REPAIR WALL AND FLOOR TILES

32 hrs

1.1 Plan and 1.1 Secured and prepare for interpreted Work work instruction in line with job requirements

1.2 Identified Safety and quality requirements in line with Occupational Safety and Health Standards (OSHS) and company standard operating procedures

Self-pace Individualize training method Group Structured training method

Trainer (Efren G. Gayanes) Trainees

Module on blue print reading; CBLM; PPT, Blue Print

Contextual Observation learning with oral area/Lear Questioning ning resource area

Self-pace/ Industry immersion Individualize training method


PPT,CBLM, other reference materials/

Contextual learning area workplace On site (constructi on site)

Observation with oral questioning/ demonstration

1.2 Lay out tiling job

1.3 identified Material tiles, tools and equipment in accordance with job requirements

Self-pace/ Industry immersion Individualize training method Group Structured training method


CBLM; PPT; other reference materials/ actual tools and equipment illustration

Contextual learning area

2.1 checked Area(s) to be tiled in line with job requirements

Self-pace Individualize training method Group Structured training method Demonstration Self-pace Individualize training method Group Structured training method Self-pace Individualize training method Group Structured training method


Module on Lay outing CBLM, PPT, Lay outing Tools

Workplace Demonstration area/ On /observation site with oral questioning


Module on Tile laying procedures, CBLM, PPT, Tile laying Tools

Working area/ On site

Demonstration /observation with oral questioning


CBLM, PPT, Tools for mixing



Self-pace Individualize

Trainer (Efren G. Gayanes)

CBLM, PPT, Video clip,

Working area / On

Demonstration /observation

2.2 Laid out Tiles in line with specifications

1.3 Install wall tiles

3.1 Prepared Cement or cement based adhesive according to manufacturer’s instructions or recommendation then applied to tile / wall surface 3.2 Prepared and installed Tiles with

Observation with oral questioning/ demonstration

guide / batterboard set to level alignment

training method Group Structured training method

Trainees

Tools for tile installation

site

with oral questioning

3.3 Checked Horizontal joint for straightness and checked tile edges and surface for alignment



CBLM, PPT, Video clip



3.4 Fixed Tiles to alignment retaining designed pattern to specifications



CBLM, PPT,



3.5 Shown even margins are around openings, frames and fittings, where applicable



CBLM, PPT,



3.6 Installed Special cut tile to create a square corner in accordance with drawings and specifications, where applicable



CBLM, PPT,



1.4 Cut tiles

3.7 Finished Vertical tiles according to plumbness and square corner requirements

Self-pace Individualize training method


CBLM, PPT,



3.8 Maintained All joints straight and uniform in width considering allowance for tolerance of tile



CBLM, PPT,



3.9 Maintained Expansion gaps following specifications 3.10 Polished and cleaned Tiled surface is to Specifications and manufacturer’s recommendations 1.1 Cut Tiles according to required specifications



CBLM, PPT,




CBLM, PPT,


Demonstration /observation with oral questioning Demonstration /observation with oral questioning



CBLM, PPT, Cutting tools


4.2 Cut Recess hole or curve by hand or machine is in required tolerance



CBLM, PPT, Cutting tools


Trainer (Efren G. Gayanes)

CBLM, PPT,

Working area/ On

4.3 Prepared Miter joints, Self-pace retaining glazing on miter Individualize

Demonstration /observation with oral questioning Demonstration /observation with oral questioning Demonstration /observation

1.5 Grout space between tiles

with no chips and uniform in size

training method

Trainees

site


4.4 Prepared Special cut tile in accordance with drawings and specifications, where applicable



CBLM, PPT, working plan



4.5 Jolly-edged Tile to form a miter to prevent the tile body from being exposed at the joint



CBLM, PPT, Tile edging tools



4.6Applied Safety precautions in line with Occupational Safety and Health Standards



CBLM, PPT,



5.1 Cleaned and prepared Joints for grouting following manufacturer's specifications



CBLM, PPT, tile cleaning tools



5.2 Mixed and applied Grout according to manufacturer's specifications



CBLM, PPT, grout mixing tools



5.3 Cleaned and polished Tiles to specifications, removing all dust from surface and joints



CBLM, PPT,





CBLM, PPT,



6.2 Made Adjustments to Self-pace ensure spacing is Individualize uniform training method and pattern and alignment are maintained


CBLM, PPT,


6.3 Finished area with mosaics level to line, if applicable, surface straight and flat and grout are finished to specifications



CBLM, PPT,



7.1 Selected Adhesive based on specifications, tile type and climatic condition



CBLM, PPT,



7.2 Cleaned Surface from residue and protrusions



CBLM, PPT,



1.6 Install 6.1 Fixed Paper-faced or vertical mosaic mesh-backed mosaics to sheets background with tile adhesive

1.7 Lay floor tiles

7.3 Mixed Adhesive following manufacturer's specifications



CBLM, PPT, mixing tools


7.4 Laid Tiles to manufacturer's specifications and expansion gaps maintained between walls and tiles



CBLM, PPT, tile laying tools


7.5 Mixed and applied Grout to clean joints and surface according to manufacturer's specifications



CBLM, PPT, grout application tools





CBLM, PPT, tile cleaning tools





CBLM, PPT,




CBLM, PPT,



7.6 Polished and cleaned Finished tile work according to specifications and manufacturer recommendations 1.8 Tile treads, 8.1 Calculated and risers, steps determined Risers and and steps from concrete steps thresholds / stairs 8.2 Laid out Steps for uniform rise and take even cut on both side


8.3 Placed Step riser packing or render support, where necessary, and installed riser tiles according to alignment



CBLM, PPT,



8.4 Installed Treads in line with the top edge of risers within the required tolerance



CBLM, PPT,



8.5 Applied Grout to wet joints and finished flush with tiles to a smooth finish.



CBLM, PPT,



8.6 Cleaned and polished finished tile work and free of pitted, chipped, cracked or scratched tile resulting from laying operation



CBLM, PPT,



8.7Polished and cleaned tiled surface is to specifications and manufacturer’s recommendations.



CBLM, PPT,



1.9 Repair damaged tile work

9.1 Performed Damaged tiles removal procedure following established / recommended practices



CBLM, PPT, tile removal tools



9.2 Old bedding is cleaned and cleared for placement of replacement tile



CBLM, PPT,



9.3 Selected and cut replacement tiles, if necessary, following existing pattern and face recommendations.



CBLM, PPT,



9.4 Fitted and installed Tiles to maintain alignment with joints for uniform spacing



CBLM, PPT,



9.5 Performed grouting and cleaned tile face from dirt and other residues



CBLM, PPT,



9.6 Polished and cleaned Tiled surface to specifications and manufacturer’s



CBLM, PPT,



1.10 Clean up

10.1 Cleaned work area as per OSHS requirements



CBLM, PPT,

10.2 Disposed waste and unwanted materials following company standard operating procedure and OSH and environmental requirements


10.3 Stored / stacked unused materials are according to enterprise procedures 10.4 Cleaned and maintained tools and equipment are following manufacturer's specifications



CBLM, PPT,



CBLM, PPT,

Staff/Person Concerned

Facilities/To ols and Equipment

Trainees’ Training Requirements


Trainer (Efren G. Gayanes) Trainees CBLM, PPT,

Mode of Training





Working area/ On site Working area/ On site

Venue

Demonstration /observation with oral questioning Demonstration /observation with oral questioning Assessment Method

2. TILE CORNER 2.1 Plan and prepare for work

1.1Secured and interpreted Work instruction in line with job requirements

Date and Time 4hrs



CBLM, PPT,



1.2.Identified Safety and quality requirements in line with Occupational Safety and Health Standards (OSHS) and company standard operating procedures 1.3 Identified Material tiles, tools and equipment in accordance with job requirements 2.2Tile external corners 2.3 Tile internal corners

2.1 Checked set out tiles for specified tolerance of + - 2 mm based on plumbness and levelness. 2.2 Checked external corners for flatness of surfaces and straightness of intersections. 2.3 Installed tile trim to maintain external returns and tile trim is fitted to both corners.








CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,






2.4 Installed tiles without voids in tile bed and fully bedded to maintain alignment to specifications 2.5 Maintained corners square and finished to specifications. 2.6 Polished and cleaned tiled surface to specifications and manufacturer’s recommendations. 3.1 Checked internal corners for flatness of surfaces and straightness of intersections. 3.2 Fitted and cut Tiles, where required and installed to one wall maintaining alignment to set out and specifications.


Self-pace Individualize training method Self-pace Individualize training method




Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes) Trainees

CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,





3.3 Tiles are fitted and cut, where required and installed abutting adjacent wall tiles to line, set out and specifications. 3.4 Made joints for abutting tiles in accordance with designed margin for grouting or for expansion joint, where applicable to specifications. 3.5 Installed tiles to cove tiles or trim and finished to alignment and specifications. 3.6 Polished and cleaned tiled surface to specifications and manufacturer’s recommendations. 2.4 Clean up

4.1 Cleaned work area as per OSHS requirements

Trainer (Efren G. Gayanes) Trainees Self-pace Individualize training method

CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,








4.2 Disposed waste and unwanted materials of following company standard operating procedure and OSHS requirements 4.3 Stored / stacked unused materials according to enterprise procedures 4.4Cleaned and maintained tools and equipment following manufacturer's specifications

Trainees’ Training Requirements





Mode of Training



CBLM, PPT,



CBLM, PPT,




Staff/Person Concerned

CBLM, PPT,


Facilities/To ols and Equipment

Venue


Assessment Method

3. TILE CURVED SURFACES 3.1 Plan and 1.1Secured and prepare for interpreted Work work instruction in line with job requirements

Date and Time 4hrs



CBLM, PPT,



1.2.Identified Safety and quality requirements in line with Occupational Safety and Health Standards (OSHS) and company standard operating procedures 1.3 Identified Material tiles, tools and equipment in accordance with job requirements 3.2 Tile curved wall and floor surfaces

2.1 Set out level line around the wall by intermediate marking using leveling equipment. 2.2 Set out location of tiles to determine balanced design and cutting requirements, if necessary.





2.3 Made template to form accurate curve line to tiled surface around the wall.


2.4 Determined method for installing tiles

Self-pace Individualize





Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes)

CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,

Working area/ On

Demonstration /observation

with identification of location of the first tile. 2.5 Prepared cementbased adhesive following manufacturer's specifications. 2.6 Installed guide board to level set out and template curve to specifications. 2.7 Maintained minimum voids in mortar tile beds and tiles are fixed, plumb (wall), and flush. 2.8 Laid floor tiles to set out grid with perimeter tiles marked and cut to fit curve wall. 2.9 Mixed tile grout with water and applied to joints according to specifications, to provide flush and smooth finish.

training method





Trainees Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes) Trainees


site


CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,




2.10 Polished and cleaned tiled surface to specifications and manufacturer’s recommendations. 3.3 Tile circular volume, wall and arches

3.1 Set out, cut, positioned and checked template to maintain conformity to tile surface for curve. 3.2 Positioned and installed guide board to line to maintain uniform spacing. 3.3 Marked and cut tiles, where applicable, installed into place to specifications. 3.4 Installed tiles on walls and plumb, maintaining levels and curvature of wall to specifications. 3.5 Installed tiles to archways, maintaining line and curvature to specifications.


Self-pace Individualize training method Self-pace Individualize training method Self-pace Individualize training method Self-pace Individualize training method




Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes) Trainees


CBLM, PPT,



CBLM, PPT,



CBLM, PPT,


CBLM, PPT,


CBLM, PPT,



CBLM, PPT,




3.6 Mixed tile grout with water and applied to joints of tiled surfaces and tiled surface is finished to specifications. 3.7 Polished and cleaned tiled surface to specifications and manufacturer’s recommendations. 3.4 Install 4.1 Checked Surface mosaic tiles on from protrusions and a circular from plastering column imperfections. 4.2 Prepared Template for column tiling diameter to specifications. 4.3 Applied mortar evenly to the required tiling diameter thickness and finished to curve based on prepared template specifications.







CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,




4.4 Positioned and installed guide board to maintain level line.

3.5 Clean up

4.5 Mosaic tiles are installed to column maintaining even spacing and level finish to specifications. 4.6 Mixed tile grout with water and applied to tiled surface and tile surface is finished to specifications. 4.7 Polished and cleaned tiled surface to specifications and manufacturer’s recommendations 5.1 Cleaned work area as per OSHS requirements 5.2 Disposed waste and unwanted materials of following company standard operating procedure and OSHS requirements



Self-pace Individualize training method Self-pace Individualize training method Self-pace Individualize training method



Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes) Trainees Trainer (Efren G. Gayanes) Trainees

CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,



CBLM, PPT,




5.3 Stored / stacked unused materials according to enterprise procedures 5.4Cleaned and maintained tools and equipment following manufacturer's specifications





CBLM, PPT,



CBLM, PPT,



Conformed: Training Supervisor

EFREN G. GAYANES Trainer

Training Plan Tile Setting Nc II

Recommend Documents