Error Code Canon iR 4570 & iR 3045 Tuesday, June 16, 2015 ARAHMAN FOTOCOPY 0 Product :imageRUNNER 4570 series Title : E000 Error : There were several symptoms 1st symptom was an intermittent error code of E000, sometimes the machine would run as many as 20k before the problem would re-occur. 2nd symptom was the fixing film could be caked with toner. 3rd and most common symptom was that the latch would catch when opening the Main Right Side Door, this can be remedied by adjusting the cover that can interfere with the fuser release (1 screw ) (this cover is added when installing the internal finisher). The common mistake in the field is to bend this latch instead of adjusting the cover. Workaround : Problem was that the latch that releases and applies pressure to the fixing film had been bent causing this mechanism to work erratically (proper and improper pressure when the Main Right side door was closed ). Solution was to replace the latch which is formally f ormally called the Hook Holder Unit; Part # FM2-0355-000 Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E001 Error Code That is Not Resetable Error : When the machine powers up the E001 E001 error code is displayed but cannot be reset. (Note: The reset procedure for an E001 code is COPIER>FUNCTION>CLEAR>ERR) Workaround : In this case, the Main Power Supply PCB Assembly was replaced. The machine was powered up and the E001 code was able to be reset. The part number for the Main Power Supply Supply Assembly is FM2-0260-000. Remember, if the fixing unit circuitry has an open or a short, the code may not reset. Be sure to confirm the fixing unit wiring and try resetting the code before replacing the Main Power Supply Assembly
Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E004 Error Code Problem : The imageRUNNER 2270 / 2870 / 3570 / 4570 displays an E004 code. Replacement of the fuser assembly and clearing of the error code in service mode resolves the issue. After approx. one day of operation the E004 code returns. Inspection of the fuser reveals that the ceramic heater element has cracked into two or more pieces with apparent arcing from the heater element. Solution : To resolve this reoccuring error code it is necessary to cut all the wire ties on the wire harness running from the fuser assembly to the DC-CON PCB and Power Supply. Product :imageRUNNER 2230/2230G/2270/2830/2870/30 2230/2230G/2270/2830/2870/3025/3030/3035/30 25/3030/3035/3045/3530/3530G/357 45/3530/3530G/3570/4570 0/4570 Title : E014-0001
Error : E014-0001 was indicated upon start-up or when pressing the Start button. E014-0001 can be an indication of a faulty fixing motor. E014-0001 can be displayed when the drive detection signal is absent for 2 sec although detection is executed every 100msec after the start of motor rotation.
Workaround : 1. Check the fixing unit for binds or broken parts. 2. Re-fit J311, and J319 connectors of the DC Controller PCB. 3. Re-fit J1009 and J1011 connectors of the fixing motor. 4. If the symptom still occurs, replace the fixing motor with a new one. The part number for the Fixing Motor is FK2-0367-000. Product : imageRUNNER 2270 / 2870 Title : E020 Error Code Problem : E020 when copying. The sub-hopper motor M12 would not turn on in service mode or when running copies. As a result, the developing assembly would run out of toner. Tried replacing the Hopper Assembl y, Developing Assembly and DC Controller with no change. Solution : Replace the Controller Power Supply PCB. This PCB provides 3.3v, 5v, 13v and 24v to the DC Controller. The part number is FM2-2764-000. It is item 15, shown below, and is located behind the Accessories Power Supply. Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Title :E020-0000 Error : The E020-0000 Error Code will occur if there is an absence of toner detected by the Developing Assembly Toner Level Sensor and a presence of toner is detected by the Hopper Toner Level Sensor. The error code will be displayed after a specified period of time with the sensors detecting this condition. Workaround : The output of the sensors can be checked at the DC Controller PCB. In this case, the sensors output indicated toner in all areas of the developing assembly. The DC Controller was replaced and resolved the E020-0000 Error Code. Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E020-0000 Error Code Error : E020-0000 Error Code will occur if there is an absence of toner det ected by the Developing Assembly Toner Level Sensor and a presence of toner is detected by the Hopper Toner Level Sensor. Workaround : In this case, a small piece of plastic from the toner bottle was found lodged in the developer unit auger. With the auger blocked, the toner would not properly move to the sub hopper. The plastic piece was removed and the toner in the developer unit was vacuumed out to prevent further contamination. Inspection of the toner motor drive and the auger mechanism for any foreign object damage is recommended before installing a new toner bottle. Product : iR 4570 series Title : E024 Error : E024-0001 Error Code: The toner level sensor has an open-circuit or is not connected.
Workaround : E024-0001 Error Code: Toner gets in the developing assembly toner sensor (TS1) and may be shorting out the sensor. Bl ow out any toner in the sensor wiring and check to see if measure resolved the symptom. The toner level sensor has an open-circuit, replace the toner sensor. Toner Sensor FK2-0358 However, re-attachment of the sensor also solves the symptom. When the symptom has occurred, make the following selections in se rvice mode [ COPIER > I/O > DCCON] and check the setting for the bit1 of [P021]. If the setting is "1", re-attach the toner sensor. Product :imageRUNNER 2230 / 2230G / 2270 / 2830 / 3025 / 3030 / 3035 / 3045 / 3530 / 3530G / 3570 / 4570, Finisher S-1 Title : E024 on an imageRUNNER 2230/2270/3025 series machine. Error : E024 on an imageRUNNER 2230/2270/3025 series machine. Workaround : One problem found has been the toner sensor scraper blade in the developer not making contact with the surface of the toner sensor. To check the toner sensor scraper blade first set up a work area. Lay out several sheets of 11 x17 paper on the work surface. Disassembling the developer is a messy job. Remove the upper cover of the developer and then rotate the developer in a counter clock wise direction. Basically the cylinder should rotate so the toner is scraped off of the cylinder by the developer blade. If it is rotated in the wrong direction a large amount of toner will adhere to the developer cylinder and makes a mess. The toner sensor is located on the on the outside of the developer and part of it goes through the wall of the developer unit. Product : imageRUNNER 2230/2270/2830/3870/3530/3570/4570 Title : Error E064-0002 Error : E064-0002 The machine displays an E064-0002. The machine creates solid black copies/internal tes t prints from edge to edge without any blanking. Workaround : Check the physical connections of the primary contacts. The primary drum contact is located on the drum and makes contact with an HVT metal contact on the ma chine's rear. The drum's primary contact tab can be easily bent or deformed during drum replacement or removal. If it becomes bent it can cause solid black copies creating a voltage leak also causing an E064-0002. Before replacing the high voltage power supply check the contact tabs first. Reshape the contacts or replace the drum. Product : imageRUNNER 2230 / 2230G / 2270 / 2830 / 2870 / 3530 / 3025 / 3030 / 3035 / 3045 / 3530G / 3570 / 4570 Title : Error E064-0003 Error : E064-0003 Workaround : The E064 code with a 0003 sub code can occur if Toner gets on the Developing Bias Tab. If the Toner is getting on the Developing Bias Tab you should check the seal on top of the Developer. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E100 - 0001 and E110 - 0002 Problem :
The machine is displaying error code E100 sub code 0001 and E110 sub code 0002. The E100 - 0001 indicates that the BD interval is outside a specified range. The E110 -0002 indicates that the scanner motor of the laser is faulty. The laser unit and DC controller were replaced. The wiring for the laser unit was checked. Solution : The problem was that the grounding spring for the steel registration r oller was not making contact with the roller. Reformed the spring so that it made contact with the roller and the error code issue was resolved. Please see the photo below. The grounding spring is circled in red. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E100 or E110 is Shown on the Display Error : E100 or E110 is shown on the Display. The error points to a Laser or Laser Shutter iss ue. After inspecting all Laser related item it was found that the Ground Plate for the Registrati on Roller was not making contact. Workaround : Check that the ground tabs are touching the Metal Registration Roller correctly imageRUNNER 2230 / 2830 / 3530 Title : E100, E110 Error Codes Error :E100, E110 Workaround : Although the Main Power Supply, Controller Power Supply, DC Controller, Laser, and Drum, were replaced for this issue, the Accessories Power Supply Pcb. resolved the problem (Part number FK2-0338-000). Product : imageRUNNER 2270/ 2870 / 3570 / 4570 Title : E100-0001 Error Code Problem : The machine is displaying an E100-0001. Cleared RCON, DCON and MMI. Cut tie-wraps. The DC Controller, Laser Assembly, Main Controller, Hard Drive, Memory, Boot ROM, All Night Power Supply, Controller Power Supply and wiring harnesses to the laser were replaced with no change. Checked the laser shutter. Solution : When the DC Controller was replaced, the original DCON ROM was reused. Flashed the DCON firmware and resolved the problem. Product : imageRUNNER 3025 / 3035 / 3045 Title : E110-0001 / 0002 IntermittentProblem : Very intermittent E110-0001 / 0002, on copies 1 code in about 150 copies. The DC Controller, Laser, Power Supply and Main Controller have been replaced with no change in error code. Solution : While in process of replacing 2nd Laser ass yembly, found a cut on two wires in harness to Laser causing a short circuit. Harness was repaired with electrical tape. Product : imageRUNNER 2230 / 2830 / 3530 Title : E111 Error Code when Flashing the Machine Problem : When trying to flash the machine, the service support tool displays an E111 error. There is also a messa ge that says "Necessary data not found bpchost.cha files \ servicesupporttool \ bpchost.cha". Solution : Multiple versions of the service support tool were i nstalled on the laptop. It is important to uninstall previous versions of the service support tool before installing a new verison of the tool.
Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3530 / 3570 / 4570 Title :E190 and E240 Error Codes in Service Support Tool when trying to Format HDD Problem : After replacing the HDD, the Service Support Tool is alte rnately displaying E190 and E240 error codes. Solution : After reseating connections on the Main Controller, it was discovered the contacts on the Boot Rom were dirty. After cleaning the contacts on the Boot, as well as the socket on the Main Controller, the HDD was able to be formatted, and all files installed. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E191 Problem : The machine was giving an error code of E191 which indicates an error with communication with the highvoltage power supply. Replaced the high-voltage power supply and the DC controller pcb with no change. Solution : The wiring between the DC controller and the high-voltage power supply was broken. Replace the high voltage connect cable. Part number FM2-2819-000. The cable is item 9 circled below. Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Title :E191 Error Code Error :E191 Error Code
Workaround : Check for a pinched wire in the harness from Connector J404 of the High Voltage Power Supply PCB to the rear frame connector of the ImageRunner, J4001. It may be necessary to replace the High Voltage Power Supply PCB (part number: FM2-0261-000). Please note: currently, there is no part number for the affected wiring harness Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E225 Occurs During the Power Up Sequence Problem :E225 Occurs During the Power Up Sequence Solution : In this case, the platen glass had been reversed when being cleaned by the technician. Make sure the platen glass has the red arrow in the rear left corner of the machine top plate. As indicated in the picture below, the red arrow should be right above the CIS ribbon cable when the glass is installed correctly. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E227-0001 Problem :E227-0001 & all 24 volts are missing in machine.
Solution : E227-0001 was caused by Main Power Supply not putting out correct voltage at J1303. After installing new Main Power Supply {FM2-0260-000} machine worked with no problems. Product : imageRUNNER 2230 / 2230G / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3530G / 3570 / 4570 Title : E240 Error only on Duplexing. Error :E240 Error only on Duplexing. The imagerRUNNER will also lock up when the code occurs.Simplex copying works fine. Workaround :
In this case CL6, Duplex Clutch was faulty. You can check the Duplex Clutch in Service mo de in Parts check, CL > 4. Product : imageRUNNER 3025 / 3030 / 3035 / 3045 Title : E261-0000 Error Code Problem : The Service Manual notes this issue as the Zero-Cross signal not detected for 500msc or more after the relay is on. Solution : In this case, by replacing the Main Power Supply Assembly ( FM2-0260-000 ) corrected the iss ue. Product : imageRUNNER 3025 / 3030 / 3035 / 3045 Title : E261-0000 Error Code Problem : The Service Manual notes this issue as the Zero-Cross signal not detected for 500msc or more after the relay is on. Solution : In this case, by replacing the Main Power Supply Assembly ( FM2-0260-000 ) corrected the iss ue. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E291 - Network Connection Problems Problem : When trying to update the system software the laptop displayed the following message in the Service Support Tool interface. E291 Check if the PC is connected to the network. Socket Error Number:10065 Socket Error Description: No route to host. File Name: Target Info.txt
Solution : The laptop could ping the imageRUNNER and yet the E291 code would display when trying to download the system software. In this case, the main controller clear was performed. (COPIER>FUNCTION>CLEAR>MN-CON) Then, a successful system software update was able to be completed. Note: When performing an MN-CON clear you should first generate a p-print. (COPIER>FUNCTION>MISC-P>P-PRINT) Upon completion of the MN-CON clear, re-enter the service mode contents listed on the p-print. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E292 - Service Support Tool Error Error :When attempting to download system software, the laptop displays an E292 code. Workaround : The connection to the imageRUNNER was confirmed using the ping command. In this case, the tech had registered only "English" language into the Service Support Tool. When additionally registering the "Japanese" language in the Service Support Tool, the imageRUNNER took the download without getting the E292 code. Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title :
E400-0002 on the Display Error :The error code E400-0002 is shown on the display when trying to make copies. Workaround : The solution in this case was to reseat the Document Feeder-N1 interface cable AND clear RCON. *Note* The feeder width adjustment must be done after clearing RCON. Product : imageRUNNER 2270 / 2870 / 3570 / 4570Finisher-Q1 / Q3 Saddle Fnisher Q2 / Q4 Title : E505 Error Code Problem :E505 is defined as a Backup Ram error.The Finisher Controller had just been replaced in response to a different error code. When attempting to adjust the Alignment Position, the Alignment Plates will not move into position. Solution : When replacing the Finisher Controller the following adjustments must be made: 1. Alignment Position 2. Staple Position It was discovered that the Finisher Front Cover Switch (MS31 ) was not being actuated. Without proper activation of MS31the necessary adjustments cannot be made. After activating the Front Cover Switch The adjustments were performed, and the problem was solved. Product : imageRUNNER 2230/2830/3530 Title : E508 Error :E508 is displayed on the control panel after install ing a Q1 or Q3 finisher. Workaround : The only Finisher that the imageRUNNERs 2230/2830/3530 support is the Finisher S-1. This error code of E508 is not found in the Service Manual but happens when either the Finisher Q1 or Q3 are installed on these "30" series machines. The "30" series machines do not support the Finisher Q1 or Q3. Product : imageRUNNER 2270 imageRUNNER 2870 imageRUNNER 3570 imageRUNNER 4570 imageRUNNER 2230 imageRUNNER 2830 imageRUNNER 3530 Title : E520 sub code 8001 Error :The pick up roller will move towards the rear and start to vibrate, then the E520 is generated with the sub code 8001. Workaround : Replacing the offset motor resolved the E520 - 8001. M4 Offset Motor Part number 4K1-4053-000 Product : Finisher-T1 / Saddle Finisher-T2 / Finisher-AD1 / Saddle Finisher-AD2 / Finisher-AE1 / Saddle Finisher-AE2 / Finisher-Q3 / Saddle Finisher-Q4 / Finisher-AA1 / Saddle Finisher-AA2 / Finisher-R1 / Saddle Finisher-R2 / Finisher-Q1 / Saddle Finisher-Q2 / Finisher-Y1 / Saddle Finisher-Y2 / Finisher-N1 / Saddle Finisher-N2 / Finisher-W1 / Saddle Finisher-W2 / Finisher-H1 / Saddle Finisher-H2 / Finisher-AC1 / Saddle Finisher-AC2 / Staple Finisher-C1 / Booklet Finisher-C1 / Staple Finisher-B1 / Booklet Finisher-B1 / Staple Finisher-E1 / Booklet Finisher-E1 Title : E531 with sub code 0001 / 0002 Error : The E531 error code indicates an issue with the stapler motor or stapler home position detection sensor. In this occurrence of the E531, the stapler will drive to the rear staple position, paper will accumulate in the operation tray and generate the E531 at the time of staple. Staple assembly, staple harness ribbon cable and
the finisher controller were replaced, the finisher continued to error with the E531. Workaround : It was found that MSW104, staple safety switch was not properly actuated. The spring on the white actuator was missing. This switch cuts 24v to the stapler motor M11 and is actuated when the swing guide is forced in the maximum open position. A quick way to check MSW104 is from the finisher controller at J714 pins 1 & 2. Pin 1 should read 24v constant and pin 2 will read 24v when MSW104 is actuated, and 0v when MSW104 is opened. If pin 1 reads 24v and pin 2 reads 0v whether MSW104 is actuated or open, replace MSW104. MSW104 part number is FH7-6379-000 Note: Due to the range of Finishers covered in this Knowledge Base article, the safety switch maybe addressed by a different identification number. Please check the related Service Manuals & Parts Catalog for correct identificationProduct : imageRUNNER 2270 series, S1 Finisher Title : E540Error : Error code E540. Dealer had replaced the tray harnesses and the finisher controller pcb with no change in symptom. Workaround : Solution was to replace the Finisher Controller FG1-1478-060 and the Stack Tray Motor (M1) 4K1-4055000 as M1 was shorted out and causing the Finisher Controller to fail Product : imageRUNNER 2270 / 2870 / 3570 / 4570, S1 Finisher Title : E540 0001 Error :E540 error code with a sub code of 0001 is not listed in the service manual. Workaround : If this code is displayed and the bin will not lower: Check PI 10, tray lower limit sensor operation. If defective replace the sensor. Part # W68-5571-000 Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E540 sub code 8005 Problem : The machine is giving an E540 error code with a sub code of 8005. This sub code is not listed in the service manual. The error code corrections are listed in tech pub TP06 238. The delivery tray will drive all the way to the top and then the error code will be displayed. Solution : Check FU3 on the upper left corner of the finisher controller. If it checks out good, power the machine off and lower the finisher delivery tray by hand and power the machine back on. If the fuse is blown, replace the finisher controller. Part number 4G1-1478-050 Product : imageRUNNER 2230 / 2270 / 2870 / 3530 / 3570 / 4570, S1 finisher, B1 tr ay Title : E542 Error : An intermittent error code of E542 and sometimes E584 was present. Workaround : The solution to remedy both intermittent codes was to replace the B1 harness part number 4G1-2262-000 Product : imageRUNNER 2230 / 2230G / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3530G / 3570 / 4570
Title : E542 Sub Code 8004. Error : E542-8004 code occurs when tray B continues to drive down and binds up causing a clicking noise before the code appears. Workaround : In this particular case the option tray escape position sensor PI14 was faulty. Replacing PI14 part number WG8-5571-000 resolved the problem. Product : imageRunner 2230 / 2230G / 2270 / 2830 / 2870 / 3530 / 3530G / 3570 / 4570 imageRunner C3100 / C3170 Finisher S1 Title : E584 Codes Problem : If the Optional Bin B1 is installed, various Error Codes ma y result if the Finishers cover screws are not all installed and fully tightened Solution : The covers on the Finisher S1 and P1 are an important part of the Finisher frame, if all the cover screws are not installed and tightened the frame will flex excessively. The most common problem when the optional Tray- B1 is installed is that the shutter will intermittently contact the upper or lower bin resulting in a loud noise and / or E584 Codes. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Finisher Q3 Punch Unit R1 Title : E593-8002 Error : E593-8002 Workaround : In this case it was found that there was packing material left in the Punch Unit R1 during a new install. Upon the removal of the packing material the Punch Unit was able to move freely and the error code was resolved. Product : imageRUNNER 3025 / 3030 / 3035 / 3045 Title : E602 - 0105 Problem : The machine is displaying an error code of E602 with a sub code of 0105. This sub code is not found in the service manual. Typically, an E602 indicates and error with the hard drive. Solution : Replaced the SDRAM on the Main Controller and the issue was resolved. Part number WA7-4625-000. Product : ImageRUNNER 2230/2230G/2270/2830/2870/3530/3025/3030/3035/3045/3530G/3570/4570 Title : E602-0105 Problem : Error code E602-0105, replacement of the Hard Drive, reloading SSW and reformatting Hard Drive does not resolve the error code. Solution : The Hard Drive was corrupt and was corrupting the main controller and would corrupt any new Hard Drive that was replaced into the machine and if that Hard Drive was tested into another machine it took out that Main Controller also. To resolve this issue the Hard Drive and the Main Controller had to be replaced as a set, format the HDD and load SSW. Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Title :E610 Error Code Error : E610 Workaround : The E610 error code is generally associated to an imageRUNNER equipped with a security kit. The security kit is LMS activated, but also contains an Expansion Bus Board and a USB Application Interface Board which connects to the main controller. If the Expansion Bus Board or USB Application Interface Board is
removed or has a loose connection to the main controller, an E610 error code ma y be generated. Reset and / or reinstall the Expansion Board and the USB Application Interface Board to resolve the E610 code. Product : imageRUNNER 3030/3035/3045 Title : E611-0000 is on the display Error : E611-0000 is on the display. The code usually would happen sporadically. Workaround : In this case, clearing sectors of the HDD resolved the issue. There have also been some instances where clearing the MNCON has also resolved this error code. A definition of this code is not found in the this product series documentation. Below is a description of the code: E611-0000 Error in repeat of reboot due to fault of the SRAM, etc. SRAM information has failed, job information stored in the SRAM cannot be read and a reboot is repeated at recovery from powering off Product : imageRUNNER 2230/2270/2830/2870/ 3530 /3570/ 4570 Title : E674-0008 Error : Although the error code of E674 is documented in the Service Manual, the sub code of 0008 is not. In this case, the machine was displaying an E674-0008. The Service Manual describes that an E674 is related to a communication fault between the multi line fax pcb and the Main Controller pcb. When looking in Service Mode>Copier>Display>Version>Fax, the machine displayed, a "??#" for the version of the f ax. The machine in this case was flashed. Other symptoms experienced were, no dial tone when using the "On-Hook" key using the fax function, the machine could not print any internal/external prints, the machine could not complete the "forced shut down procedure" and would "lock up". Although these symptoms were experienced, the machine was able to copy without problems. Workaround : Following the Service Manual's instructions, the multi line fax pcb assembly was disassembled. Upon inspecting the unit, it was noticed that one of the ribbon cables on the G3 fax control pcb was not seated properly. After reseating the ribbon cables on the G3 fax control pcb, the machine stopped displaying this error code. The fax functionality then returned and the machine stopped exhibiting the other symptoms listed above. Checking and reseating the ribbon cables located on the G3 fax control pcb resolved the is sue. Related Service Manual error code information for an E674 code is: 1. sub code 0001- An attempt to set mode for the fax device has f ailed Remarks for items to check are: 1. Check the connection of the cable between the fax control PCB (2 line) and the main controller PCB. 2. Replace the ROM DIMM of the fax control PCB (2-line). 3. Check ribbon cables within the fax pcb assembly. 4. Replace the fax control PCB (2 line). 5. Replace the main controller PCB. Product : imageRUNNER 2270 / 2870 / 3570 / 4570 imageRUNNER 2230 / 2830 / 3530 Title : E716 error code Error : Error code E716 occurs with the Finisher-S1 is installed. The error code refers to the Cassette Feeding Unit-Y2, which may not be installed. If the Finisher-S1 is disconnected the error code will clear. Workaround :
If the error code E716 is present upon install of a iR XX30 series machine, make sure a 3-Way Unit-A1 is installed. See KB article 54256 for further information. If the error code E716 is generated on a iR XX30 or iR XX70 series unit: Check to see if the error clears when the Finisher-S1 is removed. If the error clears, check for 13VA2 and 24VA going to the 3-way unit-A1. The 13v & 24v is can be checked at J646 of the Accessory Power Supply, pin 1 (13v), pin 3 (24v) to J741 of the 3 way unit-A1, pin 7 (13v), pin 9 (24v). If the voltage is present, replace the 3 way unit-A1 controller. PN: FM2-3221-000. Product : iR4570 series Title : E732 Error : E732-0001 can be displayed when the DDI-S communication error occurs, meaning the communication betwen the Reader and MCON. Workaround : 1. Re-insert the connector J1014 ( reader wire harnes s for DDI communication) on the Main controller PCB. 2. If the symptom still occurs, pull the memory and DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381).Clean the contacts with a clear rubber erasure and reinsert the DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381). 3. If the symptom still occurs, replace the Reader Controller PCB with a new one. FG3-3765-000 = Reader Controller PCB Assemb Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E733 Error Code After Replacing the Boot Rom Error : A new boot rom was inserted into a slot and the machine was turned on. The E733 came up on the display after a few minutes. Workaround : In this case, the boot rom was mistakenly placed in the slot located on the DC Controller. The Boot Rom slot on the Main Controller is the same size as the DCON Dimm slot on the DC Controller. Hastily replacing this chip without confirming the correct slot will damage the chip. NOTE: If you are installing a network boot rom and it is damaged, you will need to contact the TSC for the replacement procedure. Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Finisher-S1 Title : E733-0001 Error Code Error : The imageRUNNER is displaying an error code of E733-0001. The code is consistent, and will occur when an attempting to make a copy. After the start key is pressed, the paper will feed to the registration roller, and the imageRUNNER will go into code. Workaround : An E733-0001 indicates a communication problem, usually between the DC and Main Controller. In this example the problem was rectified by replacement of the Finisher Controller. A possible scenario, would be to disconnect the finisher to observe a change in s ymptom. If the imageRUNNER will output paper, or at least feed paper past the previous point, the problem may lie in the finisher. S1-Finisher Controller P/N - 4G1-1478-060 Product : imageRUNNER 2230 / 2830 / 3530 / 4530 Title : E744-1000 Problem : While flashing machine, power in office shut off while writing to Boot-rom. After rebooting machine, could not write software to Boot-rom. Solution :
Boot-rom software was damaged during power failure. Part number for Boot-rom is FM2-3803-600.Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E749Error : E749 in Error History. Workaround : An E749 is in the error history after installing / uninstalling a Printer Kit or MEAP device in the i R2270, 2870, 3570, 4570. This error only occurs once when this type of installation has been done.This error may only be displayed in history and not on the LCD Display.Cycle the power of the machine after installation of these options. Product : imageRUNNER 2230 / 2270 /2830 / 2870 / 3530 / 3025 / 3030 / 3035 / 3045 / 3570 / 4570 / 3225 / 3230 / 3235 / 3245 Title : E805 Error : E805 Workaround : It has been found that the exhaust fan can become dirty or locked up. Clean the fan and make sure the fan blades spin freely. In some cases the fan needs to be replaced. Fan part number is (FK2-0360-000) for both fans. Labels: canon imagerunner error codes IR 3035 * 3045 * 3530 * 3530G * 3570 * 4570 2525 * 2530 * 2535 * 2535i * 2545 * 2545i canon copier canon error codes e602 e540 e001 e000 e732 copiers copy machine canon imagerunner error codes IR 3035 * 3045 * 3530 Canon Copie
Error codes for Canon IR canon imagerunner 330 400 ir210 gp210 gp200 ir200 ir 330 ir330 ir 400 canon copier canon copy machine
"E000"Fixing temperature fails to rise "E001"Fixing temperature rises abnormally "E002"Fixing temperature fails to reach a specific value "E003"Fixing temperature drops abnormally "E007"Fixing film has become displaced "E010"The main motor fails to lock "E030"Total counter failure "E031"Option counter failure "E032"The copy data controller counter is faulty "E051"The horizontal registration home position detection mechanism fails "E064"The high voltage (primary charging, transfer char ging, developing) output is faulty "E100"BD Error "E110"The laser scanner motor fails to lock "E190"RAM error "E191"Communication error between the DC controller & composite power supply "E202"Scanner home position cannot be detected "E220"Scanning lamp fault "E240"Communication error in the DC controller "E243"Communication error between control panel & image processor PCB "E261"Error in the zero cross signal "E301"Intensity of scanning lamp is not correctly adjusted "E400"Communication error between copier and RDF-G1 "E401"Pick up error in RDF-G1 "E402"Belt drive fault in RDF-G1
"E403"Feeder fault in RDF-G1 "E411"Original tray paper sensor/ registration sensor in RDF-G1 "E422"Communication error between copier and ADF-F1 "E710"Error in IPC communication "E711"Error in IPC communication "E712"Error in communication with the feeder "E713"An IC error has occured (sorter) "E716"Communication error with the pedestal "E717"Communication error with the copy data controller "E803"Error in the output voltage of the composite power supply PCB "E901"Pedestal motor or controller PCB
ERROR CODE COPIER CANON Canon Copier error codes Canon IR imagerunner 2200 2800 3300
1. E000 Fuser problem, Fuser heater, Fuser film, Thermistor, Connections, Power Supply 2. E001 Fuser Temperature too high, Fuser heater, Fuser film, Thermistor, Connections, Power Supply 3. E002 / E003 Low Fuser Temperature, Thermistor, Fuser heater, Fuser film, Connections, Power Supply 4. E004 Fuser problem, triac shorted, thermistor, power supply 5. E007 Fuser film rotation problem ( IR 2200, 2800, 3300 or i ) 6. E009 Fuser does not match power supply or DC controller board 7. E010 Drive problem, main motor, motor drive board, mechanical gear functions 8. E014-0000 Fuser motor ( IR 2200, 2800, 3300 or i ) 9. E019-0000 Waste toner full ( IR 2200, 2800, 3300 or i ) 10. E032-0001 DA unit communications error ( IR 2200, 2800, 3300 or i ) 11. E040 Holding plate drive assembly, holding plate position sensor or holding plate solenoid 12. E043 Paper deck feed motor problem 13. E051-0000 Horizontal registration home detect mechanism ( Motor M9 or sensor PS10 ) ( IR 2200, 14. 2800, 3300 or i ) 15. E054 Duplex feed roller home position sensor lever, duplex feed roller gear, duplex drive board,duplex feed clutch, or duplex motor 16. E055 Horizontal registration guide, home sensor lever, drive gear, duplex drive board, horizontal registration motor or duplex drive motor 17. E064-0000 Charge, transfer or developer bias problem 18. E100 Laser unit, BD mirror, image processor board, laser board, DC controller, can als o happen if drum is not installed 19. E102 Laser problem 20. E110-0000 Laser motor ( IR 2200, 2800, 3300 or i ) 21. E202-0001 Scan problem, scan switch, scan motor, image processor board ( IR 2200, 2800, 3300 or i ), panel locked with error message 22. E203 Scan motor driver board, scan motor or reader controller board 23. E204-0001 ADF lead edge image signal problem ( IR 2200, 2800, 3300 or i ) 24. E211/215 Reader controller board, exposure lamp heater, exposure lamp thermistor, flat cable connections. 25. E216 Exposure lamp, inverter board, reader controller board 26. E217 Exposure lamp heater or heater controller board 27. E219 Exposure lamp, inverter board, reader controller board 28. E220-00001 Exposure lamp inverter board ( IR 2200, 2800, 3300 or i ) 29. E225-0000,-00002 White plate/edge whit plate read error, bad CCD or exposure lamp ( IR 2200, 2800, 3300 or i ) 30. E240-0000 Mcon-Dcon problem, bad DC controller ( IR 2200, 2800, 3300 or i ) 31. E243-0000 Control panel to image processor board communication problem,main controller board
