VGB KKS Code

Guidelines KKS-Identification Sys ystem tem for Powe ow er Stations VGB-B 105 E 7th Edition 01/2010 (Index E)

Published by:

VGB PowerTech e.V. Obtainable Obtainable from:

VGB PowerTech Service GmbH Verlag technisch-wissenschaftlicher Schriften Postbox 10 39 32, 45039 Essen Phone: +49 201 8128-200 Fax: +49 201 8128-329 E-mail: [email protected] ISBN 978-3-86875-329-5

http://www.vgb.org Reproduction only permitted with prior authorisation by VGB.

3 Preface Preface to t he Guidelines, 7th Edition 2010

Since the latest publication of the KKS Guidelines and the key part in the year 2007 the VGB-Working Panel “Reference Designation and Plant Documentation” dealt various applications for amendments respectively specification of the KKS keys. The demand for the applications resulted from new technologies for power plant process, especially for technologies for CO 2-separation und the use of renewable energy sources. In addition the results of experiences in the project management were integrated. Decision was made to implement the results as index “E”. Please see thereto the revision sheet 7, status January 2010.

KKSRules

KKSGuidelines

B 105e

KKS-keys - Function - Equipment unit

Equipment unit and component code reference list

Compendium Establishments between the parties involved in the project“

- Component

KKS Appl Ap pl ic ati on Explanations B 106e

Part A General Application Explanations Part B Engineering disciplinespecific application explanations B1 Mechanical engineering B2 Civil engineering B3 Electrical engineering and control and instrumentation B4 Coding of process control and instrumentation

DIN/KKS Comparison

Part C Engineering discipline-specific identification examples

Part D Type of Power Plant specific KKS Application Explanations

(publication later)

D1 Hydro-Power Plants

This edition corresponds to the German edition 01/2010, index “E”. VGB thanks to the companies involved and the staff members assigned by these with the work. Suggestions and comments to the guidelines and the keys would be appreciated by the VGB-office. Essen, January 2010 ISBN 978-3-86875-329-5

Exclusion of Liability : The VGB-Guidelines and VGB-Instruction sheets are recommendations which may be applicated by everyone. The person using this guideline must however ensure the richt application for each case. They consider the state of technological development at the time of the respective version. No one can be exempted of responsibility for his own actions by using the VGB-Guidelines VGB-Guidelines or VGB-Instruction sheets. This means that everyone acts at his own risk. A liability for VGB PowerTech and for the persons involved in the

4

Preface Preface to t he Guidelines, 6th Edition 2007

Since the latest publication of the KKS Guidelines and the key part in 2003 the VGBWorking Panel “Reference Designation and Plant Documentation” dealt various applications for amendments respectively specification of the KKS keys. Decision was made to implement the results as index “d”. As addition the existing Application Explanations Explanations have been amended amended by the part „KKS Application Explanations for Hydro Hydro Power Plants (VGB-B 106 D1e)“. This edition corresponds to the german edition 06/2007, index “d”. VGB thanks to the companies involved and the staff members assigned by these with the work. Suggestions and comments to the guidelines and the keys would be appreciated by the VGB- office. Essen, August 2007

5

Preface to t he Guidelines, 5th Edition 2003

With the 5th edition 2003 the layout was adapted on the form used by “VGB PowerTech Service GmbH” since the year 2000 and the text of the Guideline B 105 was converted to standardized electronic formats. The VGB Technical Committee “Technical Classification Systems” often specified in the KKS Guidelines, became to the Working Panel “Reference Designation and Plant Documentation” due to the structural changes of VGB in the last years. This Working Panel treated various applications for amendments respectively specifications of the KKS function and equipment unit keys since the publication of the last revision 1995. The met resolutions are mentioned in index “c”, as at October 2003. By thus the German and English editions of the KKS set of rules have the same contents and edition conditions. As addition the existing Application Explanations have been amended by the part „KKS Application Explanations for Hydro Power Plants (VGB-B 106 D1)“. VGB thanks to the companies involved and the co-workers assigned by these the work. Suggestions and/or references to the Guidelines and keys receive the VGB-office gladly. Essen, in January 2004

6

Contents 1

Purpose and Fields of App licati on .................................................................... 8

1.1

Scope of KKS ....................................................................................................... 8

1.2

Requirements on KKS .......................................................................................... 8

1.3

Features of KKS ................................................................................................... 8

2

Format of Code.................................................................................................. 10

2.1

Types of Code and Breakdown Levels ............................................................... 10

2.2

Prefix Symbols and Breakdown Symbols for Types of Code .............................. 11

2.3

Format of Breakdown Levels .............................................................................. 11

2.3.1

Classifying Code Elements.................................................................................. 12

2.3.2

Numbering Code Elements ................................................................................. 13

3

Contents of Data Characters ............................................................................ 14

3.0

Total Plant........................................................................................................... 14

3.1

Process-Related Identification ............................................................................ 15

3.1.1

System Code....................................................................................................... 16

3.1.2

Equipment Unit Code .......................................................................................... 18

3.1.3

Component Code ................................................................................................ 19

3.2

Point of Installation Identification ........................................................................ 21

3.2.1

Installation Unit Code .......................................................................................... 22

3.2.2

Installation Location Code ................................................................................... 23

3.3

Identification of Location ..................................................................................... 24

3.3.1

Structure Code .................................................................................................... 25

3.3.2

Room Code ......................................................................................................... 26

3.3.2.1

Room Identification by Numbering ………………………………………. ………..26

3.3.2.2

Room Identification by Field Raster ……………………………………

4

Notation of Codes ............................................................................................. 29

5

Speci al Rules ..................................................................................................... 30

5.1

Rules to the Keys................................................................................................ 30

5.2

System Codes for Heavy Machinery................................................................... 31

5.3

Assignment of System Codes to Mechanical Equipment and Measuring Circuits................................................................................................................ 31

5.4

Special Rules for Mechanical Engineering.......................................................... 31

5.4.1

Valves ................................................................................................................. 31

5.4.2

Supports.............................................................................................................. 32

5.4.3

Supply Systems................................................................................................... 32

………..27

7 5.5

Special Rules for Civil Engineering..................................................................... 33

5.6

Special Rules for Electrical, Control and Instrumentation Engineering............... 33

5.6.1

Shared Equipment for Electrical, Control and Instrumentation Engineering........ 33

5.6.2

Electrical Equipment ........................................................................................... 34

5.6.3

Control and Instrumentation Equipment.............................................................. 34

5.6.3.1

Measuring Circuits ………………………………………………… ………………..33

5.6.3.2

Closed-Loop Control Circuits ……………………………………. ………………..35

5.6.3.3

Signals and Signal Application …………………………………… ………………..35

6

7

Ap pen di x: Com pendi um of " Est abl ish ments bet ween th e Parties to th e Project" to be made on a Project -Specifi c Basis ........................................... 37 Appendi x: Revis ion sheet

8

1

Purpose and Fields of Appl ication

1.1

Scope of KKS

The Identification System for Power Stations "KKS" serves to identify plants, sections of plants and items of equipment in any type of power station according to task, type and location. It is to be used by all engineering disciplines for planning, licensing, construction, operation and maintenance. The KKS, or sections thereof, can be combined with other identification systems in order to meet additional identification requirements. One particular combination is that with the redundancy code. Redundancy codes result from the need to identify redundancy groups. Redundancy groups are defined in KTA 3501 as combinations of items of equipment in a particular arrangement intended to ensure the independence of redundant items of equipment. The items of equipment within a given redundancy group are identified in keeping with the format for the total plant in accordance with the KKS Guidelines. Referencing of redundancy groups is performed outside the scope of the KKS code with the aid of a separate redundancy code. This is not covered by these guidelines. 1.2

Requir ements on KKS

The following requirements are considered: -

Uniform identification for all types of power station and any connected processes

-

Sufficient capacity and detail for identification of all systems, components and structures

-

Sufficient capacity for extension to accommodate new technologies

-

Consistent identification for planning, licensing, construction, operation, maintenance and waste management

-

Interdisciplinary applicability to mechanical engineering, civil engineering, electrical engineering and control and instrumentation combined with ability to identify according to process functions, points of installation and locations

-

Consideration of national and international standards

-

Non-language-based coding to ensure international usability

-

Application in computer processing

1.3

Featur es of KKS

To fulfil the above-mentioned requirements, KKS has the following features: -

Hierarchically structured format with 4 breakdown levels and fixed alphanumeric data characters

-

Separate identification methods with engineering discipline-specific rules by means of a uniform code format for the three types of identification

9

- Process-related identification - Point of installation identification - Location identification In relation to the identification of plants, systems and items of equipment KKS considers the following standards: Content

DIN

Format of alphanumeric codes, breakdown symbols and electrical component code

40719 Part 2 Edition June 1978

Control and instrumentation equipment, measuring circuits

19227 Part 1 Edition October 1993

IEC

ISO

Publication 750, 1983

Publication 3511-1 1977

DIN = Deutsche Industrie-Norm (German Industrial Standard) IEC = International Electrotechnical Commission ISO = International Organisation for Standardisation

The KKS Guidelines do no t cont ain rules on:

-

Combination of the code with other identification systems

-

Methods of marking, e.g. in control rooms, local control stations, labelling of components and identification in and of documents

-

Open text abbreviations

-

Identification of redundancies.

10

2

Format of Code

2.1

Types of Code and Breakdown Levels

In consideration of the various requirements placed on the identification of plants, sections of plants and items of equipment in power stations, KKS has three different types of code: -

Process-related code

Process-related identification of systems and items of equipment according to their functions in mechanical, civil, electrical and control and instrumentation engineering -

Point of ins tallation code

Identification of points of installation of electrical and control and instrumentation devices in installation units (e.g. in cabinets, panels, consoles) -

Location code

Identification of locations in structures, on floors and in rooms and also of fire areas and topographical stipulations (surface area grid) These three types of code use the same identification scheme, which is subdivided into max. four breakdown levels. The titles of the breakdown levels of the three types of code will be as follows: Serial no. of breakdown level

0

1

2

3

Process-related identification

Total plant

System code

Equipment unit code

Component code

Point of installation identification

Total plant

Installation unit code

Installation space code

Location identification

Total plant

Structure code

Room code

11

2.2

Prefix Symbols and Breakdown Symbol s for Types of Code

The types of code are distinguished in accordance with DIN 40719, Part 2, by means of prefix and breakdown symbols. Serial no. of breakdown level

0

1

2

3

Component code

Process-related identification

=

Total plant

System code

Equipment unit code

Point of installation identification

+

Total plant



Location identification

+

Total plant

Structure code

Prefix symbol



Room code

Breakdown symbol

The "full stop" breakdown symbol for point of installation identification must always be written. The prefix symbols may be omitted if the information contents of the codes remain unambiguous. 2.3

Format of Breakdown Levels

The code consists of breakdown levels. The individual breakdown levels are differently formatted. They consist of classifying and numbering code elements. The latter consist of data characters occupied by alpha characters and numeric symbols. Serial no. of breakdown level

0

Designation of data character

G

Type of data character

A oder N

1

2

F0 F1 F2 F3 N

A

A

A

FN N N

A1 A2 A

A

AN

3 A3

N N N A

B1 B2 A

A

BN N N

A = Alpha characters (Roman letters except I and O, and special symbols) N = Numerical characters (Arabic numerals)

Within the breakdown levels and within the code groups the data characters places from the left to the right smaller becoming units. Read from left to right no data characters may be omitted. Special guidelines apply to data characters G, F0 and A3.

12 2.3.1 Classifying Code Elements The alpha code elements F 1 , F2 , F3 , A1 , A2 and B1 , B2 have a classifying function. Serial no. of breakdown level

0


G


A oder N

1

2

F0 F1 F2 F3 N A

A

A

FN N

N

AN

A 1 A 2 A

A

3

A3

N N N A

B1 B2 A

A

BN N

N

Maingroups F1 Groups F2 Subgroups F 3 Maingroups A1 Subgroups A 2 Maingroups B1 Subgroups B 2 The classifying coding letters and designations are project-independently in the KKS keys as follows: -

Function key, for F1 / F1 F2 / F1 F2 F3 on breakdown level 1

-

Equipment unit key, for A1 / A1 A2 on breakdown level 2

-

Component key, for B1 / B1 B2 on breakdown level 3

The plain text designation of the key may be modified on a project-specific basis but only provided that no content changes take place. Modifications must be taken by the parties involved to the project. "Blocked" coding letters are reserved for future technologies and new engineering systems. They may only be allocated and released by the VGB Working Panel Reference and Designation of Power Plants. The letters of the alphabet are divided up between the main groups A 1 and B1 . For this reason certain letters may not be used within each group.

13

2.3.2 Numbering Code Elements The code elements G, F 0 , FN , AN , A3 and BN have a numbering function. Serial no. of breakdown level

0


G


A oder N

1

2

F0 F1 F2 F3 N A

A

A

FN N

N

A1 A2 A

A

3

A N N

N N

A3 A

B 1 B2 A

A

BN N

N

These numbering code elements are subject to agreement between the project parties and are project-independently regarding the numbering systems and the direction of numbering. However, the following principles apply: -

As a rule numbering starts anew when one of the preceding code elements changes.

-

Numbering may be consecutive or grouping.

-

Numbering need not be continuous.

-

Numbering conventions, once established, may not be altered, not even in the event of changes made in the progress of planning.

-

Redundant zeros must be written. Exceptions are fixed in the following one.

-

An application-specific scheme of numbering may be established. However, such schemes may not have the effect of reserving numbers in other applications, not even within the same engineering discipline.

14

3

Contents of Data Characters

3.0

Total Plant

Serial no. of breakdown level

0


G


(A oder N)

1

2

F0 F1 F2 F3 N

A

A

A

FN N

N

A1 A2 A

A

3

AN N

A3

N N A

B1 B2 A

A

BN N

N

Total Plant

In the breakdown level 0 -

Power station units

-

Non-unit-specific plants

-

Extensions

are marked within location of a power station. The breakdown level 0 is relative for the three types of code and must be fixed in the case of application of the project-taken parts with respect to: -

Contents

-

Type of data character (A or N)

-

Direction of numbering

For the direction of numbering (or lettering) project-dependent local characteristics are determining. The definition of numbering direction in the breakdown level 0 should take place together with the numbering direction in the prefix of breakdown level 1 (see also there). Breakdown level 0 may be omitted if the remaining characteristic remains clear. This has to be specified between the project parties.

15

3.1

Process-Related Identifi cation

Process-related identification of systems and items of equipment according to their functions in mechanical, civil, electrical and control and instrumentation engineering Serial no. of breakdown level

0

1

2

3

Titel of breakdown level

Total plant

System code

Equipment unit code

Component code

Designation of data character Type of data character

G =

(A oder N)

F0 F1 F2 F3 (N) A

A

A

FN N N

A1 A2 A

A

AN

A3

N N N (A)

B1 B2 A

A

BN N N

Prefix sym bol

for process -related code Prefix nu mber for syst em code

Numbering of similar systems and plants within the parts of the power plant designated in breakdown level 0 System c lassification

Classification of systems and plants as per KKS Key System n umbering

Numbering subdivision of systems and plants in system sections, subsystems and/or units Equipment unit cl assification

Classification of mechanical equipment, electrical, control and instrumentation equipment as per KKS Key Equipment unit nu mbering

Numbering of mechanical equipment, electrical, control and instrumentation equipment Ad di ti on al co de

for the equipment unit code Component cl assification

Classification of components, signals or signal applications as per KKS Key Component num bering

Numbering of components, signals or signal applications The data characters in parentheses () can be omitted if the code remains clear. This has to be specified between the project parties.

16

3.1.1 System Code Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N A

A

A

FN N

A1 A2

N

A

A

AN

A3

N N N A

B1 B2 A

A

BN N

N

Prefix nu mber for syst em code

Numbering similar systems and plants referring to F 1 - F3 Within the parts designated for the power plants identified in breakdown level 0 the prefix number applies only to the system or the plant which is classified in the following alpha positions. The prefix number does not replace the numbering in F N or the identification in breakdown level 0. Details of application are to be specified between the project parties particular regarding standard identifications. Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N A

A

A

FN

A1 A2

N N

A

A

AN

A3

N N N A

B1 B2 A

A

BN N

System cl assification

Classification of systems and plants as per KKS Key Coding letters and designations of the main groups F 1 from the Function Key: A

Grid and distribution system

B

Power transmission and and auxillary power supply

C

Instrumentation and control equipment

D

Instrumentation and control equipment (only for use when the function keys CM to CT are insufficient for the identification)

E

Conventional fuel supply and residues disposal

F

Handling of nuclear equipment

G

Water supply and disposal

H

Conventional heat generation

N

17 J

Nuclear heat generation

K

Nuclear auxiliary system

L

Water, steam, gas cycle

M

Main machine set

N

Process energy supply for external users (e.g. district heating)

P

Cooling water system

Q

Auxiliary system

R

Gas generation and treatment

S

Ancillary system

T

blocked

U

Structure

V

blocked

W

System for regenerative-energies

X

Heavy machinery (not main machine set)

Y

blocked

Z

Workshop and office equipment

The subdivisions in F 2 and F3 are given in the applicable Function Key. Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N

A

A

A

FN N

N

A1 A2 A

A

AN

A3

N N N A

B1 B2 A

A

BN N

N

System n umbering

Numbering subdivision of systems and plants into subsystems and sections of plants The numbering starts anew when one of the preceding code elements changes. The FN code element has no general-applicable classifications. Redundant zeros must be written. Details of application are to be specified between the project parties.

18

3.1.2 Equipment Unit Code Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N

A

A

A

FN N

N

A 1 A 2 A

A

AN

A3

N N N A

B1 B2 A

A

BN N

N

Equipment unit classification

Classification of mechanical equipment, electrical, control and instrumentation equipment as per KKS Key Coding letters and designations of the main groups A 1 , as mentioned in the Equipment Unit Key: A

Equipment unit

B

Apparatus

C

Direct measuring circuit

D

Closed-loop control circuit

E

Analog and binary signal conditioning

F

Indirect measuring circuit

G

Electrical equipment

H

Subassembly of main and heavy machinery

J

Nuclear assembly

The subdivisions in A 2 are given in the applicable Equipment Unit Key. Main group A 1 = H may only be used in connection with the main groups of the system code F 1 = M "Main machine set" and F 1 = X "Heavy machinery". Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N

A

A

A

FN N N

A1 A2 A

A

A N

A3

N N N A

B1 B2 A

A

Equipment unit numbering

Numbering of mechanical equipment, electrical, control and instrumentation equipment Redundant zeros must be written.

BN N

N

19 Details of application are to be specified between the project parties. Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N

A

A

A

FN N N

A1 A2 A

A

AN

A 3

N N N (A)

B1 B2 A

A

BN N N

Ad di ti on al co de

for the equipment unit code The additional code is used for the numbering of: -

Pilot valves and overpressure protection equipment

-

Electrotechnical multiple supplies

-

Measuring circuits which share one sensor

The additional code is not a replacement code for the components designated in breakdown level 3. It may be omitted if the code remains clear. Further applications are to be specified between the project parties. 3.1.3 Component Code Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N

A

A

A

FN N N

A1 A2 A

A

AN

A3

N N N A

B1 B2 A

A

BN N

Component Classification

Classification of components, signals or signal applications as per KKS Key Coding letters and designations of main groups B 1 for components from the Component Key and for signals and signal applications: -

Electrical component (to DIN 40719, Part 2)

K

Mechanical component

M

Mechanical component

Q

Instrumentation and control component (non-electrical)

N

20

X

Origin signal

Y

Signal application

Z

Gated signal

Subdivisions in B 2 for components are given in the applicable Component Key. No generally valid rules have been established for subdivisions for "signals and signal applications" since such subdivisions depend on the design of the control and instrumentation systems. The definition of the subgroups is to be specified of the project parties. Serial no. of breakdown level

0

1

2

3


Total plant

System code

Equipment unit code

Component code


G =

A oder N

F0 F1 F2 F3 N

A

A

A

FN N

N

A1 A2 A

A

AN

A3

N N N A

B1 B2 A

A

Component nu mbering

Numbering of components, signals and signal applications Redundant zeros must be written. Details of application of the component code are to be specified between the project parties.

BN N

N

21

3.2

Point of Installatio n Identifi cation

Identification of points of installation of electrical and control and instrumentation devices in installation units (e.g. in cabinets, panels, consoles). Serial no. of breakdown level

0

1

2


Total plant




G +

(A oder N)

F0 F1 F2 F3 (N) A

A

FN

A N N

A1 A2 

AN

A3

A (A) (N) (N) N (A)

Prefix sym bol

for point of installation code Prefix number for inst allation unit code

Numbering of similar installation units within the parts of the power plant designated in breakdown level 0 Classification of i nstallation unit

Classifying subdivision of installation units, e.g. cubicles, consoles, cabinets, panels Numbering of in stallation unit

Numbering subdivision of installation units Breakdown symbol " full stop" Designation of location cod e Vertical subdi vision (rows)

of installation spaces in installation units Designation of location cod e Horizontal subdivsi on (columns)

of installation spaces in installation units Ad di ti on al c od e fo r designation o f location c ode

Designation of special installation locations of components or further subdivision of A N The "full stop" breakdown symbol must always be written. The data characters in parentheses () can be omitted if the code remains clear. This has to be specified between the project parties.

22 3.2.1 Installation Unit Code Serial no. of breakdown level

0

1

2


Total plant




G +

A oder N

F0 F 1 F 2 F 3 (N) A

A

A

FN N N

A1 A2 

A

AN

A3

A N N N A

Prefix num ber of installation unit code

Numbering of similar installation units within the parts of the power plant designated in breakdown level 0 The prefix number applies only to the installation units addressed in the subsequent alpha characters. If it is not possible to classify all installation units in F 3, the prefix number F 0 may be used to supplement this classifying information. It does not replace the numbering in FN and not the identification in breakdown level 0. Details of application are to be specified between the project parties. Serial no. of breakdown level

0

1

2


Total plant




G +

A oder N

F0 F1 F2 F3 N A

A

A

FN N N

A1 A2 

A

A

AN

A3

N N N A

Classific ation of installation unit

Classifying subdivision of installation units, e.g. cubicles, consoles, cabinets, panels Coding letters and designations of the main groups F 1 from the Function Key: A

Grid and distribution system

B

Power transmission and auxiliary power supply

C

Instrumentation and control equipment

D

Instrumentation and control equipment (only for use when function keys CM to CT are insuffcient for the identification)

The subdivisions in F 2 and F3 are given in the applicable Function Key. Special engineering-discipline-specific rules apply to installation unit classification in connection with other F 1 main groups.

23 Serial no. of breakdown level

0

1

2


Total plant




G +

F0 F1 F2 F3

A oder N

N

A

A

A

A1 A2

FN N N



A

A

AN

A3

N N N A

Numbering of in stallation unit

Numbering subdivision of installation units The numbering starts anew when one of the preceding code elements changes. Redundant zeros must be written. Details of application are to be specified between the project parties. 3.2.2 Installation Location Code Serial no. of breakdown level

0

1

2


Total plant




G +

A oder N

F0 F1 F2 F3 N

A

A

FN

A N N

A 1 A 2 

A

A N

A3

(A) (N) (N) N (A)

Vertical subdi vision (rows)

of installation locations in installation units Horizontal subdivi sion (columns)

of installation location in installation units Ad di ti on al Cod e

Designation of special installation locations of components or further subdivision of A N The number of data code places depends on the necessary fine classificationl of the field rasters. The code places in parentheses () can be omitted if the code remains clear. Deviations in accordance with DIN 40719 Part 2 are allowed and must be specified between the project parties.

24

3.3

Identific ation of Location

The identification of locations in structures, floors, rooms as well as fire areas and topographical definitions (surface area grid). Serial no. of breakdown level

0

1

2


Total plant

Structure code

Room code


G +

(A oder N)

F0 F1 F2 F3 (N) A

A

A

FN N N

A1 A2

AN

A3

(A) (A) (N) N N (A)

Prefix symbol

for the location code Prefix number for struc ture code

Numbering of similar structures within the parts of the power plants identified in breakdown level 0 Classific ation Structur e

Classifying subdivision of structures (open area as well) Numbering of flo ors

Numbering subdivision of structures into floors, storeys, platforms, elevations, etc. Classific ation of Rooms

Identification of rooms and fire areas Room numbering

- Numbering of rooms and fire areas in each floor (number code) or - Designation of grid squares in each floor (field raster) Ad di ti on al c od e

for subdivision of room number The data characters in parentheses () can be omitted if the code remains clear. This must be specified between the project parties.

25

3.3.1 Structure Code Serial no. of breakdown level

0

1

2


Total plant

Structure code

Room code


G +

A oder N

F0 F1 F2 F3 (N) A

A

A

FN N N

A1 A2 A

A

AN

A3

N N N A

Prefix numer for str uctur code

Numbering of similar structures within the parts of power plant identified in breakdown level 0 Each prefix number applies only to the structures classified under F 1 specified between the parties to the project. Serial no. of breakdown level

0

1

2


Total plant

Structure code

Room code


G +

A oder N

F0 F1 F2 F3 N A

A

A

FN N N

A1 A2 A

A

AN

A3

N N N A

Classification Structure

Classifying subdivision of structures (open area as well) Coding letters and designations for main groups F 1 from the Function Key. U

Structure

The subdivisions into F 2 and F3 are to be taken out of the each valid Function Key. No generally binding rules have been established for the subgroups F 3 of groups UA and UX. Definitive rules are to be specified between the project parties.

26

Serial no. of breakdown level

0

1

2


Total plant

Structure code

Room code


G +

A oder N

F0 F1 F2 F3 N

A

A

A

FN N

N

A1 A2 A

A

AN

A3

N N N A

Numbering of flo ors

Numbering subdivision of structures into floors, storeys, platforms, elevations etc. Numbering begins anew for each structure. The direction of numbering is vertical from the lowest floor upward. Details of application are to be specified between the project parties. 3.3.2 Room Code The room code serves to identify physically separated and fictitious rooms in structures and in the open area Physically separated rooms in structures are usually identified in numbering, grid squares in the open are by field raster. Fictitious rooms in structures can be identified by numbering method with field raster.

27

3.3.2.1 Room Identification by Numbering Serial no. of breakdown level

0

1

2


Total plant

Structure code

Room code


G +

A oder N

F0 F1 F2 F3 N

A

A

A

FN

A 1 A 2

N N

(A)

A N

(N) N N (A)

Classification of r oom

Identification of rooms and fire areas Identification letters and designations for main group A 1: R

Room (can be omitted if code remains clear)

S

Fire area (must always be written)

A 2

is not used when numbering room coding in numbering method Numbering of Room

Numbering of rooms and fire areas in each floor Chambers and rooms and over several floors going areas receive the room numbering of the lowest floor in all floors. The 100er place can be omitted if no structure of the entire plant knows more than 99 rooms. If this does not apply, all room numbering codes of the entire plant must be written uniformly with three data code places in AN Ad di ti on al co de

for subdivision of room number

A3

28 3.3.2.2 Room Identification by Field Raster Serial no. of breakdown level

0

1

2


Total Plant

Structure Code

RoomCode


G +

F0 F1 F2 F3

A oder N

N

A

A

A

FN N N

A 1 A 2 A

A

A N

A3

(N) N N (A)

Classific ation of Room

Data character A1 = R must always be written Field raster on high valu e (alphanumeric )

The numeric data character can be omitted Field raster on easti ng (numeric ) Ad di ti on al c od e

for subdivision of grid The grid squares are in their dimensions through on a scale suitable field rasters (see DIN 1356) to specified related to a in-measured origin (e.g. acc. Gauß-Krüger). The grid sizes and the meaning and type of the data code places (A or N) must be specified between the project parties.

29

4

Notation of Codes

The codes can be written with and without spacing but however it must be represented in such a way that misinterpretations are avoided. The allowable way of writings is fixed. Their use for any intended purpose is to be specified between the project parties. Spaced way of writing supports the detectability and memory quality of codes. It can be spaced by blank codes as well as by more-cellular way of writing "Small spacing" Blank spaces or dividing lines between the breakdown levels for codes which do not have visually to be seized within a time limit. "Large spacing" Blank spaces or dividing lines between the alpha part and the numeric parts within the breakdown levels, if these are more than four data code places long, e.g. for codes in the control room, where in relatively short time codes must be seized.

Small spacing

Large spacing

with blank spaces

A NAAANN AANNNA AANN

A NAAA NN AA NNA AANN

with dividing lines

A|NAAANN|AANNNA|AANN

A|NAAA|NN|AA|NNA|AANN

Multiple-line

A NAAANN AANNNA AANN

A NAAA NN AA NNNA AANN

If an identification code is written together with abbreviations within a text, the code designation must be enclosed in asterisks (*LAC*) to avoid confusion.

30

5

Special Rules

5.1

Rules to the Keys

The KKS Key is divided into the following key parts: -

Function Key

-

Equipment Unit Key

-

Component Key

Free spaces:

A number of coding letters in main groups F1 groups F2 and subgroups F 3 have been reserved, for example to allow inclusion of future technologies. In main groups A 1 and B1, as well as in some subgroups, some coding letters have also been reserved. All reserved coding letters can only be allocated with the agreement of the VGB Working Panel “Reference Designation and Plant Documentation”. In the Function Key it is not possible to make generally valid rules for certain coding letters in data characters F 2 and F3 since they depend exclusively on the configurations and arrangements concerned. Similar considerations apply to A 1 = E and G in the Equipment Unit Key. In such cases a remark with the following meaning appears in the key part concerned: " ...free for u se for"

i.e. the letters thus annotated may be used within the terms of the stated definitions

or " ...free for use"

i.e. unreserved letters may be used without any restrictions within the terms of the stated definitions in F 1 resp. F2

Details of application are to be specified between the project parties.

31 Interfaces

The relevant pages of the Function Key show the interface definitions with the meanings given below:

"from incl."

means "including" the named item

"from excl." means "excluding" the named item "to excl."

means "excluding" the named item

"to incl."

means "including" the named item

For some main groups F 1 as e. g.: F

Handling of nuclear equipment

J

Nuclear heat generation

K

Reactor auxiliary system

the task of the system concerned is defined in addition to or instead of the interfaces. 5.2

System Codes for Heavy Machi nery

Certain 'components' such as steam turbines used as drives for feedwater pumps can require so many identification details that, as 'heavy machinery', they need separate system codes in order to permit identification of all associated mechanical equipment units and electrical, control and instrumentation facilities. The system codes for such heavy machinery are fixed as X in main group F 1 . 5.3

Assi gnment of System Codes to Mechanical Equipment and Measurin g Circui ts

Equipment units are allocated to the system in which they are installed. When stipulating system boundaries the originator principle applies. For identification purposes, measuring circuits are allocated to the system where the parameters are measured. 5.4

Special Rules for Mechanical Engineering

5.4.1 Valves Valves as control elements in medium-prominent systems are allocated to the system in which they are installed. Irrespective of their type of actuation they are identified by AA in breakdown level 2. Valves in medium-prominent measuring circuits are allocated to the measuring circuit and are identified by KA in breakdown level 3.

32

Shutoff valves between medium-prominent systems and a measuring circuit are allocated to the medium-prominent system and identified by AA in breakdown level 2. Note: the originator principle does not apply here. Safety equipment comprising safety valves and the connected piping is allocated to the system to which it is connected. Note: the originator principle does not apply here. 5.4.2 Supports Supports are not identified in line with the originator principle. They can be allocated to a system designation or a building/structure designation in breakdown level 1. System-oriented identification is a feasible alternative when parts of the support can be allocated to a particular system. A building/structure-oriented identification is preferable when parts of different systems share supports. Supports are identified by BQ in breakdown level 2. Details of application are to be specified between the project parties 5.4.3 Supply Systems Where equipment units identified in breakdown level 1 and 2, require their own supply systems, these supply systems are identified as subsystems to the overall system with an identification code in breakdown level 1. Supply systems serving several main groups of breakdown level 1 are treated as independent supply systems and are provided with a key within the following main groups in F1: G

Water supply and disposal

K

Reactor auxiliary system

Q

Auxiliary system

S

Ancillary system User (system)

Supply system

Code

Designation

L..

Steam, water, gas cycle

M..

Main machine set

Code

Designation

Q ..

Auxiliary system (common to L.. and

M..)

If several systems F 2 or F3 are connected to a particular supply system, the following code letters are stipulated for the corresponding data character F 2 or F3 in breakdown level 1: V

Lubricant supply system

W

Sealing fluid supply system

X

Fluid supply system for control and protection equipment.

The stipulations for V and W do not apply to main groups A, B, C, D, U and Z of breakdown level 1.

33 The use of the letters at data characters F 2 and F3 is illustrated in the following table using the sealing fluid supply system as an example. User (system)

Supply system

Code

Designation

LA.

Feedwater system

LB.

Steam system

LC.

Condensate system

LAB

Feedwater piping system

LAC

Feedwater pump system

LAD

HP feedwater heating system

5.5

Code

Designation

LW.

Sealing fluid supply system for steam, water, gas cycle (common to LA., LB. u. LC.)

LAW

Feedwater sealing water system (common to LAB, LAC and LAD)

Special Rules for Civil Engineering

If a building or structure covers several engineering process systems, the code for this building is priority-specified. Details of application are to be specified between the project parties. For the identification of special structures, ducting and bridge structures in main group F 1 = U the subgroups F 3 = X

Special structures

Y

Bridge structures

Z

Ducting structures

are stipulated in almost all cases. 5.6

Special Rules for Electri cal, Contro l and Instru mentation Engin eerin g

5.6.1 Shared Equipment for Electrical, Control and Instrumentation Engineering Combined electrical, control and instrum entation equipment

Combined electrical, control and instrumentation equipment for measurement, closed- and open-loop control and power unit (e. g. combined in one cabinet) are identified in breakdown level 1 using the letters CM to CT (subdivision for system combinations). If necessary a further grouping can be made in F N. Transducer Racks, Supports, Scaffolding

These are not identified according to the originator principle. They can be allocated a system code (e. g. auxiliary equipment at main machine sets and heavy machinery) or a building/structure code in breakdown level 1. In breakdown level 2 transducer racks, supports and scaffolding must receive the key GZ. Subdistributo r, Penetrations

These are not identified according to the originator principle. In breakdown level 1 they are provided with the code for the building/structure and floor in which they are located.

34 Exceptions are, for example, the subdistributors at the main machine sets and heavy machinery and the subdistributors in electrical, control and instrumentation cubicles and cabinets, which in breakdown level 1 are identified according to the main machine set or heavy machinery, cubicle or cabinet. In breakdown level 2 the subdistributors are to be identified by the key A 1 = G (electrotechnical equipment). Penetrations through the reactor containment

Such penetrations are identified by JML=reactor containment, cable penetration in breakdown level 1 according to the originator principle. Connections

Identification of connections is performed in line with DIN 40719 Part 2 in a dedicated code block separated from the existing code designation by a colon ":" as required and according to the originator principle. This code block may contain any combination of alphanumeric symbols. Cable Number

For the classifying part of the cable characteristic the characteristic one of the two cable goals is used totally or partly, whereby the characteristic of the cable goal is usually used, which stands further in front in the alphabet. The numbering part of the cable no. consists of four numerical data characters or of three numerical and one alphabetical character; grouping according to voltage level, for example, is allowable. 5.6.2 Electrical Equipment Transform er Systems for Power Transmission and Auxili ary Power Supply

These transformers are identified on breakdown level 1. In breakdown level 2, the individual windings are identified (but not on a phase-specific basis) by means of GT for transformer equipment and numbered starting on the high-voltage side. For further details see DIN 42513. Switch gear, Battery Chargers, Inverters and B attery Sets

These systems and items of equipment are identified regardless of equipment location in the classifying part of breakdown level 1 in accordance with the rules for main group F1 = B. If the letters available are insufficient, FN may be used. In such instances the first character of FN has a classifying purpose. In the second number of F N the fields are counted over. 5.6.3 Control and Instrumentation Equipment 5.6.3.1 Measuring Circuits The identification code of the measuring circle covers the recording of measurement, preparation and distribution as well as the registering and indicating measured variable processing. Measuring circles are assigned marking-technically to the system, in which the measured variable is measured. On breakdown level 2, direct measuring circuits are identified by means of A 1 = C, indirect measuring circuits (linked or calculated) by means of A 1 = F and in A2 according to the measured physical variable (e.g. pressure, temperature) in accordance with DIN 19227 Part 1.

35 Equipment Unit-Specific Analog Signal Processing and Measuring Circuits

Equipment unit-specific analog signal processing elements comprise control and instrumentation equipment which is only provided for one equipment unit such as control interface, protective logics, instruments in the feeder and command termination for final control elements. These analog signal processing elements receive the code of the equipment unit concerned. System-Specific Analog Signal Processing

System-specific analog signal processing elements comprise links between more than one measuring circuit and/or equipment unit-specific analog signal processing elements for systems such as open-loop controls (but not control interfaces). They encompass the control and instrumentation equipment for more than one equipment unit and are identified on breakdown level 2 by means of A 1 = E (analog and binary signal conditioning). A 2 identifies control and instrumentation functions (e.g. alarm links, subgroup control). System-Interfacing Analog Signal Processing

Where control and instrumentation equipment serves more than one process system identified in F2 and F3 , the letter Y for generic control and protection systems may be used in the appropriate data character on breakdown level 1. Control and instrumentation equipment which serves more than one main group may be identified under main group C for control and instrumentation, e.g. unit control system = CJA. Process-related systems

Generic function key

Code

Designation

Code

Designation

LAB

Feedwater piping system

LAC

Feedwater pump system

LAY

LAD

HP feedwater heating system

Control and protection system for feedwater system (common to LAB, LAC and LAD)

LA.

Feedwater system

LB.

Steam system

LY.

Control and protection system for steam, water, gas cycle (common to LA. and LB.)

H..

Conventional heat generation

L..

Steam, water, gas cycle

CJA

Unit control system (common to H.., L. and M..)

M..

Main machine set

Given the possibilities shown in the table, it is not practicable to meet all possible requirements for identification of discrete process-related functions (e.g. functional group control). Thus for example, it may be necessary to use items which are identified differently on breakdown level 1 (main system and associated parts of auxiliary and ancillary systems) in order to fulfil a given process-related task (functional group). Identification of the functional groups involved in process-related tasks so as to relate them to the principal task concerned may be performed by using the alpha characters in F 1 F2 F3 of the principal process-related task. In this application, however, a suitable identifier such as a prefixed Y should be used to indicate that a software coding unit is concerned, thus to rule out confusion with processrelated codes. This code has to be specified between the parties to the project.

36 An alo g Si gn al Li nk age

In principle it applies with signal logics that after linkage for e.g. reporting linkages the characteristic of the signal which can be processed remain keeping as far as possible. Linked analog signals representing physically similar direct measured variables are identified by means of a set number, e.g. "9", in the first data character of AN and retain the code of the physical variable in data character A 2 . Linked analog signals representing physically dissimilar indirect measured variables are identified by means of A 2 = U (combined variables). Where signals or measured data are used to limit or suppress the original measured data, the processed output signal retains the code of the original measured data. Where measured data are corrected (e.g. flow measurement corrected for pressure and temperature) and if only the corrected measured data are further processed, the codes stay the same as those of the original measured data in spite of the gating of dissimilar measured data. If calculated measured values from linkages of measured value from the origin measured value are to be differentiated to, then the indirect (calculated) measured variable is to be marked by A 1 = F (indirect measuring circles) in the data code place A1. The identification in the data code place A 2 takes place after physical dimension. 5.6.3.2 Closed-Loop Control Circuits The principles for the identification of measuring circuits apply analogously to the identification of closed-loop control circuits on breakdown level 1. Every control loop and every closed-loop control circuit comprises measuring, control and positioning elements regardless of whether electrical, pneumatic, hydraulic or other items of equipment are used. Closed-loop controls are identified according to the controlled variable and not after the measuring circuits which serves the control or the final control element on which the control acts. 5.6.3.3 Signals and Signal Applications Breakdown level 3 is used to identify signals and their applications. For this purpose, data character B1 can contain X

Signal origin

Y

Signal application

Z

Gated signal

No generally valid rules have been made for signal and application areas. They must be established individually for different control and instrumentation concepts.

37

6

Appendix: Compendium of " Establishments between the Parti es to the Project" to b e made on a Proj ect-Specific Basis

The KKS Guidelines do not contain all the rules necessary for a project. There are free spaces for which clear definitions have to be made between the purchaser (owner/operator) and the vendor (architect/engineer/ supplier) in the form of projectspecific establishments prior to completion of the contract. In the Guidelines such aspects are indicated by the remark "Details of application to be specified between the parties to the project". A list of such establishments is given below. Reference to Guidelines Page General establishments

1. Changes to KKS designations (only possible as long as contents stay the same)

12

2. Rules on numbering systems and direction of numbering for all numbering code elements

12

3. Rules on breakdown level regarding - Contents - Type of data character - Direction of numbering

13

4. Rules on spacing for code notation

27

5. Allocation of unreserved, but "free for use" available classifying code elements

28

Establishments on Process-Related Identification

6. Use of data characters in process-related identification

14

7. Use of prefix number F0

15

8. Rules on FN numbering

16

9. Rules on AN numbering

17

10. Rules on A3 numbering

18

11. Rules on BN numbering

19

12. Rules on the identification of supports

31

13. Rules on the identification of supply systems

31

14. Rules on the identification of system-interfacing analog signal processing

34

15. Rules on identification for "signals and signal applications" and for the reservation of the subgroups of main groups X, Y, Z on breakdown level 3

35

Establishments on Point of Installation Identification

16. Use of data characters in point of installation identification

20

38 17. Use of prefix number F 0 in installation unit code

21

18. Rules on FN numbering in installation unit code

22

19. Installation space identification

22

Rules in Location Identification

20. Use of data characters in location identification

23

21. Use of prefix number F 0 in structure identification

24

22. Rules on subgroup F 3

24

23. Rules on FN numbering in structure identification

25

24. Rules on room identification

25

25. Rules on structure identification for individual structures combined to form one structure

32

26. Rules on structure identification for duct and bridge structures as connecting structures

32

39

40

7

KKS Identi fik ation System for Power Plants

___________________________________________________________________ Revisio n sheet Page

Index

Date of change

Status: August 2007

WP Ref. Desig. and Plant Doc. date of determination

Explanation of revision

d

05/07

21.11.2006

BU1, BU2

d

05/07

08.05.2007

BV1

d

05/07

08.05.2007

BV Direct voltage distribution boards, ……… change voltage into: current

BV1

d

05/07

08.05.2007

BVA-BVS Direct voltage emergency distribution boards….. change voltage into: current

BW1

d

05/07

08.05.2007

BW Direct voltage distribution boards, ……. change voltage into: current

BW1

d

05/07

08.05.2007

BWA-BWS Direct voltage emergency distribution boards, … change voltage into: current

GN1

d

05/07

08.05.2007

GNH: Deaeration

EA1

EA_, EAA, EAB, EAC, EAE: Supplement „Loading“ resp. „Unloading System“ in the relevant designation codes resp. within the limits BU, BUA-BUS Direct voltage distribution boards, …….. change voltage into: current

„drying system“ omit G1

HN1

MB1

MH1 MH1

GL: Limiting equipment (i.g. short circuit current limiting reactor) New in the equipment unit key

d

05/07

20.02.2006

d

05/07

08.05.2007

d

05/07

08.05.2007

d

05/07

17.05.2005

MH_: Steam motor system New letter code

d

05/07

07.07.2005

MHA bis MHZ: New determinations at MH (F3 classification)

HNG: Flue gas heating utilisation system New letter code MBL: Intake air, cold gas system incl. intake air preheating New determination

41

KKS Identif ikation Syst em for Power Plants ___________________________________________________________________ Revisi on sheet Page

Index

Date of change

WP Ref. Desig. and Plant Doc. date of determination

M1

d

05/07

20.02.2006

M1

d

05/07

20.02.2006

Status: August 2007 Explanation of revision

MQ: permanent connection New determination in component key MP: permanent connection (if MQ is not enough) New determination in component key

42

KKS Identif ikation System for Power Plants __________________________________________________________________________ Revis ion sheet 7 - function key Key indication x e d n I

Conclusion of WP Ref. Desig. and Plant Doc. from

Status:

January 2010


– blocked – changed into Earthing and lightning protection system acc. to B105d

BAU

E

13.08.2009

BAW

E

13.08.2009

GHW

E

25.11.2009

new determination: Seal Fluid Supply System

HE

E

26.11.2008 13.08.2009

new determination: Oxydent production / -supply

HEA

E

26.11.2009

new determination: Air intake, air supply

Earthing and lightning protection system changed into: – blocked – acc. to B105d

limits: from incl. ambient air to excl. inlet air compression and / or from incl. compressor casing and rotor gas turbine to excl. inlet cooling and cleaning

HEB

E

26.11.2009

new determination: Air compression limits: from excl. air intake to excl. cooling and cleaning

HEC

E

26.11.2009

new determination: Cooling and cleaning inclusive regeneration limits: from excl. air compression to excl. main heat exchanger

HED

E

26.11.2009

new determination: Main heat exchanger / cold production / condensation From excl. cooling to excl. rectification to excl. oxygen release to excl. nitrogen release to excl. argon to excl. residual gas release

43

KKS Identifi kation System for Power Plants __________________________________________________________________________________________

Revis ion sheet 7 - function key Key indication x e d n I


Status:

January 2010


HEE

E

26.11.2009

new determination: Rectification

HEF

E

26.11.2009

new determination: Chemical looping system from excl. air intake to excl. contiguous systems

HEG

E

26.11.2009

new determination: Membrane separate system from excl. air compression to excl. oxygen release

HEJ

E

26.11.2009

new determination: Oxygen-release inclusive storage from excl. main heat exchanger to excl. ducting system oxygen

HEK

E

26.11.2008

HEL

E

26.11.2009

new determination: Nitrogen-release inclusive storage from excl. main heat exchanger to excl. ducting system nitrogen new determination: Argon-release inclusive storage from excl. main heat exchanger to excl. ducting system argon

HEM

E

26.11.2009

new determination: Residual gas-release from excl. main heat exchanger to incl. atmosphere

HEV

E

26.11.2009

new determination: Lubricant system

HEW

E

26.11.2009

new determination: Sealing medium system

HEX

E

26.11.2009

new determination: Fluid supply system for control and protection systems

44




Status:

January 2010


HEY

E

26.11.2009

new determination: Control and protection system

HG

E

26.11.2009

new determination: CO2 Conditioning in flue gas

HGA

E

26.11.2009

new determination: CO2-precleaning from excl. chemical flue gas treatment to excl. CO² raw gas condensation

HGB

E

26.11.2009

new determination: CO2 raw gas condensation from excl. CO²-precleaning to excl. CO²-raw gas cooling

HGC

E

26.11.2009

new determination: CO2 raw gas cooling and –cleaning incl. regeneration from excl. CO² raw gas condensation to excl. main heat exchanger

HGD

E

26.11.2009

new determination: Main heat exchanger / cooling / liquidation from excl. CO2 raw gas cooling / cleaning to excl. rectification

HGE

E

26.11.2009

new determination: Rectification from excl. main heat exchanger to excl. CO2 buffer system

new determination: Ducting for rectification

HGF

E

26.11.2009

HGU

E

26.11.2009

new determination: CO2 tank / - buffer system

HGV

E

26.11.2009

new determination: Lubricant system

45




Status:

January 2010


HGW

E

26.11.2009

new determination: Sealing fluid supply system

HGX

E

26.11.2009

new determination: Fluid supply system for control and protection systems

HGY

E

13.08.2009

new determination: Control and protection systems

HK

E

02.04.2009

new determination: CO2 separation in flue gas

HKA

E

13.08.2009

new determination: flue gas channel system within *HK*

HKB

E

13.08.2009

new determination: flue gas ducting system

HKC

E

13.08.2009

new determination: fan system for flue gas

HKD

E

13.08.2009

new determination: CO2 absorption from incl. inlet flue gas inclusive water separation

HKE

E

13.08.2009

new determination: Flue gas pre-cleaning

HKF

E

13.08.2009

new determination: detergent conditioning

HKG

E

13.08.2009

HKH

E

13.08.2009

new determination: System loaded/unloaded detergent from incl. outlet CO 2 absorption to incl. inlet CO2 desorption inclusive heat transfer resp. from incl. outlet CO 2 desorption to incl. inlet CO2 absorption new determination: CO2 desorption of detergent from incl. inlet detergent desorption to incl. outlet detergent desorption to incl. inlet CO2 conditioning (*HG*)

46

KKS Identif ikation System for Power Plants __________________________________________________________________________________________



Status:

January 2010


HKJ

E

13.08.2009

new determination: detergent supply inclusive storage

HKK

E

13.08.2009

new determination: detergent disposal

HKV

E

13.08.2009

new determination: lubricant supply system

HKW

E

13.08.2009

new determination: sealing fluid supply system

HKX

E

13.08.2009

new determination: fluid supply system for control and protection systems

HKY

E

13.08.2009

new determination: control and protection systems

HL

E

13.08.2009

Modification: Combustion air system (air, oxygen)

HLA

E

13.08.2009

Modification: Ducting system air from incl. excl. air inlet to excl. branch off firing resp. mill air system and carrier air system to excl. branch off *HFE*, excl. fan system, air heater system and gas turbine exhaust system

HLB

E

13.08.2009

Modification: Forced draught fan system from incl. inlet forced draught fan system to excl. outlet forced draught fan system

HLC

E

13.08.2009

Modification: Air preheating (not flue gas heated) from incl. inlet preheating to incl. outlet preheating

HLD

E

13.08.2009

Modification: Air preheating flue gas heated from incl. inlet preheating to incl. outlet preheating

HLE

E

13.08.2009

Modification: Ducting system oxygen

47




Status:

January 2010


HLF

E

13.08.2009

new determination: Oxygen fan system from incl. inlet fan system to excl. outlet fan system

HLG

E

13.08.2009

new determination: Oxygen preheating (not flue gas heated) from incl. inlet preheating to incl. outlet preheating

HLH

E

13.08.2009

new determination: Oxygen preheating flue gas heated from incl. inlet preheating to incl. outlet preheating

LNG

E

25.10.2007

new determination: Removal system for external purpose

LNH

E

26.05.2008

new determination: Spillway limits: from dam / weir

LPG

E

25.10.2007


LQG

E

25.10.2007


RA

E

02.04.2009

Amendment: gas generation (gasification, fermentation)

RAA

E

02.04.2009

Amendment: gas generator (gasifier, fermenter) from incl. fuel, ignition fuel and fluxing agent inlet or from excl. burner and nozzle system to excl. removal system or to excl. solids separator and recycle system or to excl. gas generator quench gas section or to incl. main gas outlet

VGB KKS Code

Recommend Documents