Face drilling/long-hole drilling
Atlas Copco Hydraulic rock drills
COP 1838ME/HE Technical specifcation
A series of high-speed, hydraulic rock drills for face drilling and long-hole drilling in the hole range 38–89 (102) mm. High penetration rates and excellent drill steel life.
Features and benefts • Efcient, hydraulic dual-damping system absorbs and dissipates the shockwaves from the rock, as well as establishing the best possible contact between the drill bit and the rock. This feature makes it possible to transmit maximum power to crush the rock without risking nontightening of threads in the drill string. • Impact piston design matches the size of the drill steel. This feature gives minimum drill steel stress. • Powerful, stepless variable and reversible rotation motor gives high torque for efcient drilling, and minimizes the risk for jamming. • Separate lubrication of fronthead and driver together with pressurized and lubricated mating surfaces and sidebolts for the best protection against wear and corrosion. • The low prole of COP 1838ME/HE permits drilling close to walls with only 2 degrees lookout angle. • Two nitrogen-charged accumulators plus one accumulator for the return oil, levels out pressure peaks in the hydraulic systems. This reduces vibrations and wear on hydraulic components.
Face drilling/long-hole drilling
Technical data COP 1838ME/HE Dimensions anD weight
imPaCt ratings CoP 1838me
CoP 1838he
170
174
1 008
1 098
Width including connectors, mm
251
Height, mm Height over drill center, mm
Weight, kg Length without shank adapter, mm
CoP 1838me
CoP 1838he
Impact power, max, kW
18
19
Input power to rock drill, max, kW
31
32
316
Hydraulic pressure, max, bar
230
230
223
223
Flow rate, l/min
75–92
71–90
88
88
Impact frequency, Hz
60
42-50
Impact energy, Nm
330
360
CoP 1838me
CoP 1838he
Flushing water pressure, max, bar
25
25
Lubricating air consumption at 2 bar, l/s
5
5
40–120
105–165
rotation motors CoP 1838me
CoP 1838he
05 OMS100/ 07 OMS160
09 OMS250
Rotation range, rpm
0–340/215
0–140
Torque, max, Nm
640/1 000
980
Working pressure, max, bar
210
175
Oil consumption, l/min
75
75
Type
flushing flow anD Pressure
Flushing water consumption, l/min*
*Flushing water consumption depends strongly on hole diameter, bit type, drill rod size and rock hardness. The gures above are typical values for spherical button bits in granite, 200 MPa.
Penetration rate m/min
7 6 5
COP 1838ME
4 3
COP 1838HE
Limestone 160 MPa
2 1
Granite 200 MPa
0 40
50
60
70
80
90
100 Ø mm
Hole dimension
Laboratory test results
overhaul kits
shank aDaPters CoP 1838me
Guide diameter, 38
Guide diameter, 52
Seal kit
3115 9150 96
3115 9153 92
400 impact hours kit
3115 9238 90
3115 9153 93
Overhaul kit
3115 2118 90
CoP 1838me gd d 38
CoP 1838he
3115 2119 90
3115 9153 94
CoP 1838me/he gd d 52
Drifting
Long-hole drilling
Long-hole drilling
R32
403-09101,10
403-09103,10
403-09103-18,10
TC35
N/A
N/A
469-09103-18,10
R38
404-09101,10
404-09103,10
N/A
T38
435-09101,10
435-09103,10
435-09103-18,10
SR38
427-09101,10
427-09103,10
N/A
T45
N/A
N/A
436-09103,10
T51
N/A
N/A
437-09103,10
. n s i o i t h t a n r m i o s o n t i o c h f p i d c n e p a s s r n o o i t r e a t r t s n e u C l l I r . e d m e o t t i b s i u h C o r p o c s p i o C o s e a r e l t h t A t r r a u p o y y t n l a u s r n o o s t C . n e e c t i t n o o c n e t u h t o h t o i g w n e i y g p n o a c h r c o o e t s t u c e d j b e u z s i r o e r h t a u t a n n u e m y i n p A u . q o e c d p o n a C s s n a i o l t t A a c f o i s c e k r p a S . m e e s d i a w r r t e e r h a t o n r o o i t s a c n o i i l b t a u c p f s i c i h t e p n s i g s i n e d m r a a n g t e c r u e d d o a r p m l i s l A y . t n n e a d r e r a w S w , o o N r . b s e a r r Ö t x , e B l A a n s l o l i i r t p D o k h c t o i R w t o c n p e o C m p s i a u l t q A e , 9 w o 0 h 0 s 2 y t a h m g i r e y r p u o h C c o r © b
9 0 0 2 / 4 0 c 1 0 7 1 9 1 1 5 8 9