Method Statement for the Installation of Water Treatment Plant
Method Statement for the Installation of Water Treatment Plant
installation of
Thanks.
Method of Statement for Duct Installation
Description complète
Method of Statement for Duct Installation
Method Statement for Installation of TransformerFull description
MS AHU
Method Statement for Installation of Cable Trays
Method Statement for Installation of Cable TraysFull description
Method Statement for Installation of TransformerFull description
Method Statement for Installation of DBsFull description
Full description
okayFull description
cathode protection Method statement for installtion
bacaanFull description
This document describes the installation method for GRP tanks installations. especially needed by the consultants and to be provided by contractors.
Method Statement For Installation of Cold and Hot water Supply (Wet areas-Oce buildin!
0
"at e
" es c r i p ti on
# rep ar e
05 -0 3 - 16
Issued for Approval
AJ
C he c $e %p p r o& YH
AA
'
#urpose a)
To dene the method of installation of Hot and old !ater ""# "ipin$ %&stems a'ove-$round in toilet and (ithen areas of o*e 'uildin$+
Scope a)
)
This method statement is applia'le for Hot and old !ater ""# "ipin$ %&stems a'ove-$round emplo&in$ the approved materials+
*esponsibilities a)
,A, personnel main tas( is to ensure the .ualit& of /or( and materials delivered to site as per speiations dra/in$s manufaturers reommendations site instrutions and latest applia'le loal and international standards+
') The pro2et en$ineer-in-har$e is responsi'le for arr&in$ out detailed en$ineerin$ and manpo/er plannin$ /ithin the sope of ontrat preparation revie/ of shop dra/in$s and materials ta(e-o leadin$ to the prourement as per approval '& the onsultant+ ) %ite en$ineer is responsi'le for dail& site /or( oordination and 'riefs supervisors dail& tas(s to 'e underta(en+ d) %afet& o*er ensures and enfore appropriate measures to protet prevent and provide safet& to 'oth lives and properties on site+ e) %tore(eeper shall inspet materials delivered for an& dama$e and or disrepan& 'efore advisin$ ,A , for inspetion+ He shall 'e responsi'le for proper stora$e of the materials reeived on site+
+
"ocument , "rawins
a)
Approved %hop dra/in$s related to the /or(in$ area+
')
"ipin$ manufaturer doumentations atalo$ues+
./uipment0 1ools0 Material *e/uirements a)
Tools needed are4
""# fusion /eldin$ mahine onrete drillin$ mahine %et of spanners and sre/ drivers %aoldin$ ')
Wor$ #rocedure Soc$et Fusion 5ointin Method #reparation a)
Chec$ the temperature6 ;ne the so(et fusion is on he( the temperature /hih must ran$e 'et/een <53 = and <>? =+ This operation must 'e performed '& means of tempil sti(s+ The &ello/ one melts at <53 =+ The red one at <>? =+ The fusion temperature ran$es 'et/een <53 = and <>? = /hen the &ello/ pen melts and the red one does not melt the temperature is perfet for fusion+
')
Clean the heatin tools6 After he(in$ the heater 'ush temperature /ipe the heater 'ush /ith a lean loth+ This operation must 'e repeated after eah /eldin$+
)
Cut the pipe6 ut the pipe at ri$ht an$le if neessar& remove s/arf from inside+
d)
Chamfer the ##* pipes6 In hamferin$ the ends of pipes use suita'le or proper tools+
e)
Clean pipe and 7ttin6 lean the ttin$ inside and the pipe outside @the presene of dust an ause improper fusion)+ Fusion weldin6
a)
Mar$ the pipe6 ar( the pipe for depth of penetration into the heater 'ush and ttin$ @see ta'le)+ The mar( must remain visi'le under heatin$ and 2oinin$+
')
Heat pipe and 7ttin6 "ush the pipe and the ttin$ into the heatin$ tools+ ;ne pipe and ttin$ are hot @after the orret time) pull out pipe and ttin$ ver& slo/l&+
)
5oint pipe and 7ttin6 Joint the pipe ttin$ and push the pipe until it reahes the mar( @that has to sta& outside)+ 7urin$ the 2ointin$ time the /elded part of pipe and ttin$ assem'lies must remain ed /ithout an& rotation+ 7urin$ the oolin$ time the /elded part of pipe and ttin$ an 'e ad2usted until old+
d)
Fusion inspection6 The outer fusion seam must 'e inspeted+ The seam must 'e present all around the pipe+
Summary 8alue 1able6 "ipe inimum diameter !all mm Thi(ness mm
e)
Insert 7epth mm
Heatin$ Time se
Jointin$ oolin$ Time se Time min
<0
3+?
1?
6
?
<
<5
?+<
16
>
?
3
3<
5+?
1C
C
6
?
?0
6+>
<0
1<
6
?
50
C+?
<3
1C
6
5
63
10+5
<6
<5
C
6
>5
1<+5
30
C
C
B0
15+0
31
?0
10
C
110
1C+?
33
50
10
C
!hen all pipe and ttin$ assem'lies are read& installation /or(s ma& no/ start+
f) ar( all pipe lamp loation aordin$ to the reommended spain$ '& pipe manufaturer+ $)
!hen all supports anhors han$ers and pipes are read& pipes eretion ma& no/ proeed+
h)
"erform internal inspetion prior to endorsin$ to the onsultant for inspetion+
i)
;ne onsultant approved the installation proeed to pressure testin$ and one ompleted and inspeted /alls an proeed for plasterin$+