Descripción: Manual del juego X2: La Amenaza, en español.
Internal ‘Clockwise’ Rotating Central Assembly ‘X2’ Prototype Part Construction Workshop Schematics External ‘Counter - Clockwise’ Rotating Frame Work Assembly ‘X2’ Prototype Part Construction ...
matematicaFull description
holiDescripción completa
Full description
Descripción completa
Case Study Denso-Toyota
Precision engineering. Advanced design. The highest OEM quality. These are the exceptional qualities you’ll find in DENSO’s Engine Management Systems (EMS) ranges for the aftermarket.
OUTLINE OF ADDITIONAL DEVICES
Scala Evaluare anxietate
matematicaDescripción completa
Guide for the Sigma X2 firmware from former TCNISO. SOLD @ www.modempremodz.netFull description
Descripción: Separacion de materiales por medios densos
Working Procedure – on Nozzle Side Task 1 – Adjust Needle Opening Pressure (1)
Fasten injector on a vise with injector clamping tool. Loose nozzle nut (20)
Remove Calibration shim B23 (13), spring (14), spacer (12).
Install micrometer with extension probe 511012 on frame 970100. Place platform 511020 on frame 970100. Adjusting micrometer height by the hand wheel, then lock
the
moving
beam
by
the
handles.
Zero
micrometer on platform 511020. Caution: Pay close attention when adjusting micrometer mounting arm downward, to prevent micrometer damage.
3
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – on Nozzle Side Task 1 – Adjust Needle Opening Pressure (2)
Measure the thickness of shim B23 (13). (13) .
Fasten injector by using the matching holder on frame 970100.
Place spacer(12) and shim B23 (13) in injector cavity.
4
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – on Nozzle Side Task 1 – Adjust Needle Opening Pressure (3)
7. Place 10mm thickness gauge on the injector. injector. Adjusting the position of micrometer.
Zero
micrometer on the thickness gauge.
8. Remove the thickness gauge. Place spring(14) and spacer (15) in injector
9. Place 10mm thickness gauge on it.
Measure the top
of thickness gauge.
5
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – on Nozzle Side Task 1 – Adjust Needle Opening Pressure (4)
10. If the measured value does not meet requirement, replace calibration shim B23 with thickness indicated on PC screen
11. Fasten nozzle nut with torque 90Nm
6
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – Procedure – Solenoid Side Task 2 – Inspect Weariness of Valve Spacer (1)
Loose solenoid (1) from injector.
Remove calibration shim B44 2), armature(3), and ball(4)
Loose nut (5) by using special tool.
7
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – Procedure – Solenoid Side Task 2 – Inspect Weariness of Valve Spacer (2)
Remove valve spacer (6). Check the sealing surface in the center by using the microscope
The valve spacer with light weariness is still usable. Replace the severe worn one with new part.
8
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – Procedure – Solenoid Side Task 2 – Inspect Weariness of Valve Spacer (3)
Place The ball (4), with flat surface up, on the cavity at the end cavity of armature (3 ).
It is wrong to place the ball with spherical surface up.
9
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – Procedure – Solenoid Side Task 3 – Adjust Armature Lift (1)
Zero micrometer on platform 511020
Measure the thickness of shim B44
Install injector on the frame 970100 by using respective holder.
10
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – Procedure – Solenoid Side Task 3 – Adjust Armature Lift (2)
Extension rod 511011 and sleeve 97039 on micrometer.
Place calibration shim B44 (2) on injector
Place 1mm thickness gauge 511015 on shim B44
11
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – Procedure – Solenoid Side Task 3 – Adjust Armature Lift (3)
Zero micrometer on the thickness gauge
Remove the thickness gauge and then measure injector
If the measured value does not meet requirement, replace calibration shim B44 with thickness indicated on PC screen..
12
CRM-100 Common Rail Injector Measurement System
http://www.injectronix.com
Working Procedure – Procedure – Solenoid Side Task 3 – Adjust Armature Lift (4)
Using the shim B44 of correct thickness to assemble the injector. Fasten solenoid, torque 12-15Nm