1/114
Mapping of External Data (M14.0) Claro Peru
© Nokia Siemens Networks
DN0124783, issue 5-0
2/114
Mapping of External Data (M14.0) Claro Peru
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This document is not an official customer document and Nokia Siemens Networks does not take responsibility for any errors or omissions in this document. This document is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted. No part of this documentation may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity or performance of the mentioned hardware or software products are given “as is” and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA, that might arise from the use of this document or the information in it. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY APPLICABLE MANDATORY LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA SIEMENS NETWORKS RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE. This document and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2009. All rights reserved.
© Nokia Siemens Networks
DN0124783, issue 5-0
2/114
Mapping of External Data (M14.0) Claro Peru
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This document is not an official customer document and Nokia Siemens Networks does not take responsibility for any errors or omissions in this document. This document is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted. No part of this documentation may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity or performance of the mentioned hardware or software products are given “as is” and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA, that might arise from the use of this document or the information in it. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY APPLICABLE MANDATORY LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA SIEMENS NETWORKS RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE. This document and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2009. All rights reserved.
© Nokia Siemens Networks
DN0124783, issue 5-0
3/114
Contents
Contents Contents Contents ..................... ................................. ....................... ...................... ....................... ....................... ...................... ...................... ....................... ....................... ..............3 ...3 Summary of changes..........................................................................................................5 Changes Changes made between between issues issues 5-0 and 4-0.................. 4-0.................................... .................................. .................................. .................................5 ...............5
1
Introd Introduct uction....... ion........... ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ .....6 .6
2
Clear Clear codes codes set by statist statistics... ics....... ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ......7 ..7
3
BSSAP BSSAP mappin mapping.... g........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ .....8 .8
3.1.1 3.1.2 3.1.3 3.1.4
Base Station Station Subsystem Subsystem Applicati Application on Part (BSSAP) (BSSAP) / DTAP DTAP ............................... ...............................................8 ................8 Base Station Station Subsystem Subsystem Applicati Application on Part (BSSAP) (BSSAP) / DTAP DTAP ............................... .............................................13 ..............13 Location Location Services Services (LCS) (LCS) Cause Cause codes codes ............................... ................................................. .................................... ............................14 ..........14 Base Station Station Subsystem Subsystem Applicati Application on Part (BSSAP) (BSSAP) / BSSMAP BSSMAP ................................. ........................................15 .......15
4
MAP MAP mappin mapping g ........ ............ ........ ........ ........ ........ ......... ......... ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ......18 ..18
4.1.1 Mobile Mobile terminatin terminating g call call in the gateway gateway MSC .................................. .................................................. .................................. ...................18 .18 4.1.2 Internal Internal problems problems in the MAP protocol.............................. protocol................................................ .................................... ..............................18 ............18 4.1.3 Mobile Mobile terminatin terminating g call in the visitor visitor MSC .............................. ................................................ .................................... .........................19 .......19 4.1.4 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................19 ..19 4.1.5 Mobile Mobile originatin originating g call call in the visitor visitor MSC ............................... ................................................. .................................... .........................20 .......20 4.1.6 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................20 ..20 4.1.7 Location Location updating updating .................................. .................................................. .................................. .................................. .................................. .........................21 .......21 4.1.8 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................21 ..21 4.1.9 Mobile Mobile originatin originating g short short message message service service .............................. ................................................ .................................... .........................22 .......22 4.1.10 4.1.10 Mobile Mobile originatin originating g short message message servic service e in interworki interworking ng MSC...................... MSC........................................ ...................22 .22 4.1.10.1 4.1.10.1 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................22 ..22 4.1.11 4.1.11 Mobile Mobile originatin originating g short message message servic service e in visitor visitor MSC ...................... ........................................ ............................25 ..........25 4.1.11.1 4.1.11.1 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................25 ..25 4.1.12 4.1.12 Mobile Mobile terminati terminating ng short short message message servic service e .................................. .................................................. .................................. ......................28 ....28 4.1.13 4.1.13 Mobile Mobile terminati terminating ng short short message message servic service e in gateway gateway MSC MSC ............................... .............................................28 ..............28 4.1.13.1 4.1.13.1 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................28 ..28 4.1.14 4.1.14 Mobile Mobile terminati terminating ng short short message message servic service e in visitor visitor MSC MSC .................................. .................................................30 ...............30 4.1.14.1 4.1.14.1 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................30 ..30 4.1.15 4.1.15 Mobile Mobile origin originatin ating g unstructu unstructured red SS data data .................................. .................................................. .................................. .........................32 .......32 4.1.16 4.1.16 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................32 ..32 4.1.17 4.1.17 Mobile Mobile termina terminating ting unstructur unstructured ed SS data............... data ............................... .................................. .................................... .........................34 .......34 4.1.18 4.1.18 Internal Internal problems...... problems...................... .................................. .................................. .................................. .................................. .................................. ....................34 ..34 4.1.19 4.1.19 Subscrib Subscriber er locatio location n report report in VMSC VMSC ............................... ................................................. .................................... .................................36 ...............36
5
RANAP RANAP mappin mapping g ........ ............ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ......37 ..37
5.1.1
Radio Radio Access Access Network Network Applica Application tion Part (RANAP) (RANAP) ................................. .................................................. ...........................37 ..........37
6
SIP mappin mapping g ........ ............ ........ ........ ........ ........ ......... ......... ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........52 ....52
6.1.1
Signalli Signalling............... ng............................... .................................. .................................... .................................. .................................. .................................. .....................52 .....52
7
MEGAC MEGACO O mappin mapping g ........ ............ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ ........ .......59 ...59 © Nokia Siemens Networks
DN0124783, issue 5-0
4/114
Contents
7.1.1 7.1.2
Signalling..........................................................................................................................59 Cause code mapping........................................................................................................59
8
BICC mapping ......................................................................................................63
8.1.1 8.1.2 8.1.3
Signalling..........................................................................................................................63 Cause code mapping........................................................................................................63 Calling party category mapping ........................................................................................70
9
ISUP mapping.......................................................................................................73
9.1.1 9.1.2 9.1.3
Signalling..........................................................................................................................73 Cause code mapping........................................................................................................73 Calling party category mapping ........................................................................................79
10
DPNSS mapping...................................................................................................82
10.1.1 10.1.2 10.1.3
Signalling..........................................................................................................................82 Cause code mapping........................................................................................................82 Calling party category mapping ........................................................................................87
11
30B+D mapping....................................................................................................89
11.1.1 11.1.2 11.1.3
Signalling..........................................................................................................................89 Cause code mapping........................................................................................................89 Calling party category mapping ........................................................................................94
12
INAP mapping ......................................................................................................95
12.1.1 12.1.2 12.1.3
Signalling..........................................................................................................................95 Mapping table...................................................................................................................96 Calling party category mapping ......................................................................................103
13
CAMEL mapping ................................................................................................105
13.1.1 13.1.2 13.1.3
Signalling........................................................................................................................105 Mapping table.................................................................................................................106 Calling party category mapping ......................................................................................113
© Nokia Siemens Networks
DN0124783, issue 5-0
Summary of changes
5/114
Summary of changes Changes made between issues 5-0 and 4-0 The following sections have been modified in the document: • • • • • • • •
BSSAP mapping RANAP mapping SIP mapping MEGACO mapping BICC mapping ISUP mapping INAP mapping CAMEL mapping
© Nokia Siemens Networks
DN0124783, issue 5-0
6/114
Introduction
1 Introduction The document Mapping of External Data describes how cause codes are mapped from internal causes to external and vice versa. Internal causes are mapped to external causes of the incoming signalling by the MSC when the incoming and outgoing signalling systems differ, that is, adaptation must occur. In the node of the MSC/MSC server (MSS) system where the incoming and outgoing signalling systems are the same, the external cause code of the signalling system is transferred unchanged via the MSC. In this case a particular datatype, the so called postsack, is used to transmit the external cause code information transparently. The mapped internal cause code of the MSC is also used in the EOS analysis and statistics of the MSC. For more information, see Clear Codes
© Nokia Siemens Networks
DN0124783, issue 5-0
7/114
Clear codes set by statistics
2 Clear codes set by statistics This chapter describes the clear codes which are used when the statistics itself clears a call from the statistical call file.
INTERNAL CAUSE CODE
NUMBER
cd_t_call_record_rel_dur_calibr
0X00000102
Call file calibration clears the call which remains reserved in the statistics.
cd_t_forced_clear_of_a_call
0X0000070A
Statistics is asked to clear the call with a forced clear call message. The clear code is used unless the call has already been cleared.
cd_t_no_free_call_record_found
0X0000060C
The call id request is rejected because no free record can be found in the call file.
cd_t_unit_restarted
0X0000060E
The signalling unit is restarted, and the active calls during the restart are cleared from the statistics.
© Nokia Siemens Networks
DN0124783, issue 5-0
8/114
BSSAP mapping
3 BSSAP mapping 3.1.1 Base Station Subsystem Application Part (BSSAP) / DTAP All the codes are based on the following recommendations: 3GPP TS 24.008: Mobile radio interface Layer 3 specification; Core network protocols; Stage 3, CC-sublayer
Messages MESSAGES NUMBER (H/D) DISCONNECT 25 / 37 RELEASE 2D / 45 RELEASE COMPLETE 2A / 42 CM SERVICE ABORT 23 / 35 External cause codes EXTERNAL CAUSE CODES NUMBER (H/D) unalloc_num_c 1/1 no_rte_2_spec_trans_netwk_c 2/2 no_rte_2_dest_c 3/3 ch_unacceptable_c 6/6 call_delvd_in_est_ch_c 7/7 operator_det_barr_c 8/8 normal_call_clearing_c 10 / 16 user_busy_c 11 / 17 no_user_responding_c 12 / 18 no_answer_from_user_c 13 / 19 call_rejected_c 15 / 21 num_changed_c 16 / 22 non_selected_user_clrng_c 1A / 26 dest_out_of_order_c 1B / 27 invalid_num_fmt_c 1C / 28 facility_rejected_c 1D / 29 response_2_status_enq_c 1E / 30 normal_unspecified_c 1F / 31 no_circuit_or_ch_avail_c 22 / 34 netwk_out_of_order_c 26 / 38 temporary_failure_c 29 / 41 switch_equipment_congestn_c 2A / 42 access_info_discarded_c 2B / 43 reqd_ckt_or_ch_not_avail_c 2C / 44 resources_unavail_unspec_c 2F / 47 quality_of_service_unavail_c 31 / 49 req_facility_not_subscribed_c 32 / 50 incoming_calls_barr_in_cug_c 37 / 55
© Nokia Siemens Networks
DN0124783, issue 5-0
9/114
BSSAP mapping
bearer_cap_not_authorized_c 39 / 57 bearer_cap_pres_not_avail_c 3A / 58 service_or_opt_unavail_unspec_c 3F / 63 bearer_cap_not_implemtd_c 41 / 65 ch_typ_not_implemtd_c 42 / 66 acm_max_exceeded_c 44 / 68 reqd_fac_not_implemtd_c 45 / 69 only_restr_digital_info_avail_c 46 / 70 service_or_opt_not_implemtd_c 4F / 79 invld_call_ref_value_c 51 / 81 identified_ch_not_exist_c 52 / 82 susp_call_exist_but_not_this_c 53 / 83 call_id_in_use_c 54 / 84 no_call_suspended_c 55 / 85 call_wth_rqd_id_has_been_clrd_c 56 / 86 user_not_member_of_cug_c 57 / 87 incompat_dest_c 58 / 88 invld_trans_netwk_selectn_c 5B / 91 invld_msg_c 5F / 95 mand_info_elem_missing_c 60 / 96 msg_typ_not_implemtd_c 61 / 97 msg_not_compat_or_implemtd_c 62 / 98 info_elem_not_implemtd_c 63 / 99 invld_info_elem_contents_c 64 / 100 msg_not_compat_with_state_c 65 / 101 recvry_on_timer_expiry_c 66 / 102 protocol_error_c 6F / 111 interworking_unspec_c 7F / 127 other reasons
MAPPING TABLE MAPPING TABLE, internal cause to external cause INTERNAL CAUSE (H) (H/D) EXTERNAL CAUSE normal_end_of_the_call 0000 10 / 16 normal_call_clearing_c cl_a_onhook_answer_phase 030B 10 / 16 normal_call_clearing_c b_subscriber_busy 0005 11 / 17 user_busy_c cl_a_onhook_set_up_phase 030A 10 / 16 normal_call_clearing_c b_answer_time_out 0006 13 / 19 no_answer_from_user_c b_number_unused 0307 1/1 unalloc_num_c ac_meter_exceeded 0017 44 / 68 acm_max_exceeded_c clir_not_subscribed 0C0C 32 / 50 req_facility_not_subscribed_c (ph1) 32 / 50+ diagn. req_facility_not_subscribed_c 06 not_subscribed_c (ph2) subs_sig_protocol_error 0D04 6F / 111 protocol_error_c address_incomplete 0B17 1C / 28 invalid_num_fmt_c → → → → → → → → →
→ →
© Nokia Siemens Networks
DN0124783, issue 5-0
BSSAP mapping
10/114
prohibited_dialling circuit_congestion b_onhook_time_out radio_if_congestion terminal_switch_off absent_subscriber no_paging_response call_rejected outgoing_circ_congestion subs_signa_msg_content_err gsm_erh408_prot_timer_exp ct_recall_time_out call_waiting_time_out serv_facil_activa_restrict bc_not_presently_available serv_facil_not_implemented inconsist_between_a_and_b subs_signa_msg_format_err b_calls_restricted call_diversion_barring cug_reject
0C01 080F 030C 0205 0318 0010 0012 0206 0804 0D00 0D08 0013 0007 0C09 0C0D 0D03 0C0B 0D01 0306 0315 0310
dte_uncontrolled nae_error service_unavailable service_incompatible subscriber_congestion terminal_congestion trunk_circ_protocol_error address_complete_time_out restrict_in_out_direction oper_restr_in_out_direct
0B21 0B20 0B18 0B19 0207 081A 0A04 0A09 0300 0301
b_line_out_of_service tele_serv_not_prov bearer_serv_not_prov unidentified_subscriber b_number_changed facility_not_supported interw_unit_congestion map_congestion overload_congestion clear_request_rec_out_crct alternative_routing_1
0304 0312 0311 0314 0308 0810 0401 040C 060B 0202 1015
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → →
→ → → → → → → → → →
→ → → → → → → → → → →
1/1 2C / 44 10 / 16 22 / 34 10 / 16 12 / 18 12 / 18 15 / 21 2C / 44 64 / 100 66 / 102 13 / 19 13 / 19 32 / 50 3A / 58 4F / 79 58 / 88 5F / 95 15 / 21 7F / 127 1D / 29 1D / 29+ diagn.05 3F / 63 1C / 28 2F / 47 3F / 63 11 / 17 2C / 44 6F / 111 66 / 102 15 / 21 15 / 21 08 / 08 1B / 27 32 / 50 32 / 50 1/1 16 / 22 45 / 69 2A / 42 2A / 42 2A / 42 10 / 16 2C / 44
unalloc_num_c reqd_ckt_or_ch_not_avail_c normal_call_clearing_c no_circuit_or_ch_avail_c normal_call_clearing_c no_user_responding_c no_user_responding_c call_rejected_c reqd_ckt_or_ch_not_avail_c invld_info_elem_contents_c recvry_on_timer_expiry_c no_answer_from_user_c no_answer_from_user_c req_facility_not_subscribed_c bearer_cap_pres_not_avail_c service_or_opt_not_implemtd_c incompat_dest_c invld_msg_c call_rejected_c interworking_unspec_c facility_rejected_c (ph1) facility_rejected_c cug_call_fail_uns_c (ph2) service_or_opt_unavail_unspec_c invalid_num_fmt_c resources_unavail_unspec_c service_or_opt_unavail_unspec_ user_busy_c reqd_ckt_or_ch_not_avail_c protocol_error_c recvry_on_timer_expiry_c call_rejected_c call_rejected_c (ph1) operator_det_barr_c (ph2) dest_out_of_order_c req_facility_not_subscribed_c req_facility_not_subscribed_c unalloc_num_c num_changed_c reqd_fac_not_implemtd_c switch_equipment_congestn_c switch_equipment_congestn_c switch_equipment_congestn_c normal_call_clearing_c reqd_ckt_or_ch_not_avail_c DN0124783, issue 5-0
BSSAP mapping
11/114
alternative_routing_2 1016 alternative_routing_3 1017 aocc_charging_error 0D06 b_modem_subs_busy 101F b_modem_subs_unobtainable 1020 digital_path_not_provided 0A0C cf_ms_not_reach_no_notif_a 1010 cf_ms_busy_notif_to_a 1011 cf_ms_busy_no_notif_to_a 1012 cf_ms_not_reply_notif_to_a 1013 cf_ms_not_reply_no_notif_a 1014 circuit_group_congestion 0814 n_unallocated_number 0817 n_line_out_of_service 0818 n_subscriber_nbr_changed 0819 illegal_subscriber_station 0319 no_user_responding 0D07 illegal_subscriber 0313 r2_signal_pause_time_out 0807 r2_sign_backwards_time_out 0808 r2_err_signl_from_out_crct 0809 r2_err_signal_from_in_crct 080A cug_rec_icb 031A
→ → → → → → → → → → → → → → → → → → → → → → →
cug_rej_not_member
031C
→
cug_rej_ocb
031D
→
cug_rej_ind_not_comp_bs
031E
→
cug_rej_bs_violation
031F
→
cug_rej_ss_violation
0320
→
cug_rej_no_cug_selected
0321
→
cug_rej_unknown_cug_ind
0322
→
© Nokia Siemens Networks
2C / 44 2C / 44 66 / 102 11 / 17 12 / 18 41 / 65 10 / 16 10 / 16 10 / 16 10 / 16 10 / 16 22 / 34 1/1 1B / 27 16 / 22 15 / 21 12 / 18 1B / 27 66 / 102 66 / 102 1B / 27 1B / 27 3F / 63 37 / 55+ diagn.05 5F / 95 57 / 87+ diagn.05 1D / 29 1D / 29+ diagn.01 1D / 29 1D / 29+ diagn.04 1D / 29 1D / 29+ diagn.04 1D / 29 1D / 29+ diagn.05 1D / 29 1D / 29+ diagn.02 1D / 29 1D / 29+
reqd_ckt_or_ch_not_avail_c reqd_ckt_or_ch_not_avail_c recvry_on_timer_expiry_c user_busy_c no_user_responding_c bearer_cap_not_implemtd_c normal_call_clearing_c normal_call_clearing_c normal_call_clearing_c normal_call_clearing_c normal_call_clearing_c no_circuit_or_ch_avail_c unalloc_num_c dest_out_of_order_c num_changed_c call_rejected_c no_user_responding_c dest_out_of_order_c recvry_on_timer_expiry_c recvry_on_timer_expiry_c dest_out_of_order_c dest_out_of_order_c service_or_opt_unavail_unspec_c (ph1) incoming_calls_barr_in_cug_c cug_call_fail_uns_c (ph2) invld_msg_c (ph1) user_not_member_of_cug_c cug_call_fail_uns_c (ph2) facility_rejected_c (ph1) facility_rejected_c og_barr_within_cug_c(ph2) facility_rejected_c (ph1) facility_rejected_c ind_incomp_w_bas_s_c (ph2) facility_rejected_c (ph1) facility_rejected_c ind_incomp_w_bas_s_c (ph2) facility_rejected_c (ph1) facility_rejected_c cug_call_fail_uns_c (ph2) facility_rejected_c (ph1) facility_rejected_c no_cug_selected_c (ph2) facility_rejected_c (ph1) facility_rejected_c
DN0124783, issue 5-0
BSSAP mapping
12/114
serv_facil_usage_restrict configuration_error traffic_type_congestion no_free_call_record_found switching_equ_congestion b_access_barred congestion_send_info_tone b_busy_ccbs_act_possible
0C0A 070E 040A 060C 0813 0815 0816 0026
b_busy_ccbs_not_possible
0022
facility_rejected facility_not_avail_on_outr call_rerouting_restrict req_channel_not_available multicall_usage_rejected insufficient_dialling hunt_serv_rel b_number_overflow bor_configuration_failure mgw_internal_failure congestion_on_mgw anonymous_c_rej_cli_not_av anonymous_call_reject no_route_to_destination call_interrupt_in_reg_ana setup_normal_eoc All others
0D0F 0715 0880 071B 0323 0C02 0027 0408 0106 0885 0843 0036 0220 0A0D 0706 0031
→ → → → → → → →
→
→ → → → → → → → → → → → → → → → →
diagn.03 3F / 63 2F / 47 2F / 47 2A / 42 2A / 42 15 / 21 15 / 21 11 / 17 11 / 17+ diagn.07 11 / 17 11 / 17+ diagn.08 1D / 29 2F / 47 2C / 44 2C / 44 5F / 95 1C / 28 10 / 16 1C / 28 15 / 21 2F / 47 2F / 47 15 / 21 15 / 21 3/3 4F / 79 10 / 16 1F / 31
unknown_cug_index_c (ph2) service_or_opt_unavail_unspec_c resources_unavail_unspec_c resources_unavail_unspec_c switch_equipment_congestn_c switch_equipment_congestn_c call_rejected_c call_rejected_c user_busy_c (ph1) user_busy_c CCBS possible (ph2) user_busy_c (ph1) user_busy_c CCBS not possible (ph2) facility_rejected_c resources_unavail_unspec_c reqd_ckt_or_ch_not_avail_c reqd_ckt_or_ch_not_avail_c invld_msg_c invalid_num_fmt_c normal_call_clearing_c invalid_num_fmt_c call_rejected_c resources_unavail_unspec_c resources_unavail_unspec_c call_rejected_c call_rejected_c no_rte_2_dest_c service_or_opt_not_implemtd_c normal_call_clearing_c normal_unspecified_c
MAPPING TABLE MAPPING TABLE, external cause code to internal cause code EXTERNAL CAUSE H/D H INTERNAL CAUSE normal_call_clearing_c 10 / 16 0000 normal_end_of_the_call user_busy_c 11 / 17 0005 b_subscriber_busy no_user_responding_c 12 / 18 0D07 no_user_responding no_answer_from_user_c 13 / 19 0006 b_answer_time_out call_rejected_c 15 / 21 0206 call_rejected facility_rejected_c 1D / 29 0D0F facility_rejected temporary_failure_c 29 / 41 080D out_circuit_out_of_order reqd_ckt_or_ch_not_avail_c 2C / 44 0B1E radio_resource_unavailable resources_unavail_unspec_c 2F / 47 0B1E radio_resource_unavailable req_facility_not_subscribed_c 32 / 50 0C09 serv_facil_activa_restrict → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
13/114
BSSAP mapping
bearer_cap_not_authorized_c 39 / 57 bearer_cap_pres_not_avail_c 3A / 58 service_or_opt_unavail_unspec_c 3F / 63 bearer_cap_not_implemtd_c 41 / 65 acm_max_exceeded_c 44 / 68 reqd_fac_not_implemtd_c 45 / 69 service_or_opt_not_implemtd_c 4F / 79 invld_call_ref_value_c 51 / 81 incompat_dest_c 58 / 88 invld_msg_c 5F / 95 mand_info_elem_missing_c 60 / 96 msg_typ_not_implemtd_c 61 / 97 msg_not_compat_or_implemtd_c 62 / 98 info_elem_not_implemtd_c 63 / 99 invld_info_elem_contents_c 64 / 100 msg_not_compat_with_state_c 65 / 101 recvry_on_timer_expiry_c 66 / 102 protocol_error_c 6F / 111 interworking_unspec_c 7F / 127 All others
→ → → → → → → → → → → → → → → → → → → →
0C09 serv_facil_activa_restrict 0C0D bc_not_presently_available 0C0A serv_facil_usage_restrict 0D03 serv_facil_not_implemented 0017 ac_meter_exceeded 0D03 serv_facil_not_implemented 0D03 serv_facil_not_implemented 0D00 subs_signa_msg_content_err 0C0B inconsist_between_a_and_b 0D00 subs_signa_msg_content_err 0D01 subs_signa_msg_format_err 0D0D msg_not_cmptbl_or_impl 0D04 subs_sig_protocol_error 0D01 subs_signa_msg_format_err 0D00 subs_signa_msg_content_err 0D04 subs_sig_protocol_error 0D08 gsm_erh408_prot_timer_exp 0D04 subs_sig_protocol_error 0A03 interworking_failed 0015 normal_unspecified
When a normal clearing is received from the A-subscriber before the Setup phase (CM SERVICE ABORT) or in the Setup phase (DISCONNECT, RELEASE or RELEASE COMPLETE with the cause code 'Normal call clearing'), the internal cause 0x30A "cl_a_onhook_set_up_phase" is set. When a normal clearing is received from the A-subscriber in the Answer phase (DISCONNECT, RELEASE or RELEASE COMPLETE with the cause code "Normal call clearing"), the internal cause 0x30B 'cl_a_onhook_answer_phase' is set.
3.1.2 Base Station Subsystem Application Part (BSSAP) / DTAP All the BSSAP codes are based on the following recommendations: 3GPP TS 24.008: Mobile radio interface Layer 3 specification; Core network protocols; Stage 3, MM-sublayer
Messages MESSAGES NUMBER (H/D) LOCATION UPDATING REJECT 08 / 08 CM SERVICE REJECT 22 / 34 External cause codes EXTERNAL CAUSE CODES NUMBER (H/D) mm_cause_t_imsi_unknwn_in_hlr_c 02 / 02 mm_cause_t_illegal_ms_c 03 / 03 mm_cause_t_imsi_unknwn_in_vlr_c 04 / 04 mm_cause_t_illegal_me_c 06 / 06 mm_cause_t_plmn_not_allow_c 0b / 11
© Nokia Siemens Networks
DN0124783, issue 5-0
BSSAP mapping
14/114
mm_cause_t_loc_area_not_allow_c 0c / 12 mm_cause_t_nat_roam_not_allow_c 0d / 13 mm_cause_t_no_suit_cells_in_la_c 0f / 15 mm_cause_t_network_failure_c 11 / 17 mm_cause_t_congestion_c 16 / 22 mm_cause_t_req_serv_not_sbscr_c 21 / 33
MAPPING TABLE MAPPING TABLE, internal cause code to external cause code INTERNAL CAUSE (H) (H/D) EXTERNAL CAUSE b_number_unused 0307 02 / 02 imsi_unknwn_in_hlr_c illegal_subscriber 0313 03 / 03 illegal_ms_c unidentified_subscriber 0314 04 / 04 imsi_unknwn_in_vlr_c illegal_subscriber_station 0319 03 / 03 illegal_ms_c (ph1) 06 / 06 illegal_me_c (ph2) plmn_not_allowed 0D52 0B / 11 plmn_not_allow_c exc_acc_non_solsa_ms 0254 0B / 11 plmn_not_allow_c lac_not_allowed 0D51 0C / 12 loc_area_not_allow_c subs_sig_protocol_error 0D04 0C / 12 loc_area_not_allow_c roaming_not_allowed 040E 0C / 12 loc_area_not_allow_c (ph1) 0D / 13 nat_roam_not_allow_c (ph2) overload_congestion 060B 16 / 22 congestion_c no_suitable_cells_in_la 0420 0C / 12 loc_area_not_allow_c (ph1& ph2) 0F / 15 no_suit_cells_in_la_c (ph3) serv_facil_usage_restrict 0C0A 21 / 33 req_serv_not_sbscr_c susp_lu_cancel_during_lu 0425 0F / 15 no_suit_cells_in_la_c All others 11 / 17 network_failure_c → → → → →
→ → → → →
→ →
→ → →
3.1.3 Location Services (LCS) Cause codes All the BSSAP codes are based on the following recommendations: 3GPP TS 49.031 Location Services (LCS); Base Station System Application Part LCS Extension (BSSAP-LE)
LCS cause code messages MESSAGES NUMBER (H/D) PERFORM_LOCATION_RESPONSE 2D / 45 LCS external cause codes EXTERNAL CAUSE CODES NUMBER (H/D) lcs_cause_t_unspecified_c 00 / 00 lcs_cause_t_system_failure_c 01 / 01 lcs_cause_t_protocol_error_c 02 / 02 lcs_cause_t_data_miss_in_req_c 03 / 03 lcs_cause_t_unexpected_data_c 04 / 04 © Nokia Siemens Networks
DN0124783, issue 5-0
BSSAP mapping
15/114
lcs_cause_t_pos_meth_failure_c 05 / 05 lcs_cause_t_target_ms_unreac_c 06 / 06 lcs_cause_t_loc_req_aborted_c 07 / 07 lcs_cause_t_facility_notsupp_c 08 / 08 lcs_cause_t_inter_bsc_ho_on_c 09 / 09 lcs_cause_t_intra_bsc_ho_comp_c 0A / 10 lcs_cause_t_congestion_c 0B / 11
MAPPING TABLE MAPPING TABLE, external cause code to internal cause code EXTERNAL CAUSE INTERNAL CAUSE unspecified_c 00 / 00 0000 normal_end_of_the_call system_failure_c 01 / 01 103D position_method_failure protocol_error_c 02 / 02 103D position_method_failure data_miss_in_req_c 03 / 03 103D position_method_failure unexpected_data_c 04 / 04 103D position_method_failure pos_meth_failure_c 05 / 05 103D position_method_failure target_ms_unreac_c 06 / 06 103D position_method_failure loc_req_aborted_c 07 / 07 103D position_method_failure facility_notsupp_c 08 / 08 103D position_method_failure inter_bsc_ho_on_c 09 / 09 103D position_method_failure intra_bsc_ho_comp_c 0A / 10 103D position_method_failure congestion_c 0B / 11 103D position_method_failure → → → → → → → → → → → → →
3.1.4 Base Station Subsystem Application Part (BSSAP) / BSSMAP All the BSSAP codes are based on the following recommendations: 3GPP TS 48.008 Mobile Switching Centre - Base Station system (MSC-BSS) interface; Layer 3 specification
Messages MESSAGES NUMBER (H/D) CLEAR REQUEST 22 / 34 ASSIGNMENT FAILURE 03 / 03 External cause codes EXTERNAL CAUSE CODES NUMBER (H/D) bm_cause_t_radio_if_mess_fail_c 0 / 0 bm_cause_t_radio_if_fail_c 1/1 bm_cause_t_uplink_quality_c 2/2 bm_cause_t_uplink_strength_c 3/3 bm_cause_t_downlink_quality_c 4/4 bm_cause_t_downlink_strength_c 5 / 5 bm_cause_t_distance_c 6/6
© Nokia Siemens Networks
DN0124783, issue 5-0
16/114
BSSAP mapping
bm_cause_t_o_and_m_inter_c 7/7 bm_cause_t_resp_to_msc_invoc_c 8 / 8 bm_cause_t_call_control_c 9/9 bm_cause_t_r_if_f_rev_to_old_c A / 10 bm_cause_t_handover_succ_c B / 11 bm_cause_t_better_cell_c C / 12 bm_cause_t_directed_retry_c D / 13 bm_cause_t_traffic_c F / 15 bm_cause_t_red_load_serv_cell_c 10 / 16 bm_cause_t_tr_l_higher_t_cell_c 11 / 17 bm_cause_t_reloc_triggered_c 12 / 18 bm_cause_t_resp_to_int_ho_c 16 / 22 bm_cause_t_int_ho_enq_rej_c 17 / 23 bm_cause_t_equipment_fail_c 20 / 32 bm_cause_t_no_radio_res_avail_c 21 / 33 bm_cause_t_req_terr_res_unava_c 22 / 34 bm_cause_t_ccch_overload_c 23 / 35 bm_cause_t_processor_overload_c 24 / 36 bm_cause_t_bss_not_equipped_c 25 / 37 bm_cause_t_ms_not_equipped_c 26 / 38 bm_cause_t_invalid_cell_c 27 / 39 bm_cause_t_traffic_load_c 28 / 40 bm_cause_t_preemption_c 29 / 41 bm_cause_t_tr_cod_rat_ad_unav_c 30 / 48 bm_cause_t_crct_pool_mismatch_c 31 / 49 bm_cause_t_switch_crct_pool_c 32 / 50 bm_cause_t_req_sp_ver_unavail_c 33 / 51 bm_cause_t_req_codec_unavail_c 35 / 53 bm_cause_t_req_a_if_unavail_c 36 / 54 bm_cause_t_red_level_not_adeq_c 3E / 62 bm_cause_t_req_re_lev_not_sup_c 3F / 63 bm_cause_t_ciph_alg_not_supp_c 40 / 64 bm_cause_t_geran_iu_failure_c 41 / 65 bm_cause_t_reloc_n_s_due_pues_c42 / 66 bm_cause_t_req_codec_not_sup_c 44 / 68 bm_cause_t_req_a_if_not_sup_c 45 / 69 bm_cause_t_terr_chan_alr_allc_c 50 / 80 bm_cause_t_invalid_msg_cont_c 51 / 81 bm_cause_t_inf_ele_or_fie_mis_c 52 / 82 bm_cause_t_incorrect_value_c 53 / 83 bm_cause_t_unknwn_msg_type_c 54 / 84 bm_cause_t_unknwn_info_elem_c 55 / 85 bm_cause_t_call_id_alloc_c 57 / 87 bm_cause_t_prot_err_b_bsc_msc_c 60 / 96
© Nokia Siemens Networks
DN0124783, issue 5-0
BSSAP mapping
17/114
MAPPING TABLE MAPPING TABLE, external cause codes to internal cause codes EXTERNAL CAUSE (H/D) (H) INTERNAL CAUSE radio_if_mess_fail_c 0 / 0 0B1B radio_if_msg_failure radio_if_fail_c 1/1 0B13 radio_if_failure o_and_m_inter_c 7/7 0B1D n_o_and_m_intervention resp_to_msc_invoc_c 8 / 8 0011 operator_priority_access r_if_f_rev_to_old_c A / 10 0B1C radio_if_fail_rev_to_old directed_retry_c D / 13 0B1C radio_if_fail_rev_to_old equipment_fail_c 20 / 32 0B16 remote_equipment_failure no_radio_res_avail_c 21 / 33 0205 radio_if_congestion req_terr_res_unava_c 22 / 34 0B1F req_terr_resource_unavail ccch_overload_c 23 / 35 081F n_overload_congestion processor_overload_c 24 / 36 081F n_overload_congestion bss_not_equipped_c 25 / 37 0B16 remote_equipment_failure ms_not_equipped_c 26 / 38 0B16 remote_equipment_failure preemption_c 29 / 41 0011 operator_priority_access tr_cod_rat_ad_unav_c 30 / 48 0B16 remote_equipment_failure lsa_not_allowed_c 34 / 52 0253 lsa_not_allowed req_codec_unavail_c 35 / 53 0B45 req_cdc_type_unavailable req_a_if_unavail_c 36 / 54 0B46 req_a_int_type_unavailable ciph_alg_not_supp_c 40 / 64 0B15 ciphering_not_succeeded reloc_n_s_due_pues_c42 / 66 0810 facility_not_supported req_codec_not_sup_c 44 / 68 0B47 req_cdc_type_not_sup req_a_if_not_sup_c 45 / 69 0B48 req_a_int_type_not_sup terr_chan_alr_allc_c 50 / 80 0B1F req_terr_resource_unavail call_id_alloc_c 57 / 87 0B44 call_id_already_alloc Any other value 0B1A bssmap_protocol_error → → → → → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
18/114
4 MAP mapping SIGNALLING: Mobile application part (MAP) GSM Recommendation 09.02: 3GPP TS 09.02 Mobile Application Part (MAP) Specification.
4.1.1 Mobile terminating call in the gateway MSC Mapping table for received error causes from HLR UnknownSubscriber 0x1 B_NUMBER_UNUSED 0x307 TeleserviceNotProvisioned 0xB TELE_SERV_NOT_PROV 0x312 BearerServiceNotProvisioned 0xA BEARER_NOT_PROV 0x311 AbsentSubscriber 0x1B ABSENT_SUBSCRIBER 0x10 CallBarred Ss-barred 0xD B_CALLS_RESTRICTED 0x306 CallBarred Operator-barred 0xD B_LINE_OUT_OF_SERVICE 0X304 CugReject No additional info from nw 0xF CUG_REJECT 0x310 CugReject IncomingCalls-BarredW ithCug 0xF CUG_REJ_ICB 0x31A CugReject SubscriberNotMemberOfCug 0xF CUG_REJ_NOT_MEMBER 0x31C CugReject RequestedBasicServiceViolates0xF CUG_REJ_BS_VIOLATION 0x31F CugConstraints CugReject CalledPartySs-Interaction-Violation 0xF CUG_REJ_SS_VIOLATION 0x320 ForwardingViolation 0xE CALL_DIVERSION_BARRING 0x315 FacilityNotSupported 0x15 FACILITY_NOT_SUPPORTED 0x810 NumberChanged 0x2C B_NUMBER_CHANGED 0x308 SystemFailure 0x22 NETWORK_FAILURE 0x811 UnexpectedDataValue 0x24 MAP_FAILURE 0x812 DataMissing 0x23 MAP_FAILURE 0x812 BusySubscriber ccbs-Possible from nw 0x2DB_BUSY_CCBS_POSSIBLE 0x21 BusySubscriber no ccbs-Possible from nw 0x2DB_BUSY_CCBS_NOT_POSSIBLE 0x22
4.1.2 Internal problems in the MAP protocol MAP_FAILURE 0x812 MAP sets the cause code in the following situations: •
• • • • •
If the HLR enquiry analysis result global title or the signalling point code has no routing to the HLR. If abort has been received from the HLR. If reject has been received from the HLR. If there is resource limitation in TCAP. If an unexpected message has been received from TCAP. If MAP detects that remote end has violated the MAP recommendation.
© Nokia Siemens Networks
DN0124783, issue 5-0
19/114
MAP mapping
NO_HLR_RESPONSE 0x81B If the GMSC does not receive a response from the HLR (operation timer expires), MAP sets the cause code no_hlr_response.
OVERLOAD_CONGESTION 0x60B If MAP detects that there are too many unhandled messages in the CCSU when the HLR enquiry is started, MAP rejects the HLR enquiry and sets this release code.
MAP_CONGESTION 0x40C If MAP cannot handle the HLR enquiry because it has no resources available to handle the service, MAP rejects the HLR enquiry and sets this release code.
ERR_REQ_FROM_CO_PROCESS 0x405 If the user sends an illegal parameter value in the request to the MAP, MAP rejects the HLR enquiry and sets this release code.
CUG_REJECT 0x310 The SendRoutingInfo operation is rejected by MAP in the VLR, because CUG information cannot be supported with the current MAP version.
4.1.3 Mobile terminating call in the visitor MSC 4.1.4 Internal problems ERR_REQ_FROM_CO_PROCESS 0x405 The Mobile Application Part MCS Program Block (MMCPRB) sets this error cause if the co-process tries to send a message to the MMCPRB resource which is no longer reserved for the service.
UNALLOCATED_ROAMING_NUMBER 0x40D The MMCPRB sets this error cause if it cannot find the VLRU pair based on the roaming number.
ERR_ANSWER_FROM_CO_PROCESS 0x407 The MMCPRB sets this error cause if it receives an IMEI enquiry response from the A interface although IMEI checking is not activated.
NO_RESPONSE_FROM_CO_PROCES 0x603 The MMCPRB sets this error cause if the time control expires for the co-process (not for VLR resource) response.
© Nokia Siemens Networks
DN0124783, issue 5-0
20/114
MAP mapping
NO_VLR_RESPONSE 0x81C The MMCPRB sets this error cause if the time control expires for the VLR resource response.
CRIS_MODE_OUT_RESTRICTION 0xC The MMCPRB sets this error cause if the call setup is interrupted due to the exchange operation mode.
FILE_ERROR 0x509 The MMCPRB sets this error cause if the exchange operation mode cannot be solved.
CF_PNS 0x1025 The MMCPRB sets this error cause if B-subscriber belonging to PNP group is busy and the call forwarding is activated.
NO_RESOURCE_FOR_CALL 0x719 The MMCPRB sets this error cause if it has no resources available to handle the VLR enquiry.
NETWORK_FAILURE 0x811 The MMCPRB sets this error cause if subscriber identification is performed after authentication and the fetched IMSI differs from the IMSI stored to the VLR. Furthermore this error cause is used with additional clear situation information to inform the VLR resource that the TMSI reallocation response shall be still waited for after co-process aborts.
4.1.5 Mobile originating call in the visitor MSC 4.1.6 Internal problems ERR_REQ_FROM_CO_PROCESS 0x405 The MMCPRB sets this error cause if co-process tries to send a message to the MMCPRB resource that is no longer reserved for the service.
NO_RESOURCE_FOR_CALL 0x719 The MMCPRB sets this error cause if it has no resources available to handle the VLR enquiry.
FACILITY_NOT_SUPPORTED 0x810 The MMCPRB sets this error cause if the access management data enquiry from the VLR is started with an incorrect service_type.
© Nokia Siemens Networks
DN0124783, issue 5-0
21/114
MAP mapping
OVERLOAD_CONGESTION 0x60B The MMCPRB sets this error cause if overload control does not give permission to continue the access management data enquiry from the VLR when identification is performed before authentication.
NO_VLR_RESPONSE 0x81C The MMCPRB sets this error cause if the time control expires for the VLR resource response.
NO_RESPONSE_FROM_CO_PROCES 0x603 The MMCPRB sets this error cause if the time control expires for the co-process (not for VLR resource) response.
NETWORK_FAILURE 0x811 The MMCPRB sets this error cause with additional clear situation information to inform the VLR resource that the TMSI reallocation response shall be still waited for after co-process abort.
ILLEGAL_SUBSCRIBER 0x313 The MMCPRB sets this error cause if subscriber identification is performed after authentication and the fetched IMSI differs from the IMSI stored to the VLR.
4.1.7 Location updating MTAPRB: Mapping table for received error causes from HLR UnknownSubscriber 0x1 B_NUMBER_UNUSED 0x307 RoamingNotAllowed 0x8 ROAMING_NOT_ALLOWED0x40E SystemFailure 0x22NETWORK_FAILURE 0x811 DataMissing 0x23 MAP_FAILURE 0x812 UnexpectedDataValue0x24MAP_FAILURE 0x812
4.1.8 Internal problems ERR_REQ_FROM_CO_PROCESS 0x405 The MMCPRB sets this error cause if the co-process tries to send a message to the MMCPRB resource that is no longer reserved for the service.
MAP_CONGESTION 0x40C The MMCPRB sets this error cause if it has no resources available to handle the VLR enquiry.
NO_RESPONSE_FROM_CO_PROCES 0x603 The MMCPRB sets this error cause if the time control expires for the TMSI reallocation response from the A interface.
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
22/114
OVERLOAD_CONGESTION 0x60B The MMCPRB sets this error cause if overload control does not give permission to continue the location update when identification is performed before authentication.
ILLEGAL_SUBSCRIBER 0x313 The MMCPRB sets this error cause if subscriber identification is done after authentication and the fetched IMSI differs from the IMSI stored to the VLR.
4.1.9 Mobile originating short message service 4.1.10
Mobile originating short message service in interworking MSC
SMHPRB: Mapping table for received error causes from SMSC MsNotSubscriber 103A_NOT_SC_SUBSCRIBER 0x250 SCCongestion 101 SC_CONGESTION 0x850 UnknownApplEntityTitle200 SUBS_SIGN_INVALID_SM 0xD50 InvalidSMEntityAddress 102 SUBS_SIGN_INVALID_SM 0xD50 other error cause ERR_REQ_FROM_CO_PROCESS0x405
4.1.10.1
Internal problems
ERR_ANSWER_FROM_CO_PROCESS 0x407 SMHPRB sets this clear code in the following situations:
6000 SMSC address analyses fails in the GSAPRB inquiry.
MAP_CONGESTION 0x40C SMHPRB sets this clear code in the following situations:
0002 Service request has rejected because of MO-SM IWMSC hand reservation failure. 0004 Service request has rejected because of AlertSC hand reservation failure.
NO_RESPONSE_FROM_CO_PROCESS 0x603 SMHPRB sets this clear code in the following situations:
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
23/114
4000,6003 Hand process has not received the dialogue start message from the master process. 4001,6000 No response from GSAPRB when waiting for the GSAPRB inquiry response. 4002,6001 No response from O7AMAN when waiting for the O7AMAN inquiry response. 4003,6002 No response from OSHORT when waiting for the OSI connection create inquiry response. 4005 No response from OSHORT when waiting for the forwarding of SM response from SMSC. 4006 No response from MTAPRB when waiting for the hand ID in forwarding of SM from IWMSC. 4007 No response from MTAPRB when waiting for the forwarding of the SM response from IWMSC. 6004 No response from OSHORT when waiting for the AlertSC response from SMSC.
UNIT_RESTARTED 0x60E SMHPRB sets this clear code in the following situations:
4000,6000 Address of the O7AMAN is unknown. This may have been caused by the restart of the CM unit.
OVERLOAD_CONGESTION 0x60B SMHPRB sets this clear code in the following situations:
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
24/114
4000 No response from the GCGPRO when waiting for the overload checking response.
NETWORK_FAILURE NETWORK_FAILURE 0x811 SMHPRB sets this clear code in the following situations:
4000, 6000 Opening of OSI connection fails. This may have been caused by the changing of the SMSC analysis during this SM or the links between the MSC and SMSC have gone down. 4001, 6002 Opening of OSI connection fails because all the links between the MSC and SMSC have gone down. 4002, 6003 Saving of the SMSC address to the connection table fails. There is already the maximum number of SMSC addresses and none of them is in idle state. 6001 Negative response from the SMSC.
SUBS_SIGN_INVALID_SM SUBS_SIGN_INVALID_SM 0xD50 SMHPRB sets this clear code in the following situations:
4000 Illegal message type indicator in the user info from the VMSC. 4001 No application entity name from the GSAPRB inquiry. 4004 User info length from the VMSC is too short. 4005 User info length from the VMSC exceeds the maximum legal length.
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
25/114
4.1.1 4.1.11 1
Mobile Mobile orig origina inatin ting g short short messag message e servi service ce in in visit visitor or MSC MSC
SMHPRB: Mapping table for received error causes from interworking MSC Deli Delive very ryFa Fail ilur ureS eSCC CCon onge gest stio ion n 0x20 0x20 SC_CONGESTION 0x850 0x04 Deliv Delivery eryFai Failur lureM eMSNo SNotSu tSubsc bscrib riber er 0x20 0x20 A_NOT_SC_SUBSCRIBER A_NOT_SC_SUBSCRIBER 0x250 0x06 DeliveryFailure DeliveryFailure other than mentioned 0x20 SUBS_SIGN_INVALID_SM SUBS_SIGN_INVALID_SM 0xD50 0xD50 MTAPRB: Mapping table for received error causes from interworking MSC Unid Uniden enti tifie fiedS dSub ubsc scri ribe berr 0x5 0x5 UNID UNIDEN ENTIF TIFIE IED_ D_SU SUBS BSSC SCRI RIBE BER R 0x31 0x314 4 AbsentSubscriber AbsentSubscriber 0x1B ABSENT_SUBSCRIBER ABSENT_SUBSCRIBER 0x10 Subsc ubscri rib berB erBusy usyForM ForMTT-S SMS 0x1F B_SUB SUBSCR SCRIBE IBER_BUS _BUSY Y 0x5 Faci Facili lity tyNo NotS tSup uppo port rted ed 0x15 0x15 FACI FACILI LITY TY_N _NOT OT_S _SUP UPPO PORT RTED ED 0x81 0x810 0 IllegalSubscriber 0x9 ILLEGAL_SUBSCRIBER 0x313 Ille Illega galE lEqu quip ipme ment nt 0xC 0xC ILLE ILLEGA GAL_ L_SU SUBS BSCR CRIB IBER ER_S _STA TATI TION0x ON0x31 319 9 SystemFailure 0x22 NETWORK_FAILURE 0x811 UnexpectedDataValue 0x24 MAP_FAILURE 0x812 DataMissing 0x23 MAP_FAILURE 0x812
4.1.11 4.1.11.1 .1
Intern Internal al probl problems ems
RESTRICT_IN_OUT_DIRECTION RESTRICT_IN_OUT_ DIRECTION 0x300 SMHPRB sets this clear code in the following situations:
3000 SM is barred by the subscriber.
OPER_RESTR_IN_OUT_DIRECT OPER_RESTR_IN_OUT_DIRECT 0x301 SMHPRB sets this clear code in the following situations:
3000 SM is barred by operator.
ILLEGAL_SUBSCRIBER ILLEGAL_SUBSCRI BER 0x313 The MMCPRB sets this error cause if subscriber identification is performed after authentication and the fetched IMSI differs from the IMSI stored to the VLR.
ERR_REQ_FROM_CO_PROCESS ERR_REQ_FROM_CO_PROCESS 0x405 The MMCPRB sets this error cause if the co-process tries to send a message to the MMCPRB resource that is no longer reserved for the service.
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
26/114
ERR_ANSWER_FROM_CO_PROCESS 0x407 SMHPRB sets this clear code in the following situations:
3000 SMSC address analyse fails in GSAPRB inquiry.
MAP_CONGESTION 0x40C The MMCPRB sets this error cause if it has no resources available to handle the VLR enquiry. SMHPRB sets this clear code in the following situations:
0003 Service request has been rejected because of MO-SM VMSC hand reservation failure.
FILE_ERROR 0x509 SMHPRB sets this clear code in the following situations:
3000 Address of the VMSC is unknown. This may have been caused by a failed reading of the HRNFIL or there is no MSC address in the HRNFIL.
NO_RESPONSE_FROM_CO_PROCES 0x603 The MMCPRB sets this error cause if the time control expires for the co-process (not for VLR resource) response. SMHPRB sets this clear code in the following situations:
3000 Hand process has not received the dialogue start message from the master process. 3001 No response from GSAPRB when waiting for the GSAPRB inquiry response. 3002 No response from MMCPRB when waiting for the subscriber information inquiry response from the VLR. 3003
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
27/114
No response from MTAPRB or SMHPRB when waiting for the hand ID in forwarding of SM from the IWMSC. 3004 No response from MTAPRB or SMHPRB when waiting for the forwarding of SM response from the IWMSC.
OVERLOAD_CONGESTION 0x60B The MMCPRB sets this error cause if overload control does not give permission to continue access management data enquiry from the VLR when identification is performed before authentication.
FACILITY_NOT_SUPPORTED 0x810 The MMCPRB sets this error cause if access management data enquiry from VLR is started with incorrect service_type.
NETWORK_FAILURE 0x811 The MMCPRB sets this error cause with additional clear situation information to inform the VLR resource that the TMSI reallocation response shall be still waited for after co-process abort. SMHPRB sets this clear code in the following situations:
3000 Incorrect MAP message from the IWMSC.
NO_VLR_RESPONSE 0x81C The MMCPRB sets this error cause if time control expires for the VLR resource response.
SUBS_SIGN_INVALID_SM 0xD50 SMHPRB sets this clear code in the following situations:
3000 Illegal message type indicator in the user info from the A interface. 3001 User info length from the A interface is too short. 3002 PNP-translation fails in the PNP inquiry.
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
28/114
4.1.12
Mobile terminating short message service
4.1.13
Mobile terminating short message service in gateway MSC
SMHPRB: Mapping table for received error causes from visitor MSC DeliveryFailureOutOfMemory 0x20 MEMORY_CAPACITY_EXCEEDED0x316 0x00 DeliveryFailure other than OutOfMemory 0x20 SUBS_SIG_PROTOCOL_ERROR 0xD04 MTAPRB: Mapping table for received error causes from visitor MSC UnidentifiedSubscriber 0x5 UNIDENTIFIED_SUBSCRIBER 0x314 AbsentSubscriber 0x1B ABSENT_SUBSCRIBER 0x10 SubscriberBusyForMT-SMS 0x1F B_SUBSCRIBER_BUSY 0x5 FacilityNotSupported 0x15 FACILITY_NOT_SUPPORTED 0x810 IllegalSubscriber 0x9 ILLEGAL_SUBSCRIBER 0x313 IllegalEquipment 0xC ILLEGAL_SUBSCRIBER_STATION0x319 SystemFailure 0x22 NETWORK_FAILURE 0x811 UnexpectedDataValue 0x24 MAP_FAILURE 0x812 DataMissing 0x23 MAP_FAILURE 0x812 If the SMHPRB receives SystemFailure error cause from the visitor MSC with RadioSubsystem info in the diagnostics field, parameter SMS_SYSTEM_FAIL_USED in PRFILE is set on and the subscriber belongs to their own network, the SMHPRB translates it to ABSENT_SUBSCRIBER 0x10 ( Feature 714: Encrypted Authentication Data Transfer
4.1.13.1
Internal problems
FILE_ERROR 0x509 SMHPRB sets this clear code in the following situations:
2000 Address of the GMSC is unknown. This may have been caused by a failed reading of the HRNFIL or there is no MSC address in the HRNFIL.
NO_RESPONSE_FROM_CO_PROCESS 0x603 SMHPRB sets this clear code in the following situations:
2000 Hand process has not received the dialogue start message from the master process. 2001 No response from MTAPRB when waiting for the hand ID in the routing information inquiry from the HLR. © Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
29/114
2004 No response from MTAPRB when waiting for the routing information inquiry response from the HLR. 2005 No response from MTAPRB or SMHPRB when waiting for the hand ID in the forwarding of the SM from the VMSC. 2006 No response from MTAPRB or SMHPRB when waiting for the forwarding of the SM response from the VMSC. 2007 No response from OSHORT when waiting for the MMS message from the SMSC.
NETWORK_FAILURE 0x811 SMHPRB sets this clear code in the following situations:
2000 Incorrect MMS message from the SMSC. 2001 Incorrect MAP message from the VMSC.
SUBS_SIGN_INVALID_SM 0xD50 SMHPRB sets this clear code in the following situations:
2000 Illegal message type indicator in the user info from the SMSC. 2001 User info length from the SMSC exceeds the maximum legal length. 2002 User info length from the SMSC is too short.
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
30/114
4.1.14
Mobile terminating short message service in visitor MSC
If the SMHPRB receives NoPagingResponse error cause from the VLR, the SMHPRB translates it to ABSENT_SUBSCRIBER 0x10 ( FN714 ).
4.1.14.1
Internal problems
ERR_REQ_FROM_CO_PROCESS 0x405 The MMCPRB sets this error cause if the co-process tries to send a message to the MMCPRB resource that is no longer reserved for the service.
ERR_ANSWER_FROM_CO_PROCESS 0x407 The MMCPRB sets this error cause if it receives an IMEI enquiry response from the A interface although IMEI checking is not activated.
MAP_CONGESTION 0x40C The MMCPRB sets this error cause if it has no resources available to handle the VLR enquiry. SMHPRB sets this clear code in the following situations:
0001 Service request has rejected because of MT-SM VMSC hand reservation failure.
NO_RESPONSE_FROM_CO_PROCESS 0x603 The MMCPRB sets this error cause if time control expires for co-process (not for VLR resource) response. SMHPRB sets this clear code in the following situations:
1000 Hand process has not received the dialogue start message from the master process. 1002 No response from MMCPRB when waiting for the hand ID in subscriber information inquiry from the VLR. 1003 No response from MMCPRB when waiting for the subscriber information inquiry response from the VLR. 1004
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
31/114
No response from SHMPRB when waiting for the forwarding of SM response from the A interface. 1005 No response from SHMPRB when waiting for the forwarding of SM response in queueing from the A interface. 1006 No response from MTAPRB or SMHPRB when waiting for the MMS message from the GMSC.
OVERLOAD_CONGESTION 0x60B The MMCPRB sets this error cause if there are too too many unhandled messages in the BSU when the VLR enquiry is started. SMHPRB sets this clear code in the following situations:
1000 No response from GCGPRO when waiting for the overload checking response.
UNIT_RESTARTED 0x60E SMHPRB sets this clear code in the following situations:
1000 Address of the MMCPRB is unknown. This may have been caused by the restart of the BSU unit.
NETWORK_FAILURE 0x811 The MMCPRB sets this error cause if subscriber identification is performed after authentication and the fetched IMSI differs from the IMSI stored to the VLR. Furthermore this error cause is used with additional clear situation information to inform the VLR resource that the TMSI reallocation response shall be still waited for after co-process abort.
NO_VLR_RESPONSE 0x81C The MMCPRB sets this error cause if the time control expires for VLR resource response.
SUBS_SIGN_INVALID_SM 0xD50 SMHPRB sets this clear code in the following situations:
1000
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
32/114
Illegal message type indicator in the user info from the GMSC. 1001 User info length from the GMSC exceeds the maximum legal length. 1002 User info length from the GMSC is too short.
4.1.15
Mobile originating unstructured SS data
4.1.16
Internal problems
ILLEGAL_SUBSCRIBER 0x313 The MMCPRB sets this error cause if subscriber identification is performed after authentication and the fetched IMSI differs from the IMSI stored to the VLR.
ERR_REQ_FROM_CO_PROCESS 0x405 The MMCPRB sets this error cause if the co-process tries to send a message to the MMCPRB resource that is no longer reserved for the service.
MAP_CONGESTION 0x40C The MMCPRB sets this error cause if it has no resources available to handle the VLR enquiry.
NO_RESPONSE_FROM_CO_PROCESS 0x603 The MMCPRB sets this error cause if time control expires for co-process (not for VLR resource) response. USSDAM sets this clear code in the following situations:
2000 Hand process has not received the dialogue start message from the master process. 2001 No response from AISPRB when waiting for the USSD from the MS. 2002 No response from MTAPRB when waiting for the hand ID in forwarding the USSD from the network.
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
33/114
2003 No response from MTAPRB when waiting for the USSD acknowledgement from the network. 2004 No response from AISPRB when waiting for the subsequent USSD acknowledgement from the MS.
OVERLOAD_CONGESTION 0x60B The MMCPRB sets this error cause if overload control does not give permission to continue the access management data enquiry from the VLR when identification is performed before authentication.
FACILITY_NOT_SUPPORTED 0x810 The MMCPRB sets this error cause if the access management data enquiry from the VLR is started with an incorrect service_type.
MAP_FAILURE 0x812 USSDAM sets this clear code in the following situations:
2000 USSD response length from the HLR exceeds maximum length of the USSD value in PRFILE. 2001 Operation code from MAP is illegal in the subsequent USSD. 2002 Subsequent USSD length from HLR exceeds the maximum length of the USSD value in PRFILE. 2003 Subsequent USSD length from the HLR is too short.
SUBS_SIG_PROTOCOL_ERROR 0xD04 The Mobile Application Part MCS Program Block (MMCPRB) sets this error cause if it cannot find the VLRU pair based on roaming number. USSDAM sets this clear code in the following situations:
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
34/114
2000 Operation code from the MS is illegal in the USSD. 2001 USSD length from the MS is too short. 2002 USSD length from the MS exceeds the maximum length of the USSD value in PRFILE. 2003 USSD response length from the MS exceeds the maximum length of the USSD value in PRFILE.
4.1.17
Mobile terminating unstructured SS data
4.1.18
Internal problems
ERR_REQ_FROM_CO_PROCESS 0x405 The MMCPRB sets this error cause if the co-process tries to send a message to the MMCPRB resource that is no longer reserved for the service.
ERR_ANSWER_FROM_CO_PROCESS 0x407 The MMCPRB sets this error cause if it receives an IMEI enquiry response from the A interface although IMEI checking is not activated.
MAP_CONGESTION 0x40C The MMCPRB sets this error cause if it has no resources available to handle the VLR enquiry. USSDAM sets this clear code in the following situations:
0001 Service request has rejected because of MT-USSD hand reservation failure.
NO_RESPONSE_FROM_CO_PROCESS 0x603 The MMCPRB sets this error cause if the time control expires for the co-process (not for VLR resource) response. USSDAM sets this clear code in the following situations:
© Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
35/114
1000 Hand process has not received the dialogue start message from the master process. 1001 No response from MMCPRB when waiting for the hand ID in the subscriber information inquiry from the VLR. 1002 No response from MMCPRB when waiting for the subscriber information inquiry response from the VLR. 1003 No response from AISPRB when waiting for the USSD acknowledgement from the MS. 1004 No response from MTAPRB when waiting for the USSD acknowledgement from the network.
OVERLOAD_CONGESTION 0x60B The MMCPRB sets this error cause if there are too too many unhandled messages in the BSU when the VLR enquiry is started.
UNIT_RESTARTED 0x60E USSDAM sets this clear code in the following situations:
1000 Address of the MMCPRB is unknown. This may have been caused by the restart of the BSU unit.
NETWORK_FAILURE 0x811 The MMCPRB sets this error cause if subscriber identification is perfomermed after authentication and the fetched IMSI differs from the IMSI stored to the VLR. Furthermore this error cause is used with additional clear situation information to inform the VLR resource that the TMSI reallocation response shall be still waited for after co-process abort.
MAP_FAILURE 0x812 USSDAM sets this clear code in the following situations:
1000 © Nokia Siemens Networks
DN0124783, issue 5-0
MAP mapping
36/114
Operation code from MAP is illegal in the USSD. 1001 USSD length from the HLR is too short. 1002 USSD length from HLR exceeds the maximum length of the USSD value in PRFILE. 1003 Operation code from MAP is illegal in the subsequent USSD. 1004 Subsequent USSD length from the HLR exceeds the maximum length of the USSD value in PRFILE. 1005 Subsequent USSD length from the HLR is too short.
NO_VLR_RESPONSE 0x81C The MMCPRB sets this error cause if the time control expires for the VLR resource response.
SUBS_SIG_PROTOCOL_ERROR 0xD04 USSDAM sets this clear code in the following situations:
1000 USSD response length from the MS exceeds the maximum length of the USSD value in PRFILE.
4.1.19
Subscriber location report in VMSC
Mapping table for received error causes from GMLC SystemFailure 0x22 NETWORK_FAILURE 0x811 UnexpectedDataValue 0x24 MAP_FAILURE 0x812 DataMissing 0x23 MAP_FAILURE 0x812 ResourceLimitation 0x31 N_OVERLOAD_CONGESTION 0x81F UnknownSubscriber 0x1 B_NUMBER_UNUSED 0x307 UnauthorizedRequestingNetwork 0x34 UNAUTHORIZED_LCS_REQUEST 0x103E UnknownOrUnreachableLCSClient 0x3A UNAUTHORIZED_LCS_REQUEST 0x103E
© Nokia Siemens Networks
DN0124783, issue 5-0
RANAP mapping
37/114
5 RANAP mapping 5.1.1 Radio Access Network Application Part (RANAP) All RANAP codes are based on the following recommendations: 3GPP TS 25.413: UTRAN Iu interface Radio Access Network Application Part (RANAP) signalling
Messages MESSAGES RAB ASSIGNMENT REQUEST RAB ASSIGNMENT RESPONSE RAB RELEASE REQUEST IU RELEASE REQUEST IU RELEASE COMMAND RELOCATION REQUEST ACKNOWLEDGE RELOCATION PREPARATION FAILURE RELOCATION FAILURE RELOCATION CANCEL DIRECT TRANSFER (DTAP mappings are described in the BSSAP —part) External cause codes EXTERNAL CAUSE CODES
H/D RAB pre-empted 1/1 Trelocoverall Expiry 2/2 Trelocprep Expiry 3/3 Treloccomplete Expiry 4/4 Tqueing Expiry 5/5 Relocation Triggered 6/6 TRELOCalloc Expiry 7/7 Unable to Establish During Relocation 8/8 Unknown Target RNC 9/9 Relocation Cancelled 0A/10 Successful Relocation 0B/11 Requested Ciphering and/or Integrity Protection Algorithms not Supported 0C/12 Change of Ciphering and/or Integrity Protection is not supported 0D/13 Failure in the Radio Interface Procedure 0E/14 Release due to UTRAN Generated Reason 0F/15 User Inactivity 10/16 Time Critical Relocation 11/17 Requested Traffic Class not Available 12/18 Invalid RAB Parameters Value 13/19 Requested Maximum Bit Rate not Available 14/20 Requested Guaranteed Bit Rate not Available 15/21 Requested Transfer Delay not Achievable 16/22
© Nokia Siemens Networks
DN0124783, issue 5-0
38/114
RANAP mapping
Invalid RAB Parameters Combination Condition Violation for SDU Parameters Condition Violation for Traffic Handling Priority Condition Violation for Guaranteed Bit Rate User Plane Versions not Supported Iu UP Failure Relocation Failure in Target CN/RNC or Target System Invalid RAB ID No remaining RAB Interaction with other procedure Requested Maximum Bit Rate for DL not Available Requested Maximum Bit Rate for UL not Available Requested Guaranteed Bit Rate for DL not Available Requested Guaranteed Bit Rate for UL not Available Repeated Integrity Checking Failure Requested Report Type not supported Request superseded Release due to UE generated signalling connection release Resource Optimisation Relocation Requested Information Not Available Relocation desirable for radio reasons Relocation not supported in Target RNC or Target system Directed Retry Radio Connection With UE Lost RNC unable to establish all RFCs Deciphering Keys Not Available Dedicated Assistance data Not Available Relocation Target not allowed Location Reporting Congestion Reduce Load in Serving Cell No Radio Resources Available in Target cell GERAN Iu-mode failure Access Restricted Due to Shared Networks Incoming Relocation Not Supported Due To PUESBINE Feature Traffic Load In The Target Cell Higher Than In The Source Cell Unknown Iu Transport Association Iu Transport Connection Failed to Establish User Restriction Start Indication User Restriction End Indication Normal Release Transfer Syntax Error Semantic Error Message not compatible with receiver state Abstract Syntax Error (Reject) Abstract Syntax Error (Ignore and Notify) © Nokia Siemens Networks
17/23 18/24 19/25 1A/26 1B/27 1C/28 1D/29 1E/30 1F/31 20/32 21/33 22/34 23/35 24/36 25/37 26/38 27/39 28/40 29/41 2A/42 2B/43 2C/44 2D/45 2E/46 2F/47 30/48 31/49 32/50 33/51 34/52 35/53 36/54 37/55 38/56 39/57 41/65 42/66 51/81 52/82 53/83 61/97 62/98 63/99 64/100 65/101 DN0124783, issue 5-0
39/114
RANAP mapping
Abstract Syntax Error (Falsely Constructed Message) O&M Intervention No Resource Available Unspecified Failure Network Optimisation Other reasons
66/102 71/113 72/114 73/115 74/116
MAPPING TABLE, RANAP-cause to Internal cause MAPPING TABLE, RANAP-cause to Internal cause EXTERNAL CAUSE H/D INTERNAL CAUSE RAB pre-empted 1/1 operator_priority_access →
Trelocoverall Expiry
2/2
→
radio_if_congestion
Trelocprep Expiry
3/3
→
radio_if_fail_rev_to_old
Treloccomplete Expiry
4/4
→
radio_if_congestion
Tqueing Expiry
5/5
→
radio_if_msg_failure
Relocation Triggered
6/6
→
radio_if_congestion
TRELOCalloc Expiry
7/7
→
radio_if_congestion
Unable to Establish During Relocation
8/8
→
radio_if_congestion
Relocation Cancelled
0A/10
→
handover_failure
Successful Relocation
0B/11
→
ho_successful
Requested Ciphering and/or Integrity Protection Algorithms not Supported Change of Ciphering and/or Integrity Protection is not supported Failure in the Radio Interface Procedure
0C/12
→
ciphering_not_succeeded
0D/13
→
ciphering_not_succeeded
0E/14
→
radio_if_msg_failure
Release due to UTRAN-Generated Reason User Inactivity
0F/15
→
radio_if_fail
10/16
→
ranap_protocol_error
Time Critical Relocation
11/17
→
ho_cause_better_cell
Requested Traffic Class not Available
12/18
→
radio_if_congestion
Invalid RAB Parameters Value
13/19
→
ranap_protocol_error
© Nokia Siemens Networks
H = 0x00000011 = 0x00000205 = 0x00000B1C = 0x00000205 = 0x00000B1B = 0x00000205 = 0x00000205 = 0x00000205 = 0x00000B14 = 0x0000100B = 0x00000B15 = 0x00000B15 = 0x00000B1B = 0x00000B13 = 0x00000845 = 0x00001008 = 0x00000205 = 0x00000845
DN0124783, issue 5-0
40/114
RANAP mapping
Requested Maximum Bit Rate not 14/20 Available Requested Guaranteed Bit Rate not 15/21 Available Requested Transfer Delay not Achievable 16/22
→
→
→
Invalid RAB Parameters Combination
17/23
→
Condition Violation for SDU Parameters
18/24
→
Condition Violation for Traffic Handling Priority Condition Violation for Guaranteed Bit Rate User Plane Versions not Supported
19/25
→
1A/26
→
1B/27
→
Iu UP Failure
1C/28
→
Relocation Failure in Target CN/RNC or Target System Invalid RAB ID
1D/29
→
1E/30
→
No remaining RAB
1F/31
→
Interaction with other procedure
20/32
→
Requested Maximum Bit Rate for DL not Available Requested Maximum Bit Rate for UL not Available Requested Guaranteed Bit Rate for DL not Available Requested Guaranteed Bit Rate for UL not Available Repeated Integrity Checking Failure
21/33
→
22/34
→
23/35
→
24/36
→
25/37
→
Requested Report Type not supported
26/38
→
Request superseded
27/39
→
Release due to UE generated signalling connection release Resource Optimisation Relocation
28/40
→
29/41
→
Requested Information Not Available
2A/42
→
Relocation desirable for radio reasons
2B/43
→
© Nokia Siemens Networks
radio_if_congestion
= 0x00000205 radio_if_congestion = 0x00000205 radio_if_congestion = 0x00000205 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 radio_if_congestion = 0x00000205 req_terrestrial_res_unava = 0x00000B1F radio_if_fail_rev_to_old = 0x00000B1C ranap_protocol_error = 0x00000845 normal_unspecified = 0x00000015 radio_if_fail_rev_to_old = 0x00000B1C radio_if_congestion = 0x00000205 radio_if_congestion = 0x00000205 radio_if_congestion = 0x00000205 radio_if_congestion = 0x00000205 radionw_as_msg_failure = 0x00000844 position_method_failure = 0x0000103D radio_if_congestion = 0x00000205 remote_equipment_failure = 0x00000B16 ho_cause_better_cell = 0x00001008 operator_priority_access = 0x00000011 ho_cause_better_cell =
DN0124783, issue 5-0
41/114
RANAP mapping
Radio Connection with UE Lost
2E/46
→
RNC unable to establish all RFCst
2F/47
→
Relocation Target not allowed
32/50
→
Reduce Load in Serving Cell
34/52
→
No Radio Resources Available in Target cell Incoming Relocation Not Supported Due To PUESBINE Feature Signalling Transport Resource Failure
35/53
→
38/56
→
41/65
→
Iu Transport Connection Failed to Establish User Restriction Start Indication
42/66
→
51/81
→
User Restriction End Indication
52/82
→
Normal Release
53/83
→
Transfer Syntax Error
61/97
→
Semantic Error
62/98
→
Message not compatible with receiver state Abstract Syntax Error (Reject)
63/99
→
64/100
→
Abstract Syntax Error (Ignore and Notify) 65/101
→
Abstract Syntax Error (Falsely Constructed Message) O&M Intervention
66/102
→
71/113
→
No Resource Available
72/114
→
Network Optimisation
74/116
→
Other reasons
→
0x00001008 radio_if_fail = 0x00000B13 req_terrestrial_res_unava = 0x00000B1F radio_if_fail_rev_to_old = 0x00000B1C ho_cause_better_cell = 0x00001008 radio_resource_unavailable = 0x00000B1E facility_not_supported = 0x00000810 rnw_init_sign_con_failure = 0x00000846 req_terrestrial_res_unava = 0x00000B1F facility_not_supported = 0x00000810 facility_not_supported = 0x00000810 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 ranap_protocol_error = 0x00000845 n_o_and_m_intervention = 0x00000B1D radio_resource_unavailable = 0x00000B1E ho_cause_better_cell = 0x00001008 remote_equipment_failure = 0x00000B16
MAPPING TABLE, BSSMAP-cause to RANAP-cause The following cause codes are used in Inter System Handovers. The mappings are valid inside one MSC.
© Nokia Siemens Networks
DN0124783, issue 5-0
RANAP mapping
42/114
MAPPING TABLE, BSSMAP-cause to RANAP-cause BSSMAP CAUSE H/D RANAP CAUSE radio_if_mess_fail_c 0 / 0 Relocation Cancelled radio_if_fail_c 1/1 Relocation Cancelled uplink_quality_c 2/2 Time Critical Relocation uplink_strength_c 3/3 Time Critical Relocation downlink_quality_c 4/4 Time Critical Relocation downlink_strength_c 5 / 5 Time Critical Relocation distance_c 6/6 Time Critical Relocation o_and_m_inter_c 7/7 O&M Intervention resp_to_msc_invoc_c 8 / 8 Time Critical Relocation call_control_c 9/9 Interaction with other procedure handover_succ_c B / 11 Successful Relocation better_cell_c C/ Time Critical Relocation 12 directed_retry_c D/ Directed Retry 13 traffic_c F / 15 Time Critical Relocation tr_l_higher_t_cell_c 11 / Traffic Load In The Target Cell Higher Than In The 17 Source Cell equipment_fail_c 20 / Relocation Cancelled 32 req_terr_res_unava_c 22 / No Resource Available 34 ccch_overload_c 23 / No Resource Available 35 processor_overload_c 24 / No Resource Available 36 bss_not_equipped_c 25 / Relocation not supported in Target RNC or Target 37 system ms_not_equipped_c 26 / Relocation not supported in Target RNC or Target 38 system invalid_cell_c 27 / Unknown Target RNC 39 traffic_load_c 28 / Resource Optimisation Relocation 40 preemption_c 29 / RAB pre-empted 41 ciph_alg_not_supp_c 40 / Requested Ciphering and/or Integrity Protection 64 Algorithms not Supported reloc_n_s_due_pues_c42 / Incoming Relocation Not Supported Due To 66 PUESBINE Feature terr_chan_alr_allc_c 50 / Relocation Cancelled 80 invalid_msg_cont_c 51 / Abstract Syntax Error (Reject) 81 →
H/D 0A/10 0A/10 11/17 11/17 11/17 11/17 11/17 71/113 11/17 20/32 0B/11 11/17
→
2D/45
→ → → → → → → → → → → →
→
11/17 39/57
→
0A/10
→
72/114
→
72/114
→
72/114
→
2C/44
→
2C/44
→
9/9
→
29/41
→
1/1
→
0C/12
→
38/56
→
0A/10
→
64/100
→
© Nokia Siemens Networks
DN0124783, issue 5-0
RANAP mapping
43/114
inf_ele_or_fie_mis_c
52 / 82 incorrect_value_c 53 / 83 unknwn_msg_type_c 54 / 84 unknwn_info_elem_c 55 / 85 prot_err_b_bsc_msc_c 60 / 96 Any other value
Abstract Syntax Error (Falsely Constructed Message) 66/102
→
→
Requested Report Type not supported
26/38
→
Transfer Syntax Error
61/97
Abstract Syntax Error (Falsely Constructed Message) 66/102
→
→
Message not compatible with receiver state
63/99
→
Unspecified Failure
73/115
MAPPING TABLE, RANAP-cause to BSSMAP-cause The following cause codes are used in Inter System Handovers. The mappings are valid inside one MSC.
MAPPING TABLE, RANAP-cause to BSSMAP-cause RANAP CAUSE H/D BSSMAP CAUSE 1/1 preemption_c →
RAB pre-empted
→
Trelocoverall Expiry
2/2
Trelocprep Expiry Treloccomplete Expiry
3/3 4/4
Relocation Triggered
→
no_radio_res_avail_c
→
r_if_f_rev_to_old_c no_radio_res_avail_c
6/6
→
no_radio_res_avail_c
Unable to Establish During Relocation
8/8
→
no_radio_res_avail_c
Successful Relocation Requested Ciphering and/or Integrity Protection Algorithms not Supported Change of Ciphering and/or Integrity Protection is not supported Release due to UTRAN-Generated Reason Time Critical Relocation
0B/11 0C/12
0F/15 11/17
Requested Traffic Class not Available
0D/13
→
→
handover_succ_c ciph_alg_not_supp_c
→
ciph_alg_not_supp_c
→
→
radio_if_fail_c better_cell_c
12/18
→
no_radio_res_avail_c
Invalid RAB Parameters Value
13/19
→
invalid_msg_cont_c
Requested Maximum Bit Rate not Available
14/20
→
no_radio_res_avail_c
Requested Guaranteed Bit Rate not Available
15/21
→
no_radio_res_avail_c
Requested Transfer Delay not Achievable
16/22
→
no_radio_res_avail_c
© Nokia Siemens Networks
→
H/D 29 / 41 21 / 33 A / 10 21 / 33 21 / 33 21 / 33 B / 11 40 / 64 40 / 64 1/1 C/ 12 21 / 33 51 / 81 21 / 33 21 / 33 21 / 33
DN0124783, issue 5-0
44/114
RANAP mapping
Invalid RAB Parameters Combination
17/23
→
invalid_msg_cont_c
Condition Violation for SDU Parameters
18/24
→
invalid_msg_cont_c
Condition Violation for Traffic Handling Priority
19/25
→
invalid_msg_cont_c
Condition Violation for Guaranteed Bit Rate
1A/26
→
invalid_msg_cont_c
User Plane Versions not Supported
1B/27
→
no_radio_res_avail_c
Iu UP Failure
1C/28
→
req_terr_res_unava_c
IRelocation Failure in Target Invalid RAB ID
1D/29 1E/30
No remaining RAB Interaction with other procedure Requested Maximum Bit Rate for DL not Available
1F/31 20/32 21/33
Requested Maximum Bit Rate for UL not Available
→ →
r_if_f_rev_to_old_c invalid_msg_cont_c
→
call_control_c r_if_f_rev_to_old_c no_radio_res_avail_c
22/34
→
no_radio_res_avail_c
Requested Guaranteed Bit Rate for DL not Available
23/35
→
no_radio_res_avail_c
Requested Guaranteed Bit Rate for UL not Available
24/36
→
no_radio_res_avail_c
Repeated Integrity Checking Failure
25/37
→
invalid_msg_cont_c
Requested Report Type not supported
26/38
→
incorrect_value_c
Request superseded
27/39
→
no_radio_res_avail_c
Release due to UE generated signalling connection release Resource Optimisation Relocation
28/40
→
call_control_c
29/41
→
better_cell_c
Relocation desirable for radio reasons
2B/43
→
Directed retry
2D/45
→
Radio Connection With UE Lost RNC unable to establish all RFCs
2E/46 2F/47
Relocation Target not allowed Reduce Load in Serving Cell
32/50 34/52
No Radio Resources Available in Target cell
35/53
© Nokia Siemens Networks
→ →
→ →
→ →
→
51 / 81 51 / 81 51 / 81 51 / 81 21 / 33 22 / 34 A / 10 51 / 81 9/9 A / 10 21 / 33 21 / 33 21 / 33 21 / 33 51 / 81 53 / 83 21 / 33 9/9
C/ 12 better_cell_c C/ 12 directed_retry_c D/ 13 radio_if_fail_c 1/1 req_terr_res_unava_c 22 / 34 r_if_f_rev_to_old_c A / 10 red_load_serv_cell_c 10 / 16 tr_l_higher_t_cell_c 11 / 17 DN0124783, issue 5-0
RANAP mapping
45/114
GERAN Iu-mode failure
36/54
→
Incoming Relocation Not Supported Due To PUESBINE Feature Traffic Load In The Target Cell Higher Than In The Source Cell Signalling Transport Resource Failure
38/56
→
39/57
→
41/65
→
Iu Transport Connection Failed to Establish
42/66
→
User Restriction Start Indication User Restriction End Indication Normal Release Transfer Syntax Error
51/81 52/82 53/83 61/97
Semantic Error
62/98
→
Message not compatible with receiver state
63/99
→
Abstract Syntax Error (Reject)
64/100
→
Abstract Syntax Error (Ignore and Notify)
65/101
→
Abstract Syntax Error (Falsely Constructed Message) 66/102
→
O&M Intervention No Resource Available
71/113 72/114
Network Optimisation
74/116
Any other value
→ → → →
→ →
→
→
geran_iu_failure_c
41 / 65 reloc_n_s_due_pues_c42 / 66 tr_l_higher_t_cell_c 11 / 17 invalid_msg_cont_c 51 / 81 req_terr_res_unava_c 22 / 34 o_and_m_inter_c 7/7 o_and_m_inter_c 7/7 call_control_c 9/9 invalid_msg_cont_c 51 / 81 invalid_msg_cont_c 51 / 81 prot_err_b_bsc_msc_c 60 / 96 invalid_msg_cont_c 51 / 81 invalid_msg_cont_c 51 / 81 invalid_msg_cont_c 51 / 81 o_and_m_inter_c 7/7 req_terr_res_unava_c 22 / 34 better_cell_c C/ 12 equipment_fail_c 20 / 32
MAPPING TABLE, RANAP-cause to AAL2-cause AAL2 causes are based on the following recommendations: •
•
ITU-T Q.850: Usage of cause and location in the Digital Subscriber Signalling System No. 1 and the Signalling System No. 7 ISDN User Part ITU-T Q.2610: Usage of cause and location in B-ISDN user part and DSS2 Cause code mappings are done in R99 MGW.
MAPPING TABLE, RANAP-cause to AAL2-cause RANAP CAUSE H/D AAL2 CAUSE RAB pre-empted 1/1 Preemption Trelocoverall Expiry 2/2 Interworking, unspecified → → →
© Nokia Siemens Networks
H/D 8/8 7F / 127
DN0124783, issue 5-0
46/114
RANAP mapping
Trelocprep Expiry
3/3
→
Interworking, unspecified
Treloccomplete Expiry
4/4
→
Interworking, unspecified
Tqueing Expiry
5/5
→
Interworking, unspecified
Relocation Triggered
6/6
→
Interworking, unspecified
TRELOCalloc Expiry
7/7
→
Interworking, unspecified
Unable to Establish During Relocation
8/8
→
Unknown Target RNC
9/9
→
Resource unavailable, unspecified Interworking, unspecified
Relocation Cancelled
0A/10
→
Interworking, unspecified
Successful Relocation
0B/11
→
Interworking, unspecified
→
Interworking, unspecified
→
Interworking, unspecified
→
Interworking, unspecified
Requested Ciphering and/or Integrity Protection 0C/12 Algorithms not Supported Conflict with already existing Integrity protection 0D/13 and/or Ciphering information Failure in the Radio Interface Procedure 0E/14 Release due to UTRAN-Generated Reason
0F/15
→
Interworking, unspecified
Time Critical Relocation
11/17
→
Interworking, unspecified
Requested Traffic Class not Available
12/18
→
Invalid RAB Parameters Value
13/19
→
Requested Maximum Bit Rate not Available
14/20
→
Requested Guaranteed Bit Rate not Available
15/21
→
Requested Transfer Delay not Achievable
16/22
→
Invalid RAB Parameters Combination
17/23
→
Condition Violation for SDU Parameters
18/24
→
Condition Violation for Traffic Handling Priority
19/25
→
Condition Violation for Guaranteed Bit Rate
1A/26
→
User Plane Versions not Supported
1B/27
→
© Nokia Siemens Networks
Service or option not available, unspecified Service or option not available, unspecified Service or option not available, unspecified Service or option not available, unspecified Service or option not available, unspecified Service or option not available, unspecified Service or option not available, unspecified Service or option not available, unspecified Service or option not available, unspecified Service or option not
7F / 127 7F / 127 7F / 127 7F / 127 7F / 127 2F / 47 7F / 127 7F / 127 7F / 127 7F / 127 7F / 127 7F / 127 7F / 127 7F / 127 3F / 63 3F / 63 3F / 63 3F / 63 3F / 63 3F / 63 3F / 63 3F / 63 3F / 63 3F /
DN0124783, issue 5-0
47/114
RANAP mapping
Iu UP Failure
1C/28
→
Relocation Failure in Target CN/RNC or Target System Invalid RAB ID
1D/29
→
1E/30
→
No remaining RAB
1F/31
→
Requested Information Not Available
2A/42
→
Reduce Load in Serving Cell
34/52
→
No Radio Resources Available in Target cell
35/53
→
GERAN Iu-mode failure
36/54
→
Access Restricted Due to Shared Networks
37/55
→
Signalling Transport Resource Failure
41/65
→
Iu Transport Connection Failed to Establish
42/66
→
Normal Release
53/83
→
Transfer Syntax Error
61/97
→
Semantic Error
62/98
→
Message not compatible with receiver state
63/99
→
Abstract Syntax Error (Reject)
64/100
→
Abstract Syntax Error (Ignore and Notify)
65/101
→
Abstract Syntax Error (Falsely Constructed Message) No Resource Available
66/102
→
72/114
→
Unspecified Failure
73/115
→
Any other value
→
available, unspecified Resource unavailable, unspecified Interworking, unspecified
63 2F / 47 7F / 127 Service or option not 3F / available, unspecified 63 Normal, unspecified 1F / 31 Service or option not 3F / available, unspecified 63 Normal, unspecified 1F / 31 Normal, unspecified 1F / 31 Normal, unspecified 1F / 31 Normal, unspecified 1F / 31 Resource unavailable, 2F / unspecified 47 Resource unavailable, 2F / unspecified 47 Normal call clearing 10 / 16 Protocol error, unspecified 6F / 111 Mandatory information 60 / element is missing 96 Message not compatible with 65 / call state 101 Protocol error, unspecified 6F / 111 Protocol error, unspecified 6F / 111 Protocol error, unspecified 6F / 111 Resource unavailable, 2F / unspecified 47 Normal, unspecified 1F / 31 Normal, unspecified 1F / 31
MAPPING TABLE, AAL2-cause to RANAP-cause AAL2 causes are based on the following recommendations:
© Nokia Siemens Networks
DN0124783, issue 5-0
RANAP mapping
48/114 •
•
ITU-T Q.850: Usage of cause and location in the Digital Subscriber Signalling System No. 1 and the Signalling System No. 7 ISDN User Part ITU-T Q.2610: Usage of cause and location in B-ISDN user part and DSS2 Cause code mappings are done in R99 MGW.
MAPPING TABLE, AAL2-cause TO RANAP-cause AAL2 CAUSE H/D RANAP CAUSE Unallocated (unassigned) number 1/1 No Resource Available → →
No route to specified transit network
2/2
→
No Resource Available
No route to destination
3/3
→
No Resource Available
Channel unacceptable
6/6
→
No Resource Available
Preemption Normal call clearing
8/8 10/16
User busy
→
RAB pre-empted Normal Release
11/17
→
No Resource Available
No user responding
12/18
→
No Resource Available
No answer from user (user alerted)
13/19
→
No Resource Available
Subscriber absent
14/20
→
No Resource Available
Call rejected
15/21
→
No Resource Available
Number changed
16/22
→
No Resource Available
Number not assigned
18/24
→
No Resource Available
Non-selected user clearing
1A/26
→
No Resource Available
Destination out of order
1B/27
→
No Resource Available
Invalid number format (address incomplete)
1C/28
→
No Resource Available
Facility rejected
1D/29
→
No Resource Available
Response to STATUS ENQUIRY
1E/30
→
No Resource Available
Normal, unspecified
1F/31
→
Unspecified Failure
Too many pending add party request
20/32
→
No Resource Available
No circuit/channel available
22/34
→
No Resource Available
© Nokia Siemens Networks
→
H/D 72 / 114 72 / 114 72 / 114 72 / 114 1/1 53 / 83 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 73 / 115 72 / 114 72 /
DN0124783, issue 5-0
49/114
RANAP mapping
Requested VPCI/VCI not available
23/35
→
No Resource Available
VPCI/VCI assignment failure
24/36
→
No Resource Available
User cell rate not available
25/37
→
No Resource Available
Network out of order
26/38
→
No Resource Available
Permanent frame mode connection out of service
27/39
→
No Resource Available
Permanent frame mode connection operational
28/40
→
No Resource Available
Temporary failure
29/41
→
No Resource Available
Switching equipment congestion
2A/42
→
No Resource Available
Access information discarded
2B/43
→
No Resource Available
Requested circuit/channel not available
2C/44
→
No Resource Available
No VPCI/VCI available
2D/45
→
No Resource Available
Precedence call blocked
2E/46
→
No Resource Available
Resource unavailable, unspecified
2F/47
→
No Resource Available
Quality of service not available
31/49
→
No Resource Available
Requested facility not subscribed
32/50
→
No Resource Available
Outgoing calls barred within CUG
35/53
→
No Resource Available
Incoming calls barred within CUG
37/55
→
No Resource Available
Bearer capability not authorized
39/57
→
No Resource Available
Bearer capability not available presently
3A/58
→
No Resource Available
Call restriction
3B/59
→
No Resource Available
Terminal transfer rejected
3C/60
→
No Resource Available
Inconsistency in designated outgoing access information and subscriber class Service or option not available, unspecified
3E/62
→
No Resource Available
3F/63
→
No Resource Available
© Nokia Siemens Networks
114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 72 / 114
DN0124783, issue 5-0
50/114
RANAP mapping
Bearer capability not implemented
41/65
→
No Resource Available
Channel type not implemented
42/66
→
No Resource Available
Requested facility not implemented
45/69
→
No Resource Available
→
No Resource Available
→
No Resource Available
Only restricted digital information bearer capability 46/70 is available Service or option not implemented, unspecified 4F/79 Invalid call reference value
51/81
→
Semantic Error
Identified channel does not exist
52/82
→
Semantic Error
A suspended call exists, but this call identity does not Call identity in use
53/83
→
Semantic Error
54/84
→
Semantic Error
No call suspended
55/85
→
Semantic Error
Call having the requested call identity has been cleared User not member of CUG
56/86
→
Semantic Error
57/87
→
Semantic Error
Incompatible destination
58/88
→
Semantic Error
Non-existent CUG
5A/90
→
Semantic Error
Invalid transit network selection
5B/91
→
Semantic Error
Bad CS parameter
5C/92
→
Semantic Error
AAL parameters cannot be supported
5D/93
→
Semantic Error
Invalid message, unspecified
5F/95
→
Semantic Error
Mandatory information element is missing
60/96
→
Semantic Error
Message type non-existent or not implemented
61/97
→
Semantic Error
Message not compatible with call state or message 62/98 type non-existent or not implemented Information element/parameter non-existent or not 63/99 implemented Invalid information element contents 64/100 Message not compatible with call state © Nokia Siemens Networks
65/101
→
Message not compatible with receiver state Semantic Error
→
Semantic Error
→
Message not compatible
→
72 / 114 72 / 114 72 / 114 72 / 114 72 / 114 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 62 / 98 63 / 99 62 / 98 62 / 98 63 /
DN0124783, issue 5-0
51/114
RANAP mapping
Recovery on timer expiry
66/102
Parameter non-existent or not implemented, 67/103 passed on Message with unrecognised parameter, discarded 6E/110
→
with receiver state Semantic Error
→
Semantic Error
→
Semantic Error
Protocol error, unspecified
6F/111
→
Transfer Syntax Error
Support service not available
71/113
→
No Resource Available
Information item end-to-end transfer not possible
72/114
→
No Resource Available
Switch to conversation position
7E/126
→
No Resource Available
Interworking, unspecified
7F/127
→
No Resource Available
→
Unspecified failure
Undefined codes (not according to specifications)
© Nokia Siemens Networks
99 62 / 98 62 / 98 62 / 98 61 / 97 72 / 114 72 / 114 72 / 114 72 / 114 73 / 115
DN0124783, issue 5-0
SIP mapping
52/114
6 SIP mapping 6.1.1 Signalling SIP signalling(general)
SIP message number CANCEL BYE 380 400 401 402 403 404 405 406 407 408 409 410 411 413 414 415 420 421 423 480 481 482 483 484 485 486 488 490 491 493 500 501
SIP to clear code mapping SIP message name hex INTERNAL CLEAR CODE 15H normal_unspecified 0H normal_end_of_the_call 0H normal_end_of_the_call A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed 817H n_unallocated_number A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed 819H n_subscriber_nbr_changed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed D07H no_user_responding A03H interworking_failed
→ →
Alternative Service Bad Request Unauthorized Payment Requeired Forbidden Not Found Method Not Allowed Not Acceptable Proxy Authentication Required Request Timeout Conflict Gone Length Required Request Entity Too Large Request URI Too Large Unsupported Media Type Bad Extension Extension Required Interval Too Brief Temporarily not available Cal Leg/Transaction Does Not Exist Loop Detected Too Many Hops Address Incomplete Ambiguous Busy Here Not Acceptable Here Request Updated Request Pending Undecipherable Internal Server Error Not Implemented
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → →
→ →
A03H interworking_failed A03H interworking_failed B17H adress_incomplete A03H interworking_failed 005H b_subscriber_busy A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed
→ → → → → →
→ →
DN0124783, issue 5-0
SIP mapping
53/114
502 503 504 505 513 580 600 603 604 606 3xx 4xx 5xx 6xx
hex 001H 004H 005H 006H 007H 008H 009H 012H 00AH 00BH 00CH 010H 013H 015H 016H 020H 025H 100H 101H 102H 103H 201H 204H 206H
Bad Gateway Service Unavailable Server Time-out SIP Version not supported Message Too Large Precondition-Failure Busy Everywhere Decline Does not exist anywhere Not Acceptable any SIP3xx which is not listed above any SIP4xx which is not listed above any SIP5xx which is not listed above any SIP6xx which is not listed above
A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed A03H interworking_failed 005H b_subscriber_busy 206H call_rejected 817H n_unallocated_number A03H interworking_failed A03H interworking_failed
→ → → → → → → → → → →
A03H interworking_failed
→
A03H interworking_failed
→
→
005H b_subscriber_busy
Clear Code to SIP mapping INTERNAL CLEAR CODE SIP MESSAGE NUMBER SIP MESSAGE NAME suspended_call 480 Temporarily unavailable b_subscri_busy_or_congest 486 Busy here b_subscriber_busy 486 Busy here b_answer_time_out 480 Temporarily unavailable call_waiting_time_out 480 Temporarily unavailable b_not_connected 404 Not found call_already_waiting 486 Busy here no_paging_response 480 Temporarily unavailable intervention_already_on 480 Temporarily unavailable rerout_due_to_b_facility 480 Temporarily unavailable cris_mode_out_restriction 503 Service unavailable absent_subscriber 480 Temporarily unavailable ct_recall_time_out 480 Temporarily unavailable normal_unspecified 480 Temporarily unavailable cha_capa_of_subs_exceeded 480 Temporarily unavailable intercept_ann_ok 480 Temporarily unavailable cdb_release 480 Temporarily unavailable circuit_re_seized 480 Temporarily unavailable crct_released_during_call 480 Temporarily unavailable call_record_rel_dur_calibr 480 Temporarily unavailable charg_in_wrong_call_phase 480 Temporarily unavailable call_released 503 Service unavailable established_channel 480 Temporarily unavailable call_rejected 480 Temporarily unavailable
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → → → → →
DN0124783, issue 5-0
SIP mapping
54/114
207H 20BH 20EH 210H 211H 213H 215H 217H 218H 219H 220H 252H 270H 300H 301H 304H 305H 306H 307H 308H 309H 30CH 30DH 30EH 30FH 310H 311H 312H 315H 317H 31AH 31CH 31DH 321H 322H 323H 400H 401H 402H 403H 404H 405H 406H 407H 408H
subscriber_congestion cl_in_toll_ticketing_case a_line_vacant null_nup n_rejected_diverted_call n_user_not_in_cug dropped_call tmp_out_of_service out_of_cat_area trans_out_of_service anonymous_call_reject misrouted_ported_call congestion_on_mgw restrict_in_out_direction oper_restr_in_out_direct b_line_out_of_service b_line_faulty b_calls_restricted b_number_unused b_number_changed intervention_time_exceeded b_onhook_time_out b_c_numb_is_not_registered b_line_blocked change_in_number_planning cug_reject bearer_serv_not_prov tele_serv_not_prov call_diversion_barring in_service_time_exceeded cug_rec_icb cug_rej_not_member cug_rej_ocb cug_rej_no_cug_selected cug_rej_unknown_cug_ind multicall_usage_rejected attenuator_congestion interw_unit_congestion regist_total_time_exceeded mfcu_congestion pbru_congestion err_req_from_co_process connect_failed_in_gsw_swi err_answer_from_co_process b_number_overflow
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
503 480 480 480 480 503 480 502 480 480 480 480 480 503 480 503 502 503 404 410 480 408 480 502 480 503 503 503 503 480 503 503 503 503 503 503 503 503 480 503 503 503 503 503 484
Service unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Service unavailable Temporarily unavailable Bad Gateway Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Service unavailable Temporarily unavailable Service unavailable Bad Gateway Service unavailable Not found Gone Temporarily unavailable Request timeout Temporarily unavailable Bad Gateway Temporarily unavailable Service unavailable Service unavailable Service unavailable Service unavailable Temporarily unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Temporarily unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Address incomplete DN0124783, issue 5-0
SIP mapping
55/114
409H 40AH 450H 451H 506H 508H 509H 50BH 50CH 50DH 50FH 600H 601H 602H 603H 604H 606H 607H 608H 609H 60BH 60DH 60EH 60FH 700H 701H 702H 704H 705H 706H 707H 70AH 70CH 70DH 70EH 710H 711H 712H 715H 716H 718H 719H 720H 721H 801H
connect_failed_in_ssw_swi traffic_type_congestion no_incoming_updr no_outgoing_updr line_hunt_group_lines_barr charging_error file_error module_rou_ssw_congestion mfc_ass_chan_close_missed facility_writing_failed unsuitable_module_circuit file_record_congestion module_link_congestion register_congestion no_response_from_co_proces intern_call_link_congestio conferen_device_congestion polarity_reversal_failure charging_not_started call_cleared_by_mml overload_congestion stage_circuit_congestion unit_restarted module_failure_call_clear long_aon_request register_analysis_failed queueing_time_exceeded parity_err_from_pbru_mfcu module_not_available call_interrupt_in_reg_ana subscriber_module_restart forced_clear_of_a_call overload_control_syst_err announcement_error configuration_error no_ana_for_oper_identifier tran_ex_not_accpt_trf org_or_iw_ex_not_accpt_trf facility_not_avail_on_outr bearer_cap_not_fullfilled cm_analysis_congestion no_resource_for_call res_not_avail_in_cmn user_plane_ana_problem original_b_number_overflow
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
503 480 503 503 503 503 503 503 503 503 503 503 502 503 503 503 503 480 503 480 503 503 503 503 480 480 503 503 502 480 503 480 480 503 503 404 503 503 503 503 503 503 480 503 480
Service unavailable Temporarily unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Bad Gateway Service unavailable Service unavailable Service unavailable Service unavailable Temporarily unavailable Service unavailable Temporarily unavailable Service unavailable Service unavailable Service unavailable Service unavailable Temporarily unavailable Temporarily unavailable Service unavailable Service unavailable Bad Gateway Temporarily unavailable Service unavailable Temporarily unavailable Temporarily unavailable Service unavailable Service unavailable Not found Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Temporarily unavailable Service unavailable Temporarily unavailable DN0124783, issue 5-0
SIP mapping
56/114
802H 803H 804H 806H 807H 808H 809H 80AH 80BH 80CH 80DH 80EH 80FH 810H 811H 813H 814H 815H 817H 818H 819H 81AH 81DH 81EH 81FH 820H 821H 822H 824H 826H 827H 828H 829H 830H 851H 860H 861H 870H 871H 872H 873H 874H 875H 900H 901H
a_number_overflow invalid_subscri_a_category outgoing_circ_congestion a_identity_not_available r2_signal_pause_time_out r2_sign_backwards_time_out r2_err_signl_from_out_crct r2_err_signal_from_in_crct no_b_numb_to_send_out_crct unknown_incoming_dec_sign out_circuit_out_of_order in_circuit_out_of_order circuit_congestion facility_not_supported network_failure switching_equ_congestion circuit_group_congestion b_access_barred n_unallocated_number n_line_out_of_service n_subscriber_nbr_changed terminal_congestion international_congestion controlled_not_ready n_overload_congestion n_msg_content_error invalid_transit_n_select n_recovery_timer_expiry pcm_faulty unrec_param_msg_discarded cic_not_allowed_in_crct n_national_congestion call_congestion_by_dcme n_ported_number scc_congestion apm_reassembly_error apm_unid_addr_error h248_protocol_error servicechange_received unknown_user_plane_dest error_in_codec_negotiation undefined_interconnection bnc_estab_notific_err no_mf_forward_signal too_long_mf_forward_signal
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
480 480 480 480 480 480 480 480 480 480 503 503 503 503 503 503 480 503 404 502 410 503 480 503 503 503 404 480 480 503 480 480 480 480 503 502 502 480 480 480 606 480 480 480 480
Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Service unavailable Temporarily unavailable Service unavailable Not found Bad Gateway Gone Service unavailable Temporarily unavailable Service unavailable Service unavailable Service unavailable Not found Temporarily unavailable Temporarily unavailable Service unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Service unavailable Bad Gateway Bad Gateway Temporarily unavailable Temporarily unavailable Temporarily unavailable Not Acceptable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable DN0124783, issue 5-0
SIP mapping
57/114
905H 90CH 90DH 90EH 90FH A01H A02H A03H A04H A05H A07H A08H A09H A0AH A0CH A0DH B0FH B17H B18H B19H B20H B21H B23H B2AH B2BH B2CH B2DH B2EH B2FH B30H B31H B33H B34H B35H B36H B37H B38H B39H B3AH B3BH B3CH B3DH C00H C01H C02H
too_long_mf_backw_signal premat_seizu_ack_out_crct seizu_ack_time_out_in_crct premature_answer answer_after_b_busy idle_control_end_missed trunk_circ_invalid_msg interworking_failed trunk_circ_protocol_error crct_released_by_co_exc call_failure_from_out_crct destinat_sign_out_of_order address_complete_time_out address_comp_send_time_out digital_path_not_provided no_route_to_destination changed_b_number_overflow adress_incomplete service_unavailable service_incompatible nae_error dte_uncontrolled dual_seizure_both_way_crct blocking_received param_no_exist_or_impl in_protocol_error in_appl_response_time_out in_trig_cnt_limit_reached in_tcap_error asn1_codec_error call_gapped cont_check_fail in_a_nbr_not_subscriber in_cc_nbr_block_for_fraud in_cc_nbr_not_found in_disconnect_for_fraud in_fallback_code_one in_fallback_code_two in_fallback_code_three in_fallback_code_five in_fallback_code_four in_ss7_routing_failure dial_wait_time_exceeded prohibited_dialling insufficient_dialling
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
480 480 480 480 500 480 503 480 503 480 480 503 484 484 503 503 480 484 503 503 480 480 480 480 503 480 480 480 480 480 503 480 503 484 484 480 480 480 480 480 480 480 484 484 484
Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Server internal error Temporarily unavailable Service unavailable Temporarily unavailable Service unavailable Temporarily unavailable Temporarily unavailable Service unavailable Address incomplete Address incomplete Service unavailable Service unavailable Temporarily unavailable Address incomplete Service unavailable Service unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Service unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Service unavailable Temporarily unavailable Service unavailable Address incomplete Address incomplete Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Address incomplete Address incomplete Address incomplete DN0124783, issue 5-0
58/114
C04H a_has_dial_wrong_keyword C05H a_has_no_right_mod_facil C06H a_has_no_right_store_numb C08H premature_dialling C09H serv_facil_activa_restrict C0AH serv_facil_usage_restrict C0BH inconsist_between_a_and_b D00H subs_signa_msg_content_err D01H subs_signa_msg_format_err D03H serv_facil_not_implemented D04H subs_sig_protocol_error D06H aocc_charging_error D07H no_user_responding D08H gsm_erh408_prot_timer_exp D0BH double_login D0FH facility_rejected D10H mandatory_ie_missing D11H invalid_ie_content 100AH repeat_attempt 100DH cf_uncon_notif_to_a 101DH b_busy_through_connect 101FH b_modem_subs_busy 1020H b_modem_subs_unobtainable
SIP mapping → → → → → → → → → → → → → → → → → → → → → → →
484 503 503 480 503 503 503 503 480 503 503 480 480 480 480 480 480 480 480 480 486 486 480
Address incomplete Service unavailable Service unavailable Temporarily unavailable Service unavailable Service unavailable Service unavailable Service unavailable Temporarily unavailable Service unavailable Service unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Temporarily unavailable Busy here Busy here Temporarily unavailable
The other Clear Codes (which are not in the above table) are mapped to 500 Server Internal Error SIP message.
© Nokia Siemens Networks
DN0124783, issue 5-0
59/114
MEGACO mapping
7 MEGACO mapping 7.1.1 Signalling The signalling is based on ITU-T H.248.1 : Gateway control protocol: Version 2
7.1.2 Cause code mapping The following received H248 error codes from media gateway are mapped to internal cause codes.
Mapping table for received error codes from MGW EXTERNAL H248 CAUSE EVENT DEC MAPPING INTERNAL CAUSE CODES HEX CODES / ERROR CODES / DIRECTION SERVICE CHANGE REASON CODES “NR” Normal Release 001 normal_end_of_the_call 0x000 “UR” Unavailable Resources 002 congestion_on_mgw 0x843 “FT” Failure, Temporay 003 mgw_internal_failure 0x885 “FP” Failure, Permanent 004 mgw_internal_failure 0x885 “IW” Interworking Error 005 interworking_failed 0xa03 “UN” Unsupported 006 unused_h248_error_code 0x88b Syntax error in message 400 h248_protocol_error 0x870 Protocol Error 401 h248_protocol_error 0x870 Unauthorized 402 mgw_problem_with_req_serv 0x887 Syntax Error in TransactionRequest 403 h248_protocol_error 0x870 Version Not Supported 406 h248_protocol_error 0x870 Incorrect identifier 410 h248_protocol_error 0x870 The transaction refers to an unknown 411 context_info_mismatch 0x884 ContextID No ContextIDs available 412 congestion_on_mgw 0x843 Unknown action or illegal combination 421 unused_h248_error_code 0x88b of actions Syntax Error in Action 422 h248_protocol_error 0x870 Unknown TerminationID 430 termination_info_mismatch 0x88a No TerminationID matched a wildcard 431 termination_info_mismatch 0x88a Out of TerminationIDs or No 432 congestion_on_mgw 0x843 TerminationID available TerminationID is already in a Context 433 mgw_term_double_seizure 0x888 Max number of Terminations in a 434 congestion_on_mgw 0x843 Context exceeded Termination ID is not in specified 435 context_info_mismatch 0x884 Context Unsupported or unknown Package 440 mgw_not_supp_h248_item 0x886 Missing Remote or Local Descriptor 441 h248_protocol_error 0x870 → → → → → → → → → → → → →
→ →
→ → → →
→ →
→
→ →
© Nokia Siemens Networks
DN0124783, issue 5-0
60/114
MEGACO mapping
Syntax Error in Command Unsupported or Unknown Command Unsupported or Unknown Descriptor Unsupported or Unknown Property Unsupported or Unknown Parameter Descriptor not legal in this command Descriptor appears twice in a command Unsupported or Unknown Parameter or Property Value No such property in this package No such event in this package No such signal in this package No such statistic in this package No such parameter value in this package Property illegal in this Descriptor Property appears twice in this Descriptor Missing parameter in signal or event Unexpected Event/Request ID Internal software failure in the MG Not Implemented Not ready
442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 500 501 502
Service Unavailable 503 Command Received from 504 unauthorized entity Transaction Request Received before 505 a ServiceChange Reply has been received Number of Transaction Pendings 506 Exceeded Insufficient resources 510 Media Gateway unequipped to detect 512 requested Event Media Gateway unequipped to 513 generate requested Signals Media Gateway cannot send the 514 specified announcement Unsupported Media Type 515 Unsupported or invalid mode 517 Event buffer full 518 Out of space to store digit map 519 Digit Map undefined in the MG 520 Termination is "Service Changing" 521 © Nokia Siemens Networks
→
h248_protocol_error mgw_not_supp_h248_item mgw_not_supp_h248_item mgw_not_supp_h248_item mgw_not_supp_h248_item h248_protocol_error h248_protocol_error
0x870 0x886 0x886 0x886 0x886 0x870 0x870
→
mgw_not_supp_h248_item
0x886
h248_protocol_error h248_protocol_error h248_protocol_error h248_protocol_error h248_protocol_error
0x870 0x870 0x870 0x870 0x870
h248_protocol_error h248_protocol_error
0x870 0x870
h248_protocol_error h248_protocol_error mgw_internal_failure mgw_not_supp_h248_item mgw_problem_with_req _serv unused_h248_error_code unused_h248_error_code
0x870 0x870 0x885 0x886 0x887 0x88b 0x88b
→
h248_protocol_error
0x870
→
unused_h248_error_code
0x88b
→ → → → → →
→ → → → →
→ →
→ → → → →
→ →
→
congestion_on_mgw 0x843 mgw_problem_with_req_serv 0x887
→
mgw_problem_with_req_serv 0x887
→
mgw_problem_with_req_serv 0x887
→
→ → → → → →
mgw_not_supp_h248_item mgw_not_supp_h248_item congestion_on_mgw congestion_on_mgw mgw_not_supp_h248_item unused_h248_error_code
0x886 0x886 0x843 0x843 0x886 0x88b
DN0124783, issue 5-0
61/114
Insufficient bandwidth Internal hardware failure in MG Temporary Network failure Permanent Network failure Audited Property, Statistic, Event or Signal does not exist Response exceeds maximum transport PDU size Illegal write or read only property Unexpected initial hook state Does Not Exist Illegal syntax within an announcement specification Variable type not supported Variable value out of range Category not supported Selector type not supported Selector value not supported Unknown segment ID Mismatch between play specification and provisioned data Provisioning error Invalid offset No free segment IDs Temporary segment not found Segment in use ISP port limit overrun No modems available Calling number unacceptable Called number unacceptable Premature termination of operation Invalid command key sequence detected Max attempts exceeded No digits No speech was collected after prompts Out of storage Unable to delete temporary audio segment Service Restored Cold Boot Warm Boot MGC Directed Change Termination malfunctioning
© Nokia Siemens Networks
MEGACO mapping 526 529 530 531 532 533 534 540 581 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 622 623 624 900 901 902 903 904
→
congestion_on_mgw mgw_internal_failure network_failure network_failure termination_info_mismatch
0x843 0x885 0x811 0x811 0x88a
→
congestion_on_mgw
0x843
h248_protocol_error termination_info_mismatch unused_h248_error_code h248_protocol_erro
0x870 0x88a 0x88b 0x870
→ → → →
→ → → →
→ → → → → → →
→ → → → → → → → → → →
→ → →
→ →
→ → → → →
mgw_not_supp_h248_item 0x886 mgw_problem_with_req_serv 0x887 mgw_not_supp_h248_item 0x886 mgw_not_supp_h248_item 0x886 mgw_not_supp_h248_item 0x886 mgw_not_supp_h248_item 0x886 mgw_problem_with_req_serv 0x887 mgw_problem_with_req_serv 0x887 mgw_problem_with_req_serv 0x887 congestion_on_mgw 0x843 mgw_problem_with_req_serv 0x887 mgw_problem_with_req_serv 0x887 mgw_problem_with_req_serv 0x887 congestion_on_mgw 0x843 mgw_problem_with_req_serv 0x887 mgw_problem_with_req_serv 0x887 mgw_problem_with_req_serv 0x887 mgw_problem_with_req_serv 0x887 congestion_on_mgw 0x843 congestion_on_mgw 0x843 mgw_problem_with_req_serv 0x887 congestion_on_mgw 0x843 mgw_problem_with_req_serv 0x887 servicechange_received servicechange_received servicechange_received servicechange_received term_taken_out_of_service
0x871 0x871 0x871 0x871 0x889
DN0124783, issue 5-0
62/114
Termination taken out of service Loss of lower layer connectivity Transmission Failure MG Impending Failure MGC Impending Failure Media Capability Failure Modem Capability Failure Mux Capability Failure Signal Capability Failure Event Capability Failure State Loss Packages change Capabilities change
© Nokia Siemens Networks
MEGACO mapping 905 906 907 908 909 910 911 912 913 914 915 916 917
→ → → → → → → → → → → → →
term_taken_out_of_service term_taken_out_of_service term_taken_out_of_service term_taken_out_of_service servicechange_received servicechange_received capability_failure_in_mgw capability_failure_in_mgw capability_failure_in_mgw capability_failure_in_mgw servicechange_received unused_h248_error_code unused_h248_error_code
0x889 0x889 0x889 0x889 0x871 0x871 0x883 0x883 0x883 0x883 0x871 0x88b 0x88b
DN0124783, issue 5-0
BICC mapping
63/114
8 BICC mapping 8.1.1 Signalling Bearer Independent Call Control (BICC)
8.1.2 Cause code mapping MESSAGES MESSAGE IDENTIFIER RELEASE 0C CONFUSION 2F RELEASE COMPLETE 10 ADDRESS COMPLETE 06 CALL PROGRESS 2C EXTERNAL CAUSE CODES unallocated number no route to spec. trans. netw. no route to destination send special information tone misdialled trunk prefix preemption preempt. circuit res. for reuse QoR: ported number normal call clearing user busy no user responding no answer from user subscriber absent call rejected number changed routing error destination out of order address incomplete facility rejected normal, unspecified no circuit available network out of order temporary failure switching equipment congestion access information discarded requested channel not available precedence call blocked resource unavailable, unspecif. © Nokia Siemens Networks
NUMBER (Hex/Dec) 0x01/01 0x02/02 0x03/03 0x04/04 0x05/05 0x08/08 0x09/09 0x0E/14 0x10/16 0x11/17 0x12/18 0x13/19 0x14/20 0x15/21 0x16/22 0x19/25 0x1B/27 0x1C/28 0x1D/29 0x1F/31 0x22/34 0x26/38 0x29/41 0x2A/42 0x2B/43 0x2C/44 0x2E/46 0x2F/47 DN0124783, issue 5-0
BICC mapping
64/114
requested facil. not subscribed 0x32/50 outgo. calls barred within CUG 0x35/53 incom. calls barred within CUG 0x37/55 bearer capability not authoriz. 0x39/57 bear. cap. not presently avail. 0x3A/58 inconsit. in outg. access inf. 0x3E/62 serv/opt. not available, unsp. 0x3F/63 bearer capabil. not implemented 0x41/65 requested facility not implemt. 0x45/69 only res. dig. inf. b.c. avail. 0x46/70 serv/opt. not implemented, unsp. 0x4F/79 called user not member of CUG 0x57/87 incompatible destination 0x58/88 non-existent CUG 0x5A/90 invalid transit netw. selection 0x5B/91 invalid message, unspecified 0x5F/95 mess. type non-ex. or not impl. 0x61/97 parm. non-ex./not impl., disc. 0x63/99 recovery on timer expiry 0x66/102 parm. non-ex./not impl., passed 0x67/103 mess. with unrec. param., disc. 0x6E/110 protocol error, unspecified 0x6F/111 interworking, unspecified 0x7F/127
hex 0x0000 0x0005 0x0006 0x0010 0x0012 0x0013 0x0021 0x0022 0x0027 0x0106 0x0201 0x0202 0x0205 0x0206 0x0207 0x0212 0x0213 0x0300 0x0304
Mapping of internal clear code to external cause code INTERNAL CLEAR CODE hex/ dec EXTERNAL CAUSE CODE normal_end_of_the_call 0x10/16 normal call clearing b_subscriber_busy 0x11/17 user busy b_answer_time_out 0x13/19 no answer from user absent_subscriber 0x14/20 absent subscriber no_paging_response 0x12/18 no user responding ct_recall_time_out 0x13/19 no answer from user b_busy_ccbs_possible 0x11/17 user busy, diagnostics : ccbs possible. b_busy_ccbs_not_possible 0x11/17 user busy, diagnostics : ccbs not possible. hunt_serv_rel 0x10/16 normal call clearing bor_configuration_failure 0x15/21 call_rejected call_released 0x15/21 call rejected clear_request_rec_out_crct 0x10/16 normal call clearing radio_if_congestion 0x22/34 no circuit available call_rejected 0x15/21 call rejected subscriber_congestion 0x2F/47 resource unavail., unsp. n_unknown_dialling 0x1C/28 address incomplete n_user_not_in_cug 0x57/87 cal. user not mem. of CUG restrict_in_out_direction 0x58/88 incompatible destination b_line_out_of_service 0x1B/27 destination out of order
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → →
DN0124783, issue 5-0
65/114
0x0305 b_line_faulty 0x0306 call_rejected_c 0x0307 b_number_unused 0x0308 b_number_changed 0x030A cl_a_onhook_set_up_phase 0x030B cl_a_onhook_answer_phase 0x030C b_onhook_time_out 0x030E b_line_blocked 0x0310 cug_reject 0x0311 bearer_serv_not_prov 0x0312 tele_serv_not_prov 0x0313 illegal_subscriber 0x0314 unidentified_subscriber 0x0315 call_diversion_barring 0x0316 memory_capacity_exceeded 0x0317 in_service_time_exceeded 0x0319 illegal_subscriber_station 0x031A cug_rej_icb 0x031C cug_rej_not_member 0x031D cug_rej_ocb 0x031F cug_rej_bs_violation 0X0320 cug_rej_ss_violation 0x0401 interw_unit_congestion 0x0402 regist_total_time_exceeded 0x0403 mfcu_congestion 0x0404 pbru_congestion 0x0405 err_req_from_co_process 0x0406 connect_failed_in_gsw_swi 0x0407 err_answer_from_co_process 0x0408 b_number_overflow 0x040A traffic_type_congestion 0x040B hop_ctr_exhaust 0x040C map_congestion 0x040D unallocated_roaming_number 0x040E roaming_not_allowed 0x0508 charging_error 0x0509 file_error 0x050C mfc_ass_chan_close_missed 0x0600 file_record_congestion 0x0603 no_response_from_co_proces 0x0606 conferen_device_congestion 0x0608 charging_not_started 0x0609 call cleared by MML 0x060B overload_congestion 0x060C no_free_call_record_found © Nokia Siemens Networks
BICC mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x12/18 no user responding 0x15/21 call rejected 0x01/01 unallocated number 0x16/22 number changed 0x10/16 normal call clearing 0x10/16 normal call clearing 0x66/102 recovery on timer expiry 0x12/18 no user responding 0x37/55 in. calls bar. within CUG 0x39/57 bearer cap. not author. 0x3F/63 serv/opt. not av., unsp. 0x01/01 unallocated number 0x01/01 unallocated number 0x15/21 call rejected 0x2F/47 resource unavail., unsp. 0x66/102 recovery on timer expiry 0x58/88 incompatible destination 0x37/55 in. calls bar. within CUG 0x57/87 cal. user not mem. of CUG 0x35/53 ou. calls bar. within CUG 0x1D/29 facility rejected 0x1D/29 facility rejected 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x19/25 routing error 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x2F/47 resource unavail., unsp. 0x2A/42 switching equipm. cong. 0x2A/42 switching equipm. cong. DN0124783, issue 5-0
66/114
0x060E unit_restarted 0x0610 ec_failure 0x0701 register_analysis_failed 0x0706 call_interrupt_in_reg_ana 0x070A forced_clear_of_a_call 0x070B modem_error 0x070D announcement_error 0x070E configuration_error 0x070F diu_pool_error 0x0710 no_ana_for_oper_identifier 0x0713 no_isup_route 0x0715 facility_not_avail_on_outr 0x0716 bearer_cap_not_fullfilled 0x0719 no_resource_for_call 0x0804 outgoing_circ_congestion 0x0807 r2_signal_pause_time_out 0x0808 r2_sign_backwards_time_out 0x0809 r2_err_signl_from_out_crct 0x080A r2_err_signal_from_in_crct 0x080D out_circuit_out_of_order 0x080E in_circuit_out_of_order 0x080F circuit_congestion 0x0810 facility_not_supported 0x0811 network_failure 0x0812 map_failure 0x0813 switching_equ_congestion 0x0814 circuit_group_congestion 0x0815 b_access_barred 0x0816 congestion_send_info_tone 0x0817 n_unallocated_number 0x0818 n_line_out_of_service 0x0819 n_subscriber_nbr_changed 0x081A terminal_congestion 0x081B no_hlr_response 0x081C no_vlr_response 0x081F n_overload_congestion 0x0820 n_msg_content_error 0x0821 invalid_transit_n_select 0x0822 n_recovery_timer_expiry 0x0823 err_co_exc_call_attempt 0x0824 pcm_faulty 0x0826 unrec_param_msg_discarded 0x0827 cic_not_allowed_in_circuit 0x0832 routing_error 0x0851 scc_congestion © Nokia Siemens Networks
BICC mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x02/02 no route to spec. trans. netw. 0x22/34 no circuit available 0x1D/29 facility rejected 0x41/65 bearer cap. not implem. 0x2A/42 switching equipm. cong. 0x22/34 no circuit available 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x29/41 temporary failure 0x29/41 temporary failure 0x2F/47 resource unavailable, uns. 0x45/69 requested facility not imp. 0x29/41 temporary failure 0x29/41 temporary failure 0x2A/42 switching equipm. cong. 0x22/34 no circuit available 0x58/88 incompatible destination 0x04/04 send special inf. tone 0x01/01 unallocated number 0x1B/27 destination out of order 0x16/22 number changed 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2A/42 switching equipm. cong. 0x5F/95 invalid message, unsp. 0x5B/91 invalid transit netw. sel. 0x66/102 recovery on timer expiry 0x2C/44 requested channel not av. 0x2F/47 resource unavail., unsp. 0x6E/110 mess. with unr. p., disc. 0x63/99 par. non-ex./not impl., disc. 0x19/25 routing error 0x2A/42 switching equipm. cong. DN0124783, issue 5-0
67/114
0x0860 apm_reassembly_error 0x0861 apm_unid_addr_error 0x0871 servicechange_received 0x0873 error_in_codec_negotiation 0x0877 mgw_load_reduction 0x0881 unexpect_action_ind 0x0900 no_mf_forward_signal 0x090D seizu_ack_time_out_in_crct 0x0A02 trunk_circ_invalid_msg 0x0A03 interworking_failed 0x0A04 trunk_circ_protocol_error 0x0A05 crct_released_by_co_exc 0x0A08 destinat_sign_out_of_order 0x0A09 address_complete_time_out 0x0A0B inquiry_time_out 0x0A0C Digital_path_not_provided 0x0A0D no_route_to_destination 0x0B10 v110_frame_sync_fail 0x0B11 modem_communication_error 0x0B12 rlp_or_ms_frame_sync_error 0x0B14 handover_failure 0x0B15 ciphering_not_succeeded 0x0B16 remote_equipment_failure 0x0B17 address_incomplete 0x0B18 service_unavailable 0x0B19 service_incompatible 0x0B1A bssmap_protocol_error 0x0B1B radio_if_msg_failure 0x0B1C radio_if_fail_rev_to_old 0x0B1E radio_resource_unavailable 0x0B1F req_terr_resource_unavail 0x0B20 nae_error 0x0B21 dte_uncontrolled 0x0B23 dual_seizure_both_way_crct 0x0B2A blocking_received 0x0B2B param_no_exist_or_impl 0x0B2C in_protocol_error 0x0B2D in_appl_response_time_out 0x0B2F in_tcap_error 0x0B30 asn1_codec_error 0x0B31 call_gapped 0x0B33 cont_check_fail 0x0C00 dial_wait_time_exceeded 0x0C01 prohibited_dialling 0x0C02 insufficient_dialling © Nokia Siemens Networks
BICC mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x6F/111 protocol error, unsp. 0x4F/79 sserv/opt. not implemented, unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2A/42 switching equipm. cong. 0x6F/111 protocol error, unsp. 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x61/97 mess. t. non-ex/not impl. 0x7F/127 interworking, unspecif. 0x6F/111 protocol error, unsp. 0x26/38 network out of order 0x1B/27 destination out of order 0x01/01 unallocated number 0x1F/31 normal, unspecified 0x41/65 bearer cap. not implem. 0x03/03 no route to destination 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x1C/28 address incomplete 0x3F/63 serv/opt. not av., unsp. 0x58/88 incompatible destination 0x6F/111 protocol error, unsp. 0x6F/111 protocol error, unsp. 0x29/41 temporary failure 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x01/01 unallocated number 0x3F/63 serv/opt. not av., unsp. 0x2C/44 requested channel not av. 0x29/41 temporary failure 0x63/99 par. non-ex/not im., disc. 0x6F/111 protocol error, unsp. 0x66/102 recovery on timer expiry 0x6F/111 protocol error, unsp. 0x6F/111 protocol error, unsp. 0x2A/42 switching equipm. cong. 0x29/41 temporary failure 0x1C/28 address incomplete 0x01/01 unallocated number 0x1C/28 address incomplete DN0124783, issue 5-0
68/114
0x0C09 serv_facil_activa_restrict 0x0C0A serv_facil_usage_restrict 0x0C0B inconsist_between_a_and_b 0x0C0D bc_not_presently_available 0x0D00 subs_signa_msg_content_err 0x0D01 subs_signa_msg_format_err 0x0D03 serv_facil_not_implemented 0x0D04 subs_sig_protocol_error 0x0D06 aocc_charging_error 0x0D07 no_user_responding 0x0D08 gsm_erh408_prot_timer_exp 0x0D0D msg_not_cmptbl_or_impl 0x0D0E undefined_fax_data_rate 0x0D0F facility_rejected Other internal causes
BICC mapping → → → → → → → → → → → → → → →
0x39/57 bearer cap. not authoriz. 0x3F/63 serv/opt. not av., unsp. 0x58/88 incompatible destination 0x3A/58 bear. cap. not pr. avail. 0x6F/111 protocol error, unsp. 0x6F/111 protocol error, unsp. 0x41/65 bearer cap. not implem. 0x6F/111 protocol error, unsp. 0x29/41 temporary failure 0x12/18 no user responding 0x66/102 recovery on timer expiry 0x61/97 mess. t. non-ex/not impl. 0x4F/79 serv/opt. not impl., unsp. 0x1D/29 facility rejected 0x1F/31 normal, unspecified
Mapping of external cause code to internal clear code hex/ dec EXTERNAL CAUSE CODE hex INTERNAL CLEAR CODE 0x01/01 unallocated number 0x0817 un_allocated_number 0x02/02 no route to spec. tra. net. 0x0710 no_ana_for_oper_identifier 0x03/03 no route to destination 0x0A0D no_route_to_destination 0x04/04 send special inform. tone 0x0816 congestion_send_info_tone 0x05/05 misdialled trunk prefix 0x0817 n_unallocated_number 0x08/08 preemption 0x0015 normal_unspecified 0x09/09 preem. cir. res. for reuse 0x0015 normal_unspecified 0x0E/14 QoR: ported number 0x0830 n_ported_number 0x10/16 normal call clearing 0x0000 normal_end_of_the_call 0x11/17 user busy 0x0005 b_subscriber_busy 0x12/18 no user responding 0x0D07 no_user_responding 0x13/19 no answer from user 0x0006 b_answer_time_out 0x14/20 subscriber absent 0x0010 absent_subscriber_c 0x15/21 call rejected 0x0206 call_rejected 0x16/22 number changed 0x0819 n_subscriber_nbr_changed 0x19/25 routing error 0x0832 routing_error 0x1B/27 destination out of order 0x0818 n_line_out_of_service 0x1C/28 address incomplete 0x0B17 address_incomplete 0x1D/29 facility rejected 0x0D0F facility rejected 0x1F/31 normal, unspecified 0x0015 normal_unspecified 0x22/34 no circuit available 0x0814 circuit_group_congestion 0x26/38 network out of order 0x0A05 crct_released_by_co_exc 0x29/41 temporary failure 0x0811 network_failure 0x2A/42 switching equipment conges. 0x0813 switching_equ_congestion 0x2B/43 access information discard. 0x0015 normal_unspecified 0x2C/44 requested channel not ava. 0x080F circuit_congestion 0x2E/46 precedence call blocked 0x0811 network_failure → → → → → → → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
BICC mapping
69/114
0x2F/47 resource unavailable, uns. 0x32/50 requested facil. not subsc. 0x35/53 outg. calls bar. within CUG 0x37/55 inc. calls bar. within CUG 0x39/57 bearer capab. not authoriz. 0x3A/58 bear. cap. not pres. avail. 0x3E/62 incon. in outg. access inf. 0x3F/63 serv/opt. not avail., unsp. 0x41/65 bearer capabil. not implem. 0x45/69 requested facility not imp. 0x46/70 only res. dig. inf. b.c. a. 0x4F/79 serv/opt. not impl., unsp. 0x57/87 called user not mem. of CUG 0x58/88 incompatible destination 0x5A/90 non-existent CUG 0x5B/91 invalid transit netw. sel. 0x5F/95 invalid message, unspecif. 0x61/97 mess. t. non-ex. or not im. 0x63/99 parm. non-ex./not im., di. 0x66/102 recovery on timer expiry 0x67/103 parm. non-ex./not im., pa. 0x6E/110 mess. with unr. p., disc. 0x6F/111 protocol error, unspecif. 0x7F/127 interworking, unspecified other external causes
→ → → → → → → → → → → → → → → → → → → → → → → → →
0x080F circuit_congestion 0x0C09 serv_facil_usage_restrict 0x031D cug_rej_ocb 0x0310 cug_reject 0x0C09 serv_facil_activa_restrict 0x0C0D bc_not_presently_available 0x0320 cug_rej_ss_violation 0x0C0A serv_facil_usage_restrict 0x0D03 serv_facil_not_implemented 0x0810 facility_not_supported 0x0A0C Digital_path_not_provided 0x0D03 serv_facil_not_implemented 0x0213 n_user_not_in_cug 0x0C0B inconsist_between_a_and_b 0x0213 n_user_not_in_cug 0x0821 invalid_transit_n_select 0x0820 n_msg_content_error 0x0A02 trunk_circ_invalid_msg 0x0B2B param_no_exist_or_impl 0x0822 n_recovery_timer_expiry 0x0B2B param_no_exist_or_impl 0x0826 unrec_param_msg_discarded 0x0A04 trunk_circ_protocol_error 0x0A03 interworking_failed 0x0015 normal_unspecified
Mapping differences in special cases 0x10/16 in REL before ACM is sent 0x030A cl_a_onhook_set_up_phase 0x10/16 in REL before ANM is sent 0x030B cl_a_onhook_answer_phase 0x11/17 diagnostics : ccbs possib. 0x0021 b_busy_ccbs_possible 0x11/17 diagnostics : ccbs not poss. 0x0022 b_busy_ccbs_not_possible → → → →
Internal clear codes generated by BICC INTERNAL FAILURE DESCRIPTIONS hex INTERNAL CLEAR CODE waiting for COT, timer T8 expires 0x0811 network_failure RSC or GRS msg received 0x0A05 crct_released_by_co_exc wrong message in state 0x0A04 trunk_circ_protocol_error clear call request from CIC 0x0A05 forced_clear_of_a_call clear call request from MML 0x0609 call_cleared_by_mml clear call request from RFR 0x070A forced_clear_of_a_call signalling link is down (and does not recover within 1 0x0A08 destinat_sign_out_of_order min) no response from co-processwithin protection timer 0x0603 no_response_from_co_proces blocking received after 0x0B2A blocking_received erroneous value received from CC when packing 0x0405 err_req_from_co_process → → → → → → →
→ → →
© Nokia Siemens Networks
DN0124783, issue 5-0
70/114
BICC mapping
outgoing message erroneous address received in IAM message call attempt to out or blocked circuit from coexchange In coming call is released because of overload control Unsupported transmission medium requirement received in IAM dual seizure, control in co-exchange ICC rejects the call ICC does not response to call setup RMA timeout call is cleared because of compability information of unknown parameter received from co-exchange call is cleared because of compability information of unknown message received from co-exchange traffic is reduced due to signalling link congestion SI7 has no resources to handle the call Information request timer T33 expires UCIC received
→
0x0212 n_unknown_dialling 0x0823 err_co_exc_call_attempt
→
0x060B overload_congestion
→
0x0D03 serv_facil_not_implemented
→
→
0x0B23 dual_seizure_both_way_crct 0x060B overload_congestion 0x0603 no_response_from_co_proces 0x0603 no_response_from_co_proces 0x0B2B param_no_exist_or_impl
→
0x0A02 trunk_circ_invalid_msg
→ → → →
→ → → →
0x0851 scc_congestion 0x0719 no_resource_for_call 0x0A0B inquiry_time_out 0x0825 n_unknown_circuit
8.1.3 Calling party category mapping MESSAGES MESSAGE IDENTIFIER INITIAL ADDRESS01 EXTERNAL CATEGORY VALUES NUMBER (Hex/Dec) unknown 0x00/00 operator, language French 0x01/01 operator, language English 0x02/02 operator, language German 0x03/03 operator, language Russian 0x04/04 operator, language Spanish 0x05/05 ordinary calling subscriber 0x0A/10 calling subscrib. with priority 0x0B/11 data call 0x0C/12 test call 0x0D/13 payphone 0x0F/15 Mapping of the internal category to external category hex/ dec INTERNAL (CC) CATEGORY hex/ dec EXTERNAL CATEGORY 0x00/00 ordinary_1_c 0x0A/10 ordinary calling subscr. 0x04/04 data_line_c 0x0C/12 data call 0x05/05 pay_phone_c 0x0F/15 payphone 0x08/08 priority_1_c 0x0B/11 calling subs. with prior. → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
BICC mapping
71/114
0x10/16 test_equipment_c 0x27/39 oper_fre_c 0x28/40 oper_eng_c 0x29/41 oper_ger_c 0x2A/42 oper_rus_c 0x2B/43 oper_spa_c 0xFF/255 unknown_c Other internal categories
→ → → → → → → →
0x0D/13 test call 0x01/01 operator, lang. French 0x02/02 operator, lang. English 0x03/03 operator, lang. German 0x04/04 operator, lang. Russian 0x05/05 operator, lang. Spanish 0x00/00 unknown 0x0A/10 ordinary calling subscr.
Mappings used between Nokia MSSs hex/ dec INTERNAL (CC) CATEGORY hex/ dec EXTERNAL CATEGORY 0x41/65 cc_pbx_c 0xE5/229 pbx 0x42/66 cc_pnp_c 0xF3/243 pnp 0x43/67 cc_pcn_c 0xF4/244 pcn → → → →
Mapping of external category to internal category, Phase 1 (SS Mapping) hex/dec EXTERNAL CATEGORY hex/dec INTERNAL (CC) CATEGORY 0x00/00 unknown 0xFF/255 unknown_c 0x01/01 operator, lang. French 0x27/39 oper_fre_c 0x02/02 operator, lang. English 0x28/40 oper_eng_c 0x03/03 operator, lang. German 0x29/41 oper_ger_c 0x04/04 operator, lang. Russian 0x2A/42 oper_rus_c 0x05/05 operator, lang. Spanish 0x2B/43 oper_spa_c 0x0A/10 ordinary calling subscr. 0x00/00 ordinary_1_c 0x0B/11 calling sub. with prior. 0x08/08 priority_1_c 0x0C/12 data call 0x04/04 data_line_c 0x0D/13 test call 0x10/16 test_equipment_c 0x0F/15 payphone 0x05/05 pay_phone_c Other external categories 0x00/00 ordinary_1_c → → → → → → → → → → → → →
Mapping used between MSSs, Phase 1 (SS Mapping) hex/ dec EXTERNAL CATEGORY hex/ dec INTERNAL (CC) CATEGORY 0xE5/229 pbx 0x41/65 cc_pbx_c 0xF3/243 pnp 0x42/66 cc_pnp_c 0xF4/244 pcn 0x43/67 cc_pcn_c → → → →
Mapping of external category to internal category, Phase 2 (CC Mapping) hex/ dec INTERNAL (CC) CATEGORY INTERNAL (MML) CATEGORY 0x00/00 ordinary_1_c ordinary subscriber 0x04/04 data_line_c data call 0x05/05 pay_phone_c pay phone 0x08/08 priority_1_c subscriber with priority 0x10/16 test_equipment_c test phone 0x27/39 oper_fre_c operator call 0x28/40 oper_eng_c operator call 0x29/41 oper_ger_c operator call → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
72/114
0x2A/42 oper_rus_c 0x2B/43 oper_spa_c 0xFF/255 unknown_c Other external categories
© Nokia Siemens Networks
BICC mapping → → → →
operator call operator call unknown category ordinary subscriber
DN0124783, issue 5-0
73/114
ISUP mapping
9 ISUP mapping 9.1.1 Signalling ISDN User Part (ISUP)
9.1.2 Cause code mapping MESSAGES MESSAGE IDENTIFIER RELEASE 0C CONFUSION 2F not used in VMS interface RELEASE COMPLETE 10 ADDRESS COMPLETE 06 CALL PROGRESS 2C EXTERNAL CAUSE CODES NUMBER (Hex/Dec) unallocated number 0x01/01 no route to spec. trans. netw. 0x02/02 no route to destination 0x03/03 send special information tone 0x04/04 misdialled trunk prefix 0x05/05 normal call clearing 0x10/16 user busy 0x11/17 no user responding 0x12/18 no answer from user 0x13/19 call rejected 0x15/21 number changed 0x16/22 routing error 0x19/25 destination out of order 0x1B/27 address incomplete 0x1C/28 facility rejected 0x1D/29 normal, unspecified 0x1F/31 no circuit available 0x22/34 network out of order 0x26/38 temporary failure 0x29/41 switching equipment congestion 0x2A/42 requested channel not available 0x2C/44 resource unavailable, unspecif. 0x2F/47 requested facil. not subscribed 0x32/50 incom. calls barred within CUG 0x37/55 bearer capability not authoriz. 0x39/57 bear. cap. not presently avail. 0x3A/58 bearer capabil. not implemented 0x41/65 requested facility not implemt. 0x45/69 © Nokia Siemens Networks
DN0124783, issue 5-0
74/114
ISUP mapping
only res. dig. inf. b.c. avail. 0x46/70 serv/opt. not implemented, unsp. 0x4F/79 called user not member of CUG 0x57/87 incompatible destination 0x58/88 invalid transit netw. selection 0x5B/91 invalid message, unspecified 0x5F/95 mess. type non-ex. or not impl. 0x61/97 parm. non-ex./not impl., disc. 0x63/99 recovery on timer expiry 0x66/102 parm. non-ex./not impl., passed 0x67/103 protocol error, unspecified 0x6F/111 interworking, unspecified 0x7F/127 Mapping of internal clear code to external cause code hex INTERNAL CLEAR CODE hex/ dec EXTERNAL CAUSE CODE 0x0000 normal_end_of_the_call 0x10/16 normal call clearing 0x0005 b_subscriber_busy 0x11/17 user busy 0x0006 b_answer_time_out 0x13/19 no answer from user 0x0010 absent_subscriber 0x12/18 no user responding 0x0012 no_paging_response 0x12/18 no user responding 0x0013 ct_recall_time_out 0x13/19 no answer from user 0x0027 hunt_serv_rel 0x10/16 normal call clearing 0x0106 bor_configuration_failure 0x15/21 call rejected 0x0201 call_released 0x15/21 call rejected 0x0202 clear_request_rec_out_crct 0x10/16 normal call clearing 0x0205 radio_if_congestion 0x22/34 no circuit available 0x0206 call_rejected 0x15/21 call rejected 0x0207 subscriber_congestion 0x2F/47 resource unavail., unsp. 0x0212 n_unknown_dialling 0x1C/28 address incomplete 0x0213 n_user_not_in_cug 0x57/87 cal. user not mem. of CUG 0x0300 restrict_in_out_direction 0x58/88 incompatible destination 0x0304 b_line_out_of_service 0x1B/27 destination out of order 0x0305 b_line_faulty 0x12/18 no user responding 0x0306 call_rejected 0x15/21 call rejected 0x0307 b_number_unused 0x01/01 unallocated number 0x0308 b_number_changed 0x16/22 number changed 0x030A cl_a_onhook_set_up_phase 0x10/16 normal call clearing 0x030B cl_a_onhook_answer_phase 0x10/16 normal call clearing 0x030C b_onhook_time_out 0x66/102 recovery on timer expiry 0x030E b_line_blocked 0x12/18 no user responding 0x0310 cug_reject 0x37/55 in. calls bar. within CUG 0x0311 bearer_serv_not_prov 0x39/57 bearer cap. not author. 0x0312 tele_serv_not_prov 0x3F/63 serv/opt. not av., unsp. 0x0313 illegal_subscriber 0x01/01 unallocated number 0x0314 unidentified_subscriber 0x01/01 unallocated number → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
75/114
0x0315 call_diversion_barring 0x0316 memory_capacity_exceeded 0x0317 in_service_time_exceeded 0x0319 illegal_subscriber_station 0x031A cug_rej_icb 0x031C cug_rej_not_member 0x031D cug_rej_ocb 0x031F cug_rej_bs_violation 0X0320 cug_rej_ss_violation 0x0401 interw_unit_congestion 0x0402 regist_total_time_exceeded 0x0403 mfcu_congestion 0x0404 pbru_congestion 0x0405 err_req_from_co_process 0x0406 connect_failed_in_gsw_swi 0x0407 err_answer_from_co_process 0x0408 b_number_overflow 0x040A traffic_type_congestion 0x040B hop_ctr_exhaust 0x040C map_congestion 0x040D unallocated_roaming_number 0x040E roaming_not_allowed 0x0508 charging_error 0x0509 file_error 0x050C mfc_ass_chan_close_missed 0x0600 file_record_congestion 0x0603 no_response_from_co_proces 0x0606 conferen_device_congestion 0x0609 call cleared by MML 0x0608 charging_not_started 0x060B overload_congestion 0x060C no_free_call_record_found 0x060E unit_restarted 0x0610 ec_failure 0x0701 register_analysis_failed 0x0706 call_interrupt_in_reg_ana 0x070A forced_clear_of_a_call 0x070B modem_error 0x070D announcement_error 0x070E configuration_error 0x070F diu_pool_error 0x0710 no_ana_for_oper_identifier 0x0713 no_isup_route 0x0715 facility_not_avail_on_outr 0x0716 bearer_cap_not_fullfilled © Nokia Siemens Networks
ISUP mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x15/21 call rejected 0x2F/47 resource unavail., unsp. 0x66/102 recovery on timer expiry 0x58/88 incompatible destination 0x37/55 in. calls bar. within CUG 0x57/87 cal. user not mem. of CUG 0x35/53 ou. calls bar. within CUG 0x1D/29 facility rejected 0x1D/29 facility rejected 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x19/25 routing error 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x2F/47 resource unavail., unsp. 0x29/41 temporary failure 0x2A/42 switching equipm. cong. 0x2A/42 switching equipm. cong. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x02/02 no route to spec. trans. netw. 0x22/34 no circuit available 0x1D/29 facility rejected 0x41/65 bearer cap. not implem. DN0124783, issue 5-0
76/114
0x0719 no_resource_for_call 0x0804 outgoing_circ_congestion 0x0807 r2_signal_pause_time_out 0x0808 r2_sign_backwards_time_out 0x0809 r2_err_signl_from_out_crct 0x080A r2_err_signal_from_in_crct 0x080D out_circuit_out_of_order 0x080E in_circuit_out_of_order 0x080F circuit_congestion 0x0810 facility_not_supported 0x0811 network_failure 0x0812 map_failure 0x0813 switching_equ_congestion 0x0814 circuit_group_congestion 0x0815 b_access_barred 0x0816 congestion_send_info_tone 0x0817 n_unallocated_number 0x0818 n_line_out_of_service 0x0819 n_subscriber_nbr_changed 0x081A terminal_congestion 0x081B no_hlr_response 0x081C no_vlr_response 0x081F n_overload_congestion 0x0820 n_msg_content_error 0x0821 invalid_transit_n_select 0x0822 n_recovery_timer_expiry 0x0823 err_co_exc_call_attempt 0x0824 pcm_faulty 0x0827 cic_not_allowed_in_circuit 0x0832 routing_error 0x0851 scc_congestion 0x0877 mgw_load_reduction 0x0900 no_mf_forward_signal 0x090D seizu_ack_time_out_in_crct 0x0A02 trunk_circ_invalid_msg 0x0A03 interworking_failed 0x0A04 trunk_circ_protocol_error 0x0A05 crct_released_by_co_exc 0x0A08 destinat_sign_out_of_order 0x0A09 address_complete_time_out 0x0A0B inquiry_time_out 0x0A0C Digital_path_not_provided 0x0A0D no_route_to_destination 0x0B10 v110_frame_sync_fail 0x0B11 modem_communication_error © Nokia Siemens Networks
ISUP mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x2A/42 switching equipm. cong. 0x22/34 no circuit available 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x29/41 temporary failure 0x29/41 temporary failure 0x2F/47 resource unavail., unsp. 0x45/69 requested facility not imple. 0x29/41 temporary failure 0x29/41 temporary failure 0x2A/42 switching equipm. cong. 0x22/34 no circuit available 0x58/88 incompatible destination 0x04/04 send special inf. tone 0x01/01 unallocated number 0x1B/27 destination out of order 0x16/22 number changed 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x2A/42 switching equipm. cong. 0x5F/95 invalid message, unsp. 0x5B/91 invalid transit netw. selection. 0x66/102 recovery on timer expiry 0x2C/44 requested channel not av. 0x2F/47 resource unavail., unsp. 0x63/99 par. non-ex./not impl.,disc. 0x19/25 routing error 0x2A/42 switching equipm. cong. 0x2A/42 switching equipm. cong. 0x7F/127 interworking, unspecif. 0x7F/127 interworking, unspecif. 0x5F/95 invalid message, unsp. 0x7F/127 interworking, unspecif. 0x6F/111 protocol error, unsp. 0x26/38 network out of order 0x1B/27 destination out of order 0x01/01 unallocated number 0x1F/31 normal, unspecified 0x41/65 bearer cap. not implem. 0x03/03 no route to destination 0x29/41 temporary failure 0x29/41 temporary failure DN0124783, issue 5-0
77/114
0x0B12 rlp_or_ms_frame_sync_error 0x0B14 handover_failure 0x0B15 ciphering_not_succeeded 0x0B16 remote_equipment_failure 0x0B17 address_incomplete 0x0B18 service_unavailable 0x0B19 service_incompatible 0x0B1A bssmap_protocol_error 0x0B1B radio_if_msg_failure 0x0B1C radio_if_fail_rev_to_old 0x0B1E radio_resource_unavailable 0x0B1F req_terr_resource_unavail 0x0B20 nae_error 0x0B21 dte_uncontrolled 0x0B23 dual_seizure_both_way_crct 0x0B2A blocking_received 0x0B2B param_no_exist_or_impl 0x0B2C in_protocol_error 0x0B2D in_appl_response_time_out 0x0B2F in_tcap_error 0x0B30 asn1_codec_error 0x0B31 call_gapped 0x0B33 cont_check_fail 0x0C00 dial_wait_time_exceeded 0x0C01 prohibited_dialling 0x0C02 insufficient_dialling 0x0C09 serv_facil_activa_restrict 0x0C0A serv_facil_usage_restrict 0x0C0B inconsist_between_a_and_b 0x0C0D bc_not_presently_available 0x0D00 subs_signa_msg_content_err 0x0D01 subs_signa_msg_format_err 0x0D03 serv_facil_not_implemented 0x0D04 subs_sig_protocol_error 0x0D06 aocc_charging_error 0x0D07 no_user_responding 0x0D08 gsm_erh408_prot_timer_exp 0x0D0D msg_not_cmptbl_or_impl 0x0D0E undefined_fax_data_rate 0x0D0F facility rejected Other internal causes
ISUP mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x29/41 temporary failure 0x1C/28 address incomplete 0x3F/63 serv/opt. not av., unsp. 0x58/88 incompatible destination 0x6F/111 protocol error, unsp. 0x6F/111 protocol error, unsp. 0x29/41 temporary failure 0x2F/47 resource unavail., unsp. 0x2F/47 resource unavail., unsp. 0x01/01 unallocated number 0x3F/63 serv/opt. not av., unsp. 0x2C/44 requested channel not av. 0x29/41 temporary failure 0x5F/95 invalid message, unsp. 0x6F/111 protocol error, unsp. 0x66/102 recovery on timer expiry 0x6F/111 protocol error, unsp. 0x6F/111 protocol error, unsp. 0x2A/42 switching equipm. cong. 0x29/41 temporary failure 0x1C/28 address incomplete 0x01/01 unallocated number 0x1C/28 address incomplete 0x39/57 bearer cap. not authoriz. 0x3F/63 serv/opt. not av., unsp. 0x58/88 incompatible destination 0x3A/58 bear. cap. not pr. avail. 0x6F/111 protocol error, unsp. 0x6F/111 protocol error, unsp. 0x41/65 bear. cap. not implem. 0x6F/111 protocol error, unsp. 0x29/41 temporary failure 0x12/18 no user responding 0x66/102 recovery on timer expiry 0x61/97 mess. t. non-ex/not impl. 0x4F/79 serv/opt. not impl., unsp. 0x1D/29 facility rejected 0x1F/31 normal, unspecified
Mapping of external cause code to internal clear code hex/ dec EXTERNAL CAUSE CODE hex INTERNAL CLEAR CODE 0x01/01 unallocated number 0x0817 un_allocated_number → →
© Nokia Siemens Networks
DN0124783, issue 5-0
ISUP mapping
78/114
0x02/02 0x02/02 0x03/03 0x03/03 0x04/04 0x04/04 0x05/05 0x05/05 0x08/08 0x08/08 0x09/09 0x09/09 0x10/16 0x10/16 0x10/16 0x10/16 0x10/16 0x10/16 0x11/ 0x11/17 17 0x12/18 0x12/18 0x13/19 0x13/19 0x14/20 0x14/20 0x15/21 0x15/21 0x16/22 0x16/22 0x19/25 0x19/25 0x1B/27 0x1B/27 0x1C/28 0x1D/29 0x1D/29 0x1F/31 0x1F/31 0x22/34 0x22/34 0x26/38 0x26/38 0x29/41 0x29/41 0x2A/42 0x2B/43 0x2C/44 0x2E/46 0x2E/46 0x2F/47 0x2F/47 0x32/50 0x32/50 0x35/53 0x35/53 0x37/55 0x37/55 0x39/57 0x39/57 0x3A/58 0x3A/58 0x3E/62 0x3E/62 0x3F/63 0x3F/63 0x41/65 0x41/65 0x45/69 0x45/69 0x46/70 0x46/70 0x4F/79 0x4F/79 0x57/87 0x57/87 0x58/88 0x58/88 0x5A/90 0x5A/90 0x5B/91 0x5B/91 0x5F/95 0x5F/95 0x61/97 0x61/97
no route route to spec. spec. trans. trans. netw. netw. no route route to destin destination ation send special special inform inform.. tone misdiall misdialled ed trunk trunk prefix prefix preempti preemption on preem. preem. cir. cir. res. res. for reuse reuse normal normal call call clea clearing ring normal normal call call clea clearing ring normal normal call call clea clearing ring user user busy busy no user respondi responding ng no answer answer from user subscribe subscriberr absent absent call rejected rejected number number changed changed routing routing error error destinatio destination n out of order order address incomplete incomplete facility facility rejecte rejected d normal, normal, unspe unspecifie cified d no circui circuitt availa available ble network network out out of of order order temporary temporary failure failure switching equipment conges. access information discard. requested channel not ava. ava. precedenc precedence e call blocke blocked d resource resource unavail unavailable able,, uns. requested requested facil. facil. not subsc. subsc. outg. calls calls bar. withi within n CUG inc. calls calls bar. withi within n CUG bearer bearer capab. capab. not not authoriz authoriz.. bear. bear. cap. not pres. pres. avail. avail. incon. incon. in outg. outg. access access inf. serv/opt. serv/opt. not not avail., avail., unsp. unsp. bearer bearer capabi capabil. l. not not implem. implem. requested requested facility facility not not imp. imp. only res. dig. dig. inf. inf. b.c. b.c. a. serv/opt. serv/opt. not not impl., impl., unsp. unsp. called called user user not mem. mem. of of CUG incompati incompatible ble desti destinati nation on non-exis non-existent tent CUG CUG invalid invalid transit transit netw. netw. selection selection invalid invalid message message,, unspecif. unspecif. mess. mess. t. non-ex non-ex.. or not not im. im.
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x0710 no_ana_for-oper_identifie no_ana_for-oper_identifier r 0x0A0D no_route_to_destination no_route_to_destination 0x0816 congestion_send_info_to congestion_send_info_tone ne 0x0817 n_unallocated_number n_unallocated_number 0x0015 normal_unspecified normal_unspecified 0x0015 normal_unspecified normal_unspecified 0x030A clear_a_onhook_setup_p clear_a_onhook_setup_phase hase 0x030B clear_a_onhook_answe clear_a_onhook_answer_phase r_phase 0x0000 normal_end_of_the_call normal_end_of_the_call 0x0005 b_subscriber_busy b_subscriber_busy 0x0D07 no_user_responding no_user_responding 0x0006 b_answer_time_out b_answer_time_out 0x0010 absent_subscriber_c absent_subscriber_c 0x0206 call_rejected 0x0819 n_subscriber_nbr_chang n_subscriber_nbr_changed ed 0x0832 routing_error 0x0818 n_line_out_of_service n_line_out_of_service 0x0B17 address_incomplete 0x0D0F facility rejected 0x0015 normal_unspecified normal_unspecified 0x0814 circuit_group_congestion circuit_group_congestion 0x0A05 crct_released_by_co_exc 0x0811 network_failure network_failure 0x0813 switching_equ_congestio switching_equ_congestion n 0x0015 normal_unspecified normal_unspecified 0x080F circuit_congestion 0x0811 network_failure network_failure 0x080F circuit_congestion 0x0C09 serv_facil_usage_restrict serv_facil_usage_restrict 0x031D cug_rej_ocb 0x0310 cug_reject 0x0C09 serv_facil_activa_restrict serv_facil_activa_restrict 0x0C0D bc_not_presently_availab bc_not_presently_available le 0x0320 cug_rej_ss_violation cug_rej_ss_violation 0x0C0A serv_facil_usage_restrict serv_facil_usage_restrict 0x0D03 serv_facil_not_implemented serv_facil_not_implemented 0x0810 facility_not_supported facility_not_supported 0x0A0C Digital_path_not_provide Digital_path_not_provided d 0x0D03 serv_facil_not_implemented serv_facil_not_implemented 0x0213 n_user_not_in_cug n_user_not_in_cug 0x0C0B inconsist_between_a_an inconsist_between_a_and_b d_b 0x0213 n_user_not_in_cug n_user_not_in_cug 0x0821 invalid_transit_n_select invalid_transit_n_select 0x0820 n_msg_content_error n_msg_content_error 0x0A02 trunk_circ_invalid_msg DN0124783, issue 5-0
79/114
0x63/99 0x63/99 par. non-ex non-ex./not ./not impl., impl., disc. disc. 0x66/102 recovery on timer expiry 0x67/103 parm. non-ex./not im., pa. 0x6E/110 0x6E/110 mess. mess. with unr. p., disc. disc. 0x6F/111 protocol error, error, unspecif. unspecif. 0x7F/127 interworking, interworking, unspecified unspecified
ISUP mapping → → → → → →
0x0B2B param_no_exist_or_impl param_no_exist_or_impl 0x0822 n_recovery_timer_expiry n_recovery_timer_expiry 0x0B2B param_no_exist_or_impl param_no_exist_or_impl 0x0826 unrec_param_msg_disca unrec_param_msg_discarded rded 0x0A04 trunk_circ_protocol_error 0x0A03 interworking_failed
Internal cause codes generated by ISDN user part INTERNAL FAILURE DESCRIPTIONS hex INTERNAL CAUSE continuity check failed 0x0B33 cont_check_fail waiting for COT (Contin. Check), timer T8 expires 0x0811 network_failure RSC or GRS msg received 0x0A05 crct_released_by_co_exc crct_released_by_co_exc wrong message in state 0x0A04 trunk_circ_protocol_error trunk_circ_protocol_error clear call request from circuit supervision process 0x0A05 forced_clear_of_a_call forced_clear_of_a_call clear call request from MML 0x0609 call_cleared_by_mml clear call request from IWMANA (ECU restart or 0x0610 ec_failure state change) clear call request from RFR 0x070A forced_clear_of_a_call forced_clear_of_a_call signalling link is down (and does not recover within 1 0x0A08 destinat_sign_out_of_order destinat_sign_out_of_order min) no response from co-process within protection timer 0x0603 no_response_from_co_proces no_response_from_co_proces blocking received after IAM sent 0x0B2A blocking_received blocking_received erroneous value received from CC when packing 0x0405 err_req_from_co_process outgoing message erroneous address received in IAM message 0x0212 n_unknown_dialling n_unknown_dialling call attempt to out or blocked circuit from co0x0823 err_co_exc_call_attempt exchange In coming call is released because of overload 0x060B overload_congestion overload_congestion control Unsupported transmission medium requirement 0x0D03 serv_facil_not_implemented serv_facil_not_implemented received in IAM System has found that PCM is faulty 0x0824 pcm_faulty dual seizure, control in co-exchange 0x0B23 dual_seizure_both_w dual_seizure_both_way_crct ay_crct ICC rejects the call 0x060B overload_congestion overload_congestion ICC does not response to call setup 0x0603 no_response_from_co_proces no_response_from_co_proces RMA timeout 0x0603 no_response_from_co_proces no_response_from_co_proces traffic is reduced due to signalling link congestion 0x0851 scc_congestion SI7 has no resources to handle the call 0x0719 no_resource_for_call Information request timer T33 expires 0x0A0B inquiry_time_out inquiry_time_out UCIC received (if UCIC is supported) 0x0825 n_unknown_circuit → → → → → → →
→ →
→ → →
→ →
→
→
→ → → → → → → → →
9.1.3 Calling party category mapping MESSAGES MESSA GES MESSA MES SAGE GE IDE IDENTI NTIFIE FIER R INITIAL INITIAL ADDRESS ADDRESS01 01 © Nokia Siemens Networks
DN0124783, issue 5-0
ISUP mapping
80/114
INFO INFOR RMATION TION
04
EXTERNAL CATEGORY VALUES VALUES NUMBER (Hex/Dec) (Hex/Dec) unknown 0x00/00 opera erator, tor, langu nguage Fre French 0x01/0 1/01 opera erator, tor, langu nguage Engli glish 0x02/0 2/02 opera erator, tor, langu nguage Ger German man 0x03/0 3/03 oper operat ato or, lang langua uage ge Russ Russia ian n 0x04 0x04/0 /04 4 oper operat ato or, lang langua uage ge Span Spanis ish h 0x05 0x05/0 /05 5 ordin rdina ary call calliing subs subsc crib riber 0x0A/10 A/10 call callin ing g subs subscr crib ib.. with ith prio priori rity ty 0x0B 0x0B/1 /11 1 data call 0x0C/12 test call 0x0D/13 payphone 0x0F/15 Mapping of the internal category to external category hex/ dec INTE INTERNA RNAL L (CC) CAT CATEGORY EGORY hex/ dec EXTERNAL CATEGORY CATEGORY 0x00/00 0x00/00 ordinary ordinary_1_c _1_c 0x0A/10 ordinary calling calling subscr. 0x04/04 0x04/04 data_line data_line_c _c 0x0C/12 data call 0x05/05 0x05/05 pay_pho pay_phone_c ne_c 0x0F/15 0x0F/15 payphone payphone 0x08/08 0x08/08 priority_ priority_1_c 1_c 0x0B/11 calling subs. subs. with prior. prior. 0x10/16 0x10/16 test_equip test_equipment_ ment_c c 0x0D/13 test call 0x27/39 0x27/39 oper_fre_ oper_fre_c c 0x01/01 0x01/01 operator, operator, lang. lang. French 0x28/40 0x28/40 oper_en oper_eng_c g_c 0x02/02 operator, lang. English 0x29/41 0x29/41 oper_ger oper_ger_c _c 0x03/03 0x03/03 operator, operator, lang. lang. German 0x2A/42 0x2A/42 oper_rus_ oper_rus_c c 0x04/04 operator, lang. Russian 0x2B/43 0x2B/43 oper_spa oper_spa_c _c 0x05/05 operator, lang. Spanish 0xFF/255 unknown_c 0x00/00 0x00/00 unknown unknown Other internal categories 0x0A/10 ordinary calling calling subscr. →
→ → → → → → → → → → → →
Mapping of external category to internal category phase 1 (SS mapping) hex/ dec EXTERNAL CATEGORY hex/ dec INTE INTERNA RNAL L (CC) CATEGORY 0x00/00 0x00/00 unknown unknown 0xFF/255 unknown_c 0x01/01 operator, lang. French 0x27/39 0x27/39 oper_fre_ oper_fre_c c 0x02/02 operator, lang. English 0x28/40 0x28/40 oper_en oper_eng_c g_c 0x03/03 0x03/03 operator operator,, lang. German German 0x29/41 0x29/41 oper_ger_ oper_ger_c c 0x04/04 operator, lang. Russian 0x2A/42 0x2A/42 oper_rus_ oper_rus_c c 0x05/05 operator, lang. Spanish 0x2B/43 0x2B/43 oper_spa oper_spa_c _c 0x0A/10 ordinary calling calling subscr. subscr. 0x00/00 0x00/00 ordinary ordinary_1_c _1_c 0x0B/11 calling sub. sub. with prior. prior. 0x08/08 0x08/08 priority_ priority_1_c 1_c 0x0C/12 data call 0x04/04 0x04/04 data_line data_line_c _c 0x0D/13 test call 0x10/16 0x10/16 test_equip test_equipment_ ment_c c 0x0F/15 payphone 0x05/05 0x05/05 pay_phon pay_phone_c e_c Other external categories 0x00/00 0x00/00 ordinary ordinary_1_c _1_c →
→ → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
81/114
ISUP mapping
Mapping of external category to internal category phase 2 (CC mapping) hex/ dec INTERNAL (CC) CATEGORY INTERNAL (MML) CATEGORY 0x00/00 ordinary_1_c ordinary subscriber 0x04/04 data_line_c data call 0x05/05 pay_phone_c pay phone 0x08/08 priority_1_c subscriber with priority 0x10/16 test_equipment_c test phone 0x27/39 oper_fre_c operator call 0x28/40 oper_eng_c operator call 0x29/41 oper_ger_c operator call 0x2A/42 oper_rus_c operator call 0x2B/43 oper_spa_c operator call 0xFF/255 unknown_c unknown category Other external categories ordinary subscriber → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
DPNSS mapping
82/114
10 DPNSS mapping 10.1.1
Signalling
Digital Private Network Signalling System No 1 /BTNR 188
10.1.2
Cause code mapping
MESSAGES NUMBER Clear Request Message CRM 08 Clear Indication Message CIM 08 Recall Rejection Message RRM 0A Single-Channel Clear Indication Message SCIM 05 (not supported) Single-Channel Clear Request Message SCRM04 (not supported) Link-by-Link Reject Message LLRM 42 (not supported) Link Maintenance Reject Message LMRM46 (not supported) EXTERNAL CAUSE CODES NUMBER (Hex) Access Barred AB 0x29 Acknowledgement ACK 0x14 (used with virtual calls) Address Incomplete AI 0x01 Busy BY 0x08 Channel Out Of Service CHOS 0x23 DTE Controlled Not Ready CNR 0x2D Congestion CON 0x07 Call Termination CT 0x30 Facility Not Registered FNR 0x18 Incoming Calls Barred ICB 0x0A Service Incompatible INC 0x13 Message Not Understood MNU 0x1A Network Address Extension ErrorNAE-E 0x1E Network Termination NT 0x02 Number Unobtainable NU 0x00 Priority Forced Release PFR 0x24 Reject REJ 0x19 (used with virtual calls) Route Out Of Service ROS 0x1C Subscriber Incompatible SI 0x04 Signal Not Understood SNU 0x15 Signal Not Valid SNV 0x16 (not supported) Subscriber Out Of Service SOS 0x09 Signalling System Incompatible SSI 0x1B Service Temporarily Unavailable STU 0x17 Service Unavailable SU 0x03
© Nokia Siemens Networks
DN0124783, issue 5-0
83/114
Transferred DTE Uncontrolled Not Ready
DPNSS mapping TRFD 0x1D UNR 0x2E
(not supported)
Mapping of internal clear code to external cause code hex INTERNAL CLEAR CODE hex EXTERNAL CAUSE CODE 0x0000 normal_end_of_the_call 0x30 Call Termination (real call) 0x0000 normal_end_of_the_call 0x14 Acknowledgement (virtual call) 0x0004 b_subscri_busy_or_congest 0x08 Busy 0x0005 b_subscriber_busy 0x08 Busy 0x0005 b_subscriber_busy 0x30 Call Termination 0x0006 b_answer_time_out 0x02 Network Termination 0x0006 b_answer_time_out 0x30 Call Termination 0x0008 b_not_connected 0x09 Subscriber Out Of Service 0x0010 absent_subscriber 0x09 Subscriber Out Of Service 0x0011 operator_priority_access 0x24 Priority Forced Release 0x0012 no_paging_response 0x09 Subscriber Out Of Service 0x0021 b_busy_ccbs_possible 0x08 Busy 0x0022 b_busy_ccbs_not_possible 0x08 Busy 0x0106 bor_configuration_failure 0x19 Reject (virtual call) 0x0203 b_channel_unacceptable 0x23 Channel Out Of Service 0x0204 established_channel 0x23 Channel Out Of Service 0x0205 radio_if_congestion 0x07 Congestion 0x0206 call_rejected 0x02 Network Termination (real call) 0x0206 call_rejected 0x30 Call Termination (real call) 0x0206 call_rejected 0x19 Reject (virtual call) 0x0207 subscriber_congestion 0x08 Busy 0x020E a_line_vacant 0x30 Call Termination 0x0300 restrict_in_out_direction 0x29 Access Barred 0x0301 oper_restr_in_out_direct 0x29 Access Barred 0x0304 b_line_out_of_service 0x09 Subscriber Out Of Service 0x0305 b_line_faulty 0x09 Subscriber Out Of Service 0x0306 b_calls_restricted 0x0A Incoming Calls Barred 0x0307 b_number_unused 0x00 Number Unobtainable 0x0308 b_number_changed 0x00 Number Unobtainable 0x030A cl_a_onhook_set_up_phase 0x30 Call Termination 0x030B cl_a_onhook_answer_phase 0x30 Call Termination 0x030E b_line_blocked 0x09 Subscriber Out Of Service 0x0310 cug_reject 0x29 Access Barred 0x0311 bearer_serv_not_prov 0x13 Service Incompatible 0x0312 tele_serv_not_prov 0x14 Subscriber Incompatible 0x0313 illegal_subscriber 0x00 Number Unobtainable 0x0314 unidentified_subscriber 0x00 Number Unobtainable 0x0315 call_diversion_barring 0x29 Access Barred 0x0400 attenuator_congestion 0x07 Congestion 0x0401 interw_unit_congestion 0x07 Congestion → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
84/114
DPNSS mapping
0x0402 regist_total_time_exceeded 0x0403 mfcu_congestion 0x0404 pbru_congestion 0x0408 b_number_overflow 0x040D unallocated_roaming_number 0x040E roaming_not_allowed 0x050B module_rou_ssw_congestion 0x0601 module_link_congestion 0x0602 register_congestion 0x0604 intern_call_link_congestio 0x0606 conferen_device_congestion 0x060B overload_congestion 0x060C no_free_call_record_found 0x060D stage_circuit_congestion 0x0801 original_b_number_overflow 0x0802 a_number_overflow 0x0803 invalid_subscri_a_category 0x0804 outgoing_circ_congestion 0x0806 a_identity_not_available 0x080A r2_err_signal_from_in_crct 0x080C unknown_incoming_dec_sign 0x080D out_circuit_out_of_order 0x080E in_circuit_out_of_order 0x080F circuit_congestion 0x0810 facility_not_supported 0x0813 switching_equ_congestion 0x0814 circuit_group_congestion 0x0815 b_access_barred 0x0817 n_unallocated_number 0x0818 n_line_out_of_service 0x081A terminal_congestion 0x0820 n_msg_content_error 0x0A02 trunk_circ_invalid_msg 0x0A08 destinat_sign_out_of_order 0x0A0C Digital_path_not_provided 0x0B0F changed_b_number_overflow 0x0B18 service_unavailable 0x0B17 address_incomplete 0x0B19 service_incompatible 0x0B20 nae_error 0x0B21 dte_uncontrolled 0x0C00 dial_wait_time_exceeded 0x0C01 prohibited_dialling 0x0C02 insufficient dialling 0x0C0A serv_facil_usage_restrict © Nokia Siemens Networks
→ → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x01 Address Incomplete 0x07 Congestion 0x07 Congestion 0x00 Number Unobtainable 0x00 Number Unobtainable 0x03 Service Unavailable 0x07 Congestion 0x07 Congestion 0x07 Congestion 0x07 Congestion 0x07 Congestion 0x07 Congestion 0x07 Congestion 0x07 Congestion 0x00 Number Unobtainable 0x00 Number Unobtainable 0x04 Subscriber Incompatible 0x07 Congestion 0x03 Service Unavailable 0x01 Address Incomplete 0x15 Signal Not Understood 0x23 Channel Out Of Service 0x23 Channel Out Of Service 0x07 Congestion 0x18 Facility Not Registered 0x07 Congestion 0x07 Congestion 0x29 Access Barred 0x00 Number Unobtainable 0x09 Subscriber Out Of Service 0x07 Congestion 0x15 Signal Not Understood 0x1A Message Not Understood 0x1B Signalling System Incompatible 0x13 Service Incompatible 0x00 Number Unobtainable 0x03 Service Unavailable 0x01 Address Incomplete 0x13 Service Incompatible 0x1E Network Address Extension Error 0x2E DTE Uncontrolled Not Ready 0x01 Address Incomplete 0x00 Number Unobtainable 0x01 Address Incomplete 0x03 Service Unavailable DN0124783, issue 5-0
85/114
DPNSS mapping
0x0C0B inconsist_between_a_and_b 0x0D03 serv_facil_not_implemented 0x0D04 subs_sig_protocol_error 0x100D cf_uncon_notif_to_a 0x100E cf_uncon_no_notif_to_a 0x100F cf_ms_not_reach_notif_to_a 0x1010 cf_ms_not_reach_no_notif_a 0x1011 cf_ms_busy_notif_to_a 0x1012 cf_ms_busy_no_notif_to_a 0x1013 cf_ms_not_reply_notif_to_a 0x1014 cf_ms_not_reply_no_notif_a 0x1018 adr_complete 0x1019 adr_complete_no_charge 0x101A adr_complete_tracing 0x101B adr_comp_no_charge_tracing 0x101C adr_complete_coinbox 0x101D b_busy_through_connect 0x1020 b_modem_subs_unobtainable 0x1021 subs_call_term_to_network Other internal causes
→ → → → → → → → → → → → → → → → → → → →
0x04 Subscriber Incompatible 0x03 Service Unavailable 0x15 Signal Not Understood 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination 0x08 Busy 0x03 Service Unavailable 0x30 Call Termination 0x02 Network Termination (real call) 0x19 Rejected (virtual call)
Mapping of external cause code to internal clear code hex EXTERNAL CAUSE CODE hex INTERNAL CLEAR CODE 0x00 Number Unobtainable 0x0817 n_unallocated_number 0x01 Address Incomplete 0x0B17 address_incomplete 0x02 Network Termination 0x0A05 crct_released_by_co_exc 0x03 Service Unavailable 0x0B18 service_unavailable 0x04 Subscriber Incompatible 0x0C0B inconsist_between_a_and_b 0x07 Congestion 0x081A terminal_congestion 0x08 Busy 0x0005 b_subscriber_busy 0x09 Subscriber Out Of Service 0x0818 n_line_out_of_service 0x0A Incoming Calls Barred 0x0815 b_access_barred 0x13 Service Incompatible 0x0B19 service_incompatible 0x14 Acknowledgement 0x0015 normal_unspecified 0x15 Signal Not Understood 0x0820 n_msg_content_error 0x16 Signal Not Valid 0x0820 n_msg_content_error 0x17 Service Temporarily Unavailable 0x0C0A serv_facil_usage_restrict 0x18 Facility Not Registered 0x0810 facility_not_supported 0x19 Reject 0x0206 call_rejected 0x1A Message Not Understood 0x0A02 trunk_circ_invalid_msg 0x1B Signalling System Incompatible 0x0C0B inconsist_between_a_and_b 0x1CRoute Out Of Service 0x0814 circuit_group_congestion 0x1DTransferred 0x0000 normal_end_of_the_call 0x1E Network Address Extension Error 0x0B20 nae_error → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
86/114
0x23 Channel Out Of Service 0x23 Channel Out Of Service 0x24 Priority Forced Release 0x29 Access Barred 0x2D DTE Controlled Not Ready 0x2E DTE Uncontrolled Not Ready 0x30 Call Termination 0x30 Call Termination 0x30 Call Termination Other external causes
DPNSS mapping → → → → → → → → → →
0x080E in_circuit_out_of_order 0x080D out_circuit_out_of_order 0x0011 operator_priority_access 0x0815 b_access_barred 0x0207 subscriber_congestion 0x0B21 dte_uncontrolled 0x0000 normal_end_of_the_call 0x030A cl_a_onhook_set_up_phase 0x030B cl_a_onhook_answer_phase 0x0015 normal_unspecified
Internal cause codes generated by DPNSS 1 hex INTERNAL FAILURE DESCRIPTIONS hex INTERNAL CLEAR CODE 0002H Reading of PCMCON file fails 0x0509 file_error 0003H Reading of LSIGNL file fails 0x0509 file_error 0004H Reading of CRSPRI file fails 0x0509 file_error 0002H Timer expires in RMA library routine 0x0603 no_response_from_co_proces 0003H CC ack timer expires 0x0603 no_response_from_co_proces 0002H Call is cleared by MML command 0x0609 call_cleared_by_mml 0003H ET-unit state was changed by user 0x0609 call_cleared_by_mml 0002H ECU state changed 0x0610 ec_failure 0002H RFRPRB clears the call 0x070A forced_clear_of_a_call 0003H TIME QUOTA expires 0x070A forced_clear_of_a_call 0004H Circuit has been set to NU state 0x070A forced_clear_of_a_call 0002H Attempt to make a outgoing call to incoming 0x070E configuration_error circuit 0003H Parameter DCS forgotten in CGR creation, 0x070E configuration_error Circuit not found from CRSPRI 0002H Creation of a hand fails 0x0719 no_resource_for_call 0002H Packing of ISRM message fails 0x0811 network_failure 0003H Packing of SSRM message fails 0x0811 network_failure 0004H Packing of ISRM message fails, the call is in 0x0811 network_failure transit mode 0002H Buffer reservation fails 0x081A terminal_congestion 0002H Unpacking of received CRM message fails 0x0820 n_msg_content_error 0003H Unpacking of received SSRM message fails 0x0820 n_msg_content_error 0004H Unpacking of received NAM message fails 0x0820 n_msg_content_error 0006H Unpacking of received NIM message fails 0x0820 n_msg_content_error 0007H Unpacking of received CCM message fails 0x0820 n_msg_content_error 0008H Unrecognized mandatory string in ISRM or 0x0820 n_msg_content_error SSRM message 0002H PCM service manager clears the call 0x0824 pcm_faulty 0003H ET state changed by system 0x0824 pcm_faulty 0004H DLC is down 0x0824 pcm_faulty 0002H SSRM timer expires 0x0B17 adress_incomplete → → → → → → → → → → → →
→
→ → → →
→ → → → → → →
→ → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
DPNSS mapping
87/114
0002H BC or LLC is not supported 0002H Dual seizure, incoming call 0003H Dual seizure, outgoing call 0002H Invalid called number
10.1.3
→ → → →
0x0B18 service_unavailable 0x0B23 dual_seizure_both_way_crct 0x0B23 dual_seizure_both_way_crct 0x0C01 prohibited_dialling
Calling party category mapping
MESSAGES NUMBER (Hex/Dec) Initial service request message (C) 0x00/0 ISRM(C) Initial service request message (I) 0x01/1 ISRM(I) Call connected message 0x05/5 CCM Number acknowledge message 0x09/9 NAM Subsequent service request message (I) 0x0B/11 SSRM(I) Subsequent service request message (C) 0x0C/12 SSRM(C) End-to-end message (C) 0x22/34 EEM(C) End-to-end message (I) 0x23/35 EEM(I) EXTERNAL CATEGORY VALUES NUMBER (Hex/Dec) ordinary 0x31/1 decadic 0x32/2 dass 2 0x33/3 pstn 0x34/4 ssmf5 0x35/5 operator 0x36/6 network ( not used ) conference ( not used )
NOTE Decimal numbers are encoded in ASCII
Mapping of the internal category to external category hex/ dec CC CATEGORY hex/ dec EXTERNAL CATEGORY 0x41/65 cc_pbx_c 0x32/2 decadic 0x41/65 cc_pbx_c (number incl) 0x31/1 ordinary 0x42/66 cc_pnp_c 0x32/2 decadic 0x42/66 cc_pnp_c (number incl) 0x31/1 ordinary Other configurations 0x34/4 pstn Other configurations (number incl) 0x33/3 dass →
NOTE © Nokia Siemens Networks
DN0124783, issue 5-0
DPNSS mapping
88/114
Different mapping when no number is included in message.
Mapping of external category to internal category phase 1 (SS mapping) hex/dec EXTERNAL CATEGORY hex/ dec CC CATEGORY 0x31/1 ordinary 0x00/00 ordinary_1_c 0x32/2 decadic 0x36/54 pbx_dec_c 0x33/3 dass 2 0x35/53 pbx_dass_c 0x34/4 pstn 0x34/52 pstn_c 0x35/5 ssmf5 0x37/55 pbx_mf5_c 0x36/6 operator 0x11/17 operator_c 0x37/7 network ( not used ) 0x38/8 conference ( not used ) →
Mapping of external category to internal category phase 2 (CC mapping) hex/dec CC CATEGORY hex/ dec INTERNAL CATEGORY 0x00/00 ordinary_1_c ordinary subscriber 0x11/17 operator_c operator 0x34/55 pstn_c ordinary subscriber 0x35/53 pbx_dass_c ordinary subscriber 0x36/54 pbx_dec_c ordinary subscriber 0x37/55 pbx_mf5_c ordinary subscriber →
→ → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
30B+D mapping
89/114
11 30B+D mapping 11.1.1
Signalling
Digital Subscriber Signalling System No 1.
11.1.2
Cause code mapping
MESSAGES NUMBER Disconnect 45 Release 4D Release Complete5A EXTERNAL CAUSE CODES unallocated number no route to specified transit network no route to destination channel_unacceptable call awarded and being delivered in an established channel normal call clearing user busy no user responding no answer from user (user alerted) subscriber absent call rejected number changed non-selected user clearing destination out of order invalid number format facility rejected response to STATUS ENQUIRY normal unspecified no circuit/channel available network out of order temporary failure switching equipment congestion access information discarded requested circuit/channel not available resources unavailble, unspecified quality of service unavailable requested facility not subscribed bearer capability not authorized bearer capability not presently available © Nokia Siemens Networks
NUMBER (hex/dec) 0x01/01 0x02/02 0x03/03 0x06/06 0x07/07 0x10/16 0x11/17 0x12/18 0x13/19 0x14/20 0x15/21 0x16/22 0x1A/26 0x1B/27 0x1C/28 0x1D/29 0x1E/30 0x1F/31 0x22/34 0x26/38 0x29/41 0x2A/42 0x2B/43 0x2C/44 0x2F/47 0x31/49 0x32/50 0x39/57 0x3A/58 DN0124783, issue 5-0
30B+D mapping
90/114
service or option not available, unspecified bearer capability not implemented channel type not implemented requested facility not implemented only restricted digital information bearer capability is available service or option not implemented, unspecified invalid call reference value identified channel does not exist a suspended call exists, but this call identity does not call identity in use no call suspended call having the requested call identity has been cleared user not member of cug incompatible destination invalid transit network selection invalid message, unspecified mandatory information element is missing message type non-existent or not implemented message not compatible with call state or message type non-existent or not implemented information element non-existent or not implemented invalid information element contents message not compatible with call state recovery on timer expiry protocol error, unspecified interworking unspecified
hex 0x0000 0x0005 0x0006 0x0010 0x0012 0x0021 0x0022 0x0106 0x0201 0x0203 0x0204 0x0206 0x0213 0x0304 0x0306 0x0307
0x3F/63 0x41/65 0x42/66 0x45/69 0x46/70 0x4F/79 0x51/81 0x52/82 0x53/83 0x54/84 0x55/85 0x56/86 0x57/87 0x58/88 0x5B/91 0x5F/95 0x60/96 0x61/97 0x62/98 0x63/99 0x64/100 0x65/101 0x66/102 0x6F/111 0x7F/127
Mapping of internal clear code to external cause code INTERNAL CLEAR CODE hex/dec EXTERNAL CAUSE CODE normal_end_of_the_call 0x10/16 normal_call_clearing b_subscriber_busy 0x11/17 user_busy b_answer_time_out 0x13/19 no_answer_from_user absent_subscriber 0x14/20 subscriber_absent no_paging_response 0x14/20 subscriber_absent b_busy_ccbs_possible 0x11/17 user_busy b_busy_ccbs_not_possible 0x11/17 user_busy bor_configuration_failure 0x95/149 call_rejected call_released 0x10/16 normal_call_clearing b_channel_unacceptable 0x06/06 ch_unacceptable established_channel 0x07/07 call_delvd_in_est_ch call_rejected 0x15/21 call_rejected n_user_not_in_cug 0x57/87 user_not_member_of_cug b_line_out_of_service 0x1B/27 dest_out_of_order b_calls_restricted 0x1A/26 non_selected_user_clrng b_number_unused 0x01/01 unalloc_num
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → →
DN0124783, issue 5-0
91/114
0x0308 b_number_changed 0x030A cl_a_onhook_set_up_phase 0x030B cl_a_onhook_answer_phase 0x030C b_onhook_time_out 0x030E b_line_blocked 0x0310 cug_reject 0x031A cug_rej_icb 0x031C cug_rej_not_member 0x031D cug_rej_ocb 0x031E cug_rej_ind_not_comp_bs 0x031F cug_rej_bs_violation 0x0320 cug_rej_ss_violation 0x0321 cug_rej_no_cug_selected 0x0322 cug_rej_unknown_cug_ind 0x060C no_free_call_record_found 0x0715 facility_not_avail_on_outr 0x0804 outgoing_circ_congestion 0x080F circuit_congestion 0x0810 facility_not_supported 0x0811 network_failure 0x0813 switching_equ_congestion 0x0814 circuit_group_congestion 0x0815 b_access_barred 0x0817 n_unallocated_number 0x0818 n_line_out_of_service 0x0819 n_subscriber_nbr_changed 0x0820 n_msg_content_error 0x0821 invalid_transit_n_select 0x0822 n_recovery_timer_expiry 0x0A02 trunk_circ_invalid_msg 0x0A03 interworking_failed 0x0A04 trunk_circ_protocol_error 0x0A05 crct_released_by_co_exc 0x0A09 address_complete_time_out 0x0A0C digital_path_not_provided 0x0A0D no_route_to_destination 0x0B17 adress_incomplete 0x0B2B param_no_exist_or_impl 0x0C02 insufficient_dialling 0x0C09 serv_facil_activa_restrict 0x0C0A serv_facil_usage_restrict 0x0C0B inconsist_between_a_and_b 0x0D00 subs_signa_msg_content_err 0x0D01 subs_signa_msg_format_err 0x0D03 serv_facil_not_implemented © Nokia Siemens Networks
30B+D mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x16/22 num_changed 0x10/16 normal_call_clearing 0x10/16 normal_call_clearing 0x66/102 recovery on timer expiry 0x1B/27 dest_out_of_order 0x1D/29 facility_rejected 0x1D/29 facility_rejected 0x57/87 user_not_member_of_cug 0x1D/29 facility_rejected 0x1D/29 facility_rejected 0x57/87 user_not_member_of_cug 0x1D/29 facility_rejected 0x1D/29 facility_rejected 0x1D/29 facility_rejected 0x2F/47 resources_unavail 0x2F/47 resources_unavail 0x22/34 no_circuit_or_ch_avail 0x22/34 no_circuit_or_ch_avail 0x45/69 reqd_fac_not_implemtd 0x29/41 temporary_failure 0x2A/42 switch_equipment_congestn 0x22/34 no_circuit_or_ch_avail 0x58/88 incompat_dest 0x01/01 unalloc_num 0x1B/27 dest_out_of_order 0x16/22 num_changed 0x64/100 invld_info_elem_contents 0x5B/91 invld_trans_netwk_selectn 0x66/102 recovery on timer expiry 0x61/97 msg_typ_not_implemtd 0x7F/127 interworking_unspec 0x6F/111 protocol_error 0x26/38 netwk_out_of_order 0x01/01 unalloc_num 0x41/65 bearer_cap_n_im_c 0x03/03 no_rte_2_dest 0x1C/28 invalid_num_fmt 0x63/99 info_elem_not_implemtd 0x1C/28 invalid_num_fmt 0x32/50 req_facility_not_subscribed 0x3F/63 service_or_opt_unavail_unspec 0x58/88 incompat_dest 0x64/100 invld_info_elem_contents 0x60/96 mand_info_elem_missing 0x41/65 bearer_capability_not_implemented DN0124783, issue 5-0
92/114
0x0D04 subs_sig_protocol_error 0x0D07 no_user_responding 0x0D0F facility_rejected other internal causes
30B+D mapping → → → →
0x65/101 msg_not_compat_with_state 0x12/18 no_user_responding 0x1D/29 facility_rejected 0x1F/31 normal_unspecified
Mapping of external cause code to internal clear code hex/dec EXTERNAL CAUSE CODE hex INTERNAL CLEAR CODE 0x01/01 unalloc_num 0x0817 n_unallocated_number 0x02/02 no_rte_2_spec_trans_netwk 0x0A0D no_route_to_destination 0x03/03 no_rte_2_dest 0x0A0D no_route_to_destination 0x06/06 ch_unacceptable 0x0203 b_channel_unacceptable 0x07/07 call_delvd_in_est_ch 0x0204 established_channel 0x10/16 normal_call_clearing 0x0000 normal_end_of_the_call 0x10/16 normal_call_clearing 0x030A cl_a_onhook_set_up_phase 0x10/16 normal_call_clearing 0x030B cl_a_onhook_answer_phase 0x10/16 normal_call_clearing 0x0015 normal_unspecified 0x11/17 user_busy 0x0005 b_subscriber_busy 0x12/18 no_user_responding 0x0D07 no_user_responding 0x13/19 no_answer_from_user 0x0006 b_answer_time_out 0x14/20 subscriber_absent 0x0010 absent_subscriber 0x15/21 call_rejected 0x0206 call_rejected 0x16/22 num_changed 0x0819 n_subscriber_nbr_changed 0x1A/26 non_selected_user_clrng 0x0201 call_released 0x1B/27 dest_out_of_order 0x0818 n_line_out_of_service 0x1C/28 invalid_num_fmt 0x0B17 adress_incomplete 0x1D/29 facility_rejected 0x0D0F facility_rejected 0x1E/30 response_2_status_enq 0x0201 call_released 0x1F/31 normal_unspecified 0x0015 normal_unspecified 0x22/34 no_circuit_or_ch_avail 0x080F circuit_congestion 0x26/38 netwk_out_of_order 0x0A05 crct_released_by_co_exc 0x29/41 temporary_failure 0x0811 network_failure 0x2A/42 switch_equipment_congestn 0x0813 switching_equ_congestion 0x2C/44 reqd_ckt_or_ch_not_avail 0x080F circuit_congestion 0x2F/47 resources_unavail_unspec 0x080F circuit_congestion 0x31/49 quality_of_service_unavail 0x0D03 serv_facil_not_implemented 0x32/50 req_facility_not_subscribed 0x0C09 serv_facil_activa_restrict 0x39/57 bearer_cap_not_authorized 0x0C09 serv_facil_activa_restrict 0x3A/58 bearer_cap_pres_not_avail 0x0C0A serv_facil_usage_restrict 0x3F/63 service_or_opt_unavail_unspec 0x0C0A serv_facil_usage_restrict 0x41/65 bearer_cap_not_implemtd 0x0D03 serv_facil_not_implemented 0x42/66 ch_typ_not_implemtd 0x0203 b_channel_unacceptable 0x45/69 reqd_fac_not_implemtd 0x0810 facility_not_supported 0x46/70 only_restr_digital_info_avail 0x0A0C digital_path_not_provided 0x4F/79 service_or_opt_not_implemtd 0x0D03 serv_facil_not_implemented 0x51/81 invld_call_ref_value 0x0820 n_msg_content_error → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
93/114
30B+D mapping
0x52/82 identified_ch_not_exist 0x57/87 user_not_member_of_cug 0x58/88 incompat_dest 0x5B/91 invld_trans_netwk_selectn 0x5F/95 invld_msg 0x60/96 mand_info_elem_missing 0x61/97 msg_typ_not_implemtd 0x62/98 msg_not_compat_or_not_implemtd 0x63/99 info_elem_not_implemtd 0x64/100 invld_info_elem_contents 0x65/101 msg_not_compat_with_state 0x66/102 recvry_on_timer_expiry 0x6F/111 protocol_error 0x7F/127 interworking_unspec other external causes
→ → → → → → → → → → → → → → →
0x0203 b_channel_unacceptable 0x0213 n_user_not_in_cug 0x0C0B inconsist_between_a_and_b 0x0821 invalid_transit_n_select 0x0A02 trunk_circ_invalid_msg 0x0D01 subs_signa_msg_format_err 0x0A02 trunk_circ_invalid_msg 0x0D0D msg_not_cmtbl_or_impl 0x0B2B param_no_exist_or_impl 0x0D00 subs_signa_msg_content_err 0x0D04 subs_sig_protocol_error 0x0822 n_recovery_timer_expiry 0x0A04 trunk_circ_protocol_error 0x0A03 interworking_failed 0x0015 normal_unspecified
Internal cause codes generated by digital subscriber signalling system No 1 INTERNAL FAILURE DESCRIPTIONS hex INTERNAL CLEAR CODE CONNECT message was not received from PBX 0x0006 b_answer_time_out within T301 External cause was missing from the first clearing 0x0015 normal_unspecified message External cause received in first clearing message 0x0015 normal_unspecified was corrupted Error occured during file reading 0x0509 file_error No response from co-process within protection timer 0x0603 no_response_from_co_proces RMA timeout,circuit and call id reservation failed 0x0603 no_response_from_co_proces Call was cleared by MML 0x0609 call_cleared_by_mml ET-unit state was changed by user 0x0609 call_cleared_by_mml Ticket request rejected 0x060B overload_congestion Ticket request timer expires 0x060B overload_congestion RMA call id reservation rejected because ticket 0x060C no_free_call_record_found service is overloaded Clear call request from IWMANA (ECU restart or 0x0610 ec_failure state change) Clear call request from RFR 0x070A forced_clear_of_a_call CRSPRI file did not contain wanted PCM value 0x070E configuration_error Creation of a B-channel handler fails 0x0719 no_resource_for_call Incoming call rejected because of circuit congestion 0x080F circuit_congestion Call to blocked circuit was cleared 0x080F circuit_congestion Required uus1 request is rejected 0x0810 facility_not_supported No response to required uus1 request 0x0810 facility_not_supported Required uus2 request is rejected 0x0810 facility_not_supported No response to required uus2 request 0x0810 facility_not_supported Required uus3 request is rejected 0x0810 facility_not_supported →
→
→
→ → → → → → → →
→
→ → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
30B+D mapping
94/114
No response to required uus3 request Call was cleared because PCM was set out of use Memory buffer reservation fails DISCONNECT or RELEASE message contained illegal coded elements SETUP contained incompatible bearer service Bearer capability element was missing from SETUP DISCONNECT or RELEASE contained unknown information elements Overlap sending supervision T302 expired PCM faulty ET to TE in 30B+D Clear call request from PCM service manager process Signalling link is down Clear call request from PBX (RESTART-message received from PBX) Overlap receiving supervision T304 expired External cause in RELEASE was corrupted External cause was missing from RELEASE message Information element coded as comprehension required Received SETUP message with unimplemented Bearer Capability information element Received STATUS message with incompatible call state Received STATUS message with call state coded as NULL Response message was not received from network within T310
11.1.3
→ → → →
→ → →
→ → → →
→ →
0x0810 facility_not_supported 0x0811 network_failure 0x081A terminal_congestion 0x0820 n_msg_content_error 0x0820 n_msg_content_error 0x0820 n_msg_content_error 0x0820 n_msg_content_error 0x0822 n_recovery_timer_expiry 0x0824 pcm_faulty 0x0824 pcm_faulty 0x0824 pcm_faulty 0x0824 pcm_faulty 0x0A05 crct_released_by_co_exc
→
0x0B17 adress_incomplete 0x0D00 subs_signa_msg_content_err 0x0D01 subs_signa_msg_format_err
→
0x0D01 subs_signa_msg_format_err
→
0x0D03 serv_facil_not_implemented
→
0x0D04 subs_sig_protocol_error
→
0x0D04 subs_sig_protocol_error
→
0x0D07 no_user_responding
→ →
Calling party category mapping
There are no categories in Digital Subscriber Signalling system No 1. The only category involved is ordinary on the incoming side.
© Nokia Siemens Networks
DN0124783, issue 5-0
INAP mapping
95/114
12 INAP mapping 12.1.1
Signalling
INAP User Part (Core INAP) INAP operations containing the cause parameter are listed below.
OPERATIONS (from SCP to SSP)OPCODE ReleaseCall 22 CallGap 41 OPERATIONS (from SSP to SCP)OPCODE EventReportBCSM 24 EXTERNAL CAUSE CODES NUMBER (Hex/Dec) un_alloc_num_c 0x01/01 no_route_to_spec_nw_c 0x02/02 no_route_to_dest_c 0x03/03 send_spec_inf_tone_c 0x04/04 misdial_trunk_pref_c 0x05/05 preemption_c 0x08/08 preemption_crct_res_c 0x09/09 normal_call_clear_c 0x10/16 user_busy_c 0x11/17 no_user_responding_c 0x12/18 no_answer_fr_user_c 0x13/19 absent_subscriber_c 0x14/20 call_rejected_c 0x15/21 number_changed_c 0x16/22 dest_out_of_ord_c 0x1B/27 address_incomplete_c 0x1C/28 facility_rejected_c 0x1D/29 normal_unspecified_c 0x1F/31 no_circuit_avail_c 0x22/34 network_out_of_ord_c 0x26/38 temporary_failure_c 0x29/41 switching_eq_cong_c 0x2A/42 access_inf_disc_c 0x2B/43 req_chan_not_avail_c 0x2C/44 precedence_call_bl_c 0x2E/46 res_unavail_unspec_c 0x2F/47 req_facil_not_subsc_c 0x32/50 out_calls_barr_w_CUG_c 0x35/53
© Nokia Siemens Networks
DN0124783, issue 5-0
INAP mapping
96/114
in_calls_barr_w_CUG_c bear_cap_not_author_c bear_cap_no_pres_av_c incon_in_out_access_inf_c serv_not_av_unspec_c bear_cap_not_implem_c req_facil_not_imple_c only_res_dig_bc_av_c serv_opt_not_impl_c cd_user_not_in_CUG_c incompat_dest_c non_existent_cug_c inv_tran_nw_sel_c inv_msg_unspec_c msg_type_no_ex_imp_c parm_no_ex_imp_dis_c recovery_timer_exp_c parm_no_ex_imp_pas_c parm_no_ex_dis_msg_c protocl_erro_unspec_c in_service_discon_c in_charge_limit_exc_c interwork_unspecif_c
12.1.2 hex 0000 0005 0006 0010 0012 0013 0021 0022 0201 0202 0205 0206 0207 0212 0213 0300
0x37/55 0x39/57 0x3A/58 0x3E/62 0x3F/63 0x41/65 0x45/69 0x46/70 0x4F/79 0x57/87 0x58/88 0x5A/90 0x5B/91 0x5F/95 0x61/97 0x63/99 0x66/102 0x67/103 0x6E/110 0x6F/111 0x7D/125 0x7E/126 0x7F/127
Mapping table
Reason for mapping internal to external (from SSP to SCP) INTERNAL CLEAR CODE hex/ dec EXTERNAL CAUSE CODE Normal_end_of_the_call 0x10/16 normal_call_clear_c B_subscriber_busy 0x11/17 user_busy_c B_answer_time_out 0x13/19 no_answer_fr_user_c Absent_subscriber 0x14/20 absent_subscriber_c No_paging_response 0x12/18 no_user_responding_c Ct_recall_time_out 0x13/19 no_answer_fr_user_c B_busy_ccbs_possible 0x11/17 user_busy_c(Note 1) B_busy_ccbs_not_possible 0x11/17 user_busy_c(Note 2) Call_released 0x15/21 call_rejected_c Clear_request_rec_out_crct 0x10/16 normal_call_clear_c Radio_if_congestion 0x22/34 no_circuit_avail_c Call_rejected 0x15/21 call_rejected_c Subscriber_congestion 0x2f/47 res_unavail_unspec_c N_unknown_dialling 0x1c/28 address_incomplete_c N_user_not_in_cug 0x57/87 cd_user_not_in_CUG_c Restrict_in_out_direction 0x58/88 incompat_dest_c
© Nokia Siemens Networks
→ → → → → → → → → → → → → → → → →
DN0124783, issue 5-0
97/114
0304 B_line_out_of_service 0305 B_line_faulty 0306 B_calls_restricted 0307 B_number_unused 0308 B_number_changed 030A cl_a_onhook_set_up_phase 030B cl_a_onhook_answer_phase 030E b_line_blocked 0310 Cug_reject 0311 Bearer_serv_not_prov 0312 Tele_serv_not_prov 0313 Illegal_subscriber 0314 Unidentified_subscriber 0315 Call_diversion_barring 0316 Memory_capacity_exceeded 0317 In_service_time_exceeded 0319 Illegal_subscriber_station 031A cug_rec_icb 031C cug_rej_not_member 031D cug_rej_ocb 031F cug_rej_bs_violation 0320 Cug_rej_ss_violation 0401 interw_unit_congestion 0402 Regist_total_time_exceeded 0403 Mfcu_congestion 0404 Pbru_congestion 0406 Connect_failed_in_gsw_swi 0407 Err_answer_from_co_process 0408 B_number_overflow 040A traffic_type_congestion 040D unallocated_roaming_number 040E roaming_not_allowed 0508 Charging_error 0509 File_error 050C mfc_ass_chan_close_missed 0600 File_record_congestion 0603 No_response_from_co_proces 0606 Conferen_device_congestion 0608 Charging_not_started 060B overload_congestion 060E unit_restarted 0610 Ec_failure 0701 Register_analysis_failed 0706 Call_interrupt_in_reg_ana 070A forced_clear_of_a_call © Nokia Siemens Networks
INAP mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x1b/27 dest_out_of_ord_c 0x12/18 no_user_responding_c 0x58/88 incompat_dest_c 0x01/01 un_alloc_num_c 0x16/22 number_changed_c 0x10/16 normal_call_clear_c 0x10/16 normal_call_clear_c 0x12/18 no_user_responding_c 0x37/55 in_calls_barr_w_CUG_c 0x39/57 bear_cap_not_author_c 0x3f/63 serv_not_av_unspec_c 0x01/01 un_alloc_num_c 0x01/01 un_alloc_num_c 0x15/21 call_rejected_c 0x2f/47 res_unavail_unspec_c 0x66/102recovery_timer_exp_c 0x58/88 incompat_dest_c 0x37/55 in_calls_barr_w_CUG_c 0x57/87 cd_user_not_in_CUG_c 0x35/53 out_calls_bar_w_CUG_c 0x1d/29 facility_rejected_c 0x3e/62 incon_in_out_access_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x2a/42 switching_eq_conq_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c DN0124783, issue 5-0
98/114
070B modem_error 070D announcement_error 070E configuration_error 070F diu_pool_error 0719 No_resource_for_call 0804 Outgoing_circ_congestion 0807 R2_signal_pause_time_out 0808 R2_sign_backwards_time_out 0809 R2_err_signl_from_out_crct 080A r2_err_signal_from_in_crct 080D out_circuit_out_of_order 080E in_circuit_out_of_order 080F circuit_congestion 0810 Facility_not_supported 0811 Network_failure 0812 Map_failure 0813 Switching_equ_congestion 0814 Circuit_group_congestion 0815 B_access_barred 0816 Congestion_send_info_tone 0817 N_unallocated_number 0818 N_line_out_of_service 0819 N_subscriber_nbr_changed 081A terminal_congestion 081B no_hlr_response 081C no_vlr_response 081F n_overload_congestion 0820 N_msg_content_error 0821 Invalid_transit_n_select 0822 N_recovery_timer_expiry 0824 Pcm_faulty 0826 Unrec_param_msg_discarded 0900 No_mf_forward_signal 090D seizu_ack_time_out_in_crct 0A02 trunk_circ_invalid_msg 0A03 interworking_failed 0A04 trunk_circ_protocol_error 0A05 crct_released_by_co_exc 0A08 destinat_sign_out_of_order 0A09 address_complete_time_out 0A0C Digital_path_not_provided 0A0D no_route_to_destination 0B10 v110_frame_sync_fail 0B11 modem_communication_error 0B12 rlp_or_ms_frame_sync_error © Nokia Siemens Networks
INAP mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x29/41 temporary_failure_c 0x22/34 no_circuit_avail_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x22/34 no_circuit_avail_c 0x1d/29 facility_rejected_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x2a/42 switching_eq_conq_c 0x22/34 no_circuit_avail_c 0x58/88 incompat_dest_c 0x04/04 send_spec_inf_tone_c 0x01/01 un_alloc_num_c 0x1b/27 dest_out_of_ord_c 0x16/22 number_changed_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2a/42 switching_eq_conq_c 0x5f/95 inv_msg_unspec_c 0x5b/91 inv_tran_nw_sel_c 0x66/102recovery_timer_exp_c 0x2f/47 res_unavail_unspec_c 0x6e/110parm_no_ex_dis_msg_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x61/97 msg_type_no_ex_imp_c 0x7f/127 interwork_unspecif_c 0x6f/111 protocl_erro_unspec_c 0x26/38 network_out_of_ord_c 0x1b/27 dest_out_of_ord_c 0x01/01 un_alloc_num_c 0x46/70 only_res_dig_bc_av_c 0x03/03 no_route_to_dest_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c DN0124783, issue 5-0
INAP mapping
99/114
0B13 radio_if_failure 0B14 handover_failure 0B15 ciphering_not_succeeded 0B16 remote_equipment_failure 0B17 adress_incomplete 0B18 service_unavailable 0B19 service_incompatible 0B1A bssmap_protocol_error 0B1B radio_if_msg_failure 0B1C radio_if_fail_rev_to_old 0B20 nae_error 0B21 dte_uncontrolled 0B23 dual_seizure_both_way_crct 0B2A blocking_received 0B2B param_no_exist_or_impl 0B2C in_protocol_error 0B2D in_appl_response_time_out 0B2F in_tcap_error 0B30 asn1_codec_error 0B3E call_period_timeout 0C00 dial_wait_time_exceeded 0C01 prohibited_dialling 0C02 insufficient_dialling 0C09 serv_facil_activa_restrict 0C0A serv_facil_usage_restrict 0C0B inconsist_between_a_and_b 0C0D bc_not_presently_available 0D00 subs_signa_msg_content_err 0D01 subs_signa_msg_format_err 0D03 serv_facil_not_implemented 0D04 subs_sig_protocol_error 0D06 aocc_charging_error 0D07 no_user_responding 0D08 gsm_erh408_prot_timer_exp 0D0D msg_not_cmptbl_or_impl Other internal causes
→ → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x1c/28 address_incomplete_c 0x3f/63 serv_not_av_unspec_c 0x58/88 incompat_dest_c 0x6f/111 protocl_erro_unspec_c 0x6f/111 protocl_erro_unspec_c 0x29/41 temporary_failure_c 0x01/01 un_alloc_num_c 0x3f/63 serv_not_av_unspec_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x63/99 parm_no_ex_imp_dis_c 0x6f/111 protocl_erro_unspec_c 0x66/102recovery_timer_exp_c 0x6f/111 protocl_erro_unspec_c 0x6f/111 protocl_erro_unspec_c 0x66/102recovery_timer_exp_c 0x1c/28 address_incomplete_c 0x01/01 un_alloc_num_c 0x01/01 un_alloc_num_c 0x39/57 bear_cap_not_author_c 0x3f/63 serv_not_av_unspec_c 0x58/88 incompat_dest_c 0x3a/58 bear_cap_no_pres_av_c 0x6f/111 protocl_erro_unspec_c 0x6f/111 protocl_erro_unspec_c 0x41/65 bear_cap_not_implem_c 0x6f/111 protocl_erro_unspec_c 0x29/41 temporary_failure_c 0x12/18 no_user_responding_c 0x66/102recovery_timer_exp_c 0x61/97 msg_type_no_ex_imp_c 0x1F/31 normal_unspecified_c
NOTE 1 cause diagnostics value is set to 0x1 (CCBS possible) 2 © Nokia Siemens Networks
DN0124783, issue 5-0
INAP mapping
100/114
cause diagnostics value is set to 0x2 (CCBS not possible)
Reason for mapping external to internal (from SCP to SSP) hex/dec EXTERNAL CAUSE CODE hex INTERNAL CLEAR CODE 0x01/01 un_alloc_num_c 0817 n_unallocated_number 0x02/02 no_route_to_spec_nw_c 0A0D no_route_to_spec_nw 0x03/03 no_route_to_dest_c 0A0D no_route_to_destination 0x04/04 send_spec_inf_tone_c 0816 congestion_send_info_tone 0x05/05 misdial_trunk_pref_c 0817 n_unallocated_number 0x08/08 preemption_c 0015 normal_unspecified 0x09/09 preemption_circuit_res_c 0015 normal_unspecified 0x10/16 normal_call_clear_c 0000 normal_end_of_the_call 0x11/17 user_busy_c 0005 b_subscriber_busy 0x11/17 user_busy_c 0021 b_busy_ccbs_possible(Note 1) 0x11/17 user_busy_c 0022 b_busy_ccbs_not_possible(Note 2) 0x12/18 no_user_responding_c 0D07 no_user_responding 0x13/19 no_answer_fr_user_c 0006 b_answer_time_out 0x14/20 absent_subscriber_c 0010 absent_subscriber 0x15/21 call_rejected_c 0206 call_rejected 0x16/22 number_changed_c 0819 n_subscriber_nbr_changed 0x1B/27 dest_out_of_ord_c 0818 n_line_out_of_service 0x1C/28 address_incomplete_c 0B17 address_incomplete 0x1D/29 facility_rejected_c 0810 facility_not_supported 0x1F/31 normal_unspecified_c 0015 normal_unspecified 0x22/34 no_circuit_avail_c 080F circuit_congestion 0x26/38 network_out_of_ord_c 0A05 crct_released_by_co_exc 0x29/41 temporary_failure_c 0811 network_failure 0x2A/42 switching_eq_cong_c 0813 switching_equ_congestion 0x2B/43 access_inf_disc_c 0015 normal_unspecified 0x2C/44 req_chan_not_avail_c 080F circuit_congestion 0x2E/46 precedence_call_bl_c 0811 network_failure 0x2F/47 res_unavail_unspec_c 080F circuit_congestion 0x32/50 req_facil_not_subsc_c 0C09 serv_facil_activa_restrict 0x35/53 out_calls_barr_w_CUG_c 031D cug_rej_ocb 0x37/55 in_calls_barr_w_CUG_c 0310 cug_reject 0x39/57 bear_cap_not_author_c 0C09 serv_facil_activa_restrict 0x3A/58 bear_cap_no_pres_av_c 0C0D bc_not_presently_available 0x3E/62 incon_in_out_access_inf_c 0320 cug_rej_ss_violation 0x3F/63 serv_not_av_unspec_c 0C0A serv_facil_usage_restrict 0x41/65 bear_cap_not_implem_c 0D03 serv_facil_not_implemented 0x45/69 req_facil_not_imple_c 0D03 serv_facil_not_implemented 0x46/70 only_res_dig_bc_av_c 0A0C Digital_path_not_provided 0x4F/79 serv_opt_not_impl_c 0D03 serv_facil_not_implemented → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
INAP mapping
101/114
0x57/87 cd_user_not_in_CUG_c 0x58/88 incompat_dest_c 0x5A/90 non_existent_cug_c 0x5B/91 inv_tran_nw_sel_c 0x5F/95 inv_msg_unspec_c 0x61/97 msg_type_no_ex_imp_c 0x63/99 parm_no_ex_imp_dis_c 0x66/102 recovery_timer_exp_c 0x67/103 parm_no_ex_imp_pas_c 0x6E/110 parm_no_ex_dis_msg_c 0x6F/111 protocl_erro_unspec_c 0x7D/125in_service_discon_c 0x7E/126 in_charge_limit_exc_c 0x7F/127 interwork_unspecif_c Other external causes
→ → → → → → → → → → → → → → →
0213 n_user_not_in_cug 0C0B inconsist_between_a_and_b 0213 n_user_not_in_cug 0821 invalid_transit_n_select 0820 n_msg_content_error 0A02 trunk_circ_invalid_msg 0B2B param_no_exist_or_impl 0822 n_recovery_timer_expiry 0B2B param_no_exist_or_impl 0826 unrec_param_msg_discarded 0A04 trunk_circ_protocol_error 0B32 in_disconnected_by_scp 0016 cha_capa_of_subs_exceeded 0A03 interworking_failed 0015 normal_unspecified
NOTE 1 external cause diagnostics value was 0x1 (CCBS possible) 2 external cause diagnostics value was 0x2 (CCBS not possible)
Internal cause codes generated by INAP user part INTERNAL FAIL DESCRIPTIONS hex INTERNAL CAUSE error in SCF communication and trigger data FOP is 0x0000 normal end of call "continue" charging threshold given by the SCP has been reached 0x0016 subscriber's charging capacity exceeded in the exchange call is cleared, because of CUG check failed after Connect 0x0310 CUG call failure, operation was received from SCP unspecified time_out occurred in SCF-SRF communication 0x0317 overall time limit of inbased subscriber service no free circuits available 0x0401 interw unit congestion no free PBRU devices available 0x0404 pbru device congestion the service request received contains invalid data or 0x0405 erroneous request from request is received in wrong call phase co-process the response received contains invalid data 0x0407 erroneous answer from →
→
→
→
→ → →
→
© Nokia Siemens Networks
DN0124783, issue 5-0
102/114
INAP mapping
SCP asked the SSP to modify the called number and the max. is then exceeded The called number cannot be modified according to orders from the SCP. error in establishing charging during the call attempt to read a file failed a program block belonging to the system block has not been able to contact the partner program block call control fails to start the charging INAP protocol handler has detected an overload situation register analysis has been failed because of unknown addressing the internal call control analysis has failed the SCP has given a called party number that has no preanalysis. The SCP does not provide called party number when the analysis result is pure "make SCP enquiry". The service number is not in RZNTBL TGIFIL record is empty or wrong type. INAP protocol handler has detected a resource limitation OR there is no hand for a call congestion to SCP by INAP errorneous data from SCP in INAP operation that was received in TC-END unacceptable information received from the SCP and no repair instructions have been received no response from the SCP received within wait time
the limit for the amount of IDP operations from one BCSM is exceeded INAP protocol handler has detected an error in TCAP connection INAP protocol handler has encountered ASN.1 coding or decoding error overload management of IN services clears the call
the IN service causes clearing of the call
the user does not respond in time during the user interaction controlled by the SCP
© Nokia Siemens Networks
→
→ → →
→ → →
partner program block 0x0408 b-number length exceeded 0x0508 charging error 0x0509 file error 0x0603 no response from partnerprogram block 0x0608 setting of charging failed 0x060B overload congestion 0x0701 register analysis failed
→
0x0706 call interrupted during register analysis 0x070E configuration error
→
0x0719 no resource for call
→
→ →
→
→
→
→
→
→
→
→
0x080F circuit congestion 0x0B2B parameter does not exist or is not implemented 0x0B2C in application protocol error 0x0B2D intelligent network application response time-out 0x0B2E maximum number of triggering events in a call has been reached 0x0B2F tcap error 0x0B30 asn1 coding decoding error 0x0B31 selective call congestion has prevented call attempt 0x0B32 call release ordered intelligent network application 0x0C00 dial wait time exceeded
DN0124783, issue 5-0
INAP mapping
103/114
12.1.3
Calling party category mapping
OPERATIONS (from SCP to SSP)OPCODE Connect 20 OPERATIONS (from SSP to SCP)OPCODE InitialDP 00 EXTERNAL CATEGORY VALUES unknown_c 0x00/00 oper_fre_c 0x01/01 oper_eng_c 0x02/02 oper_ger_c 0x03/03 oper_rus_c 0x04/04 oper_spa_c 0x05/05 oper_nat_c 0x09/09 ordinary_c 0x0A/10 priority_c 0x0B/11 data_call_c 0x0C/12 test_call_c 0x0D/13 payphone_sf_c 0x0E/14 conf_call_sf_c 0x0F/15 alarm_dev_c 0x10/16 Mapping of the internal category to external category (from SSP to SCP) hex/ dec INTERNAL (CC) CATEGORY hex/ dec EXTERNAL CATEGORY 0x00/00 ordinary_1_c 0x0A/10 ordinary_c 0x01/01 ordinary_2_c 0x0A/10 ordinary_c 0x04/04 data_line_c 0x0C/12 data_call_c 0x05/05 pay_phone_c 0x0E/14 payphone_sf_c 0x08/08 priority_1_c 0x0B/11 priority_c 0x10/16 test_equipment_c 0x0D/13 test_call_c 0x11/17 operator_c 0x09/09 oper_nat_c 0x27/39 oper_fre_c 0x01/01 oper_fre_c 0x28/40 oper_eng_c 0x02/02 oper_eng_c 0x29/41 oper_ger_c 0x03/03 oper_ger_c 0x2A/42 oper_rus_c 0x04/04 oper_rus_c 0x2B/43 oper_spa_c 0x05/05 oper_spa_c 0x2F/47 conf_call_c 0x0F/15 conf_call_sf_c 0x30/48 alarm_call_c 0x10/16 alarm_dev_c 0x44/68 cc_pstn_c 0x0A/10 ordinary_c Other internal category 0x00/00 unknown_c → → → → → → → → → → → → → → → → →
Mapping of external category to internal category (from SCP to SSP) hex/ dec EXTERNAL CATEGORY hex/ dec CC CATEGORY →
© Nokia Siemens Networks
DN0124783, issue 5-0
INAP mapping
104/114
0x00/00 0x01/01 0x02/02 0x03/03 0x04/04 0x05/05 0x09/09 0x0A/10 0x0B/11 0x0C/12 0x0D/13 0x0E/14 0x0F/15 0x10/16
unknown_c oper_fre_c oper_eng_c oper_ger_c oper_rus_c oper_spa_c oper_nat_c ordinary_c priority_c data_call_c test_call_c payphone_sf_c conf_call_sf_c alarm_dev_c Other external category
© Nokia Siemens Networks
→ → → → → → → → → → → → → → →
0xFF/255 unknown_c 0x27/39 oper_fre_c 0x28/40 oper_eng_c 0x29/41 oper_ger_c 0x2A/42 oper_rus_c 0x2B/43 oper_spa_c 0x11/17 operator_c 0x00/00 ordinary_1_c 0x08/08 priority_1_c 0x04/04 data_line_c 0x10/16 test_equipment_c 0x05/05 pay_phone_c 0x2F/47 conf_call_c 0x30/48 alarm_call_c 0x00/00 ordinary_1_c
DN0124783, issue 5-0
CAMEL mapping
105/114
13 CAMEL mapping 13.1.1
Signalling
CAP User Part (CAMEL) CAP operations containing the cause parameter are listed below.
OPERATIONS (from SCP to SSP)OPCODE ReleaseCall 22 CallGap 41 OPERATIONS (from SSP to SCP)OPCODE InitialDP 0 EventReportBCSM 24 EXTERNAL CAUSE CODES NUMBER (Hex/Dec) un_alloc_num_c 0x01/01 no_route_to_spec_nw_c 0x02/02 no_route_to_dest_c 0x03/03 send_spec_inf_tone_c 0x04/04 misdial_trunk_pref_c 0x05/05 preemption_c 0x08/08 preemption_crct_res_c 0x09/09 in_service_fallback_code_1 0x0A/10 in_service_fallback_code_2 0x0B/11 in_service_fallback_code_3 0x0C/12 in_service_fallback_code_4 0x0D/13 normal_call_clear_c 0x10/16 user_busy_c 0x11/17 no_user_responding_c 0x12/18 no_answer_fr_user_c 0x13/19 absent_subscriber_c 0x14/20 call_rejected_c 0x15/21 number_changed_c 0x16/22 dest_out_of_ord_c 0x1B/27 address_incomplete_c 0x1C/28 facility_rejected_c 0x1D/29 normal_unspecified_c 0x1F/31 no_circuit_avail_c 0x22/34 network_out_of_ord_c 0x26/38 temporary_failure_c 0x29/41 switching_eq_cong_c 0x2A/42 access_inf_disc_c 0x2B/43
© Nokia Siemens Networks
DN0124783, issue 5-0
CAMEL mapping
106/114
req_chan_not_avail_c precedence_call_bl_c res_unavail_unspec_c req_facil_not_subsc_c out_calls_barr_w_CUG_c in_calls_barr_w_CUG_c bear_cap_not_author_c bear_cap_no_pres_av_c incon_in_out_access_inf_c serv_not_av_unspec_c bear_cap_not_implem_c req_facil_not_imple_c only_res_dig_bc_av_c serv_opt_not_impl_c cd_user_not_in_CUG_c incompat_dest_c non_existent_cug_c inv_tran_nw_sel_c inv_msg_unspec_c msg_type_no_ex_imp_c parm_no_ex_imp_dis_c recovery_timer_exp_c parm_no_ex_imp_pas_c parm_no_ex_dis_msg_c protocl_erro_unspec_c in_service_discon_c in_charge_limit_exc_c interwork_unspecif_c
13.1.2 hex 0000 0005 0006 0010 0012 0013 0021 0022 0201 0202 0205
0x2C/44 0x2E/46 0x2F/47 0x32/50 0x35/53 0x37/55 0x39/57 0x3A/58 0x3E/62 0x3F/63 0x41/65 0x45/69 0x46/70 0x4F/79 0x57/87 0x58/88 0x5A/90 0x5B/91 0x5F/95 0x61/97 0x63/99 0x66/102 0x67/103 0x6E/110 0x6F/111 0x7D/125 0x7E/126 0x7F/127
Mapping table
Reason for mapping internal to external (from SSP to SCP) INTERNAL CLEAR CODE hex/ dec EXTERNAL CAUSE CODE Normal_end_of_the_call 0x10/16 normal_call_clear_c B_subscriber_busy 0x11/17 user_busy_c B_answer_time_out 0x13/19 no_answer_fr_user_c Absent_subscriber 0x14/20 absent_subscriber_c No_paging_response 0x12/18 no_user_responding_c Ct_recall_time_out 0x13/19 no_answer_fr_user_c B_busy_ccbs_possible 0x11/17 user_busy_c(Note 1) B_busy_ccbs_not_possible 0x11/17 user_busy_c(Note 2) Call_released 0x15/21 call_rejected_c Clear_request_rec_out_crct 0x10/16 normal_call_clear_c Radio_if_congestion 0x22/34 no_circuit_avail_c
© Nokia Siemens Networks
→ → → → → → → → → → → →
DN0124783, issue 5-0
107/114
0206 Call_rejected 0207 Subscriber_congestion 0212 N_unknown_dialling 0213 N_user_not_in_cug 0300 Restrict_in_out_direction 0304 B_line_out_of_service 0305 B_line_faulty 0306 B_calls_restricted 0307 B_number_unused 0308 B_number_changed 030A cl_a_onhook_set_up_phase 030B cl_a_onhook_answer_phase 030E b_line_blocked 0310 Cug_reject 0311 Bearer_serv_not_prov 0312 Tele_serv_not_prov 0313 Illegal_subscriber 0314 Unidentified_subscriber 0315 Call_diversion_barring 0316 Memory_capacity_exceeded 0317 In_service_time_exceeded 0319 Illegal_subscriber_station 031A cug_rec_icb 031C cug_rej_not_member 031D cug_rej_ocb 031F cug_rej_bs_violation 0320 Cug_rej_ss_violation 0401 interw_unit_congestion 0402 Regist_total_time_exceeded 0403 Mfcu_congestion 0404 Pbru_congestion 0406 Connect_failed_in_gsw_swi 0407 Err_answer_from_co_process 0408 B_number_overflow 040A traffic_type_congestion 040D unallocated_roaming_number 040E roaming_not_allowed 0508 Charging_error 0509 File_error 050C mfc_ass_chan_close_missed 0600 File_record_congestion 0603 No_response_from_co_proces 0606 Conferen_device_congestion 0608 Charging_not_started 060B overload_congestion © Nokia Siemens Networks
CAMEL mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x15/21 call_rejected_c 0x2f/47 res_unavail_unspec_c 0x1c/28 address_incomplete_c 0x57/87 cd_user_not_in_CUG_c 0x58/88 incompat_dest_c 0x1b/27 dest_out_of_ord_c 0x12/18 no_user_responding_c 0x58/88 incompat_dest_c 0x01/01 un_alloc_num_c 0x16/22 number_changed_c 0x10/16 normal_call_clear_c 0x10/16 normal_call_clear_c 0x12/18 no_user_responding_c 0x37/55 in_calls_barr_w_CUG_c 0x39/57 bear_cap_not_author_c 0x3f/63 serv_not_av_unspec_c 0x01/01 un_alloc_num_c 0x01/01 un_alloc_num_c 0x15/21 call_rejected_c 0x2f/47 res_unavail_unspec_c 0x66/102recovery_timer_exp_c 0x58/88 incompat_dest_c 0x37/55 in_calls_barr_w_CUG_c 0x57/87 cd_user_not_in_CUG_c 0x35/53 out_calls_bar_w_CUG_c 0x1d/29 facility_rejected_c 0x3e/62 incon_in_out_access_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x2a/42 switching_eq_conq_c DN0124783, issue 5-0
108/114
060E unit_restarted 0610 Ec_failure 0701 Register_analysis_failed 0706 Call_interrupt_in_reg_ana 070A forced_clear_of_a_call 070B modem_error 070D announcement_error 070E configuration_error 070F diu_pool_error 0719 No_resource_for_call 0804 Outgoing_circ_congestion 0807 R2_signal_pause_time_out 0808 R2_sign_backwards_time_out 0809 R2_err_signl_from_out_crct 080A r2_err_signal_from_in_crct 080D out_circuit_out_of_order 080E in_circuit_out_of_order 080F circuit_congestion 0810 Facility_not_supported 0811 Network_failure 0812 Map_failure 0813 Switching_equ_congestion 0814 Circuit_group_congestion 0815 B_access_barred 0816 Congestion_send_info_tone 0817 N_unallocated_number 0818 N_line_out_of_service 0819 N_subscriber_nbr_changed 081A terminal_congestion 081B no_hlr_response 081C no_vlr_response 081F n_overload_congestion 0820 N_msg_content_error 0821 Invalid_transit_n_select 0822 N_recovery_timer_expiry 0824 Pcm_faulty 0826 Unrec_param_msg_discarded 0900 No_mf_forward_signal 090D seizu_ack_time_out_in_crct 0A02 trunk_circ_invalid_msg 0A03 interworking_failed 0A04 trunk_circ_protocol_error 0A05 crct_released_by_co_exc 0A08 destinat_sign_out_of_order 0A09 address_complete_time_out © Nokia Siemens Networks
CAMEL mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x29/41 temporary_failure_c 0x22/34 no_circuit_avail_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x22/34 no_circuit_avail_c 0x1d/29 facility_rejected_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x2a/42 switching_eq_conq_c 0x22/34 no_circuit_avail_c 0x58/88 incompat_dest_c 0x04/04 send_spec_inf_tone_c 0x01/01 un_alloc_num_c 0x1b/27 dest_out_of_ord_c 0x16/22 number_changed_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2f/47 res_unavail_unspec_c 0x2a/42 switching_eq_conq_c 0x5f/95 inv_msg_unspec_c 0x5b/91 inv_tran_nw_sel_c 0x66/102recovery_timer_exp_c 0x2f/47 res_unavail_unspec_c 0x6e/110parm_no_ex_dis_msg_c 0x7f/127 interwork_unspecif_c 0x7f/127 interwork_unspecif_c 0x61/97 msg_type_no_ex_imp_c 0x7f/127 interwork_unspecif_c 0x6f/111 protocl_erro_unspec_c 0x26/38 network_out_of_ord_c 0x1b/27 dest_out_of_ord_c 0x01/01 un_alloc_num_c DN0124783, issue 5-0
109/114
0A0C Digital_path_not_provided 0A0D no_route_to_destination 0B10 v110_frame_sync_fail 0B11 modem_communication_error 0B12 rlp_or_ms_frame_sync_error 0B13 radio_if_failure 0B14 handover_failure 0B15 ciphering_not_succeeded 0B16 remote_equipment_failure 0B17 adress_incomplete 0B18 service_unavailable 0B19 service_incompatible 0B1A bssmap_protocol_error 0B1B radio_if_msg_failure 0B1C radio_if_fail_rev_to_old 0B20 nae_error 0B21 dte_uncontrolled 0B23 dual_seizure_both_way_crct 0B2A blocking_received 0B2B param_no_exist_or_impl 0B2C in_protocol_error 0B2D in_appl_response_time_out 0B2F in_tcap_error 0B30 asn1_codec_error 0B3E call_period_timeout 0C00 dial_wait_time_exceeded 0C01 prohibited_dialling 0C02 insufficient_dialling 0C09 serv_facil_activa_restrict 0C0A serv_facil_usage_restrict 0C0B inconsist_between_a_and_b 0C0D bc_not_presently_available 0D00 subs_signa_msg_content_err 0D01 subs_signa_msg_format_err 0D03 serv_facil_not_implemented 0D04 subs_sig_protocol_error 0D06 aocc_charging_error 0D07 no_user_responding 0D08 gsm_erh408_prot_timer_exp 0D0D msg_not_cmptbl_or_impl Other internal causes
CAMEL mapping → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
0x46/70 only_res_dig_bc_av_c 0x03/03 no_route_to_dest_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x1c/28 address_incomplete_c 0x3f/63 serv_not_av_unspec_c 0x58/88 incompat_dest_c 0x6f/111 protocl_erro_unspec_c 0x6f/111 protocl_erro_unspec_c 0x29/41 temporary_failure_c 0x01/01 un_alloc_num_c 0x3f/63 serv_not_av_unspec_c 0x29/41 temporary_failure_c 0x29/41 temporary_failure_c 0x63/99 parm_no_ex_imp_dis_c 0x6f/111 protocl_erro_unspec_c 0x66/102recovery_timer_exp_c 0x6f/111 protocl_erro_unspec_c 0x6f/111 protocl_erro_unspec_c 0x66/102recovery_timer_exp_c 0x1c/28 address_incomplete_c 0x01/01 un_alloc_num_c 0x01/01 un_alloc_num_c 0x39/57 bear_cap_not_author_c 0x3f/63 serv_not_av_unspec_c 0x58/88 incompat_dest_c 0x3a/58 bear_cap_no_pres_av_c 0x6f/111 protocl_erro_unspec_c 0x6f/111 protocl_erro_unspec_c 0x41/65 bear_cap_not_implem_c 0x6f/111 protocl_erro_unspec_c 0x29/41 temporary_failure_c 0x12/18 no_user_responding_c 0x66/102recovery_timer_exp_c 0x61/97 msg_type_no_ex_imp_c 0x1F/31 normal_unspecified_c
NOTE
© Nokia Siemens Networks
DN0124783, issue 5-0
CAMEL mapping
110/114
1 cause diagnostics value is set to 0x1 (CCBS possible), not supported with Camel Phase 1 and 2 2 cause diagnostics value is set to 0x2 (CCBS not possible), not supported with Camel Phase 1 and 2
Reason for mapping external to internal (from SCP to SSP) hex/dec EXTERNAL CAUSE CODE hex INTERNAL CLEAR CODE 0x01/01 un_alloc_num_c 0817 n_unallocated_number 0x02/02 no_route_to_spec_nw_c 0A0D no_route_to_spec_nw 0x03/03 no_route_to_dest_c 0A0D no_route_to_destination 0x04/04 send_spec_inf_tone_c 0816 congestion_send_info_tone 0x05/05 misdial_trunk_pref_c 0817 n_unallocated_number 0x08/08 preemption_c 0015 normal_unspecified 0x09/09 preemption_circuit_res_c 0015 normal_unspecified 0x0A/10 in_service_fallback_code_1 0B38 in_service_fallback_code_1 0x0B/11 in_service_fallback_code_2 0B39 in_service_fallback_code_2 0x0C/12 in_service_fallback_code_3 0B3A in_service_fallback_code_3 0x0D/13 in_service_fallback_code_4 0B3C in_service_fallback_code_4 0x10/16 normal_call_clear_c 0000 normal_end_of_the_call 0x11/17 user_busy_c 0005 b_subscriber_busy 0x11/17 user_busy_c 0021 b_busy_ccbs_possible(Note 1) 0x11/17 user_busy_c 0022 b_busy_ccbs_not_possible(Note 2) 0x12/18 no_user_responding_c 0D07 no_user_responding 0x13/19 no_answer_fr_user_c 0006 b_answer_time_out 0x14/20 absent_subscriber_c 0010 absent_subscriber 0x15/21 call_rejected_c 0206 call_rejected 0x16/22 number_changed_c 0819 n_subscriber_nbr_changed 0x1B/27 dest_out_of_ord_c 0818 n_line_out_of_service 0x1C/28 address_incomplete_c 0B17 address_incomplete 0x1D/29 facility_rejected_c 0810 facility_not_supported 0x1F/31 normal_unspecified_c 0015 normal_unspecified 0x22/34 no_circuit_avail_c 080F circuit_congestion 0x26/38 network_out_of_ord_c 0A05 crct_released_by_co_exc 0x29/41 temporary_failure_c 0811 network_failure 0x2A/42 switching_eq_cong_c 0813 switching_equ_congestion 0x2B/43 access_inf_disc_c 0015 normal_unspecified 0x2C/44 req_chan_not_avail_c 080F circuit_congestion 0x2E/46 precedence_call_bl_c 0811 network_failure 0x2F/47 res_unavail_unspec_c 080F circuit_congestion → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0
CAMEL mapping
111/114
0x32/50 req_facil_not_subsc_c 0x35/53 out_calls_barr_w_CUG_c 0x37/55 in_calls_barr_w_CUG_c 0x39/57 bear_cap_not_author_c 0x3A/58 bear_cap_no_pres_av_c 0x3E/62 incon_in_out_access_inf_c 0x3F/63 serv_not_av_unspec_c 0x41/65 bear_cap_not_implem_c 0x45/69 req_facil_not_imple_c 0x46/70 only_res_dig_bc_av_c 0x4F/79 serv_opt_not_impl_c 0x57/87 cd_user_not_in_CUG_c 0x58/88 incompat_dest_c 0x5A/90 non_existent_cug_c 0x5B/91 inv_tran_nw_sel_c 0x5F/95 inv_msg_unspec_c 0x61/97 msg_type_no_ex_imp_c 0x63/99 parm_no_ex_imp_dis_c 0x66/102 recovery_timer_exp_c 0x67/103 parm_no_ex_imp_pas_c 0x6E/110 parm_no_ex_dis_msg_c 0x6F/111 protocl_erro_unspec_c 0x7D/125in_service_discon_c 0x7E/126 in_charge_limit_exc_c 0x7F/127 interwork_unspecif_c Other external causes
→ → → → → → → → → → → → → → → → → → → → → → → → → →
0C09 serv_facil_activa_restrict 031D cug_rej_ocb 0310 cug_reject 0C09 serv_facil_activa_restrict 0C0D bc_not_presently_available 0320 cug_rej_ss_violation 0C0A serv_facil_usage_restrict 0D03 serv_facil_not_implemented 0D03 serv_facil_not_implemented 0A0C Digital_path_not_provided 0D03 serv_facil_not_implemented 0213 n_user_not_in_cug 0C0B inconsist_between_a_and_b 0213 n_user_not_in_cug 0821 invalid_transit_n_select 0820 n_msg_content_error 0A02 trunk_circ_invalid_msg 0B2B param_no_exist_or_impl 0822 n_recovery_timer_expiry 0B2B param_no_exist_or_impl 0826 unrec_param_msg_discarded 0A04 trunk_circ_protocol_error 0B32 in_disconnected_by_scp 0016 cha_capa_of_subs_exceeded 0A03 interworking_failed 0015 normal_unspecified
NOTE 1 external cause diagnostics value was 0x1 (CCBS possible), not supported with Camel Phase 1 and 2 2 external cause diagnostics value was 0x2 (CCBS not possible), not supported with Camel Phase 1 and 2
Internal cause codes generated by INAP user part INTERNAL FAIL DESCRIPTIONS hex INTERNAL CAUSE error in SCF communication and trigger data FOP is 0x0000 normal end of call →
© Nokia Siemens Networks
DN0124783, issue 5-0
112/114
CAMEL mapping
"continue" call is cleared, because of CUG check failed after Connect operation was received from SCP time_out occurred in SCF-SRF communication
no free circuits available no free PBRU devices available the service request received contains invalid data or request is received in wrong call phase the response received contains invalid data SCP asked the SSP to modify the called number and the max. is then exceeded The called number cannot be modified according to orders from the SCP. error in establishing charging during the call attempt to read a file failed a program block belonging to the system block has not been able to contact the partner program block call control fails to start the charging CAP protocol handler has detected an overload situation register analysis has been failed because of unknown addressing the internal call control analysis has failed the SCP has given a called party number that has no preanalysis. The SCP does not provide called party number when the analysis result is pure "make SCP enquiry". The service number is not in RZNTBL TGIFIL record is empty or wrong type. CAP protocol handler has detected a resource limitation OR there is no hand for a call congestion to SCP by CAP errorneous data from SCP in CAP operation that was received in TC-END unacceptable information received from the SCP and no repair instructions have been received no response from the SCP received within wait time
the limit for the amount of IDP operations from one BCSM is exceeded CAP protocol handler has detected an error in TCAP connection CAP protocol handler has encountered ASN.1 coding or © Nokia Siemens Networks
→
→
→ → →
→
→
→ → →
→ → →
0x0310 CUG call failure, unspecified 0x0317 overall time limit of inbased subscriber service 0x0401 interw unit congestion 0x0404 pbru device congestion 0x0405 erroneous request from co-process 0x0407 erroneous answer from partner program block 0x0408 b-number length exceeded 0x0508 charging error 0x0509 file error 0x0603 no response from partnerprogram block 0x0608 setting of charging failed 0x060B overload congestion 0x0701 register analysis failed
→
0x0706 call interrupted during register analysis 0x070E configuration error
→
0x0719 no resource for call
→
→
0x080F circuit congestion 0x0B2B parameter does not exist or is not implemented 0x0B2C in application protocol error 0x0B2D intelligent network application response time-out 0x0B2E maximum number of triggering events in a call has been reached 0x0B2F tcap error
→
0x0B30 asn1 coding decoding
→ →
→
→
→
DN0124783, issue 5-0
CAMEL mapping
113/114
decoding error overload management of IN services clears the call
→
the IN service causes clearing of the call
→
No answer from SCP to CAMEL Call Period report (ACR) the user does not respond in time during the user interaction controlled by the SCP
13.1.3
→ →
error 0x0B31 selective call congestion has prevented call attempt 0x0B32 call release ordered intelligent network application 0x0B3E call period timeout 0x0C00 dial wait time exceeded
Calling party category mapping
OPERATIONS (from SCP to SSP)OPCODE Connect 20 OPERATIONS (from SSP to SCP)OPCODE InitialDP 00 EXTERNAL CATEGORY VALUES unknown_c 0x00/00 oper_fre_c 0x01/01 oper_eng_c 0x02/02 oper_ger_c 0x03/03 oper_rus_c 0x04/04 oper_spa_c 0x05/05 oper_nat_c 0x09/09 ordinary_c 0x0A/10 priority_c 0x0B/11 data_call_c 0x0C/12 test_call_c 0x0D/13 payphone_sf_c 0x0E/14 payphone_c 0x0F/15 alarm_dev_c 0x10/16 Mapping of the internal category to external category (from SSP to SCP) hex/ dec INTERNAL (CC) CATEGORY hex/ dec EXTERNAL CATEGORY 0x00/00 ordinary_1_c 0x0A/10 ordinary_c 0x01/01 ordinary_2_c 0xE0/224 payphone_t_2_c 0x04/04 data_line_c 0x0C/12 data_call_c 0x05/05 pay_phone_c 0x0F/15 payphone_c 0x08/08 priority_1_c 0x0B/11 priority_c 0x10/16 test_equipment_c 0x0D/13 test_call_c 0x11/17 operator_c 0x09/09 oper_nat_c 0x27/39 oper_fre_c 0x01/01 oper_fre_c → → → → → → → → →
© Nokia Siemens Networks
DN0124783, issue 5-0