MOSHELL COMMANDS
NOTE: Exclusive for PENTA PROJECT TEAM/Author/RMALVAREZ 1. To read MCPA temp Cabx (to check RBS status) Ø lhsh 010200/port_0_dev_13 mcpaBoard temp Ø lhsh 010200/port_0_dev_13 help Ø lhsh 010200/port_0_dev_13 restart (if need to restart) Ø TELNET commands should MOSHELL hang due to GPB telnet IP add cv cu cv ls cv mk cv set restartObj me
2. To check E1-MS port in RXI/RBS (add E1 for RBS) In RNC st
Ø get iub - à look for RBS ID Ø In RXI pr . eg. pr .0095 Ø lk Ø st atmport=ms-x-y Ø bl Ø lget ms-2-2 (then check iub number with STR printout – see tally or not) Ø reservedBy Aal2PathVccTp=b0001a2 <----- iub # = Ø 0001 to deblock E1 port in RXI Ø lst slot=12.*31 Ø lst Slot=16.*Vc12Ttp=14 Ø ldeb Slot=16.*Vc12Ttp=14 - (Example MS-16-14) Ø In RBS (when port is ready but E1 not pull through yet – so that no alarm) pr atmport get ie. get 1345 Ø lget Subrack=1,Slot=2,PlugInUnit=1,Etm1=1,E1PhysPathTerm=pp2 Ø set administrativeState 0 (to lock the 2 nd physical port) Ø set 194 administrativeState 0 (to lock the 2 nd physical port) Ø Ø
3. To check pm (performance) counters in RNC/RXI get 1 (to see the performance directory) Ø ls -l /p001200/pm/ | grep xml (to see the performance files) Ø pst (list the scanners, status) Ø pmr [-m 5 –p 3] (get performance report) [for the last 5 hours Ø + 3 ] 4. To create performance counters scanner pst Ø pgetsn Ø pcr eg. pcr cellcarrier Ø pmAverageRssi pget to read the counters Ø
PDF created with pdfFactory trial version www.pdffactory.com
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Ø Ø
pbl/pdeb pdel
to stop/resume scanner to delete scanner
5. To set Electrical Tilt (RET) pr retdevice Ø get Ø set electricalAntennaTilt Ø get ret electrical Ø 6. To set Latitude/Longitude get sector lat Ø set sector latitude Ø 7.
To log alarm in a nice format lgevsm Ø
8.
Sample Scripts in moshell for 10 Ø Enter commmands (one per line), then type "done" > get radiolink num > wait 2 > done
9. To enable E1 supervision set Ø 10. To create Group (eg. Not reserved VclTp) get vcltp reservedby !.*= Ø lma vcltp reservedby !.*= Ø 11. To create performance counters pst Ø
12. To check cell state In RBS lst cell Ø get radiolinks (to see how many line/s being used) Ø 13. To check RBS MO In RBS st plug Ø cabx Ø cab Ø
(AuxPlugInUnit=2 is the RET, (without the external parts)
14. To change SAC (Service Area Code) In RBS determine max capability to transmit
AuxPlugInUnit=1 is the ASC)
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
15. To lock/unlock cells In RNC st utrancell=sunwmu Ø lst sunw Ø lbl sunw (to lock cell & channels) Ø bl sunw (to lock cell only) Ø deb sunw (to unlock) Ø 16. To check RBS info In RBS Get 0 Ø Get 1 (check ntpServerAddressPrimary) Ø 17. To check network clock synchronisation In RNC & RBS Read clock (GMT +8) Ø ntpconfig info Ø Check which OMNIFSERVER the node is connected to (i.e Ø ntpServerAddressPrimary) – from get 1 18. To check atmport & pp (physical port) In RBS lpr atmport Ø vc32&33 for signaling Ø lpget 1007 (vc proxy) – to see number of ATM traffic cells transferred Ø get atmport=1-2-2 Ø then : lget Subrack=1,Slot=2,PlugInUnit=1,Etm1=1,E1PhysPathTerm=pp2 Ø to un/lock have to set values 1 or 0 Ø 19. To administer state of Mos In RBS St plug Ø Deb proxy Ø Bl proxy Ø No need to use set 1 or set 0 (only for physical ports) otherwise use deb & Ø bl 20. To autocreateCV In RNC & RBS Get config Ø Cv ls (2 CVs will be used for the autocreate CV function) Ø Set “proxy” autoCreatedCVIsTurnedOn true/false Ø Set timeForAutoCreatedCV (UTC time) Ø Set timeForAutoCreatedCV 13:00 (cv autocreated at 9pm) Ø 21. To restart Node In RNC,RXI & RBS acc 0 restart Ø poll (to wait 20seconds until node comes up again) Ø 22. To create CV
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
23. To restart node In RNC & node B acc 0 restart Ø pol - to get moshell connected once node has restarted Ø 24. To check plugin status In RNC & node B st plugin Ø st plugin 1 0 Ø st plugin 0 1 Ø lst plug 0 Ø 25. To enter Moshell with security enabled In RNC & node B moshell -c host.p12 10.78.37.225 Ø 26. To block sectors via Moshell In RNC St blip Ø Bl the proxy Ø Deb the proxy (can have multiple proxies for more cells) Ø 27. To view delay & attenuation parameters within a sector In RBS Get jumper Ø Get feeder Ø Get rbs xdl Ø 28. To delete something already done with a script In RNC/RXI/RBS First you have to generate the MO Delete script Ø This is done by ./undomo add2nde1inrxi_PUJMMU.mo > pujmrxibesi01.mo Ø [~]$ ./undomo add2nde1inrxi_PUJMMU.mo > pujmrxibesi01.mo Ø [~]$ Ø Where add2nde1inrxi_PUJMMU.mo is the script which was run earlier Ø And pujmrxibesi01.mo is the Delete Script Ø Modify add2nde1inrxi_PUJMMU.mo so that downtime will be less Ø Run pujmrxibesi01.mo to undo the wrongly defined MO Ø Then run the modified/correct add2nde1inrxi_PUJMMU.mo Ø 29. To check E1 state In RBS St atmport Ø Check port lock state Ø St pp St pp2 Ø
30. To check locked board in node In all nodes
st pp3
st pp4
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Ø
Acc 001400 reload
32. run and trun In all nodes trun is only for xml scripts Ø run for scripts such as set DAGAMU_1 usedFreqThresh2dEcno -12 Ø trun for running the last script : rbs_EQINMU_site_complete.mo Ø run is for any script (txt for example) Ø open logfile l+ 20060113_CR003_RNCTGEM01.log Ø cannot have undo mode while having gsg activated Ø run CR003_13012006.txt Ø close logfile Ø 33. CAB printout 0 = slot 28, 1 = slot 1 In all nodes RXIKPNG02> cab 060206-11:09:22 ....... ================================================================================== =================== SMN APN BOARD GREEN YELLOW RED PRODUCT NR REV DATE SERIAL NR TEMP COREMGR ================================================================================== =================== 0 1 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20050608 TU86364489 0 2 HUB MP ON OFF OFF ROJ 119 2106/40 R5A 20050626 TU86494707 +32C Active 0 3 GPB40 ON OFF OFF ROJ 119 2106/40 R5A 20050626 TU86494699 +31C StandbyReady 0 4 TUB ON OFF OFF ROJ 119 2104/4 R3B 20050620 TU86442436 0 5 TUB ON OFF OFF ROJ 119 2104/4 R3B 20050620 TU86442439 0 8 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644146 0 10 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644042 0 12 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644052 0 14 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644056 0 16 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644037 0 18 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644067 0 20 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050708 TU86592867 0 24 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86545997 0 25 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86545998 0 26 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86545996 0 27 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86546001 0 0 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20050608
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
34. When lock/unlock from log In RBS Lgv Ø Lgaevsm – rather long Ø 35. Read VSWR / OUTPUT Power from RBS In RBS lhsh 010900 ps port* Ø lhsh 010600 lhsh port_0_dev_17 asc vswr Ø lhsh 010900 lhsh port_0_dev_19 asc vswr Ø lhsh 010900 lhsh port_0_dev_19 asc vswr Ø lhsh 010600 lhsh port_0_dev_17 asc pow Ø acc 011200 restart - restart AIU Ø Ø Ø Ø Ø Ø Ø Ø Ø
Ø Ø Ø Ø Ø Ø
- sector 1 - sector 2
port_0_dev_5 FU12 port_1_dev_11 ASC Sec.2-port_4_dev_6 RU21 port_4_dev_6 FU12 port_5_dev_13 ASC Sec.3-port_8_dev_7 RU21 port_8_dev_7 FU12 port_9_dev_15 ASC SMN APN PORT BOARD GREEN YELLOW RED PRODUCT NR REV DATE SERIAL NR ============================================================================ ===================================== 0 12 port_0_dev_4 RU22 steady 16hz off KRC 118 22/1 R1G 20070829 AE55520905 0 12 port_4_dev_5 RU22 steady 16hz off KRC 118 22/1 R1G 20070829 AE55520893 0 12 port_8_dev_6 RU22 steady 16hz off KRC 118 22/1 R1G 20070829 AE55520921 ----------------------------------------------------------------------------------------------------------------
Ø Ø Ø Ø
080408-13:32:58 10.109.246.153 7.0h RBS_NODE_MODEL_J_5_16 stopfile=/tmp/1052 $ lhsh 001200/port_0_dev_4 fui get devstat Board: fuHw: Hw08P1, faultStatus: 0x0, temp: temp: 47.0, sv: on, svTmaDegrad: off, comp: on
Ø Ø Ø Ø Ø Ø Ø Ø Ø
Dev1: mode: {ModeAuxTma}, feedPow: highPow capability: {vswrAntSv | tma19Sv | ulGainConf | maxUlGain} svCtrl: 0xe400, faultStatus: 0x0000 txFreq: 882800, sensitivity: 49, gainUl: 4.0, volt: 16571.5, curr: 84.0, dCycle: 0.0 Dev2: mode: {ModeAuxTma}, feedPow: highPow capability: {resAntSv | tma19Sv | ulGainConf | maxUlGain} svCtrl: 0x2400, faultStatus: 0x0000 txFreq: 0, sensitivity: 0, gainUl: 4.0, volt: 16565.9, curr: 90.4, dCycle: 0.0
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
USMLAP30> lhsh 001200/port_0_dev_4 fui get vswr 080521-03:27:34 10.108.243.9 7.0t RBS_NODE_MODEL_J_5_16 stopfile=/tmp/5952 $ lhsh 001200/port_0_dev_4 fui get vswr vswr: 24.3[dB] <<<< result USMLAP30> lhsh 001200/port_8_dev_6 fui get vswr 080521-03:28:17 10.108.243.9 7.0t RBS_NODE_MODEL_J_5_16 stopfile=/tmp/5952 $ lhsh 001200/port_8_dev_6 fui get vswr vswr: 24.9[dB] <<<< result
36. maxDlPowerCapability /maxDl In RBS get local xdl Ø In RBS get SOGXBU_1 maximumtransmissionpower Ø 37. redefine TD in VC In RBS Resources for CELL does not come up – apparently TD is defined as U42 Ø lget AtmPort=MS-1-2-1,VplTp=vp1,VpcTp=1,VclTp=vc39 Ø lrset AtmPort=MS-1-2-1,VplTp=vp1,VpcTp=1,VclTp=vc39 atmTrafficDescriptorId Ø AtmTrafficDescriptor=C2P4000 pr. Bq - must be win30 Ø pr aal2 Ø then get proxy for TransportNetwork=1,Aal2PathVccTp=ba1 Ø then lpr AtmPort=1-2-1,VplTp=vp1,VpcTp=1,VclTp=vc39 Ø get the proxy Ø look for AtmTrafficDescriptor=C2P4000 Ø 38. Check E1 loop In node lacc AtmPort=MS-27-1,VplTp=vp5 eteloopback Ø 39. RBSID In node RBS Pr iub Ø
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
41. Change ARFCN freq at RNC & RBS ARFCN 10637 DL Freq (MHz) 2127.4 UL Freq (MHz) 1937.4 In node RNC get allmmu_1 arf Ø typical values (uarfcnDl 10662 & uarfcnUl 9712 ) Ø In node RBS get antenna fq Ø typical values (fqBandHighEdge 10712 & fqBandLowEdge 10612) Ø thus if requested value at RNC is 10637 and if the value is between 10612 & Ø 10712 at RBS, change only at RNC
42. To look for host.p12 in Node B In node RBS Ls will show you are in drive D Ø To go to C drive: cd /c Ø Go to java folder Ø Ls and you will Ø ftp 10.78..... 10.78..... Ø Pw – rbs rbs Ø Bin (make sure in Binary and not ASCII) Ø Cd /c Ø Cd java Ø Put host.p12 (ensure host.p12 file in moshell folder ya) Ø 43. To continuously ping Ping –s 10.78.1.1101 44. To check IP connectivity In node RNC,RXI,ATMCC,RBS lacc AtmPort=1-2-1 eteloopback Ø CREATE ( parent "ManagedElement=1,TransportNetwork=1,AtmPort=MS-27-1,VplTp=vp1,VpcTp=1" identity "vc12232" moType VclTp exception none nrOfAttributes 3
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
45. To check queueSelectAlgorithm & cqiAdjustmentOn at RBS In node RBS UEFAMU> pr carrier que Ø Ø Ø Ø Ø Ø Ø Ø Ø
060615-14:50:24 10.78.71.129 6.1zc RBS_NODE_MODEL_H_6_2 ============================================================================ ======= Proxy MO ============================================================================ ======= 1381 NodeBFunction=1,Sector=3,Carrier=1 1399 NodeBFunction=1,Sector=2,Carrier=1 1417 NodeBFunction=1,Sector=1,Carrier=1
Ø Ø Ø
set 1417 queueSelectAlgorithm 0
UEFAMU> get 1417 que 060615-14:51:08 10.78.71.129 6.1zc RBS_NODE_MODEL_H_6_2 ============================================================================== MO Attribute Value ============================================================================== Sector=1,Carrier=1 frequencyPlane 1 Sector=1,Carrier=1 queueSelectAlgorithm 1 (PROPORTIONAL_FAIR) ============================================================================== Total: 1 MOs UEFAMU> set 1417 queueSelectAlgorithm 0 060615-14:51:24 10.78.71.129 6.1zc RBS_NODE_MODEL_H_6_2 Set queueselectalgorithm on following MOs ? =================================================================================== 1417 NodeBFunction=1,Sector=1,Carrier=1 =================================================================================== Are you Sure [y/n] ? y ============================================================================== Id MO queueselectalgorithm Result ============================================================================== 1417 Sector=1,Carrier=1 0 >>> Set. ============================================================================== Total: 1 MOs attempted, 1 MOs set UEFAMU> get 1417 que
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
47. To check RBS ID in RBS In node RBS Get IUB Ø 48. To check antenna Supervision Threshold In node RBS get antenna antennaSupervisionThreshold Ø 49. To check downlink & uplink range In node RBS lget antenna low|high Ø The downlink – uplink = 190x5=950 Ø
50. To check commands executed within a node In node Lgo 1 Ø 1 for number of days Ø 51. To add software allocations in the RBS for ETMC1 In node RBS Open EMAS Ø Go to SoftwareAllocation Ø Right click, Add Ø Choose the specific board/ swallocation Ø - fact is it will create a SWallocation ID = 1 in the rbs Ø Use moshell to create an Undo file Ø U+ Ø Then delete the swallocation Ø Lt swalloc Ø Pr swalloc Ø Del proxy Ø UØ Then edit the undo file Ø 52. To enable trace In node RBS te enable bus_send bus_receive NBAP* Ø te s Ans* (just to look at the last line) Ø te enable bus_send bus_receive Ans_aal2ap_proc Ø
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Trusted by over 1 million members
Try Scribd FREE for 30 days to access over 125 million titles without ads or interruptions! Start Free Trial Cancel Anytime.
Ø Ø Ø Ø Ø Ø Ø Ø
$ te status NBAP pid name enabled groups - NBAP check error info bus_send bus_receive interface object To disable ---à te disable bus_send bus_receive NBAP Check status again $ te status NBAP pid name enabled groups - NBAP check error info interface object
In node TeraTerm User = eric Ø Pw = ericsson Ø Monitor 10.78.xx.xx Ø 54. To check commands sent in node In node RNC, RBS, RXI hi Ø 55. To check external Open Door alarm in RBS is set to which probable cause In node RBS Pr almdevice Ø Get proxy (either 2 / 1 or 9) Ø Usually 9 for RBS door and 2 for BBU door Ø Some put 1 for BBU door Ø Get proxy for parameter check Ø Lock proxy to change probableCause Ø Bl 54 Ø probableCause 522 à power supply Ø probableCause 118 à enclosure_door_open_m3100 Ø set 54 probableCause 118 Ø then unlock back proxy Ø deb 54 Ø 56. To calibrate RET via moshell In node RBS Lpr ret Ø Acl proxy Ø 253 Ø Equipment=1,SectorAntenna=3,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1 ,RetDevice=1 acc 267 forceCalibration Ø alarm will go away in 2 minutes approx Ø