A detailed report on various manufacturing activities at SHRIAM PISTONS AND RINGS, suitable for mechanical undergaduates.
calibracion de valvulas motor 3054c
Fatigue analysis and Optimization of connecting rod are the modern trend in automotive engineering industry emphasis on many parameters like total deformation, life, factor of safety, stress biaxiality and fatigue sensitivity. The main scope of this
Full description
Deskripsi lengkap
for all
for all
lp orifFull description
Connecting RodFull description
Full description
ERERRER
Full description
How To Remove Tattoos Naturally
Yes, it can be done. In fact it's been around a LONG time!
Fellow tattooed friend,
I know what's on your mind.
And to answer your lingering question…
YES – there is a better way to remove your tatt
Full description
TESDA
Full description
CS-533E CP-533E Vibratory Compactor DAM00001 -UP (MACHINE) POWERED BY
...
Page 1 of 3
Fechar o SIS
Tela anterior
produtos: VIBRATORY COMPACTOR Modelo: CP-533E VIBRATORY COMPACTOR DAM Configuração: CS-533E CP-533E Vibratory Compactor DAM00001- UP (MACHINE) POWERED BY 3054C Engine
Desmontagem e Montage Montagem m 3054C Engines for Caterpillar Built Machines Número de Mídia ídia SENR5069 07 -
Data de Publicação
-
-
01/06/200 9
Data de Atualização
-
22/06/2 /2009
i02301207
Pistons and Connecting Rods - Remove SMCS - 1225-011
Removal Procedure Table 1 Required Tools Tool
Part Number
A
8S-2269
Part Description
Ridge Reamer
Qty 1
Start By: A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove". B. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install". C. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove". D. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) in order to remove the carbon ridge from the top inside surface of the cylinder liners. 2. Rotate the crankshaft until the pistons that are being removed are at the bottom center position.
CS-533E CP-533E Vibratory Compactor DAM00001 -UP (MACHINE) POWERED BY
Illustration 1
...
Page 2 of 3
g00970465
3. Remove the setscrews (1) .
Note: Do not reuse the setscrews (1) . Use new setscrews in order to secure the connecting rod cap for reassembly. 4. Remove the connecting rod cap (2) and the connecting rod bearing.
Note: Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary. Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod assembly could cause the connecting rod to fracture. 5. Put a temporary identification mark on the top of the piston in order to indicate the cylinder number that is shown on the connecting rod. Put the temporary mark on the same side as the mark that is on the connecting rods in order to ensure correct assembly of the piston and the connecting rod.
Note: Do not etch the top surface of the piston. Do not allow scratches or stamped markings in the top surface of the piston. 6. Push the pistons and the connecting rods through the top of the cylinder block. 7. Repeat Steps 2 through 6 in order to remove the remaining pistons and connecting rods.
Direitos Autorais 1993 - 2011 Caterpillar Inc. Todos os Direitos Reservados.
Thu Dec 8 12:04:42 UTC-0200 2011
CS-533E CP-533E Vibratory Compactor DAM00001 -UP (MACHINE) POWERED BY
Rede Particular Para Licenciados SIS.
...
Page 3 of 3
This document was created with Win2PDF available at http://www.win2pdf.com. The unregistered version of Win2PDF is for evaluation or non-commercial use only. This page will not be added after purchasing Win2PDF.
