Pistons and Connecting Rods - RemoveFull description
Industrial Diesel Engine
3054C 3054E
Naturally Aspirated 50-64 bkW/ 67-86 67-86 bhp
CATERPILLAR® ENGINE SPECIFICATIONS In-Line 4 Cylinder, Four-Stroke-Cycle Diesel Bore — mm (in) . . . . . . . . . . . . . . . . . . . . . 105 (4.13) Stroke — mm (in). . . . . . . . . . . . . . . . . . . . 127 (5 (5.00) Disp Di spla lace ceme men nt — li lite terr (cu (cu in in)) . . . . . . . . . . 4. 4.41 41 (2 (269 69)) Combustion Sys System . . . . . . . . . . . . Direct inj injection Rotation Rotat ion (from flywh flywheel eel end) end) . . Coun Counterclo terclockwis ckwise e Capacity for Liquids — L (U.S. qts) Coo Co oli lin ng Sys Syste tem m (en (engi gin ne on only ly). ). . . . . . . . . . 7 (7. (7.4) 4) Lube Lu be Oi Oill Syst System em (re (refi fill ll)) typi typica cal. l. . . . . . . . 6. 6.9 9 (7.3 (7.3)) Weight, Net Dry (approximate) — kg (lb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 (641)
Engine Pictured with Optional Equipment
BENEFITS
HIGH PERFORMANCE Horsepower and torque capabilities optimized.
QUALITY BY DESIGN FOR DURABILITY Product design and process improvements have been used from early stages to enhance engine reliability and durability.
CLEAN AND QUIET POWER Cleaner, meeting EPA Tier 2 emissions standards and free from visible smoke throughout operational speed range. Quieter, with up to 3 dBA reduction in bare engine noise.
EASY LOW-COST MAINTENANCE Convenient positioning of service points for easy accessibility. Service intervals at 500 hours as standard.
WEB SITE For additional information on all your power requirements, visit www.cat.com.
LEHH2492-01
STANDARD EQUIPMENT Cast iron engine block Flywheel and flywheel housing Ecoplus oil and fuel filters Electronic control module (on 3054E) Glow plug starting aid Integral inlet manifold Cast iron exhaust manifold — center side outlet Gear-driven coolant pump Alternator — 12V and 24V; 55, 65, 85, 100 amp Provision for PTOs Choice of cooling fans Starter motor — 12V and 24V Plastic J2044 fuel system standard Choice of lube oil sump Choice of dipstick positions Choice of filter positions Choice of water outlet Optional balancer
Pa ge 1 of 2
3054C/3054E
INDUSTRIAL ENGINE
PERFORMANCE DATA Naturally Aspirated 3054C
3054E
300 290 280 m N270 •
260
220
300
e u t f 200 q r b o l T
290
250
e u t f 200 q r b o l T
280 m N270 •
260 250
180
180
65
65 80
r e p h 70 w o b P
W55 k b 45 1400
220
60 1600
1800
2000
2200
80
r e p h 70 w o b P
W55 k b 45
2400
1400
Engine Speed rpm
60 1600
1800
2000
2200
2400
Engine Speed rpm
Gross Intermittent Power = SAE J1995 Other ratings are available. Lower power ratings should not be read from these curves.
DIMENSIONS Length
mm (in)
663 (26.1)
Width
mm (in)
563 (22.2)
Height
mm (in)
775 (30.5)
Weight
kg (lb)
291 (641)
Note: Dimensions and weight depend on final specifications.
RATING DEFINITIONS AND CONDITIONS Intermittent is the horsepower and speed capability of the engine which can be used for about one hour, followed by an hour of operation at or below the continuous rating. Continuous is the horsepower and speed capability of the engine which can be used without interruption or load cycling.
Additional ratings are available for specific customer requirements. Consult your Caterpillar dealer.
Ratings are based on SAE J1995 standard conditions of 100 kPa (29.61 in Hg) and 25° C (77° F). These ratings also apply at ISO/TR14396, standard conditions and to DIN6271 and BS5514 standard conditions of 100 kPa (29.61 in Hg), 27° C (81° F) and 30% relative humidity. Fuel consumption is based on fuel oil having an LHV of 42 780 kJ/kg (18 390 Btu/lb) and weighing 845-850 g/liter (7.052-7.094 lb/U.S. gal). Power ratings are based on engine equipped with fuel, lube oil, and jacket water pumps but without fan.
Materials and specifications are subject to change without notice. LEHH2492-01 (2-03)