3054c calibracion

16/1 16/11/2 1/2016 016

420E 420E Backhoe Backhoe Loader Loader Single Tilt Til t Center Center Pivot HLS00001 HLS00001-U -UP P (M ACHINE) ACHIN E) POWERED BY 3054C 3054C Engine Engine(SEBP37 (SEBP3703 03 - 72) 72) - Documentation Documentation

Previous Screen

Welcome: r080amoc Product: BACKHOE LOADER Model: 420E BACKHOE LOADER HLS Configuration: 420E Backhoe Loader Single Tilt Center Pivot HLS00001-UP (MACHINE) POWERED BY 3054C Engine

Testing and Adjusting 3054C Engines for Caterpillar Built Machines Me dia Numbe r -RENR2415-14

Publicat ion Dat e -05.01. 2015

Dat e Updat ed ed -05. 28. 2015

i06025710

Engine Valve Lash - Inspect/Adjust SMCS - 1102-025

To prevent possible injury, do not use the starter to turn the flywheel. Hot engine components can cause burns. Allow additional time for the engine to cool before measuring valve clearance.

Specifications Table 1 Inlet Valves

Exhaust Valves

Valve Lash (Stopped Engine)

0.20 mm (0.008 inch)

TC Compression Stroke

1 and 2

1 and 3

TC Exhaust Stroke (1)

3 and 4

2 and 4

0.45 mm (0.018 inch)

1,3,4,2 (2)

Firing Order ( 1 ) 360° from TC compression stroke ( 2 ) The No. 1 cylinder is at the front of the engine.

Table 2 TC Compression Stroke Valve Lash Cylinders

Inlet Valves

Exhaust Valves

0.20 mm (0.008 inch)

0.45 mm (0.018 inch)

1 and 2

1 and 3

Table 3 TC Exhaust Stroke (3)

Inlet Valves

Exhaust Valve

https://sis.cat.com/si https://sis.cat.com/si sweb/sisweb/techdoc/te sweb/sisweb/techdoc/techdo chdoc_print_p c_print_page age.jsp?returnu .jsp?returnurl rl =/si sweb/sisweb sweb/sisw eb/mediasea /mediasearch/mediahe rch/mediaheade aderi ri nfoframeset.jsp&calledpa nfoframeset.jsp&calledpage=/sis… ge=/sis…

1/5

16/1 16/11/2 1/2016 016


Valve Lash

0.20 mm (0.008 inch)

0.45 mm (0.018 inch)

3 and 4

2 and 4

Cylinders ( 3 ) Position for No. 1 cylinder

Table 4 Torque for Adjustment Locknut

27 N·m (20 lb ft)

Introduction Refer to Specifications, "Engine Design" for the location of the cylinder valves. If the valve lash requires adjustment several times in a short period of time, excessive wear exists in a different part of the engine. Find the problem and make necessary repairs in order to prevent more damage to the engine. Not enough valve lash can be the cause c ause of rapid wear of the camshaft and valve lifters. Not enough valve lash can indicate that the seats for the valves are worn. Valves become worn due to the following causes: Fuel injection nozzles that operate incorrectly Excessive dirt and oil are present on the filters for the inlet air. Incorrect fuel settings on the fuel injection pump. The load capacity of the engine is frequently exceeded. Too much valve lash can cause broken valve stems, springs, and spring retainers. Too much valve lash can be an indication of the following problems: Worn camshaft and valve lifters Worn rocker arms Bent pushrods Broken socket on the upper end of a pushrod Loose adjustment screw for the valve lash If the camshaft and valve lifters show rapid wear, look for fuel in the lubrication oil or dirty lubrication oil as a possible cause.

Check Procedure Valve Lash Check An adjustment is NOT NECESSARY if the measurement of the valve lash is in the acceptable range. Check the valve lash while the engine is stopped. The temperature of the engine does not change the valve lash setting. Table 5 https://sis.cat.com/si https://sis.cat.com/si sweb/sisweb/techdoc/te sweb/sisweb/techdoc/techdo chdoc_print_p c_print_page age.jsp?returnu .jsp?returnurl rl =/si sweb/sisweb sweb/sisw eb/mediasea /mediasearch/mediahe rch/mediaheade aderi ri nfoframeset.jsp&calledpa nfoframeset.jsp&calledpage=/sis… ge=/sis…

2/5

16/1 16/11/2 1/2016 016


Inlet Valves

Exhaust Valves

0.20 mm (0.008 inch)

0.45 mm (0.018 inch)

TC Compression Stroke

1 and 2

1 and 3

TC Exhaust Stroke (1)

3 and 4

2 and 4

Valve Lash (Stopped Engine)

Firing Order

1,3,4,2 (2)

( 1 ) 360° from TC compression stroke ( 2 ) The No. 1 cylinder is at the front of the engine.

If the measurement is not within the acceptable clearance, adjustment is necessary.

Adjustment Procedure Valve Lash Adjustment Note: The No. 1 cylinder is at the front of the engine.

Illu stration 1

g 0 0 3 23 9 0 3

Setting Setting the valve lash (1) Adjustment screw (2) Feeler gauge

Accidental engine starting can cause injury or death to personnel. To prevent accidental engine starting, turn the ignition switch to the OFF position, place a do not operate tag at the ignition switch location and disconnect and tape the electrical connection to the stop solenoid that is located on the fuel injection pump.


3/5

16/1 16/11/2 1/2016 016


Remove the valve mechanism cover and perform the following procedure in order to adjust the valve lash: 1. Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". Table 6 TC Compression Stroke Valve Lash

Inlet Valves

Exhaust Valves

0.20 mm (0.008 inch)

0.45 mm (0.018 inch)

1 and 2

1 and 3

Cylinders

2. Adjust the valves according to Table 6. 3. Lightly tap the rocker arm at the top of the adjustment screw with a soft mallet. This will ensure that the lifter seats against the camshaft. 4. Loosen the adjustment locknut. 5. Place the appropriate feeler gauge between rocker arm and the valve stem. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve stem. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge. Remove the feeler gauge. 6. Tighten the adjustment locknut to a torque of 27 N·m (20 lb ft). Do not allow the adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve lash after tightening the adjustment locknut. 7. Rotate the engine by 360 degrees. The engine will be on TC compression stroke for cylinder 4. Table 7 TC Exhaust Stroke (3) Valve Lash

Inlet Valves

Exhaust Valve

0.20 mm (0.008 inch)

0.45 mm (0.018 inch)

3 and 4

2 and 4

Cylinders ( 3 ) Position for No. 1 cylinder

8. Adjust the valves according to Table 7. 9. Lightly tap the rocker arm at the top of the adjustment screw with a soft mallet. This will ensure that the lifter seats against the camshaft. 10. Loosen the adjustment locknut. 11. Place the appropriate feeler gauge between rocker arm and the valve stem. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve stem. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge. Remove the feeler gauge. 12. Tighten the adjustment locknut to a torque of 27 N·m (20 lb ft). Do not allow the adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve lash after tightening the adjustment locknut. Copyright 1993 - 2016 Caterpillar Inc. All Rights Reserved.

Wed Nov 16 2016 22:29:16 GMT-0500 (Hora est. Pacífico, Sudamérica) r080amoc


4/5

16/1 16/11/2 1/2016 016


Private Network For SIS Licensees.


5/5

3054c calibracion

Recommend Documents