Stopuri Spate: [Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 9: Debifati toate casutele sau modificati casuta DEC in cifra 0 (zero) [Transfer Coding!] [Do It!]
E08C8F0700041A00000A00000F000000000959435C
dec era 10
Activare Coming Home & Leaving Home [Select] [09 - Cent. Elect.] [07 - Coding] [Long Coding Helper] Byte 0: - bifati Bit 5 (Assistance Driving Light - Leaving Home active) - bifati Bit 7 (Coming-Home active) [Transfer Coding!] [Do It!]
Modificare timpilor pt Coming Home & Leaving Home Select] [09 - Cent. Elect.] [10 - Adaptation] Channel 01: numarul de secunde care doriti ca coming home sa fie activ - de la 0 pana 120 Channel 02: numarul de secunde care doriti ca leaving home sa fie activ - de la 0 pana 120 [Test] [Save] [Done, Go Back]
Afisarea vitezei pe ecranul Radio CD. [Select] [56 - Radio] [10 - Adaptation] Channel 02: 0 = dezactivare / 1 = activare (afisarea vitezei in km/h pe display-ul radioului) [Test] [Save] [Done, Go Back]
Dupa aceasta operatie se apasa butonul meniu (de la radio-CD) si in acelasi timp se apasa pe butonul de pornire (power).
Inchidere proiectoare cand dai flash sau faza lunga [Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 17: bifati Bit 5 (Front Fog lights deactivated with High Beam) [Transfer Coding!] [Do It!]
Regenerarea filtrului de particule (DPF). NOTA: Aceasta procedura se efectueaza NUMAI in cazul in care procedura descrisa in manualul de utilizare a autovehiculului nu functioneaza!! Testat pe motor de 2.0 TDI 140 cp., functioneaza cu Vag Com 805 sau 812.4 Contactul PUS, motorul pornit 002 , campul nr 4)
, apa peste 50 grade ( vezi temperatura in Measuring Blocks canalul
A se urmari valorile DPF in Measuring BLocks canalul 075 , casuta nr 3. În cazul în care valoarea de încărcare este de peste Specificaţii (din casuta numarul 2), atunci filtrul trebuie inlocuit, altfel poate crapa in timpul regenerarii.
Consumatorii electrici si mecanici anexati motorului sa fie porniti (incalizre scaune, clima, lumini, etc, etc) EGT-ul ( gazele de evacuare INAINTE DE TURBINA ) sa fie peste 700 °C inainte de a porni testul. [Select] [01 - Engine] [Coding-II - 11] ( doar varianta 805 stie aceasta optiune ) • Activeaza Regenerarea prin introducerea codului 21295. [Do It!] [Meas. Blocks - 08] selecteaza Groups-canalele 070 and 075. [Go!]
Semnificatii : Canal 070 casuta nr. 1: Regeneration Status (xxxxxxx1 = Normal Regeneration active, xxxxxx1x = Forced Regeneration active) Canal 070 casuta nr. 3: Regeneration Counter/Timer Durata Canal 075 casuta nr. .1: EGT inainte de turbina Canal 075 casuta nr. 2: EGT inainte de Particle Filter Canal 075 casuta nr.3: Incarcarea Particle Filter - Particle Filter Load Canal 075 casuta nr.4: EGT dupa Particle Filter Porniti si urmariti valorile mentionate mai sus. Se ruleaza masina cu 30-60 km/h - la 1500-2500 rot/min ,durata aprox. 15-20 Minute . Sofati pana cand Particle Filter Load devine cat mai aproape de valoarea 0% (dar in intervalul de timp mentionat). Daca valorea nu scade atunci conditiile de rulare nu sunt corespunzatoare cu datele de aici sau motorul tau are probleme mecanice sau electronice ( supape, tacheti, axa cu came, injectoare, compresie - sau debimetru, senzor apa, actuatori turbo/egr)
Anularea diagnosticarii "eroare bec ars" pentru semnalizare Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 18: - debifezi Bit 5 (Cold Diagnosis Turn Signals active) - debifezi Bit 7 (Cold Diagnosis Side Turn Signals active)
[Transfer Coding!] [Do It!]
Schimbarea limba pe afisajul display-ului [Select] [17 - Instruments] [10 - Adaptation] Channel 02 : 00001 - German 00002 - English 00003 - French 00004 - Italian 00005 - Spanish 00006 - Portuguese 00007 - no text 00008 - Czech [Test] [Save] [Done, Go Back]
Inchiderea automata a masinii dupa viteza de 15km/h [Select] [46 - Cent. Conv.] [10 - Adaptation] Channel 03: Auto Lock after 15km/h (1 = Activate / 2 = Deactivate) [Test] [Save]
Deschiderea automata a masinii dupa scoaterea cheii din contact [Select] [46 - Cent. Conv.] [10 - Adaptation] Channel 04: Auto Unlock after removing the key (1 = Activate / 2 = Deactivate)
[Test] [Save] [Done, Go Back]
Optional se mai pot seta ca la inchiderea/deschiderea masinii sa se aprinda avariile sau sa se auda un clacson scurt Pt acestea, modificari si: Optional channels - flash blinkers or sound horn said:
Channel 05: Unlock, horn sounds (1 = Activate / 2 = Deactivate) Channel 06: Lock, horn sounds( 1 = Activate / 2 = Deactivate) Channel 07: Unlock, turn signals flash (1 = Activate / 2 = Deactivate) Channel 08: Unlock, turn signals flash (1 = Activate / 2 = Deactivate)
Programare cheie Select] [17 - Instruments] [Login - 11] [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK]
VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do It!]
[Adaptation - 10] Enter 21 in "Channel Number" [Read] The "Stored Value" is the number of keys currently matched. Enter "new value" of 0 [Save]
This clears out the old key-matchings. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys [Save]
[Done, Go Back] [Close Controller, Go Back - 06] Switch ignition off and remove key
Insert next key to ignition and switch ignition on again. The warning light for the Immobilizer will light up for ~2 seconds, then go out. Switch ignition off and remove key
Repeat step 16 with each key until all keys have been matched
SEAT BELT CHIME: Control Module Coding Select 17 (Instrument Cluster) Coding -> Function 07 00??x0x: Extra-Options +01 - Brake Pad Warning active +02 - Seatbelt Warning active +04 - Washer Fluid Warning active +16 - Sedan (Jetta) So if you wanted everything active.... 0023x0x where x is the value of the original coding, let's say it was set there from the factory. To remove seat belt warning, just subtract the 02.... so it would now be: 0021x0x My stock coding: 0023203 With no seat belt chime: 0021203
Retragerea pistonaselor pentru inlocuirea placutelor de frana pe spate se face cu vag-com! Frane de parcare---inlocuire placute: [Selectare module] [53 - Frana de parcare] [Setare de baza - 04] Grup: 007 [Start!] Activare setare de baza [CON/DEC/Urmator] Etrierul se deschide. [Gata, inapoi] Se inlocuiesc placutele. Grupul 006 in setare de baza va readuce pistonul. Grupul 010 in setare de baza are caracter de test: in prima faza etrierul se deschide 1x, dupa care strange de 3x.
Activare inchidere automata a geamurilor tinand apasat butonul doar 2 secunde [Select] [46 - Central Conv.] [07 - Coding] [Long Coding Helper] Byte 6: - bifati Bit 6 (Comfort function autom. closing) [Transfer Coding!] [Do It!]
Activare DRL(s) pe proiectoare la 50% din intensitate [Select] [09 - Central Electric] [07 - Coding]
[Long Coding Helper] Byte 00: - bifati Bit 4 (Daytime Running Lights (North America)) Byte 17: - bifati Bit 4 (Daylight Running Light via Front Fog Lights) Byte 20: - in casuta DEC modificati valoare (in procente) in 50 [Transfer Coding!] [Do It!]
Respectiva valoare inscrisa in casuta DEC poate fii modificata dupa bunul plac
Deschiderea pistoanelor pentru inlocuirea placutelor de frana pe spate [Select] [53 - Parking Brake] [04 - Basig Settings] Grup: 007 [Start!] Activating basic settings [CON/DEC/Next] (Aici etrierul se va deschide.) [Done, Go back!]
Acum se pot inlocui placutele de frana
Inchiderea pistoanelor dupa inlocuirea placutelor de frana pe spate [Select] [53 - Parking Brake] [04 - Basig Settings] Grup: 006 [Start!] Activating basic settings [CON/DEC/Next] (Aici etrierul se va inchide.) [Done, Go back!]
Nota: Grup-ul 010 in "basic settings" are caracter de test; in prima faza etrierul se deschide 1x, dupa care strange de 3x.
Functia "cornering" pe proiectoare! NOTA: Aceasta functie merge activata doar la masiniile produse DUPA iulie 2007! [Select] [09 - Cent. Elect.] [10 - Coding] [Long Coding Helper] Byte 23: - bifati Bit2 (Internal Turn Light Control Algorithm active) - selectia la Bit-ul 3-4: 08 Turn Lights via Fog Lights [Transfer Coding!] [Do It!]
Sunet Alarma [Select] [46 - Cent. Conv.] [10 - Adaptation] Channel 10: Alarm Horn Aici alegi între biţii 0,1,2,3 care-ţi convine. [Save] [Done, Go Back] M-am jucat si eu in vară puţin la alarmă şi reţin că sunt două feluri de tonalităţi grupate pe biţii 0 şi 2 (seamănă cât de cât a alarmă) şi pe biţii 1 şi 3 (piuie) şi dacă-mi amintesc bine, din cele două grupuri de sunete pe biţii 1 şi 3 se aude mai tare.
IMMO II Determining IMMO-ID [Select] [25 - Immobilizer] Look at the "Component" field. The 14-digit string in the Immo-ID. [Close Controller, Go Back - 06]
Key Matching Prerequisites:
You can match up to 8 keys. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place. Battery voltage at least 12.0 V.
[Select] [25 - Immobilizer] [Meas. Blocks - 08] Select Block 001. [Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner. [Done, Go Back]
[Login - 11] There are 2 possibilities how to enter a PIN, choose the one that applies for you. 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!]
[Adaptation - 10] Enter 01 in "Channel Number" (if not available use Channel 21). [Read] The "Stored Value" is the number of keys currently matched. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. The old keys are automatically beeing cleared. [Save] [Done, Go Back] [Close Controller, Go Back - 06]
Repeat the following steps until all keys have been matched: Switch ignition off and remove key. Insert next key to ignition and switch ignition on again. The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key. Note: The above steps after saving the adaptation, should not exceed 30/60 seconds!
IMMO III - Immobilizer III Key Matching (Cluster) Determining IMMO-ID & VIN [Select] [17 - Instruments] Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID. [Close Controller, Go Back - 06]
---OR--[Select] [17 - Instruments] [Meas. Blocks - 08] Select Block 081. [Go!] The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.. [Done, Go Back] [Close Controller, Go Back - 06]
Key Matching Prerequisites:
All keys are either new or were adapted to this car (IMMO-ID) before. You can match up to 8 keys. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
Battery voltage at least 12.5 V.
[Select] [17 - Instruments] [Meas. Blocks - 08] Select Block 022. [Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner.
Select Block 024. [Go!] Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes).
If the lock times are NOT 0: Do NOT switch off the ignition! Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3. [Done, Go Back]
[Login - 11] There are 2 possibilities how to enter a PIN, choose the one that applies for you. 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!]
IMMO III - Immobilizer III Key Matching (Separate) Determining IMMO-ID & VIN [Select] [25 - Immobilizer] Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID. [Close Controller, Go Back - 06]
---OR--[Select] [25 - Immobilizer] [Meas. Blocks - 08] Select Block 081. [Go!] The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.. [Done, Go Back] [Close Controller, Go Back - 06]
Key Matching Prerequisites:
All keys are either new or were adapted to this car (IMMO-ID) before. You can match up to 8 keys. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place. Battery voltage at least 12.0 V.
[Select] [25 - Immobilizer] [Meas. Blocks - 08] Select Block 001. [Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner.
Select Block 003. [Go!] Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes).
If the lock times are NOT 0: Do NOT switch off the ignition! Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3. [Done, Go Back]
[Login - 11]
There are 2 possibilities how to enter a PIN, choose the one that applies for you. 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN [Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!]
[Adaptation - 10] Enter 01 in "Channel Number". [Read] The "Stored Value" is the number of keys currently matched. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. The old keys are automatically beeing cleared. [Save] [Done, Go Back] [Close Controller, Go Back - 06]
Repeat the following steps until all keys have been matched: Switch ignition off and remove key. Insert next key to ignition and switch ignition on again. The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key. Note: The above steps after saving the adaptation, should not exceed 60 seconds!
IMMO III - Immobilizer III Key Matching (Kessy) Determining IMMO-ID & VIN [Select] [05 - Acc/Start Auth.] [Meas. Blocks - 08] Select Block 081.
[Go!] The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.. [Done, Go Back] [Close Controller, Go Back - 06]
Key Matching Prerequisites:
Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger. You can match up to 8 keys. All keys are either new or were adapted to this car (IMMO-ID) before. While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place. If all Keys are new OR the first inserted Key is new, the Ignition will NOT switch ON with this key. Put the first Key into the ignition Lock, but do NOT switch ON the ignition. Press and Hold the Brake Pedal for 20 Seconds to wake up the Diagnostic Databus. [Select] [05 - Acc/Start Auth.] [Meas. Blocks - 08] Select Block 022. [Go!] The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner.
Select Block 023. [Go!] Make sure the shown lock times in field 1, 2, 3 and 4 are 0 (each field represents a time in minutes).
If the lock times are NOT 0: Do NOT switch off the ignition! Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-4. [Done, Go Back]
[Sec. Access - 16] There are 2 possibilities how to enter a PIN, choose the one that applies for you. 4-digit PIN Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234. 7-digit PIN
[Use 7-digit PIN/SKC] Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. [OK] VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". [Do it!]
[Adaptation - 10] Enter 21 in "Channel Number". [Read] The "Stored Value" is the number of keys currently matched. Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. The old keys are automatically being cleared. [Save] [Done, Go Back] [Close Controller, Go Back - 06]
Switch Ignition OFF and remove Key, Steering Lock should engage. Insert first Key again and switch Ignition ON. The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key. Repeat the following steps until all keys have been matched: Switch Ignition OFF and remove Key, Steering Lock should engage. Insert next Key to Ignition and switch Ignition ON again. The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key. Note: The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds.!
Control Module Coding Select 17 (Instrument Cluster) Coding -> Function 07 00??x0x: Extra-Options +01 - Brake Pad Warning active +02 - Seatbelt Warning active +04 - Washer Fluid Warning active +16 - Sedan (Jetta) scazi 2 din 7
pentru stopuri spate: [Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 9: Debifezi toate casutele sau modifici casuta DEC in cifra 0 (zero) [Transfer Coding!] [Do It!]
Deschidere selectiva [Select] [46 - Cent. Conv.] (35 - Cent. Locking pentru masinile cu geamuri manuale) [Recode - 07] Notati-va codul software pentru referinte ulterioare. Uitati-va la codul software existent. Daca aveti descuiere selectiva (o apasare pe butonul telecomenzii descuie usa soferului si a doua descuie toate celelalte usi) ultimul digit al codului trebuie sa fie un numar par. Pentru a activa descuierea tuturor usilor simultan, adaugati 1 la valoarea codului. Introduceti noul cod din 5 digiti. [Do It!] Incuiat/Descuiat la viteza de 15 Km/h Claxon/Avarii [Select] [46 - Cent. Conv.] (35 - Cent. Locking pentru masinile cu geamuri manuale) [Adaptation - 10] Canalul (03..08) Valorile adaptarilor (1 = on, 2 = off) [Save] Canalul 03 Auto Lock Canalul 04 Auto Unlock Canalul 05 Unlock, horn sounds Canalul 06 Lock, horn sounds Canalul 07 Unlock, turn signals flash Canalul 08 Unlock, turn signals flash
Reglare turatie ralanti
Pentru realizarea acestei adaptari trebuie sa folositi un cod pentru a va loga. Codul este 12233. [Select] [01 - Engine] [Login - 11] introduceti codul 12233 pentru a activa adaptarile speciale [Do It!] [Adaptation - 10] Selectati canalul 2: turatia de ralanti. Valoarea din fabricatie este 32768 corespunde unei valori de 903 rpm. Turatia se modifica prin cresterea sau scaderea valorii date. [Test] Observati cum se modifica ralanti-ul si daca sunteti multumiti [Save]
Schimbarea limbii pe BC [Select] [17 - Instruments] [Adaptation - 10] Selectati canalul ales: canalul 4: limba aleasa pentru afisaj, cu urmatorile valori: 00001 Germana 00002 Engleza 00003 Franceza 00004 Italiana 00005 Spaniola 00006 Portugheza [Test] Observati cum se modifica limba afisata pe display. [Save]
Modificare distanta senzori de parcare :
Inainte de a face orice modificare notati-va valoarea existenta. Folosirea gresita a adaptarilor poate conduce la nefunctionalitatea motorului, asa ca orice modificare o faceti pe propriul risc ! Adaptarea functioneaza numai la modelele care dispun de sistemul de avertizare sonora a obstacolelor la parcare. [Select] [Display] - less common modules [76 - Parking Aid] [Adaptation - 10] introduceti valoarea numarului canalului ales: canalul 1 : volumul avertizarii marsarier (valori 2 - 7) canalul 2 : frecventa avertizarii marsarier (valori 0 - 4) canalul 3 : volumul avertizarii fata (valori 2 - 7) canalul 4 : frecventa avertizarii fata (valori 0 - 4) [Test] Observati cum se modifica nivelul si frecventa avertizarii sonore, si daca sunteti multumiti [Save] Reglare pozitie de referint a farurilor cu Xenon OEM Inainte de a face orice modificare notati-va valoarea existenta. Folosirea gresita a adaptarilor poate conduce la nefunctionalitatea motorului, asa ca orice modificare o faceti pe propriul risc ! [Select] [Display] - less common modules [55 - H Light Range] notati-va valoarea Soft. coding. ea reprezinta valoarea presetata si in cazul in care nu obtineti rezultatele asteptate puteti reveni la aceasta valoare. [Recode - 07] modificati valoarea din campul software coding dupa cum urmeaza: scaderea acestei valori "ridica" farurile si invers.
modificati valoarea in incremente relativ mici 5 - 10 [Do it] Acum este nevoie de recalibrarea senzorirol pentru autoajustarea nivelului farurilor. Din modulul deja selectat 55 - headlight range [Basic Settings - 04] [Group 001] asteptati cateva secunde pana cand primul camp se modifica din "wait" in "set" acum mergeti un [Group 002] asteptati pana cand afiseaza "learned" daca doriti sa mai modificati in continuare pozitia reluati procedura pana cand obtineti rezultatul dorit.
Combinatii luminoase la bord Inainte de a face orice modificare notati-va valoarea existenta. Folosirea gresita a adaptarilor poate conduce la nefunctionalitatea motorului, asa ca orice modificare o faceti pe propriul risc ! [Select] [17 - Instruments] [Login - 11] introduceti codul 11463 sau 01283 sau 13861 pentru a activa adaptarile speciale [Do It!] [Adaptation - 10] introduceti valoarea numarului canalului ales: canalul 19 : modul de iluminare a bordului (indicatoare si scala) notati-va valoarea existenta si nu modificati decat cifra cea mai din stanga. 0xxxx totul se ilumineaza la pornirea luminilor 1xxxx indicatoarele aprinse tot timpul (odata cu contactul de cheie) 2xxxx scala aprinsa tot timpul (odata cu contactul de cheie)
3xxxx indicatoarele si scala aprinsa tot timpul (odata cu contactul de cheie) [Test] Observati cum se modifica iluminarea display-ului de bord si daca sunteti multumiti. [Save] Exact. Mai in detaliu, este vorba despre Instruments / Adaptation / Channel 19 unde ai un numar din 5 cifre, prima reprezentand modul de iluminare: - 0 (sau absenta) = nimic iluminat - 1 = doar indicatoarele iluminate - 2 = doar cifrele iluminate - 3 = indicatoarele si cifrele iluminate Anulare centura Rectific codul dupa un studiu mai amanuntit : 0007105 unde 00...break pad (frana de mana) 07 seat belt(centura) 1 locatia :europe 05 .lichidul de la stergatoare Modifici 07 (-02) in 05 si anulezi semnalul de centura , nu mai apare nici in bord . Iar unu reprezinta locatia sau limba 1 europe , 2 usa 3... Pilot Automat Select] [01 - Engine] [Login - 11] Enter 11463 to activate cruise control [Do It!] After doing this procedure, there should be a letter "G" in the Component field
Volkswagen Golf Auto Rain Closing Windows and Sunroof An undocumented feature on the Golf MKV is automatic rain closing windows. The only requirement is having a
RegenLichtSens (RainLightSensor) Operation of the system
Rain closing activates only when the car has been locked. The windows and sunroof if fitted will close automatically after 24 hours.
To activate the feature there are two steps, one is to enable the feature and one is to enable the menu if there is a full height MFD to give the option to enable or disable. If there is no full height MFD the system will still operate correctly but to enable or disable you will need to use Vagcom/VCDS. If the car is fitted with an alarm and the interior sensors these will need to be disabled by pressing the button on the B pillar before locking the car as operation of the sunroof and windows may activate the alarm. The wiper stalk may need to be in the automatic/intermittent position to operate. Step 1 – Enable Auto Rain Closing 1. Open the Central Electronics Controller (09) and click on the “Coding” option. 2. Click the drop down box and choose the RegenLichtSens (RainLightSensor)
3. Note the software coding (00)208933) (most cars have different codings) (00)217125 4. Convert to Hex (0)3 30 25 (0)3 50 25 5. Add 4 to the left hand value Hex (0)7 30 25 (0) 7 50 25 6. Convert to Decimal (00)471077 and replace the old coding. (00)479269 If you’re unclear on the conversion steps see the Decimal to Hex and Hex to Decimal conversion guide.
Step 2 – Enable Menu to Enable/Disable (optional) 1. Open the Comfort System Controller (46)
2. In long coding change Byte 09 to Hex 02
Example 13 90 06 88 51 03 48 3F 2D 04 05 8F B0 08 0A 04 88 9C 00 to 13 90 06 88 51 03 48 3F 2D 02 05 8F B0 08 0A 04 88 9C 00 The menu will now give you the option to turn on or off the Rain Closing Feature. Testing To test wind down the windows and open sunroof if fitted, lock the car. Wait around 2 minutes and pour some water on the rain sensor (mounted on the glass behind the rear vision mirror) and after a short delay the windows and sunroof will close. Issues There are really no issues with enabling this feature. There have been a few reports of people getting a fault appearing in their Central Electronics Controller (09) from time to time “02071 –
Local Databus- 004 – No Signal/Communication – Intermittent” but the system operates correctly and for some people depending on the revision of the RegenLichtSens where it just doesn’t operate.
Inchidere Geamuri si Trapa din telecomanda [Select] [46 - Cent. Conv.] [Long Coding - 07] [Long Coding Helper] Click on each of the Byte numbers in step 3) and you'll see the selectable options below. - debifati bit
"Comfort function power windows/sunroof via remote control inactive"
- bifati bit "Comfort opening power windows via remote control active" - bifati bit "Comfort closing power windows via remote control active" - bifati bit "Closing sunroof via remote control active" [Transfer Coding!] [Do It!]
Pentru stingerea centrului stopurilor spate (sa ramana doar cerculetele pe pozitie): CODE [Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 9: Debifati toate casutele sau modificati casuta DEC in cifra 0 (zero) [Transfer Coding!] [Do It!]
Activare semnalizari fata la intesitate redusa (USA Style)
Select] [09 - Centr. Elect.] [07 - Coding] [Long Coding Helper] Byte 7: - bifati Bit 1 (Turn Signal as Parking Light [USA/Canada]) - in casuta DEC modificati valoare (25-35% sau cat doriti) cat sa fie de iluminate [Transfer Coding!] [Do It!]
Din proprie experienta va spun ca un 35% intensitate este foarte ok. Ce sare de 40% deja devine deranjat si nici nu ajuta la o mai buna iluminare.
