Uplink CoMP (Joint RX)(GBSS19.1_01).pdf

GSM BSS GBSS19.1

Uplink CoMP (Joint RX) Feature Parameter Description Issue

01

Date

2017-03-15

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2017. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd. Address:

Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China

Website:

http://www.huawei.com

Email:

[email protected]

Issue 01 (2017-03-15)

Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

i

GSM BSS Uplink CoMP (Joint RX) Feature Parameter Description

Contents

Contents 1 About This Document.................................................................................................................. 1 1.1 Scope.............................................................................................................................................................................. 1 1.2 Intended Audience.......................................................................................................................................................... 1 1.3 Change History............................................................................................................................................................... 1

2 Overview......................................................................................................................................... 3 2.1 Introduction.................................................................................................................................................................... 3 2.2 Concepts......................................................................................................................................................................... 3 2.3 Benefits........................................................................................................................................................................... 4 2.4 Architecture.................................................................................................................................................................... 4 2.5 Feature Support by NE................................................................................................................................................... 5

3 Technical Description...................................................................................................................6 3.1 Uplink CoMP..................................................................................................................................................................6 3.1.1 Decision on Starting Uplink CoMP in Connected Mode............................................................................................ 6 3.1.2 Decision on Starting Uplink CoMP During Assignment............................................................................................ 7 3.1.3 Decision on Starting Uplink CoMP During Handover................................................................................................7 3.1.4 Decision on Coordinating Cell Switch/Stopping of Uplink CoMP.............................................................................8 3.1.5 FACCH Frame Check..................................................................................................................................................9 3.1.6 Combination and Decoding......................................................................................................................................... 9 3.2 Enhanced Signaling Frame Decoding............................................................................................................................ 9 3.2.1 Enhanced SDCCH Signaling Frame Decoding........................................................................................................... 9 3.2.2 Enhanced TCH Signaling Frame Decoding.............................................................................................................. 10

4 Related Features...........................................................................................................................11 5 Network Impact........................................................................................................................... 14 6 Engineering Guidelines............................................................................................................. 15 6.1 When to Use Uplink CoMP..........................................................................................................................................15 6.2 Required Information................................................................................................................................................... 15 6.3 Planning........................................................................................................................................................................ 15 6.3.1 RF Planning............................................................................................................................................................... 15 6.3.2 Network Planning...................................................................................................................................................... 15 6.3.3 Hardware Planning.................................................................................................................................................... 16 6.4 Deployment.................................................................................................................................................................. 17 Issue 01 (2017-03-15)


ii


Contents

6.4.1 Requirements............................................................................................................................................................. 17 6.4.2 Precautions.................................................................................................................................................................18 6.4.3 Hardware Installation................................................................................................................................................ 18 6.4.4 Data Preparation and Feature Activation...................................................................................................................18 6.4.4.1 Data Preparation..................................................................................................................................................... 18 6.4.4.2 Using the CME....................................................................................................................................................... 20 6.4.4.3 Using MML Commands......................................................................................................................................... 21 6.4.4.4 MML Command Examples.................................................................................................................................... 21 6.4.5 Activation Observation..............................................................................................................................................21 6.4.6 Deactivation...............................................................................................................................................................22 6.4.6.1 Using the CME....................................................................................................................................................... 22 6.4.6.2 Using MML Commands......................................................................................................................................... 22 6.4.6.3 MML Command Examples.................................................................................................................................... 22 6.5 Performance Monitoring...............................................................................................................................................23 6.6 Parameter Optimization................................................................................................................................................ 23 6.7 Troubleshooting............................................................................................................................................................ 24

7 Parameters..................................................................................................................................... 25 8 Counters........................................................................................................................................ 32 9 Glossary......................................................................................................................................... 41 10 Reference Documents............................................................................................................... 42

Issue 01 (2017-03-15)


iii


1

1 About This Document

About This Document

1.1 Scope This document describes the GBFD-191201 Uplink CoMP (Joint RX) feature, including its technical principles, related features, network impact, and engineering guidelines. NOTE

"Uplink CoMP" refers to the Uplink CoMP (Joint RX) feature in this document.

1.2 Intended Audience This document is intended for personnel who: l

Need to understand the features described herein

l

Work with Huawei products

1.3 Change History This section provides information about the changes in different document versions. There are two types of changes: l

Feature change Changes in features and parameters of a specified version as well as the affected entities

l

Editorial change Changes in wording or addition of information and any related parameters affected by editorial changes. Editorial change does not specify the affected entities.

01 (2017-03-15) This issue includes the following changes.

Issue 01 (2017-03-15)

Change Type

Change Description

Parameter Change

Feature change

None

None


1


1 About This Document

Change Type

Change Description

Parameter Change

Editorial change

Added hardware planning requirements for DEUa/ EGPUb boards. For details, see 6.3.3 Hardware Planning.

None

Draft A (2016-12-30) This document is created for GBSS19.1.

Issue 01 (2017-03-15)


2


2 Overview

2

Overview

2.1 Introduction As GU refarming is applied more widely, UMTS frequencies cause more severe uplink interference on GSM networks in GU@5MHz scenarios, worsening the GSM uplink voice quality and related KPIs. The Uplink CoMP feature is introduced to improve GSM uplink voice receive quality using the joint reception technique. With this feature, two cells can simultaneously receive uplink voice signals from cell-edge MSs, and the BSC then combines and decodes these signals, reducing the bit error rate (BER) significantly and improving uplink decoding performance. Figure 2-1 Working principles of Uplink CoMP

NOTE

This feature can be used in multi-BTS scenarios but not in multi-BSC scenarios.

2.2 Concepts This document involves the following concepts: Issue 01 (2017-03-15)


3


l

2 Overview

Uplink CoMP MS

An MS using this feature for joint reception l

Host cell

A serving cell accommodating an uplink CoMP MS l

Coordinating cell

A cell receiving additional uplink voice signals from uplink CoMP MSs

2.3 Benefits This feature provides the following benefits for cell-edge MSs when approximately 30% of the traffic is from CoMP calls in the uplink: l l l

The uplink low quality indicator (LQI), the proportion of MRs at receive quality levels 6 and 7 to all MRs in the uplink, decreases by 5% to 20%. The mean opinion score (MOS) increases by 0.1 to 0.2 points. The Abis-interface transmission bandwidth occupied by CS services triples. NOTE

The gains described in this section are all theoretical. There are many factors affecting network performance, and actual gains on the live network may differ from those predicted.

2.4 Architecture Figure 2-2 shows the Uplink CoMP architecture, consisting of algorithm-based decision and combination and decoding. Figure 2-2 Uplink CoMP architecture

Issue 01 (2017-03-15)


4


2 Overview

Table 2-1 Uplink CoMP functions Function Name

Description

Purpose

Algorithm-based decision

This function checks whether to start or stop Uplink CoMP for uplink CoMP MSs based on MRs and selects an appropriate coordinating cell for these MSs.

To identify uplink CoMP MSs for which Uplink CoMP needs to be enabled or disabled and to select an appropriate coordinating cell for these MSs.

Combination and decoding

This function allows the BSC to receive information reported by both the host cell and coordinating cell based on the measurement results reported by the two cells. The measurement information for jointly reception is included in soft information.

To receive signals in both the host cell and coordinating cell.

2.5 Feature Support by NE Table 2-2 NEs supporting the feature Feature Name

BSC6900

BSC6910

GBTS

eGBTS

Uplink CoMP (Joint RX)

√

√

×

√

NOTE

√ indicates that the NE supports this feature. × indicates that the NE does not support this feature.

Issue 01 (2017-03-15)


5


3

3 Technical Description

Technical Description

3.1 Uplink CoMP This feature takes effect when CoMPSwitch(BSC6900,BSC6910) is set to ON(On).

3.1.1 Decision on Starting Uplink CoMP in Connected Mode The BSC selects uplink CoMP MSs and coordinating cells based on after-filtering MRs.

Uplink CoMP MS The BSC considers MS uplink quality to be poor and the MS suitable for an uplink CoMP MS if the filtered uplink quality level of the MS is greater than the value of the CoMPULQualThld(BSC6900,BSC6910) parameter.

Coordinating Cell The BSC can select a coordinating cell based on path loss from synchronized intra-frequency band neighboring cells in the neighboring cell list. 1.

2.

A neighboring cell can be a candidate coordinating cell if both of the following conditions are met: –

(Downlink transmit power of neighboring cell – Filtered downlink signal strength of neighboring cell) < (Downlink transmit power of host cell after power control compensation – Filtered downlink receive level of host cell after power control compensation + Value of CoMPCoCellStartHyst(BSC6900,BSC6910))

–

The neighboring cell meets the P/N criterion for candidate coordinating cells. That is, of N MRs, at least P MRs meet the conditions for determining a candidate coordinating cell.

The BSC sorts candidate coordinating cells in ascending order based on path loss and preferentially selects the cell with the least path loss as the coordinating cell. Path loss of a neighboring cell = Downlink transmit power of the neighboring cell – Filtered downlink signal strength of the neighboring cell If different neighboring cells have the same path loss, the BSC randomly selects one as the coordinating cell.

Issue 01 (2017-03-15)


6



If no coordinating carrier is available in the candidate cell, the BSC reselects a neighboring cell with the second least path loss as the coordinating cell.

3.1.2 Decision on Starting Uplink CoMP During Assignment The BSC selects uplink CoMP MSs and coordinating cells based on SDCCH MRs, and starts Uplink CoMP on the assigned TCH.

NOTICE l This feature cannot be started during TCH assignment. l If the BSC cannot identify the coordinating cell based on SDCCH MRs, this feature cannot be started even when the TCH assignment is complete. Instead, this feature can be started based on TCH MRs. The decision method is the same as that described in 3.1.1 Decision on Starting Uplink CoMP in Connected Mode.

Uplink CoMP MS The BSC considers MS uplink quality to be poor and the MS suitable for an uplink CoMP MS if the filtered uplink quality level of the MS is greater than the value of the CoMPULQualThld(BSC6910,BSC6900) parameter.


A neighboring cell can be a candidate coordinating cell if the following condition is true: (Downlink transmit power of neighboring cell – Filtered downlink signal strength of neighboring cell) < (Downlink transmit power of host cell after power control compensation – Filtered downlink receive level of host cell after power control compensation + Value of CoMPCoCellStartHyst(BSC6900,BSC6910))

2.

The BSC sorts candidate coordinating cells in ascending order based on path loss and preferentially selects the cell with the least path loss as the coordinating cell. Path loss of a neighboring cell = Downlink transmit power of the neighboring cell – Filtered downlink signal strength of the neighboring cell If different neighboring cells have the same path loss, the BSC randomly selects one as the coordinating cell. If no coordinating carrier is available in the candidate cell, the BSC reselects a neighboring cell with the second least path loss as the coordinating cell.

3.

The BSC repeats operations 1 and 2 based on SDCCH MRs and records the coordinating cell for each MR. The coordinating cell selected the last time is considered the final coordinating cell.

3.1.3 Decision on Starting Uplink CoMP During Handover For MSs on which Uplink CoMP has been started, this feature is temporarily stopped during the handover procedure. When the BSC receives the Handover Complete message: Issue 01 (2017-03-15)


7



l

For an inter-cell handover, the BSC considers the host cell before the handover as the coordinating cell and starts this feature again.

l

For an intra-cell handover, the BSC keeps the host cell and coordinating cell unchanged and starts this feature again on other channels of the host cell.

3.1.4 Decision on Coordinating Cell Switch/Stopping of Uplink CoMP The BSC initiates a coordinating cell switch when both the trigger conditions and conditions for determining a coordinating cell are met. The BSC stops Uplink CoMP for uplink CoMP MSs if the trigger conditions are met but the conditions for determining a coordinating cell are not met (the BSC cannot select an available coordinating cell). These conditions are described below.

Trigger Conditions Stopping of this feature will be triggered when the triggering conditions on receive level are met or when the coordinating cell is out of synchronization. A coordinating cell switch is triggered if any of the following conditions is met: l

Quality-triggered An SACCH frame is used as the measurement period. If the average uplink receive BER of the coordinating cell is greater than or equal to the value of CoMPCoCellBERThres(BSC6900,BSC6910), a coordinating cell switch is triggered. Average uplink receive BER of the coordinating cell = (Number of incorrectly decoded bits in an SACCH frame/Total number of bits in the SACCH frame) x 100

l

Level-triggered A coordinating cell switch is triggered if the P/N criterion is met and the following is true: (Downlink transmit power of neighboring cell – Filtered downlink signal strength of neighboring cell) > (Downlink transmit power of host cell after power control compensation – Filtered downlink receive level of host cell after power control compensation + Value of CoMPCoCellStopHyst(BSC6900,BSC6910)) If a coordinating cell switch cannot be performed, stopping of this feature will be triggered.

l

Coordinating cell out of synchronization If the coordinating cell is out of synchronization, the BSC performs a coordinating cell switch. If a coordinating cell switch cannot be performed, stopping of this feature will be triggered.


A neighboring cell can be a candidate coordinating cell if both of the following conditions are met: –

Issue 01 (2017-03-15)

(Downlink transmit power of neighboring cell – Filtered downlink signal strength of neighboring cell) < (Downlink transmit power of host cell after power control compensation – Filtered downlink receive level of host cell after power control compensation + Value of CoMPCoCellStartHyst(BSC6910,BSC6900)) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

8


–

2.


The neighboring cell meets the P/N criterion for candidate coordinating cells. That is, of N MRs, at least P MRs meet the conditions for determining a candidate coordinating cell.

The BSC sorts candidate coordinating cells in ascending order based on path loss and preferentially selects the cell with the least path loss as the coordinating cell. Path loss of a neighboring cell = Downlink transmit power of the neighboring cell – Filtered downlink signal strength of the neighboring cell If different neighboring cells have the same path loss, the BSC randomly selects one as the coordinating cell. If no coordinating carrier is available in the candidate cell, the BSC reselects a neighboring cell with the second least path loss as the coordinating cell.

3.1.5 FACCH Frame Check The BTS evaluates the signal-to-noise ratio (SNR) of the current frame and compares it to the threshold specified by FACCHIdentifyLevel(BSC6900,BSC6910) to check whether the frame is an FACCH frame. l

If it is, Uplink CoMP enhances the frame decoding.

l

If it is not, Uplink CoMP does not enhance the frame decoding.

3.1.6 Combination and Decoding When ULCoMPSoftInfoReportSw(BSC6900,BSC6910) is set to ON(On), the host cell and coordinating cell can report soft information of speech frames, SACCH frames, and FACCH frames to the BSC, where the information can be combined and decoded. When this parameter is set to OFF(Off), the host cell and coordinating cell report soft information of only SACCH frames to the BSC.

3.2 Enhanced Signaling Frame Decoding The enhanced signaling frame decoding function takes effect when SigDecodeEnSwitch(BSC6900,BSC6910) is set to ON(On).

NOTICE This function is not controlled by the license for GBFD-191201 Uplink CoMP (Joint RX).

3.2.1 Enhanced SDCCH Signaling Frame Decoding The MaxSABMCombinedDecode(BSC6900,BSC6910) or MaxSDCCHCombinedDecode(BSC6900,BSC6910) parameter specifies whether the BSC uses this function. l

Issue 01 (2017-03-15)

If MaxSABMCombinedDecode(BSC6900,BSC6910) is set to a value other than 0, the BSC performs combined decoding for SABM frames on the SDCCH for a number of times not exceeding that specified by MaxSABMCombinedDecode(BSC6900,BSC6910), to improve the performance of decoding for SABM frames on the SDCCH. If Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

9



MaxSABMCombinedDecode(BSC6900,BSC6910) is set to 0, the BSC does not perform combined decoding for SABM frames on the SDCCH. l

If MaxSDCCHCombinedDecode(BSC6900,BSC6910) is set to a value other than 0, the BSC performs combined decoding for uplink signaling frames on the SDCCH for a number of times not exceeding that specified by MaxSDCCHCombinedDecode(BSC6900,BSC6910), to improve the performance of decoding for signaling frames on the SDCCH. When MaxSDCCHCombinedDecode(BSC6900,BSC6910) is set to 0, the BSC does not perform combined decoding for signaling frames on the SDCCH.

3.2.2 Enhanced TCH Signaling Frame Decoding This function allows the BSC to perform enhanced decoding for uplink signaling messages in the TCH access and handover phases to improve uplink decoding of signaling frames.

Issue 01 (2017-03-15)


10


4 Related Features

4

Related Features

Prerequisite Features Table 4-1 Features required by Uplink CoMP Feature ID

Feature Name

Description

GBFD-118601

Abis over IP

-

GBFD-118201

Soft-Synchronized Network

GBFD-510401

BTS GPS Synchronization

GBFD-118620

Clock over IP Support 1588V2

GBFD-191201 Uplink CoMP (Joint RX) requires the Soft-Synchronized Network enhancement function of GBFD-118201 Soft-Synchronized Network or the time synchronization function of GBFD-510401 BTS GPS Synchronization or GBFD-118620 Clock over IP Support 1588V2. NOTICE Enabling Soft-Synchronized Network enhancement will preempt resources of coordinating cells for this feature.

The enhanced signaling frame decoding function does not require any features.

Mutually Exclusive Features Table 4-2 Features mutually exclusive with Uplink CoMP

Issue 01 (2017-03-15)

Feature ID

Feature Name/Function Name

Description

GBFD-114001

Extended Cell

-

GBFD-115506

AMR Coding Rate Threshold Adaptive Adjustment


11


4 Related Features

Feature ID

Feature Name/Function Name

Description

GBFD-117501

Enhanced Measurement Report (EMR)

GBFD-117701

BSC Local Switch

GBFD-118701

RAN Sharing

GBFD-118704

Abis Independent Transmission

GBFD-170205

GTMUb SingleOM

N/A

GTMUc SingleOM

GBFD-171216

AMR Transmission Bandwidth Compression

GBFD-510101

Automatic Frequency Correction (AFC)

GBFD-510104

Multi-site Cell

The enhanced signaling frame decoding function is mutually exclusive only with the GBFD-170205 GTMUb SingleOM feature and the GTMUc SingleOM function.

Impacted Features Table 4-3 Impacted features of Uplink CoMP

Issue 01 (2017-03-15)

Feature ID

Feature Name

Description

GBFD-113701

Frequency Hopping (RF hopping, baseband hopping)

GBFD-191201 Uplink CoMP (Joint RX) cannot take effect when inter-PA baseband frequency hopping is enabled.

GBFD-118106

Dynamic Power Sharing

GBFD-191201 Uplink CoMP (Joint RX) cannot take effect when dual-PA power sharing is enabled.

GBFD-114501

Co-BCCH Cell

When this feature and GBFD-191201 Uplink CoMP (Joint RX) are both enabled, Uplink CoMP cannot be performed on an MS if the frequency serving the MS is not in the same frequency band as the BCCH TRX of the coordinating cell.

GBFD-115830

VAMOS

GBFD-160201

VAMOS FR

When this feature and GBFD-191201 Uplink CoMP (Joint RX) are both enabled, VAMOS multiplexing and


12


4 Related Features

Feature ID

Feature Name

Description

GBFD-160217

VAMOS I&II Support

Uplink CoMP cannot be simultaneously performed on the same MSs.

GBFD-115831

Mute SAIC MS Identification

When this feature and GBFD-191201 Uplink CoMP (Joint RX) are both enabled, Uplink CoMP and Mute SAIC MS Identification cannot be simultaneously performed on the same MSs.

GBFD-115832

VAMOS Call Drop Solution

When this feature and GBFD-191201 Uplink CoMP (Joint RX) are both enabled, Uplink CoMP and VAMOS Call Drop Solution cannot be simultaneously performed on the same MSs.

GBFD-115708

Um Interface Speech Frame Repairing

When this feature and GBFD-191201 Uplink CoMP (Joint RX) are both enabled, speech frame repairing remains effective for MSs on which Uplink CoMP is not performed but automatically ceases to be effective for MSs on which Uplink CoMP is performed.

GBFD-117702

BTS Local Switch

When this feature and GBFD-191201 Uplink CoMP (Joint RX) are both enabled, Uplink CoMP and BTS Local Switch cannot be simultaneously performed on the same MSs.

GBFD-119405

14.4kbit/s Circuit Switched Data

GBFD-119406

High Speed Circuit Switched Data

When this feature and GBFD-191201 Uplink CoMP (Joint RX) are both enabled, Uplink CoMP cannot be performed on MSs processing CSD or HSCSD services.

The impacted feature of the enhanced signaling frame decoding function is GBFD-115830 VAMOS. When they are both enabled, VAMOS and repeated transmission and combination of signaling cannot be simultaneously performed on the same MSs.

Issue 01 (2017-03-15)


13


5 Network Impact

5

Network Impact

System Capacity This feature increases the values of the following counters by no more than 5%: l

VS.SCU.CPULOAD.MEAN

l

AVERAGE.USAGE (for a GTC-type DPUc or DPUf board)

l

VS.SUBSYS.CPULOAD.MEAN (for a GUPCS subsystem)

This feature increases the value of the VS.XPU.CPULOAD.MEAN counter (for a XPU board subsystem) by no more than 3%.

Network Performance This feature provides the following benefits for cell-edge MSs when approximately 30% of the traffic is from uplink CoMP calls: l

A 5–20% decrease in the uplink LQI

l

A 0.1–0.2 point improvement in the MOS

l

Tripled Abis-interface transmission bandwidth occupied by CS services

However, this feature increases the voice frame delay by 40 ms.

Issue 01 (2017-03-15)


14


6

6 Engineering Guidelines

Engineering Guidelines

6.1 When to Use Uplink CoMP Use this feature when both of the following conditions are true: l

Uplink LQI > Downlink LQI

l

Uplink LQI > 2%

6.2 Required Information Before deploying this feature, collect the following information of a cell: l

Values of all uplink counters in the MR.RecvLevlOrigFullRate.TRX and MR.RecvLevlOrigHalfRate.TRX function subsets

l

Value of the CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) counter

Check whether the cell is suitable for deployment of this feature based on the collected information.

6.3 Planning 6.3.1 RF Planning l

Each cell supports a maximum of either four carriers (if RRUs or AAUs are used) or three carriers (if RFUs are used).

l

In an area where this feature is enabled, all frequencies serving the MSs in the area must be configured in both the host cell and coordinating cell.

l

A single RF module can be configured with only one cell in a BSC where this feature is enabled.

6.3.2 Network Planning l Issue 01 (2017-03-15)

Do not enable this feature when the inter-site distance is greater than 6 km. Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

15



l

Do not enable this feature in geographically discontinuous areas.

l

In areas where this feature is enabled, time synchronization must be achieved between the host cell and coordinating cell.

l

In areas where this feature is enabled, the Abis-interface transmission bandwidth occupied by CS services will triple. Ensure that the transmission bandwidth meets this requirement before enabling this feature.

l

The Abis interface must use IP transmission.

l

IP transmission over the Abis interface must meet the QoS requirements. For details, see IP BSS Feature Parameter Description.

l

Do not configure the intra-frame bit offset.

l

When this feature is enabled, you are advised to disable real flow access control and perform access control based on the default reserved bandwidth.

l

When this feature is enabled and POUc boards are configured for the BSC6910, do not configure logical ports for the boards, and do not restrict the bandwidth.

6.3.3 Hardware Planning l

When this feature is enabled, the number of required GUEP type DEUa or EGPUb boards is related to traffic volume and board processing capability. –

Number of required DEUa boards = (Value of CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) × 30%/3000) + 1

–

Number of required EGPUb boards = (Value of CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) × 30%/8000) + 1

In the two formulas, the value of CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) indicates the total traffic volume of cells where Uplink CoMP is to be enabled in the BSC, 30% indicates about 30% of users are poor-quality users and they need to use CoMP on common networks, 3,000 indicates the DEUa board processing capability in common voice service scenarios, 8,000 indicates the EGPUb board processing capability in common voice service scenarios, and 1 indicates DEUa or EGPUb boards work in N+1 redundancy mode. l

When this feature is enabled, it is recommended that new GUEP-type DEUa boards be configured in the subrack where the fewest XPU boards are configured, to avoid an inter-subrack traffic burst.

l

When this feature is enabled, it is recommended that new GUEP-type DEUa or EGPUb boards be configured in the same subrack as the Abis interface board, to avoid an intersubrack traffic burst.

Issue 01 (2017-03-15)


16



NOTE

If some DEUa/EGPUb boards are not configured in the same subrack as the Abis interface board, you need to determine the type of SCU board to be used based on the total inter-subrack traffic. l When ULCoMPSoftInfoReportSw(BSC6900,BSC6910) is set to ON(On), the following formula applies: Total inter-subrack traffic = (Value of CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) x 30% x 25 x 9 x 2) + Value of VS.Frame.Flux.Peak.TxRate(BSC6900,BSC6910) l When ULCoMPSoftInfoReportSw(BSC6900,BSC6910) is set to OFF(Off), the following formula applies: Total inter-subrack traffic = (Value of CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) x 30% x 25 x 1 x 2) + Value of VS.Frame.Flux.Peak.TxRate(BSC6900,BSC6910) In these two formulas, the value of CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) indicates the traffic volume of a subrack not configured with any DEUa or EGPUb board, 30% indicates about 30% of users are poor-quality users and they need to use CoMP on common networks, 25 represents the 25 kbit/s of bandwidth required for a call, 9 represents the fact that a CoMP user requires 9 times as much bandwidth as a common user when CoMP soft information is reported, 1 reflects the fact that a CoMP user occupies the same amount of bandwidth as a common user when CoMP soft information is not reported, and 2 reflects the fact that the host cell and coordinating cell each is served by boards in different subracks. When the total inter-subrack traffic is close to or greater than 4 Gbit/s, SCUb boards using 10GE ports or SCUc boards must be configured, and SCUa boards cannot be configured.

l

More Abis interface boards of the same type as the existing Abis interface board are required if the following condition applies to the sites carried on the board: ∑CELL.KPI.TCH.TRAF.ERL.TRAF(BSC6900,BSC6910) × 30% ≥ Maximum number of online users on the board/3 where 30% indicates about 30% of users are poor-quality users and they need to use CoMP on common networks.

6.4 Deployment 6.4.1 Requirements Aspect

Requirement

Related features

See 4 Related Features.

BSC

l BSC6900 The BSC6900 must be configured with DEUa boards. l BSC6910 The BSC6910 must be configured with EGPUb boards.

BTS

l Only eGBTSs whose main control board type is UMPT support this feature. l RF modules are cascaded at a maximum of three levels. l The BTS is configured with any of the following RF modules: RRU3952, RRU3952m, RRU3953, RRU3953w, RRU3959, RRU3959w, RRU3971, AAU3911, AAU3920, MRFU V6, MRFUd V6, and MRFUdw V6

Issue 01 (2017-03-15)


17



Aspect

Requirement

GSM networking

The Abis interface must use IP transmission.

MS

N/A

MSC

N/A

License

The license controlling this feature has been activated. For details about the license control item, see License Control Item Description. For details about how to activate the license, see License Management Feature Parameter Description.

Others

N/A

6.4.2 Precautions None

6.4.3 Hardware Installation For details about how to replace or expand BSC boards, choose Operation and Maintenance > Hardware Management > BSC6900/BSC6910 GSM/GU Site Maintenance Guide > Replacing Boards and Modules in BSC6900/BSC6910 GSM/GU Product Documentation.

6.4.4 Data Preparation and Feature Activation 6.4.4.1 Data Preparation Table 6-1 Parameters in the GCELLBASICPARA MO

Issue 01 (2017-03-15)

Parameter Name

Parameter ID

Setting Notes

Data Source

UL CoMP Switch

CoMPSwitch(BSC6 900,BSC6910)

Determine whether to enable this feature based on suggestions provided in 6.1 When to Use Uplink CoMP. If the feature deployment conditions are met, set this parameter to ON(On). Otherwise, set this parameter to OFF(Off).

Radio network plan (internal plan)


18


Issue 01 (2017-03-15)


Parameter Name

Parameter ID

Setting Notes

Data Source

CoMP Uplink Quality Threshold

CoMPULQualThld( BSC6900,BSC6910)

Use the default value of this parameter if CoMPSwitch(BSC6 900,BSC6910) is set to ON(On).


CoMP Coordinated Cell BER Threshold

CoMPCoCellBERT hres(BSC6900,BSC 6910)



UL CoMP Soft Info Report Switch

ULCoMPSoftInfoR eportSw(BSC6900, BSC6910)

Use the default value of this parameter.


Signaling Frame Decode Switch

SigDecodeEnSwitc h(BSC6900,BSC691 0)

You are advised to set this parameter to ON(On) if cell access-related KPIs (immediate assignment success rate, assignment success rate, and SDCCH call drop rate) are poor.


Maximum SDCCH SABM Frame Combined Decode

MaxSABMCombine dDecode(BSC6900, BSC6910)

Use the default value of this parameter if SigDecodeEnSwitc h(BSC6900,BSC691 0) is set to ON(On).

Default/ Recommended value

Maximum SDCCH Signaling Frame Combined Decode

MaxSDCCHCombi nedDecode(BSC690 0,BSC6910)

Use the default value of this parameter if SigDecodeEnSwitc h(BSC6900,BSC691 0) is set to ON(On).

Default/ Recommended value

FACCH Frame Identification Level

FACCHIdentifyLevel(BSC6900,BSC6 910)




19



Table 6-2 Parameters in the G2GNCELL MO Parameter Name

Parameter ID

Setting Notes

Data Source

CoMP Coordinated Cell Start Hysteresis

CoMPCoCellStartH yst(BSC6900,BSC6 910)



CoMP Coordinated Cell Stop Hysteresis

CoMPCoCellStopH yst(BSC6900,BSC6 910)



CoMP Coordinated Cell Measure Time

CoMPCoCellStatTi me(BSC6900,BSC6 910)



CoMP Coordinated Cell Last Time

CoMPCoCellLastTi me(BSC6900,BSC6 910)



6.4.4.2 Using the CME NOTE

When configuring the Uplink CoMP feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

1.

Configure a single object on the CME. (CME single configuration) Set parameters on the CME according to the operation sequence in Table 6-3. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide.

2.

(Optional) Modify objects in batches on the CME. (CME batch modification center) on the CME to start the batch modification To modify objects in batches, click wizard. For instructions on how to perform a batch modification through the CME batch modification center, press F1 on the wizard interface to obtain online help.

Issue 01 (2017-03-15)


20



Table 6-3 Configuring parameters on the CME SN

MO

NE

Parameter

Configurable in CME Batch Modification Center

1

GCELLBASICPAR A

BSC6900/ BSC6910

See Table 6-1.

Yes

6.4.4.3 Using MML Commands Step 1 Enable the Uplink CoMP feature. On the BSC LMT, run the SET GCELLBASICPARA command with UL CoMP Switch set to ON(On) and other parameters set according to the setting notes provided in Table 6-1. Step 2 (Optional) Enable the signaling frame combination and decoding function. Run the SET GCELLBASICPARA command with Signaling Frame Decode Switch set to ON(On) and other parameters set according to the setting notes provided in Table 6-1. ----End

6.4.4.4 MML Command Examples //Enabling Uplink CoMP: SET GCELLBASICPARA: IDTYPE=BYID, CELLID=0, CoMPSwitch=ON; //(Optional) Enabling signaling frame combination and decoding: SET GCELLBASICPARA: IDTYPE=BYID, CELLID=0, SigDecodeEnSwitch=ON;

6.4.5 Activation Observation l

Uplink CoMP

Step 1 On the BSC LMT, run the SET GCELLBASICPARA command with UL CoMP Switch set to ON(On). Step 2 Observe and record the value of the CALL.CoMP.TRAF(BSC6900,BSC6910) counter for the cell. Expected result: The value calculated in step 2 is greater than 0. ----End l

Enhanced signaling frame decoding

Step 1 Run the SET GCELLBASICPARA command with Signaling Frame Decode Switch set to ON(On). Step 2 Observe and record the values of the CALL.SIG.TCHH.RETRAN.CO.DECODING.SUCC.TIMES(BSC6900,BSC6910) and CALL.TRAF.TCHH.FACCH.RETRAN.CO.SUCC.NUM(BSC6910,BSC6900) counters for the cell. Issue 01 (2017-03-15)


21



Expected result: The value calculated in step 2 is greater than 0. ----End

6.4.6 Deactivation 6.4.6.1 Using the CME NOTE

When configuring the Uplink CoMP feature on the CME, perform a single configuration first, and then perform a batch modification if required. Configure the parameters of a single object before a batch modification. Perform a batch modification before logging out of the parameter setting interface.

1.

Configure a single object on the CME. (CME single configuration) Set parameters on the CME according to the operation sequence in Table 6-4. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide.

2.

Modify objects in batches on the CME. (CME batch modification center) To modify objects, such as BSCs, BTSs, cells, TRXs, and external GSM cells, in icon to start the batch modification wizard. For instructions on batches, click the how to perform a batch modification through the CME batch modification center, press F1 on the wizard interface to obtain online help.

Table 6-4 Configuring the parameter on the CME SN

MO

NE

Parameter

Configurable in CME Batch Modification Center

1

GCELLBASICPAR A

BSC6900/ BSC6910

See Table 6-1.

Yes

6.4.6.2 Using MML Commands Step 1 Disable the Uplink CoMP feature. On the BSC LMT, run the SET GCELLBASICPARA command with UL CoMP Switch set to OFF(Off). Step 2 (Optional) Disable the signaling frame combination and decoding function. Run the SET GCELLBASICPARA command with Signaling Frame Decode Switch set to OFF(Off). ----End

6.4.6.3 MML Command Examples //Disabling Uplink CoMP: SET GCELLBASICPARA: IDTYPE=BYID, CELLID=0, CoMPSwitch=OFF; Issue 01 (2017-03-15)


22



//(Optional) Disabling signaling frame combination and decoding: SET GCELLBASICPARA: IDTYPE=BYID, CELLID=0, SigDecodeEnSwitch=OFF;

6.5 Performance Monitoring Monitor the following items to check the changes after the Uplink CoMP feature is enabled. Item

Description

Expected Result

Uplink LQI

Indicates the proportion of MRs at uplink receive quality levels 6 to 7 to all MRs in the uplink.

Decreased by 5% to 20%

Proportio n of uplink CoMP call traffic

(CALL.CoMP.TRAF(BSC6 900,BSC6910)/ CELL.KPI.TCH.TRAF.ER L.TRAF(BSC6900,BSC6910 )) x 100%

The proportion of uplink CoMP call traffic is about 30%. NOTE A large proportion of uplink CoMP call traffic indicates high LQI gains. A small proportion of uplink CoMP call traffic indicates low LQI gains.

6.6 Parameter Optimization l

Uplink CoMP

When the proportion of uplink CoMP call traffic is lower than the expected value described in 6.5 Performance Monitoring, you can decrease values of the CoMPULQualThld(BSC6900,BSC6910), CoMPCoCellStatTime(BSC6900,BSC6910), and CoMPCoCellLastTime(BSC6900,BSC6910) parameters and increase values of the CoMPCoCellStartHyst(BSC6900,BSC6910) and CoMPCoCellStopHyst(BSC6900,BSC6910) parameters. This helps increase the proportion of uplink CoMP MSs, improving LQI gains. When the Abis interface bandwidth is insufficient, you can set ULCoMPSoftInfoReportSw(BSC6900,BSC6910) to OFF(Off) to reduce the Abis-interface traffic. However, this parameter setting will reduce LQI gains by about 30%. l

Enhanced signaling frame decoding

When the immediate assignment success rate is low and the SDCCH call drop rate is high, you can increase values of MaxSABMCombinedDecode(BSC6900,BSC6910) and MaxSDCCHCombinedDecode(BSC6900,BSC6910) to decrease the SDCCH call drop rate and increase the immediate assignment success rate. When the immediate assignment success rate is high and SDCCH call drop rate increases, you can decrease the value of MaxSABMCombinedDecode(BSC6900,BSC6910) and increase the value of MaxSDCCHCombinedDecode(BSC6900,BSC6910) to decrease the SDCCH call drop rate. However, the immediate assignment success rate will decrease slightly in this case. When the TCH call drop rate increases, you can decrease values of MaxSABMCombinedDecode(BSC6900,BSC6910) and MaxSDCCHCombinedDecode(BSC6900,BSC6910) to decrease the TCH call drop rate. Issue 01 (2017-03-15)


23



6.7 Troubleshooting None

Issue 01 (2017-03-15)


24


7 Parameters

7

Parameters

Table 7-1 Parameters Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CoMPS witch

BSC690 0

SET GCELL BASIC PARA

GBFD-1 91201


Meaning: CoMP function switch. When this parameter is set to ON(On), this function is enabled. When this parameter is set to OFF(Off), this function is disabled. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

CoMPS witch

BSC691 0


GBFD-1 91201


Meaning: CoMP function switch. When this parameter is set to ON(On), this function is enabled. When this parameter is set to OFF(Off), this function is disabled. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

CoMPU LQualT hld

BSC690 0


GBFD-1 91201


Meaning: Threshold used to determine whether to enable CoMP if MS uplink quality is bad. If the filtered uplink quality level of an MS is greater than the value of this parameter, CoMP can be enabled for the MS. GUI Value Range: 0~70 Unit: None Actual Value Range: 0~70 Default Value: 20

Issue 01 (2017-03-15)


25


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CoMPU LQualT hld

BSC691 0


GBFD-1 91201


Meaning: Threshold used to determine whether to enable CoMP if MS uplink quality is bad. If the filtered uplink quality level of an MS is greater than the value of this parameter, CoMP can be enabled for the MS. GUI Value Range: 0~70 Unit: None Actual Value Range: 0~70 Default Value: 20

CoMPC oCellSt artHyst

BSC690 0

ADD G2GNC ELL

GBFD-1 91201

MOD G2GNC ELL


Meaning: Hysteresis used to select a candidate coordinated cell for CoMP. A BSC considers a neighboring cell as a candidate coordinated cell when the following condition is true: Downlink transmit power of the neighboring cell - Filtered downlink signal strength of the neighboring cell < (Downlink transmit power of the serving cell - Filtered downlink receive level of the serving cell after power compensation) + CoMP Coordinated Cell Start Hysteresis. GUI Value Range: 0~63 Unit: dB Actual Value Range: 0~63 Default Value: 40

CoMPC oCellSt artHyst

BSC691 0

ADD G2GNC ELL MOD G2GNC ELL

GBFD-1 91201


Meaning: Hysteresis used to select a candidate coordinated cell for CoMP. A BSC considers a neighboring cell as a candidate coordinated cell when the following condition is true: Downlink transmit power of the neighboring cell - Filtered downlink signal strength of the neighboring cell < (Downlink transmit power of the serving cell - Filtered downlink receive level of the serving cell after power compensation) + CoMP Coordinated Cell Start Hysteresis. GUI Value Range: 0~63 Unit: dB Actual Value Range: 0~63 Default Value: 40

Issue 01 (2017-03-15)


26


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CoMPC oCellBE RThres

BSC690 0


GBFD-1 91201


Meaning: Threshold used to determine whether to trigger a coordinated cell handover. When the uplink bit error rate (BER) of a coordinated cell is greater than or equal to the value of this parameter, the BSC triggers the coordinated cell handover. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 20

CoMPC oCellBE RThres

BSC691 0


GBFD-1 91201


Meaning: Threshold used to determine whether to trigger a coordinated cell handover. When the uplink bit error rate (BER) of a coordinated cell is greater than or equal to the value of this parameter, the BSC triggers the coordinated cell handover. GUI Value Range: 0~100 Unit: % Actual Value Range: 0~100 Default Value: 20

CoMPC oCellSt opHyst

BSC690 0


GBFD-1 91201


Meaning: Whether to disable CoMP for a coordinated cell. A BSC performs a coordinated cell handover or disables CoMP when the following condition is true: Downlink transmit power of the neighboring cell Filtered downlink signal strength of the neighboring cell > (Downlink transmit power of the serving cell Filtered downlink receive level of the serving cell after power compensation) + CoMP Coordinated Cell Stop Hysteresis. GUI Value Range: 0~63 Unit: dB Actual Value Range: 0~63 Default Value: 50

Issue 01 (2017-03-15)


27


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CoMPC oCellSt opHyst

BSC691 0

ADD G2GNC ELL

GBFD-1 91201


Meaning: Whether to disable CoMP for a coordinated cell. A BSC performs a coordinated cell handover or disables CoMP when the following condition is true: Downlink transmit power of the neighboring cell Filtered downlink signal strength of the neighboring cell > (Downlink transmit power of the serving cell Filtered downlink receive level of the serving cell after power compensation) + CoMP Coordinated Cell Stop Hysteresis.

MOD G2GNC ELL

GUI Value Range: 0~63 Unit: dB Actual Value Range: 0~63 Default Value: 50 FACCH Identify Level

BSC690 0


GBFD-1 91201


Meaning: Threshold for a BTS to identify FACCH frames. A large value of this parameter indicates a low probability of identifying FACCH frames. GUI Value Range: 0~10 Unit: None Actual Value Range: 0~10 Default Value: 4

FACCH Identify Level

BSC691 0


GBFD-1 91201


Meaning: Threshold for a BTS to identify FACCH frames. A large value of this parameter indicates a low probability of identifying FACCH frames. GUI Value Range: 0~10 Unit: None Actual Value Range: 0~10 Default Value: 4

ULCoM PSoftIn foRepor tSw

BSC690 0


GBFD-1 91201


Meaning: Switch for controlling whether a BTS reports soft information about frames of all types to a BSC when CoMP is enabled. When this parameter is set to ON(On), the BTS reports soft information about speech frames, FACCH frames, and SACCH frames to the BSC. When this parameter is set to OFF(Off), the BTS reports soft information only about SACCH frames to the BSC. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: ON(On)

Issue 01 (2017-03-15)


28


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

ULCoM PSoftIn foRepor tSw

BSC691 0


GBFD-1 91201


Meaning: Switch for controlling whether a BTS reports soft information about frames of all types to a BSC when CoMP is enabled. When this parameter is set to ON(On), the BTS reports soft information about speech frames, FACCH frames, and SACCH frames to the BSC. When this parameter is set to OFF(Off), the BTS reports soft information only about SACCH frames to the BSC. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: ON(On)

SigDeco deEnSw itch

BSC690 0


GBFD-1 91201


Meaning: Enhanced SDCCH/FACCH frame decoding function switch. When this parameter is set to ON(On), SDCCH and FACCH frames are combined and decoded. When this parameter is set to OFF(Off), this function is disabled. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

SigDeco deEnSw itch

BSC691 0


GBFD-1 91201


Meaning: Enhanced SDCCH/FACCH frame decoding function switch. When this parameter is set to ON(On), SDCCH and FACCH frames are combined and decoded. When this parameter is set to OFF(Off), this function is disabled. GUI Value Range: OFF(Off), ON(On) Unit: None Actual Value Range: OFF, ON Default Value: OFF(Off)

MaxSA BMCo mbined Decode

BSC690 0


GBFD-1 91201


Meaning: Maximum number of times SABM frames can be combined and decoded on the SDCCH. When this parameter is set to 0, SABM frames are not combined or decoded. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 Default Value: 0

Issue 01 (2017-03-15)


29


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

MaxSA BMCo mbined Decode

BSC691 0


GBFD-1 91201


Meaning: Maximum number of times SABM frames can be combined and decoded on the SDCCH. When this parameter is set to 0, SABM frames are not combined or decoded. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 Default Value: 0

MaxSD CCHCo mbined Decode

BSC690 0


GBFD-1 91201


Meaning: Maximum number of times I frames and Rej frames can be combined and decoded on the SDCCH. When this parameter is set to 0, I frames and Rej frames on the SDCCH are not combined or decoded. GUI Value Range: 0~31 Unit: None Actual Value Range: 0~31 Default Value: 1

MaxSD CCHCo mbined Decode

BSC691 0


GBFD-1 91201


Meaning: Maximum number of times I frames and Rej frames can be combined and decoded on the SDCCH. When this parameter is set to 0, I frames and Rej frames on the SDCCH are not combined or decoded. GUI Value Range: 0~31 Unit: None Actual Value Range: 0~31 Default Value: 1

CoMPC oCellSt atTime

BSC690 0


GBFD-1 91201


Meaning: Whether a neighboring cell meets the P/N criterion for enabling CoMP. CoMP request is triggered when P MRs of N MRs meet the CoMP condition. This parameter specifies a value corresponding to N in the P/N criterion. GUI Value Range: 1~16 Unit: 480ms Actual Value Range: 480~7680 Default Value: 6

Issue 01 (2017-03-15)


30


7 Parameters

Parame ter ID

NE

MML Comma nd

Feature ID

Feature Name

Description

CoMPC oCellSt atTime

BSC691 0

ADD G2GNC ELL

GBFD-1 91201


Meaning: Whether a neighboring cell meets the P/N criterion for enabling CoMP. CoMP request is triggered when P MRs of N MRs meet the CoMP condition. This parameter specifies a value corresponding to N in the P/N criterion.

MOD G2GNC ELL

GUI Value Range: 1~16 Unit: 480ms Actual Value Range: 480~7680 Default Value: 6

CoMPC oCellLa stTime

BSC690 0

ADD G2GNC ELL

GBFD-1 91201

MOD G2GNC ELL


Meaning: Whether a neighboring cell meets the P/N criterion for enabling CoMP. CoMP request is triggered when P MRs of N MRs meet the CoMP condition. This parameter specifies a value corresponding to P in the P/N criterion. GUI Value Range: 1~16 Unit: 480ms Actual Value Range: 480~7680 Default Value: 4

CoMPC oCellLa stTime

BSC691 0


GBFD-1 91201


Meaning: Whether a neighboring cell meets the P/N criterion for enabling CoMP. CoMP request is triggered when P MRs of N MRs meet the CoMP condition. This parameter specifies a value corresponding to P in the P/N criterion. GUI Value Range: 1~16 Unit: 480ms Actual Value Range: 480~7680 Default Value: 4

Issue 01 (2017-03-15)


31


8 Counters

8

Counters

Table 8-1 Counters Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1278087438

CELL.KPI.TC H.TRAF.ERL. TRAF

K3014:Traffic Volume on TCH

BSC6900

GBFD-110501

Call Control

1278087438

CELL.KPI.TC H.TRAF.ERL. TRAF

K3014:Traffic Volume on TCH

BSC6910

GBFD-110501

Call Control

1279769419

AVERAGE.US AGE

AR9403:Averag e DSP CPU Usage

BSC6900

GBFD-111705

GSM Flow Control

GBFD-111203

O&M of BSC

1282442485

UP.CoMP.OC CU.CH.MAX. NUM

R0408:Maximu m Number of Channels Occupied by CoMP Calls

BSC6910

GBFD-191201


1282442486

UP.CoMP.OC CU.CH.MIN.N UM

R0409:Minimu m Number of Channels Occupied by CoMP Calls

BSC6910

GBFD-191201


1282442493

VS.DEU.DSP. CoMP.OCCU. CH.MAX.NU M

R0408:Maximu m Number of Channels Occupied by CoMP Calls

BSC6900

GBFD-191201


Issue 01 (2017-03-15)


32


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282442496

VS.DEU.DSP. CoMP.OCCU. CH.MIN.NUM

R0409:Minimu m Number of Channels Occupied by CoMP Calls

BSC6900

GBFD-191201


1282442500

CALL.CoMP. CHAN.USED. NUM

M3208:Number of Channels Used by a CoMP Call

BSC6900

GBFD-191201


1282442500

CALL.CoMP. CHAN.USED. NUM

M3208:Number of Channels Used by a CoMP Call

BSC6910

GBFD-191201


1282442501

CALL.CoMP. TRIG.NUM

M32010:Numbe r of Triggered CoMP Decisions

BSC6900

GBFD-191201


1282442501

CALL.CoMP. TRIG.NUM

M32010:Numbe r of Triggered CoMP Decisions

BSC6910

GBFD-191201


1282442502

CALL.CoMP. REQ.NUM

M32011:Numbe r of CoMP Requests

BSC6900

GBFD-191201


1282442502

CALL.CoMP. REQ.NUM

M32011:Numbe r of CoMP Requests

BSC6910

GBFD-191201


1282442503

CALL.CoMP.S UCC.NUM

M32012:Numbe r of CoMP Successes

BSC6900

GBFD-191201


1282442503

CALL.CoMP.S UCC.NUM

M32012:Numbe r of CoMP Successes

BSC6910

GBFD-191201


1282442504

CALL.CoMP. CO.REQ.NUM

M32013:Numbe r of Coordinated Cell Requests

BSC6900

GBFD-191201


1282442504

CALL.CoMP. CO.REQ.NUM

M32013:Numbe r of Coordinated Cell Requests

BSC6910

GBFD-191201


Issue 01 (2017-03-15)


33


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282442505

CALL.CoMP. CO.CONG.NU M

M32014:Numbe r of Coordinated Cell Congestions

BSC6900

GBFD-191201


1282442505

CALL.CoMP. CO.CONG.NU M

M32014:Numbe r of Coordinated Cell Congestions

BSC6910

GBFD-191201


1282442506

CALL.CoMP. CO.SHO.TRI G.LEVEL.NU M

M32015:Numbe r of Software Handovers Triggered by Level for a Coordinated Cell

BSC6900

GBFD-191201


1282442506

CALL.CoMP. CO.SHO.TRI G.LEVEL.NU M

M32015:Numbe r of Software Handovers Triggered by Level for a Coordinated Cell

BSC6910

GBFD-191201


1282442507

CALL.CoMP. CO.SHO.TRI G.QUAL.NUM

M32016:Numbe r of Software Handovers Triggered by Quality for a Coordinated Cell

BSC6900

GBFD-191201


1282442507

CALL.CoMP. CO.SHO.TRI G.QUAL.NUM

M32016:Numbe r of Software Handovers Triggered by Quality for a Coordinated Cell

BSC6910

GBFD-191201


1282442508

CALL.CoMP. CO.RES.PREE MPTION.TIM ES

M32017:Numbe r of Times Coordinated Cell Resources for CoMP Are Preempted

BSC6900

GBFD-191201


Issue 01 (2017-03-15)


34


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282442508

CALL.CoMP. CO.RES.PREE MPTION.TIM ES

M32017:Numbe r of Times Coordinated Cell Resources for CoMP Are Preempted

BSC6910

GBFD-191201


1282442509

CALL.CoMP. CO.AVAIL.CH .NUM

M32019:Numbe r of Channels Available for Coordinated Cells for CoMP

BSC6900

GBFD-191201


1282442509

CALL.CoMP. CO.AVAIL.CH .NUM

M32019:Numbe r of Channels Available for Coordinated Cells for CoMP

BSC6910

GBFD-191201


1282442510

CALL.CoMP. CO.OCCP.CH. NUM

M32021:Numbe r of Channels Occupied by Coordinated

BSC6900

GBFD-191201


1282442510

CALL.CoMP. CO.OCCP.CH. NUM

M32021:Numbe r of Channels Occupied by Coordinated

BSC6910

GBFD-191201


1282442511

CALL.CoMP.S OURCE.DEC ODE.SUCC.TI MES

M32032:Numbe r of Times Speech Frames of a CoMP Call Are Successfully Decoded by the Source Cell

BSC6900

GBFD-191201


1282442511

CALL.CoMP.S OURCE.DEC ODE.SUCC.TI MES

M32032:Numbe r of Times Speech Frames of a CoMP Call Are Successfully Decoded by the Source Cell

BSC6910

GBFD-191201


Issue 01 (2017-03-15)


35


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282442512

CALL.CoMP. COMB.DECO DE.SUCC.TIM ES

M32022:Numbe r of Times Speech Frames of a CoMP Call Are Successfully Combined and Decoded

BSC6900

GBFD-191201


1282442512

CALL.CoMP. COMB.DECO DE.SUCC.TIM ES

M32022:Numbe r of Times Speech Frames of a CoMP Call Are Successfully Combined and Decoded

BSC6910

GBFD-191201


1282442513

CALL.CoMP. COMB.DECO DE.FAIL.TIM ES

M32023:Numbe r of Times Speech Frames of a CoMP Call Fail to Be Combined and Decoded

BSC6900

GBFD-191201


1282442513

CALL.CoMP. COMB.DECO DE.FAIL.TIM ES

M32023:Numbe r of Times Speech Frames of a CoMP Call Fail to Be Combined and Decoded

BSC6910

GBFD-191201


1282442514

CALL.CoMP.S ACCH.SOUR CE.DECODE. SUCC.TIMES

M32024:Numbe r of Times SACCH Frames of a CoMP Call Are Successfully Decoded by the Source Cell

BSC6900

GBFD-191201


1282442514

CALL.CoMP.S ACCH.SOUR CE.DECODE. SUCC.TIMES

M32024:Numbe r of Times SACCH Frames of a CoMP Call Are Successfully Decoded by the Source Cell

BSC6910

GBFD-191201


Issue 01 (2017-03-15)


36


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282442515

CALL.CoMP.S ACCH.CO.DE CODE.SUCC. TIMES

M32025:Numbe r of Times SACCH Frames of a CoMP Call Are Successfully Combined and Decoded

BSC6900

GBFD-191201


1282442515

CALL.CoMP.S ACCH.CO.DE CODE.SUCC. TIMES

M32025:Numbe r of Times SACCH Frames of a CoMP Call Are Successfully Combined and Decoded

BSC6910

GBFD-191201


1282442516

CALL.CoMP.S ACCH.CO.DE CODE.FAIL.T IMES

M32026:Numbe r of Times SACCH Frames of a CoMP Call Fail to Be Combined and Decoded

BSC6900

GBFD-191201


1282442516

CALL.CoMP.S ACCH.CO.DE CODE.FAIL.T IMES

M32026:Numbe r of Times SACCH Frames of a CoMP Call Fail to Be Combined and Decoded

BSC6910

GBFD-191201


1282442517

CALL.CoMP.F ACCH.SOUR CE.DECODE. SUCC.TIMES

M32027:Numbe r of Times FACCH Frames of a CoMP Call Are Successfully Decoded by the Source Cell

BSC6900

GBFD-191201


1282442517

CALL.CoMP.F ACCH.SOUR CE.DECODE. SUCC.TIMES

M32027:Numbe r of Times FACCH Frames of a CoMP Call Are Successfully Decoded by the Source Cell

BSC6910

GBFD-191201


Issue 01 (2017-03-15)


37


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282442518

CALL.CoMP.F ACCH.CO.DE CODE.SUCC. TIMES

M32028:Numbe r of Times FACCH Frames of a CoMP Call Are Successfully Combined and Decoded

BSC6900

GBFD-191201


1282442518

CALL.CoMP.F ACCH.CO.DE CODE.SUCC. TIMES

M32028:Numbe r of Times FACCH Frames of a CoMP Call Are Successfully Combined and Decoded

BSC6910

GBFD-191201


1282442519

CALL.CoMP.F ACCH.CO.DE CODE.FAIL.T IMES

M32029:Numbe r of Times FACCH Frames of a CoMP Call Fail to Be Combined and Decoded

BSC6900

GBFD-191201


1282442519

CALL.CoMP.F ACCH.CO.DE CODE.FAIL.T IMES

M32029:Numbe r of Times FACCH Frames of a CoMP Call Fail to Be Combined and Decoded

BSC6910

GBFD-191201


1282442520

CALL.SIG.TC HH.RETRAN. CO.DECODIN G.SUCC.TIM ES

M32030:Numbe r of Successful Frame Retransmission, Combining, and Decoding Times on a Signaling Channel

BSC6900

GBFD-191201


1282442520

CALL.SIG.TC HH.RETRAN. CO.DECODIN G.SUCC.TIM ES

M32030:Numbe r of Successful Frame Retransmission, Combining, and Decoding Times on a Signaling Channel

BSC6910

GBFD-191201


Issue 01 (2017-03-15)


38


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282442522

CALL.TRAF.T CHH.FACCH. RETRAN.CO. SUCC.NUM

M32034:Numbe r of Times FACCH Frames Are Successfully Retransmitted and Combined on a Traffic Channel

BSC6900

GBFD-191201


1282442522

CALL.TRAF.T CHH.FACCH. RETRAN.CO. SUCC.NUM

M32034:Numbe r of Times FACCH Frames Are Successfully Retransmitted and Combined on a Traffic Channel

BSC6910

GBFD-191201


1282458471

UP.CoMP.OC CU.CH.MEAN .NUM

R0412:Average Number of Channels Occupied by CoMP Calls

BSC6910

GBFD-191201


1282458472

VS.DEU.DSP. CoMP.OCCU. CH.MEAN.NU M

R0412:Average Number of Channels Occupied by CoMP Calls

BSC6900

GBFD-191201


1282458473

CALL.CoMP. TRAF

M3209:CoMP Call Traffic Volume

BSC6900

GBFD-191201


1282458473

CALL.CoMP. TRAF

M3209:CoMP Call Traffic Volume

BSC6910

GBFD-191201


1282458474

CALL.CoMP. CO.AVAIL.AV G.CH.NUM

M32018:Averag e Number of Channels Available for Coordinated Cells for CoMP

BSC6900

GBFD-191201


Issue 01 (2017-03-15)


39


8 Counters

Counter ID

Counter Name

Counter Description

NE

Feature ID

Feature Name

1282458474

CALL.CoMP. CO.AVAIL.AV G.CH.NUM

M32018:Averag e Number of Channels Available for Coordinated Cells for CoMP

BSC6910

GBFD-191201


1282458476

CALL.CoMP. CO.USED.AV G.CH.NUM

M32020:Averag e Number of Channels Occupied by Coordinated Cells for CoMP

BSC6900

GBFD-191201


1282458476

CALL.CoMP. CO.USED.AV G.CH.NUM

M32020:Averag e Number of Channels Occupied by Coordinated Cells for CoMP

BSC6910

GBFD-191201


67204467

VS.SCU.CPUL OAD.MEAN

AR9730:Averag e CPU Usage of the SCU

BSC6900

GBFD-111705

GSM Flow Control

AR9780:Averag e CPU Usage of the XPU

BSC6900

73415210

VS.XPU.CPUL OAD.MEAN

GBFD-111203

O&M of BSC GBFD-111705 GBFD-111203

GSM Flow Control O&M of BSC

73429073

VS.DEU.DSP. UsagePeak

Maximum DEU DSP Usage

BSC6900

GBFD-191201


73436939

VS.Frame.Flux .Peak.TxRate

HR9732a:Peak Inter-Subrack Transmitting Traffic

BSC6900

MRFD-210104

BSC/RNC Resource Sharing

73436939

VS.Frame.Flux .Peak.TxRate

HR9732a:Peak Inter-Subrack Transmitting Traffic

BSC6910

MRFD-210104

BSC/RNC Resource Sharing

73442003

VS.SUBSYS.C PULOAD.ME AN

AR9725:Averag e Subsys CPU Usage of the Board

BSC6910

GBFD-111705

GSM Flow Control

VS.DEU.DSP. UsageAvg

Average DEU DSP Usage

BSC6900

73445290

Issue 01 (2017-03-15)

GBFD-111203

O&M of BSC GBFD-191201



40


9 Glossary

9

Glossary

For the acronyms, abbreviations, terms, and definitions, see Glossary.

Issue 01 (2017-03-15)


41


10

10 Reference Documents

Reference Documents

None

Issue 01 (2017-03-15)


42

Uplink CoMP (Joint RX)(GBSS19.1_01).pdf

Recommend Documents