Shp-dp920 728 Manual

Safety Cautions

Outer Body Parts Number Pad Unlighted

This section contains important information to ensure the user’s safety and prevent potential damage to property. Please, read this section carefully and use the product accordingly.

Warning

Touch Number Pad

Number Pad Lighted

Fingerprint Reading Panel Open Fingerprint Cover Button

BIOMETRICS

SHP-DP728

BIOMETRICS BIOMETRICS

BIOMETRICS

• The user shall not install or repair the product without authorization. • Do not install the product in the place where the gap between the door and the frame is 5mm or more. • Make sure that no unauthorized person has the access to the password. • Do not operate the product with wet hands, and keep liquids such as water or drinks away from the product, or the product may malfunction or be damaged. • Do not use the excessive force or sharp objects to push the lockbuttons, as this can damage the product. • Make sure that the door is completely closed when going outside. The manufacturer does not assume the responsibility for any harm caused by engagement of the lock on an improperly closed door.

64&3."/6"-

BIOMETRICS

Convenient Opening

Easy push/pull handle access

Welcome Function

When a user gets close to the door lock, the authorization standby mode will automatically activate.

• Please do not hang on the product or pull it. • Long-term exposure to direct sunlight may cause a crack on its touch pad. Avoid exposure to direct sunlight during installation. • During battery replacement, use a new one instead of the existing battery. • Be sure to correctly match the poles (+/-) when installing the batteries. Install the batteries with the correct poles (+/-). • Do not use water, benzene or alcohol when cleaning the product, as these fluids can cause product malfunction. • Replace the batteries within 1 week after the battery replacement alarm sounds. • Interference in wireless communication may occur when this product is used. • According to the wireless communication environment, its battery may consume much.

Card Reader

Proximity Sensor Number Pad Entry Complete/ Silent Mode Switch Button Battery Replacement Time Alert

BIOMETRICS

Away Security Setup

BIOMETRICS

Emergency Alert Light Double Lock Light External Power Contact Part Reset Switch Emergency Keyhole

Inner Body Parts

Product Components

Silent-Mode Function

When going in or out, the sound of the key entering and door opening will be suspended.

The Battery Cover Release Button

The product components used may vary depending on the installation environment.

(After pressing the battery cover release button, pull towards the front, and then the battery cover will open.)

Automatic Card Reading Function

When a card touches the reader, the reader will conveniently recognize the card.

Battery Cover

BIOMETRICS

1.5V AA Batteries

Double Authorization

Requires password & fingerprint combination to open

Security Assurance Function

Sound Control Switch

Mortise Mortise

When someone is inside the house, authorization for entry from the outside will be prohibited.

Strike

(SHS-AML320)

Built-in Wireless Module (Optional) Auto/Manual Locking Switch

Registration Button CLOSE Button

Built-in Fire Detection

Generates alarm in case of a fire

Security Function

Prevents intrusion from the outside

Smartphone Interworking functionG

Outer Body

Conveniently open the door through the Bluetooth function of a smart phone

Mortise Strike (SHS-AML220) box

Strike (For B2C Only)

Key Tag (For B2C Only) (2EA) User Manual, Product Warranty ‘AA’ Batteries (LR6) Emergency Key

www.samsungsds-nss.com/en

Mortise

Strike Strike box

Inner Body

Handle Shaft Spring Handle Shaft, Installation Screws Installation Manual(For B2C Only)

Deadbolt Latch bolt Open-door sensor

GC68-02163A ED:02

2

SHS-AML320

SHS-AML220

Opening the Door from Outside with a Password

Opening the Door from the Inside

Fingerprint, Card and Key Tag Registration

When purchased, the product is set to Multi-leveled Security Code Entry Mode initially. Please refer to “Multi-leveled Security Code Entry Mode setting” for Common Mode setting. ※S ilent Mode

Available in both a push-pull or pull-push Depending on the direction of the door installed in the residence, customer can choose from either push-pull type or pull-push type on purchase.

You can register and use up to 100 fingerprints. Up to 20 cards, including the key tag, can be registered. (Only ISO14443 A Type is available.) 1. Pressing the [Register] Button 2. Entering the Password (from the inside) (from the outside)

Push

Pull

Pull

Push

Before entering the password, press the [] button and enter the password, then both the sound of the key entering and the door opening will be suspended. It is a useful function if you do not want to disturb neighbors when you go in and out at night.

When two arbitrary buttons are lighted, press the buttons in order.

When the numbers on the number pad are lighted, enter the password and press the [] button.

- If the security mode is changed as ‘common mode’, second step will be skipped. ● Password must be entered after the light is on, and if does not, touch [Number Pad] and re-enter. ● To cancel, press [ ] button and re-enter. ● If the password is wrong 5 times, “peep” warning alarm will sound 20 times and the system will shut-down for about 3 minutes. When malfunction happens, “beep” will sound every 10 seconds, and stop mode will be turned off automatically after 3 minutes with multiple ‘beeps’.

Note

Open the battery cover of the inner body and briefly press the [Register] button.

Closing the Door from the Inside Automatic Locking Setting Manual Locking Setting

Note

Open the door from the outside using the fingerprint authentication system. Touch the sensor properly with the fingerprint part of your finger which has been registered. 1. Pressing [Open Fingerprint Cover] Button

3. Reading the Fingerprint to Be Registered

The door is locked when the [Close] button is pressed.

Success: DING DONG DENG DONG Fail: DING DONG DING DONG

BIOMETRICS

Press the [Open Fingerprint Cover] button and the lid of the Fingerprint Reading Panel opens.

Press and hold the [Register] button for 5 seconds.

Touch the Fingerprint Reading Panel with the registered fingerprint after LED light turns on, the lid of the panel closes in approximately a second later. Then push the door handle to open the door.

Opening the Door from Outside with a Card or Key Tag

[Card and Key Tag Registration] 3. Placing the Card or Key Tag on the Card Reader (from the outside)

Success: DING DONG DENG Fail: DING DONG DING DONG When the number pad is lighted, enter ‘4560852580’ and then press the [] button.

CARD

Place the card or key tag to be registered on the card reader of the outer body. You will know the card or key tag has been registered when “DING DONG DENG” sounds.

Place the registered card or key tag to the card reader on the outer body.

● To register multiple cards or key tags, lightly place another card or key tag to the card reader within 20 seconds after registering the previous card or key tag. Warning

Pairing of a smart phone Up to eight compatible smart phones can be paired. To pair multiple smart phones, turn off the Bluetooth of a paired smart phone, and pair another smart phone. If a Bluetooth smart phone registered is lost, replaced, or repaired and its information cannot be deleted from the door lock, the door lock should be initialized.

DING DONG

RD

RD CA RD CA

CA

Placing the Card or Key Tag on the Card Reader

RD

CA

4

4. Confirming Card or Key Tag Registration (from the outside)

DING DONG DENG

CARD

DING DONG DENG [11] button: Activate the Bluetooth mode. [00] button: Deactivate the Bluetooth mode.

Place the card or key tag on the card reader. The door will be opened after 1 second.

To end the registration, please press the [Registration] button on the inner body.

After the Bluetooth mode is activated, accessing the door lock from the outside or touching its number pad can authenticate the registered Bluetooth smartphone to open the door. The Bluetooth mode is activated by default.

The door can be opened from outside using a card or key tag. Place the registered card or key tag on the card reader.

BIOMETRICS

DING DONG DENG

Activation/Deactivation of the Bluetooth Mode

BIOMETRICS BIOMETRICS


When LED light on the Fingerprint Reading Panel is on, touch the panel with the fingerprint to be registered. When a “ding” sound is heard and LED light goes off, then remove the finger. (Must do it 3 times)

All registered data (password, Fingerprint, Bluetooth, card, key tag) are deleted. After initialization, the password is set to ‘1234’, and the registered card, key tag data are erased. Please register a new password after initialization. 1. Pressing the [Register] Button 2. Entering the Numbers for (from the inside) Initialization (from the outside) DING DONG  DING DING  DING DING DING DING

4. Exiting Fingerprint Registration Mode

Success: DING DONG DENG Fail: DING DONG DING DONG

DING

● To check if the door is locked from the inside, press the security button briefly; the red LED will flash if the door is locked and the blue LED will blink if the door is unlocked. ● For 5 seconds after the door is closed, the Bluetooth authentication mode is not turned on even though you approach the door lock. (Note that the Bluetooth mode is turned on when you touch the number pad.)

Initialization (Password, Fingerprint, Bluetooth, Card, Key Tag)

2. Reading Fingerprint

Enter the password (‘1234’ after initialization) when the number pad is lighted, and press the [] button.

[Fingerprint Registration]

The door is automatically locked 1 seconds after the door is closed.

GC68-02162A ED01

Opening the Door from the Outside with a Fingerprint

BIOMETRICS

● Please be careful not to trap your Warning hand during use.

Or Success: DING DONG DENG DONG Fail: DING DONG DING DONG

Touching [Number Pad] will light up the number pad.

DING DONG DENG, DING DING

DING DONG

Multi-leveled Security Code Entry Mode

3

Open the battery cover, and press the [Register] button shortly.

Note

Press the [11] or [00] button and the [] button to activate or deactivate the Bluetooth mode.

● For the information on the pair/unfair of a Bluetooth smart phone, see the description of application use. ●Only smart phones with iOS 7.1 or higher and Android 4.3 or higher support this function. Whether to support Bluetooth, see the App description.

DING DONG

Download “sHome Doorlock” from App Store.

Turn on the BlueOpen the battery If the number pad tooth smart phone. cover and press the lights, enter ‘88’ and [REG] button shortly. press the [] button.

Success: DING DONG DENG  DING DONG Fail: DING DONG DING DONG

5

DING DONG

Enter the password and press the [] button.


Enter the 6-digit paring code displayed in the App of the phone, and press the [] button.

The smart phone is paired.

6

Deleting Registered Fingerprints & Cards

Double Authorization Mode Setting

Set up Instructions for Alarm and Anti unlock functions

You can delete individual or all registered fingerprints and cards. 1. Pressing the [Register] Button 2. Entering the Current Password (from the inside) (from the outside)

You can delete Double authorization mode requires both fingerprint and password to open the door, ensuring more security. To setup the double authorization mode, one or more fingerprints must be registered.

Alarm function When this function is activated, an alarm sound and light will turn on for approximately 5 minutes duration.

DING DONG DING DING

DING DONG DENG DING DONG DENG

DING DONG

Open the battery cover of the inner body and briefly press the [Register] button for 3 seconds.

Enter the current password when the number pad is lighted, and press [] button.

[Deleting Fingerprints] 3. Reading the Fingerprint to Be Deleted

4. Exiting Fingerprint Deletion Mode


DING

When LED light on the Fingerprint Reading Panel is on, touch the panel with the fingerprint to be deleted.

[Deleting All Fingerprints] 3. Entering the number (from the outside)

[4] Button : Double authorization mode on [6] Button : Double authorization mode off

Briefly press the [Register] button on the inner body.

Anti-Bypass function When this function is activated, the internal handle will become tightened to prevent bypass attempts through door edge tools will be minimized. Set up the Alarm function

Press the [] button after pressing the [4] or [6] button, and the authorization mode will be set.

Set up the Anti-Unlock function

DING DONG DENG

DING DONG DENG

Two-factor Authentication Mode Operation DING DONG DENG

To end the deletion mode, press [Registration] button.

[Deleting All Cards] 3. Entering the number (from the outside)

DING DONG DENG



Touching [Number Pad].

Enter the password when the number pad is lighted, and press the [] button.

Touch a registered fingerprint on the Fingerprint Reading Panel. After a successful authentication, the door opens.

When the door is closed, user can set up the alarm function by pressing and holding the [ ] button for 3 seconds until sound confirmation.

Press [] and hold. After 3 seconds, the alarm will be come active.

Release the Alarm function

Release the Anti-Bypass function

BEEP BEEP BEEP~

Or

DING DONG DENG

Password Change The password can be 4~12 digits number. Only one password can be registered. If you want to delete all fingerprints, press [77] + [] after step2.

If you want to delete all cards, press [88] + [] after step 2.

1. Pressing the [Register] Button (from the inside)

Security Assurance Mode Activation/Deactivation

2. Entering the Current Password (from the outside) DING DONG DENG, DING DING

DING DONG

At-home security mode is to prevent opening of the door from outside while someone is inside. Security Assurance Mode Activation

● Anti-Bypass function should only be set up when there is no one inside.

DING DONG DENG DONG

While the door is locked, press [CLOSE] button on the inner body part for 3 seconds.

Pull the inner body handle to open the door, and it will deactivate.


Enter the current password (‘1234’ after initialization) when the number pad is lighted, and press the [] button.

3. Entering a New Password (from the outside)

4. Checking New Password Operation (from the outside)

DING DING DENG

DING DONG DENG DONG

Sound Setting and Releasing The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unlocked, can be set according to the user’s preference. The product is set to generate all sounds at the factory. Open the battery cover on the inner body.

Security Assurance Mode Operation Or

Rapid beeping

Press the [CLOSE] button to release the internal handle from Anti-Bypass function. When this function is active, it may be harder to pull the internal handle for elderly or children to open the door from inside.

Warning

Security Assurance Mode Deactivation

DING DONG DENG

After touching the Number Pad, have a registered fingerprint read, or contact a registered card, or enter the password and then press the [] button.

Inside: Press the [CLOSE] button, then the sound for action-unavailable willbe heard. Outside: Press the [Number Pad] or touch with a card, then the sound for action-unavailable will be heard.

●W hen the security assurance function is activated, the door cannot be unlocked from the outside, so please be careful. Be especially careful not to allow children to set this mode accidently from the inside. Warning

Enter the new password (4 to 12 digits) and press the [] button.

To make sure the password has been properly registered, check the new password and close the door.

●M anage your password with care so that unauthorized people will not have access to it. Regularly changing your password can reduce the risk of it being leaked. Warning

7

Put the [Sound Control] switch on one of [0], [1], or [2], and close the battery cover.

- [ 0 ] Button: All sounds except the alarm sound are deactivated. - [1] and [2] Buttons: All sounds are activated and the sounds get bigger as the step become higher.

8

9

Welcome Function On/Off

Automatic/Manual Locking Setting

Alarm Sound (Prank Prevention Function)

The welcome function is a convenient function that automatically activates the authorization standby mode when a user approaches the door, even before touching the number pad.

The Automatic Locking mode allows for automatic locking of the door when it is closed.

This function generates an alarm sound and deactivates lock operation when it is improperly handled from the outside.

DING DONG

Open the battery cover and press [Registration] button briefly.

On and Off / Function Description

Open the battery cover on the inner body.

DING DONG DENG

[1]+[] button: Welcome function on, the oneminute alarm function on [2]+[] button: Welcome function on, the oneminute alarm function off [3]+[] button: Welcome function off [5]+[] button: Set up fingerprint Authentication standby mode [8]+[] button: Clear Fingerprint Authentication standby mode

- Welcome function on: The mode will automatically activate the authorization standby mode when a user approaches the door lock. - Welcome function off: The mode will authorize a user when the user enters the password on the number pad or connects a card to the number pad. - One-minute alarm function on/ off: When someone remains in front of the door lock for more than a minute, this mode will sound the tamper prevention alarm.

Caution

- Automatic: The door is automatically locked 1 seconds after being closed. - Manual: The door does not lock automatically, and [CLOSE] button must be pressed from the inside, touch [Number Pad] to close the door.

Intrusion Detection Function This function generates the alarm sound when an attempt is made to forcefully open the door from the inside or the outside. (This is a basic function of the lock, and cannot be separately set or released.) If the door is forcefully opened while locked, the door opening sensor detects it and generates the alarm sound.

Battery Replacement Alarm Generation

Replacing the Battery Replace all 8 batteries within a 1 week of the first alarm sound. - The unit will stop operating suddenly if the batteries are not replaced.

DING DONG DENG [7] Button : Multi-leveled Security Code Entry Mode [9] Button : Common Mode

Briefly press the [Register] button on the inner body.

Press the [] button after pressing the [7] or [9] button, and the security mode will be set.

Door Lock Time Setup Function This function sets the time interval between the moment the door open/closed sensor recognizes the door as closed and the moment deadbolt locks the door. In an environment that the door closes slowly and the deadbolt jams before the door is fully closed, the situation can be fixed by adjusting the door lock time. DING DONG

Default: 1 second [51] : 1 second

Press [51] ~ [59] button, and then press [] button.

10

Press the [Register] button.

Outside

Apply the registered card or key tag to the card reader, or enter the password and then press the [] button.

Built-in Fire Detection Function This function generates the alarm sound when fire is detected so that the residence can quickly respond. The built-in fire detection function is a basic function of the lock, and cannot be released by the user. Fire detection function is operational at about 70 °C ± 10 °C; this can vary depending on the installation environment.

Product Specifications Item Voltage

Using the Emergency Battery

Operation Method

Electronic Control Method (Password, Fingerprint, Bluetooth, Card, Key Tag)

Product Dimensions

Purchase an emergency battery (9V) at the nearest store. - As the alkaline batteries offer longer life, they are recommended over the manganese batteries or rechargeable ones.

11

AA Alkaline 1.5 Batteries (LR6) 4EA or 8EA (6V) 9V Battery (6LF22) (Separately sold)

Weight

Opening the Door Using an Emergency Battery

Specifications

Emergency Power Source

If the batteries are not replaced after their replacement time comes, they will be completely discharged and the lock will not operate.

While connecting a 9V battery to the contact point, it is available to use fingerprint, card and password.

[59] : 9 second


● Depending on battery manufacturer, date of manufacture and the user environment, the duration of use may vary. (In the case of average use, given as 10 times a day, 8 AA alkaline 1.5Vbatteries can last for 10 months.) ● If the poles of the batteries are not placed properly, the lock will not operate normally. ● Liquid leaks from batteries can damage the product. Check the batteries regularly (every 6 months). ● After the battery replacement alarm has sounded, password/card information cannot be registered, changed, deleted, initialized or configured until the batteries are replaced. ~

Warning

You can set the security mode suitable for your use when you open the door using a password.

Inside

When fire occurs, the temperature sensor detects it and flashes the [Close] button while generating the alarm sound. The door is automatically opened after the alarm sound has stopped. (The lock resumes normal operation if the inside temperature returns to a normal level.) The built-in fire detection function is activated when the temperature rises around 60°C, which may differ depending on the installation environment.

If the melody of “Blues for Elise” sounds when opening the door with the password or a card (key tag), it is time to replace the batteries. (The low battery indicator is lighted when the melody sounds.)

Multi-leveled Security Code Entry Mode

This alarm will sound if an attempt is made to open the door with an invalid card, or if a wrong password is entered five times in a row. The alarm sound is generated, and the lock is deactivated for 3 minutes. While the door is in this inactive mode, a single “DING” sound is generated every 10 seconds and seven consecutive “DINGS” will sound after 3 minutes. Following this, the lock is released from inactive mode.)

Releasing the Alarm

Replacing the Batteries

●The factory defaults are set with the welcome function on and the alarm function off. ● The working distance of the infrared sensor can differ depending on light conditions and other environments. When the front door is exposed to sun light or constant bright lights it is advised to limit the usage of the sensor as it might sound the alarm.

DING DONG

Set the [Automatic/Manual Locking] toggle switch of the Inner Body to the ‘A’/‘M’ position.

4.1 kg (including both inner and outer bodies) Outer Body (including the handle)

87.5mm(W) X 391.8mm(H) X 64.5mm(D)

Inner Body (including the handle)

88.5mm (W) X 357.6mm(H) X 69.3mm(D)

● T he contents of this user guide are subject to change without prior notice to the user in order to enhance performance of the product.

12

SHP-DP920 Samsung SDS Door Lock User and Reference Guide

Ver1.0.0

 Product Specifications Item

Spec.

Exterior Unit

87.5mm(W)×391.8mm(H)×64.5mm(D)

Interior Unit

88.5mm(W)×357.6mm(H)×69.3mm(D)

Size Voltage Emergency Power Source Battery Life Support Card Standard

 Exterior Parts

4 AA Alkaline 1.5V Batteries (LR6) (6V) 9V Battery(6LF22)

(Separately sold)

10 Months (based on an average of 6 uses per day) ISO14443A (Mifare® )

 Interior Parts

 Mortise

The Samsung SDS Z-Wave Door Lock is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enable Z-Wave Plus products. The Samsung SDS Z-Wave Door Lock must be used in conjunction with a Security Enabled Z-Wave Controller in other to fully utilize all implemented functions. The Samsung SDS Z-Wave Door Lock can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

Z-Wave Specifications 

Device Type

:

Door Lock – Keypad (SPECIFIC_TYPE_SECURE_KEYPAD_DOOR_LOCK)



Role Type

:

LSS (Listening Sleeping Slave)



Command Class Support/Control

Mandatory CC support : 

Z-Wave plus info (MUST be place first in NIF) – (V2)



Manufacturer Specific (V2)



Security (V1)



Device Reset Locally (V1)



Battery (V1)



Power Level (V1)



Version (V2)



Door Lock (V2)



User Code (V1)



Association (V2)



Association Group Information (V1)

Recommended CC support 

Notification (V4)



Configuration (V1)



Firmware update meta data (V2)



Schedule Entry Lock (V3)



Time Parameters (V1)



Time (V2)









Z-Wave plus info (V2) -

Z-Wave Plus Version : 02

-

Role Type : LSS (Listening Sleeping Slave)

-

Node Type : Z-Wave Plus Node

Manufacturer Specific (V2) -

Device ID Type : 01(Serial Number)

-

Device ID Data Format : 01 (Binary)

-

Device ID Data Length Indicator : 16

-

Device ID : XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX

Version (V2) -

Z-Wave Protocol Library Type : 03

-

Z-Wave Protocol Version : 04

-

Z-Wave Protocol Sub Version : 05

-

Firmware 0 Version : 01

-

Firmware 0 Sub Version : 03

-

Hardware Version : 01

Door Lock (V2) -

support Unsecure(0x00), Secure(0xFF) Note : When using ‘Operation_Set’ command, lock will execute ‘Unsecure(0x00)’ then perform ‘Auto Re-lock’ if door is not open. When using ‘Operation_Get’ command, lock ‘Operation_Set’ command. (take about 2 seconds)



can

response

after

executing

User Code (V1) -

Lock will accept maximum 130 pin codes that are 4-10 digits in length. ① Supported Users : 130 ② User Type : Number, Card (Key Tag), Fingerprint, Bluetooth ⋅ Card (Key Tag), Fingerprint, Bluetooth : Cannot be registered through Z-Wave ③ ID Range ⋅ Number : 1 ~ 130

⋅ Card (Key Tag) : 1 ~ 20 ⋅ Bluetooth : 21 ~ 30 ⋅ Fingerprint : 31 ~ 130 

Association (V2) & Association Group Information (V1) -

Lifeline between controller and SHP-DP920

-

Supported command classes : Battery report, Notification report, and Device Reset Locally notification



Maximum supported node is 1EA

Notification (V4) Notification Type

Event

Access Control

Manual Lock Operation (0x01)

(0x06)

Manual Unlock Operation (0x02)

Event Parameter

RF Lock Operation (0x03) RF Unlock Operation (0x04) Keypad Unlock Operation (0x06) RF Not Fully Locked Operation (0x08) Auto Lock Loced Operation (0x09) Auto Lock Not Fully Operation (0x0A) Lock Jammed (0x0B) All user codes deleted (0x0C) Single user code deleted (0x0D) New user code added (0x0E) New user code not added due to duplicate code (0x0F) New Program code Entered - Unique code for lock configuration (0x12) Home Security (0x07)

Intrusion, Unkown Location (0x02) Tampering, Invalid Code (0x04)

User ID

Motion Detection, Unknown Location (0x08) Emergency

Contact Police (0x01)

(0x0A)

Contact Fire Service (0x02)



Configuration (V1)

Name

Parameter Number

Size

Value

Description

Security Function

0x01

1byte

0x00

Disable (Default)

0x01

Enable

0x02

System Disable

0x03

System Enable

0x04

Request for Enable

0x05

Fail

0x00

Disable (Default)

0x01

Enable

Privacy Mode

0x02

1byte

1)

1)

1)

1)

Registered User ID

0x03

1byte

1 ~130

The number of registered user codes.

Platform

0x0A

1byte

0x00

Common (Default)

0x01

Samsung SDS

1)

2)

3)

This value can be used when the device is connected with platform of Samsung SDS. This function is not related to Z-Wave CC. - 0x02 : Command for disable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function , '0x00' will be reported. - 0x03 : Command for enable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function, '0x01' will be reported. - 0x04 : 'Request for Enable' command which is reported by Doorlock. This cannot be set. (8th function in manual) - 0x05 : If the request for 'Request for Enable' command is failed in platform, this will be set by platform of Samsung SDS.

Value of Security Function is not changed by this command. 2)

This parameter is supported to ‘Configuration Get Command’ only.

3)

This value set by platform after device connected with platform of Samsung SDS.



Firmware update meta data (V2) -



Manufacturer ID : 0x022E (Samsung SDS)

Schedule Entry Lock (V3) -

Supported the Number of Slots Week Day : 0

-

Supported the Number of Slots Year Day : 0

-

Supported the Number of Slots Daily Repeating : 130

Glossary Devices and nodes are all terms to describe an individual Z-Wave device. These

Device or Node

Unsecure Unsecured

are all interchangeable when setting up your Z-Wave network /

Unlock / Unlocked

Secure / Secured

Lock / Locked

Inclusion

Add a Z-Wave device to the network

Exclusion

Delete a Z-Wave device from the network A collection of Z-Wave devices is controlled by primary and secondary controllers

Z-Wave Network

operating on the same system. A Z-Wave network has its own unique ID code so that controllers not in the network cannot control the system. Association is used to organize nodes in different groups allowing the device to

Association

identify the nodes by a group identifier. The groups can also be copied to other devices.

Note : Pressing the [REG] button is only available while the door is open. (Deadbolt must be unsecured.)

 Basic Functions

1. Factory Reset All registered Master/User data will be deleted, and Master PIN Code is set to ‘1234’. Also ZWave Door Lock is being removed from a network. ①

Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)

②

Press the [*] button after pressing the [4560852580] button. (Success : Ding dong dang, Fail : Ding dong Ding dong)

※ Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

2. Changing the Master PIN Code You can enter only one Master PIN Code. If changing the Master PIN code, All User PIN Codes are deleted. ①

Press the [REG] button. (Ding dong)

②

Enter the new Master PIN Code, and press the [*] button.(4~12digits) (Ding dong dang)

3. Registering a User Card You can register up to 20 User Card. (Supproted ISO14443 A Type) To register multiple cards, lightly place another card to the card reader within 20 seconds after registering the previous card. Also you can add card later after completing registration. ①


②

Place the card to be registered on the card reader of the exterior body.(Ding dong dang)

③

Place the card on the card reader for the addtional registration or press the [REG] button to quit.

4. Registering a Fingerprint You can register up to 100 fingerprints. ①


②

When LED light on the Fingerprint Reading Panel is on, touch the panel with the fingerprint to be registered. When a “ding” sound is heard and LED light goes off, then remove the finger. (Must do it 3 times)

③

To end the registration, please press the [REG] button on the inner body.

5. Registering a Bluetooth ①


②

Enter the [88] + [*]

③

Enter the Password + [*] (Ding dong deng → Ding ding)

④

Check a pairing number from Smart Door Lock App of smartphone.

(Ding dong)

(First, please install the Smart Door Lock app in the smart phone.) ⑤

Enter a Pairing number + [*] (Ding dong deng)

6. Inclusion / Exclusion into(from) Z-Wave Network 6.1 Inclusion into Z-Wave Network ①

Click [Add] icon in Z-Wave PC Conroller Program.

②


③

Press the [*] button after pressing the [00] button. (Success : Ding dong dang, Fail : Ding dong Ding dong)

6.2 Exclusion from Z-Wave Network After exclusion from Z-Wave Netwokr, it will no longer be remotely-controlled via the controller. ①

Click [Remove] icon in Z-Wave PC Conroller Program.

②


③

Press the [*] button after pressing the [00] button.

(Success : Ding dong dang, Fail : Ding dong Ding dong)

7. Opening the Door with a PIN Code ①

Touch the [Touchscreen].

②

Enter the PIN Code and press the [*] button.

③

The door opens whithin one second.

8. Opening the Door with a Card ①

Place the Card on the Card Reader.

②

The door opens whithin one second.

9. Opening the Door with a Fingerprint ①

Press the [Open Fingerprint Cover] button and the lid of the Fingerprint Reading Panel opens.

②

Touch the Fingerprint Reading Panel with the registered fingerprint after LED light turns on, the lid of the panel closes in approximately a second later.

③

Then push the door handle to open the door.

10. Opening the Door with a Bluetooth ①

Access the door lock from the outside or touch its number pad.

②

The number pad will light up.

③

Push message is sent to smartphone through Bluetooth.

④

Press the icon of push message (from smartphone)

⑤

Then push the door handle to open the door.

 Addtional Function

11. Activation/Deactivation of the Bluetooth Mode After the Bluetooth mode is activated, accessing the door lock from the outside or touching its number pad can authenticate the registered Bluetooth smartphone to open the door. The Bluetooth mode is activated by default. ①

Open the battery cover, and press the [REG] button shortly..

②

Press the [11] or [00] button and the [*] button to activate or deactivate the Bluetooth mode. [11] button: Activate the Bluetooth mode. [00] button: Deactivate the Bluetooth mode.

12. Privacy Mode Function Press and hold the [CLOSE] button for more than three seconds. (Ding dong dang) As it is set from the inside, provides a secure lock for the convenience of the occupant(s). When the privacy mode function is activated, the door cannot be unlocked(unsecured) from the outside, so please be careful.

13. Setting the Security Function This is a function to prevent any intrusion while you are out. Should the door be opend from the inside while the intrusion prevention function is on, the emergency alert light will flash and the alarm will make “beep beep beep~” sound. ①

When the door is closed [

②

Press the [

] of the exterior body’s number pad will light up.

] button on the exterior body within 3 seconds while the door is locked.

(Ding dong dang)

14. Lockout Mode When more than 5 failed authentication attempts with unregistered PIN Code/Cards occur, the alarm sound is generated, and the lock is deactivated for 3 minutes.

15. Intrusion Detection Function When the Interior Unit is forcibly detached while the door is locked, it is detected by the door open/close sensor, the alarm sounds. The Intrution Detection function is a basic function and cannot be disabled.

16. Sound Setting The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unloced, can be set according to the user’s preference. Put the [Sound Control] switch on one of [0], [1] or [2]. [0] : Mute

[1] : Normal

[2] : Loud

17. Addtional Function Mode

Shp-dp920 728 Manual

Recommend Documents