Dictionary/Glossary Pulp and Paper “
Word A4 (size) Abaca ABCD Scheme
Abhesive Abrasion Resistance Abrasive Papers
Absolute Humidity
Absolute Viscosity Absolute White
”
Meaning A common ISO A-size of about 8 ¼ by 11 ¾ inches or 210 x 297mm. A fiber also known as manila mani la hemp or manila fiber, prepared from the outer sheath of the stems of manila. An initiative in the UK designed to classify the type and amount of Recycled Fiber in a paper product. The scheme grades four types of waste used in paper manufacturing, as follows: A - Woodfree, approved own mill waste (waste that has not left the mill. i.e. mill broke) . B - Woodfree unprinted waste (waste that has left the mill but not reached the consumer, typically from the printer or converter). C - Woodfree printed waste (post consumer waste, collected from homes, offices etc). D - Printed mechanical waste (post consumer waste, typically newspapers). To be classified as recycled, the grade has to contain no less than 50% of the total fiber from any combination of the above sources, with the percentages given for each.. A material that resists adhesion. Abhesive coatings are applied to surfaces to prevent sticking, etc. The extent to which paper can withstand continuous con tinuous scuffing or rubbing. Papers covered on one or both sides with abrasive powder, e.g. emery, sandpaper etc.
The actual weight of water vapor contained in a unit weight of air, expressed in grams per cubic meter in metric system and pounds per cubic feet in English system. A characteristic of one-component liquids which have a constant ratio of shear stress over shear rate (constant viscosity) In theory a material that perfectly reflects all light energy at every visible wavelength; in practice a solid white with known spectral data that is used as the "reference white" for all measurements of absolute reflectance. (When calibrating a spectrophotometer, often a white ceramic plaque is measured and used as the absolute white reference). Page 1 of 88
Absorbency Absorbent Core
Absorbent Paper
Accept Acetate Fiber
The extent to which a paper will take up and hold a liquid. The principal fluid-holding component of disposable hygiene products. Absorbent cores usually contain a combination of absorbent cellulose fibers (fluff pulps) and super-absorbent polymers composed of polyacrylates. Advanced cores can contain very specialized absorbent absorbent cellulose cellulose fibers, synthetic fibers and super-absorbent polymers as well as fluff pulps. Papers having the specific characteristic of absorbing liquids such as water and ink. These papers are soft, loosely felted, unsized and bulky e.g. blotting paper. Accepted portion of pulp after cleaning and or screening operation. A manufactured fiber in which the fiber-forming substance is cellulose acetate (US Federal Trade Commission (FTC) definition). Acetate fibers are derived by treating pure cellulose, which has been extracted from vegetable matter and generally wood pulp or cotton linters, with acetic anhydride. The resulting product is dissolved in acetone and extruded into filaments and the acetone evaporated. Acetate fibers are moderately strong, generally soft and lustrous like rayon. Acetate staple and filament fibers are more commonly used in weaving operations supplying endmarkets such as lingerie, blouses, dresses, men’s ties and other apparel.
Acetate Pulp
Accelerated Aging
Accordion Fold
Achromatic Acid Detergent Fiber (ADF) Acid Free Paper
Acid Hydrolysis
Acid Migration
A highly purified (high alpha cellulose) pulp made especially to be dissolved in acetic acid, acetic anhydride and sulfuric acid to make acetate rayon and acetate fiber. Exposing paper at elevated temperature usually at 110o C in an oven or on a hot plate. The purpose of accelerated aging is to simulate the effect of aging in the laboratory. A term for two or more parallel folds that result in the sheet opening like a fan. Accordion folds are used on products such as brochures and maps.
Material that is white, gray and black and have no color or hue. Organic matter that is not solubilized after 1 hour of refluxing in an acid detergent of cetyltrimethylammonium bromide in 1N (Normal) sulfuric acid. ADF includes cellulose and lignin. lig nin. A type of paper, which does not contain any acidic substance that may affect acid sensitive material. Acid free paper is anti rust and is used for metal wrapping. The treatment of cellulosic, starch, or hemicellulosic materials using acid solutions (usually mineral acids) to break down the polysaccharides to simple sugars.. The transfer of acid from an acidic material to a less acidic or neutral-pH material. Occurs when neutral materials are exposed to atmospheric pollutants or when two paper materials come in contact. Acid can also migrate from adhesives, boards, endpapers, protective tissues, paper covers, acidic art supplies, and memorabilia. Page 2 of 88
Acid Proof Paper Acid Sizing Activated Carbon Activated Sludge Active Alkali (AA) Additives
Adsorbable Organic Halogen (AOX) Aerated Lagoon
Against the Grain Agglomeration Aging
Agitator
Air Brush Coater
A paper that is not affected by acid physically or chemically. This paper is used with substance containing acid. Internal sizing carried out in acidic pH range (0-7). Rosin and alum sizing is acid sizing. A highly absorbent powdered or granular carbon used for purification by adsorption. The biomass produced by rapid oxygenation of effluent. Caustic (NaOH) and Sodium sulfide (Na 2S) expressed as Na 2O in alkaline pulping liquor. Clay, fillers, dyes, sizing and other chemicals added to pulp to give the paper greater smoothness, color, fibered appearance or other desirable attributes. A measure of the amount of chlorine that is chemically bound to the soluble organic matter in the effluent. A biological wastewater treatment method in which air (oxygen) fed into an aeration basin reduces the effluent load.
Cutting, folding or feeding paper at right angles to the grain or machine direction of the paper. A cluster of particles or fibers. Irreversible alteration, generally deterioration, of the properties of paper in course of time. Aging also causes reduction in brightness and yellowing effect. Equipment used to keep content of a tank or chest in motion and well mixed.
A coater, which uses the pressurized air to atomize the coating mixture and spray it on the paper. Page 3 of 88
Air Dry (AD)
Air Drying Air Filter Paper Air Knife Coater
Air Laying or Air Laid Process Air Laid Nonwoven Air Laid Web Air Laid Pulp
Air Mail Paper Air Permeability
Air Pollution Albumin Paper Algae Alkali Lignin Alkali Resistance
Alkaline Extraction
Alkaline Papermaking
Alkaline Pulping
Alkenyl Succinic Anhydride (ASA)
Refers to the weight of dry pulp/paper in equilibrium with the atmosphere. Though the amount of moisture in dry pulp/paper will depend on the atmospheric condition of humidity and temperature but as a convention 10% moisture is assumed in air dry pulp/paper. Using hot air to dry pulp or paper sheets. A type of paper used for filtration of air to remove suspended particles. (car air filter, vacuum bag etc.) A device that applies an excess coating to the paper and then removes the surplus by impinging a flat jet of air upon the fluid coating, leaving a smooth, metered film on the paper. A nonwoven web forming process that disperses fibers into a fast moving air stream and condenses them onto a moving screen by means of pressure or vacuum. An air laid web that has been bonded by one or more techniques to provide fabric integrity. A web of fiber produced by the air ai r laid process. An air laid nonwoven that is produced with fluff, wood pulp. The web can be bonded with resin and/or thermal plastic resins dispersed within the pulp. It is lightweight, high opacity, good quality writing/printing type paper used for letters, flyers and other printed matter to be transported by airlines. Commonly referred to as "porosity." The ease with which pressurized air can flow through a paper's thickness. Typically measure by the Gurley or the Sheffield porosity tests, which measure the volumetric flow of air through the paper thickness. The contamination of air around the plant due to the emission of gases, vapors and particulate material in the atmosphere. A coated paper used in photography; the coating is made of albumen (egg whites) and ammonium chloride. Micro organic plant life that forms in i n paper mill water supplies. suppli es. Lignin obtained by acidification of an alkaline extract of wood. Freedom of paper from a tendency to become stained or discolored or to undergo a color change when brought in contact with alkaline products such as soap and adhesives. Alkaline extraction, i.e. E stage, is used in lignin removal before or between bleaching stages; the stage is often enhanced with an oxidizing agent, oxygen (Eo stage), hydrogen peroxide (Ep stage) or both (Eop stage). Paper manufactured under alkaline conditions, using additives, basic fillers like calcium carbonate and neutral size. The anti -aging properties in alkaline paper make it a logical choice for documents where permanence is essential. Pulping by alkaline solutions of sodium hydroxide, with or without sodium sulfide. Without sodium sulfide it is called soda process and with sodium sulfide it is known as Kraft or sulfate process. ASA is a sizing agent designed to increase resistance to water penetration in the case of paper formed under neutral or alkaline conditions. ASA is especially used in cases where full cure is desired before the size press and where it is important to maintain a high frictional coefficient in the paper product. ASA can improve paper machine runnability and preserve paper's dimensional stability by limiting penetration of size-press solution into the sheet. Page 4 of 88
Alpha Cellulose Alpha Pulp
Alternative Fibers Alum
Aluminium Foil Lamination
Annual Vegetable Fiber or Agricultural Residue Fiber Anaerobic Reactor System Anthra Quinone (AQ) Anti-foam or Defoamer Anti-Oxidant Board
Antiquarian Anti Rust Paper Antique Finish Applicator Apparent Density Apparent Viscosity Approach Flow System
The portion of the pulp or other cellulosic material that will not dissolve in 17.5% NaOH (Sodium Hydroxide) solution at 20oC. A specially processed, high alpha cellulose content, chemical pulp. It is also called dissolving pulp.
Common name for non-wood or tree free fibers. The paper maker alum is hydrated Aluminum Sulfate {Al 2(SO4)3}. It is used to adjust the pH of the mill water or as a sizing chemical in combination with rosin size. The combination of thin Aluminium foil with a paper backing used as a positive moisture barrier. Normal combination is kraft backing with Aluminium foil laminated to the kraft by means of asphalt, adhesive, or polyethylene. The Aluminum foil can also be coated with polyethylene. A source of fiber for pulp and papermaking, including, for example, wheat or rice straw or other fibrous by-products of agriculture. An effluent treatment system that uses microbes in the absence of oxygen to break down effluent constituents into methane, carbon dioxide and hydrogen sulfide. A quinoid compound added to white liquor (alkaline cooking liquor) to improve pulp yield and to increase the rate of delignification. Chemical additives used at wet end to reduce or eliminate tendencies of the machine white water to foam. Boxboard chemically treated to increase the shelf life of foods containing fats and oils by retarding rancidity of such products when packaged in cartons made of it. The treatment does not change the appearance of the board and is non-toxic and odorless. The largest available handmade paper (53 x 31 inches or 134.6x78.7 cm). Paper containing added substances which give it the property of protecting the surfaces of ferrous metals against rusting. A term describing the surface, usually on book and cover papers, that have a natural rough finish. Means of applying the aqueous coating, sizing or coloring to the paper web. Weight (mass) per unit volume of a sheet of paper obtained by dividing the basis weight by the Caliper (thickness). A characteristic of multi-component liquids that have a variable ratio of shear stress over shear rate (variable vi scosity depending on conditions). The stock flow system from fan pump to headbox slice. The term approach flow system refers specifically to the fan pump loop where in the pulp mixture is measured, diluted, mixed with necessary additives, and finally screened and cleaned before being discharged on to paper machine wire. Page 5 of 88
Aqueous Coating
Archival Paper Art Paper
Artificial Parchment
Ash Content
Aseptic Packaging
Asphalt Laminated Paper Automatic Packaging System
Azure
Back Liner Backbone Backing Roll Backing up
A water-based coating applied after printing, either while the paper is still on press ("in line"), or after it's off press. An aqueous coating usually gives a gloss, dull, or matte finish and helps prevent the underlying ink from rubbing off. Unlike a UV coating or a varnish, an aqueous coating will accept ink-jet printing, making it a natural choice for jobs that require printing addresses for mass mailings. A paper that is made to last for long time and used for long lasting records. High quality and rather heavy two-side coated printing paper with smooth surface. The reproduction of fine screen single- and multicolor pictures ("art on paper") requires a paper that has an even, well closed surface and a uniform ink absorption. Wood free paper that is produced by fine and extended grinding of certain chemical pulps and/or the admixture of special additives. As a result of the "smeary" grinding, the fiber structure closes homogeneously. It is used e.g. for wrapping meat and sausages or as corrugating medium for biscuit packaging The residue left after complete combustion of paper at high temperature. It is generally expressed as percent of original test sample and represents filler content in the paper. Extends the shelf life of non-refrigerated beverages and foods. Laminates and extruded coatings applied by the customer ensure an appropriate liquid barrier. Aseptic grade board is clay-coated on one side and is suitable for gravure, offset, and flexographic printing. Two sheets of natural kraft paper laminated in a single ply by means of asphalt. This is used as a moisture barrier; also to resist action of weak acids and alkalis. Term applicable to any one of several available systems for open mouth and valve bag packaging where bags are automatically applied to filler spout, filled, weighed, closed (if open mouth), palletized, and shrink wrapped.
The light blue color used in the nomenclature of "laid" and "wove" papers.
The back side layer in a multi-ply paperboard. Normally back liner is made out of inferior grade pulp compared to top liner. The back of a bound book; also called the spine. Rubber covered roll against which the metering device such as rod or blade can press. Printing the reverse or back side of a sheet that has already been printed on one side.
Page 6 of 88
Back Water
[see White Water]
Baffle Bag House
A device which obstructs the flow of fluid, whether to aid mixing or restrict the flow rate. An air pollution control device that captures particulate in filter bags.
Bag Paper Bagasse
Any paper made to be used in the manufacturing of bags. Sugarcane residue left after extracting the juice.
Baggy Roll
Mill roll defect usually associated with a variation in caliper and/or basis weight across the width. Rolls are normally checked for baggy areas by striking with a baton and listening for variations in audible pitch. A large rectangular shaped compressed package of waste paper, rag, pulp etc. Bale dimensions and weight varies widely depending on the baling material and handling capabilities.
Bale
Baling
Compressing and wrapping a material with wire, twine, string to form a unit which is more readily handled, stored and transported. Page 7 of 88
Bamboo
A plant of grass family grown in Asian countries and used for papermaking fibers.
Banknote or Currency Paper
Used for printing currency. De-facto highest grade of paper. Very high folding endurance, permanency, tensile strength, suitable for 4-colour printing, with watermark and other falsification safeguards such as embedded metal strip. Often contains cotton fibers. The outer protective layer of a tree outside the cambium comprising the inner bark and the outer bark. The inner bark is a layer of living bark that separates the outer bark from the cambium and in a living tree is generally soft and moist. The outer bark is a layer of dead bark that forms the exterior surface of the tree stem. The outer bark is frequently dry and corky An equipment used to remove bark from wood.
Bark
Barker or Debarker
Barking or debarking Barograph Paper
Base Paper or Base Stock
Removing bark from wood. Red thin paper coated on one side with a white wax, so that the needle of the barograph make a red line on a white ground, sold in rolls and coils and to suit the type of barograph. Refers to paper that will be subsequently be treated, coated or laminated in other ways. Page 8 of 88
Basic Dye
Basis Weight
Bast Fibers
Bastard Size Batch Cooking Batt Beater
Dye that have a positive charge due to amine groups and have a strong affinity for the surfaces of high-yield fibers. Basic dyes are economical, have high color strength but very poor lightfastness. In English system of units, basis weight is the weight in pounds of a ream (500 sheets) of paper cut to a basic size. (Basic size differs from category to category of the paper. Basic size for Bond and Ledger is 20"x26", book, offset and text paper have basic size of 25"x38"). In metric system of units, basis weight is the weight in grams of a single sheet of area one square meter. Basis weight is also called as substance and grammage in metric system of units. Fibers derived from the bark of some annual plants such as flax, gampi, hemp, jute, kozo and mitsumata etc. Main characteristic of these fiber is long length.
The non-standard sheet size of a given grade. A chemical A collection of fibers assembled into a sheet suitable for needle punching. The term is synonymous with web. An equipment used for beating, refining and mixing pulps.
Page 9 of 88
Beater Dye Beater Loading Beating or Refining
Belt Washer Bending Resistance/Flexural Stiffness Bible Paper Binder Binder (Coating) Biocide Biodegradable Biochemical Oxygen Demand (BOD)
Biological Waste Water Treatment Biomass
Biomass Boiler or Hogged Fuel Boiler
Bio-sludge Bitokoshi
Black Liquor Blackening
Blank or Black Box
Blade Coater
Dye added to the beater to color the pulp. Addition of a filler to the pulp in the beater. The mechanical treatment of the fibers in water to increase surface area, flexibility and promote bonding when dried. One of the unintended effect of beating is fiber length reduction. Washer, which uses rotating wire for dewatering and washing of pulp. Corrugated board's ability to resist bending, along with its edge crush resistance, relates to the top-to-bottom compression strength and general performance of corrugated containers. Thin white opaque heavily loaded, used for printing bibles. Not suitable for pen and ink, because of its absorbency. Chemicals which facilitate fiber bonding. A natural or synthetic compound used to adhere coating to the paper surface. A biological control chemical such as fungicide or a bactericide used in papermaking. Capable of destruction by biological action. When effluent containing biodegradable organic matter is released into a receiving water, the biodegradation of the organic matter consumes dissolved oxygen from the water. The BOD of an effluent is an estimate of the amount of oxygen that will be consumed in 5 days following its release into a receiving water; assuming a temperature of 20°C. A method of cleaning up waste water using living micro-organisms such as bacteria Any plant-derived organic matter. Biomass available for energy on a sustainable basis includes herbaceous and woody energy crops, agricultural food and feed crops, agricultural crop wastes and residues, wood wastes and residues, aquatic plants, and other waste materials including some municipal wastes. Biomass is a very heterogeneous and chemically complex renewable resource.. Biomass boilers burn bark, saw mill dust, primary clarifier sediment and other solid waste, and other wood-related scrap not usable in product production. Also called "hogged fuel" boilers, biomass boilers make steam and heat for mill use. Sludge formed (in the aeration basin) during biological waste water treatment or other biological treatment process. Bitoko/Bitokoshi is a grade of printing and writing paper unique to Japan. It is a very lightly coated paper, occupying a niche market between LWC and coated woodfree papers. The furnish includes both chemical and mechanical pulp in variable proportions, thus the Japan Paper Association (JPA) recognises both woodfree bitokoshi and mechanical bitokoshi depending on the proportion of mechanical pulp in the furnish. The liquor that exits the digester with the cooked chips at the end of the Kraft cook is called "black" liquor. Defect associated with calendered paper occurring as unintended local areas of apparently darker or grayer color due, for example, to the paper being too damp when passed through the calender. A flat sheet of corrugated or solid fiberboard that has been cut, slotted and scored so that, when folded along the score lines and joined, it will take the form of a box. A device that first applies a surplus coating to paper and then remove extra Page 10 of 88
color after evenly leveling by means of a flexible steel blade.
Bleach Plant Bleaching Bleaching Sequences Bleed
Bleed (corrugation) Bleed Fastness Bleed Through Blending or Mixing Blind Drilled Roll
Section of a pulp mill where pulp is bleached A chemical process used to whiten and purify the pulp. Bleaching also adds to the sheet's strength and durability. Series of subsequent bleaching stages, typically described by abbreviation such as CEHH (Chlorination, Extraction Hypochlorite, Hypochlorite . The feathered edge of inks caused by absorption into un-sized paper.
The penetration of laminating agents, such as asphalt, through the kraft plies making up the combination. The ability of a dye to remain attached to fibers in paper even when exposed to fluids or to sweaty hands. When printing on one side of a sheet of paper shows through to the other side. Blending of different pulps in a chest to achieve quality of the final product. A matrix of small holes drilled into the soft press roll which aid the water removal capability of that roll.
Page 11 of 88
Blind Embossing Blister Blister Pack
Blister Resistance Blotting Paper Blow Blow Heat Recovery System Blow Tank Blue Angel
Board
Boil Out
Bond Paper
Bonding Strength
A printing technique in which a bas-relief design is pushed forward without foil or ink. Defect on a paper surface often shaped like a human blister. It is due to delamination of a limited portion of paper without breaking either surface. This term describes a packaging system that is a combination of board and plastics. The board, usually made from lower grades of waste paper, can be lined in whole or in part on one or both sides, to carry a printed message or advertising. The product is sealed to the board by a transparent plastic film. This system is often used for small products with difficult shapes and sizes.
Resistance of paper to developing blister during printing and print drying. An un-sized paper used generally to absorb excess ink from freshly written manuscripts, letters and signatures. It is the discharging of the pressure and contents of the digester in to blow tank.
The system used to recover heat from the flash steam generated while digester is blown in to blow tank. The tank in which cooked chips and spent liquor is blown from digester at the end of the cooking cycle. It is label defined by the German Federal Environmental Agency. The Blue Angel label is awarded to papers which do little damage to the environment. The paper is controlled in detail: its composition, its production process and its conversion. Only papers made from 100 % post consumer waste paper are certified.. Thick and stiff paper, often consisting of several plies, widely used for packaging or box making purposes. Its grammage normally is higher than 2 150 g/m or thickness is more than 9 point ( thousandth of an inch). The occasional cleaning of a paper machine system, during a shut-down, by filling the system with a hot solution the usually contains detergent and either NaOH, an acid, or an enzyme. The name "bond" was originally given to a paper, which was used for printing bonds and stock certificates. It is now used in referring to paper used for letterheads and many printing purposes. Important characteristics are finish, strength, freedom from fuzz, and rigidity. The internal strength of a paper; the ability of the fibers within a paper to hold to one another. Bonding strength measures the ability of the paper to hold together on the printing press or other converting processing machines. Good bonding strength prevents fibers from coming loose ("picking"). Bonding strength of fiber is improved by beating/refining and/or adding bonding agent. Page 12 of 88
Bone Dry Book Paper Bow Roll
Box Boxboard Breaking Length
Breaks
Breast Roll
Brightness
Bristol Board Brittleness
Moisture free or zero moisture. A general term used to define a class or group of papers having in common A paperboard used in the manufacture of light non -corrugated container. Bow Rolls are also known as Banana Rolls, Spreader Rolls, Curve rubber expander. Bow rolls are useful for removing of wrinkles, slack edges, spreading and slit separation. Most of the Expander Rolls are driven by web tension itself without any extra drive. Bowed Rolls are key component to making wrinkle free paper as well as keeping clothing in top working condition on some Paper Machines.
A rigid container having closed faces and completely enclosing its contents. A class of board frequently lined on one or both sides, with good folding properties and used for making box and car tons. The length beyond which a strip of paper of uniform width would break under its own weight if suspended from one end. Usually expressed in meters. Rupture of paper on the paper machine during paper making. It the paper on couch roll, it is termed couch break. If the paper breaks in paper section, it is termed as press break. If the paper breaks in dryer section, it is dryer breaks and so on. A medium size metal or plastic/fiberglass/granite covered roll located at the headbox side of the paper machine to support the wire.
The reflectance or brilliance of the paper when measured under a specially calibrated blue light. Not necessarily related to color or whiteness. Brightness is expressed in %. CIE Brightness: An internationally-recognised standard of paper brightness developed in Europe by the Centre Internationale d'Eclairage (CIE). A fine quality cardboard made by pasting several sheets together, the middle sheets usually of inferior grade. Property of paper causing it to break while bending. Page 13 of 88
Brocade
A heavily embossed paper.
Broke
Paper that is unusable because of damage or non-conformity to the specifications. It is put back in to the pulping system. A pit below the machine in to which broke is disposed from the machine floor. A broke pulper is used to break down the broke into a stock that can be pumped and treated. This term can cover a wide range of machines and is often used to refer to both stand alone broke pulpers and under the machine (or UTM) pulpers which receive paper directly from the machine including any trim. A stand alone broke pulper is used to process finished reels that have been rejected or for broke that for any reason has been baled or collected away from the UTM pulpers.
Broke Pit Broke Pulper
Brown Pulp
Brown Stock Brush Coating
Buffering
Bulk Burnout Burnt Paper
A mechanical pulp made from wood, which is steamed before grinding. The color-bearing, non-cellulosic components of the wood remain with the pulp. The pulp is generally used for wrapping and bag paper. The unbleached chemical pulp. A Coating method in which the freshly applied coating color is regulated and smoothed by means of brushes, some stationary and some oscillating, before drying. The neutralizing of acids in paper by adding an alkaline substance (usually calcium carbonate or magnesium carbonate) into the paper pulp. The buffer acts as a protection from the acid in the paper or from pollution in the environment. Reverse of density, expressed as cubic centimeter per gram. The loss of color during drying. Paper, which has been discolored and is bri ttle, but otherwise intact.
Page 14 of 88
Burst
Burst Factor
Burst Index
Burst Ratio
Bursting Strength
C1S C2S Calcium Carbonate
Calender
Calender Blackening
An irregular separation or rupture through the paper or package. Air Shear burst : Burst caused by air trapped in the winding roll producing rupture of the web along the machine direction. Caliper shear burst . Cross Machine tension burst that generally occurs between an area or relatively high and low caliper extending for some distance in the machine direction; due to non uniform nip velocities between hard and soft sections of the roll. Core burst: Inter-layer slippage just above the core, often over the key way, which terminates an Air Shear Burst. Core bursts are most often seen on core-supported unwinds and winders. The ratio of the bursting strength (expressed in g/cm2 ) and the substance of paper/paperboard (expressed in g/m2) determined by standard methods of test. The ratio of the bursting strength (expressed in kilo Pascal ) and the substance of paper/paperboard (expressed in g/m2) determined by standard methods of test. 2 The ratio of the bursting strength (expressed in lb/inch ) and the substance of paper/paperboard (expressed in lb/ream) determined by standard methods of test. The resistance of paper to rapture as measured by the hydrostatic pressure required to burst it when a uniformly distributed and increasing pressure is applied to one of its side. Coated on one side of the paper. Coated on both sides of the paper. CaCO3, a naturally occurring substance found in a variety of sources, including chalk, limestone, marble, oyster shells, and scale from boiled hard water. Used as a filler in the alkaline paper manufacturing process, calcium carbonate improves several important paper characteristics, like smoothness, brightness, opacity, and affinity for ink; it also reduces paper acidity. It is a key ingredient in today's paper coatings. A stack of highly polished metal cylinders at the end of a paper machines that smoothes and shines the paper surface as sheets pass through.
Coverage of calendered paper web with glazed translucent spots due to excessive calender roll heat, calender pressure, poor and/or excessive and uneven moisture. Page 15 of 88
Calender Cut Calender Spots
Weak lines or fractures in paper that break easily under tension, caused by wrinkles going through the calender stack of the paper machine. Paper defect usually indicated as a transparent spot in the sheet; caused by foreign material adhering to a calender roll and being impressed into the sheet with each revolution.
Calendering
Passing paper web through a stack of calender rolls. The main object of calendering is to impart the desired finish to paper. Machine Calendering: Paper passes through one or more nips formed by a set of iron rolls. Super-Calendering: Paper passes through one or more nips formed by steel roll and a fiber roll made of compressed fibrous material. Gloss Calendering: Paper passes through one or more nips formed by soft roll (e.g. rubber covered) and highly smooth mirror like finish steel roll at high temperature. Matt Calendering: Any calendering technique used to produce a smooth surface without a considerable increase in gloss. Friction Calendering: The calendering is achieved by speed differential between rolls. The paper passes through one nip (2 steel rolls) or 2 nips (2 steel rolls separated by a fiber roll) in which rolls are driven independently and speed variation may be from 10 to 30%. Brush Calendering: The paper is pressed against a cylindrical brush by a backing roll or by web tension. The circumferential speed of the brush is several times higher than the web speed.
Caliper
The thickness of paper usually expressed in thousandths of an inch in English system of units and in millimetres in Metric system of units. Larger diameter in the centre of a papermaking rolls (press & calender etc), compared to the ends, to compensates the deflection of roll due to its own weight.
Camber
Canadian Standard Freeness (CSF) Capacity Utilization Rate
It is a measure of pulp freeness. The unit of measurement is ml CSF. The production rate a plant or machine is operating with respect to design capacity. Also in some cases it indicates the efficiency (%) at which a plant or machine is operating. Page 16 of 88
Carbohydrate
Carbon Dioxide Equivalency/CO2e
Carbon Footprint
Carbon Paper
Carbon Offset
Carbonless Paper Cardboard Carton Cartridge paper
Casein Cast Coater
Causticizing
Cellulose
Organic compounds made up of carbon, hydrogen, and oxygen and having approximately the formula (CH2O) n; includes cellulosics, starches, and sugars. Effective greenhouse gas emissions expressed as equivalent tonnes of carbon dioxide. Some greenhouse gases have a stronger warming effect than others; the CO2e measure provides an appropriate comparison of the warming effects of every greenhouse gas. The total set of Green House Gases (GHS) emissions caused directly and indirectly by an individual, organization, event or product by UK Carbon Trust. A low basis weight paper (8 to 15 g/m2) with very low air permeability, free of pin holes and with a waxy coating, that is used to produce carbon copies on typewriters or other office equipment. An emissions reduction credit relating to another organization’s project
that results in less greenhouse gases in the atmosphere than would otherwise occur. A paper that uses a chemical reaction between two different contacting coatings to transfer image when pressure is applied. A thin, stiff paperboard made of pressed paper pulp or sheets of paper pasted together. Used for playing cards, greeting cards, etc. A folding box made from boxboard, used for consumer quantities of product. A carton is not recognized as a shipping container Tough, slightly rough surfaced paper used for a variety of purposes such as envelopes; the name comes from the original use for the paper which formed the tube section of a shotgun shell. Protein derived from skim milk and used in the sizing of paper and as an adhesive in the manufacture of coated papers. A device that applies a wet coating color to a paper web before it contacts a heated drum having a highly polished surface, which cast the coating in to an image of the smooth, mirror-like drum surface. It is the process in which Green Liquor is converted in to White Liquor. Technically speaking it is the process of converting sodium carbonate in to sodium hydroxide.
It is a high molecular weight, stereoregular, and linear polymer of repeating beta-D-glucopyranose units. Simply speaking it is the chief structural element and major constituents of the cell wall of trees and plants.
Page 17 of 88
Cellulose Fiber
Chain of Custody
Chalking Check or Cheque Paper Chelating Agent
Chelation
Chemical Ghosting
Chemical Oxygen Demand (COD)
Chemical Pulp Chemical Recovery Chemo-ThermoMechanical Pulp (CTMP) Chest
China Clay
An elongated, tapering, thick walled cellular unit, which is the main structural component of woody plants. Fibers in the plants are cemented together by lignin. In British English Fiber is spelled as Fibre. Thermal conductivity of cellilose fiber varies from 0.034 to 0.05W/m K, making it a good insulator. The process of tracking materials used within a manufacturing facility so that the source of raw materials used to make specific end products can be identified. Commonly applied in the context of use of certified fibre supplies. Improper drying of ink. Ink vehicle has been absorbed too rapidly into the paper leaving a dry, weak pigment layer which dusts easily. A strong, durable paper made for the printing of bank checks or cheques. An organic compound that forms more than one coordinate bond with metals in solution; organic compound participating in chelation; e.g. EDTA and DTPA. A chemical complexing (forming or joining together) of metallic cations (such as iron) with certain organic compounds, such as EDTA (ethylene diamine tetracetic acid); a reaction between a metallic ion and an organic compound that removes the metallic ion from solution. A light duplication of a printed image on the other side of the same sheet, created by chemical reaction by the ink during the drying stages; also referred to as "gas ghosting.". The amount of oxygen consumed in complete chemical oxidation of matter present in waste water; indicates the content of slowly degradable organic matter present. COD is easier to measure compared to BOD (Biological Oxygen Demand). Pulp obtained from the chemical cooking or digestion of wood or other plant material. It is the process in which cooking chemicals are recovered. Mechanical pulp produced by treating wood chips with chemicals (usually sodium sulfite) and steam before mechanical defibration. Vessel equipped with an agitating device for storing, collecting, mixing, blending and/or chemical treatment of pulp suspension. Chest can be horizontal and or vertical. Tower are special type of chest generally used in bleached plant to provide retention time and to provide down/upward flow out of pulp. Natural mineral, consisting essentially of hydrated silicate of alumina, used as a filler or as a component in a coating color.
Page 18 of 88
Chip
Wood chips produced by a chipper; used to produce pulp, fiberboard and particle board, and also as fuel.
Chipboard
A paperboard, thicker than cardboard, used for backing sheets on padded writing paper, partitions within boxes, shoeboxes, etc. The machine that converts wood logs in to chips.
Chipper
Chlorine Number
Chromo
Cigarette Paper
Clarifier
A test method to determine the bleach requirement of a pulp. It indicates the number of grams of chlorine consumed by 100 g of pulp under specified conditions. A term used to describe both papers and boards used for subsequent brush coating. The various qualities are determined both by the actual grade of base material used and the quality of the coating, which may be gummed. Coating may be applied to one or both sides, depending on end use. This light weight, unsized paper (grammage 18 to 24g/m2), converted to improve glowing. It normally has approx. 30% calcium carbonate as filler to control the burning rate and match it with tobacco burning rate. Very long fiber such as jute, cotton etc is used to achieve high strength and porosity. Basin where sludge is removed from treated effluent by settling.
Page 19 of 88
Clay
A natural substance used as both a filler and coating ingredient to improve a paper's smoothness, brightness, opacity and/ or affinity for ink.
Clay Coated Boxboard
A grade of paperboard that has been clay coated on one or both sides to obtain whiteness and smoothness. It is characterized by brightness, resistance to fading, and excellence of printing surface. Colored coatings may also be used and the body stock for coating may be any variety of paperboard. A conical or partly cylindrical device with no moving parts, designed to remove grit from thin-stock furnish by the centrifugal action of rotating liquid.
Cleaners
Closed Loop Recycling Closed System Clot Clump Coarse Paper (also Industrial Paper) Coat Weight
When a used product is recycled in to a similar product; a recycling system in which a particular mass of material is remanufactured into same product. Papermaking system wherein white water is mainly re-circulated and not discharged as effluent. Thick element composed of several entangled fibers. Its presence is harmful to the production process and needs to be eliminated. A knot of fibers resulting from improper separation of the fibers. Various grades of papers used for industrial application (abrasive, filter etc.) rather than cultural purposes (writing, printing etc.) The amount of coating applied to base paper, expressed as pounds of airdried coating on the surface of a 25X38 in ream or grams per meter square. Page 20 of 88
Coated Paper
Coated White Top Liner Coating Coating Color Coating Color Kitchen Cobb Test
Cockle Finish Cockling Cogeneration Coir Cold Blow
Color-fast papers Colored Kraft Colored Pigments
Combined Deinking Compression Strength (CD or MD)
Term that applies to paper which has a special coating applied to its surface. Material such as clay, casein, bentonite, talc, applied by means of roller or brush applicators; or plastics applied by means of roll or extrusion coaters. White liner that is coated to produce superior printability. Process by which paper or board is coated with an agent to improve its brightness and/or printing properties. Mixture used to coat paper and board: contains pigment, binder, special additives and water. Section of Coating Plant where coating colour is prepared and mixed Measures paper's water absorption rate and is expressed as the amount of water pick-up per unit surface area of paper by Tappi method T441. The test duration must be specified to properly know the absorption rate. United Nations (UN) and Code of Federal Regulations require the 30-minute pick-up must be 155 grams per square meter or less for containerboard used in hazardous material transport. Produced by air drying paper with controlled tension. This uneven surface is available in bond papers. When the surface of the paper has wave like appearance. It is the process to generate electricity from high pressure steam and using low and/or medium pressure steam in the mill process. Fiber derived from the outer husks of the coconut. Pressure ejection of cooked pulp from batch or continuous digesters after the pulp has been cooled to below 100oC. The cooling step reduces damage to the fibers. Colored papers that will not run when wet or fade under bright light. Natural or bleached kraft paper to which a dye or pigment has been added. These are water insoluble colored materials. They belongs in the category of fillers and loading material but are colored and used in small quantity. Pigments has no affinity to fiber and must be used in conjunction with alum or a cationic retention aid in order to retain them. Deinking process combining flotation and washing. Can be referred to as ring crush or "STFI (stiffy)". The amount of force needed to crush paper resting on its edge. Compression testers hold and support the paper specimen so as to emulate its position and orientation in the walls of a corrugated container. Due to the corrugated board making process, paper must support compressive loads orthogonal to their grain (a CD orientation). The test is unidirectional so the paper orientation during testing must be known.
Page 21 of 88
Coniferous Trees
Cone bearing and evergreen trees. Also known as soft wood trees. e.g. pine, spruce etc.
Consistency Consistency Regulator
The percentage of bone dry solids by weight in pulp or stock. A device or instrument used to regulate the consistency of the pulp on-line. Regulator works only in reducing the consistency i.e. add water, but can't remove water or thicken. Sheathing paper, roofing, floor covering, automotive, sound proofing, industrial, pipe covering, refrigerator, and similar felts. The paperboard components (linerboard, corrugating material and chipboard) used to manufacture corrugated and solid fiberboard. The raw materials used to make containerboard may be virgin cellulose fiber, recycled fiber or a combination of both. Production of pulp in continuous digester as compared to a batch digester.
Construction Paper Containerboard
Continuous Pulping
Contraries Contrast
Converting
Unsuitable material found in wastepaper which must be removed from the pulp before making it into paper, e.g. paperclips, string, plastics. The degree of difference between light and dark areas in an image. Extreme lights and darks give an image high contrast. An image with a narrow tonal range has lower contrast. The operation of treating, modifying, or otherwise manipulating the finished paper and paperboard so that it can be made into end-user products. Page 22 of 88
Cooking Cooking Liquor Cooling Cylinders or Cooling Drums Copier Paper or Laser Paper Copper Number Cord
Reacting fibrous raw material with chemical under pressure and temperature to soften and or remove lignin to separate fibers. Liquor made up of selected chemicals and used for cooking pulp. e.g. cooking liquor in kraft pulping mainly consist of NaOH and Na2S. Water cooled cylindrical metal vessel over which dry paper web after dryers is passed to cool the paper before calendering.. Lightweight grades of good quality and dimensionally stable papers used for copying correspondence and documents. It is the measure of degree of fiber degradation. It is weight of copper in grams reduced to cuprous state by 100 grams of pulp. Pulpwood volume measurement indicating a pile measuring 4 ft x 4 ft x 8 ft, equaling 128 ft³ (3.62 in³). A long cord measure 4ft x 5ft x 8ft equaling 160 ft3.
Core
Fibrous tube used to wound paper for shipment.
Core Plug
Metal, wood, particleboard, or other material plugs which are driven into the ends of the paper core of finished roll to prevent crushing of the core. An electrostatic treatment that reduces the surface tension of a substrate (e.g., a polycoated substrate) to ensure adhesion of ink and glue. The Corona treatment involves high voltage, high frequency electricity discharged from an electrode when it pours through the polycoated board increases the surface energy of the board to better receive inks or glue. Usually a nine-point board after if has passed through a corrugating machine. When this corrugated board is pasted to another flat sheet of board, it becomes single-faced corrugated board; if pasted on both sides, it becomes double-faced corrugated board or corrugated (shipping) containerboard. Containers made with corrugating medium and linerboard.
Corona Treatment
Corrugated Board
Corrugated Container
Page 23 of 88
Corrugated Medium or Media
Corrugator
Cotton Fiber
The wavy center of the wall of a corrugated container, which cushions the product from shock during shipment. Media can contain up to 100% postconsumer recycled fiber content without reducing its ability to protect the product. Machine that presses medium into flutes, applies glue to the medium and affixes sheets of linerboard to form corrugated board.
Cotton is a natural fiber and is one of the strongest and most durable fibers known to man. Papers manufactured of cotton fiber will last longer and hold up better under repeated handling and variant environmental conditions than paper made from wood pulp. Generally, given reasonable care, one can expect one year of usable life for every 1% of cotton contained in the sheet. Typically cotton fiber papers are made of either all cotton fiber (100% cotton) or a blend of cotton and wood pulp. Cotton "fibers" are made from unicellular hairs that grow out from the surface of the seed immediately after fertilization. The hairs are twisted into usable thread which is tough and strong. Cotton hairs (lint) of tetraploid (4n) species may be up to 50 mm long. In the cotton gin, fine brushes pull the lint off the seed by drawing it through holes too fine for the seeds to pass. Cotton thread is spun from countless billions of microscopic hairs covering the surface of cotton seeds, each hair up to 50 mm (2 inches) in length. The total length of hairs in a single cotton boll (one seed capsule) may exceed 300 miles. Imagine how many miles of cotton hairs are in a standard 500 pound bale. Cotton is the textile produced in the largest volume worldwide. (From http://waynesword.palomar.edu/traug99.htm )
Page 24 of 88
Cotton Linter Cotton Paper or Rag Paper Couch Pit or Hog Pit
The cotton fibers that adhere to the cottonseed used to produce pulp for cotton fiber papers. Paper made with a minimum of 25% cotton fiber. Cotton paper is also called rag paper. This is the pit below the couch roll. It collects water draining from this section, wet wire trim and any wet broke generated due to the paper break at the wire part. Couch pit has agitator (s).
Couch Roll
Couch roll serves the following functions 1) Main drive for the wire, 2) Transfer the wet sheet from wire part to press part and 3) Removes water (if suction type couch roll). Couch roll can be solid or suction type.
Cover Paper
Any wide variety of fairly heavy plain or embellished papers, which are converted into, covers for books, catalogs, brochures, pamphlets, etc. Good folding qualities, printability, and durability characterize it. 1. A defect in coated paper, caused by the separation of the coating layer on the formation of fissures in the surface of the coating due to printing or other converting process. 2. Crack at fold: Fissures in the crease when any paper is folded along a fold line. May be due to separation of coating or separation of fibers. More prevalent when the paper has been over-dried. In boards it may occur along score-folds even though the scoring has been done to minimize cracking at the fold. The term is also applied when coatings crack without fiber failure during a folding operation. 1. Deformation remaining from a fold over. 2. Cross direction wrinkles( Washboard): Fold over of a web in the cross machine direction, giving a crease running in the machine direction. 3. Blade crease: A crease essentially in the machine direction devoid of coating in the creased area. 4. Calender Crease: Usually a sharp crease caused by passage through the
Crack
Crease
Page 25 of 88
Creping
Crescent Former
Crinkles Cross-machine Direction Crystallization Cunit Curl
Customark
Cut Sheet
Calender of a crease or of a fold generated at the Calender; often cut through when it is preferable to call it a Calender out. 5. Smoothed crease: A flattened-out crease running mainly in the machine direction. Can occur at the wet press section, dryer (dryer wrinkles), size press, winder or sheeter. The operation of crinkling a sheet of paper to increase its stretch and softness.
Sheet forming section in a tissue machine, with the pulp suspension jet-out of the headbox flowing between a felt and a wire both moving at the same speed. A defect in linerboards caused by the separation of the liner ply and/or the formation of fissures (cracks) in the surface of the liner during creasing. A direction perpendicular to the direction of web travels through the paper machine. A condition of a dried ink film, which repels another ink printed on top of it. A term used in the measurement of pulpwood, i.e. 100 cubic feet of solid wood, bark excluded. One cunit corresponds to 2.83 c ubic meter of wood. Tendency of paper by itself to bend or partly wrap around the axis of one of its directions.
A customark is a watermark made with a rubber printing plate treated with a tranparentizing solution that leaves a mark in the paper. This process produces a wire appearance in which the mark is lighter than the surrounding paper. It can be produced in smaller quantities and at a lower price than a genuine watermark, which requires a dandy roll. Paper cut in sheets (letter, legal, A, B or any other standard size) to be used in printer, photocopier, fax machines etc. Page 26 of 88
Cutter Cutter Dust Cutting (Refining) Cylinder Mould or Cylinder Machine
Damp Streaks Dampening
Dandy Roll
Debossing
A machine in the Finishing House of a paper mill, used for converting paper from reel to specific sheet sizes. Small loose paper particles which chip out of the edges of a sheet of papers as it is cut by the chopping blade and/or disc knives on a sheet cutter. A refining or beating action that splits the fibers in to two or more pieces. It is a type of papermaking machine. Wire-covered cylinders are rotated through a vat of pulp, and paper is formed as the water drains from the cylinder. Cylinder machines are used primarily to manufacture paperboard. Multi-cylinder machines produce multi-layered paperboard (one layer for each cylinder).
Streaks caused by uneven pressing or drying during paper manufacturing. The process of keeping the non-image areas of lithographic plates to be ink repellent by applying aqueous Fountain solution to the plate from the Dampening system. A hollow wire covered roll that rides on the paper machine wire and compacts the newly formed wet web to improve the formation and if required to impart watermark or laid finish the paper.
Pressing letters or illustrations into a sheet of paper using a metal or plastic die to create a depressed (debossed) image.
Page 27 of 88
Deciduous Trees
Broad leafed or hardwood trees which lose their leaves in fall such as birch, maple etc.
Decker Deckle
A drum type filter used for pulp thickening. The width of the wet sheet as it comes off the wire of a paper machine. Also defied as the wood frame resting on or hinged to the edges of the mould that defines the edges of the sheet in handmade papermaking or strap or board on the wet end of a paper machine that determines the width of the paper web. The untrimmed, feathery edges of paper formed where the pulp flows against the deckle. A device that removes entrained and dissolved air from dilute stock furnish by applying vacuum as the stock is sprayed into an open chamber, usually at the outlet of cleaners. A device on a web press or sheeter used to remove paper curl. Separation of wood fibers by mechanical and/or che mical means. Deflaker mechanically treat the fiber flakes and bundles of fibers in the stock in order that they are broken down into individual fibers in a suspension if possible. This is done for a number of reasons and in a number of positions within the system. It can be installed to reduce remaining flakes after a pulper, in the broke system to reduce flakes going back to the machine from the broke pulpers and can also be used in the final stages of a screening system in a recycled fiber line to treat the concentrated rejects and the flakes contained within it.
Deckle Edge Deculator
Decurler Defibration Deflaker
Degree of Polymerization (DP) Deinked Pulp (DIP) Deinking
As applied to cellulose, refers to the average number of glucose unit in each cellulose molecule of a pulp sample. Usually determined by the CED viscosity test. Paper pulp produced by deinking of recovered paper The process of removing inks, coatings, sizing, adhesives and/ or impurities from waste paper before recycling the fibers into a new sheet.
Page 28 of 88
Deinking Cell
A vessel or chest used to treat recycled paper with chemical to remove ink.
Delamination
The separation of the layers of a multiplex paper/paperboard/corrugated board.
Delignification
The removal of lignin, the material that binds wood fibers together, during the chemical pulping process. Material that has the ability to absorb enough moisture from the surrounding atmosphere to revert it to a liquid form. Examples of deliquescent include calcium chloride and ammonium nitrate. A sensitive photoelectric instrument that measures the density of photographic images or of colors. Used in quality control to accurately determine the consistency of color throughout the run. Reducing the resin (pitch) content of wood prior to cooking either by storage or using bleaching chemicals to reduce the resin content in pulp.
Deliquescent
Densitometer
Deresination
Page 29 of 88
Digester
The reaction vessel in which wood chips or other plant materials are cooked with chemical to separate fiber by dissolving lignin.
Digital Printing
1. Printing by imaging systems that are fed imaging information as digital data from pre-press systems. 2. Computer –to-plate Systems, which use printing plates, or other images carriers that do not require intermediate fil ms. 3. Computer-to-print (Plateless): Systems that produce reproductions directly on the substrate without the need for intermediate films or plates A. Electronic printers: Electrophotographic printers, for black or single color, used for short-run variable information and ondemand book publishing. B. Color copiers: Usually Electrophotographic printers, for spot or four color process printing, used for making one or several copies of spot or four color process subjects. C. Electronic printing systems: Electrophotographic, magnetographic, monographic, field effect, ink jet or thermal transfers printing. For One-colour, four color process or up to sixcolor printing. Used for some degree of variable information, ondemand. Examples of use are direct mail, temporary product labels for trade shows, billboard posters and the like. The ability of paper or paperboard to maintain size. It is the resistance of paper to dimensional change with change in moisture content or relative humidity. Dimensional stability is essential for keeping forms in registration during printing and keeping sheets from jamming or wrinkling on press or in laser printers. A group of 75 chlorinated compounds. Dioxins are formed in a complex process, where chlorine combines with other additives during bleach ing. Batch cooking in which digester contents are heated by blowing steam directly into the digester. Dye molecules that are sufficiently large and planar that they tend to remain on a fiber surface without need of a fixative. Direct dyes have moderate lightfastness but duller shades Dependency of a given paper property on the orientation of the fiber in paper e.g. CD or MD.
Dimensional Stability
Dioxin Direct Cooking Direct Dye
Directionality
Page 30 of 88
Dirt Dirt Count
Dispersion
Dispersants Displacement Washing Dissolving Pulp Doctor Blade
Document Paper
Double Coating Down Cycling
Drainage or Dewatering Draw Dregs Drum Reel
Dirt in paper consists of any imbedded foreign matter or specks, which contrast in color to the remainder of the sheet. The average amount of dirt specks in a specific size of paper area. Both virgin sheets and recycled sheets have "dirt," although recycled paper usually has a slightly higher dirt count than virgin paper. However, it rarely affects recycled paper's quality and use. A distribution of small particles in a medium. It also describes the uniform suspension of fibers in water for wet forming. Following the deinking process of waste papers, residual ink particles are dispersed into tiny bits that are usually invisible to the eye. Bleaching the fibers helps to remove the last of the inks and improve paper brightness. Substances such as phosphates or acrylates that cause finely divided particles to come apart and remain separate from each other in suspension. An event of pulp washing in which washing liquid displaces free liquor from a pulp bed in order to improve the washing; enables washing with reduced amount of water. A high purity special grade pulp made for processing in to cellulose derivatives including rayon and acetate. Thin metal plate or scraper in contact with a roll along its entire length to keep it clean. Blades are also used for creping.
Document paper is paper with a high ageing resistance. It is woodfree but may also contain rags or be fully made from rags and is used for documents that have to be preserved for a longer period. Coating of paper or paperboard twice on one or both sides. Every time cellulose fibers are recycled they deteriorate slightly and become contaminated, so the new product is of lower quality than the original product which went to form the waste; the progressive deterioration of fibers means that there is a limit to the number of times they can be recycled, thus the term down cycling is used as a more accurate description of recycling. Removal of water from wet web during formation of paper sheet. Difference in speed between two adjacent section of the paper machine. The solids which settle down in the clarifiers in the Causticizing process. The reel drum (also called a "pope reel") is motor driven under sufficient load to ensure adequate tension on the sheet coming from the calendars. The web wraps around the reel drum and feeds into the nip formed between the drum and the collecting reel.
Page 31 of 88
Drum Washer Dry Coating Dry End Dry Line
Dry Offset
Dryer Felt
One type of pulp washers; uses pressure gradient and filtration for dewatering and displacement. Coating method in which a binder is applied to the paper surface followed by dry coating pigment. That part of the paper machine where the paper is dried, surface sized, calendered and reeled. The dry line is the location on a Fourdrinier paper machine forming section where the appearance of the wet web of paper changes abruptly. Before the dry line the furnish has a glossy, wet appearance. After the dry line the wet web appears dull. The optical change is related to the effect of fibers poking through the air-water interface. On a well-adjusted paper machine the dry line ought to be straight. Increased refining and lower freeness of the pulp tend to move the dry line in the direction of the couch. Chemicals that promote drainage tend to move the dry line in the direction of the slice. Uses a rotary letterpress plate on an offset press. Because the image is relief, the method requires no dampening. Image is transferred to a rubber blanket, then to paper. A continuous cotton and or synthetic belt and used in the dryer section of a paper machine to press and maintain positive contact of the web against the surface of the dryer cylinder.
Page 32 of 88
Dryer Screen
Drying
Duplex Bag Duplex Board Duplex Paper Dust
Dye
Edge Crush Resistance
Edge Cutter
Effective Alkali Effluent Electrical Grade Paper
Electric Resistivity
Electronic Printing Electro photography
A type of dryer felt made of synthetic material, with very high open area to provide easy escape to vapors formed due to water evaporation. Dryer screens are used in the later part of dryer section where paper is >60% dry to avoid any screen impression. This is the final stage of water removal from wet web of the paper formed on wire. After pressing the moisture content of the web is apprx. 40-45%. The remaining water (up to 95% dryness) is removed by evaporation . This is done by moving the web around a series of steam heated iron drums in the dry end of the paper machine. Two-ply bags. Paperboard made with two plies or layers. Normally two layers are formed and joined together at wire part. Paper made with two plies or layers. Normally two layers are formed and joined together at wire part. Loose flecks of fiber, filler and/or coating on the paper that sometimes sticks to the printing blanket and prevents ink from reaching the paper surface. A chemical compound having the ability to absorb visible light over a certain range of wavelengths so that the diffusely reflected light appears colored. Dye can be basic, acidic or direct. The amount of force needed to crush on-edge of combined board is a primary factor in predicting the compression strength of the completed box. When using certain specifications in the carrier classifications, minimum edge crush values must be certified. Device comprising two jets of water which are adjustable across the wire and which divide the wet web on the wire lengthwise so that the edges may be removed, generally at the couch. In this way they control the width of the web going forward from the wire part and give it compara tively clean edges. Caustic (NaOH) and one half of Sodium sulfide (05*Na2S) expressed as Na 2O in alkaline pulping liquor. Waste backwater and rejects from which fiber is recovered prior to discharge from the mill. Strong, pin-hole free paper, sometimes impregnated with synthetic resins and made from unbleached Kraft pulp. Electrical insulating paper must neither contain fillers nor conductive contaminants (metals, coal, etc.) nor salts or acids. Lava stone bars are used on rotor and stator to avoid any metal contamination. Cable papers, that are wound around line wires in a spiral-like fashion, are electrical insulating papers with a particularly high strength in machine direction. Electrical grade papers include cable papers, electrolytic papers and capacitor paper. Resistivity characterizes how a sheet of paper accepts and holds a charge. Since the electrostatic processes uses an electrical charge to form the print image, the electrical properties of the sheet are important to the overall imaging process. Photocopiers, ink jet, laser printers and other similar printing methods that create images using electrostatic charges rather than a printing plate. A printing process that uses principles of electricity and electrically charged particles to create images - e.g., photocopiers and laser printers.
Page 33 of 88
Electrostatic Precipitator (ESP)
Used to clean up flue and process gases. Removes 99.5-99.8% of dust particles emitted from recovery boilers, lime kilns and bark-fired boilers.
Elemental Chlorine Free (ECF)
ECF papers are made exclusively with pulp that uses chlorine dioxide rather than elemental chlorine gas as a bleaching agent. This virtually eliminates the discharge of detectable dioxins in the effluent of pulp manufacturing facilities. A property of paper that allows it to stretch. Pressing a shape into a sheet of paper with a metal or plastic die, creating a raised (embossed) image. Coating of paper with an emulsion containing plastic or resin. A general term referring to coated paper that has a higher basis weight than coated publication (magazine) paper but a lower basis weight and caliper than coated cover paper. Old term used for beater sizing when sizing chemicals used to be added in Engine or Beater. A smooth-finished, machine made and calendered book paper. It is soft, dull and pliable. Normally used for letterpress printed magazines. A printing process using intaglio, or recessed, plates. Made from steel or copper, engraved plates cost more than plates used in most other printing processes, such as lithography. Ink sits in the recessed wells of the plate while the printing press exerts force on the paper, pushing it into the wells and onto the ink. The pressure creates raised letters and images on the front of the page and indentations on the back. The raised lettering effect of engraving can be simulated using a less costly process called thermography. Entrained air consists of bubbles that are small enough (say less than 1 mm) to move along with the fibers. The paper made specifically for die cutting and folding of envelopes on high-speed envelop machine. EPP should have at least two of the following three characteristics:
Elongation Embossing Emulsion Coating Enamel
Engine Sizing English Finish Engraving
Entrained Air Envelop Paper Environmentally
Page 34 of 88
Preferable Paper (EPP)
Enzyme Enzyme Bleaching
Equilibrium Moisture Content Equivalent Black Area
Esparto
Ethers Pulp
Extended Cooking Extensible Kraft External Fibrillation Extractives
Extruded Coating Fabric Press
1. 30% or more Post Consumer Recycled Content 2. TCF Bleaching 3. Forest Stewardship Council certified Forest Management for virgi n fiber sources. A protein that has the ability to direct or catalyze a chemical reaction. Bleaching technique in which cooked and oxygen-delignified chemical pulp is treated with enzymes prior to final bleaching. Allows pulp to be bleached without chlorine chemicals. The moisture content of a paper that has reached a balance with the atmosphere surrounding it, i.e. in a condition in which it will neither give up nor absorb moisture. Of a dirt speck is defined as the area of a round black spot on a white background of the TAPPI Dirt Estimation Chart which makes the same visual impression on its background as does the dirt speck on the particular background in which it is embedded. A grass from North Africa which makes a soft, ink receptive sheet.
Generally these are high purity, high viscosity pulps that are swollen in sodium hydroxide initially, followed by reaction with organic epoxides or chlorides like ethylene oxide or methyl chloride to form an organic polymer called cellulose ethers (methyl cellulose, hydroxyethyl cellulose, carboxymethyl cellulose, etc.). Cellulose ethers are used for thickening of fluids such as toothpaste, ketchup, shampoos, diet drinks and hundreds of other applications. Method of cooking pulp to low lignin content, thereby reducing the need for bleaching chemicals. Very strong virgin Kraft papers which stretches (approximately 6%) more in MD and tears less easily than regular Kraft paper. A refining action that results in partial detachment of fibrils from outer layer of a fiber. Any number of different compounds in biomass that are not an integral part of the cellular structure. The compounds can be extracted from wood by means of polar and non-polar solvents including hot or cold water, ether , benzene, methanol, or other solvents that do not degrade the biomass structure. The types of extractives found in biomass samples are entirely dependent upon the sample itself. Coating applied to paper or board using an extruder. Paper machine wet press that uses a special multiple weave fabric belt sandwiched between the regular felt and the rubber covered roll, increasing the capacity to receive and remove water from the nip between the rolls. Page 35 of 88
Falling Film Evaporator
A type of heat exchanger used for concentrating a solution consisting of a non-volatile solute and a volatile solvent; solution flows downward on the heat exchange surface by gravity; the heat exchange surface is typically a bundle of plates, lamellas or tubes; commonly used in pulp mills and chemical recovery process.
Fan-out
A dimensional change in paper associated with its passage through a printing unit. In web offset printing it is the increase in web width after each blanket impression. A high flow rate, low head pump used to pump diluted stock to paper machine headbox.
Fan Pump
Fanfold
Continuous multiple ply form manufactured from a single wide web which is folded longitudinally.
Page 36 of 88
Feathering
The tendency of liquid ink to spread along the paper fibers so that the image produced does not have sharp, clean edges.
Felt
A woven cloth used to carry the web of paper between press and dryer rolls on the paper machine.
Felt Filling
Undesirable accumulation of particulate matter within the void spaces of press felts. Surface characteristics of paper formed at the wet end of a paper machine, using woven wool or synthetic felts with distinctive patterns to create a similar texture in the finish sheets. Imprint left on the paper by one or more of the felts used in making the paper. The mark may be wanted or unwanted and special effects can be introduced in this way. The side of the paper which does not touch the wire on the paper machine. The "top side" or felt side is preferred for printing because it retains more fillers. The slender, thread-like cellulose structures that forms the main part of tree trunk and from separated and suitably treated, cohere to form a sheet of paper.
Felt Finish
Felt Mark
Felt Side
Fiber or Fibre
Page 37 of 88
Fiber Axis Ratio Fiber Coarseness Fiber Cut Fiber Debris Fiber Floc Fiber Orientation Fiberboard Fibrillation Fibrillae or Fibrils
Filler
Filter Paper
Filtrate Fines
Ratio of fiber width to fiber thickness. Weight per unit length of fiber. A fiber cut is a short, straight cut located on the edge of the web, caused by a fiber imbedded in the web of paper. Pieces of material which has been separated from the main body of the fiber. Fibers that have agglomerated as a result r esult of poor formation. Refers to the alignment of the fibers in the sheet. Board made from defibrated wood chips, used as a building board. A structural change occurring in the walls of chemical pulp fibers during beating. String-like elements that are loosened from the paper fibers during the beating process. They aid in the bonding processes when paper is being manufactured. Any inorganic substance added to the pulp during manufacturing of paper. Most of fillers are cheaper than fibers fi bers and so fillers are added to reduce the overall cost of paper. Fillers are also used to improve optical and other printability related properties. Fillers improve opacity and brightness. Fillers reduce strength properties of paper. Unsized paper made from chemical pulp, in some cases also with an admixture of rags, sometimes with a wet strength finish. Filtration rate and selectivity, which are both dependent on the number and the size of the pores, can be controlled by specific grinding of the pulps and creping.
The effluent from the washing or filtering process. Small particles fiber defined arbitrarily by classification. cl assification. Page 38 of 88
Fine Papers Finish
Finishing Finishing Broke First Pass Retention
Fish Eye Flag Flame Resistant Flat Crush of Corrugated Board
Flashing
Fly Leaf/Shaving Flexography
Flexural Rigidity
Flocculation
Uncoated writing and printing grade paper including offset, bond, duplicating and photocopying. The surface characteristic of a sheet created by either on-machine or offmachine papermaking processes. Popular text and cover finishes include smooth, vellum, felt, laid, and linen. The trimming, winding, rewinding and packing of paper rolls or trimming, cutting, counting and packing of paper sheets from parent roll. Discarded paper resulting from any finishing operation. First-pass retention gives a practical indication of the efficiency by which fine materials are retained in a web of paper as it is being formed. First-pass retention values can be calculated from just two consistency measurements, the headbox consistency, and the white water consistency. There is a very wide diversity of first-pass retention on different paper machines, from less than 50% to almost 100%. The key rules that papermakers follow are that (a) first-pass retention should have a steady value, and (b) that value should be high enough to avoid operational problems or an excessively two-sided sheet. Some operational problems that can be caused by low values of first-pass retention are increased frequency of deposit problems, filling of wet-press felts, poor drainage, and unsteady drainage rates and sheet moistures. A paper defect appearing as glazed, translucent spot caused by slime, fiber bundles, and/or improperly prepared chemical additives in the stock. A strip of paper protruding from a roll or skid of paper. May be used to mark a splice in a roll of paper or used to mark off reams in a skid. Treatment applied to kraft paper to make it resistant to catching on fire (not fire proof —will char but not burst into flame). A laboratory test (Tappi T808 or T825) of a single wall combined board specimen to measure its resistance to crushing forces from conversion and handling. Test can also be an indicator of flute formation and the presence of crushed or leaning flutes. Spontaneous boiling and cooling of a liquid caused by the reduction of pressure below the vapor pressure of the liquid. Flashing occurs in blow tank during blowing. Trim scrap from printing operation. A form of rotary letterpress using flexible rubber or photopolymer plates.
The measurement of a combined board resistance to flexing. Combined with ECT box perimeter and flute type, it is key to predicting box compression resistance or static load resistance (Tappi T566). A tendency for fibers to collect together in bunches in the presence of flow, and especially in the presence of retention aids; the same word also refers to the action of high-mass polymers in forming bridges between suspended colloidal particles, causing strong, relatively relativ ely irreversible agglomeration. Page 39 of 88
Flotation Cell
Main equipment of Flotation Deinking, Deinking, Large number of tiny air bubbles are injected into the cleaned pulp, the free ink particles attach themselves to these bubbles and float to the surface where it is skimmed off and removed.
Flotation Deinking
Using flotation method for removing ink from paper during the de-inking process. Non contacting dryer used in pulp drying or coating applications, drying is achieved by passing sheet between two dryer hoods where hot dry air is impinged onto the sheet and the moisture is evaporated and removed by an air system. Front end of the paper machine whose objective is to distribute the papermaking fiver uniformly across the machine from back to front. A chemical, mechanical or combination of chemical/mechanical pulp, usually bleached, used as an absorbent medium in disposable diapers, bed pads and hygienic personal products. Also known as "fluffing" or "comminution" pulp.
Flotation Dryer
Flowspreader Fluff Pulp
Fluorescent Dye Fluorescent Inks
Fluorescent Whitening Agent
Flute
A coloring agent added to pulp to increase the brightness of the paper. It may give a slight blue or green cast to the sheet. Printing inks that emit and reflect light. Generally, they are brighter and more opaque than traditional inks, but they are not color fast, so they will fade in bright light over time. Their metallic content will also affect dot gain and trapping. Also referred to as an "optical brightener." A chemical compound when expose to a light containing an ultraviolet component will absorb and reemit light in the blue spectrum or in other words fluoresce. FWA's will enhance brightness and blueness quality of white paper. One of the wave shapes pressed into corrugated medium. Flutes are categorized by the size of the wave. A, B, C, E and F are common flute types, along with a variety of much larger l arger flutes and smaller flutes. fl utes.
Page 40 of 88
Fluted Edge Crush Flute (A,B,C,E,F&G)
Measures the edgewise compression strength of corrugating medium using a fluted test specimen per Tappi T824. These letters define the type of corrugated material in terms of the number of corrugations per unit length and the height of the corrugations specifically these are: Flute
Fluting Foamboard Foil or Hydrafoil
Corrugations per meter
Height of corrugation (mm)
A
105 – 125
4.5 - 4.7
B
150 – 185
2.1 - 2.9
C
120 - 145
3.5 - 3.7
E
290 - 320
1.1 - 1.2
F
410 - 420
0.7 - 0.8
G
550 - 560
0.5 - 0.6
Waves or corrugation in heat-set web offset prints that runs in the press direction. C1S paperboard designed for lamination to a foam backing for point-ofpurchase displays, posters, and signs. The flat strip used to support wire. Only the leading edge of the wire touches the foil. Foil helps in removing water by creating gentle suction and also doctor the water removed in previous section.
Page 41 of 88
Folding
Folding Boxboard
Folding Strength or Folding Endurance
Formation
Forming Board
Fortified Rosin Size Fountain Roller Four-color Printing Process
Doubling up a sheet of paper so that one part lies on top of another. Folding stresses the paper fibers. To create a smooth, straight fold, heavy papers like cover stocks and Bristol need to be scored before they're folded. Single or multi-layer paperboard made from primary and/or secondary fibers, sometimes with a coated front, used to make consumer packaging (cartons). Folding strength is most important in currency paper. Multiple fold strength is also important for paper used in books, maps, and pamphlets. It's far less important in one-fold greeting cards or envelopes, where fold cracking is the vital consideration. Folding endurance or strength is measured and reported in numbers. The dispersion of fibers in a sheet of paper. The more uniform and tightly bound the fibers, the better the sheet will print and look. Close Formation Uniform distribution of fibers. Cloudy formation: A spotty, non-uniform dispersion of fibers, the opposite of close formation. Forming Board is the leading forming unit under the fabric closest to the slice. The stock jet velocity, the impingement angle and the position of the impingement onto the forming board will determine the water removal and the activity produced at this point. Modern Forming Boards are stepped to create activity at high speeds – this greatly enhances the formation.
The roller on a printing machine which initiates the supply of moisture to the damping system. The roller on a printing machine which initiates the supply of moisture to the damping system. A printing method that uses dots of magenta (red), cyan (blue), yellow, and black to simulate the continuous tones and variety of colors in a color image. Reproducing a four-color image begins with separating the image into four different halftones by using color filters of the opposite (or negative) color. For instance, a red filter is used to capture the cyan halftone, a blue filter is used to capture the yellow halftone, and a green filter is used to capture the magenta halftone. Because a printing press can't change the tone intensity of ink, four-color process relies on a trick of Page 42 of 88
the eye to mimic light and dark areas. Each halftone separation is printed with its process color (cyan, magenta, yellow, and black). When we look at the final result, our eyes blend the dots to recreate the continuous tones and variety of colors we see in a color photograph, painting, or drawing.
Fourdrinier
Named after its inventor, the Fourdrinier papermaking machine is structured on a continuously moving wire belt on to which a watery slurry of pulp is spread. As the wire moves, the water is drained off and pressed out, and the paper is then dried.
Free Stock
Unrefined stock. Stock that, when drained under gravity, parts easily with the water of suspension A term used to define how quickly water is drained from the pulp. The opposite of freeness is slowness. Freeness or slowness is the function of beating or refining. Freeness and slowness reported in ml CSF and degree SR respectively are also the measurement of degree of refining or beating. Paper that is free of mechanical wood pulp, which is true of virtually all fine printing papers. A sheet printed on one side and folded first vertically and then horizontally to produce a four-page folder.
Freeness
Freesheet French Fold
Fully Bleached Pulp
Pulp that has been bleached to the highest brightness attainable (> 60 ISO). Page 43 of 88
Furnish Fuzz
A blend of fibers, pigments, dyes, fillers and other materials that are fed to the wet end of the paper machine. Fibrous projections on the surface of a sheet of paper, caused by excessive suction, insufficient beating or lack of surface sizing. Lint appears in much the same manner but is not attached to the surface.
Gampi
A bast fiber from the gampi tree used in Japanese papermaking to yield a smooth, strong sheet.
Gatefold
Two or more parallel folds on a sheet of paper with the end flaps folding inward.
Ghosting
Variation in ink gloss, density or color that are not part of the original design, but appear as a repeat or ghost image associated with another area of the copy.
Page 44 of 88
Glassine Paper
A translucent paper made from highly beaten chemical pulp and subsequently supercalendered.
Glazed Paper
Paper with high gloss or polish, applied to the surface either during the process of manufacture or after the paper is produced, by various methods such as friction glazing, calendering, plating or drying on a Yankee drier.
Gloss
The property that's responsible for a paper's shiny or lustrous appearance; also the measure of a sheet's surface reflectivity. Gloss is often associated with quality: higher quality coated papers exhibit higher gloss. Blotchiness or non-uniformity in the paper's gloss (unprinted or printed). Typically only visible at certain viewing angles. Usually attributable to poor formation and heavy calendering. Papers are differentiated from each other by their grade. Different grades are distinguished from each other on the basis of their content, appearance, manufacturing history, and/or their end use. The direction in which most fibers lie in a sheet of paper. As the pulp slurry moves forward on the papermaking machine's formation wires, the fibers tend to align themselves in the direction of movement. Binding books parallel to the grain allows for a smoother fold then working across the grain. Grain direction of sheet fed papers is usually indicated by underlining the number, e.g., 23" X -35". On a web press, the grain direction should run along the length of the paper web. Grain running lengthwise along a sheet of paper. Grain running widthwise along a sheet of paper. Weight in grams of one square meter of paper or board (g/m 2); also basis weight. Uneven staining of fibers in pulp, usually due to a very high affinity of dye for fiber, together with insufficient dilution and/or poor mixing.
Gloss Mottle
Grade
Grain
Grain Long Grain Short Grammage Granting
Page 45 of 88
Gravure
A printing process that uses intaglio, or recessed, image carriers. The image carrier, which is flat or cylindrical, moves through an ink pool. A blade scrapes excess ink off the plane of the plate, leaving ink in the recessed wells. A second cylinder presses the paper onto the plates, where it picks up ink from the wells. The high speed of gravure presses and the durability of the metal intaglio plates make gravure an economical printing method suitable for large print runs (more than two million copies).
Gravure Paper
Paper for gravure printing that has very low print roughness and good wettability of gravure inks. A homogeneous board made usually of mixed waste papers with or without screenings and mechanical pulp on a continuous board machine, in thickness less then 1 mm. A protective wrapping paper made from chemical wood pulps, which are highly hydrated in order that the resulting paper may be resistant to oil and grease.
Gray Board
Greaseproof Paper
Greenfield Mill Green House Gases
Green Liquor Green Paper
Mill or production facility built on undeveloped site. Gases that provide an insulating effect in the earth's atmosphere, potentially leading to global climate change. These gases include carbon dioxide, methane, nitrous oxide, ozone, and water vapor. The liquor that results when the inorganic smelt from the recovery furnace is dissolved in water is called "green" liquor. Immature paper which has not been conditioned or had the opportunity to mature naturally. Page 46 of 88
Grinder
A machine in which logs are defibrated against a revolving grindstone.
Groundwood Papers
A general term applied to a variety of papers made with substantial proportions of mechanical wood pulp together with bleached or unbleached chemical wood pulps (generally sulfite), or a combination of these, and used mainly for printing and converting purposes. A mechanically prepared (by grinding wood logs against a rough surfaced roll rotating at very high speed) coarse wood pulp used in newsprint and other low cost book grades where it contributes bulk, opacity, and compressibility. Groundwood pulp is economical since all the wood is used; however, it contains impurities that can cause discoloration and weakening of the paper. A natural polymer that is used as a dry-strength additive, often as a cationic derivative. A machine used to trim stacks of paper, which works the same way the original French guillotine worked. A cutting blade moves between two upright guides and slices the paper uniformly as it moves downward.
Groundwood Pulps
Guar Gum Guillotine
Page 47 of 88
Gurley Porosity
A method to measure the air permeability of paper by TAPPI method T536.
H Factor
It is the area under the curve when relative reaction rate is plotted against cooking time. The half fold is commonly used for brochures and greeting cards. For cover weight paper, a score is usually required to produce a smooth folded edge. This fold is perfect for newsletters. An 11" x 17" sheet folded this way has only one open side and fits into a #10 envelope. The newsletter looks good and is easy to handle. Picture with gradations of tone, formed by dots of varying sizes in one color.
Half Fold Half + Letter Fold
Half Tone
Handmade Paper
A sheet of paper, made individually by hand, using a mould and deckle.
Hard Cook
Undercooked pulp with respect to target conditions. Page 48 of 88
Hard Pulp Hard Sized Paper Hardwood
Head Box or Flow Box or Breast Box
Chemical pulp with a high lignin content. Paper treated with high degree of internal sizing. Wood from trees of angiosperms class, usually with broad leaves. Trees grown in tropical climates are generally hardwood. Hardwood grows faster than softwood but have shorter fibers compared to softwood. The part of the paper machine whose primary function is to deliver a uniform dispersion of fibers in water at the proper speed through the slice opening to the paper machine wire.
Heart Wood
The dark colored , center of a tree trunk, consisting of dormant wood.
Heat Embossing / Thermography
Heat embossing is done with embossing powder and a heat tool. The powder becomes liquid when heated and then quickly dries hard when it cools. The end result of heat embossing is a raised surface on the paper. This process is actually called "thermography" in the printing world.
Page 49 of 88
Heat Set Web
Heat Transfer Paper Hemicellulose
Herbaceous Plants Hickey
High Finish Hog Fuel Hold Out
Holocellulose Hologravure Hood
Hot Melt Hot Groundwood Pulp Hydration Hydrogen Peroxide Bleaching
An offset printing process done on a web of paper supplied in a roll. The term heat set originates from the inks used in the process. They contain high amounts of solvent flashed off in ovens to dry at very high speeds. Web presses perfect or print both sides of the sheet si multaneously. The paper used in Thermal transfer printing (Sublimation printing). A constituent of woods that is, like cellulose, a polysaccharide, but less complex and easily hydrolysable.
Non-woody species of vegetation, usually of low lignin content such as grasses. An irregularity in the ink coverage of a printed page. Hickeys are caused by paper or pressroom dust, dirt, or pick out on the printing blanket, all of which prevent the ink from adhering to the paper surface. Smooth finish applied to paper to improve the printing surface. A mixture of bark and other wood waste usually produced by sawmills; burned to produce energy and steam. Resistance of paper surfaces to the absorption of ink. High Hold Out offers higher resistance to ink absorption. Regular Hold Out allows greater ink absorption. The total carbohydrate fraction of wood — cellulose plus hemicellulose. Printining process by which great continuous 3D depth is achieved using textures and patterns. A hood covering the paper machine drying section and designed for moist air removal.
A type of glue or adhesive applied while hot/warm. Mechanical pulp produced by grinding logs that have been pre-treated with steam. The prolonged beating or refining of cellulose pulp in water to reduce it to a semi-gelatinous mass. A method in which pulp is bleached in an alkaline environment with hydrogen peroxide (H2O2), sometimes using oxygen reinforcement. The method considerably reduces the need for chlorine-containing chemicals in the final bleaching of chemical pulps. Page 50 of 88
Hydrophilic Hydrophobic Hydropulper
Having strong affinity for water. Lacking affinity for water. An equipment used to slush broke/paper in to pulp.
Hygroscopic
Having the property to absorb water vapor from the surrounding atmosphere. Most of the papers (except glassine, greaseproof or wet strength etc.) are hygroscopic in nature.
Imbibition
The absorption of liquid by a fiber without a corresponding increase in volume. Process of treating a sheet of paper with a chemical or wax so that the treatment penetrates into the paper. The cylinder or flat bed of a printing press that holds paper while an inked image from the blanket is pressed upon it. Semi-genuine watermark made in the paper machine press section using engraved rolls while the web is still wet. A stiff, inexpensive paper with a smooth finish. The high bulk but low weight of this paper makes it a popular choice for business reply cards. Greenhouse gas emissions relating to an industrial process but not directly generated by it. Measurement of such emissions, as per the World
Impregnation Impression Cylinder Impression Watermark Index Paper Indirect Greenhouse Gases
Resources Institute’s Scope 2 definition, is commonly limited to those
Industrial Papers
Infra Red Drying Ink
Ink Absorption Ink Coverage
Ink Holdout Ink Jet Printing
associated with purchased energy. A very general term, which is used to indicate papers manufactured for industrial uses as opposed to cultural purposes. Thus, building papers, insulating papers, wrapping papers, packaging papers, etc. would be considered industrial papers. Electric or gas infra red dryers used to initially achieve immobilization of the fluid coating and commence the drying process. Printing inks are made up of pigment, pigment carrier and additives formulated to reduce smudging, picking and other printing problems associated with ink. The choice of ink depends on the type of paper and printing process. A paper's capacity to accept or absorb ink. The portion of the total surface area of the paper which is covered by ink. The portion of the coverage usually is expressed in terms of percent of ink coverage. The way the ink pigment sits on the surface of the paper. Strong ink holdout results in a sharp, bright image. Printing process of an image or text by small ink particles projected onto the paper surface. Page 51 of 88
Ink Tack Insect Resistant Insider Liner
Insulating Board
Intaglio
The body or cohesiveness of ink. The measure of tack as the force required to split an ink film. Paper treated with insecticide compounds to make it resistant to insect attack. The liner bonded to the medium at the single facer. Called inside liner because it is the inside facing of a corrugated box. Also called the single face liner. A type of board composed of some fibrous material, such as wood or other vegetable fiber, sized throughout, and felted or pressed together in such a way as to contain a large quantity of entrapped or "dead" air. It is made either by cementing together several thin layers or forming a nonlaminated layer of the required thickness. It is used in plain or decorative finishes for interior walls and ceilings in thickness of 0.5 and 1 inch (in some cases up to 3 inches) and also as a water-repellent finish for house sheathing. Desirable properties are low thermal conductivity, moisture resistance, fire resistance, permanency, vermin and insect resistance, and structural strength. No single material combines all these properties but all should be permanent and should be treated to resist moisture absorption. A method of printing in which an image or letter is cut into the surface of wood or metal, creating tiny wells. Printing ink sits in these wells, and the paper is pressed onto the plate and into the wells, picking up the ink. 1. Gravure is considered an intaglio printing process. 2. In papermaking, watermarking from countersunk depressions in the dandy roll to provide a whiter or denser design instead of increased transparency.
Integrated mill Intermittent Board Machine
Internal Bonding Strength Internal Fibrillation Internal Sizing International Paper and Board Sizes
A mill which starts with logs or wood chips and first produces wood pulp which it then processes to make paper or board. A machine for producing sheets of thick board by winding the web formed on a Fourdrinier wire or cylinder mould (s) around a making roll to form a sheet consisting of several layers. When the thickness is sufficie nt the layers are cut, so forming a sheet which is removed from the machine for drying and any further processing. Determines how strongly the coating is fused to the body stock. Caused by long periods of hydration, paper with high internal bonding strength resists picking during the printing process. Loosening of internal bond within a fiber. Occurs when sizing materials are added to the water suspension of pulp fibers in the papermaking process. Also known as Beater, or Engine sizing. Also known as ISO sizes are widely used in metric countries. ISO standards are based on a rectangle whose sides have a ratio of one to the square root of 2 (1.414). No matter how many times a sheet of these proportions is halved, each will retain the same constant proportions. There are three ISO series A, B, and C. The A Series: The A series is for general printed matter including stationary and publications. SIZE Millimeters 4A0 1682 x 2378
Page 52 of 88
2A0 1189 x 1682 A0 841 x 1189 A1 594 x 841 A2 420 x 594 A3 297 x 420 A4 210 x 297 A5 148 x 210 A6 105 x 148 A7 74 x 105 A8 52 x 74 The B series: The B series is about half way between two A sizes. It is intended as an alternative to the A series, used primarily for posters and wall charts. SIZE Millimeter B0 1000 x 1414 B1 707 x 1000 B2 500 x 707 B3 353 x 500 B4 250 X 353 B5 176 x 250 B6 125 x 176 B7 88 x 125 B8 62 x 88 B9 44 x 44 B10 31 x 44
The C series: The C series is used for folders, post cards and envelopes. C series envelope is suitable to insert A series sizes. SIZE Millimeter C0 917 x 1297 C1 648 x 917 C2 458 x 648 C3 324 x 458 C4 229 x 324 C5 162 x 229 C6 114 x 162 C7 81 x 114 C8 57 x 81
RA Series Formats RA0 860 x 1220 RA1 610 x 860 RA2 430 x 610 RA3 305 x 430 RA4 215 x 305 SRA Series Formats SRA0 900 x 1280
Page 53 of 88
SRA1 640 x 900 SRA2 450 x 640 SRA3 320 x 450 SRA4 225 x 320
ISO Brightness Ivory Board
Jet to Wire Speed Ratio
Job Lot
Jog
Jumbo Roll
Envelopes DL 110 x 220 C6 114 x 162 C5 162 x 229 C4 229 x 458 C3 324 x 458 The brightness of paper and board measured at a wavelength of 457 nanometers under standard conditions. High-quality board made in white or colors with a bright, clear appearance, particularly used for visiting cards and similar high-class printed work. Original Ivory Board was and still is made in Holland, although the grade is made in many countries.
Papermakers adjust the jet-to-wire speed ratio to fine-tune the paper structure. The "jet" is the narrow stream of dilute stock that comes out of the headbox slice opening. The "wire" is the continuous belt of forming fabric. Often it is possible to improve the uniformity of paper by running jet-to-wire speed ratio as one. "Rushing the sheet" means that the jet speed is higher than the wire speed. "Dragging the sheet" means that the wire speed is higher than the jet speed. Especially in the case of dragging, increasing values of jet-to-wire speed ratio tend to align fibers in the machine direction. For square sheet (paper which has same strength properties in CD and MD), jet to wire ratio should be kept as close to one as possible. Out of specification, defective or discontinued types of paper made in small quantities for special orders and sometimes sold at lower than regular prices. To shake a stack of papers, either on a machine or by hand, so that the edges line up. Finisher jog the paper to remove any improperly cut sheet. Printers jog the paper to get rid of any dust or particles and to ensure proper feeding into the press. A roll of paper, direct from the paper machine, wound on a machine winder spool as distinct from rolls that have been slit and rewound on cores.
Page 54 of 88
Kaolin Kappa Number
Kenaf
Kiss Impression Knotter Knotter Pulp Kozo
Kraft Bag Paper
White clay used as an additive and filler in paper and coating made up chiefly of minerals of the kaolinite type. A term used to define the degree of delignification. Modified permanganate test value of pulp which has been corrected to 50 percent consumption of the chemical. Kappa number has the advantage of a linear relationship with lignin content over a wide range. Kappa Number x 0.15% = % lignin in pulp An annual agricultural plant, native of India, which has along fiber in the bark that, is suitable for papermaking.
The lightest impression (anilox and plate to substrate) possible to properly reproduce the image on paper. Vibratory screens used for separating knots, uncooked chips and shives from the pulp at the blow tank. Pulp made from the rejects from chemical pulp screening. The most common fiber used in Japanese papermaking, it comes from the mulberry tree. It is a long, tough fiber that produces strong absorbent sheets.
A paper made of sulfate pulp and used in the manufacture of paper bags. It normally has a greater bulk and a rougher surface than the usual kraft wrapping paper. Page 55 of 88
Kraft Paper
Kraft Pulp
Kraftliner
Label
Label Paper
Laid
Laid Lines Laminated Paper
Laminated Linerboard Laminator
Lapping Machine Laser Printing
Latency
A paper of high strength made from sulfate pulp. Kraft papers vary from unbleached Kraft used for wrapping purposes to fully bleached Kraft used for strong Bond and Ledger papers. Chemical wood pulp produced by digesting wood by the sulfate process (q.v.). Originally a strong, unbleached coniferous pulp for packaging papers, kraft pulp has now spread into the realms of bleached pulps from both coniferous and deciduous woods for printing papers. Paperboard of grammages of 120g and more, generally made from bleached or unbleached sulfate pulp and used as an outer ply in corrugated board. A separate slip or sheet of paper affixed to a surface for identification or description. For fiberboard boxes, includes: Full Label, Mailing or shipping Label, Spot Label and UPC (Universal Product Code) Label. Mostly one-side coated papers which must be printable in 4-colour offset and gravure printing. These papers are usually suitable for varnishing, bronzing and punching and sometimes also feature wet strength and alkali resistance (See "Wet strength and alkali resistant paper") in order to ensure the removal of the labels e.g. in the bottle rinsing machines of breweries A finished produced with a dandy roll having closely spaced wires.
A continuous watermark consisting of very close parallel lines, generally associated with spaced lines (chain lines) at right angles to these. A paper built up to a desired thickness or a given desired surface by joining together two or more webs or sheets. The papers thus joined may be alike or different; a totally different material, such as foil, may be laminated with paper. Two or more plies of linerboard adhered to one another for increased structural stability. A machine that adheres multiple plies of paper or fiberboard. May be used to adhere full labels to a facing, or, for enhanced structural properties, multiple facings, corrugating mediums or sheets of com bined board. A wet machine on which folded wet pulp sheets are produced from screened pulp for storage and/or shipment. Xerographic printing where a modulated laser ray is projected on to a photoconductive cylinder or belt by a rotating mirror. The laser serves to product the electrostatic latent image, which is developed with toners. The curl and spiral of individual pulp fiber created during refining specially in thermomechanical pulping process Page 56 of 88
Latency Chest
Layboy Leachate Lead Dryer or Baby Dryer Leaf Fibers Ledger Paper Letter Fold
Letter Press Lick Coating
Light fastness Light Weight Coating (LWC) Light Weight Paper Lignin
Lignocellulose Like-Sided
A storage chest after the second stage refining in thermo-mechanical pulping process in which pulp is agitated and stored at a specified temperature for a predetermined time to remove latency. A device at the end of cutter for jogging sheets in to a square pile. Water that has as a component of dissolved matter accumulated as a result of passing through material. e.g. rain water passing through waste dump. A small diameter dryer just after the press section. Papermaking fibers coming from the leaves of the plant such as hemp, manila, flax, sisal etc. A strong paper usually made for accounting and records. It is similar to Bond paper in its erasure and pen writing characteristics. This common fold, used for mailings and brochures, is much like a letter folded by hand for inserting in an envelope. The letter fold produces a selfcontained unit, easily handled by automated envelope inserters. A process of printing in which raised images are coated with ink and pressed directly onto a paper or paperboard surface A light form of mineral coating, achieved by supplying the surface sizing press of the paper making machine with coating material instead of normal surface sizing solution. The speed at which a pigment or colored paper fades in sunlight. or How permanent a color is or how unaffected by light it is. 2 Coating applied at 7-10 g/m on one or both sides of the paper. Papers having a grammage (basis weight) normally less than 40 g/m2. A complex constituent of the wood that cement the cellulose fibers together. Lignin is brown in color. Lignin is largely responsible for the strength and rigidity of plants, but its presence in paper is believed to contribute to chemical degradation. To a large extent, lignin can be removed during manufacturing.
Refers to plant materials made up primarily of lignin, cellulose, and hemicellulose. Paper that has the same appearance and characteristics on both sides. Page 57 of 88
Lime Sludge or Sludge
Sludge of calcium carbonate (CaCO3) formed during preparation of white liquor in the chemical recovery process.
Linen Finish
A finished paper that has an overall embossed pattern on the surface resembling the look and feel of linen cloth, and one manufactured with engraved embossing rolls.
Liner
A creased fiberboard sheet inserted as a sleeve in a container and covering all side walls. Used to provide extra stacking strength or cushioning. Also used as a short hand for "linerboard" or facing." The inner and outer layers of paper that form the wall of a corrugated board. The number of lines in an inch, as found on the screens that create halftones and four-color process images (for example, "printed 175-line screen"). The more lines per inch, the more detailed the printed image will be. With the demand for computer-generated imagery, the term "dots per inch" (which refers to the resolution of the output), is replacing the term "lines per inch." Loosely bonded fibers at the paper surface that attached to the plate or blanket of the printing machine. A generic term for any printing process in which the image area and the non-image area exist on the same plate and are separated by a chemical repulsion. Usually oil based offset printing. Addition of fillers A heated room in which wet sheet of paper/paperboard are hang on poles. This old method of drying is known as loft drying or pole drying.
Linerboard Lines Per Inch (LPI)
Lint Litho
Loading Loft Dryer
Page 58 of 88
Log Logging Long Log Look Through
A piece of pulpwood length cut from trees to convenient size for storage, transportation and handing. The operation of harvesting trees from woodlands, processing in to barked/unbarked logs or chips. A whole length pulpwood before cutting to shorter l og. The appearance of the paper when held up to transmitted light. It discloses whether the formation is even and uniform or lumpy and ‘wild’. For book
Loose Winding Lumen
publishing papers, a regular, even look through is desirable, indicating a well made, uniform sheet. A paper roll winding defect caused by insufficient sheet tension during winding. The center void portion of a cellulose fiber.
Lump
An incomplete separation of fiber bundling or coming together of fibers and other papermaking materials, causing raised, hard and localized spots in the sheet.
M Weight
The weight of one thousand sheets of paper, any size; or double the ream weight. A measure of the surface area of paper/paperboard which is obtained from a ton of paper. Usually the last large chest or tank that contains thick-stock pulp before it is made into paper. Fabrics of various types employed on the paper machine to carry the web and perform other functions. It includes the machine wire, dandy roll cover, press felts and dryer felts etc., which may be composed of natural or synthetic materials. Crepe paper produced on the paper machine, and not as a secondary option. The direction of the web through the paper machine. Finished produced on the paper as it leaves either the machine or the calender stack. For increased printability, or smoothness when used as a liner, etc. Machine glazed. Paper with a glossy finish on one side produced on the paper machine by a Yankee cylinder. The rate at which paper machine runs, expressed as m/min or ft/min. Width of the paper web in the paper machine. A light weight bond paper used for making carbon or manifold copies or for airmail correspondence. A semi-bleached chemical sulfate paper. Not as strong as Kraft, but have better printing qualities.
2
M Yield/Ton Machine Chest Machine Clothing or Paper Machine Clothing Machine Crepe Machine Direction Machine Finish
Machine Glazed Machine Speed Machine Width Manifold Paper Manila
Page 59 of 88
Manufacturing Order Market Pulp Marbling Matte Finish Maximum Trimmed Width
Mechanical Paper
Mechanical Pulp
Medium Density Fiberboard (MDF) Mesh Metamerism MG Machine
Micro Crystalline Cellulose Pulp Mil Mill
Also known as making order. A quantity of paper manufactured to custom specifications, such as a special weight, color, or size not available as a standard stocking item. Pulp which is made to be used elsewhere for the production of paper. Usually dried to reduce freight costs but may be "wet lap" ( 50% water). Addition of strongly stained fibers to the stock to give the paper a marbled appearance. A dull, clay-coated paper without gloss or luster. The greatest width of usable paper that is possible to make on a given paper making machine, i.e. the full width less the necessary trim to give clean edges. There is 3-10% width shrinkage (depending on freeness of stock) in dryers. It is not possible to specify sizes which, in aggregate, exceed this width. This paper contains mechanical pulp, thermomechanical pulp (TMP) or chemithermo-mechanical pulp (CTMP) and also chemical pulp. The shares of chemical and mechanical pulp vary depending on the application. Highly mechanical papers such as newsprint tend to yellow more rapidly if exposed to light and oxygen than woodfree papers so that they are mainly used for short-lived products. In printing papers the mechanical pulp improves opacity. Pulp produced by mechanically grinding logs or wood chips. It is used mainly for newsprint and as an ingredient of base stock for lower grade printing papers. A composite panel made from wood fibers and resin and formed under pressure and heat. MDF has a smooth surface and good machinability, and is used for furniture, cabinetry and millwork. Count of wires per inch for metal and/or plastic screen used in paper mill. The tendency of color to appear different under different light sources such as fluorescent or natural sunlight. A paper machine incorporating a Yankee or a MG drying cylinder in the drying section to produce MG paper.
Like Ethers Pulps, these pulps are used in thickening and pharmaceutical applications, particularly in construction of tablets and other non-capsular pills. One thousandth of an inch. The physical site where paper is manufactured; also refers to a company that manufactures paper. Page 60 of 88
Mill Broke
Millboard
Paper generated at the paper mill prior to completion of the manufacturing process. Wet mill broke originates at the wet end of the papermaking machine, while dry mill broke comes from the dry end of the papermaking machine. A thick, dense, homogeneous board, for book production, made generally from wastepaper, on a special board making machine one sheet at a time. Used in binding case bound books, ledgers etc. as binders’ boards.
Mineral Filler Mitsumata
Materials such as chalk and china clay that are added to paper in order to change its density or improve its surface and optical properties. A bast fiber used in Japanese papermaking that yields a soft, absorbent and lustrous quality.
Mixed Office Waste
Wastepaper generated from offices, such as letters, memos, invoices, etc. which are collected and sorted for paper qualities. This is the major source of post consumer fiber.
Modified Starch
Papermaking starch that has been processed generally by oxidation, to achieve lower viscosity or chemical characteristics which are beneficial in use as an additive in papermaking. The amount of moisture or water in a sheet of paper, expressed in percent. 6 to 7% is desirable. Paper Treated with asphalt, wax, plastic, etc. to control penetration of moisture. Pulp, which is used for producing pulp-based or fibrous products by pressing; example products: egg packages, trays and boxes for fruits and vegetables.
Moisture Content Moisture Resistant Molding Pulp
Page 61 of 88
Mordant Mottle
Mottling Fiber Mullen Multi-stage Cooking Multiply Board Machine Multiply Paper Making Process
Native Lignin Neutral Detergent Fiber (NDF) Newsprint Nip
Nitration Pulps
Non Wood Fibers Nonwoven
Odd Lot Off-machine Coating Off-machine Creping
Chemical added to pulp to improve the fixation of dyes to the fiber. A random non-uniformity in the visual density, color or gloss of a printed area; also known as orange peel, back-trap mottle, wet-trap mottle, pigment flocculation, striations, etc. Heavily dyed fibers added to a different color stock furnish to produce characteristic surface effects. Measurement of the force required, in pounds per square inch, to rupture a sheet of kraft paper. Also known as bursting strength. Chemical pulping process in which the alkalinity of the cooking liquor is varied by charging the alkali in several stages. A machine in which a number of plies of paper can be combined together in the wet state to produce thick paperboard. A paper/board making process in which different layers of fibers are deposited one over the other to form the sheet. The multiply process is used to make the optimum use of various type of fibers available. It is also used to make heavy basis weight papers. The lignin as it exists in the lignocellulosic complex before separation. Organic matter that is not solubilized after one hour of refluxing in a neutral detergent consisting of sodium lauryl sulfate and EDTA at pH 7. NDF includes hemicellulose, cellulose, and lignin. A paper manufactured mostly from mechanical pulps specifically for the printing of newspaper. Point where two rolls on the paper machine come in contact.
High purity pulps that are reacted with nitric acid to form a class of chemical derivatives called cellulose nitrates. Cellulose nitrates are used in applications ranging from solvents to smokeless (gunpowder) propellants. Papermaking fibers derived from plants other than trees such as cotton, hemp, bagasse, jute, bamboo or straws. Fabric-like material made from long fibers, bonded together by chemical, mechanical, heat or solvent treatment. Off standard paper. Also the term used for side rolls or sheet left after cutting standard size/order. Coating of paper on a separate coating machine. A method whereby paper is creped in a separate operation rather than by the paper machine's Yankee cylinder. Page 62 of 88
Offset Paper
Offset Printing Old Corrugated Container (OCC)
On Machine Coating Optical Brightener Opacity
Open End Envelope Optical Brightness
Optical Whitener Orange Peel Organosolv Pulping Out of Square
Out Turn Sheet Oven Dry Moisture Content Oxygen Bleaching Oxygen Delignification Ozone (O3) Ozone Bleaching
Also known as book paper. General description of any paper primarily suited for offset printing. Can be coated or uncoated. Characterized by strength, dimensional stability, lack of curl and freedom from foreign surface material. Finish can be vellum or smooth. Also know as web offset or lithography. Offers highest degree of precision, clarity, and quality. Brown boxes that have been used for their intended purpose, then collected for recycling.
Application of coating to the paper off the paper machine, or as a separate operation to the papermaking. Fluorescent dyes added to paper to enhance the visual brightness; the dye absorbs ultraviolet light and re-emits it in the visual spectrum. That properties of paper which minimizes the "show-through" of printing from the backside or the next sheet. The higher the opacity the less likely that the printing on one side will be visible from the other side. An envelope that opens on the short dimension. Optical brighteners or fluorescent dyes are extensively used to make high, bright blue - white papers. They absorb invisible ultraviolet light and convert to visible light, falling into the blue to violet portion of the spectrum, which is then reflected back to our eyes. A dye that is added to the fiber stock or applied to the paper surface at the size press to enhance its brightness. A type of sheet surface that looks like orange. Pulping method using organic solvent, e.g. organic acid or alcohol, as delignification/cooking chemical. Paper which is trimmed improperly so the corners are not true 90 degrees. This will result in difficulty when the presser does not have a good guide edge to work from for accurate register. A sheet of paper, taken during manufacture, serving as a reference for the mill or client. The percentage loss in weight of a paper specimen when dried to constant weight in an oven maintained at the temperature of 105 +/- 2 C. A process in which pulp is initially treated with oxygen followed by 4-5 bleaching stages. A process in which oxygen gas and sodium hydroxide are used to remove lignin from brown stock. A highly reactive gas with molecules made up of three oxygen atoms. A process that uses ozone to whiten cellulose fibers following the Kraft pulping and oxygen delignification processing. Page 63 of 88
Packaging Paper Pallet
A paper or paperboard used for wrapping or packing good. A platform with a slatted bottom, used to hold and ship cartons of paper stacked on top of each other. A standard amount of paper that fits on a wooden pallet. In cut-size sheets, a pallet equals 40 cartons.
Paper Paperboard
Papermaking
Paper Cut
Paper-ink Affinity
Paper Surface Efficiency (printing)
A homogeneous sheet formed by irregularly intervening cellulose fibers. A heavy weight, thick, rigid and single or multi-layer sheet. What differentiates paperboard from paper is the weight of the sheet. If paperboard is very heavy it is called Board . Paper heavier than 150 gram per meter square are normally called Paperboard and paperboard heavier than 500 gram per meter square are called board. Invented in China by T'sai Lun some 2,000 years ago, papermaking still follows the same basic procedures. Today wood chips are cooked with chemicals to release cellulose fibers and dissolve lignin, then washed to remove impurities. Most printing papers are then bleached to lighten the color of the pulp. Pulp is mechanically and chemically treated to impart certain desired characteristics such as strength, smoothness and sizing. Large quantity of water is added to uniformly distribution of fibers and additives. The resulting slurry, which is 99 to 99.5% water, is cascaded onto the continuously moving forming fabric of the Fourdrinier paper machine. Side-to-side shaking distributes the slurry, forming a tangled web of fiber as the water drains off. A wire mesh roll called a dandy roll, moves over the surface to modulate the turbulence and smooth the topside of the paper. A felt blanket absorbs more water from the paper and sends the sheet on through a channel of hot metal drums that dry and press the paper at the same time to give it a more even-sided finish. At this point the paper is fully dry and ready for off-machine processes such as coating, embossed finishes and supercalendering. The excruciating, often unforeseeable, and usually invisible-to-the-nakedeye cut received when skin slides along the edge of a piece of paper at just the wrong angle. The tendency for paper and ink to attract and stay attracted to each other. This keeps the ink on the paper and off the reader's hands or the next sheet. An incompatibility between ink and paper can cause printing problems. Measure of the printability of a sheet of paper which is dependent upon the amount of ink the paper absorbs, the smoothness of its surface, and the evenness of its caliper. Page 64 of 88
Papeterie Papyrus
Parchment Parchmentization Parenchyma Particulate Peel Strength
Permeability Perfecting Press
Permanent Paper
Permanence
Permanganate Number (K Number) Permeability Pernicious Contraries
A paper used for greeting cards, stationery, etc…which is distinctive from
regular stock in that special watermarks and embossing may be used. The Egyptians used this aquatic plant to create a writing sheet by peeling apart the plant's tissue-thin layers and stacking them in overlapping, crosshatched pieces to form a sheet. Despite giving us the word "paper," papyrus is not a true paper. Animal skins or linings stretched and prepared as writing/painting surfaces. Produces a smooth, buttery surface. Method of treating a paper sheet with sulfuric a cid to make it greaseproof. Method of treating a paper sheet with sulfuric a cid to make it greaseproof. Airborne solid impurities such as those present in gaseous emissions (sodium sulfate, lime, calcium carbonate, soot). The amount of normal force required to delaminate a multiply paper. Strength measured by TAPPI useful method UM808 or other similar methods. Degree to which a fluid (gas or liquid) permeates or penetrate a porous substance such as paper or fabric. A printing press that simultaneously prints both sides of a sheet of paper as it passes through the press. On other presses, printing both sides means running the sheet through the press to print one side, allowing the ink to dry, turning the paper over, and then running the sheet through the press again to print the other side. A paper that can resist large chemical and physical changes over and extended time (several hundred years). This paper is generally acid-free with alkaline reserve and a reasonably high initial strength. The degree to which paper resists deterioration over time. There is an international norm which applies to woodfree papers. The ISO 9706 international norm defines the conditions for producing "permanent" papers. A paper which fulfils these criteria can be stocked for many years under archival conditions (temperate medium and protected from light). Furthermore there is also the German DIN 6738 norm which can be applied to all papers. Under the DIN 6738 norm, longevity is classified under the following categories : CL 24-85 : these papers can be described as agei ng-resistant, CL 12-80 : the lifespan of these papers is of several centuries, CL 6-70 : the lifespan of these papers is of at least 100 years, CL 6-40 : the lifespan of these papers is of at least 50 years. However in the German introduction to the ISO 9706 norm, there is a clear restriction concerning the DIN 6738 norm : "The task of archives, libraries, museums and other collections is to conserve documents on a long lasting basis". That is why printers and editors should take care to respect the requirements of the ISO 9706 norm. DIN 6738 is valid for books which will predictably be destroyed after use. Chemical test performed on pulp to determine the degree of delignification. Degree to which a fluid (gas or liquid) permeates or penetrate a porous substance such as paper or fabric. Any material present in waste paper that is difficult to see or detect and which might be detrimental to the paper being manufactured from the wastepaper or which might either damage paper making equipment or Page 65 of 88
Peroxide Bleaching or Hydrogen Peroxide Bleaching pH (Hydrogen Ion Concentration) Photodegradable
Photographic Paper
Pick Out
Pick Resistance Pick Up Roll Picking (Papermaking) Picking (Printing)
Pigment
Pigmentizing Pin Holes
Piping
Pitch Ply
Point Polymer
render repulping difficult Method of bleaching pulp with hydrogen peroxide (H2O2) to remove lignin; reduces or avoids the need for chlorine dioxide in final bleaching. A measure of the acidity (or alkalinity) of a solution. Range from 0-14 with 7 being neutral, less than 7 being acid; higher than 7 being alkaline. A material which undergoes destruction of its chemical structure when exposed to light. Typically, the materials become brittle with time and fragment into small pieces or powder. The base paper used for the production of photographic papers is a dimensionally stable, chemically neutral chemical pulp paper with wet strength properties, that must be free from contaminants. Today papers are coated on both sides with a thin polyethylene film. The cooking prevents chemicals and water entering the paper during development. This also permits shorter rinsing and drying cycles. A problem on press caused by unevenly sealed paper, or paper with low bonding strength. The ink "picks" off weak areas of the paper, lifting coating from a coated stock or lifting fibers from an uncoated stock, and transferring them to the printing blanket. These fibers will eventually be transferred back onto the sheets being printed, causing inking and surface inconsistencies. The ability of paper fibers to hold together during the printing process. Roll, which lifts the wet paper or paperboard off the wire to transfer to press. To transfer the wet sheet from wire part to press part. If the sheet moves unsupported is called "poor man pick up". If a solid/suction roll is used to lick/pick the sheet, it is referred as closed transfer. The problem of ink picking off paper fibers during printing. This may be an indication of a paper with low bonding strength or the use of an ink with too much tack for the paper it is printed on. An ingredient added to pulp to increase the brightness and opacity of white paper or dye the pulp to create a colored sheet. Pigments have very high lightfastness and bleedfastness. Coating of paper with a chemical agent (pigment) to reduce surface porosity and increase opacity. Imperfections in paper which appear as minute holes upon looking through the sheet. They originate from foreign particles, which are pressed through the sheet. Defect in reels, consisting of ridges running around the circumference, due to moisture take-up by the surface layers or uneven binding or hard and soft spots. Resinous material present in wood (mainly softwood) that carry over into the pulping and papermaking system to form insoluble deposits. The separate webs, which make up the sheet formed on a multi-cylinder machine. Each cylinder adds one web or ply, which is pressed to the other, the plies adhering firmly upon drying. A unit of paper or paperboard thickness measuring one-thousandth of an inch. A chemical term for several classes of organic or carbon containing chemicals where a monomer or single chemical molecule is connected to itself in repeating units to form a chemical "chain." An example of a Page 66 of 88
Porosity Postcard Board Post-Consumer Waste Paper Poster Paper Precision Sheeting Pre-Consumer Waste Paper Press
polymer is cellulose, a repeating chain of glucose (sugar). Other examples are polyesters, nylons, viscose, lyocell, polyolefins and polystyrenes. The property of paper that allows the permeation of air, an important factor in ink penetration. Postcard board is either slightly mechanical or woodfree and calendered. Waste paper materials recovered after being used by consumers. Poster paper is a highly mechanical, highly filled, mostly coloured paper that has been made weather resistant by sizing. Converting rolls of paper into finished sheet sizes in a single operation. Paper recovered after the papermaking process, but before used by a consumer. A combination of two or more rolls used to press out water from wet paper web. Following are some of the types of the press.
Press Part or Press Section Pressure Sensitive Coated Paper
Pressurized Groundwood Pulp (PGW)
1. Plain Press or Solid Press This is the simplest and the oldest type of press which is now a days rarely used except on very slow speed machine. The solid press consist of two solid rolls covered with rubber and or granite. The top roll is somewhat offset for the squeezed out water to flow b y gravity. 2. Suction Press In this type of press, one roll is drilled and shell of the drilled roll rotates over a suction box. The squeezed water is sucked out through the felt. 3. Grooved Press In this type of press, one roll is grooved. The squeezed water is hold in the groves and removed by doctoring or sucking out on the return run of the roll. 4. Smoothing Press A plain roll press just before the dryer section start, used to smoothen the paper surface. The section of the paper machine which contains press (es). It is usually located between wire part and dryer part. Paper coated with a self-adhesive material which in dry form (solvent free) is permanently tacky at room temperature. A bond with the receiving surface may be formed by the application of pressure (e.g. by the finger or hand). A permanent adhesive is characterized by relatively high ultimate adhesion and a removable adhesive by low ultimate adhesion. Until the time of application, the adhesive surface should be covered by a suitable release coated paper. Mechanical pulp produced by treating logs with steam before defibration against a grindstone under externally applied pressure.
Page 67 of 88
Pulp
The overall performance of the paper on press. The transfer of ink onto paper or other materials to reproduce words and images. A suspension of cellulose fibers in water.
Pulp Board
Also known as Printers’ Board, this grade is made from a single web of pulp
Printability Printing
Pulper Pulping
Puncture Resistance
Rag
on a paper making machine, and is produced in various substances. Used for index cards and other general products, these boards may be white or colored. Unit for defibrating (slushing) pulps and paper machine broke, usually at the wet end of the paper machine. Pulping is the process by which plant material (wood, grass, straw etc.) is reduced to a fibrous mass. It is achieved by rupturing bonds within plant structure. It can be accomplished mechanically, thermally, chemically or some combinations of these treatments. The puncture resistance of combined board indicates the ability of the finished container to withstand external and internal point pressure forces and to protect the product during rough handling. The term “rag” is often used interchangeably with “cotton fiber content”
and harkens to a period of time when paper was actually made using cotton rags which were cleaned and then broken down into fibers which were then used to manufacture paper. In a sense it could be stated that the fine paper business has been engaged in recycling materials for production since its very beginning. Today paper is no longer made from rags and the term “rag” is falling in disfavor by the industry in lieu of the phrase “cotton fiber content”.
Page 68 of 88
Rag Paper
Rag Pulp Ragger Rope
Rattle Ream Recovered Paper
Today rag paper is mostly made from vegetable fibers consisting of cellulose, such as cotton, linen, hemp and ramie. Rags are the most precious raw material for the papermaker. Rag papers and rag-containing papers with admixtures of chemical pulp are used for banknotes, deeds, documents, books of account, maps and copperplate engravings and as elegant writing papers. They are also used for special technical applications. Papermaking pulp made from textile waste, cotton, hemp or flax. A rope used to remove contraries from the pulper.
That combination of properties such as stiffness, density etc. which is responsible for noise when the sheet is shaken or flexed. 500 Sheets of paper. Paper recovered for recycling into new paper products. Recovered paper can be collected from industrial sources (scraps, transport packaging, unsold newspapers...) or from household collections (old newspapers and magazines, household packaging). Page 69 of 88
Recovered Paper Grades Recovery Boiler
Recovery Rate (Paper) Recovery Rate (Chemical) Rectifier Roll or Holey Roll Recycled Fiber Recycled Fiber Pulp Recycling Reed
Recovered paper sorted by types in order to be recycled by paper mills. Specific grades are used by paper mills, in order to produce different types of paper and boards. Boiler used to burn black liquor from chemical pulping for recovery of inorganic chemicals as well as for energy production.
Amount of paper recovered as a percentage of amount o f paper consumed. Amount of chemical recovered in chemical recovery process as a percentage of chemical used in pulping. Chemical loss is compensated my make up chemicals. Hollow perforated roll in headbox used for even out the flow of fibers and prevent settling of fibers in headbox by providing gentle agitation. Fiber obtained from recovered paper; also secondary fiber (cf. virgin fiber). Pulp produced from recovered paper to be used i n papermaking. Use of recovered waste paper and board by paper mills to produce paper and boards. General name of various perennial plants; e.g. common reed, reed canary grass, giant reed; potential feedstock for pulping and papermaking.
Page 70 of 88
Reel
A continuous sheet of paper wound on a core.
Refiner
An equipment used to give mechanical treatment to the fibers.
Refiner Mechanical Pulp (RMP) Refiner Sawdust Pulp Refining Reflectivity Refractiveness
Mechanical pulp produced by passing wood chips between the plates of a refiner. Mechanical pulp produced from sawmill dust.
Registration Reinforcement Reinforcement Pulp Reject
[see Beating] Ability of paper or board to reflect light; a measure of gloss. A measure of how much a sheet of paper deflects the light that hits it. The more light a sheet deflects, the greater its refractiveness, allowing a printed image to be more brilliant and detailed. Putting two or more images together so that they are exactly aligned and the resulting image is sharp. Method for strengthening paper with an insert or surface layer of glass or other synthetic fiber or metal . Softwood chemical pulp added to give paper greater strength and to improve runnability on the paper machine or printing press. Material removed and discarded during the cleaning and screening of pulp/stock. Page 71 of 88
Release Paper
Release paper is used to prevent the sticking of glue, paste or other adhesive substances. Coating paper with silicone yields papers with a surface that prevents adhesion of most substances. Application: cover material for self-adhesive papers or films, e.g. in label production.
Relief
A method for printing ink on paper, using type or images that rise above the surface of the printing plate. Ink sits on top of these raised surfaces, and as the paper is pressed onto them it picks up ink. Letterpress, flexography, and rubber stamps all use relief plates. In letterpress, intense pressure can cause images to be slightly debossed or depressed below the surface of the paper. Fibers derived from sawmills scraps, plywood plants and other timber management activities. A paper's ability to return to its original form after being stretched, bent or compressed during the printing and bindery process. The amount of filler or other material which remain in the finished paper expressed as a percentage that added to the furnish before sheet formation. Retention can occur by various mechanisms. The simplest of these is mechanical sieving by the forming fabric. Once a fiber mat begins to form, the mat itself usually can act as a much more effective and finer sieve than the forming fabric. But even then, particles less than about 10 micrometers in size are not effectively retained by sieving. Rather, retention of fine particles requires the action of colloidal forces, including polymeric bridging or a charged patch mechanism. Retention aid chemicals can be effective either by attaching fine particles to fiber fines or fibers or by agglomerating them so that they can be sieved more effectively. Chemical additives, especially high molecular weight copolymers of acrylamide, designed to increase the retention efficiency of fine materials during paper formation. Equipment which slits and rewinds paper webs into small er rolls.
Residual Fibers Resilience Retention
Retention Aid
Rewinder
Page 72 of 88
Rice Paper
Ridges Ring Crush Test (RCT) Rising Film Evaporator
Rod Coater
Roe Number Roll Coating Roofing Paper Rosin
Rosin Size Rotogravure
Rough Rough Finish Runnability
Sack Safety Paper
Salt Cake Sanitary Papers
A common misnomer applied to lightweight Oriental papers. Rice alone cannot produce a sheet of paper. Rice or wheat straw is used occasionally mixed with other fibers in paper making. The name may be derived from the rice size (starch) once used in Japanese papermaking Roll defect where there are raised bands or rings of material around the circumference of the roll. A test method for measuring the edgewise crush resistance by forming the paper into a cylinder and applying a crushing force to the edge. (TAPPI T818) A type of tubular heat exchanger used for concentrating a solution consisting of a non-volatile solute and a volatile solvent; solution flows upward on the heat exchange surface; vaporization ' of the volatile solvent reduces the density of the mixture and causes the vapour-liquid mixture to rise; commonly used in pulp mills but less common in new installations. In rod coater, the rod is the metering device, which controls how much wet coating is allowed to leave the coating station. Typically thirty times more will be applied compared to the actual target coat weight. Measure of the amount of chlorine required for bleaching pulp. A process in which the coating is applied by roll and subsequently smoothed by means of reverse rolls contacting the freshly coated surface. Board that is impregnated with tar, bitumen and/or natural asphalt. Rosin, a natural resin from pine trees in combination with alum, is used for internal sizing of paper in acidic paper making. The chemical formula of rosin is C19H29COOH. Partially or completely saponified (neutralized) rosin. The chemical formula of rosin is C19H29CONa. The opposite of letterpress printing in that the design areas are recessed into the plate instead of being a relief. It is web-fed and prints thin, quick drying ink to produce multiple colors. Used in corrugated packaging. Heavily textured surfaces produced by minimal pressing after sheet formation. Paper having an exceptionally rough or coarse textured surface. The ease with which a paper moves through a printing press or converting machine. This is primarily determined by the paper's strength, tear resistance, dimensional stability, bonding strength and water resistance The term is used interchangeably with the word "bag" applied to a nonrigid container made from paper or other flexible material. Papers with a special protection against abusive imitation. The safeguards used during the production of the paper - some of them chemicals are secret. Or sodium sulfate added to the black liquor to compensate for the soda loss. The group of sanitary papers includes cellulose wadding, tissue and crepe paper, made from waste paper and/or chemical pulp - also with admixtures of mechanical pulp. As a consequence of the importance of tissue today, this name is now used internationally as a collective term for sanitary papers. These grades are used to make toilet paper and numerous other sanitary products such as handkerchiefs, kitchen wipes, towels and cosmetic tissues.
Page 73 of 88
Sanitary Tissue Paper
Sap Wood
Tissue is a sanitary paper made from chemical or waste paper pulp, sometimes with the admixture of mechanical pulp. It has a closed structure and is only slightly creped. It is so thin that it is hardly used in a single layer. Depending on the requirements the number of layers is multiplied. Creping is made at a dryness content of more than 90 %. The dry creping (unlike with sanitary crepe papers) and the low grammage of a single tissue layer result in a high softness of the tissue products. For consumer products it is normally combined in two or more layers. The flexible and highly absorbent product [is mainly produced from chemical pulp and/or DIP - sometimes also with admixture of groundwood pulp] can also be provided with wet strength. Applications: facial tissues, paper handkerchiefs, napkins, kitchen rolls, paper towels, toilet paper. The fluid part of the tree that moves up from the roots through the outer portion of the trunk and branches and contributes to its growth.
Satin Finish Save-All Saw Dust
A smooth, satin-like, semi-glossy finish of paper or Bristol. Equipment used to reclaim fibers from white water. Fine wood particles created when sawing wood; used as biofuel, pulping raw material, panel board production, animal litter etc.
Scaling
To impress or indent a mark with a string or rule in the paper to make folding easier. To impress or indent a mark with a string or rule in the paper to make folding easier. An internal bond test that measures the force needed to separate fibers within a single ply by TAPPI method.
Score Scott Bond
Page 74 of 88
Screen
Scuff Resistance Seam Secondary Fibers Security paper Self Adhesive paper
Semi-Alkaline Pulp (SAP) Semi-Bleached Pulp Semi-chemical Pulp Sett Shade
Shadow Mark
Shake Sheffield Porosity
Sheeter or Cutter Shives
Device used to remove large solids particles such as fiber bundles and flakes from stock. In good old days screen used to be open type and could deal with thin stock only. Modern screen are closed (pressurized) and can handle low, medium and even high consistency stock. Perforation in screen basket can be circular, counter shrink or slotted. The screen used just before headbox not only remove large particles but also align fibers in the direction of stock flow. Linerboard's ability to resist abrasion in the shipping environment may affect external appearance. The means of joining the two ends of the fabric together. Fibers recovered from waste paper and utilized in making paper or paperboard. Paper which includes identification features such as metallic strips and watermarks to assist in detecting fraud and to prevent counterfeiting. Used essentially for labeling purposes, this grade has a self-adhesive coating on one side and a surface suitable for printing on the other. The adhesive is protected by a laminate which enables the sheet to be fed through printers or printing machines, the laminate subsequently being stripped when the label is applied Sulfite pulp cooked at slightly alkaline pH (normal sulfite pulp is cooked at acid pH). SAP is superior in strength to normal sulfite pulp. Used mainly in printing papers. Pulp bleached to a brightness somewhere between that of unbleached and fully bleached pulp. Pulp produced by chemical treatment followed by mechanical treatment. A number of units or bales picked up at the same time by crane or truck. The color depth and hue in comparison to papers that are the same color; also used to describe the color achieved by adding dye to pulp slurry. There is a wide shade variety in white papers, as well as in colored papers. A defect in paper appearance which looks like the drilling pattern in a suction roll. It is due to opacity effects caused by areas of vacuum and pressure as the wet web passes over a suction roll . The device to shake the wire at the breast roll end from side to side. A test used to measure the smoothness of paper by measuring the rate of air flow over the surface of the sheet. The lower the number, the smoother the sheet. Machine for cutting the paper web into sheets. Small bundles of fibers that have not been separated completely during pulping.
Page 75 of 88
Show Through
Showers
The degree to which a printed film is visible through paper due to the low opacity of the paper. The undesirable condition in which the printing on the reverse side of a sheet can be seen through the sheet under normal lighting conditions. The more opaque a sheet, the less the show-through. Water jets or sprays used throughout the pulp and paper mills to wash wire mesh screen, forming wires, press felts, pulp mat, to dilute pulp etc. High Pressure Showers, a shower consisting of numerous needle jet nozzles along its length at a pressure of up to 300 psi. Lubrication Showers , a shower consisting of fan nozzles along its length to provide full coverage of the felts surface with water. This lubricates the felt as it passes over the suction boxes.
Side Run
Size Press
Sized Paper
Sizing Slice Slide Resistance
Slimes Slime Holes
Slitter Slitting
Oscillation Showers, the movement from side to side of the shower bar to ensure full coverage of the felts surface by the water jets. 1. A narrow reel removed from a web during processing, the width of which is less than the size ordered, but is large enough to permit its use for purposes other than re-pulping. 2. An additional part of an order placed in order to better utilize the maximum trimmed machine width of the making machine.
Section of paper machine where surface treatments are applied to the sheet of paper to give it special qualities. Normally comprised of a pair of rolls towards the end of the dryer train between which the dry or partially dry web is passed, and into the nip of which a liquid, usually starch, is applied to impart strength to the sheet. Sometimes a chemical may be added to produce a water-resistant sheet. Sizing reduces the water absorbency of the paper and thus creates the condition for the writability with ink. Sized paper is also used for many other purposes (printing, coating, gluing, etc.), and the sizing agents must fulfill a wide range of tasks. For instance, they control the water absorbency and increase the ability to retain water and ink (pick resistance). The treatment of paper which gives it resistance to the penetration of liquids (particularly water) or vapors. Sizing improves ink holdout. Outlet from the head box through which the pulp suspension is fed into the forming section. The ability of containers to resist sliding in unit loads can be predicted for the coefficient of friction of the combined board. A low coefficient demonstrates containers slipping from the load. Fungus or other bacteriological growth. If not controlled in papermaking system, may cause process and quality problems. A hole in paper, characterized by brownish translucent material around the edges. Caused by a lump of slime which has formed in stock system from the growth microorganisms, then becoming detached and flowing onto the paper machine wire with the fiber to form a non-fibrous area. Rotary knife used to slit or trim a paper web into specified width. Dividing a web of paper in the lengthwise direction into two or more narrower webs. Page 76 of 88
Slowness Sludge
Smelt Smooth Finish Smoothness Soda Pulping Soft Cook Soft Nip Calendar
Softwood
Solid Fiberboard Specialty Paper
Specialty Pulp Specific Energy (Refining) Specific Surface (Fiber) Specific Surface Load (Refining) Speck Spent Liquor Splice Spread Coating
Stampers Standard Test Conditions Starch
Measure of pulp drainage. Has an inverse relationship to freeness. The waste material left over after pulping and deinking. Although some sludge is produced in the virgin papermaking process, far more is produced in the deinking (recycling) process. Recycling breaks recovered paper down into fibers, which are sent to the paper machine for new production, and other materials, which drop into the sludge. These "other materials" include clay coatings, fillers from the previous paper, paper clips and staples, fibers too short to be made into paper, ink if it wasn't skimmed off in the deinking process, and any "junk" that crept into the wastepaper bales. Inorganic chemicals obtained in molten form from the recovery furnace. A highly calendered or machine-finished sheet. The surface uniformity of paper. Sheets that are flat and even provide better ink dot formation and sharper images. An alkaline pulping process that uses a simple, sulfur- free sodium hydroxide as cooking liquor. Over-cooked pulp. A machine device consisting of two or more pairs of steel and composition rolls; it is designed to achieve much of the quality of a Supercalender, with much of the production advantage of being on machine, but without the severe operating difficulties of an on-machine Supercalender. Woods obtained from coniferous trees. Generally grown in cold climates. Softwood grows slower than hardwood but have longer fibers compared to hardwood. Collective term for all solid board grades. The group of specialty papers comprises numerous paper grades, each characterized by particular properties. These properties often require special raw materials. Chemical pulps used for purposes other than ordinary papermaking (e.g. in textile production) Energy applied per unit weight on oven dry basis (KWH/MT) during refining. Fiber surface area per unit weight (OD basis) Specific edge load divided by refiner bar width factor (Watt-Sec/m2) A small defect of foreign substance with contrasting appearance to the surrounding paper. Liquor recovered from cooked pulp. Formed by overlapping webs and joining with a strip of double-faced adhesive tape. Used for lighter-weight grades of paper. A method of coating a web of paper by means of a vertical plate restraining a pond of viscous coating material, for example resins, plastics or adhesives, which is drawn through an adjustable gap between the plate and the paper by the forward movement of the web over a horizontal support The wooden hammers used in a watermill to pulp rags in order to separate the fibers. Atmospheric conditions of temperature and humidity in which laboratories agree to conduct tests, eliminating those variables in comparing results. A natural product from corn, potatoes, tapioca, etc., and used for dry strength. Cationic starch is added at the paper m achine wet end. Page 77 of 88
Starch is a free flowing white powder. Typically, starch used in the paper industry is extracted from maize kernels, wheat or potatoes; in rare cases, tapioca or rice can be the source. Starches from the different plants each have a characteristic granule size and shape. Potato starch is often referred to as farina, and maize starch is sometimes called corn. Native starch is sometimes called pearl starch.
Steam Finishing or Steam Calendering Steaming
Stencil
Stickies Stiffness
Stock
Stock Preparation Straw Pulp Strawboard Stretch Strike-through
A way of treating paper before calendering to improve its density and surface smoothness Wood chips are often treated with steam prior to pulping; used in thermomechanical pulping. Also injection of steam in direct or indirect cooking digester for chip packing and or cooking. A sheet of plastic, paper, or other material with letters or an image cut out of it. When placed on a surface and inked, it reproduces the cut-away images onto the material behind it. Sticky materials in recycled papermaking pulp, often resulting from pressure-sensitive labels. The ability of paper or paperboard to resist an applied bending force and to support its own weight while being handled. A sheet that is too limp can cause feeding and transport problems in copiers and printers. An adequate degree of stiffness is important to avoid distortion of the paper due to the pull of ink during offset printing. Stiffness is critical to many converting operations for forms and envelope grades. A term used to define pulp after mechanical (refining or beating) and /or chemical treatment (sizing, loading, dying etc.) in the paper making process. A pulp ready to make paper. Collective term for all treatment necessary for the preparation of the stock before it reaches the paper machine. Pulp that is made from the straw of grains such as rice straw. It is cooked by soda process. Board made from partially cooked straw, bagasse or grass or a mixture of these. The maximum tensile strain developed in paper before rupture. The stretch or percentage elongation is expressed as a percentage. The penetration of ink through paper. Page 78 of 88
Substrate Suction Box (Vacuum Box)
Sulfate Pulping Sulfite Pulping Supercalender Supercalendering Surface-Sized
Surface Roughness
Surface Smoothness
Surface Strength Test Swelling Synthetic Fiber Paper
T4S
The base material on which a substance (such as ink, adhesive, coating) is applied. Device that removes water from the paper machine by a suction action located beneath the wire at the wet end.
Alkaline process of cooking pulp. Acid process of cooking pulp A stack of alternating steel and fiber-covered rolls at the end of the paper machine which is used to increase a sheet's gloss and smoothness. Treatment of paper on an off-machine supercalender to improve smoothness and gloss. Paper that has been treated with starch or other sizing material at the size press of the paper machine. This term is used interchangeably with the term "tub-sized", although tub-size more properly refers to surface sizing applied as a separate operation where the paper is immersed in a tub of sizing (starch or glue), after which it passes between squeeze rolls and is air dried. For coated boards, Parker Print Surf (PPS) roughness tester is used where the test result is expressed as an average of the surface profiles in micrometers (mm) low results show smooth surface while high results indicate poor surface. For coated board, Bendtsen method readings given as total leakage of air in ml/min. Smoother surface has lower readings The smoothness of the linerboard surface may affect printing quality because slight depressions may not receive complete ink coverage. Surface smoothness may also affect the coefficient of friction, gloss and coating absorption. The method consists of printing a strip of paper in a print tester at an accelerating rate. The method is preferable to Wax P ick. An increase in volume of fiber due to the absorption of liquid. Papers made from synthetic fibers such as polyamide and polyester, from viscose staple fiber or sometimes also with fillers. The fibers are mainly held together by binders. The durable synthetic fiber papers are used for maps and highly important documents such as driving licenses or vehicle registration books. Abbreviation indicating that the paper has been guillotine trimmed on all four sides. Literal translation: trimmed four sides. Page 79 of 88
Table Roll
The small diameter rolls used to support the wire.
Tack or Stickiness
Tack is a critical property of the ink used in lithography. Because the ink sits on a flat surface, it needs internal cohesion; in other words, it needs to stick to itself so that it doesn't run all over the plate. However, too much tack can cause it to pull the paper apart.
Tag Paper
Talc Tear Index Tear Resistance Tear Strength Tensile Energy Absorption (TEA) Tensile Index Tensile Strength Testliner
Text Paper
Thermal Paper Thermal Transfer Printing Thermo Mechanical Pulping (TMP)
When printing two or more ink colors in line, the ink tack and sequence must be adjusted in order for the inks to adhere to each other as well as to the paper. A heavy utility grade of paper used to print tags, such as the store tags on clothing. Tag paper must be strong and durable, yet have good affinity for printing inks. Mineral used in papermaking as a filler and coating pigment. Tear index = tearing resistance/basis weight. The mean force required to continue the tearing of paper from an initial cut under standardized conditions. A measure of how likely a paper will continue to tear once started. Tear strength will differ with and against the grain. It is the work done when a paper specimen is stressed to rupture in tension under prescribed conditions as measured by the integral of tensile strength over the range of tensile strain from 0 to maximum. 2 Tensile index = tensile strength (N/m) /basis weight (g/m ). A measure of how likely a paper is to break when pulled at opposite ends. This is very important when running through high-speed web presses. Mainly produced from waste paper used as even facing for corrugated board or as liner of solid board. They are often produced as duplex (twolayer) paper. The grammage is higher than 125 gsm. Text papers are defined as fine, high quality uncoated papers. Typically, they are made in various colors, with numerous textures and a variety of surface finishes. Text papers are made from high-grade bleached wood pulp, cotton fibers, or tree-free pulp such as bamboo. Recycled sheets include high quality recycled waste paper and post-consumer waste pulp, i n addition to bleached wood pulp, tree-free pulp or cotton fibers. Any paper with a heat-sensitive coating on which an image can be produced by the application of heat. Printing whereby a design image is first printed on heat transfer paper using inks with sublimable dispersed dyes. Mechanical pulp made by steaming wood chips under pressure prior to and during refining, producing a higher yield and stronger pulp than regular stone groundwood or regular refiner wood pulp. Page 80 of 88
Thin Paper Thinning
Tint Tissue
Includes carbonizing, cigarette, bible, air mai l and similar papers. A practice in which certain trees are removed from a dense stand to allow the remaining trees adequate sunlight, nutrients and moisture to grow at an even rate. To vary a color by adding white. Also, a very light or delicate variation of a color. A low weights and thin sheet. Normally a paper sheet weighing less than 40 gram per meter square is called tissue. At-Home products: Also known as Consumer Products, these are the tissue products you purchase in the grocery store and convenience store for use in your home and include toilet paper and facial tissue, napkins and paper towels, and other special sanitary papers. Away-from-Home products: Also known as Commercial & Industrial Tissue, these are the products that serve markets such as hospitals, restaurants, businesses, institutions, and janitorial supply firms. Specialty: These types of tissue papers are often high-end, decorative papers that are glazed, unglazed, or creped, and include wrapping tissue for gifts and dry cleaning, as well as crepe paper for decorating.
Titanium Dioxide
Tolerance Ton on Tonne
Top Side Total Alkali Totally Chlorine Free (TCF) Translucency Translucent Drawing Paper
Transparency Transparent Paper
Facial tissue: The class of soft, absorbent papers in the sanitary tissue group. Originally used for removal of creams, oil, and so on, from the skin, it is now used in large volume for packaged facial tissue, toilet paper, paper napkins, professional towels, industrial wipes, and for hospital items. Most facial tissue is made of bleached sulfite or sulfate pulp, sometimes mixed with bleached and mechanical pulp, on a single-cylinder or Fourdrinier machine. Desirable characteristics are softness, strength, and freedom from lint. An opaque and expensive compound used as a white pigment and opacifier in papermaking. Elemental titanium is a lustrous, lightweight, white metal with exceptional strength. Permissible degree of variation from a pre-set standard. Metric ton or Metric Tonne is equal to 1000 Kgs. or 2240 lbs. English tons are as defined. Long Ton = 2240 lbs is similar to metric ton. Standard English ton is 2200 lbs. Short ton is 2000 lbs. Side of the paper opposite to the wire side. NaOH + Na2S + Na2CO3 + 0.5*Na2SO3 all expressed as Na2O in alkaline pulping liquor. Totally chlorine free applies to virgin fiber papers that are unbleached or processed with a sequence that includes no chlorine or chlorine derivatives. The ability to transmit light without being transparent. A paper suitable for drawing office use; sufficiently translucent for an image on it to be reproduced by processes using transmitted light and for a design to be traced on it from an original placed beneath it. Such processes include blueprint and diazo. Ability of paper to allow light rays to pass through so that objects behind it can be clearly seen. Extended and particularly careful grinding of high quality fibers (hard chemical pulps, rags) yields a raw material permitting the production of
Page 81 of 88
Treated Paper
Trim Tub Sizing Tube Digester Twin-wire Machine
Two Parallel Fold
Two-Sidedness
Union Kraft
Unglazed Paper Un-sized Paper Urban Forest Urban Wood
UV Coating
UV Ink
V Fold Vacuum Box Vacuum Pickup Vapor Phase Pulping Vaporproof Paper
Vat Machine
transparent paper. Papers which have functional characteristics added through special treatment. Among the most common are insect resistant, mold resistant, clay coated, and flame retardant. To cut true to exact size, by cutting away the edges of paper in the web or sheet. The operation of surface sizing paper by passing it through a bath of a suitable solution such as gelatin. Single or multi-tube continuous digester; used mainly in nonwood pulping and sawdust pulping purposes; horizontal tubes. A papermaking machine with two continuous forming wires, rather than just one. Twin-wires were designed to create a less two-sided paper than paper manufactured on a Fourdrinier paper machine. Other techniques for reducing two-sidedness have since been developed, enabling paper manufacturers to create paper on singl e-wire machines with little side-to-side variation. An excellent fold for legal size (or larger) pieces that are to be mailed. A legal sheet (8.5" x 14") is folded to 3.5" x 8.5". A 9" x 16" sheet produces a 4" x 9", four panel brochure. Note: A perforation added at one of the folds can create a three panel brochure with detachable reply card. The property denoting a difference in appearance and printability between its top (felt) and wire sides. A packaging material comprising two layers of Kraft paper bonded together by means of a laminate that is resistant to the transmission of water in liquid or vapor form. E.g. bitumen or plastic. Un-calendered paper. A paper which has not been sized. A description of towns and cities which are the source of wastepaper as one of the raw materials used for paper making. Used pallets, wooden shipping crates and clean construction wood diverted from the waste stream and chipped for use in making particleboard and medium density board. A very glossy, slick coating applied to the printed paper surface and dried on press with ultraviolet (UV) light. UV coating can cause slight variations in match colors, so consult an ink manufacturer or printer for best results. An ink specially formulated to dry quickly with ultraviolet light while still on press. Fast UV drying eliminates the need to wait for the first side to dry before printing the second side. V-fold has one fold which creates two panels. [see Suction Box] Transfer of paper from wire to press felt using a perforated vacuum roll. Cooking impregnated chips predominately in a vapor phase. Paper or paperboard that has been chemically treated or laminated with vapor barrier so that it will resist the passage of gases or vapor through it. It is typically used for food packaging. A paper or board making machine comprising one open ended cylinder, or more than one open ended cylinder in series, covered with fine mesh wire, Page 82 of 88
Vat Paper Vehicle Vegetable Parchment Veining Vellum Paper
which revolves in a vat of stock. Water draining through the wire leaves a mat of fibers on its surface and the ultimate thickness of the product may be determined by the number of cylinders used. The resultant web is removed from the last cylinder and then passed through conventional pressing and drying sections. Paper made, usually one sheet at a time by dipping special wire screen molds in vats of pulp stock and allowing water to drain away by gravity. The liquid part of the ink, giving it the flow properties that enable it to be applied to a surface. Paper that has acquired, by the action of sulfuric acid, a continuous texture. It offers high resistance to disintegration by water a nd grease. Uneven coloring of pulp. 1. Paper finish that exhibits a toothy surface similar to eggshell or antique and is relatively absorbent for fast ink penetration. 2. A high-grade paper made to resemble parchments originally made from calf’s skin.
Vented Nip Press
Verdol Paper Virgin Fiber Virgin forest Viscose Pulp Viscosity (ink) Vulcanizing
Wadding
Wall Paper Warp Washing Wash Press Washi Washing Deinking Water-Color Paper Waste Paper
3. Social and personal stationery is often called vel lum. A radial groove bottom press roll whose purpose is to reduce the fluid pressure gradient within the nip of the press by providing an area to escape for the water pressed out of paper and felt. Blind drilled roll also used for same purpose. A high strength rigid paperboard or pressboard made typically from jute fibers. It is also known as jacquard board. Fiber that has never been used before in the manufacture of paper or other products. Forest in its natural state, untouched by man. Dissolving pulp intended for the manufacture of viscose. A measurement of the fluidity of ink. A higher viscosity is the thicker, and the lower viscosity is thinner. A process to convert paper and paperboard in to a dense, hard, high strength paper by treating it with Zinc Chloride (ZnCl2) and Sulfuric Acid (H2SO4) which gelatinizes the surface cellulose. Single or multi-ply, loosely matted fiber sheet made from chemical pulp. Used in packaging, thermal and acoustical applications and as a cushioning medium. A paper used for wall covering. Also known as hanging paper. The machine direction yarns in a woven fabric (press felt, dryer screen etc.) A process of separating spent cooking or bleaching chemicals from pulp fibers. One type of pulp washer; uses pressing action for dewatering and displacement. Japanese handmade paper. Deinking in which solid particles are separated on the basis of their size by washing. A medium weight, hard sized, coarse surface paper, suitable for painting with water based colors. All kind of used paper or paper discarded or not considered fit for a particular use.
Page 83 of 88
Water Finished Paper Water Resistant Paper Water Retention Value (WRV) Water Vapor Transmission Waterleaf Watermark
Waviness
Wavy Edges
Wax Pick
Waxed Paper
Waxing Web Web Break Weft Wet Break Wet End Wet End Chemical Additives Wet Lap Machine
Wet Strength Paper Wet Tensile Strength Wetting Agent
A high glazed paper produced by moistening the sheet with water or steam during calendering. Paper which has been impregnated, coated or laminated to resist the penetration of water. The water retention value test provides an indication of fibers' ability to take up water and swell. The WRV is also highly correlated to the bonding ability of kraft fibers. The rate of water vapor transmission through containerboard indicates the ability of the finished container to protect its contents from undesirable effects of high humidly or moisture loss of the product. A paper with little or no sizing, like blotter, making it very absorbent If dampening is desired, this paper can be sprayed with a n atomizer. The image impressed into the formation of paper by the dandy roll on the wet end of the paper machine; can be seen by holding the watermarked sheet up to the light. Can be either a wire mark or a shaded image. A form of paper curl resulting when the sheet edges in the pile absorb moisture that the center of the pile cannot absorb; or the sheet edges surrendering moisture while the center remains moist. Warping effect in paper that is the result of the edges of the sheet having picked up moisture and expanded. Will normally happen only in a pile that prevents the center of the sheets from picking up the same amount of moisture and leveling out or cockling. It is usually a warm weather problem caused by improper balance between moisture content of the paper or too high humidity in the air. A process that measures the ability of inks to pick fibers or particles from the surface of paper as a manner of testing the surface strength of paper stocks. Nearly woodfree papers that are impregnated with paraffin, wax or wax/paraffin/plastic mixtures. With the appropriate saturation agent and process the product may be tailored for specific applications, e.g. packaging of bread or sweets or wrapping razor blades. Coating or impregnating of paper or board with paraffin or wax. Term used for the full width of the paper sheet in the process of being formed, pressed, dried, finished and/or converted. A tear in a web during the printing process. The cross machine direction yarns in a woven fabric (press felt, dryer screen etc.). A paper break at the wet end (on wire or press) during papermaking process. First part of the paper machine consisting of wire part and press part. Chemical additives added with the stock at the wet en d. Paper machine consisting essentially of a wire covered cylinder rotating in a vat of pulp stock on which a mat of varying thickness is formed by drainage. These mats are removed either intermittently in thick sheets called laps, or continuously. A chemically treated paper strong enough to withstand tear, rupture or falling apart when saturated with water. The measure of the force necessary to break a one inch strip if paper after it has been immersed in water. Substance that increases the wettability of a surface for a liquid. Page 84 of 88
White Liquor White Pitch White Top Liner White Water White Water System
Whiteness
Whole Tree Chip
Wicking Winder, Rewinder
Winding
White liquor is the aqueous solution of sodium hydroxide & sodium sulfide used as the cooking liquor in Kraft pulping. Deposits on papermaking equipment, a major component of which is latex binder from coated paper or broke. A two-ply sheet comprised of one bleached and one u nbleached layer. The filtrate from the wet end of the paper machine. Flow circuit for paper machine white water (includes pipes, storage tanks, cleaning equipment, water from forming section and return feed).
Whiteness of pulp and paper is generally indicated by its brightness, which is the reflectance of a wavelength of blue light. So-called white papers have a definite hue. Most are made with a blue white tint. Wood chips produced by chipping whole trees, usually in the forest. Thus the chips contain both bark and wood. They are frequently produced from the low-quality trees or from tops, limbs, and other logging residues. The bleeding of ink from the ink jet printing process into unwanted areas of the paper, causing a blurring effect of the printed character or image. Machine for cutting the paper web longitudinally into narrower webs, which are then wound to reels; also slitter-winder.
Operation whereby a web of paper or board is wound into one or more reels. Page 85 of 88
Wire or Machine Wire
The moving "screen" at the wet end of a paper machine where the sheet is formed.
Wire Guide Roll
The small diameter roll used for guiding (keeping on track) the wire. One end of the roll is adjusted to compensate any misalignment. The small diameter rolls used at the return run (Couch roll to Breast roll) of the wire. On the bottom or wire side of the paper, these are impressed traces of the machine wire. The side of a sheet next to the wire in manufacturing; opposite from the felt or top side; usually not as smooth as the felt or topside. The small diameter rolls used at the return run (Couch roll to Breast roll) of the wire to adjust the tension of the wire. Pulp furnish without mechanical pulp. Paper made without mechanical wood pulp. Mechanical or chemical pulp made from wood (cf. Non-wood pulp). The Paper having a uniform surface and no discernible marks. Soft, smooth finish, most widely used writing, printing, book and envelope paper. Relatively low opacity, brightness and bulk. The materials, consisting usually of paper or paperboard, sometimes with treatment for moisture barrier properties, which are used to protect the roll or pile form damage. Blade Wrinkle: Blade coating defect, an irregular line on the coated surface, essentially in the machine direction.
Wire Return Roll (s) Wire Mark Wire Side Wire Tension Roll Wood-Free Wood Free Paper Wood Pulp Wove
Wrapper
Wrinkle
Writing Paper
Xerography
Winder Wrinkle: Ridges at an angle to the machine direction, caused by hard sport in the reel. Uncoated paper that is suitable for writing with ink on both sides. The writing must neither bleed nor strike through. Writing paper is always fully sized and also suitable for printing. It can be woodfree or mechanical, depending on the intended purpose. The admixture of fillers makes it less translucent.
The printing process used by photocopying machines. Electric charge creates the image on an eloctro-photographic surface that works as a plate. This surface is cleared after each copy is made, and used over again for the next copy.
Page 86 of 88
Xylan
Xylanase
A type of hemi-cellulose in wood. Yellow, water-soluble, gummy polysaccharide found in plant (e.g. hardwood or cereal straws) cell walls; main structural components are xylose and other pentoses; yields xylose and other pentoses upon hydrolysis. Enzyme used for hydrolysis of xylan in pulp bleaching.
Yankee Machine
A type of Fourdrinier paper machine employing a single dryer of large circumference with highly polished surface.
Yellowing
Or brightness reversion is the discoloration of white paper primarily due to aging. Ratio of product output and raw material input, expressed in percentage.
Yield Z-Direction Z-Direction Tensile Strength Zero (Effluent) Discharge Z-Fold
The direction perpendicular to the plane of a sheet of paper. The tensile strength measured in Z-direction.
Zig Zag Folding
Folding used with continuous forms with alternating position (head and foot). Commonly used to convert roll paper to easily managed flat-back.
No effluent discharge from pulp & papermaking plant. A paper fold represented by back and forth fol ds into three panels.
Page 87 of 88
