PDS Sika AnchorFix S

Product Data Sheet Edition 5.20.2016 Identication no. C370 Sika ® AnchorFix-S

Sika ® AnchorFix-S High performance, two component adhesive anchoring system Description

Sika AnchorFix-S is specially formulated as a quick curing, two component, polyester-based adhesive anchoring system for installing steel threaded anchor rod or steel reinforcing bars into uncracked, solid concrete substrates.

Where to Use

n For

positive anchorage or doweling into uncracked, solid concrete substrates (e.g. concrete oors, concrete walls).

l a i t n e d i s e R

Advantages

n Cost

effective anchoring offering exceptional strength to use. n Fast curing. n Easy

Coverage

See below.

Packaging

10 .oz. cartridge.

Typical Data RESULTS MAY DIFFER BASED UPON STATISTICAL VARIATIONS DEPENDING UPON MI XING METHODS AND EQUIPMENT, TEMPERATURE, TEMPERA TURE, APPLICATION APPLICATION METHODS, TEST METHODS, ACTUAL SITE CONDITIONS AND CURING CONDITIONS.

Shelf Life

When stored correctly correctly,, the shelf life will be from 12 months from the date of manufacture.

Storage Conditions

Cartridges should be stored in their original packaging, the correct way up, in cool conditions (+41°F to +77°F) out of direct sunlight.

Mixed Density (ASTM D 1875)

0.06 lb / in3 (1.7 g / cm3)

Tensile Properties (ASTM D 638) Tensile Strength

24 hours 7 days

1,595 psi (11 MPa) 1,885 psi (13 MPa)

Elongation at Break

24 hours 7 days

0.09% 0.07%

Flexural Strength (ASTM D 790)

7 days

3,480 psi (24 MPa)

Compressive Properties (ASTM D 695) Compressive Strength

Compressive Modulus

4 hours 24 hours 7 days 7days

.

7,250 psi (50 MPa) 8,700 psi (60 MPa) 10,730psi (74 MPa)

4.5 x 105 psi (3,130 MPa)

PRIOR TO EACH USE OF ANY SIKA PRODUCT, THE USER MUST ALWAYS READ AND FOLLOW THE WARNINGS AND INSTRUCTIONS ON THE PRODUCT’S MOST CURRENT PRODUCT DATA SHEET, PRODUCT LABEL AND SAFETY DATA SHEET WHICH ARE AVAILABLE ONLINE AT HTTP://USA.SIKA.COM/ OR BY CALLING SIKA’S TECHNICAL SERVICE DEPARTMENT AT 800.933.7452 NOTHING CONTAINED IN ANY SIKA MATERIALS RELIEVES THE USER OF THE OBLIGATION TO READ AND FOLLOW THE WARNINGS AND INSTRUCTIONS FOR EACH SIKA PRODUCT AS SET FORTH IN THE CURRENT PRODUCT DATA SHEET, PRODUCT LABEL AND SAFETY DATA SHEET PRIOR TO PRODUCT USE.

C380

Cure Mechanism: Sikacryl PowerSet is a two component polyester formulation requiring a static mixing nozzle to combine the ingredients for a reactive chemical cure. Cartridge, Ambient an and Su Substrate Te Temperature

Gel Ti Time*

Cure Ti Time

41°F to 50°F (5°C to 10°C)

12 mins

120 mins

51°F to 68°F (11°C to 20°C)

6 mins

80 mins

69°F to 77°F (21°C to 25°C)

4 mins

40 mins

78°F to 86°F (26°C to 30°C)

3 mins

30 mins

87°F to 95°F (31°C to 35°C)

2 mins

20 mins

96°F to 104°F (36°C to 40°C)

90 secs

15 mins

* Gel Time is the typical amount of time for mixed Sika PowerSet to solidify at highest temperature in the range

Installation Specication

Property

Symbol

Unit

d

in (mm)

5/16 (8)

3/8 (10)

1/2 (12)

5/8 (16)

3/4 (20)

1 (24)

do

in (mm)

3/8 (10)

1/2 (12)

9/16 (14)

11/16 (18)

13/16 (22)

1-1/16 (28)

db

in (mm)

3/8 (10)

1/2 (12)

5/8 (16)

3/4 (20)

7/8 (22)

1-1/8 (28)

d

in (mm)

-

No. 3 (10)

No. 4 (12)

No. 5 (16)

No. 6 (20)

No. 8 (24)

do

in (mm)

-

1/2 (12)

9/16 (14)

11/16 (18)

13/16 (22)

1-1/16 (28)

db

in (mm)

-

1/2 (12)

5/8 (16)

3/4 (20)

7/8 (22)

1-1/8 (28)

Threaded Rod Diameter Drill Bit Diameter (preferred)


Drill Bit Diameter (maximum)

Rebar Size Drill Bit Diameter (preferred) Drill Bit Diameter (maximum) Cleaning Brush Size Min. Concrete Thickness

in (mm) h min

Min. Anchor Spacing s min

Min. Edge Distance c min

1/2 (14)

3/4 (20)

in (mm)

1-1/8 (29)

1.5 x Embedment Depth (i.e. 1.5 x h eff)

in (mm)

2 (50)

2 - 3/8 (60)

2 - 3/4 (70)

3 - 3/4 (95)

4 - 3/4 (120)

5 - 3/4 (145)

in (mm)

2 (50)

2 - 3/8 (60)

2 - 3/4 (70)

3 - 3/4 (95)

4 - 3/4 (120)

5 - 3/4 (145)

*The design professional on the job is ultimately responsible for the interpretation of the data provided above.

Coverage per Typical 10 . oz. (300 ml) Cartridge of Sika AnchorFix-S

Anchor size:

(in.)

5/16

3/8

1/2

5/ 8

3/4

1

Drill Hole Diameter:

(in.)

3/ 8

1/2

5/8

3/ 4

1

1 1/8

Embedment Depth:

(in.)

2 1/2

3 1/4

4

5

3 3/4

8

85

35

18

10

6

3

Esmated Number of Fixing *

Cartridge Volume

3 00

ml

*Number of xings assumes 30ml wastage in inial extrusion and holes lled to 3/4 f ull

Anchor size:

(in.)

5/16

3/8

1/2

5/8

3/4

1


(in.)

3/ 8

1/2

5/8

3/4

7/8

1 1/8

Embedment Depth:

(in.)

3 1/8

3 3/4

5

6

1

10

300 ml

68

27

14

8

7 1/2

2


Cartridge Volume


Anchor size:

(in.)

5/16

3/8

1/2

5/8

3/4

1


(in.)

3/ 8

1/2

5/8

3/4

7/8

1 1/8

Embedment Depth:

(in.)

3 3/4

4 1/2

6

7

1

12

300 ml

56

22

11

6

9

2


Cartridge Volume



Allowable Load Data in Tension and Shear for Sika AnchorFix-S (Traditional Allowable Strength Design Method) Anchor Diameter / Rebar

5/16”

3/8” No. 3


1/2” No. 4

5/8” No. 5

3/4” No. 6

1” No. 8

Allowable Concrete Capacity / Bond Strength

Drill Bit Diameter

3/8”

1/2”

9/16” 5/8”

11/16” 3/4”

13/16” 7/8”

1-1/16” 1-1/8”

Tension (lb)

Shear (lb)

f’c = 2,500 psi (17.2 N/mm2)

f’c = 4,000 psi (27.6 N/mm2)

f’c = 8,000 psi (55.2 N/mm2)

f’c = 2,500 psi (17.2 N/mm2)

f’c = 4,000 psi (27.6 N/mm2)

f’c = 8,000 psi (55.2 N/mm2)

1,070 (4.8)

1,120 (5.0)

1,200 (5.4)

1,425 (6.4)

1,495 (6.7)

1,605 (7.2)

1,340 (6.0)

1,400 (6.3)

1,505 (6.8)

1,785 (8.0)

1,870 (8.4)

2,005 (9.0)

1,605 (7.2)

1,680 (7.6)

1,805 (8.1)

2,140 (9.6)

2,245 (10.1)

2,405 (10.8)

1,435 (6.5)

1,505 (6.8)

1,610 (7.3)

1,915 (8.6)

2,005 (9.0)

2,150 (9.7)

1,795 (8.1)

1,880 (8.5)

2,015 (9.1)

2, 39 39 0 ( 10 10 .8 .8 )

2, 50 50 5 ( 11 11 .3 .3)

2,685 (12.1)

2,155 (9.7)

2 ,2 ,2 55 55 (1 0. 0. 2) 2)

2 ,4 ,4 20 20 (1 0. 0. 9) 9)

2,870 (1 (12.9)

3,010 (1 (13.5)

3,225 (1 (14.5)

2,715 (12.2)

2,845 (12.8)

3,050 (1 (13.7)

3,620 (1 (16.3)

3,795 (1 (17.1)

4,065 (1 (18.3)

3,395 (1 (15.3)

3,555 (1 (16.0)

3,810 (1 (17.2)

4,525 (20.6)

4,740 (21.3)

5,080 22.9)

4,075 (18.3)

4,265 (19.2)

4 ,5 ,5 75 75 ( 20 20 .6 .6 )

5 ,4 ,4 30 30 (2 4. 4. 4) 4)

5,690 (25.6)

6,100 (27.4)

3,870 (17.4)

4,055 (18.2)

4,345 (1 (19.6)

5,155 (2 (23.2)

5,405 (2 (24.3)

5,795 (2 (26.1)

4 ,6 ,6 40 40 ( 20 20. 9) 9)

4 ,8 ,86 5 ( 21 21 .9 .9 )

5 ,2 ,2 15 15 ( 23 23 .5 .5)

6 ,1 ,1 90 90 ( 27 27 .9 .9 )

6,485 (29.2)

6,950 (31.3)

5,415 (24.4)

5,675 (25.5)

6,085 (27.4)

7,220 (32.5)

7,570 (34.1)

8,110 (36.5)

4,610 (2 (20.7)

4,830 (2 (21.7)

5,175 (2 (23.3)

6,145 (2 (27.7)

6,440 (29.0)

6,905 (31.1)

5,760 (25.9)

6,040 (27.2)

6,470 (29.1)

7,680 (34.6)

8,050 (36.2)

8,630 (38.8)

6,915 (3 (31.1)

7,245 (3 (32.6)

7,765 (3 (34.9)

9,215 (41.5)

9,66 9, 660 0 (4 (43. 3.5) 5)

10,3 10 ,355 55 (4 (46. 6.6) 6)

7,490 (3 (33.7)

7,850 (3 (35.3)

8,415 (3 (37.9)

9,985 (44.9)

10,465 (47.1)

11,220 (50.5)

9,360 (42.1)

9,810 (44.2)

10,515 (47.3)

12,485 (56.2)

13,0 13 ,085 85 (5 (58. 8.9) 9)

14,0 14 ,020 20 (6 (63. 3.1) 1)

11, 1,23 235 5 (5 (50. 0.6) 6)

11, 1,77 775 5 (5 (53. 3.0) 0)

12,620 (56.8)

14 ,9 ,9 80 80 (6 (6 7. 7. 4) 4)

1 5, 5, 70 70 0 (7 (70 .7 .7 )

1 6, 6,8 25 25 ( 75 75. 7) 7)

. 1. The above values represent guideline Allowable Concrete Capacity / Bond Strength working loads based on the adhesive’s ability to bond to solid, normal weight concrete when anchor holes are drilled using the recommended drill bit diameter and properly cleaned. Allowable Concrete Capacity / Bond Strength working load values have been reduced using a safety factor of 4.0 in Tension and 3.0 in Shear, applied to the Average Ulmate Ulmate values. Average Ulmate values values were determined by physical physical tesng of cured adhesive anchor samples using ASTM A 193 B7 carbon steel threaded rods. In some crical cases, such as life safety applicaons, a safety factor of 10.0 or higher may be necessary. Appropriate safety factors must be determined by the responsible, qualied design professional in charge of the actual product installaon. 2. Allowable Concrete Capacity / Bond Strengthworking load values must be checked against against the Allowable Steel Strength values. values. The lowest value governs as the allowable performance value of the anchor assembly. 3. Tabulated data data is applicable to single anchors in normal weight concrete unaected by potenal EdgeDistance and/or Anchor Spacing reducon factors. Allowable Concrete Capacity / Bond Strength working load values are valid for anchors installed into dry, uncracked concrete aer anchor holes are drilled using a rotary hammer drill and carbide-pped dr ill bits meeng ANSI Standard B212.15. 4. In-service temperature condions should remain relavely constant. The maximum recommended long term, ambient and substrate temperature temperature is 122o F (50o C) and the maximum recommended short term ambient and substrate temperature temperature is 176o F (80o C). Short term ambient and substrate temperatures temperatures are those that occur over brief intervals, such as thermal cycling or temporary temperature uctuaons over a 24 hour period. 5. Linear interpolaon of values is permied between published embedment depths and/or between typical concrete compressive compressive strengths. Extrapolaon of values outside of the range of published Allowable Concrete Capacity / Bond Strength working load values is not permied. 6. As in all applicaons, adhesive anchor performance data must ulmately be interpreted, reviewed and approved by the responsible, qualied design professional in charge of the actual product installaon.


Mixing

1. Remove the twist cap from the top of the cartridge. 2. Reach into the opening at the top of the cartridge with a piler or similar tool and pull thetop of the plastic lm upwards to reveal a metal retaining clip. 3. Cut the plastic lm and open below the metal retaining clip with a utility knife. 4. Ensure that both components within the plastic lm are free to ow prior to inserting cartridge into a standard, good quality caulking gun. ‘A’ component is beige in color and ‘B’ component is black in color. 5. Attach the stactic mixing nozzle


Application

6. Begin dispensing the cartridge ’s contents through the static mixing mixing nozzle. Prior to disdis pensing into the anchor hole, the initial portion of material that exits the end of the nozzle is discarded. 7. VERY IMPORT IMPORTANT! ANT! Visually verify that both components are owing through the static mixing nozzle and mixed adhesive presents a uniform Gray appearance and consistency without streaking before dispensing into the prepared anchor hole. Failure to verify a uniform Gray appearance and consistency may result in an adhesive anchor installation that will not cure properly. SURFACE PREP: 1. Generally, the inside surfaces of an anchor hole need to be as clean, sound, dust-free and dry as possible prior to injection of an anchoring adhesive. A clean, damp surface can be tolerated, but an anchor hole should not contain standing water or have droplets of moisture clinging to the surfaces. Drill an anchor hole into an uncracked, solid concrete substrate with the recommended diameter, carbide-tipped drill bit to the desired or recommended embedment depth using a typical rotary hammer drill. If a carbide-tippe d “core” or diamond “core” bit is used and it leaves a smooth, polished surface on the inside of the anchor hole when the core is removed, then surfaces should be scoured and/or proled with a smaller diameter carbide tipped drill bit. 2. Thoroughly clean the hole in the following sequence: Blow Clean x2. Brush Clean x2. Blow Clean x2. Brush Clean x2. Blow Clean x2.


Application

APPLICATION OF PRODU CT/OBJECT CT/OBJECT:: 3. After anchor hole preparation and cartridge set-up, begin dispensing mixed adhesive beginning at the base or bottom of the anchor hole. 4. Steadily withdraw the tip of the static mixer while dispensing, keeping the tip in the adhesive to reduce and/or eliminate air entrapment. 5. IFill anchor hole until half to two thirds (1/2 to 2/3) of the way way full. Stop dispensing. Release trigger pressure from caulk gun. Scrape tip of static mixer along inside walls of anchor hole to clean tip of excess adhesive while removing.


Application

6. Insert clean, contaminant-free steel threaded thread for anchor installation or clean, rust-free steel rebar for dowel installation. installation. Twist hardhardware while pressing into adhesive-lled anchor hole to ensure thorough wetting of the threads or deformations, and set to full embedment depth. Quickly adjust and position hardware to nal location prior to published Gel Time. 7. Insert the clean threaded bar, free from oil or other release agents, to the bottom of the hole using a back and forth twisting motion ensuring all the threads are thorough ly coated. Adjust to the correct position within the stated working time (see table on page 1). TOOLING AND FINISHING: 8. During insertion of anchor hardware (i.e. steel threaded rod or steel rebar) uncured anchoring adhesive will displace from the entrance of the anchor hole. Installer may opt to smooth the uncured, displaced adhesive around the hardware with a putty knife or similar tool to seal the anchor hole from future moisture inltration. Uncured, displaced adhesive adhesive can also be wiped away with a rag or paper towel and discarded. This option is typically typically taken when a xture will later be mounted with nut and washer onto a steel threaded rod installation.

9. Although still considered good practice, removal of displaced adhesive typically is not critical or necessary when rebar dowels, whose purpose is to permit future concrete placement, are installed. Displaced adhesive that is allowed to cure can only be removed mechanically (e.g. light handheld hammer strikes to chip away).

- Based on actual ambient and substrate temperature conditions, allow sufcient Cure Time to elapse, leav ing adhesive undisturbed prior to loading the anchor. - For steel threaded rod installations, attach xture with a nut and washer. To avoid breaking the fresh bond created, be sure not to overtighten nut beyond the recommended


Sika ® AnchorFix-S Comp. A

Danger Flammable liquid and vapor. May cause cancer. Suspected of damaging fertility or the unborn child. Causes damage to organs (hearing organs) through prolonged or repeated exposure. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open ames/hot surfaces. No smoking. Keep container tightly closed. Ground/bond container and receiving equipment. Use explosion-proof electrical/ ventilating/ lighting/ equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Do not breathe dust/ fume/gas/ mist/ vapors/ spray. Wash Wash skin thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves/ eye protec tion/ face protection. Use personal protective equipment as required. IF ON SKIN (or hair): Take hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. IFexposed or concerned: Get medical advice/ attention. In case of re: Use dry sand, dry chemical or alcoholresistant foam to extinguish. Store in a well-ventilated place. Keep cool. Store locked up. Dispose of contents/ container to an approved waste disposal plant. Contains: Quartz (SiO2) (CAS: 14808-60-7), styrene (CAS: 100-42-5), titanium dioxide (CAS: 13463-67-7).


WARNING! This product contains a chemical known in the State of California to cause cancer. HMIS: *3, 3, 0, X. VOC: 37 VOC: 37 g/l (A+B Combined).

Sika ® AnchorFix-S Comp. B

Warning May cause an allergic skin reaction. Causes serious eye irritation. Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray. Wash skin thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves/ eye protection/ face protection. IF ON SKIN: Wash SKIN: Wash with plenty of soap and water. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical advice/ attention. If eye irritation persists: Get medical advice/ attention. Wash contaminated clothing before reuse. Dispose of con tents/ container to an approved waste disposal plant. Contains: dibenzoyl peroxide (CAS: 94-36-0). HMIS: *2, HMIS: *2, 1, 0, X. VOC: 37 VOC: 37 g/l (A+B Combined).

PRIOR TO EACH USE OF ANY SIKA PRODUCT, THE USER MUST ALWAYS READ AND FOLLOW THE WARNINGS AND INSTRUCTIONS ON THE PRODUCT’S MOST CURRENT PRODUCT DATA SHEET, PRODUCT LABEL AND SAFETY DATA SHEET WHICH ARE AVAILABLE ONLINE AT HTTP://USA.SIKA.COM/ OR BY CALLING SIKA’S TECHNICAL SERVICE DEPARTMENT AT 800.933.7452 NOTHING CONTAINED IN ANY SIKA MATERIALS RELIEVES THE USER OF THE OBLIGATION TO READ AND FOLLOW THE WARNINGS AND INSTRUCTIONS FOR EACH SIKA PRODUCT AS SET FORTH IN THE CURRENT PRODUCT DATA SHEET, PRODUCT LABEL AND SAFETY DATA SHEET PRIOR TO PRODUCT USE. KEEP CONTAINER TIGHTLY CLOSED. KEEP OUT OF REACH OF CHILDREN. NOT FOR INTERNA L CONSUMPTION. FOR INDUSTRIAL USE ON LY. FOR PROFESSIONAL USE ONLY.

For further information and advice regarding transportation, handling, storage and disposal of chemical products, users should refer to the actual Safety Data Sheets containing physical, ecological, toxicological and other safety related data. Read the current actual Safety Data Sheet before using the product. In case of emergency emergency,, call CHEMTREC at 1-800-424-9300, International 703-527-3887. Prior to each use of any Sika product, the user must always read and follow the warnings and instructions on the product’s most current Product Data Sheet, product label and Safety Data Sheet which are available online at http://usa.sika.com/ or by calling Sika’s Technical Service Department at 800-933-7452. Nothing contained in any Sika materials relieves the user of the obligation to read and follow the warnings and instruction for each Sika product as set forth in the current Product Data Sheet, product label and Safety Data Sheet prior to product use. SIKA warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties on the current Product Data Sheet if used as directed within shelf life. User determines suitability of product for intended use and assumes all risks. Buyer’s sole remedy shall be limited to the purchase price or replacement of product exclusive of labor or cost of labor. NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL APPLY INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES. SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY OTHERS. SALE OF SIKA PRODUCTS ARE SUBJECT SIKA’S TERMS AND CONDITIONS OF SALE AVAILABLE AT HTTP://USA.SIKA.COM/ OR BY CALLING 201-933-8800.

Visit our website at usa.sika.com 1-800-933-SIKA NATIONWIDE Regional Information and Sales Centers. For the location of your nearest Sika sales ofce, contact your regional center. Sika Corporation Sika Canada Inc. Sika Mexicana S.A. de C.V. 201 Polito Avenue 601 Delmar Avenue Carretera Libre Celaya Km. 8.5 Lyndhurst, NJ 07071 Pointe Claire Fracc. Industrial Balvanera Phone: 800-933-7452 Quebec H9R 4A9 Corregidora, Queretaro Fax: 201-933-6225 Phone: 514-697-2610 C.P.. 76920 C.P Fax: 514-694-2792 Phone: 52 442 2385800 Fax: 52 442 2250537 ISO 9001

Certificate # FM 69711

RC 14001

Certificate # RC510999

PDS Sika AnchorFix S

Recommend Documents