MALAYSIAN STANDARDS SECTORIAL CATALOGUE
2007
No. 4 ELECTRICAL ENGINEERING & ELECTRONICS
Department of Standards Malaysia Ministry of Science, Sci ence, Technology Technology & Innovat Innovation ion Level 1 & 2, Block C4, Complex C Federal Government Administrative Centre 62502 Putrajaya, MALAYSIA Tel : 603-8885 6 03-8885 8000 Fax : 603-8888 5060 E-Mail :
[email protected] info@standardsmalay sia.gov.my http://www.standardsmalaysia.gov.my
MALAYSIAN STANDARDS SECTORIAL CATALOGUE
2007
No. 4 ELECTRICAL ENGINEERING & ELECTRONICS
Department of Standards Malaysia Ministry of Science, Sci ence, Technology Technology & Innovat Innovation ion Level 1 & 2, Block C4, Complex C Federal Government Administrative Centre 62502 Putrajaya, MALAYSIA Tel : 603-8885 6 03-8885 8000 Fax : 603-8888 5060 E-Mail :
[email protected] info@standardsmalay sia.gov.my http://www.standardsmalaysia.gov.my
INTRODUCTION The Department of Standards Malaysia (Standards Malaysia) is the national standardisation and accreditation body. The main function of the Department is to foster and promote standards, standardisation and accreditation as a means of advancing the national economy, promoting industrial efficiency and development, benefiting the health and safety of the public, protecting the consumers, facilitating domestic and international trade and furthering international cooperation in relation to standards and standardisation. Malaysian Standards are developed through consensus by committees which comprise of balanced representation of producers, users, users , consumers and others with relevant interests, as may be appropriate to the subject in hand. These standards where appropriate are adoption of international standards. Approval of a standard as a Malaysian Standard is governed by the Standards of Malaysia Act 1996 (Act 549). Malaysian Standards are reviewed periodically. The use of Malaysian Standard is voluntary except in so far as they are made mandatory by regulatory authorities by means of regulations, local by-laws or any other similar ways. The Department of Standards Malaysia appoints SIRIM Berhad as the agent to develop Malaysian Standards. The Industry Standards Committees (ISCs) established by SIRIM Berhad are responsible for the development of Malaysian Standards in their respective areas, as follows: ISC A ISC B ISC C ISC D ISC E ISC F ISC G ISC H ISC J ISC K ISC L ISC M ISC N ISC W NC Y NC Z
-
Food and Agriculture Chemicals and Materials Consumer Products, Personal Safety and Services Building and Civil Engineering Electrotechnical Mechanical Engineering Information Technology, Communications and Multimedia Petroleum and Gas Plastics and Plastics Products Packaging and Distribution Road Vehicles Fire Safety and Prevention Rubber and Rubber Products Occupational Health and Safety Quality Management and Quality Assurance Environmental Standards
More than 100 standards development committees involving more than 1500 individuals, have been established under the ISCs.
(ii)
Malaysian Standards Sectorial Catalogue 2007
This sectorial catalogue lists as at August 2007, Malaysian standards that have been established on product specifications, codes of practice, terminologies, guides and method of test on selected sectors. New standards, revisions, amendments, addenda, errata and reconfirmed standards as well as standards that have been withdrawn are published bi-monthly in the SIRIM Berhad’s newsletter Standards and Quality News. An online sistem is available for searching and online purchasing. Payment can be made by credit card. The system is called the MS Online System and can be accessed at http://www.msonline.gov.my. The MS Online system contains over 4,000 Malaysian standards on all sectors. List of Sectorial Catalogue 2007 1. Quality Management System, Environmental Management System & Safety and Health Protection 2. Health Care Technology, Metrology and Measurement. Testing 3. Mechanical and Fluid System and Components. Manufacturing Engineering, Energy and Heat Transfer Engineering 4. Electrical Engineering & Electronics 5. Telecommunication, Information Technology. Office Equipment 6. Road Vehicles Engineering, Material Handling Equipment, Packaging & Distribution of Goods. 7. Textile and Leather Technology and Clothing Industry 8. Agriculture and Food Technology 9. Chemical Technology, Technology, Mining and Minerals, Petroleum and related technology & Metallurgy 10. Wood Technology, echnology, Glass & Ceramics Industries, Paper Technology and Paints & Colour Industries 11. Rubber & Plastics Industries 12. Constructions Materials & Building. Civil Engineering. Housekeeping. Entertainment. Sports.
ABBREVIATIONS MS
: Mala Malays ysia ian n Sta Stand ndar ard d
MS ISO
: Malaysian Malaysian Standard Standard which is is identical identical to International International Organization Organization for Standardization (ISO) Standard. The numbering of the standard is identical to that of the ISO Standard except for the prefix.
MS ISO/IEC
: Malaysian Malaysian Stand Standard ard which which is identica identicall to the Joint Joint ISO and and IEC Stand Standard. ard. The The numbering of the standard is identical to that of the ISO/IEC Standard except for the prefix.
MS.....(P)
: Prov Provis isio iona nall Stan Standa dard rd
Malaysian Standard which is adopted/adapted from international, regional or foreign national standard without undergoing standards development committee deliberations due to its urgent need, as identified by the Department of Standards Malaysia. Provisional Standards are identified by a letter “P” following the MS number.
(iii)
SUBJECT STRUCTURE ACCORDING TO INTERNATIONAL CLASSIFICATION OF STANDARDS
01.
Generalities. Terminologies. Standardization
61.
Clothing Industry.
03.
Sociology. Services. Company Organization and Management. Administration. Transport.
65.
Agriculture.
67.
Food Technology.
07.
Mathematics. Natural Sciences. 71.
Chemical Technology.
73.
Mining and Minerals.
11.
Health Care Technology.
13.
Environment. Health Protection. Safety 75.
Petroleum and Related Technologies.
17.
Metrology and Measurement. Physical Phenomena
77.
Metallurgy.
19.
Testing.
79.
Wood Technology.
21.
Mechanical Systems and Components for General Use.
81.
Glass and Ceramics Industries.
83.
Rubber and Plastics Industries.
Fluid Systems and Components for General Use.
85.
Paper Technology.
25.
Manufacturing Engineering.
87.
Paint and Colour Industries.
27.
Energy and Heat Transfer Engineering.
91.
Construction Materials and Building.
31.
Electronics.
93.
Civil Engineering.
33.
Telecommunications. Audio and Video Engineering.
95.
Military Engineering.
97.
Domestics and Commercial Equipment. Entertainment. Sports.
23.
35.
Information Technology. Office Machines.
37.
Image Technology.
39.
Precision Mechanics. Jewellery.
43.
Road Vehicles Engineering.
45.
Railway Engineering.
47.
Shipbuilding and Marine Structures.
49.
Aircraft and Space Vehicle Engineering.
53.
Materials Handling Equipment.
55.
Packaging and Distribution of Goods.
59.
Textile and Leather Technology.
(iv)
CONTENTS Page Introduction ------------------------------------------------------------------------------------------------------------------------
(ii) Malaysian Standards Sectorial Catalogue -------------------------------------------------------------------------------(iii) Abbreviation -----------------------------------------------------------------------------------------------------------------------(iii) Subject Structure by ICS -------------------------------------------------------------------------------------------------------- (iv)
ELECTRICAL ENGINEERING Electrical engineering in general --------------------------------------------------------------------------------------------Insulating fluids in general ----------------------------------------------------------------------------------------------------Conducting materials -----------------------------------------------------------------------------------------------------------Electrical wire and cables -----------------------------------------------------------------------------------------------------Wires --------------------------------------------------------------------------------------------------------------------------------Cables ------------------------------------------------------------------------------------------------------------------------------Electrical and electromechanical components --------------------------------------------------------------------------Electrical accessories ---------------------------------------------------------------------------------------------------------Conduits for electrical purposes ---------------------------------------------------------------------------------------------Plugs, sockets outlets, couplers ---------------------------------------------------------------------------------------------Switches ----------------------------------------------------------------------------------------------------------------------------Fuses and other overcurrent protection devices ------------------------------------------------------------------------Switchgear and controlgear ---------------------------------------------------------------------------------------------------High voltage switchgear and controlgear ----------------------------------------------------------------------------------Low voltage switchgear and controlgear ----------------------------------------------------------------------------------Lamps and related equipment -----------------------------------------------------------------------------------------------Lamps in general ----------------------------------------------------------------------------------------------------------------Lamp caps and holders --------------------------------------------------------------------------------------------------------Incandescent lamps -------------------------------------------------------------------------------------------------------------Fluorescent lamps. Discharge lamps --------------------------------------------------------------------------------------Luminaires -------------------------------------------------------------------------------------------------------------------------Other standards related to lamps -------------------------------------------------------------------------------------------Rotating machinery in general -----------------------------------------------------------------------------------------------Generating sets ------------------------------------------------------------------ -----------------------------------------------Transformers. Reactors ------------------------------------------------------------------------------------------------------Rectifier. Converters. Stabilized power supply ---------------------------------------------------------------------------Galvanic cells and batteries in general ------------------------------------------------------------------------------------Primary cells and batteries --------------------------------------------------------------------------------------------------- Acid secondary cells and batteries ------------------------------------------------------------------------------------------Power transmission and distribution networks in general -----------------------------------------------------------Substations. Surge arresters -------------------------------------------------------------------------------------------------Control equipment for electric power systems ---------------------------------------------------------------------------Electrical installations for outdoor use -------------------------------------------------------------------------------------Electrical apparatus for explosive atmospheres -------------------------------------------------------------------------Other electrical equipment for working in special conditions ---------------------------------------------------------
1 3 3 3 4 5 8 9 9 10 11 12 13 14 14 15 15 16 17 18 19 21 22 22 23 24 24 25 25 25 25 26 26 26 28
ELECTRONICS Electronic components in general -------------------------------------------------------------------------------------------Resistors ---------------------------------------------------------------------------------------------------------------------------Resistors in general ------------------------------------------------------------------------------------------------------------Fixed resistors --------------------------------------------------------------------------------------------------------------------Capacitors -------------------------------------------------------------------------------------------------------------------------Capacitors in general ----------------------------------------------------------------------------------------------------------Diodes ------------------------------------------------------------------------------------------------------------------------------Electronic tubes ------------------------------------------------------------------------------------------------------------------Switches -----------------------------------------------------------------------------------------------------------------------------
Numerical Listing ---------------------------------------------------------------------------------------------------Index -------------------------------------------------------------------------------------------------------------------Order Form ------------------------------------------------------------------------------------------------------------
(v)
29 29 29 29 29 29 29 30 30
31 35 41
29. ELECTRICAL ENGINEERING 29.020
MS 1487 : 1999 Electrotechnical vocabulary : Chapter 121 : Electromagnetism Gives electrotechnical definitions related to electromagnetism.
Electrical engineering in general
Price RM30 MS 406 : 1996 Specification for voltages and frequency for alternating current transmission and distribution system (Second revision). This revised Malaysian Standard covers the voltages and frequency recommended for alternating-current transmission and distribution systems. This standard shall supersede MS 406 : 1989. Price RM10
MS 1936 : 2006 Electrical installations of building – Guide to MS IEC 60364 This standard provides guidelines on the use of MS IEC 60364, Electrical installation of buildings Price RM100
MS 472 : Part 2 : Sec. 2.9 : 1983 Specification for testing and approval of household and similar appliances : Part 2 : Section 2.9 : Particular requirements for rice cooker. Specifies requirements for rice cooker for use in household and does not apply to commercial rice cooker. Should be read in conjunction with MS 472 : Part 1. Price RM10 MS 472 : Part 3 : Sec. 3.1 : 1986 Specification for testing and approval of household and similar appliances : Part 3 : Complete particular specifications : Section 3.1 : Stationary instantaneous water heaters. This standard specifies requirements for electric stationary instantaneous water heaters for heatin g water to a temperature below its boiling point for household and similar purposes. Both sheathed and bare heating element types are covered. Price RM100 MS 860 : Part 1 : 1983 Specification for power supply units for extra low voltage output : Part 1: Units for indoor use. Provides definitions, classification, ratings, construction, output and test methods of various safety requirements for current reducing power units for operating toys using electric supply. Price RM20
MS CISPR 19 : 2000 Guidance on the use of the substitution method for measurements of radiation from microwave ovens for frequencies above 1 GHz Describes a method of measurement for small microwave ovens (largest dimension less than 1 m) and a separate method of measurement for large microwave ovens (largest dimension exceeding 1m). Price RM20 MS IEC 60038 : 2006 IEC standard voltages This standard applies to – a.c transmission, distribution and utilization systems and equioment for use in such systems with standard frequencies 50 Hz having a nominal voltage above 100 V. – a.c and d.c traction systems; - a.c and d.c equipment having nominal voltages below 120 V a.c or below 750 V d.c, the a.c voltages being intended (but not exclusively) for 50 Hz and 60 Hz applications, such equipment covers batteries (from primary or secondary cells), other power supply devices (a.c or d.c) electrical equipment (including industrial and communication) and appliances. Price RM20 MS IEC 60050-426 : 2004 International electrotechnical vocabulary – Chapter 426 : Electrical apparatus for explosive atmospheres Price RM40
MS 944 : 1984 Specification for maximum demand indicators class 1.0. Covers definitions, classification, mechanical and electrical requirements, marking, accuracy for above indicators intended to operate as attachments to watthour meters or varhour meters. Price RM20
MS IEC 60364-7-702 : 2003 Electrical installations of buildings – Part 7 : Requirements for special installations – Section 702 : Swimming pools and other basins (First revision). This Malaysian Standard applies to the basins of swimming pools, the basins of fountains and the basins of paddling pools. Price RM30
MS 946 : 1984 Specification for residual current operated protective device. Definitions, service conditions, rating and marking, design and construction and type and routine test are outlined. Rated voltage of device does not exceed 660 Volts, while rated current does not exceed 125 amp. at rated frequency not exceeding 400Hz. Price RM30
MS 1144 : 1998 Specification for general requirements for electrical accessories. Covers requirements for electrical wiring accessories for installation not specifically covered by other Malaysian Standards for use in single phase a.c. or d.c. circuits for voltages between conductors, exceeding extra-low voltage but not exceeding 250 V and current not exceeding 45A. Price RM70
1
MS IEC 60529 : 2005 Degrees of protection provided by enclosures (IP code) (First revision) This Malaysian Standard applies to the classification of degrees of protection provided by enclosures for electrical equipment with rated voltage not exceeding 72.5 kV. Price RM60 MS IEC 61000-3-5 : 2000 Electromagnetic compatibility (EMC) - Part 3 : Limits – Section 5 : Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16 A Concerns with the emission of disturbances due to voltage fluctuations and flicker. Price RM20 MS IEC 61000-4-2 : 2002 Electromagnetic compatibility (EMC) Part 4 : Testing and measurement techniques Section 2 : Electrostatic discharge immunity test Basic EMC publication Relates to the immunity requirements and test methods for electrical and electronic equipment subjected to static electricity discharges, from operators directly, and to adjacent objects. The standard also defines ranges of test levels which relates to different environmental and installation conditions and establishes test procedure. This standard is identical with IEC 61000-4-2 : 1995. Price RM40
MS IEC 61000-4-6 : 2000 Electromagnetic compatibility (EMC) - Part 4 : Testing and measurement techniques - Section 6: Immunity to conducted disturbances, induced by radio-frequency fields Relates to the conducted immunity requirements of electrical and electronic equipment to electromagnetic disturbances coming from intended radio-frequency (RF) transmitters in the frequency range 9 kHz up to 80 MHz. Equipment not having at least one conducting cable (such as mains supply signal line or earth connection) which can couple the equipment to the disturbing RF fields is excluded. This standard is identical with IEC 61000-4-6 : 1996. Price RM50 MS IEC 61000-4-8 : 2000 Electromagnetic compatibility (EMC) Part 4 : Testing and measurement techniques Section 8 : Power frequency magnetic field immunity test Basic EMC publication Relates to the immunity requirements of equipment, only under operational conditions, to magnetic disturbances at power frequency related to: - residential and commercial locations;- industrial installation and power plants; - medium voltage and high voltage sub-stations. This standard does not consider disturbances due to capacitive or inductive coupling in cables or other parts of the field installation. This standard is identical with IEC 61000-4-8 : 1993. Price RM40 MS IEC 61000-4-10 : 2000 Electromagnetic compatibility (EMC) - Part 4 : Testing and measurement techniques - Section 10 : Damped oscillatory magnetic field immunity test Basic EMC publication Relates to the immunity requirements of equipment, only under operational conditions, to damped oscillatory magnetic disturbances related to medium voltage and high voltage sub-stations. This standard does not consider disturbance due to capacitive or inductive coupling in cables or other parts of the field installation. This standard is identical with IEC 61000-4-10 : 1993.
MS IEC 61000-4-3 : 2001 Electromagnetic compatibility (EMC) - Part 4 : Testing and measurement techniques - Section 3 : Radiated, radio-frequency, electromagnetic field immunity test (First revision). This section of MS IEC 1000-4 is applicable to the immunity of electrical and electronic equipment to radiated electromagnetic energy. It establishes test levels and the required test procedures. Price RM40
Price RM40 MS IEC 61000-4-4 : 2000 Electromagnetic compatibility (EMC) Part 4 : Testing and measurement techniques Section 4 : Electrical fast transient/ burst immunity test Basic EMC publication Relates to the immunity requirements and test methods for electrical and electronic equipment to repetitive electrical fast transients. Additionally defines ranges of test levels and establishes test procedures. The object of this standard is to establish a common and reproducible basis for evaluating the performance of electrical and electronic equipment when subjected to repetitive fast transients (burst), on supply, signal and control parts. This standard is identical with IEC 61000-4-4 : 1995. Price RM40
MS IEC 61000-4-11 : 2000 Electromagnetic compatibility (EMC) - Part 4 : Testing and measuring techniques - Section 11 : Voltage dips, short interruptions and voltage variations immunity tests Defines the immunity test methods and range of preferred test l evels for electrical and electronic equipment connected to low-voltage power supply networks for voltages disp, short interruptions, and voltage variations. The standard applies to electrical and electronic equipment having a rate d input current not exceedi ng 16 A per phase. It does not apply to electrical and electronic equipment for connection to d.c. networks or 400 Hz a.c networks. This standard is identical with IEC 61000-4-11 : 1994. Price RM30
MS IEC 61000-4-5 : 2000 Electromagnetic compatibility (EMC) - Part 4 : Testing and measurement techniques - Section 5 : Surge immunity test Relates to the immunity requirements, tests methods, and range of recommended test levels for equipment to unidirectional surges caused by overvoltages from switching and lightning transients. Several test levels are defined which relate to different environment and installation conditions. These requirements are developed for and are applicable to electrical and electronic equipment. Establishes a common reference for evaluating the performance of equipment when subjected to high-energy disturbances on the power and interconnection lines. This standard is identical with IEC 61000-4-5 : 1995. Price RM50
MS IEC 61000-4-12 : 2000 Electromagnetic compatibility (EMC) Part 4 : Testing and measurement techniques - Section 12 : Oscillatory waves immunity test Basic EMC publication Relates to the immunity requirements and test methods for electrical and electronic equipment, under operational conditions, to oscillatory waves represented by: a) no-repetitive damped oscillatory transients (ring wave) occurring in low-voltage power, control and signal lines supplied by public and non-public networks. b) repetitive damped oscillatory waves occurring mainly in power, control and signal cables installed in high voltage and medium voltage (HV/MV) stations. This standard is identical with IEC 61000-4-12 : 1995. Price RM50
2
MS IEC 61000-4-16 : 2000 Electromagnetic compatibility (EMC) – Part 4-16 : Testing and measurement techniques – Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 KHz Relates to the immunity requirements and test methods for electrical and electronic equipment to conducted common mode disturbances in the range d.c to 150 kHz. The object of this standard is to establish a common and reproducible basis for testing electrical and electronic equipment with the application of common mode disturbances to power supply, control, signal and communication parts. This standard is identical with IEC 61000-4-16 : 1998. Price RM40
This Malaysian Standard specifies the requ irements and test methods for carbon steel tubes to be used for machinery, automobiles, bicycles, furniture, appliances and other machine parts. Price RM20 MS 1863 : 2005 Cold headed rivets – Specification This Malaysian Standard specifies requirements for cold headed rivets made of steel, brass, copper and aluminium for general use. Price RM20
29.050
MS IEC 61000-6-1 : 2000 Electromagnetic compatibility (EMC) – Part 6 : Generic standards – Section 1 : Immunity for residential, commercial and lightindustrial environments Applies to electrical and electronic apparatus intended for use in the residential, commercial and light-industrial environment, as described in clause 4, for which no dedicated product or product-family emission standard exists designed to radiate. Disturbances in the frequency range O Hz to 400 GHz are covered. This standard is identical with IEC 61000-6-1 : 1997. Price RM30
MS 69 : 1995 Specification for conductors in insulated cables and cords (Second revision). This Malaysian Standard specifies the nominal cross-sectional areas and requirements, including numbers and sizes of wire and resistance values, for conductors in electric cables and cords of a wide range of types. These conductors include solid and stranded copper and aluminium conductors’ ’in cables for fixed installations and flexible copper conductors’.
MS IEC 61000-6-3 : 2000 Electromagnetic compatibility (EMC) – Part 6 : Generic standards – Section 3 : Emission standard for residential, commercial and light-industrial environments Applies to electrical and electronic apparatus intended for use in the residential, commercial and light industrial environment, as described in Clause 5, for which no dedicated product or product-family emission standard exists. Apparatus designed to radiate electromagnetic energy for radio communication purposes is excluded from the standard. Disturbances in the frequency range 0Hz to 4000 GHz are covered. This Standard is identical with IEC 61000-6-3 : 1996. Price RM20
Price RM30 MS 1142 : 1989 Specification for hard-drawn copper and power copper-cadmium conductors for oven-head transmission purposes. Specifies requirements for hard-drawn copper and copper cadmium solid and stranded circular conductors for overhead power transmission systems. Price RM20 MS 1143 : 1989 Specification for aluminium alloy stranded conductor for overhead power transmission. Covers requirements for heat-treated aluminium-magnesium-silicon alloy stranded conductors for overhead power, transmission; values for physical properties, sizes of wires and of stranded conductors; tolerances on dimensions, mechanical properties and electrical resistivity; modules of elasticity and code names for use when ordering. Price RM20
MS IEC 61000-6-4 : 2000 Electromagnetic compatibility (EMC) - Part 6 :Generic standards - Section 4 : Emission standard for industrial environments Applies to electrical and electronic apparatus intended for use in the industrial environment, as described in Clause 5, for which no dedicated product or product-family emission standard exists. Apparatus designed to radiate electromagnetic energy for radio communication purposes is excluded from this standard. Disturbances in the frequency range 0Hz to 400 GHz are covered. Fault conditioning of apparatus are not taken into account. Also applies to apparatus intended to operate in industrial locations or in proximity to industrial power installations. This standard is identical with IEC 61000-6-4 : 1997. Price RM20
29.035.01
29.060
Electrical wires and cables
MS 280 : 1975 Specification for copper for electrical purposes, wire for general electrical purposes for insulated cables and flexible cords. Specifies requirements for high conductivity, plain or tinned, annealed or hard copper wire with diameter from 0.05 mm up to and including 6.6. mm for general electrical purposes and for use in insulated cables and flexible cords.
Insulating materials in general
MS 938 : 1984 Specification for classification of materials for the insulation of electrical machinery and apparatus in relation to their thermal stability in service. Classifies insulation into seven classes according to materials and details out information on ratings, assessment of thermal stability and application. Price RM20
29.040.01
Conducting materials
Price RM20 MS 1540 : 2002 Specification for the material, marking and dimensions of crimp type cable lugs for use with copper conductors in low voltage applications This Malaysian Standard specifies the overall installed dimensions of crimp type cable lugs (copper conductors) for low voltage applications. Price RM10
Insulating fluids in general
MS 1862 : 2005 Carbon steel tubes for machine structural purposes – Specification
3
MS 1779 : 2005 Crimp type cable links as trough-connectors for and with stranded (non-compact) copper conductors in low voltage applications – Specification for the materials, marking and dimensions. This Malaysian Standard specifies the overall installed dimensions of crimp type cable links as trough-connectors for and with copper conductors in low voltage applications. Price RM10
29.060.01
Electrical wires and cables in general
MS 1777 : Part 2-1 : 2006 Cable trunking and ducting systems for electrical installations – Part 2 : Particular requirements – Section 1 : Cable trunking and ducting systems intended for mounting on walls or ceilings Replacement ; This section of IEC 1084-2 specifies requirements for cable trunking and ducting systems intended for mounting on walls or ceilings. The cable trunking and dutting systems accommodate and where necessary segregate conductors, cables or cords and other electrical equipment. Price RM20
MS 1838 : 2005 Heavy duty crimp type cable lugs for use with XLPE insulated and circular compact copper conductors in single and multi core power cable applications up to 36 Kv – Specification for the material, marking and dimensions This Malaysian Standard specifies the construction and the overall installed dimensions of heavy duty crimp type cable lugs for use with XLPE insulated and circular compact copper conductors in single and multi core power cable applications up to 36 kV. Price RM10
MS 1777 : Part 2-2 : 2006 Cable trunking and ducting systems for electrical installations – Part 2-2 : Particular requirements – Cable trunking and cable ducting systems intended underfloor and flushfloor installations This clause of Part 1 is replaced by : This part of IEC 61084 specifies requirements for cable trunking and cable ducting systems intended for the accommodation and where necessary for the segregation of conductors, cables or cords and/or other electrical equipment in electrical installations. Price RM30
MS 2100 : 2006 Electric cable and wire 600/1000 (Um=1200) V single core PVC insulated cable – Non-armoured This Malaysian Standard specifies construction, dimension and test requirements of PVC insulated, PVC sheathed single core cables, nonarmoured for operation at rated voltage 600/1000 (Um=1200) V. Price RM20
29.060.10
MS 2101 : 2006 Electric cable and wire 600/1000 (Um=1200) V single core PVC insulated cable – Armoured This Malaysian Standard specifies construction, dimension and test requirements of PVC insulated, PVC sheathed single core cables, armoured for operation at rated voltage 600/1000 (Um=1200) V. Price RM20
Wires
MS 435 : 1976 Specification for wrought aluminium for electrical purposes wire. Price RM20 MS 528 : 1977 Specification for stranded wire ropes, fibre components : Characteristics and tests. Price RM10
MS 2102 : 2006 Electric cable and wire 600/1000 (Um=1200) V multi core PVC insulated cable – Non - Armoured This Malaysian Standard specifies construction, dimension and test requirements of PVC insulated, PVC sheathed multi-core cables, non-armoured for operation at rated voltage 600/1000 (1200) V. Price RM20
MS 529 : 1977 Specification for stranded wire ropes for mine hoisting impregnating compounds and lubricants - characteristics and tests. Price RM20
MS 2103 : 2006 Electric cable and wire 600/1000 (Um=1200) V multi core PVC insulated cable – Armoured This Malaysian Standard specifies construction, dimension and test requirements of PVC insulated, PVC sheathed multi-core cables, armoured for operation at rated voltage 600/1000 (1200) V. Price RM20
MS 550 : 1978 Round steel wire for ropes. Covers general requirements and test methods applicable to three types general purpose round steel wire of diameters 0.19 m and 5 mm and two types of high duty wire of diameters between 0.8 mm and 3.5 mm. Price RM30
MS 2104 : 2006 Electric cable and wire 600/1000 (Um=1200) V single core XLPE insulated cable – Non - Armoured This Malaysian Standard specifies construction, dimension and test requirements of cross-linked polyethylene (XLPE) insulated single core cables, non - armoured for operation at rated voltage 600/1000 (1200) V. Price RM20
MS 551 : 1978 Specification for wire ropes for cranes, excavators and general engineering purposes. Specifies material, manufacture, inspection, test and acceptance. Price RM40 MS 754 : 1981 Specification for stranded wire ropes - Technical delivery requirements. Outlines those properties which forms a basis for acceptance of stranded wire ropes and their component part. Price RM20
MS IEC 61540 : 2003 Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs) This Malaysian Standard applies to portable devices for household and similar uses [hereafter referred to as portable residual current devices (PRCDs)] consisting of a plug, a residual current device (RCD) and one or more socket-outlets or a provision for connection, functionally independent of, or functionally dependent on, line voltage . Price RM120
4
MS 796 : 1982 Specification for small wire ropes. For ropes 7mm and smaller. Specifies requirements on mechanical properties, manufacture and acceptance. Price RM20
29.060.20
Cables
MS 69 : 1995 Specification for conductors in insulated cables and cords (Second revision). This Malaysian Standard specifies th e nominal cross-sectional areas and requirements, including numbers and sizes of wire and resistance values, for conductors in electric cables and cords of a wide range of types. These conductors include solid and stranded copper and aluminium conductors’ ’in cables for fixed installations and flexible copper conductors’.
MS 824 : 1983 Specification for thimbles for wire ropes. Specifies materials and dimensions of ordinary reeving and solid types thimbles. Also includes form and dimensions, workmanship, finish and inspection. Price RM20 MS 1092 : 1987 Specification for low carbon steel wire rods. Specifies low carbon steel wire rods to be used for the manufacture of iron wires, armoured cable wires, galvanized iron wire strands, telegraph wires, etc. This standard does not apply to wire rods for core wires of coated electrode. Price RM10
Price RM30 MS 136 : 1995 Specification for PVC insulated cables (non-armoured) for electric power and lighting (Second revision). This Malaysian Standard specifies requirements and dimensions for non-armoured PVC-insulated cables for operation at voltages up to and including 450V to earth and 760V between conductors. Price RM40
MS 1093 : 1987 Specification for high carbon steel wire rods. Specifies high carbon steel wire rods to be used for the manufacture of high carbon steel wires, oil tempered wires, high carbon steel wires for prestressed concrete, galvanized steel wire strands, steel wire ropes etc. Price RM10
MS 137 : 1973 Specification for PVC insulated cables for switchgear and control gear wiring. Specifies requirements for single-core cables, including flexible cables used for the small wiring of switches, meters relays and instrument panels of power switchgear. Classifies cables into 2 types according to test properties. Details on construction and overall dimensions, electrical tests and measurement of insulation thickness are given. Price RM20
MS 1237 : 1991 Specification for general purpose galvanized steel wire strand. This Malaysian Standard specifies requirements for seven tensile strength grades of galvanized steel wire strand in sizes from 1.7 mm to 23.8 mm diameter, intended for a variety of purposes including railway signalling strand. Price RM20
MS 138 : 1995 specification for PVC-insulated and sheath of electric cables (Second revision). This Malaysian Standard specifies the physical and electrical requirements for the types of PVC insulation and sheath of electric cables given in Table 1 in MS 1095 or in the appendices of this standard. This standard shall supersedes MS 138 :1987. Price RM20
MS 1238 : 1991 Specification for galvanized steel wire for aluminium conductors, steel-reinforced. This Malaysian Standard specifies the requirements for galvanized steel wire, as supplied by the wire manufacture, for the manufacturer of aluminium conductors, steel reinforced in accordance with MS 1198. Price RM10
MS 140 : 1987 Specification for insulated flexible cords and cables (First revision). Specifies requirements and dimensions for flexible cords and cables for operation at voltages up to and including 450V earth and 750V between conductors. Price RM60
MS 1239 : 1991 Specification for galvanized low carbon steel wire for armouring cables. This Malaysian Standard specifies requirements for galvanized round low carbon steel wire, primarily for armouring of land cables, in diameters ranging from 0.30 mm to 4.0 mm. The nominal wire diameters given in table 1 are the preferred sizes and are in the R 40 series in accordance with BS 4391. The material used for the wire shall be the wire rods conforming to MS 1092. Price RM10
MS 274 : 1995 specification for PVC insulated cables for electricity supply (Second revision). This Malaysian Standard specifies the requirement and dimensions for PVC-insulated cables for operation at nominal voltages up to and including 1900V to armour or earth and 3300V between conductors. Price RM60
MS 1240 : 1991 Specification for galvanized steel wire for armouring submarines cables. This Malaysian Standard specifies requirements for galvanized round steel wire in diameters ranging from 2.12 mm to 8.50 mm for armouring submarine cables. The nominal wire diameters specified in tables 1, 2 and 3 are the preferred sizes, and are in the R 40 series or BS 4398. Price RM20
MS 276 : 1987 Specification for rubber insulation and sheath of electric cables (First revision). Covers specification compositions, colour and requirements for tensile strength and elongation at break, water absorption, insulation resistance constant, tear resistance, ozone resistance, oil resistance and permittivity. Price RM20
5
MS 278 : 1987 Specification for rubber insulated cables for electric power and lighting (First revision). Specifies requirements for the construction electric properties, mechanical properties and dimensions of non-armoured rubberinsulated cables and flexible cables for operation at voltages up to and including 451 V ac to earth and 750V ac between conductors. Price RM40
MS IEC 60287-2-1 : 2001 Electric cables - Calculation of the current rating - Part 2 : Thermal resistance - Section 1 : Calculation of thermal resistance This section of IEC 60287 is solely applicable to the conditions of steady-state operation of cables at all alternating voltages, and direct voltages up to 5 kV, buried directly in the ground, in ducts in troughs or in steel pipes, both with and without partial drying-out of the soil, as well as cables in air. Price RM40
MS 434 : 1976 Specification for wrought aluminium for electrical purposes solid conductors for insulated cables. Specifies requirements for circular solid and 2- 3-, and 4- core shaped solid conductors in a range of standard sizes from 16 mm squared up to and including 300 mm squared. Price RM20
MS IEC 60287-2-2 : 2001 Electric cables - Calculation of the current rating - Part 2 : Thermal resistance - Section 2 : A method for calculating reduction factors for groups of cables in free air, protected from solar radiation The method described in this Malaysian Standard is applicable to any type of cable and group running horizontally, provided that the cables are of equal diameter and emit equal losses. Price RM30
MS 766 : Part 1 : 1982 Low-frequency communication cables and wires with PVC insulation and PVC sheath : Part 1 : General tests and measuring methods. Establishes uniform requirements for electrical, climatic and mechanical properties and test methods. Price RM20
MS IEC 60287-3-2 : 2003 Electric cables – Calculation of the current rating – Part 3 : Sections on operating conditions – Section 2: Economic optimization of power cable size. This Malaysian Standard is identical with IEC 60287-3-2:1995 and its Amendment 1:1996. This Malaysian Standard deals solely with the economic choice of conductor size based on joul e losses. Voltage dependent losses have not been considered. Price RM50
MS 1095 : 1987 Method or test for insulation and sheaths of electric cables. Describes methods of test used for testing extruded polymeric insulation and sheaths of electric cables. Price RM80
MS IEC 60331-11 : 2001 Tests for electric cables under fire conditions - Circuit integrity - Part 11 : Apparatus - Fire alone at a flame temperature of at least 750°C This part of MS IEC 60331 specifies the test apparatus to be used for testing cables required to maintain circuit integrity when subject to fire alone where the test condition is based upon a flame with a controlled heat output corresponding to a temperature of at least 750°C. Price RM30
MS IEC 60183 : 2003 Guide to the selection of high-voltage cables This Malaysian Standard is identical with IEC 60183:1984 and its Amendment 1:1990. This Malaysian Standard gives guidance in the selection of the conductor size, insulation level and construction of cable to be used on three-phase alternating current systems operation at voltages exceeding 1 kV. Price RM20 MS IEC 60228 : 2001 Conductors of insulated cables Specifies the standardised nominal cross-sectional areas from 0.5 mm2 to 2 000 mm2; as well as numbers and diameters of wires and resistance values for conductors in electric cables and flexible cords. This standard does not apply to conductors for telecommunication purposes, and it applies to conductors of special design only when stated in the specification for the type of cable. Price RM20
MS IEC 60331-21 : 2001 Tests for electric cables under fire conditions - Circuit integrity - Part 21 : Procedures and requirements - Cables of rated voltage up to and including 0.6/1.0 kV This part of MS IEC 60331 specifies the test procedure and gives the performance requirement, including a recommended flame application time, for cables of rated voltage up to and including 0.6/ 1.0 kV required to maintain circuit integrity when subjected to fire under specified conditions. It describes the means of sample preparation, continuity checking arrangements, electrical testing procedure, method of burning the cables and gives requirements for evaluating test results. Price RM20
MS IEC 60229 : 2001 Tests on cable oversheaths which have a special protective function and are applied by extrusion This standard provides a range of standard tests which may be required for protective coverings consisting of extruded oversheaths when the coverings, in addition to protecting underlying metallic layers against corrosion, are required to fulfil special functions. Price RM20
MS IEC 60331-23 : 2001 Tests for electric cables under fire conditions - Circuit integrity - Part 23 : Procedures and requirements - Electric data cables This part of MS IEC 60331 specifies the test procedure and gives the performance requirement, including a recommended flame ap plication time, for electric data cables required to maintain circuit integrity when subjected to fire under specified conditions. It describes the means of sample preparation, continuity checking arrangements, electrical testing procedure, method of burning the cables and gives requirements for evaluating test results Price RM20
MS IEC 60287-1-2 : 2001 Electric cables - Calculation of the current rating - Part 1 : Current rating equations (100 % load factor) and calculation of losses - Section 2 : Sheath eddy current loss factors for two circuits in flat formation This section of IEC 60287-1 provides a method for calculating the eddy current losses in the metallic sheaths of single-core cables arranged as a three-phase double circuit in flat formation. The sheaths are bonded at one point or are cross-bonded so that there are no significant sheath circulating currents. Price RM40
6
MS IEC 60331-25 : 2001 Tests for electric cables under fire conditions - Circuit integrity - Part 25 : Procedures and requirements - Optical fibre cables This part of MS IEC 60331 specifies the test procedure, and gives the performance requirement, including a recommended flame application time, for optical fibre cables required to maintain circuit integrity when subjected to fire under specified conditions. It describes the means of sample preparation, continuity checking arrangements, optical testing procedures, the method of burning the cables and gives requirements for evaluating test results. Price RM20
MS IEC 60811-1-1 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 1: Methods for general application Section 1: Measurement of thickness and overall dimensions Tests for determining the mechanical properties. This Malaysian Standard is a total adoption of IEC 811-1-1 : 1993. This standard specifies the test methods to be used for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships. Price RM40 MS IEC 60811-1-2 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 1: Methods for general application Section 2: Thermal ageing methods. This standard specifies the test methods to be used for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships. This Section Two of Part 1 gives the thermal ageing methods which apply to the most common types of insulating and sheathing compounds (elastometric, PVC, PE, PP etc.) Price RM30
MS IEC 60332-1 : 2001 Tests on electric cables under fire conditions - Part 1 : Test on a single vertical insulated wire or cable Specifies a method of test on a single vertical insulated wire or cable under fire conditions and the requirements for compliance. Price RM20 MS IEC 60332-2 : 2001 Tests on electric cables under fire conditions - Part 2 : Test on a single small vertical insulated copper wire or cable Specifies a method of testing a small insulated wire under fire conditions when the method specified in MS IEC 60332-1 is not suitable because some small conductors may melt during the application of the flame. The range of application recommended is for solid copper conductors from 0.4 mm to 0.8 mm diameter and for stranded conductors from 0.1 mm 2 to 0.5 mm 2 cross-section. This standard includes the requirement for compliance. Price RM20
MS IEC 60811-1-3 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 1: Methods for general application Section 3 : Method for determining the density - Water absorption tests - Shrinkage test This standard specifies the test methods to be used for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships. This Section Three of Part 1 gives the methods for the determining the densi ty, Water absorption tests, Shrinkage test whi ch apply to the most common types of insulating and sheathing compounds (elestometric, PVC, PE, PP etc) Price RM20
MS IEC 60502-1 : 1998 Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um – 1,2 kV) up to 30 kV ((U m – 36 kV) – Part 1 : Cables for rated voltages of 1 kV (U m – 1,2 kV) and 3 kV (Um – 3,6 kV) This Malaysian Standard is identical with IEC 60502-1 : 1997. This standard specifies the construction, dimensions and test requirements for power cables with extruded solid insulation of rated voltages 1 kV and 3 kV for fixed installations such as distribution networks or industrial installations. Cables for special installation and service conditions are not included, for example cables for overhead networks, the mining industry, nuclear power plants (in and around the containment area), submarine use or shipboard application. The standard supersedes MS IEC 502:1996, Extruded solid dielectric insulated power cables for rated voltages from 1 kV up to 30 kV. Price RM60
MS IEC 60811-2-1 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 2: Methods specific to elastometric compounds - Section One : Ozone resistance test-Hot set testMineral oil immersion test. This Malaysian Standard is a total adoption of IEC 811-2-1 : 1986. This standard specifies the test methods to be used for testing polymeric insulating and sheathing material of electric cables for power distribution and telecommunications including cables used on ships. This Section One of Part 2 gives the methods for the ozone resistance test, hot set test and mineral oil immersion test, which apply to elastomeric compounds. Price RM30
MS IEC 60502-2 : 1998 Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um – 1,2 kV) up to 30 kV ((U m – 36 kV) – Part 2 : Cables for rated voltages of 6 kV (U m – 7,2 kV) and 30 kV (U m – 36 kV) This Malaysian Standard is identical with IEC 60502-2 : 1997. This standard specifies the construction, dimensions and test requirements for power cables with extruded solid insulation from 6 kV and 30 kV for fixed installations such as distribution networks or industrial installations. Price RM70 MS IEC 60502-4 : 1998 Power cables with extruded insulation and their accesso ries for rated voltages from 1 kV (U m – 1,2 kV) up to 30 kV ((U m – 36 kV) – Part 4 : Test requirements on accessories for cables with rated voltages from 6 kV (U m – 7,2 kV) and 30 kV ( U m – 36 kV) This Malaysian Standard is identical with IEC 60502-4 : 1997. This standard specifies the test requirements for type testing of accessories for power cables with rated voltages from 6 kV up to 30kV. Accessories for particular cables, such as aerial, submarine or ship cables are not included. The standard supersedes MS IEC 502:1996, Extruded solid dielectric insulated power cables for rated voltages from 1 kV up to 30 kV. Price RM40
7
MS IEC 60811-3-1 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 3: Methods specific to PVC compounds - Section One : Pressure test at high temperature - Tests for resistance to cracking. This Malaysian Standard is a total adoption of IEC 811-3-1 : 1985. This standard specifies the test methods to be used for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships. This Section One of Part 3 gives the methods for pressure test at high temperature and for tests for resistance to cracking, which apply to PVC compounds. This standard includes Amendment 1 : 1994 to IEC 811-3-1 : 1985. Price RM30
MS IEC 60811-3-2 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 3: Methods specific to PVC compounds - Section Two : Loss of mass test - thermal stability test. This standard specifies the test methods to be used for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships. This Section Two of Part 3 gives the methods for loss of mass test and thermal stability test, which apply to PVC compounds. This standard includes Amendment 1 : 1993 to IEC 811-3-2 : 1985. Price RM30
MS IEC 60885-1 : 2003 Electrical test methods for electric cables – Part 1: Electrical tests for cables, cords and wires for voltages up to and 450/750 V This Malaysian Standard is identical with IEC 60885-1:1987. This Malaysian Standard specifies the electrical test methods for testing wires, cords and cables where the relevant cable standard does not prescribe a different electrical test method. The electrical tests are only applicable to: -unsheathed wires, cords and cable s,; -cores taken from complete sheathed cords and cables, all having a maximum rated voltage up to and including 450/750 V. Price RM10
MS IEC 60811-4-1 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 4 : Methods specific to polyethylene and polypropylene compounds - Section One : Resistance to environmental stress cracking - Wrapping test after thermal ageing in air - Measurement of the melt flow index - Carbon black and/or mineral content measurement in PE. This Malaysian Standard is a total adoption of IEC 811-4-1 : 1985. This standard specifies the test methods to be used for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships. This Section One of Part 4 gives the methods for measurement of the resistance to environmental stress cracking, for wrapping test after thermal ageing in air, for measurement of melt flow index and for measurement of carbon black and/or mineral content, which apply to PE and PP compounds, including cellular compounds and foam skin for insulation. This standard includes Amendment 2 : 1993 to IEC 811-4-1 : 1985. Price RM40
MS IEC 60885-2 : 2003 Electrical test methods for electric cables – Part 2 : Partial discharge tests This Malaysian Standard is identical with IEC 60885-2:1987. This Malaysian Standard specifies the test methods for electrical cables. Price RM10 MS IEC 60885-3 : 2003 Electrical test method s for electric cables – Part 3: Test methods for partial discharge measurements on lengths of extruded power cables This Malaysian Standard is identical with IEC 60885-3:1988. This Malaysian Standard specifies the essential requirements for partial discharge measurements on lengths of extruded power cable. Price RM40
29.100.20 Electrical and electromechanical components
MS IEC 60811-4-2 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 5 : Methods specific to polyethylene and polypropylene compounds - Section Two : Elongation at break after pre-conditioning - Wrapping test after thermal ageng in air- Measurement of mass increase - Long - term stability test (Appendix A) - Test method for copper - Catalysed oxidative degradation (Appendix B) This Malaysian Standard is a total adoption of IEC 811-4-2 : 1990. This standard specifies the test methods for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships. This Section Two of Part 4 gives the methods for measurement of elongation at break after pre-conditioning, for wrapping test after preconditioning, for wrapping test after thermal ageing in air, for measurement of mass increase, for long-term stability test and for measurement of copper-catalysed oxidative degradation, which apply to polyolefin insulations. Price RM30
MS 859 : Part 1 : 1991 Specification for electricity meters (electromechanical) : Part 1 : Class 0.5, 1 and 2 single-phase and polyphase, single rate and multi-rate watthour meters (First revision). This standard specifies the mechanical and electrical requirements and type tests, for single-phase and polyphase, single rate and multirate, induction type watthour meters of accuracy classes 0.5, 1 and 2, for the measurement of alternating current electrical active energy of a frequency in the range of 45 Hz to Hz, and having a voltage across the connection terminals not exceeding 600 V (line-to-line for meters for polyphase systems). Price RM40 MS 859 : Part 2 : 1989 Specification for electricity meters : Part 2 : Specification for class 3 var-hour meters. Specifies the mechanical and electrical requirements and type tests for single-phase and polyphase, single rate and multi-rate, var-hour (reactive volt-ampere-hour) meters of accuracy Class 3, for the measurement of alternating current electrical reactive energy of a frequency in the range 45 Hz to 65 Hz and having a voltage across connection terminals not exceeding 600 V (line to line for meters for polyphase systems) Price RM20
MS IEC 60811-5-1 : 1997 Common test methods for insulating and sheathing materials of electric cables. Part 5 : Methods specific to filling compounds - Section One : Drop -point - Separation of oil - lower temperature brittleness - Total acid number- Absence of corrosive components- Permittivity at 23 °C D.C. Resistivity at 23 °C and 100°C. This Malaysian Standard is a total adoption of IEC 811-5-1 : 1990. This standard specifies the test methods for filling compounds of electric cables used with telecommunication equipment. This part includes definitions, requirements and tests, covering all types of RCCB’s. This standard shall supersede MS 1139 : 1989. Price RM30
8
MS 859 : Part 3 : 1996 Specification for electricity meters : Part 3 : Specification for meters having class 1 electro-mechanical maximum demand indicators (First revision). This revised Malaysian Standard specifies the mechanical and electrical requirements and type tests for meters having maximum demand indicators of class 1. This standard shall supersede MS 859 : Part 3 : 1989 Price RM20
29.120
29.120.10
Conduits for electrical purposes
MS 275 : Part 1 : 1975 Specification for steel conduits and fittings with metric threads or ISO form for electrical installations : Part 1 : Steel conduits, bends & couplers (internationally acceptable sizes). Price RM30 MS 275 : Part 2 : 1975 Specification for steel conduits and fittings with metric threads of ISO form for electrical installations : Part 2 : Fittings and components (non-internationally acceptable sizes). Specifies classification, dimensions and tests for conduit fittings and components of sheet or malleable cast iron. In certain cases a wide choice of materials is given and indi cated on relevant standard sheets. Price RM40
Electrical accessories
MS 1144 : 1998 General requirements for electric accessories (First revision). This Malaysian Standard specifies requirements and tests to check the safety in normal use of electrical accessories which are not covered by other specific Malaysian Standards. This standard also covers ‘plug-in’ and other accessories in which electrical accessory component are incorporated, e.g. plug-pins, socket-contacts, switches. terminals, etc. Price: RM70
MS 1034 : 1986 Specification for rigid polyvinyl chloride conduit for underground telecommunication cables. Covers the requirements including materials and test methods to determine heat reversion, tensile, impact strength and resistance to acetone. Price RM20 MS 1534 : Part 1 : 2002 Specification for conduit systems for electrical installations : Part 1 : General requirements This standard specifies requirements and tests for conduit systems, including conduits and conduit fittings, for the protection and management of insulated conductors and/or cables in electrical installations or in communication systems up to 1 000 V a.c. and/or 1 500 V d.c.. This standard supersedes MS 67 : Part 1 : 1972
POPULAR !
Price RM40 MS 1534 : Part 2 : Section 1 : 2002 Specification for conduit systems for electrical installations : Part 2 : Particular requirements : Section 1 : Rigid conduit systems This clause of Part 1 is applicable, except as follows. Addition: This standard specifies the requirements for rigid conduit systems. Conduit systems which are used as an integral part of other equipment also have to be tested according to the relevant standard for that equipment. This standard supersedes MS 67 : Part 1 : 1972. Price RM20 MS 1534 : Part 2 : Section 2 : 2003 Specification for conduit systems for electrical installations: Part 2: Particular requirements: Section 2: Pliable conduit systems This standard specifies requirements and tests for conduit systems, including conduits and conduit fittings, for the protection and management of insulated conductors and/or cables in electrical installations or in communication systems up to 1 000 V a.c. and/or 1 5000 V d.c. This Standard applies to metallic, non-metallic and composite conduit systems including threaded and non-threaded entries which terminate the system.
MS IEC 60335-2-95 : 2003 Household and similar electrical appliances – safety : Part 2-95 : Particular requirements for drives for vertically moving garage doors for residential use. Price RM30 MS IEC 60335-2-97 : 2003 Household and similar electrical appliances-Safety-Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment This Malaysian Standard deals with the safety of electric drives for rolling equipment such as shutters, blinds and awnings, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances.
Price RM20 MS 1534 : Part 2 : Section 3 : 2003 Specification for conduit systems for electrical installations : Part 2 : Particular requirements : Section 3 : Flexible conduit systems. This standard specifies requirements and tests for conduit systems, including conduits and conduit fittings, for the protection and management of insulated conductors and/or cables in electrical installations or in communication systems up to 1 000 V a.c. and/or 1 5000 V d.c. This Standard applies to metallic, non-metallic and
Price RM30
9
composite conduit systems including threaded and non-threaded entries which terminate the system. This Standard does not apply to enclosures and connecting boxes which come within the scope of MS IEC 60670. Price RM20 MS 1534 : Part 2 : Section 4 : 2003 Specification for conduit systems for electrical installations : Part 2 : Particular requirements : Section 4 : Conduit systems buried underground. This standard specifies requirements and tests for conduit systems, including conduits and conduit fittings, for the protection and management of insulated conductors and/or cables in electrical installations or in communication systems up to 1 000 V a.c. and/or 1 5000 V d.c. Price RM20 MS 1777 : Part 1 : 2005 Cable trunking and cable ducting systems for electrical installations – Part 1 : General requirements This Malaysian Standard specifies requirements and tests for cable trunking systems and cable ducting systems intended for the accommodation and where necessary for the segregation of insulated conductors, cables, cords and possibly other electrical equipment in electrical and/or communication systems installation up to 1000 V a.c and /or 1 500 V d.c. Price RM30
MS IEC 60423 : 2002 Conduits for electrical purposes – Outside diameters of conduits for electrical installations and threads for conduits and fittings This Malaysian Standard specifies outside diameters for conduits used in electrical installations and the dimensional requirements for threads used in associated fittings. Price RM30 MS IEC 61537 : 2006 Cable tray systems and cable ladder systems for cable management This Malaysian Standard specifies requirements and tests for cable tray systems and cable ladder systems intended for the support and accommodation of cables and possibly other electrical equipment in electrical and/or communication systems installations. Where necessary, cable tray systems and cable ladder systems may be used for the segregation of cables. This standard does not apply to conduit systems, cable trunking systems and cable ducting systems or any current-carrying parts. Price RM70
29.120.30
Plugs, socket outlets, couplers
MS 589 : Pt. 1 : 1997 Specification for 13A plugs, socket-outlets, adaptors and connection units : Part 1 : Specification for rewirable and nonrewirable 13A plugs (First revision) This Malaysian Standard specifies requiremen ts for 13A fused plugs having insulating sleeves on line and neutral pins, for household, commercial and light industrial purposes, with particular reference to safety in normal use. The plugs are suitable for the connection of portable appliances, sound-vision equipment, luminaires, etc., in a.c. circuits only, operating at voltages not exceeding 250 V r.m.s at 50 Hz. This standard supersedes MS 589 : 1989. Price RM70
MS 1777 : Part 2-3 : 2006 Cable trunking and cable ducting systems for electrical installations - Part 2-3 : Particular requirements for slotted cable trunking intended for installations in cabinets. This Malaysian Standard specifies requirements and tests for slotted cable trunking systems intended for the accommodation and where necessary for the segregation of conductors, cables or cords inside cabinets for electrical and/or communication systems installation up to 1000 V a.c. and/or 1500 V d.c Price RM20 MS 1777 : Part 2-4 : 2006 Cable trunking and ducting systems for electrical installations - Part 2 : Particular requirements : Section 4 : Service poles Replacement : This section of IEC 1084-2 specifies requirements for service poles intended for the accommodation and where necessary for the segregation of conductors, cables and cords and/or other electrical equipment in electrical installations. Price RM20
MS 589 : Pt. 2 : 1997 Specification for 13A plugs, socket-outlets, adaptors and connection units : Part 2 : Specification for 13A switched and unswitched socketoutlet (First revision) This Malaysian Standard specifies requirements for 13A switched and unswitched shuttered socket outlets for household, commercial and light industrial purposes, with particular reference to safety in normal use. Price RM70
MS 1873 : 2005 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 1 : General requirements (First revision) This Malaysian Standard applies to boxes, enclosures and parts of enclosures for electrical accessories with a rated voltage not exceeding 1000 V a.c and 1500 V d.c intended for household or similar fixed electrical installations either indoors or outdoors. Price RM70 MS 1873 : Part 22 : 2006 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 22 : Particular requirements for connecting boxes and enclosures (First revision) This clause of Part 1 is applicable with the following addition : Add after the fourth paragraph. This standard applies to connecting boxes for junction (s) and/or tapping (s). Price RM20
10
Best Sellers
MS 589 : Pt. 3 : 1998 Specification for 13A plugs, socket-outlets, adaptors and connection units : Part 3 : Specification for adaptors. This part of MS 589 specifies for requirements for adaptors having insulating sleeves on the line and neutral plug pins and suitable for use with sockets outlets complying with MS 589:Part 2, with particular reference to safety in normal use. The adaptors are suitable for the connection of potable appliances, sound-vision equipment, luminaires, etc., in a.c. circuits only operating at voltages not exceeding 250 V r.m.s. at 50Hz. Price RM90 MS 589 : Pt. 4 : 1998 Specification for 13A plugs, socket-outlets, adaptors and connection units : Part 4 : Specification for 13A fused connection units : Switched and unswitched This standard specifies requirements for 13A fused fixed connection units for household, commercial and light industrial purposes, with particular reference to safety in normal use. The connection units are suitable for the connection of appliances in a.c. circuits only, operating at voltages not exceeding 250 V r.m.s at 50 Hz. Price RM40
29.120.40
Switches
MS 1141 : 2006 Portable cable reels for domestic and similar purposes – Specification (First revision) This Malaysian Standard specifies requirement which applies to portable cable reels for alternating current (a.c) only, having a rated voltage not exceeding 25o V, rated current not exceeding 13 A and provided with a non-detachable flexible cable or cord intended for domestic and similar purposes, either indoor or outdoor. Price RM50 MS 1039 : 1986 Specification for alternating current switches of rated voltage above one kilovolt Price RM80
MS 1578 : 2003 Specification for flat non-rewirable two-pole plugs, 2.5 A, 250 V, with cord, for the connection of Class II – Equipment for household and similar purposes. This Malaysian Standard applies to flat non-rewirable two-pole plugs without earthing contact with a rated voltage of 250 V a.c. and a rated current of 2.5 A. They are supplied with a cord, for the connection of equipment of class II, for household and similar purposes, and having no special protection against ingress of water and intended for indoor use. Price RM30
MS 1577 : 2003 Specification for 15 A plugs and socket-outlets for domestic and similar purposes This Malaysian Standard specifies the requirements for 15 A rewirable plugs and switched or unswitched socket-outlets for use on a nominal supply voltage not exceeding 250 V a.c. single-phase 50 Hz. For switched socket-outlets which contain a switch connected between the current carrying contact(s) of the socket-outlets and the relevant supply terminal(s). In general, the provisions of this standard shall apply to plugs when wired with appropriate flexible cords or cables, and to socket-outlets installed. Price RM30
MS 1579 : 2003 Specification for portable 2 pin socket-outlets for Class II equipment for household and similar purposes. This Malaysian Standard applies to portable 2 pin socket-outlets for a.c. only, without earthing contacts, with a rated voltage of 250 V and a rated current not exceeding 13 A, intended for household and similar purposes. Price RM50
MS IEC 60320-1 : 2003 Appliance couplers for household and similar general purposes – Part 1: General requirements This part of MS IEC 60320 is applicable to two-pole appliance couplers for a.c. only, with or without earthing contact, with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A, for household and similar general purposes and intended for the connection of a supply cord to electrical appliances or other electrical equipment for 50 Hz or 60 Hz supply. Price RM130
MS IEC 60669-1 : 2004 Switches for household and similar fixed electrical installation – Part 1 : General requirements This part of IEC 60669 applies to manually operated general purpose switched, for a.c. only with a rated voltage not exceeding 440 V and a rated current not exceeding 63 A, intended for household and similar fixed-electrical installations, either indoors or outdoors. Price RM100
MS IEC 60669-2-1 : 2004 Switches for household and similar fixed electrical installations – Part 2-1: Particular requirements – Electronics switches MS IEC 60320-2-2 : 2003 This standard applied to electronic switches and associated Appliance couplers for household and similar general electronic extension units for household and similar fixed electrical purposes – Part 2-2: Interconnection couplers for installations either indoors or outdoors. household and similar Price RM50 This clause of MS IEC 60320-1 is replaced as follows. This standard MS IEC 60669-2-2 : 2004 is applicable to two-pole interconnection couplers for a.c. only, Switches for household and similar fixed electrical installation – with and without earthing contact, with a rated voltage not exceeding Part 2-2: Particular requirements – Remote control switches (RCS) 250 V and a rated current not exceeding 16 A, for household and This standard applies to remote-control switches (hereinafter similar appliances and equipment and intended for the interconnection of the electrical supply to electrical appliances or referred to as RCS). This standard applies to electromagnetic RCS with a rated voltage exceeding 440V and a rated current not equipment for 50 Hz or 60 Hz supply. exceeding 63 A, and to electronic RCS with a rated voltage not Price RM50 exceeding 250V and a rated current not exceeding 16A, intended for household and similar fixed electrical installations, either indoors or outdoors. Price RM30
11
MS IEC 60669-2-3 : 2004 Switches for household and similar fixed electrical installations – Part 2-3: Particular requirements – Time-delay switches (TDS) This standard applies to time-delay switches (hereinafter referred to as TDS) with a rated voltage not exceeding 440 V and a rated current not exceeding 63 A, intended for household and similar fixed electrical installations, either indoors or outdoors, operated by hand and/or by remote control and which are provided with a mechanical, thermal, pneumatic, hydraulic or electrical operated time-delay device or with combines any of them. Price RM30 MS IEC 60947-3 : 2006 Low - voltage switchgear and controlgear – Part 3 : Switches, disconnectors, switch-disconnectors and fuse combination units This Malaysian Standard applies to switches, disconnectors, switchdisconnectors and fuse-combination units to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1000 V a.c or 1500 V d.c Price RM60 MS IEC 60947-5-1 : 2005 Low voltage switchgear and controlgear – Part 5-1 : Control circuits devices and switching elements – Electromechanical control circuit devices This Malaysian Standard applies to control circuit devices and switching elements intended for controlling, signaling, interlocking, etc. of switchgear and controlgear. It applies to control circuit devices having a rated voltage not exceeding 1000 V a.c (at a frequency not exceeding 1000 Hz) or 600 V d.c Price RM100 MS IEC 60947-5-2 : 2005 Low-voltage switchgear and controlgear – Part 5-2 : Control circuit devices and switching elements – Proximity switches This Malaysian Standard applies to inductive and capacitive proximity switches that sense the presence of metallic and/or non-metallic objects, ultrasonic proximity switches that sense the presence of sound reflecting objects, photoelectric proximity switches that sense the presence of objects and non-mechanical magnetic proximity switches that sense the presence of objects with a magnetic field. Price RM110
29.120.50
Fuses and other overcurrent protection devices
MS 1428 : 1997 Specification for general purpose fuse links for domestic and similar purposes (primarily for use in plugs). This Malaysian Standard specifies dimensions and performance requirements for general purpose cartridge fuse links of current ratings not exceeding 13A for domestic and similar purposes. Price RM30
MS IEC 60269-1 : 2003 Low-voltage fuses – Part 1: General requirements This Malaysian Standard is applicable to fuses incorporating enclosed current-limiting use fuse links with related breaking capacities of not less than 6 kA, intended for protecting power-frequency a. c. circuits of nominal voltages not exceeding 1 000 V or d. c. circuits or normal voltages not exceeding 1 500 V. Price RM80 MS IEC 60269-2 : 2005 Low voltage fuses – Part 2 : Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application. This Malaysian Standard apply to fuses for use by authorized persons. Fuses for use by authorized persons are generally designed to be used in installations where the fuse-link are accessible to and may be replaced by authorize persons only. Price RM20 MS IEC 60269-2-1 : 2003 Low voltage fuses-Part 2-1: Supplementary requirements for use by authorized person (Fuses mainly for industrial application)Section I to IV: Examples of types of standardized fuses T he following additional requirements apply to fuses with fuse-links having blade contacts intended to be replaced by means of a device, for example replacement handle, which complies with the dimensions specified in figures 1(I*) and 2(I*).Such fuses have rated currents up to and including 1250A and rated voltages up to and including AC 690 V or DC 440V. Price RM140 MS IEC 60269-3-1 : 2003 Low-voltage fuses – Part 3-1: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) Sections I to IV This Malaysian Standard is divided into four sections, each dealing with a specific example of standardised fuses. Price RM130 MS IEC 60269-4 : 2003 Low-voltage fuses - Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices These supplementary requirements appl y to fuse-links for application in equipment containing semiconductor devices for circuits of rated voltages up to 1000 V a.c. or circuits of nominal voltages up to 1500 V d.c. and also, in so far as they are applicable, for circuits of higher nominal voltages. Price RM90 MS IEC 60269-4-1 : 2005 Low-voltage fuses – Part 4-1 : Supplementary requirements for fuse-links for the protection of semicondu ctor devices – Section I to III : Examples of types of standardized fuse-links Price RM30
MS 1586 : Part 3 : 2003 Low-voltage fuses - Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) This Malaysian Standard applies to “gG” fuses for use by unskilled persons for domestic and similar applications with rated currents not exceeding 100 A and rated voltages not exceeding 500 V a. c. Additional specific requirements are given in IEC Publication 269-3-1. Price RM20
12
MS IEC 60898-1 : 2006 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations - Part 1: Circuit-breakers for a.c. operation. This part of MS IEC 60898 applies to a.c. air-break circuit-breakers for operation at 50 Hz or 60 Hz, having a rated not exceeding 440 V (between phases), a rated current not exceeding 125 A and a rated short-circuit capacity not exceeding 25 000 A. Price RM150
MS IEC 60898-2 : 2006 Circuit-breakers for overcurrent protection for household and similar installations - Part 2: Circuit-breakers for a.c. and d .c. operation (First revision) This clause of Part 1 is applicable except as follows ; Addition at the end of the first paragraph. This standard gives additional requirements for single- and two-pole circuit-breakers which in addition to the above characteristics are suitable for operation with direct current and have a rated d.c voltage not exceeding 220 V for single-pole and 440 V for two-pole circuit-breakers, a rated current not exceeding 125 A and a rated d.c short-circuit capacity not exceeding 10000 A. Price RM30
MS IEC 61009-1 : 2003 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) This Malaysian Standards applies to residual current operated circuitbreakers with integral overcurrent protection functionally independent of, or dependent on, line voltage for household and similar uses, for rated voltages not exceeding 440 V a.c., rated current not exceeding 125 A and rated short-circuit capacities not exceeding 25000 A for operation at 50 Hz or 60 Hz. Price RM150
MS IEC 60947-2 : 2000 Low-voltage switchgear and controlgear - Part 2 : Circuitbreakers Applies to circuit-breakers, the main contacts of which are intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c.; it also contains additional requirements for integrally fused circuit-breakers. Price RM140
MS IEC 61009-2-1 : 2003 Residual current operated circuit-breakers with integral overcurrent protection for household and similar This Malaysian Standards applies to residual current operated circuitbreakers with integral overcurrent protection (RCBO’s) functionally independent of line voltage, for household and similar uses incorporating overcurrent protection having rated voltages not exceeding 440 V a.c., rated currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A, for operation at 50 Hz or 60 Hz. Price RM20
MS IEC 60947-3 : 2000 Low-voltage switchgear and controlgear - Part 3 : Switches, disconnectors, switch-disconnectors and fuse-combination units Applies to switches, disconnectors, switch-disconnectors and fusecombination units to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1 000 V a.c. or 1 500 V. d.c. This standard is identical with IEC 60947-3 : 1999. Price RM60
MS IEC 61009-2-2 : 2003 Residual current operated circuit-Breakers with integral overcurrent protection for household and similar uses (RCBO’s). Part 2-2: Applicability of the general rules to RCBO’s functionally dependent on line voltage This part of MS IEC 61009 supplements or modifies the corresponding clauses in IEC 1009-1 to cover its applicabili ty to RCBO’s functionally dependent on line voltage. Price RM20
MS IEC 61008-1 : 2006 Residul current operated circuit-breakers without integral overcurrent protection for hou sehold and similar uses (RCCBs) – Part 1: General rules (First revision) This Malaysian Standard applies to residual current operated circuitbreakers functionally independent of, or functionally dependent on, line voltage, for household and similar uses, not incorporating overcurrent protection (hereafter referred to as RCCBs), for rated voltages not exceeding 440 V a.c. and rated currents not exceeding 125 A, intended principally for protection against shock-hazard. Price RM140 MS IEC 61008-2-1 : 2003 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) – Part 2-1: Applicability of the g eneral rules to RCCB’s functionally independent of line voltage. This Part 2-1 supplements or modifies the corresponding clauses in MS IEC 61008-1 to cover its applicability to RCCB’s functionally independent of line voltage. Price RM10
29.120.99
Other electrical accessories
MS 1873 : Part 21 : 2006 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 21 : Particular requirements for boxes and enclosures with provision for suspension means (First revision) This clause of Part 1 is applicable with the following modification : Addition after the fourth paragraph. This standard applies to boxes and enclosures with provision for suspension means. Price RM20
29.130
Switchgear and controlgear
MS 1445 : Pt. 1 : 1998 Low voltage switchgear and controlgear asemblies Part 1 : Typetested and partially type-tested assemblies. This Malaysian Standard applies to low-voltage switchgear and controlgear assemblies (type-tested assemblies (TTA) and partially type-tested assemblies (PTTA), the rated voltage of which does not exceed 1000 V a.c. at frequencies not exceeding 1000 Hz, or 1500 V d.c. Price RM110
MS IEC 61008-2-2 : 2003 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) – Part 2-2: Applicability of the g eneral rules to RCCB’s functionally dependent on line voltage. This Part 2-2 supplements or modifies the corresponding clauses in MS IEC 61008-1 to cover its applicability to RCCB’s functionally dependent on line voltage. This clause of part 1 is applicable. Price RM10
MS 1445 : Pt. 3 : 1998 Low voltage switchgear and controlgear asemblies Part 3 : Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their – Distribution boards This Malaysian Standard gives requirements for enclosed distribution boards (DBU), which are stationary, type-tested assemblies
13
(TTA) for indoor use, containing protective devices and intended for use either in domestic (household) applications or in other places where unskilled persons have access for their use. Control and/or signalling devices may also be included. They are for use on a.c., with a nominal voltage to earth not exceeding 300 V. The outgoing circuits contain short-circuit protective devices, each having a rated current not exceeding 125 A with a total incoming load current not exceeding 250 A. Price RM100
This Malaysian Standard applies to busbar trunking systems (BTS) and their accessories for feeding and distributing electrical power in residential, retail, public, agriculture and industrial premises. Price RM40 MS IEC 60439-3 : 2003 Low-voltage switchgear and controlgear assemblies - Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use-Distribution boards. Price RM30
29.130.10 High voltage switchgear and controlgear
MS 1781 : 2005 Common specifications for high-voltage switchgear and controlgear standards. This Malaysian Standard applies to a.c switchgear and controlgear, designed for indoor and outdoor installations and for operation at service frequencies up to and including 60 Hz on systems having voltages above 10000 V. Price RM 120 MS 1782 : 2005 High-voltage switchgear and controlgear – AC metal-enclosed switchgear and controlgear rated voltages above 1 kV and up to and including 52 kV. This Malaysian Standard specifies requirements for factoryassembled metal-enclosed switchgear and controlgear for alternating current of rated voltages above 1 kV and up to and including 52 kV for indoor and outdoor installation and for services frequencies up to and including 60Hz. Enclosures may include fixed and removable components and may be filled with fluid (liquid or gas) to provide insulation. Price RM90 MS 1840 : 2005 High-voltage switchgear and controlgear – Part 100 : Highvoltage alternating-current circuit-breakers This Malaysian Standard is applicable to a.c circuit-breakers designed for indoor or outdoor installation and for operation at frequencies of 50 Hz and 60 Hz on systems having voltages above 1000 V. Price RM300
29.130.20 Low voltage switchgear and controlgear MS 948 : 1984 Specification for factory-built assemblies of switchgear and controlgear. Applies to low voltage switchgear and controlgear where rated voltage does not exceed 100V a.c. and at frequencies no t exceeding 1000Hz, or 1200V d.c. Price RM60 MS IEC 60439-1 : 2005 Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies. This Malaysian Standard applies to low-voltage switchgear and controlgear assemblies (type-tested assemblies (TTA) and partially type-tested assemblies (PTTA)). Price RM110 MS IEC 60439-2 : 2002 Low-voltage switchgear and controlgear assemblies - Part 2: Particular requirements for busbar trunking systems (busways).
MS IEC 60439-4 : 2005 Low-voltage switchgear and controlgear assemblies – Part 4 : Particular requirements for assemblies for construction sites (ACS) This Malaysian Standard applies to type-tested assemblies (TTA) intended for use on construction sites. These assemblies may be transportable (semi-fixed) or mobile. Price RM30 MS IEC 60439-5 : 2004 Low-voltage switchgear and controlgear assemblies – Part 5 : Particular requirements for assemblies – Part 5: Particular requirements for assemblies intended to be installed outdoors in public places – Cables distribution cab inets (CDCs) for power distribution in networks This standard gives supplementary requirements for cable distribution cabinets (CDCs). Price RM40 POPULAR !
MS IEC 60947-1 : 2004 Low-voltage switchgear and controlgear – Part 1 : General rules This standard applies, when required by the relevant product standard, to switchgear and controlgear hereinafter referred to as “equipment” and intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c. or 1 5000 V d.c. Price RM180 MS IEC 60947-3 : 2006 Low - voltage switchgear and controlgear – Part 3 : Switches, disconnectors, switch-disconnectors and fuse combination units This Malaysian Standard applies to switches, disconnectors, switchdisconnectors and fuse-combination units o be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1000 V a.c or 1500 V d.c Price RM60 MS IEC 60947-4-1 : 2005 Low-voltage switchgear and controlgear : Part 4-1 Contactors and motor-starters – Electromechanical contactors and motorstarters (First revision) This Malaysian Standard applies to the types of equipment listed in sub-clauses 1.1 and 1.2 whose main contacts are intended to be connected to circuits the rated voltage of which does not exceed 1000 V a.c or 1500 V d.c. Price RM100 MS IEC 60947-4-2 : 2005 Low-voltage switchgear and contr olgear – Part 4-2 : Contactors and motor-starters – AC semiconductor motor controllers and starters This Malaysian Standard applies to controllers and starters which may include a series mechanical switching device, intended to be connected to circuits, the rated voltage of which does not exceed 1000 V a.c. Price RM90
14
MS IEC 60947-5-1 : 2005 Low voltage switchgear and controlgear – Part 5-1 : Control circuits devices and switching elements – Electromechanical control circuit devices This Malaysian Standard applies to control circuit devices and switching elements intended for controlling, signaling, interlocking, etc. of switchgear and controlgear. It applies to control circuit devices having a rated voltage not exceeding 1000 V a.c (at a frequency not exceeding 1000 Hz) or 600 V d.c Price RM100 MS IEC 60947-5-2 : 2005 Low-voltage switchgear and controlgear – Part 5-2 : Control circuit devices and switching elements – Proximity switches This Malaysian Standard applies to inductive and capacitive proximity switches that sense the presence of metallic and/or non-metallic objects, ultrasonic proximity switches that sense the presence of sound reflecting objects, photoelectric proximity switches that sense the presence of objects and non-mechanical magnetic proximity switches that sense the presence of objects with a magnetic field. Price RM110 MS IEC 60662 : 2002 High-pressure sodium vapour lamps - Section One : General This Malaysian Standard specifies the characteristics of high-pressure sodium vapour lamps necessary to ensure interchangeability and safety together with test conditions and procedures. The recommendations relate only to type testing. The standard specifies the lamp dimensions, electrical characteristics for lamp starting and operation together with information for ballast, ignitor and luminaire design purpose
This Malaysian Standard specifies general and safety requirements for electronic ballasts for use on a.c supplies up to 1000V at 50Hz or 60Hz with operating frequencies deviati ng from the supply frequency, associated with tubular fluorescent lamps as specified in IEC Publication 81 and other tubular fluorescent lamps for high-frequen cy operation. Price RM40 MS IEC 60929 : 1995 Specification for a.c supplied electronic ballasts for tubular fluorescent lamps-performance requirements. This Malaysian Standard specifies performance requirements for electronic ballasts for use on a.c supplies up to 1000V at 50Hz or 60Hz with operating frequencies deviati ng from the supply frequency, associated with tubular fluorescent lamps as specified in IEC 81 and 901 and other tubular fluorescent lamps for high-frequency operation. Price RM60 MS IEC 60983 : 2002 Miniatures lamps : Section 1 : General This Malaysian Standard specifies requirements for miniature halogen and non-halogen lamps with a nominal voltage up to 30 V and a nominal wattage up to 25 W. It covers: - lamps to be used in road vehicles not subject to regulation and whi ch therefore are not included in IEC 809 (section 2); - lamps for electric torches (section 3); - lamps for miners caplights (section 4). Aircraft lamps are standardized in IEC 434. This standard specifies dimensional, electrical and photometric requirements as well as requirements concerning life and mechanical strength. Price RM60
Price RM140
29.140.01 29.140
Lamps in general
Lamps and related equipment
MS IEC 60922 : 1995 Specification for ballasts for discharge lamps (excluding tubular fluorescent lamps). This Malaysian Standard specifies safety requirements for ballasts for discharge lamps such as high-pressure mercury vapour, lowpressure sodium vapour, high-pressure sodium vapour and metal halide lamps. Section one specifies general requirements and section two specifies thermal and mechanical requirements. The standard covers inductive-type ballasts for use on a.c supplies up to 1000 V at 50Hz or 60Hz associated with discharge lamps, having rated wattages, dimensions and characteristics as specified in the relevant IEC lamp standards according to IEC Publications 188, 192 and 662. Price RM70 MS IEC 60923 : 1995 Specification for performance requirements for ballasts for discharge lamps (excluding tubular fluorescent lamps). This Malaysian Standard specifies performance requirements for ballasts for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. Each section details specific requirements for a particular type of ballast. The standard covers inductive type ballasts for use on a.c supplies up to 1000V at 50Hz or 60Hz associated with discharge lamps, having rated wattage, dimensions and characteristics as specified in the relevant IEC lamp standards. Price RM40
MS 619 : Part 2-22 : 2005 Luminaires – Part 2-22 : Particular requirements – Luminaires for emergency lighting (First revision) This Malaysian Standard specifies requirements for emergency lighting luminaries for use with electrical light sources on emergency power supplies not exceeding 1000 V. Price RM30 MS IEC 60399 : 2003 Standard sheets for barrel thread E14 and E27 lampholders with shade holder ring This Malaysian Standard is identical with IEC 60399:2002. This Malaysian Standard dives the limit dimensions of thread for metal or plastics and ceramic lamp holders with shade holder rings made of metal or plastics. Price RM20 MS IEC 60598-2-9 : 2001 Luminaires : Part 2 : Particular requirements - Section 9 - Photo and film luminaires (non-professional) This section of Part 2 of MS IEC Publication 60598 specifies requirements for photo and film luminaires (non-professional) for use with tungsten filament lamps on supply voltages not exceedi ng 250 V. Price RM30
MS IEC 60928 : 1995 Specification for a.c supplied electronic ballasts for tubular fluorescent lamps-general and safety requirements.
15
MS IEC 60809 : 2001 Filament lamps for road vehicles - Dimensional, electrical and luminous requirements : Section 1 : General This Malaysian Standard covers filament lamps to be used in headlamps, fog-lamps and signalling lamps for road vehicles and specifies the technical requirements with methods of test and basic interchangeability (dimensional, electrical and luminous). It applies to those filament lamps which may be the subject of legislation. Price RM140
MS IEC 61228 : 2003 Method of measuring and specifying the UV-radiation of ultraviolet lamps used for sun-tanning This Malaysian Standard is identical with IEC 61228:1993 and its Amendment 1:1996. This Malaysian Standard specifies a method of measuring, evaluating and specifying the ultraviolet radia tion of lamps which are used in skin treatment appliance s for household and similar use, mainly for sun-tanning purposes. Price RM20
MS IEC 60810 : 2001 Lamps for road vehicles - Performance requirements : Section 1 : General This standard is one of a series of IEC standards for filament lamps to be used in head-lamps, fog-lamps and signaling lamps of road vehicles. It specifies performance requirements and test methods for the measurement of performance characteristics such as life, lumen maintenance, torsion strength, glass bulb strength and vibration resistance; moreover, information on temperature limits, maximum filament lamp outlines and maximum tolerable voltage surges is given for the guidance for lighting and electrical equipment design. Price RM40
29.140.10
MS 769 : 1982 Specification for bayonet lamp-caps lampholders and B.C adaptors (lampholder plugs). Definitions, dimensional and performance requirements and test methods provided. Parts intended use on a nominal voltage nor exceeding 250V. Price RM50
MS IEC 60926 : 2001 Auxiliaries for lamps - Starting devices (Other than glow starters) - General and safety requirements - Section 1 : General This standard specifies general and safety requirements for starting devices (starters and ignitors) for tubular fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 100 kV and which are used in combination with lamps and ballasts covered in IEC 60081, IEC 60188, IEC 60192, IEC 60662, IEC 60920 and IEC 60922. Price RM50
Lamp caps and holders
MS IEC 60061-4 : 2005 Lamp caps and holders together with gauges for the control of interchangeability and safety – Part 4 : Guidelines and general information This Malaysian Standard describes the IEC policy concerning the standardization of cap/holder fits. It gives guidelines for the justification to standardize new fits. Price RM50 MS IEC 60155 : 1996 Glow-starters for fluorescent lamps. This Malaysian Standard specifies interchangeable glow-starters used with preheat type fluorescent lamps. Hereafter called “starters”. Section 1 specifies the general and safety requirements with which starters shall comply; - Section 2 specifies the performance with Amendment. Price RM40
MS IEC 61046 : 2001 D.C. or A.C. supplied electronic step-down convertors for filament lamps - General and safety requirements - Section 1 : MS IEC 60238 : 1999 General requirements Edison screw lampholders This Malaysian Standard specifies general and safety requirements Applies to lampholders with Edison thread E14, E27 and E20, for electronic step-down convertors for use on d.c. supplies up to designed for connection to the supply of lamps and semi-luminaires 250 V or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and rated only. Also applies to swi tched-lampholders for use in a.c. circuits onl y, output voltage < 50 V r.m.s. at a frequency deviating from the supply where the working voltage does not exceed 250 V r.m.s. and to frequency or < 50 √ 2 V unsmoothed d.c. between conductors or lampholders with Edison thread E5 designed for connection to the between any conductor and earth, associated with tungsten-halogen supply mains of series connected lamps, with a working voltage not lamps as specified in IEC 60357 and other filament lamps. exceeding 25 V, to be used indoors, and to lampholders with Edison thread E10 designed for connection to the supply mains of series Price RM70 connected lamps, with a working voltage not exceeding 60 V, to be used indoors or outdoors. It also applies to lampholders E10 for MS IEC 61047 : 2001 building-in, for the connection of single lamps to the supply. D.C. or A.C. supplied electronic step-down convertors for Price RM100 filament lamps - Performance requirements This Malaysian Standard specifies performance requirements for MS IEC 60360 : 2006 electronic step-down convertors for use on d.c. supplies up to 250 V Standard method of measurement of lamp cap temperature rise and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating (First revision) frequencies deviating from the supply frequency, associated with This Malaysian Standard describes the standard method of tungsten halogen lamps as specified in IEC 357 and other filament measurement of lamp cap temperature rise which is to be used when lamps. testing incandescent or discharge lamps for compliance with the Price RM40 MS IEC 61126 : 2001 Procedure for use in the preparation of maximum lamp outlines - Section 1 : General This Malaysian Standard deals with the maximum lamp outline drawings and with the procedure to establish and apply them. It details step-by-step procedures which can be used to produce consistent, accurate but simplified drawings which can be called “maximum lamp outlines”. Price RM70
limits. Temperature-rise limits for particular lamp types are, for example, listed in IEC 60432. It also covers the method of test and the specifications for test lampholders for lamps fitted with various sizes of ES and BC caps. This method has been used widely for incandescent lamps but its application is not limited to that kind of lamp. Price RM20
16
MS IEC 60838-1 : 1999 Miscellaneous lampholders : Part 1 : General requirements and tests Applies to lampholders of miscellaneous types intended for buildingin (To be used with general purpose lamps, projection lamps, floodlighting lamps and street-lighting lamps with caps as listed in Annex A0 and the methods of test to be used in determining the safe use of lamps in lampholders. Requirements for lampholders for tubular fluorescent lamps, Edison screw lampholders and bayonet lampholders are covered by separate standards. This standard is identical with IEC 60838-1 : 1997. Price RM40 MS IEC 60838-2-1 : 1999 Miscellaneous lampholders - Part 2 : Particular requirements Section 1 : Lampholders S14 Applies to lampholders S14 intended for building-in as well as for independent lampholders for use with linear incandescent lamps for general lighting service (GLS). Independent lampholders are also tested as luminaires. This standard is identical with IEC 60838-2-1 : 1994. Price RM20 MS IEC 60400 : 1999 Lampholders for tubular fluorescent lamps and starterholders States the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders. This standard is identical with IEC 60400 : 1991 and its Amendment 1 : 1997. Price RM90 MS IEC 61049 : 1999 Capacitors for use in tubular fluorescent and other discharge lamp circuits performance requirements States the requirements for both self-healing and non-self-healing continuous rated a.c. capacitors of up to and including 2.5 kvar, and not less than 0.1 µF, having a rated voltage not exceeding 1,000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3,000 m. It also covers capacitors intended for connection in shunt or in series with the lamp circuit or an effective combination of these and only those impregnated or unimpregnated capacitors, having a dielectric of paper, plastic film or a combination of both, either metallized or with metal foil electrodes. This standard is identical with IEC 61049 : 1991. Price RM20 MS IEC 61167 : 1999 Metal halide lamps Specifies the methods of test to be used for determining the characteristics of metal halide lamps, both single-ended and doubleended, operated on a.c. mains, 50 Hz or 60 Hz, with ballasts satisfying the requirements of IEC 923. These requirements relate only to type testing. The standard also specifies lamp dimensions, electrical characteristics for lamp starting and operation together with information for ballast, ignitor and luminaire design and colour characteristics. This standard is identical with IEC 61167 : 1992 and its Amendment 3 : 1998. Price RM50
29.140.20
Incandescent lamps
MS ISO 6570 : 2003 Electrical supply track systems for luminaires This Malaysian standard applies to stack systems with two or more poles for the connection of luminaires to the electrical supply, either of rated voltage not exceeding 440 V between poles with provision for earthing (class I) and a rated current not exceeding 16 A per conductor, or of a rated SELV not exceeding 25 V without provision for earthing (class III) and rated current not exceeding 25 A per conductor. The track systems may also provide for the mechanical support of the luminaires. It applies to track systems designed for ordinary interior use for mounting on, or flush with, or suspended from walls and ceilings. These track systems are not intended for locations where special conditions prevail as in ships, vehicles and the like and in hazardous locations, for example, where explosions are liable to occur. This standard shall be read in conjunction with the sections of IEC 60598-1 to which reference is made. Price RM30 MS IEC 60064 : 2006 Tungsten filament lamps for domestic and similar general lighting purposes - Performance requirements (First revision) This standard applies to tungsten filament incandescent lamps for general lighting service (GLS) which comply with the safety requirements in IEC 60432-1 and having:- rated wattage of 25 W to 200 W, inclusive; - rated voltage 100 V 250 V, including marked voltage range not exceeding ± 2.5 % of the mean voltage 1); - bulbs of the A or PS shapes; - bulbs with clear, frosted or equivalently coated finishes, or white finishes; - caps B22d, E26 or E27. Specific lamp types are covered in section 8. This standard also states the performance requirements for lamps, including test methods and means of confirming compliance with the requirements. Price RM100 MS IEC 60357 : 2003 Tungsten halogen lamps (non-vehicle) This Malaysian Standard specifies dimensions and characteristics of tungsten halogen lamps. The standard has been divided into sections according to the following lamp applications: PROJECTION, PHOTOGRAPHIC (including studio), FLOODLIGHTING, SPECIAL PURPOSE, GENERAL PURPOSE, STAGE LIGHTING. Lamps for automobile, aircraft and similar applications are not covered by this standard. Price RM110 MS IEC 60432-1 : 2006 Incandescent lamps - Safety specifications : Part 1 : Tungsten filament lamps for domestic and similar general lighting purposes (First revision) This Malaysian Standard specifies the safety and interchangeability requirements of tungsten filament incandescent lamps for general lighting service, having a rated wattage up to and including 200W and a rated voltage from 50V to 250V inclusive – bulbs of the A, B,C, G, M, P, PS, PAR or R shapes or other bulb s hapes where the lamps are intended to serve the same purpose as lamps with the foregoing bulb shapes; bulbs with all kinds of finishes; caps B15d, B22d, E12, E14, E17, E26d, E26/50x39, E27 or E27/51x39. Price RM50 MS IEC 60432-2 : 2006 Incandescent lamps - Safety specifications : Part 2 : Tungsten halogen lamps for domestic and similar general lighting purposes (First revision) This Malaysian Standard specifies the safety and the related interchangeability requirements of tungsten halogen lamps for general lighting service. It covers those tungsten halogen lamps that are
17
used as direct replacements for conventional tungsten filament l amps as well as new tungsten halogen lamps which have no correspondence in MS IEC 60432-1, but for which the safety and interchangeability requirements are treated by this standard in conjunction with MS IEC 60432-1. Price RM20
MS 279 : 1983 Specification for capacitors for use in tubular fluorescent, highpressure mercury and low-pressure sodium vapour discharge lamp circuits (First revision). Specifies requirements for both self-heating and non-self-heating capacitors of up to and including 2.5 Kvar. with capacitance of not less than 0.1 F and having rated voltage not exceeding 1Kv. Price RM30
MS IEC 60432-3 : 2006 Incandescent lamps - Safety specifications : Part 3 : Tungsten halogen lamps (Non-vehicle) This Malaysian Standard specifies the safety for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V used for the following applications, Projection (Including cinematograph and still projection), photographic (including studio), floodlighting, special purpose, general purpose and stage lighting. Price RM40
MS 1778 : Part 1 : 2005 Electrical lighting equipment – Ballast for fluorescence lamps – Part 1 : Measurement of energy consumption and performances of ballast – lamp circuit. This Malaysian Standard specifies methods of measurement of ballast energy consumption and performance when used with their associated fluorescent lamps(s). Price RM30
MS IEC 60570 : 2006 Electrical supply track systems for luminaries (First revision) This Malaysian Standard applies to the following track systems with two or more poles for the connection of luminaries to the electrical supply. Price RM30
MS 1778 : Part 2 : 2005 Electrical lighting equipment – Ballast for fluorescence lamps – Part 2 : Energy labelling and minimum energy performance standard requirements. This Malaysian Standard specifies the requirements for the classification of ballasts for a range of fluorescence lamp types according to their Energy Efficiency Index (EEI) and the form of labelling of the EEI, which is generally shown on the ballast rating plate. Price RM20
MS IEC 60630 : 2003 Maximum lamp outlines for incandescent lamps This Malaysian Standard is identical wit IEC 60630:2001. This Malaysian Standard specifies requirements for maximum lamp outlines for incandescent lamps (including tungsten-halogen lamps). Price RM100
MS IEC 60081 : 2003 Double-capped fluorescent lamps - Performance specifications (First revision) This Malaysian Standard covers a range of tubular fluorescent lamps for the general lighting service which are operated on a.c mains. Lamps of the following types are included : - a) Lamps with preheated cathodes operated with the use of the +starter; b) Lamps with preheated cathodes oper ated without the use of the starter; c) Lamps wih preheated cathodes operated with or without the use of starter; d) Lamps with non-preheated cathodes operated without used of the starter. Price RM100
MS IEC 61549 : 2003 Miscellaneous lamps This Malaysian Standard specifies lamps or information relevant to lamps not covered elsewhere in the scope of existing IEC standards. Price RM30
29.140.30
Fluorescent lamps. Discharge lamps
MS 141 : Part 1 : 1993 Specification for ballasts for tubular fluorescent lamps : Part 1 : General and safety requirements (First revision). This Malaysian Standard specifies general and safety requirements for ballasts excluding resistance types for use on a.c. supplies up to 1000 V at 50 Hz, associated with tubular fluorescent lamps with preheated cathodes operated with or without a starter or starting device and having rated wattage, dimensions and characteristics as specified in IEC Publications 81 and 901. Price RM50
MS IEC 60188 : 2006 High-pressure mercury vapour lamps – Performance specifications (First revision) This standard specifies the performance requirements for highpressure mercury vapour lamps for general lighting purposes, with or without a red correcting fluorescent coating operating. Price RM40
MS 141 : Part 2 : 1993 Specification for ballasts for tubular fluorescent lamps : Part 2 : Performance requirements This Malaysian Standard specifies performance requirements for ballasts excluding resistance types for use on a.c. supplies up to 1000 V at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in IEC Publications 81 and 901. Price RM30
MS IEC 60927 : 2003 Auxiliaries for lamps – Starting devices (other than glow starters) – Performance requirements This Malaysian Standard specifies general performance requirements for starting devices (starters and ignitors) for tubular fluorescent and other discharge lamps for use on a.c supplies up to 1 000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 5 kV. Price RM40 MS IEC 60968 : 2006 Self-ballasted lamps for general lighting services – Safety requirements This standard specifies the safety and interchangeability req uirements together with the test methods and conditions required to show compliance of tubular fluorescent and other gas – discharge lamps with integrated means for controlling starting and stable operation (self-ballasted lamps) intended for domestic and similar general lighting purposes having – a rated wattage up to 60 W, - a rated voltage of 100 V to 250 V; - Edison screw or bayonet caps. The requirements of this standard relate only to type testing. Price RM20
18
MS IEC 60969 : 2006 Self-ballasted lamps for general lighting services – Performances requirements This standard specifies the performance requirements together with the test methods and conditions required to show compliance of tubular fluorescent and other gas – discharge lamps with integrated means for controlling starting and stable operation (self-ballasted lamps) intended for domestic and similar general lighting purposes having – a rated wattage up to 60 W, - a rated voltage of 100 V to 250 V; - Edison screw or bayonet caps. Price RM20
MS IEC 60570-2-1 : 2003 Electrical supply track systems for luminaires – Part 2-1: Mixed supply system – Classes I and III This Malaysian standard applies to mixed supply track systems for connecting both class I and class III luminaires simultaneously, but in different track openings to the electrical supply, with two or more poles with a maximum nominal voltage of 440 V between poles (live conductors), maximum nominal frequency of 60 Hz and a maximum nominal current per conductor of 16 A for a class I sector and 25 A for a class III sector. Price RM10
MS IEC 61048 : 2006 Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp circuits - General and safety requirements (First revision) This standard states the requirements for both self-healing and nonself-healing continuously rated a.c. capacitors of up to and including
MS IEC 60598-1 : 2006 Luminaires – Part 1: General requirements and tests (Second revision). This Malaysian Standard specifies the general requirements for luminaries, incorporating electric sources for operation from supply voltages up to 1000 V. The requirements and related tests of this standard cover: classification, marking, mechanical construction and electrical construction. Price RM190
2.5 kvar, and not less than 0.1 µF, having a rated voltage not exceeding 1,000 V, which are intended for use in discharge lamp circuits* operating at 50 Hz or 60 Hz and at altitudes up to 3,000 m. It also covers capacitors intended for connection in shunt or in series with the lamp circuit or an effective combination of these and only those impregnated or unimpregnated capacitors, having a dielectric of paper, plastic film or a combination of both, either metallized or with metal foil electrodes. Price RM40 MS IEC 61050 : 2001 Transformers for tubular discharge lamps having a no-load output voltage exceeding 1 000 V (generally called neontransformers) - General and safety requirements - Section 1 : General requirements Price RM50 MS IEC 61195 : 2001 Double-capped fluorescent lamps - Safety specifications Price RM30 MS IEC 61199 : 2001 Single-capped fluorescent lamps - Safety specifications This Malaysian Standard specifies the safety requirements for singlecapped fluorescent lamps for general lighting purposes of all groups having 2G7, 2GX7, GR8, 2G10, G10q, GR10q, GX10q, GY10q, 2G11, G23, GX23, G24, GX24 and GX32 caps. Price RM40
29.140.40
Luminaires
MS 983 : 2004 ‘ KELUAR’ signs (Internally illuminated) - Specifications (Third revision) This Malaysian Standard relates to internally illuminated box type ‘KELUAR’ signs which are constructed for surface mounting or capable of being recessed into a wall or designed to be rigidly suspended from suitable brackets or fixings. Price RM20
MS IEC 60598-2-1 : 1997 Luminaires-Part 2 : Particular requirements - Section One - Fixed general purpose luminaires. This part of the standard specifies requirements for fixed general purpose luminaires for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages not exceeding 1,000 V. It is to be read in conjunction with those sections of Part 1 to which reference is made. This standard includes Amendment 1:1987 to IEC 598-2-1:1979. This standard supersedes MS 619:Pt. 2:Sec. 2.2:1983. Price RM20 MS IEC 60598-2-2 : 1998 Luminaires-Part 2 : Particular requirements - Section Two Recessed luminaires. This standard specifies the requirements for recessed luminaires for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages not exceeding 1,000 V. this section does not apply to air-handling or liquid-cooled luminaires. It is to be read in conjunction with those sections of Part 1 to which reference is made. Price RM20 MS IEC 60598-2-3 : 2006 Luminaires-Part 2-3 : Particular requirements - Luminaires for road and street lighting (First revision) This part of the standard specifies requirements for luminaires for road and street lighting and other outdoor lighting appli cations; tunnel lighting; column-integrated luminaries with a minimum total height above normal ground level of 2.5 m and for use with electrical lighting sources on supply voltages not exceeding 1000 V. Price RM20 MS IEC 60598-2-4 : 2003 Luminaires – Part 2 : Particular requirements – Section 4 : Portable general purpose luminaires (First revision) This Malaysian Standard specifies the requirements for portable general purpose luminaires, other than handlamps, for use with tungsten filaments, tubular fluorescent and other discharge lamps on supply voltages not exceeding 250 V. This Malaysian Standard cancels and replaces MS IEC 598-2-4 : 1997. Price RM20 MS IEC 60598-2-5 : 2006 Luminaires : Part 2-5 : Particular requirements – Floodlights (First revision) Specifies requirements for floodlights for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages not exceeding 1 000 V. It is to be read in conjunction with those sections of IEC 60598-1 to which reference is made. Price RM10
19
MS IEC 60598-2-6 : 2003 Luminaires – Part 2: Particular requirements – Section 6: Luminaires with built-in transformers for filament lamps This section of MS IEC 60598-2 specifies requirements for luminaire with built-in transformers for filament lamps, with supply voltages and output voltages not exceeding: 1 000 V for class I and class II luminai res and 250 V for class 0 luminaires. Price RM30
discharge lamps on supply voltages not exceeding 1000V. This section does not cover luminaires not in contact with water (e.g. mounted behind a glass panel which is separate from the luminaires) or hand-held or portable luminaires. Price RM20
MS IEC 60598-2-7 : 2003 Luminaires – Part 2 : Particular requirements – Section 7 : Portable luminaires for garden use This section of Part 2 of MS IEC 60598 specifies requirements for portable pedestal luminaires for use in places such as gardens and for portable luminaires for use in places such as flower beds, for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages not exceeding 250 V. It is to be read in conjunction with those sections of Part 1 to which reference is made. Price RM20 MS IEC 60598-2-8 : 2006 Luminaires-Part 2-8 : Particular requirements – Handlamps (First revision) This standard specifies the requirements for handlamps and similar portable luminaires which are held in the hand when used, for use with tungsten filament and tubular fluorescent lamps on supply voltages not exceeding 250 V. It is to be read in conjunction with those sections of Part 1 to which reference is made. Price RM20 MS IEC 60598-2-10 : 2006 Luminaires-Part 2-10 : Particular requirements - Portable luminaries for children (First revision). This standard specifies the requirements for portable luminaries for children and for use with tungsten filament lamps or single capped fluorescent lamps on supply voltages not exceeding 24 V (SELV). It is to be read in conjunction with those sections of Part 1 to which reference is made. Price RM20 MS IEC 60598-2-11 : 2006 Luminaires-Part 2-11 : Particular requirements - Aquarium luminaries This standard specifies the requirements for household aquarium luminaries for use with tungsten filament, tubular fluorescent other discharge lamps on supply voltages not exceeding 1000 V. Price RM20 MS IEC 60598-2-17 : 2003 Luminaires – Part 2 : Particular requirements – Section 17 : Luminaires for stage lighting, television and film studios
MS IEC 60598-2-19 : 2003 Luminaires – Part 2 : Particular requirements – Section 19 : Air-handling luminaries (Safety requirements) This Malaysian Standard specifies the safety requirements for airhandling luminaires for use with a ventilation space (plenum), for use with tubular flourescent lamps on supply voltage not exceeding 1 000 V. Price RM40 MS IEC 60598-2-20 : 1998 Luminaires-Part 2 : Particular requirements - Section 20 – Lighting chains. This Malaysian Standard the requirements for lighting chains fitted with series or parallel connected incandescent lamps for use either indoors or outdoors on supply voltages not exceeding 250 V. Price RM30 MS IEC 60598-2-23 : 2003 Luminaires – Part 2 : Particular requirements – Section 23 : Extra low voltage lighting systems for filament lamps This Malaysian Standard specifies requirements for extra low voltage systems for filament lamps intended for ordinary use on supply voltages not exceeding 1 000 V. Price RM20 MS IEC 60598-2-24 : 2006 Luminaires – Part 2-24 : Particular requirements – Luminaires with limited surface temperature This section of MS IEC 60598-2 specifies requirements for luminaires intended for use where the necessity of limited temperature on the outer surface exists, due to risk of combustible dust accumulating on the luminaries, but where the risk of explosion in the atmosphere does not exist. The luminaries are for use with electric light sources on supply voltages not exceeding 1000 V.. Price RM10 MS IEC 60598-2-25 : 2001 Luminaires for use in clinical areas of hospitals and health care buildings This section of MS IEC 60598-2 details specific requirements for luminaires for use with tungsten filament, fluorescent and other discharge lamps on supply voltages not exceeding 1 000 V for use in clinical areas in which medical treatment, examination and medical care takes place in hospitals and health care buildings. Price RM30
MS IEC 60682 : 2003 (outdoor and indoor) Standard method of measuring the pinch temperature of This section of Part 2 of MS IEC 60598 specifies requirements for quartz-tungsten-halogen lamps stage, television and film studio luminaires (including spot and floodThis Malaysian Standard is identical with IEC 60682:1980 and its lighting projectors), for use with tungsten filament, tubular fluores Amendment 1:1987. This Malaysian Standard specifies details of cent and other discharge lamps on supply voltages not exceeding the type of thermocouple to be used to measure the pinch tempera1000 V. It is to be read in conjunction with those sections of Part 1 ture of quartz-tungsten-halogen amps, the methods of preparation to which reference is made. Note. A hanger (stirrup) is a part of of the lamp and thermocouple, and the measurement to be made. the luminaire. Price RM40 Price RM20 MS IEC 60598-2-18 : 1998 Luminaires-Part 2 : Particular requirements - Section 18 – Luminaires for swimming pools and similar applications. This standard specifies the requirements for fixed luminaires intended for use in water, or in contact with water, in for example, the basins of swimming pools, fountains, paddling pools, and garden pools, for use with tungsten filament, tubular fluorescent and other
20
MS IEC 60901 : 2003 Single-capped fluorescent lamps – Performance specifications This Malaysian Standard specifies the performance requirements for single-capped fluorescent lamps for general lighting service. Price RM200
MS IEC 60192 : 2003 Low pressure sodium vapour lamps – Performance specifications This Malaysian Standard specifies the methods of test to be used for determining the characteristics of low pressure sodium vapour lamps of the integral type, both U-shaped and line ar, operating on a.c mains 50 Hz or 60 Hz. Price RM40
29.140.99
Other standards related to lamps
MS IEC 60188 : 1999 High-pressure mercury vapour lamps States the methods of test to be used for determining the characteristics of high-pressure mercury vapour lamps with or without a red correcting fluorescent coating operating on a.c. mains with a ballast satisfying the requirements of IEC 262 : Ballasts for High Pressure Mercury Vapour lamps. These requirements relate only to type testing. Details of maximum lamp outlines are also included for guidance in luminaire design. This standard is identical with IEC 60188 : 1974. Price RM40 MS IEC 60634 : 1999 Heat test source (H.T.S.) lamps for carrying out heating tests on luminaires Specifies requirements for heat test source (H.T.S.) lamps used for carrying out those thermal tests of IEC 60598 which primarily check the influence of heat conducted through the lamp cap as well as of convection. For a description of the origin and philosophy of this standard see Annex A. Where H.T.S. lamps are not available, an alternative heat test source (A.H.T.S.) lamp may be used. This standard is identical with IEC 60634 : 1993. Price RM20 MS IEC 60925 : 2003 DC supplied electronic ballasts for tubular fluorescent lamps Performance requirements Section one - General performance requirements. This standard specifies general performance requirements for electronic ballasts for use on d.c. supplies having rated voltages not exceeding 250 V, associated with fluorescent lamps. Complying wit 60081. It shall be read in conjunction with lEC 60924. Performance requirements for electronic ballasts for general, public transport and aircraft lighting are specified in Sections Two, Three and Four of this standard. Price RM30 MS IEC 61347-1 : 2003 Lamp controlgear - Part 1: General and safety requirements This part of MS IEC 61347 specifies general and safety requiremen ts for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz. This standard also covers lamp control gear for lamps which are not yet standardized. Tests dealt with in this standard are type tests. Requirements for testing individual lamp control gear during production are not included. Requirements for semi-luminaires are given in lEC 60598. In addition to the requirements given in this standard, annex B sets out general and safety requirements applicable to thermally protected lamp controlgear. Annex C sets out additional general and safety requirements as they apply to electronic lamp controlgear with means of protection against overheating. Price RM70 MS IEC 61347-2-1 : 2003 Lamp controlgear - Part 2-1: Particular requirements for starting devices (other than glow starters)
This part of MS lEC 61347 specifies particular safety requirements for starting devices (starters other than glow starters and ignitors) for fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 100 kV and which are used in combination with lamps and ballasts covered in lEC 60081, lEC 60188, lEC 60192, lEC 60662, lEC 60901, lEC 61167, lEC 61195, lEC 61199, lEC 61347-2-8 and . lEC 61347-2-9. It does not apply to glow starters or starting devices which are incorporated in discharge lamps or which are manually operated. Preheat transformers for fluorescent lamps are covered by lEC 61347-2-8. Price RM30 MS IEC 61347-2-2 : 2003 Lamp controlgear - Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps This part of (lEC 61347 specifies particular safety requirements for electronic step-down convertors for use on d.c. supplies up to 250 V or a.c.. supplies up to 1 000 V at 50 Hz or 60 Hz and rated output voltage =50 V r.m.s. at a frequency deviating from the supply frequency or =50 unsmoothed d.c. between conductors or between any conductor and earth, associated with tungsten-halogen lamps as specified in lEC 60357 and other filament lamps. Price RM40 MS IEC 61347-2-3 : 2003 Lamp controlgear - Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps This part of MS IEC 61347 specifies particular safety requirements for electronic ballasts for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in lEC 60081 and ,lEC 60901, and other fluorescent lamps for high-frequency operation. Particular requirements for electronic ballasts with means of protection against overheating are given in annex C. Particular requirements for a.c./ d.c. supplied electronic ballasts for maintained emergency lighting are given in annex J. Performance requirements are the subject of lEC 60929. Price RM30 MS IEC 61347-2-4 : 2003 Lamp controlgear - Part 2-4: Particular requirements for d.c. supplied electronic ballasts for general lighting This part of MS IEC 61347 specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from transient and surge-free power sources, operated directly from batteries without charging equipment as used in leisure equipment, for example, caravans, etc. Price RM20 MS IEC 61347-2-5 : 2003 Lamp controlgear - Part 2-5: Particular requirements for d.c. supplied electronic ballasts for public transport lighting This part of lEC 61347 specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from power sources likely to have attendant transients and surges, for example, for road and railway vehicles, tramcars, and craft used for public transport. Performance requirements are the subject of lEC 60925. Price RM30 MS IEC 61347-2-6 : 2003 Lamp controlgear - Part 2-6: Particular requirements for d.c. supplied electronic ballasts for aircraft lighting This part of MS IEC 61347 specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from power sources likely to have attendant transients and surges such as in aircraft. Performance requirements are the subject of lEC 60925. Price RM20
21
MS IEC 61347-2-7 : 2003 Lamp controlgear - Part 2-7 : Particular ‘requirements for d.c. supplied electronic ballasts for emergency lighting. This part of IEC 61347 specifies particular safety requirements for d.c. supplied electronic ballasts for maintained and I)on-maintained emergency lighting purposes. Price RM20 MS IEC 61347-2-8 : 2003 Lamp controlgear - Part 2-8 : Particular requireme nts for ballasts for fluorescent lamps This part of MS IEC 61347 specifies safety requirements for ballasts, excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with fluorescent lamps with or without pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in IEC 60081 and 60901. Price RM30 MS IEC 61347-2-9 : 2003 Lamp controlgear - Part 2-9 : Particular requireme nts for ballasts for discharge lamps . (excluding fluorescent lamps) This part of IEC 61347 specifies particular safety requirements for ballasts for discharge lamps uch as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. The standard covers inductive-type ballasts for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with discharge lamps, having rated wattages, dimensions and characteristics as specified in lEC 60188, lEC 60192 and lEC 60662. Price RM30 MS IEC 61347-2-10 : 2003 Lamp controlgear - Part 2-10 : Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) This part of MS IEC 61347 specifies particular requirements for electronic invertors and convertors for high-frequency operation of tubular coldcathode discharge lamps used in signs and luminous-discharge tube installations and operating with an output voltage exceeding 1 000 v but not exceeding 10 000 V for direct connection to supply voltages not exceeding 1 000 V at 50 Hz or 60 Hz or 1 000 V d.c. Price RM30
29.160.01
Rotating machinery
MS IEC 60034-3 : 2006 Rotating electrical machines – Part 3 : Specific requirements for cylindrical rotor synchronous machines This Malaysian Standard applies to threephase cylindrical rotor synchronous machines, having rated outputs of 10 MVA (or MW) and above. It supplements th e basic requirements for rotating machines given in IEC 60034-1. The special requiremen ts of machines continuously fed by inverters are not covered by this standard. Common requirements for all cylindrical rotor machines are prescribed together with the specific requirements for air for hydrogen or for liquid cooled cylindrical rotor synchronous machines. Price RM30 MS IEC 60034-5 : 2006 Rotating electrical machines – Part 5 : Specific degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification This Malaysian Standard applies to the classification of degrees of
22
protection provided by enclosures for rotating electrical machines. It defines the requirements for protective enclosures that are in all other respects suitable for their intended use and which , from the point of view of materials and workmanship ensure that the properties dealt with in this standard are maintaining under normal conditions of use. Price RM290 MS IEC 60034-6 : 2006 Rotating electrical machines – Part 6 : Methods of cooling (IC code) This Malaysian Standard identifies the circuit arrangements and the methods of movement of the coolant in rotating electrical machine, classifies the methods of cooling and gives a designation system for them. Price RM210 MS IEC 60034-7 : 2006 Rotating electrical machines – Part 7 : Classification of types of construction, mounting arrang ements and terminal box position (IM code) This Malaysian Standard specifies the IM code, a classification of types of construction, mounting arrangements and the terminal box position of rotating electrical machines. Price RM290
29.160.01
Rotating machinery in general
MS IEC 60034-2 : 2005 Rotating electrical machines – Part 2 : Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles) This Malaysian Standard applies to d.c machines and to a.c synchronous and induction machines of all sizes within the scope of MS IEC Publication 34-1. the principles can, however be applied to other types of machines such as rotary convertors, a.c commutator motors and single-phase induction motors for which other methods of determining losses are generally used. Price RM90 MS IEC 60034-8 : 2006 Rotating electrical machines – Part 8 : Terminal markings and direction of rotation This Malaysian Standard applies to a.c and d.c machines and specifies: a) rules for the identification of winding connection points; b) marking of winding terminals; c) direction of rotation, d) relationship between terminal markings and direction of rotation; e) terminal marking of auxiliary devices, f) connection diagrams of machines for common applications. Price RM300
29.160.40
Generating sets
MS 1403 : 1996 (2003) Electricity generating sets - Portable (up to 5kW). This Malaysian Standard specifies requirements for self-contained transportable electricity generating sets (hereinafter referred to as ‘generating sets’) driven by internal combustion engines and intended to provide an independent 50Hz a.c. supply of low voltage, singlephase at 240V. They may be portable or transportable. Price RM40
29.180
Transformers. Reactors
MS 768 : 1982 General rules for power transformers (not exceeding 1 KVA rating) for electronic equipment. Covers definitions, design, construction and electrical performance for high phase power transformers with iron cones. Price RM10 MS 935 : 1984 Code of practice for loading guide for oil-immersed transformers. Establishes the permissible loading, under certain defined conditions, for the guidance of users and to help planners in choosing the rated power required for new installations. Price RM50 MS 1202 : 1991 Specification for current transformers. This Malaysian Standard specifies the requirements for current transformers suitable for frequencie s of 15 Hz to 100 Hz and intended for use with electrical measuring instruments and electrical protective devices such as are covered, in general, by the following: MS 859, MS 925, BS 90, BS 142 and BS 3950. It also covers transformers for operating circuit-break trip coils. Price RM60 MS 1700 : 1998 Isolating transformers and safety isolating transformers requirements. This Malaysian Standard is identical with EN 60742 : 1989. This standard specifies the requirements for stationary or portable singlephase or polyphase, air-cooled isolating and safety isolating transformers. This standard shall supersede MS 936 : 1984. Price RM130
MS IEC 60076-1 : 2005 Power transformers – Part 1 : General. This Malaysians Standards applies to three-phase and single-phase power transformers (including auto-transformers) with the exception of certain categories of small and special transformers. Price RM50 MS IEC 60076-2 : 2005 Power transformers – Part 2 : Temperature rise. This Malaysian Standard identifies transformers according to their cooling methods, defines temperature-rise limits and details the methods of test for temperature-rise measurements. It applies to transformers as defined in the scope of MS IEC 60076-1:2005. Price RM40 MS IEC 60076-3 : 2005 Power transformers : Part 3 : Insulation levels, dielectric tests and external clearances in air. This Malaysian Standards applies to single-phase and three-phase oil-immersed power transformers (including auto-transformers) with the exception of certain small and special transformers. It identifies transformer windings to their highest voltage for equipment at Um associated with their corresponding rated insulation levels and details the relevant applicable dielectric tests and minimum external clearances in air between live parts of bushings and to objects at earth potential. Price RM60
This Malaysian Standards gives guidance and explanatory comments on the existing procedures for lightning and switching impulse testing of power transformers to supplement the requirements of MS IEC 60076-3. It is also generally applicable to the testing of reactors. Modifications to power transformers procedures being indicated where required. Price RM70 MS IEC 60076-5 : 2005 Power transformers : Part 5 : Ability to withstand short circuit. This Malaysian Standards identifies the requirements for power transformers to sustain without damage the effects of overcurrents originated by external short circuits. It describes the calculation procedures used to demonstrate the thermal ability of a power transformer to withstand such overcurrents and both the special test and the calculation method used to demonstrate its ability to withstand the relevant dynamic effects. The requirements apply to transformers as defined in the scope of IEC 60076-1. Price RM30 MS IEC 60076-8 : 2005 Power transformers : Part 8 : Application guide. This Malaysian Standards applies to power transformers complying with the series of publication MS IEC 60076. It is intended to provide information to users about : - certain fundamental service characteristics of different transformer connections and magnetic circuit design, with particular reference to zero-sequence phenomena; system fault currents in transformers with YNynd and similar connections; parallel operation of transformers, calculation of voltage drop or rise under load and calculation of load loss for three-winding load combinations; selection of rated quantities and tapping quantities at the time of purchase, based on prospective loading cases; application of transformers of conventional design to convertor loading; measuring technique and accuracy in loss measurement. Price RM90 MS IEC 60076-10 : 2005 Power transformers : Part 10 : Determination of sound levels This Malaysian Standards defines sound pressure and sound intensity measurement methods by which sound power levels of transformers, reactors and their associated cooling auxiliaries may be determined. Price RM40 MS IEC 61558-1 : 2005 Safety of power transformers, power supply units and similar – Part 1 : General requirements and tests Price RM140 MS IEC 61558-2-1 : 2005 Safety of power transformers, power supply units and similar – Part 2-1 : Particular requirements for separating transformers for general use Price RM20 MS IEC 61558-2-2 : 2005 Safety of power transformers, power supply units and similar – Part 2-2 : Particular requirements for control transformers Price RM20
MS IEC 60076-4 : 2005 Power transformers : Part 4 : Guide to the lightning impulse and switching impulse testing – Power transformers and reactors.
23
MS IEC 61558-2-3 : 2005 Safety of power transformers, power supply units and similar – Part 2-3 : Particular requirements for ignition transformers for gas and oil burners Price RM20 MS IEC 61558-2-4 : 2005 Safety of power transformers, power supply units and similar – Part 2-4 : Particular requirements for isolating transformers for general use Price RM20 MS IEC 61558-2-5 : 2005 Safety of power transformers, power supply units and similar – Part 2-5 : Particular requirements for shaver supply units Price RM20
MS IEC 60478-4 : 1996 Stabilized power supplies, d.c. output : Part 4 : Tests other than radio-frequency interference. This Malaysian Standard applies to stabilized power supplies designed to supply d.c. power from an a.c. or d.c. source for applications such as, but not necessarily limited to, the following : computers telecommunications laboratories industrial equipment. Price RM50
MS IEC 61558-2-6 : 2005 Safety of power transformers, power supply units and similar – Part 2-6 : Particular requirements for safety isolating transformers for general use Price RM20
29.200
MS IEC 60478-3 : 1996 Stabilized power supplies, d.c. output : Part 3 : Reference levels and measurement of conducted electromagnetic interference (EMI). This Malaysian Standard specifies the measuring equipment and techniques to be used in assessing the conducted electromagnetic interference (EMI) generated by stabilized power supplies and especially by switched-mode power supplies. It also specifies the reference levels, to be quoted by the manufacturer, of radio-frequency interference voltage measured at the source terminals and at the load terminals. Related mainly to power supplies for which the source current required does not exceed 24A. The techniques employed follow the general principles given in CISPR publications. Requirements for measurements of radiated interference have not been included in this standard. Price RM20
Rectifiers. Converters. Stabilized power supply
MS IEC 60335-2-29 : 2005 Household and similar electrical appliances – Safety – Part 2-29 : Particular requirements for battery chargers This Malaysian Standard deals with safety of electric battery charge rs for household and similar use having an output at safety extra-low voltage, their rated voltage being not more than 250 V. Price RM30 MS IEC 60478-1 : 1996 Stabilized power supplies, d.c. output : Part 1 : Terms and definitions. This Malaysian Standard applies to stabilized power supplies designed to supply d.c. power from an a.c. or d.c. source for applications such as, but not necessarily limited to, the following : - computers- telecommunicationslaboratories - indus trial equipment. Price RM30 MS IEC 60478-2 : 1996 Stabilized power supplies, d.c. output : Part 2 : Method of specifying rating and performance. This Malaysian Standard applies to the following information shall be permanently affixed to the power supply: (a) name of manufacturer or supplier; (b) model number; (c) serial number (optional); (d) output ratings : rating values or rated ranges of values for output voltage and current; (e) input ratings; nominal values for source voltage; source current and frequency, number of phases; (f) protection class. The performance of a stabilized power supply shall comply with the specified values of the quantities listed in the manufacture’s data sheet or other documents mutually agreed on by the manufacturer and user. Price RM20
24
MS IEC 61204 : 1996 Low-voltage power supply devices, d.c. output - Performance characteristic and safety requirements. This Malaysian Standard describes a method for specifying requirements for low-voltage power supply devices (including switching types) providing d.c. output (s) up to 200 V d.c. at power level of up to 30 kW, operating from a.c. or d.c. source voltages of up to 600 V. The devices are for use within class 1 equipment or freestanding operation when used with adequate electrical and mechanical protection. Price RM40 MS IEC 61204-3 : 2006 Low-voltage power supply d.c. output – Part 3 : Electromagnetic compatibility (EMC) This Malaysian Standard specifies electromagnetic compatibility (EMC) requirements for power supply units (PSUs) providing d.c output (s) up to 200 V at power level of up to 30 kW, operating from a.c. or d.c. source voltages of up to 600 V. The devices are for freestanding operation or for use in other equipment when used with adequate electrical and mechanical protection. Price RM40
29.220.01
Galvanic cells and batteries in general
MS 45 : 1991 Specification for batteries for automobiles (First revision). This Malaysian Standard specifies lead-acid storage butteries, hereinafter referred to as ‘batteries’. with a voltage of 12 V used primarily for starting, lighting, ignition, etc. of automobiles. However, this standard is not applicable to batteries for electric vehicles and motorcycles. Price RM30 MS 277 : 1996 Specification for motorcycle batteries (Second revision). This revised Malaysian Standard specifies lead-acid storage batteries, hereinafter referred to as ‘batteries’, primarily for lighting, ignition, and other electrical loads of motorcycles. The purpose of this standard also specifies the characteristics and test methods relating to ba tteries for lighting and ignition. This standard shall supersede MS 277 : 1989. Price RM20
29.220.10
Primary cells and batteries
29.240.01
MS 66 : Part 1 : 1999 Specification for primary cells and batteries : Part 1 : General (Second revision) Applies to primary cells and batteries based on any electrochemical system. The objects of its publication are : a) to ensure the electrical and physical interchangeability of products from different manufacturers; b) to limit the number of battery types; c) to define a standard of quality and provide guidance for its assessment; d) to provide guidance on matters of safety. These objects are achieved by specifying nomenclature, dimensions, polarity, terminals, marking, test conditions and service output requirements for each battery. This standard supersedes MS 66 : 1987. Price RM50 MS 66 : Part 2 : 1999 Specification for primary cells and batteries : Part 2 : Specification sheets Specifies dimensions together with outline drawings of batteries, conditions and minimum duration of discharges and application. Price RM70
29.220.20
Power transmission and distribution networks in general
MS 1142 : 1989 Specification for hard-drawn copper and power copper-cadmium conductors for over-head transmission purposes. Specifies requirements for hard-drawn copper and copper cadmium solid and stranded circular conductors for overhead power transmission systems. Price RM20 MS 1143 : 1989 Specification for aluminium alloy stranded conductor for overhead power transmission. Covers requirements for heat-treated aluminium-magnesium-silicon alloy stranded conductors for overhead power transmission; values for physical properties, sizes of wires and of stranded conductors; tolerances on dimensions, mechanical properties and electrical resistivity; modules of elasticity and code names for use when ordering. Price RM20
Acid secondary cells and batteries
MS 68 : 1991 Specification for containers for lead acid batteries (First revision). This Malaysian Standard lays down the requirements and the methods of test for containers normally used in the assembly of leadacid storage batteries. This Malaysian Standard specifies the synthetic resin and ebonite containers, hereinafter referred to as the ‘container’, to be used for lead-acid batteries. Remarks: The units and values used in this standard are in accordance with the International System of Units (SI) and ore ap pended for reference. Price RM10 MS 994 : 1990 Specification for water for lead-acid batteries. Specifies the grade A water for lead acid batteries. Also states limit of conductivity measures at 20 °C. Distilled or deionized water is being used for the grade A water. Price RM10
29.240.10
Substations. Surge arresters
MS IEC 60335-2-15 : 2004 Household and similar electrical appliances – Safety – Part 2-15 : Particular requirements for appliances for heating liquids This clause of part 1 is replaced by the following. This International Standard deals with the safety of electrical appliances for heating liquids for household and similar purposes, their rated voltage being not more than 250 V. Price RM30 MS IEC 61643-1 : 2006 Low-voltage surge protective devices – Part 1 : Surge protective devices connected to low-voltage power distribution systems – Requirements and tests (First revision) This part of IEC 61643 is applicable to devices for surge protection against indirect and direct effects of lightning or other transient overvoltages. These devices are packaged to be connected to 50/ 60 Hz a.c and d.c power circuits, and equipment rated up to 1 000 V r.m.s. or 1 500 V d.c. Price RM90 MS IEC 61643-12 : 2004 Low-voltage surge protective devices – Part 12 : Surge protective devices connected to low-voltage power distribution systems – Selection and application principles
25
This part of IEC 61643 describes the principles for selection, operation, location and co-ordination of SPDs to be connected to 50 Hz to Hz a.c. and to d.c. power circuits and equipment rated up to 1 000 V r.m.s. or 1 5000 V d.c. Price RM130 MS IEC 61643-21 : 2004 Low-voltage surge protective devices – Part 21: Surge protective devices connected to telecommunications and signalling networks – Performance requirements and testing methods This International Standard is applicable to devi ces for surge protection of telecommunications and signalling networks against indirect and direct effects of lighting or other transient overvoltages. Price RM70
29.240.30
Control equipment for electric power systems
MS 925 : 1984 Specification for direct acting indicating electrical measuring instruments and their accessories. Applies to ammeters, voltmeters, single phase and polyphase watt meters for direct alternating current. Price RM60
29.260.10
Electrical installations for outdoor use
MS 556 : 1978 Specification for electrical safety code of private electric generating plant (First revision). Covers electrical supply conductors, plant and equipment in electrical supply stations installed in, owned and operated by a private establishment. The purpose of this code is to safe-guard persons from hazards arising from the installation, operation and maintenance of the above. Price RM30
29.260.20
Electrical apparatus for explosive atmospheres
MS 1591 : 2003 Electrical apparatus for explosive gas atmospheres – Part 16: Artificial ventilation for the protection of analyser (s) houses This Malaysian Standard provides the general principles of protection, by artificial ventilation, of analyzer (s) houses against the explosion hazards caused by internal release of flammable substances and, if applicable, against the hazard s caused by an external explosive gas atmosphere. It also gives the conditions in which electrical apparatus liable to cause ignition may be used in these analyser (s) houses. Price RM30 MS 1592 : 2003 Electrical apparatus for explosive gas atmospheres – Part 20 : Data for flammable gases and vapours, relating to the use of electrical apparatus. This Malaysian Standard gives guidance on the selection of appropriate
77. METALLURGY
26
electrical apparatus, protected by flame-proof enclosure or designed to be intrinsically safe, according to the gas or vapour in which it is intended to be used. Price RM40 MS 1712 : 2003 Electrical apparatus for explosive gas atmospheres – Classification of mixtures of gases or vapours with air according to their maximum experimental safe gaps and minimum igniting currents This Malaysian Standard provides guidance on the selection of the appropriate group or sub-group of electrical apparatus, protected by flameproof enclosure or designed to be intrinsically safe, according to the gas or vapour in which it is intended to be used. Price RM20 MS 1713 : 2003 Electrical apparatus for explosive gas atmospheres – Construction and use of rooms or buildings protected by pressurisation This Malaysian Standard defines the conditions in which an electrical apparatus liable to cause an ignition may be used in a room or building where flammable gases or vapours may be present. The ingress of these gases or vapours into the room is being prevented by maintaining inside it a protective gas at a higher pressure than that of the outside atmosphere. Price RM20 MS IEC 60079-0 : 2005 Electrical apparatus for explosive gas atmospheres – Part 0 : General requirements (First revision) This Malaysian Standard specifies the general requirements for construction, testing and marking of electrical apparatus, Ex cable entries and Ex components, intended for use in explosive gas atmospheres. Price RM80 MS IEC 60079-1 : 2005 Electrical apparatus for explosive gas atmospheres – Part 1 : Flameproof enclosures “d” (First revision) This Malaysian Standard contains the specific requirements for the construction and testing of electrical apparatus with the type of protection flameproof enclosure “d”, intended for use in potentially explosive gas atmospheres. Price RM80 MS IEC 60079-1-1 : 2004 Electrical apparatus for explosive gas atmospheres – Part 1-1 : Flameproof enclosures “d” – Method of test for ascertainment of maximum experimental safe gap This part of IEC 60079 describes a test method intended for the measurement of the maximum experimental safe gas- or vapourair mixtures under normal conditions of temperature 1 and pressure so as to permit the selection of an appropriate group of flameproof enclosures Price RM20 MS IEC 60079-2 : 2003 Electrical apparatus for explosive gas atmospheres – Part 2 : Pressurized enclosures “p” This part of MS IEC 60079 contains the specific requirements for the construction and testing of electrical apparatus with pressurized enclosures, of protection type “p”, intended for use in explosive gas atmospheres. The requirements contained in this standard are supplementary to those in MS IEC 60079-0. This standard specifies requirements for pressurized enclosures containing a limited release of a flammable substance. Price RM60
MS IEC 60079-4 : 2003 Electrical apparatus for explosive gas atmospheres. Part 4: Method of test for ignition temperature This method of test is intended for use in the determination of the ignition temperature of a chemically pure vapour or gas in air at atmospheric pressure. Price RM30 MS IEC 60079-5 : 2003 Electrical apparatus for explosive gas atmospheres – Part 5 : Powder filling “q” This part of MS IEC 60079 contains the specific requirements for the construction, testing and marking of electrical apparatus, parts of electrical apparatus and Ex components in the type of protection powder filling “q”, intended for use in potentially explosive atmospheres of gas, vapour and mist. Price RM30 MS IEC 60079-6 : 2003 Electrical apparatus for explosive gas atmospheres : Part 6 : Oil immersion “o”. This part of MS IEC 60079 specifies the requirements for the construction and testing of oil-immersed electrical apparatus, oilimmersed parts of electrical apparatus and Ex components in the type of protection “o” intended for use in potentially explosive atmospheres of gas , vapour and mist Price RM20 MS IEC 60079-7 : 2003 Electrical apparatus for explosive gas atmospheres – Part 7 : Increased safety “e” This part of MS IEC 60079 specifies the requirements for the design, construction, testing and marking of electrical apparatus with type of protection increased safety “e” intended for use in explosive gas atmospheres. This standard applies to electrical apparatus with a rated value of supply voltage not exceeding 11 kV r.m.s. a.c. or d.c.
MS IEC 60079-15 : 2003 Electrical apparatus for explosive gas atmospheres – Part 15 : Type of protection “n”. This part of MS IEC 60079 specifies requirements for the construction, testing and marking for Group 11 electrical apparatus with type of protection “n” intended for use in explosive gas atmospheres. This standard is applicable to non-sparking electrical apparatus and also to electrical apparatus with parts or circuits producing arcs or sparks or having hot surfaces which, if not protected in one of the ways specified in this standard, could be capable of igniting a surrounding explosive gas atmosphere.. Price RM90 MS IEC 60079-17 : 2003 Electrical apparatus for explosive gas atmospheres – Part 17 : Inspection and maintenance of electrical installations in hazardous areas (other than mines). This part of MS IEC 60079 is intended to be applied by users, and covers factors directly related to the inspection and maintenance of electrical installations within hazardous areas only. it does not include conventional requirements for electrical installations, nor the testing and certification of electrical apparatus. It does not cover Group 1 apparatus (applications for mines susceptible to firedamp). This standard supplements the requirements laid down in IEC 60364-661. Price RM40 MS IEC 60079-18 : 2005 Electrical apparatus for explosive gas atmospheres – Part 18 : Construction, test and marking of type of protection encapsulation “m” electrical apparatus (First revision) This part of MS IEC 60079 gives the specific requirements for the construction, testing and marking of electrical apparatus, parts of electrical apparatus and Ex components with the type of protection encapsulation “m”. Price RM40
Price RM80 MS IEC 60079-10 : 2003 Electrical apparatus for explosive gas atmospheres – Part 10 : Classification of hazardous areas. This part of MS IEC 60079 is concerned with the classification of hazardous areas where flammable gas or vapour risks may arise, in order to permit the proper selection and installation of apparatus for use in such hazardous areas. Price RM70 MS IEC 60079-11 : 2003 Electrical apparatus for explosive gas atmospheres – Part 11 : Intrinsic safety “I”. This part of MS IEC 60079 specifies the construction and testing of intrinsically safe apparatus, intended for use in potentially explosive atmospheres and for associated apparatus, which is intended for connection to intrinsically safe circuits which enter such atmospheres. Price RM100 MS IEC 60079-14 : 2003 Electrical apparatus for explosive gas atmospheres – Part 14 : Electrical installations in hazardous areas (other than mines). This part of MS IEC 60079 contains the specific requirements for the design, selection and erection of electrical installations in explosive gas atmospheres. These requirements are in addition to the requirements for installations in non-hazardous areas. This standard applies to all electrical equipment and install ations in hazardous areas whether permanent, temporary, portable, transportable or hand-held. It applies to installations at all voltages. This standard does not apply to electrical installations in mines susceptible to firedamp. Price RM70
MS IEC 60079-19 : 2003 Electrical apparatus for explosive gas atmospheres – Part 19 : Repair and overhaul for apparatus used in explosive atmospheres (other than mines or explosives). This part of MS IEC 60079: - gives instructions, principally of a technical nature, on the repair, overhaul, reclamation and modification of a certified apparatus designed for use in explosive atmospheres (other then mining applications or explosive processing and manufacture); - is not applicable to maintenance, other than when repair and overhaul cannot be disassociated from maintenance, neither does it give advice on cable entry systems which may require renewal when the apparatus is re-installed; - assumes that good engineering practices are adopted throughout. Price RM50 MS IEC 60079-25 : 2005 Electrical apparatus for explosive gas atmospheres – Part 25 : Intrinsically safe systems This Malaysian Standard contains the specific requirements for construction and assessment of intrinsically safe electrical systems, type of protection “i” intended for use as a whole or in part, in explosive atmospheres in Group II locations. This standard is intended for use by the designer of the system who may be a manufacturers, a specialist consultant or a member of the end-user’s staff. Price RM70
27
MS IEC 60079-26 : 2005 Electrical apparatus for explosive gas atmospheres – Part 26 : Construction, test and marking of group II zone 0 electrical apparatus This Malaysian Standard specifies the particular requirements for construction, test and marking for electrical apparatus of Group II intended for use in Zone 0 as defined in MS IEC 60079-10. This electrical apparatus, within the operational parameters specified by the manufacturers, ensures a very high level of protection that includes rare faults related to the apparatus of two faults occurring independently of each other. Price RM30 MS IEC TS 60079-27 : 2004 Electrical apparatus for explosive gas atmospheres – Part 27 : Fieldbus intrinsically safe concept (FISCO) This part of IEC 60079, which is a technical specification, contains the details of apparatus, systems and installation practice for use with the Fieldbus intrinsically safe concept (FISCO) and is based on the concepts of Manchester encoded, bus powered systems designed in accordance with IEC 61158-2 which is the physical layer standard for Fieldbus installations. Price RM20 MS IEC 61000-3-12 : 2005 Electromagnetic compatibility (EMC) – Part 3-12 : Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16 A and <_75 A per phase This Malaysian Standard deals with the limitation of harmonic currents injected into the public supply system. The limits given in thi s standard are applicable to electrical and electronic equipment with rated input current exceeding 16 A and up to and including 75 A per phase, intended to be connected to public low-voltage a.c distribution systems. Price RM40
29.260.99
Other electrical equipment for working in special conditions
MS 477 : 1977 Code of practice for protection of electrical power equipment against climatic conditions. Applies to electrical power equipment as distinct from telecommunication and allied electric equipment except where this forms an integral part of the power equipment. No guidance is given on the special precautions necessary for equipment used in aircraft. Price RM80
28
31. ELECTRONICS
31.020
Electronic components in general
MS 142 : 1973 Specification for precautions with respect to possible hazards when dealing with electronic equipment employing similar techniques Specifies precautions and general rules of behaviour when dealing with electronic equipment either for operational or maintenance purposes. This standard serves to form a basis for preparation of more comprehensive instructions as safety measures against possible hazards. Price RM30
31.040
Resistors
MS IEC 61643-331 : 2004 Component for low-voltage surge protec tive devices – Part 331: Specification for metal oxide varistors (MOV) This part of IEC 61643 is a test specification for metal oxide varistors (MOV). Which are used for applications up to 1 000 V a.c. or 1 5000 V d.c. in power line, or telecommunication, or signalling circuits. They are designed to protect apparatus or personnel, or both, from high transient voltages. Price RM30
31.040.01
Resistors in general
MS 763 : 1982 Specification for preferred number series for resistance and capacitors. Specifies preferred number series in two sections, Section 1 : for resistors and capacitors, Section 2 : for close tolerance resistors and capacitors. Price RM10
31.040.10
Fixed resistors
MS IEC 60062 : 2003 Marking code for resistors and capacitors This standard specifies marking codes for resistors and capacitors. The code specified in Clause 2 gives a colour coding for fixed resistors. It is intended for use with the values of the E6 to E192 series as specified in IEC Publication 63, Preferred Number Series of Resistors and Capacitors. The code specified in Clause 3 gives a system for marking resistance and capacitance values by means of letters and digits. The code specified in Clause 4 gives a system for marking the tolerance on resistance and capacitance values by means of a letter. The code specified in Clause 5 gives systems for marking of date codes on capacitors an d resistors by means of letters and digits. Price RM30
MS IEC 60115-1 : 2003 Fixed resistors for use in electronic equipment – Part 1: Generic specification This part of MS IEC 60115 is applicable to fixed resistors for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose. Price RM70
31.060
Capacitors
31.060.01
Capacitors in general
MS 279 : 1983 Specification for capacitors for use in tubular fluorescent, highpressure mercury and low-pressure sodium vapour discharge lamp circuits (First revision). Specifies requirements for both self-heating and non-self-heating capacitors of up to and including 2.5 Kvar. with capacitance of not less than 01.F and having rated voltage not exceeding 1Kv. Covers only impregnated or unimpregnated capacitors having a dielectric of paper, plastic film or combination of both, either metallized or with metal foil electrode. Does not include radio-interference suppress or capacitors. Price RM30 MS 763 : 1982 Specification for preferred number series for resistance and capacitors. Specifies preferred number series in two sections, Section 1 : for resistors and capacitors, Section 2 : for close tolerance resistors and capacitors. Price RM10
31.080.10
Diodes
MS IEC 61643-341 : 2004 Low-voltage surge protective devices – Part 341 : Specification for thyristor surge suppressors (TSS) This part of IEC 61643 is a test specification standard for thyristor surge suppressor (TSS) components designed to limit overvoltages and divert surge currents by clipping and crowbarring actions. Such components are used in the construction of surge protective devices, particularly as they apply to telecommunications. Price RM70
Diode
29
Resistor
Capacitor
31.100
Electronic Tubes
MS IEC 61643-311 : 2004 Components for low-voltage surge protective devices – Part 311 : Specification for gas discharge tubes (GDT) Gas discharge tubes (GDTs) are used for applications up to 1 000 V a.c or 1 500 V d.c. in communication or signalling circuits. They are defined as a gap, or series of gaps, in an encl osed discharge medium other than air. They are designed to protect apparatus or personnel, or both, from high transient voltage. This standard does not specify requirements applicable to complete surge protective devices, nor does it specify total requirements for GDTs employed within electronics devices, where precise coordination between GDT performance and surge protective device withstand capability is highly critical. Price RM30
Gas Discharge Tubes (GDT)
MS IEC 61643-321 : 2004 Component for low-voltage surge protective devices – Part 321 : Specification for avalanche breakdown diode (ABD) This part of IEC 61643 is applicable to avalanche breakdown diodes (ABDs) which represent one type surge protective device compon ent (hereinafter referred to as SPDC) used in the design and cons truction of surge protective devices connected to low-voltage power distribution systems, transmission, and signalling networks. Test specifications in this standard are for single ABDs consisting of two terminals. However, multiple ABDs may be assembled within a single package defined as a diode array. Each diode within the array can be tested to this specification. Price RM30
31.220.20
Switches
MS 590 : 1979 Specification for low-voltage air-break switches, air break disconnectors, air-break switch connectors and fuse combination units. Intended for equipment to be used in distribution circuits and motor circuits where rated voltage does not exceed 1000V a.c. or 1200V d.c.. Definitions cover types of devices constructional elements, conditions of operation, characteristics quantities. Also include markings and type tests required. Price RM50
30
NUMERICAL LISTING
Standards Number
Price (RM)
Page
Standards Number
24 25 25 25 3,5 5 5 5 5 18 18 29 5 9 9 5 24 6 18, 29 3 1 6 4 1 1 28 4 4 4 4 26 10 10 11 11 30 16 4 6 29 23 16 5 5 8 8
MS 859 : Part 3 : 1996 MS 860 : Part 1 : 1983 MS 925 : 1984 MS 935 : 1984 MS 938 : 1984 MS 944 : 1984 MS 946 : 1984 MS 948 : 1984 MS 983 : 2004 MS 994 : 1990 MS 1034 : 1986 MS 1039 : 1986 MS 1092 : 1987 MS 1093 : 1987 MS 1095 : 1987 MS 1141 : 2006 MS 1142 : 1989 MS 1143 : 1989 MS 1144 : 1998 MS 1202 : 1991 MS 1237 : 1991 MS 1238 : 1991 MS 1239 : 1991 MS 1240 : 1991 MS 1403 : 1996 (2003) MS 1428 : 1997 MS 1445 : Part 1 : 1998 MS 1445 : Part 3 : 1998 MS 1487 : 1999 MS 1534 : Part 1 : 2002 MS 1534 : Pt 2 : Sec. 1 : 2002 MS 1534 : Pt 2 : Sec. 2 : 2003 MS 1534 : Pt 2 : Sec. 3 : 2003 MS 1534 : Pt 2 : Sec. 4 : 2003 MS 1540 : 2002 MS 1577 : 2003 MS 1578 : 2003 MS 1579 : 2003 MS 1586 : Part 3 : 2003 MS 1591 : 2003 MS 1592 : 2003 MS 1700 : 1998 MS 1712 : 2003 MS 1713 : 2003 MS 1777 : Part 1 : 2005 MS 1777 : Part 2-1 : 2006 MS 1777 : Part 2-2 : 2006
MS MS 45 : 1991 MS 66 : Part 1 : 1999 MS 66 : Part 2 : 1999 MS 68 : 1991 MS 69 : 1995 MS 136 : 1995 MS 137 : 1973 MS 138 : 1995 MS 140 : 1987 MS 141 : Part 1 : 1993 MS 141 : Part 2 : 1993 MS 142 : 1973 MS 274 : 1995 MS 275 : Part 1 : 1975 MS 275 : Part 2 : 1975 MS 276 : 1987 MS 277 : 1996 MS 278 : 1987 MS 279 : 1983 MS 280 : 1975 MS 406 : 1996 MS 434 : 1976 MS 435 : 1976 MS 472 : Pt.2 :Sec. 2.9 :1983 MS 472 : Pt.3 :Sec. 3.1 :1986 MS 477 : 1977 MS 528 : 1977 MS 529 : 1977 MS 550 : 1978 MS 551 : 1978 MS 556 : 1978 MS 589 : Part 1 : 1997 MS 589 : Part 2 : 1997 MS 589 : Part 3 : 1998 MS 589 : Part 4 : 1998 MS 590 : 1979 MS 619 : Part 2-22 : 2005 MS 754 : 1981 MS 766 : Part 1 : 1982 MS 763 : 1982 MS 768 : 1982 MS 769 : 1982 MS 796 : 1982 MS 824 : 1983 MS 859 : Part 1 : 1999 MS 859 : Part 2 : 1989
30 50 70 10 30 40 20 20 60 50 30 30 60 30 40 20 20 40 30 20 10 20 20 10 100 80 10 20 30 40 30 70 70 90 40 50 30 20 20 10 10 50 20 20 40 20
31
Price (RM)
Page
20 20 60 50 20 20 30 60 20 10 20 80 10 10 80 50 20 20 70 60 20 10 10 20 40 30 110 100 30 40 20 20 20 20 10 30 30 50 20 30 40 130 20 20 30 20 30
9 1 26 23 3 1 1 14 19 25 9 11 5 5 6 11 3, 25 3, 25 1, 9 23 5 5 5 5 22 12 13 13 1 9 9 9 9 10 3 11 11 11 12 26 26 23 26 26 10 4 4
NUMERICAL LISTING
Standards Number MS 1777 : Part 2-3 : 2006 MS 1777 : Part 2-4 : 2006 MS 1778 : Part 1 : 2005 MS 1778 : Part 2 : 2005 MS 1779 : 2005 MS 1781 : 2005 MS 1782 : 2005 MS 1838 : 2005 MS 1840 : 2005 MS 1862 : 2005 MS 1863 : 2005 MS 1873 : 2005 MS 1873 : Part 21 : 2006 MS 1873 : Part 22 : 2006 MS 1936 : 2006 MS 2100 : 2006 MS 2101 : 2006 MS 2102 : 2006 MS 2103 : 2006 MS 2104 : 2006
Price(RM)
Page
20 20 30 20 10 120 90 10 300 20 20 70 20 20 100 20 20 20 20 20
10 10 18 18 4 14 14 4 14 3 3 10 13 10 1 4 4 4 4 4
90 30 290 210 290 300 20 40 50 30 100 50 40 60 70 30 90 40 80 80 20 60 30 30
22 22 22 22 22 22 1 1 16 29 17 23 23 23 23 23 23 23 26 26 26 26 27 27
Standards Number MS IEC 60079-6 : 2003 MS IEC 60079-7 : 2003 MS IEC 60079-10 : 2003 MS IEC 60079-11 : 2003 MS IEC 60079-14 : 2003 MS IEC 60079-15 : 2003 MS IEC 60079-17 : 2003 MS IEC 60079-18 : 2005 MS IEC 60079-19 : 2003 MS IEC 60079-25 : 2005 MS IEC 60079-26 : 2005 MS IEC TS 60079-27 : 2004 MS IEC 60081 : 2003 MS IEC 60115-1 : 2003 MS IEC 60155 : 1996 MS IEC 60183 : 2003 MS IEC 60188 : 2006 MS IEC 60192 : 2003 MS IEC 60228 : 2001 MS IEC 60229 : 2001 MS IEC 60238 : 1999 MS IEC 60269-1 : 2003 MS IEC 60269-2 : 2005 MS IEC 60269-2-1 : 2003 MS IEC 60269-3-1 : 2003 MS IEC 60269-4 : 2003 MS IEC 60269-4-1 : 2005 MS IEC 60287-1-2 : 2001 MS IEC 60287-2-1 : 2001 MS IEC 60287-2-2 : 2001 MS IEC 60287-3-2 : 2003 MS IEC 60320-1 : 2003 MS IEC 60320-2-2 : 2003 MS IEC 60331-11 : 2001 MS IEC 60331-21 : 2001 MS IEC 60331-23 : 2001 MS IEC 60331-25 : 2001 MS IEC 60332-1 : 2001 MS IEC 60332-2 : 2001 MS IEC 60335-2-15 : 2004 MS IEC 60335-2-29 : 2005 MS IEC 60335-2-95 : 2003 MS IEC 60335-2-97 : 2003 MS IEC 60360 : 1999 MS IEC 60357 : 2003 MS IEC 60364-7-702 : 2003 MS IEC 60399 : 2003
MS IEC
MS IEC 60034-2 : 2005 MS IEC 60034-3 : 2006 MS IEC 60034-5 : 2006 MS IEC 60034-6 : 2006 MS IEC 60034-7 : 2006 MS IEC 60034-8 : 2006 MS IEC 60038 : 2006 MS IEC 60050-426 : 2004 MS IEC 60061-4 : 2005 MS IEC 60062 : 2003 MS IEC 60064 : 2006 MS IEC 60076-1 : 2005 MS IEC 60076-2 : 2005 MS IEC 60076-3: 2005 MS IEC 60076-4 : 2005 MS IEC 60076-5 : 2005 MS IEC 60076-8 : 2005 MS IEC 60076-10: 2005 MS IEC 60079-0 : 2005 MS IEC 60079-1 : 2005 MS IEC 60079-1-1 : 2004 MS IEC 60079-2 : 2003 MS IEC 60079-4 : 2003 MS IEC 60079-5 : 2003
32
Price (RM)
Page
20 80 70 100 70 90 40 40 50 70 30 20 100 70 40 20 40 40 20 20 100 80 20 140 130 90 30 40 40 30 50 130 50 30 20 20 20 20 20 30 30 30 30 30 110 30 20
27 27 27 27 27 27 27 27 27 27 28 28 18 29 16 6 18 21 6 6 16 12 12 12 12 12 12 6 6 6 6 11 11 6 6 6 7 7 7 25 24 9 9 16 17 1 15
NUMERICAL LISTING
Standards Number
Price (RM)
Page
MS IEC 60400 : 1999 MS IEC 60423 : 2002 MS IEC 60432-1 : 2006 MS IEC 60432-2 : 2006 MS IEC 60432-3 : 2006 MS IEC 60439-1 : 2005
90 30 50 20 40 110
17 10 17 17 18 14
MS IEC 60439-2 : 2002 MS IEC 60439-3 : 2003 MS IEC 60439-4 : 2005 MS IEC 60439-5 : 2004 MS IEC 60478-1 : 1996 MS IEC 60478-2 : 1996 MS IEC 60478-3 : 1996 MS IEC 60478-4 : 1996 MS IEC 60502-1 : 1998 MS IEC 60502-2 : 1998 MS IEC 60502-4 : 1998 MS IEC 60529 : 2005 MS IEC 60570 : 2006 MS IEC 60570-2-1 : 2003 MS IEC 60598-1 : 2006 MS IEC 60598-2-1 : 1997 MS IEC 60598-2-2 : 1998 MS IEC 60598-2-3 : 2006 MS IEC 60598-2-4 : 2003 MS IEC 60598-2-5 : 2006 MS IEC 60598-2-6 : 2003 MS IEC 60598-2-7 : 2003 MS IEC 60598-2-8 : 2006 MS IEC 60598-2-9 : 2001 MS IEC 60598-2-10 : 2006 MS IEC 60598-2-11 : 2006 MS IEC 60598-2-17 : 2003 MS IEC 60598-2-18 : 1998 MS IEC 60598-2-19 : 2003 MS IEC 60598-2-20 : 1998 MS IEC 60598-2-23 : 2003 MS IEC 60598-2-24 : 2006 MS IEC 60598-2-25 : 2001 MS IEC 60630 : 2003 MS IEC 60634 : 1999 MS IEC 60662 : 2002 MS IEC 60669-1 : 2004 MS IEC 60669-2-1 : 2004 MS IEC 60669-2-2 : 2004 MS IEC 60669-2-3 : 2004 MS IEC 60682 : 2003 MS IEC 60809 : 2001
40 30 30 40 30 20 20 50 60 70 40 60 30 10 190 20 20 20 20 10 30 20 20 30 20 20 20 20 40 20 20 10 30 100 20 140 100 50 30 30 40 140
14 14 14 14 24 24 24 24 7 7 7 2 18 19 19 19 19 19 19 19 20 20 20 15 20 20 20 20 20 20 20 20 20 18 21 15 11 11 11 12 20 16
33
Standards Number MS IEC 60810 : 2001 MS IEC 60811-1-1 : 1997 MS IEC 60811-1-2 : 1997 MS IEC 60811-1-3 : 1997 MS IEC 60811-2-1 : 1997 MS IEC 60811-3-1 : 1997 MS IEC 60811-3-2 : 1997 MS IEC 60811-4-1 : 1997 MS IEC 60811-4-2 : 1997 MS IEC 60811-5-1 : 1997 MS IEC 60838-1 : 1999 MS IEC 60838-2-1 : 1999 MS IEC 60885-1 : 2003 MS IEC 60885-2 : 2003 MS IEC 60885-3 : 2003 MS IEC 60898-1 : 2003 MS IEC 60898-2 : 2003 MS IEC 60901 : 2003 MS IEC 60922 : 1995 MS IEC 60923 : 1995 MS IEC 60925 : 2003 MS IEC 60926 : 2001 MS IEC 60927 : 2003 MS IEC 60928 : 1995 MS IEC 60929 : 1995 MS IEC 60947-1 : 2004 MS IEC 60947-2 : 2000 MS IEC 60947-3 : 2000 MS IEC 60947-4-1 : 2005 MS IEC 60947-4-2 : 2005 MS IEC 60947-5-1 : 2005 MS IEC 60947-5-2 : 2005 MS IEC 60968 : 2006 MS IEC 60969 : 2006 MS IEC 60983 : 2002 MS IEC 61000-3-5 : 2000 MS IEC 61000-3-12 : 2005 MS IEC 61000-4-2 : 2002 MS IEC 61000-4-3 : 2001 MS IEC 61000-4-4 : 2000 MS IEC 61000-4-5 : 2000 MS IEC 61000-4-6 : 2000 MS IEC 61000-4-8 : 2000 MS IEC 61000-4-10 : 2000 MS IEC 61000-4-11 : 2000 MS IEC 61000-4-12 : 2000 MS IEC 61000-4-16 : 2000 MS IEC 61000-6-1 : 2000
Price (RM)
Page
40 40 30 20 30 30 30 40 30 30 40 20 10 10 40 130 30 200 70 40 30 50 40 40 60 180 140 60 100 90 100 110 20 20 60 20 40 40 40 40 50 50 40 40 30 50 40 30
16 7 7 7 7 7 8 8 8 8 17 17 8 8 8 12 13 20 15 15 21 16 18 15 15 14 13 12,13,14
14 14 12, 15 12, 15 18 19 15 2 28 2 2 2 2 2 2 2 2 2 2 3
NUMERICAL LISTING
Standards Number MS IEC 61000-6-3 : 2000 MS IEC 61000-6-4 : 2000 MS IEC 61008-1 : 2003 MS IEC 61008-2-1 : 2003 MS IEC 61008-2-2 : 2003 MS IEC 61009-1 : 2003 MS IEC 61009-2-1 : 2003 MS IEC 61009-2-2 : 2003 MS IEC 61046 : 2001 MS IEC 61047 : 2001 MS IEC 61048 : 2006 MS IEC 61049 : 1999 MS IEC 61050 : 2001 MS IEC 61126 : 2001 MS IEC 61228 : 2003 MS IEC 61167 : 1999 MS IEC 61195 : 2001 MS IEC 61199 : 2001 MS IEC 61204 : 1996 MS IEC 61204-3 : 2006 MS IEC 61347-1 : 2003 MS IEC 61347-2-1 : 2003 MS IEC 61347-2-2 : 2003 MS IEC 61347-2-3 : 2003 MS IEC 61347-2-4 : 2003 MS IEC 61347-2-5 : 2003 MS IEC 61347-2-6 : 2003 MS IEC 61347-2-7 : 2003 MS IEC 61347-2-8 : 2003 MS IEC 61347-2-9 : 2003 MS IEC 61347-2-10 : 2003 MS IEC 61537 : 2006 MS IEC 61540 : 2003 MS IEC 61549 : 2003 MS IEC 61558-1: 2005 MS IEC 61558-2-1: 2005 MS IEC 61558-2-2: 2005 MS IEC 61558-2-3: 2005 MS IEC 61558-2-4: 2005 MS IEC 61558-2-5: 2005 MS IEC 61558-2-6 : 2005 MS IEC 61643-1 : 2006 MS IEC 61643-12 : 2004 MS IEC 61643-21 : 2004 MS IEC 61643-311 : 2004 MS IEC 61643-321 : 2004 MS IEC 61643-331 : 2004 MS IEC 61643-341 : 2004
Price (RM)
Page
20 20 140 10 10 150 20 20 70 40 40 20 50 70 20 50 30 40 40 40 70 30 40 30 20 30 20 20 30 30 30 70 120 30 140 20 20 20 20 20 20 90 130 70 30 30 30 70
3 3 13 13 13 13 13 13 16 16 19 17 19 16 16 17 19 19 24 24 21 21 21 21 21 21 21 22 22 22 22 10 4 18 23 23 23 24 24 24 24 25 25 26 30 30 29 29
Standards Number
Price (RM)
Page
MS CISPR MS CISPR 19 : 2000
20
1
MS ISO MS ISO 6570 : 2003
34
30
17
INDEX Subject - MS Number - Page
A Aluminium alloys Stranded conductors for overhead transmission (MS 1143), 3, 25
B Ballasts Fluorescent lamps Energy consumption, performance, (MS 1778:Part1), 18 Energy labeling, (MS 1778:Part2) , 18 Tubular fluorescent lamps Safety requirements (MS 141: Pt. 1), 18 Performance requirements (MS 141 : Pt. 2), 18 A.C. supplied Safety requirements (MS IEC 60928), 15 Performance requirements (MS IEC 60929),15 Discharge lamps (MS IEC 60922), 15 Performance requirements (MS IEC 60923), 15 Batteries Lead acid containers (MS 68),25 Lead acid storage, in automobiles (MS 45), 24 Motorcycles (MS 277),24 Primary cells General (MS 66:Pt 1), 25 Specification sheets (MS 66:Pt 2), 25 Water for lead-acid (MS 994), 25 Bayonet lamp caps - Lampholders & B.C. adaptors (MS 769), 16
C Cable tray systems (MS IEC 61537), 10 Cable trunking and cable ducting systems Electrical installation General requirements (MS 1777:Pt.1),10 Mounting on walls or ceilings (MS 1777:Pt.2-1), 4 Slotted cable trunking system for cabinet (MS 1777:Pt.2-3), 4 Service poles (MS 1777:Pt.2-4), 4 Underfloor and flushfloor installations (MS 1777:Pt.2-2), 4 Mercury/sodium vapour (MS 279), 18, 29 Marking codes (MS IEC 60062), 29 Preferred number series (MS 763), 29 Tubular fluorescent & discharge lamp circuits performance (MS IEC 61049), 17 Tubular fluorescent & discharge lamp circuits safety reg. (MS IEC 61048), 19 Carbon steel tubes (MS 1862), 3 Conduit systems, electrical installations General requirement (MS 1534:Pt.1), 9 Rigid conduit systems (MS 1534:Pt.2:Sec.1), 9 Outsides diameters, threads and fittings (MS IEC 60423), 10 Circuit breakers Earth-leakage, - Residual current operated (MS 946), 1 Miniature air-break (MS IEC 60898-1), 12 A.c and d.c operation (MS IEC 60898-2), 13
Subject - MS Number - Page Cold headed (MS 1863), 3 Conductors, Insulated cables (MS 69), 3, 5 Conductors, Insulated cables (MS IEC 60228), 6 Controlgear & switchgear Circuit – breakers (MS IEC 60947-2), 13 Distribution boards (MS 1445:Pt.3), 13 Factory-built assembly (MS 948), 14 PVC insulated cables (MS 137), 5 Switches, disconnectors, switch-disconnectors & fuse combination unit (MS IEC 60947-3), 12, 13, 14 Type – tested & partially type – tested assemblies (MS 1445:Pt 1), 13 Copper & alloys - Wire, for electrical purposes (MS 280), 3 Couplers Household and general purposes General requirement (MS IEC 60320-1), 11 Interconnection for coupler (MS IEC 60320-2-2), 11 Crimp type Cable lugs (MS 1540), 3 Cable links – Copper (MS 1779), 4 Heavy duty – Copper (MS 1838), 4 Current transformers (MS 1202), 23
D Degree of protection, IP code (MS IEC 60529), 2
E Edison screw lampholders (MS IEC 60238), 16 Electric cables Aluminium solid conductors, Insulated cable (MS 434), 6 Calculation, current rating Sheath eddy (MS IEC 60287-1-2), 6 Thermal resistance (MS IEC 60287-2-1), 6 Reduction factors (MS IEC 60287-2-2), 6 Power cable size (MS IEC 60287-3-2), 6 High-voltage, guide and selection (MS IEC 60183), 6 Fire conditions Apparatus (MS IEC 60331-11), 6 Electric data cables (MS IEC 60331-23), 6 Optical fibre cables (MS IEC 60331-25), 7 Procedures and requirements (MS IEC 60331-21), 6 Single vertical (MS IEC 60332-1), 7 Small vertical insulated copper (MS IEC 60332-2), 7 Insulated flexible cords & cables (MS 140), 5 Insulation & sheath, Rubber (MS 276), 5 Cables for voltages of 1 KV (MS IEC 60502-1), 7 Cables (MS IEC 60502-2), 7 Accessories for cables (MS IEC 60502-4), 7 Insulation & sheaths Test methods (MS 1095), 6
35
Index Subject - MS Number - Page -
Mechanical properties (MS IEC 60811-1-1), 7 Thermal ageing methods (MS IEC 60811-1-2), 7 Water absorption tests (MS IEC 60811-1-3), 7 Hot set test (MS IEC 60811-2-1), 7 PVC, cracking test (MS IEC 811-3-1), 7 PVC,thermal stability test (MS IEC 60811-3-2), 8 PE and polypropylene compounds - Environmental cracking (MS IEC 60811-4-1), 8 - Elongation at break (MS IEC 60811-4-2), 8 - Filling compound (MS IEC 60811-5-1), 8 Oversheaths, special protective (MS IEC 60229), 6 Test method Cables, cords and wires (MS IEC 60885-1), 8 Partial discharge tests (MS IEC 60885-2), 8 - Extruded power cables (MS IEC 60885-3), 8 Portable cable reels, for household use (MS 1141), 11 PVC, Insulation & sheath (MS 138), 5 Electric cable and wire Single-core PVC insulated cable Armoured (MS 2101), 4 Non-Armoured (MS 2100), 4 Multi core PVC insulated cable Non-armoured (MS 2102), 4 Armoured (MS 2103), 4 Single core XLPE insulated cable Non-Armoured (MS 2104), 4 Electric conductors Overhead transmission (MS 1142), 3, 25 Electric conduits Rigid PVC Underground telecommunication cables (MS 1034), 9 Steel conduits,bends & couplers (MS 275:Pt.1), 9 Fittings & components (MS 275:Pt.2), 9 Electric control equipment see Controlgear, Switchgear Electric luminaires -
General requirements (MS IEC 60598-1), 19
-
Fixed general purpose (MS IEC 60598-2-1), 19-
-
Particular requirements Aquarium luminaries (MS IEC 60598-2-11), 20 Flood lights (MS IEC 60598-2-5), 20 Luminaires with built-in transformers for filament lamps (MS IEC 60598-2-6), 20 Limited surface temperatures (MS IEC 60598-2-24), 20 Portable luminaires for garden use (MS IEC 60598-2-7), 20 Portable luminaries for children (MS IEC 60598-2-10), 20 Handlamps (MS IEC 60598-2-8), 20 Luminaires for stage lighting, tv and film studios (MS IEC 60598-2-17), 20 Air-handling luminaires (safety requirements) (MS IEC 60598-2-19), 20 Extra low voltage lighting systems for filament lamps (MS IEC 60598-2-23), 20 Road and street lighting (MS IEC 60598-2-3), 20 Electrical accessories PRCDs (MS IEC 61540), 4 Safety (MS 1144), 1, 9 Boxes and enclosures (MS 1873), 10 Connecting boxes and enclosures (MS 1873:Pt.22), 10 Provision for suspensions and means (MS 1873:Pt.21), 13
Subject - MS Number - Page Electrical apparatus – explosive gas atmospheres General requirements (MS IEC 60079-0), 26 Flameproof enclosures “d” (MS IEC 60079-1), 26 Flameproof enclosures “d” (MS IEC 60079-1-1 ), 26 Fieldbus intrinsically safe concept (FISCO) (MS IEC TS 60079-27), 28 Pressurized enclosures “p” (MS IEC 60079-2),26 Ignition temperature (MS IEC 60079-4), 27 Powder filling “q” (MS IEC 60079-5 ), 27 Oil immersion “o” (MS IEC 60079-6), 27 Increased safety “e” (MS IEC 60079-7), 27 Classification of hazardous areas (MS IEC 60079-10), 27 Intrinsic safety “l” (MS IEC 60079-11), 27 Hazardous areas (other than mines) (MS IEC 600791 4), 2 7 Type of protection “n” (MS IEC 60079-15), 27 Artificial ventilation for the protection of analysers houses (MS 1591), 26 Inspection & maintenance (MS IEC 60079-17), 27 Encapsulation “m” (MS IEC 60079-18), 27 Repair and overhaul, explosives atmospheres (MS IEC 60079-19), 27 Data for flammable gases & vapours (MS 1592), 26 Electrical household appliances Battery chargers (MS IEC 60335-2-29), 24 Circuit breakers for a.c operation (MS IEC 60898-1), 12 Circuit-breakers for a.c and d.c (MS IEC 60898-2), 13 Heating liquids (MS IEC 60335-2-15), 25 Rice cooker (MS 472:Pt.2:Sec.2.9), 1 Rolling shutters, awnings, blinds (MS EC 60335-2-97) 9 Water heaters (MS 472:Pt.3:Sec.3.1), 1 Garage doors (MS IEC 60335-2-95), 9 Special installations or location- swimming pools (MS IEC 60364-7-702), 1 Electrical installations of building - Guide (MS 1936), 1 Electrical installation – conduit systems Particular requirements Pliable conduit systems (MS 1534:Pt.2:Sec.2), 9 Flexible conduit systems (MS 1534:Pt.2:Sec.3), 9 Conduit systems buried underground (MS 1534:Pt.2:Sec.4), 10 Electric plugs - Fuse links (MS 1428), 12 13A, Rewirable & non-rewirable (MS 589:Pt.1), 10 13A, Switched & unswitched socket (MS 589:Pt.2), 10 13A, Fused connection units, switched & unswitched (MS 589:Pt.4), 11 13A, Adaptors (MS 589:Pt.3), 11 15A, plugs and socket-outlets (MS 1577), 11 Flat non-rewirable 2-pole, 2.5A, 250V (MS 1578), 11 Electric power generation Private, Electrical safety code (MS 556), 26 Electric power systems Extra low voltage, For indoor use (MS 860:Pt.1), 1 Electric power transmission Voltages for AC systems (MS 406), 1 Electric shocks-Protection, Construction, Electrical equipment Climatic conditions (MS 477), 28 Electric switches see Switches Electric wires - Wrought aluminium (MS 435), 4 Electrical insulating materials - Classification (MS 938), 3 Electrical measuring instruments Direct acting indicating (MS 925), 26 Maximum demand indicators (MS 944), 1
36
Index Subject - MS Number - Page Electrical plugs – 13A plugs, socket-outlets, adaptors and connection units. Part: 4: Switches and unswitched (MS 589: Pt4), 11 Electrical plugs, flat non-rewirable two-pole plugs, 2.5 A, 250V (MS 1578), 11 Electricity generating sets - Portable (MS 1403), 22 Electricity supply meters Class 0.5, 1 and 2 single-phase and polyphase (MS 859:Pt.1), 8 3 var-hour meters (MS 859:Pt.2), 8 Class 1, Electro-mechanical (MS 859:Pt.3), 9 Electromagnetic compatibility Limits Voltage fluctuations & flicker (MS IEC 61000-3-5), 2 Harmonic currents (MS IEC 61000-3-12), 28 Testing & measurement Power frequency magnetic (MS IEC 61000-4-8), 2 Electrostatic discharge (MS IEC 61000-4-2), 2 Surge immunity test (MS IEC 61000-4-5), 2 Radio frequency (RF) (MS IEC 61000-4-6), 3 Immunity test (MS IEC 61000-4-16), 2 Oscillatory waves (MS IEC 61000-4-12), 2 Oscillatory magnetic(MS IEC 61000-4-10), 2 Radiated, RF, (MS IEC 61000-4-3), 2 Electrical fast transient (MS IEC 61000-4-4), 2 Emission standard for residential, commercial & light-industrial environment (MS IEC 61000-6-3), 3 Emission standard for industrial environments (MS IEC 61000-6-4), 3 Immunity for residential, commercial & light-industrial environment (MS IEC 61000-6-1), 3 Electrotechnical vocabulary: Electrical apparatus for explosive atmospheres (MS IEC 60050-426), 1 Electromagnetism (MS 1487), 1 Electric luminaires Detail requirements Electric handlamps (MS IEC 60598-2-8), 20 Flood lights (MS IEC 60598-2-5), 19 Fixed general purpose (MS IEC 60598-2-1), 19 Lighting chains (MS IEC 60598-2-20), 20 Portable luminaires (MS IEC 60598-2-4), 19 Road street lighting (MS IEC 60598-2-3), 19 Recessed luminaires (MS IEC 60598-2-2), 20 Swimming pools (MS IEC 60598-2-18), 20 Photo and film luminaires (MS IEC 60598-2-9), 15 Hospitals and health care (MS IEC 60598-2-25), 20 Emergency lighting Luminaires (MS 619:Part 2-22), 16 General requirements (MS IEC 60598-1), 19 Portable child – appealing (MS IEC 60598-2-10), 20 Particular requirements Built-in transformers (MS IEC 60598-2-6), 20 Garden use (MS IEC 60598-2-7), 20 Stage lighting, tv and film studios (MS IEC 60598-2-17), 20 Air-handling luminaires (safety requirements) (MS IEC 60598-2-19), 20 Extra low voltage (MS IEC 60598-2-23), 20 Enclosures Degrees of protection (IP code) (MS IEC 60529), 2 Explosive gas atmospheres, Electrical apparatus General requirements (MS IEC 60079-0), 26
Subject - MS Number - Page -
-
Construction, test and marking Group II Zone 0 (MS IEC 60079-26), 28 Flameproof enclosures “d” (MS IEC 60079-1), 26 Flameproof enclosures “d” (MS IEC 60079-1-1), 26 Fieldbus intrinsically safe concept (FISCO) (MS IEC TS 60079-27), 28 Pressurized enclosures “p” (MS IEC 60079-2), 26 Ignition temperature (MS IEC 60079-4), 27 Intrinsically safe systems (MS IEC 60079-25), 27 Powder filling “q” (MS IEC 60079-5), 27 Oil immersion “o” (MS IEC 60079-6), 27 Increased safety “e” (MS IEC 60079-7), 27 Classification - hazardous areas(MS IEC 60079-10), 27 Intrinsic safety “l” (MS IEC 60079-11), 27 Installations in hazardous areas (MS IEC 60079-14), 27 Type of protection “n” (MS IEC 60079-15), 27 Artificial ventilation (MS 1591), 26 Inspection & maintenance (MS IEC 60079-17), 27 Encapsulation “m” (MS IEC 60079-18), 27 Repair and overhaul, explosives atmospheres (MS IEC 60079-19), 27 Data for flammable gases & vapours (MS 1592), 26 Classification of mixtures of gases or vapour (MS 1712), 26 Construction and use of rooms, pressurisation (MS 1713), 26
F Filament lamps – Tungsten Domestic & general lighting (MS IEC 60064), 17 D.C or A.C supplied, convertors General requirements (MS IEC 61046), 16 Performance requirements (MS IEC 61047), 16 Fluorescent lamps Glow – Starters (MS IEC 60155), 16 General lighting service (MS IEC 60188), 18 Double-capped Safety (MS IEC 61195), 19 Performance specifications (MS IEC 60081), 18 Single-capped Safety (MS IEC 61199), 19 Performance (MS IEC 60901), 20 Tubular, performance (MS IEC 60925), 21 Fuses, Low-voltage General requirements (MS IEC 60269-1), 12 Unskilled persons - (MS 1586:Pt.3), 12 Section 1 to IV (MS IEC 60269-3-1), 12 Fuses - authorized persons (MS IEC 60269-2), 12 Standardized fuses (MS IEC 60269-2-1), 12 Fuse-links, semiconductor devices (MS IEC 60269-4), 12 Standardized fuse-links (MS IEC 60269-4-1), 12
G Galvanised steel wire Aluminium conductors (MS 1238), 5 Armouring submarines cables (MS 1240), 5 Low carbon for armouring cables (MS 1239), 5 Strand (MS 1237), 5
37
Index Subject - MS Number - Page
H Heat test source lamps (MS IEC 60634), 21 High – Pressure vapour lamps (MS IEC 60188), 18 High-voltage switchgear and controlgear AC circuit-breakers (MS 1840), 14 AC metal-enclosed (MS 1782), 14 Common specifications (MS 1781), 14
Subject - MS Number - Page -
AC semiconductor (MS IEC 60947-4-2), 14 Control circuit devices and switching elements Electromechanical circuit devices (MS IEC 609475-1), 12, 15 Proximity switches (MS IEC 60947-5-2), 12, 15
-
Assemblies Assemblies, type-tested and partially type-tested (MS IEC 60439-1), 14 Busbar trunking systems (MS IEC 60439-2), 14 Unskilled persons, Distribution boards (MS IEC 60439-3), 14 Construction sites (MS IEC 60439-4), 14 Cables distribution cabinets (MS IEC 60439-5), 14
I Incandescent lamps, Tungsten Filament lamps (MS IEC 60432-1), 17 Halogen lamps (MS IEC 60432-2), 17 INon-vehicle (MS IEC 60432-3), 18 Insulated cables PVC insulated, Non armoured (MS 136), 5 PVC, Electricity supply (MS 274), 5 Rubber insulated power & lighting cables (MS 278), 6
L Lamp cap Measurement of temperature (MS IEC 60360), 16 Lamp caps and holders Gauges Guidelines and general information (MS IEC 60061-4), 16 Lamp holders Requirements & test (MS IEC 60838:Part 1), 17 Lamp holder S14 (MS IEC 60838-2-1), 17 Tubular fluorescent & starter holders (MS IEC 60400), 17 Barrel thread, shade holder ring (MS IEC 60399), 15 Lamps Auxiliaries, Performance (MS IEC 60927), 18 Safety requirements (MS IEC 60926), 16 Incandescent, maximum lamp (MS IEC 60630), 18 Miscellaneous (MS IEC 61549), 18 Tungsten halogen (MS IEC 60357), 17 Ultraviolet, UV-radiation (MS IEC 61228), 16 Sodium vapour, low pressure (MS IEC 60192), 21 Controlgear Safety requirements (MS IEC 61347-1), 21 Starting devices (MS IEC 61347-2-1), 21 Electronic convertors (MS IEC 61347-2-2), 21 Electronic ballast (MS IEC 61347-2-3), 21 General lighting (MS IEC 61347-2-4), 21 Public transport lighting (MS IEC 61347-2-5), 21 Aircraft lighting (MS IEC 61347-2-6), 21 Emergency lighting (MS IEC 61347-2-7), 22 Fluorescent lamps (MS IEC 61347-2-8), 22 Discharge lamps (MS IEC 61347-2-9), 22 Invertors and convertors (MS IEC 61347-2-10), 22 Lead acid batteries Containers (MS 68), 25 Low-voltage power supply Electromagnetic compatibility (EMC) (MS IEC 61204-3), 24 Low-voltage switchgear and controlgear General rules (MS IEC 60947-1), 14 Contactors and motor-starters Electromechanical (MS IEC 60947-4-1), 14
LPG see Liquefied petroleum gas Luminaires – Electrical supply track systems (MS IEC 60570), 18 Mixed supply system – Classes I and III (MS IEC 60570-2-1), 19
M Maximum lamp outlines, General (MS IEC 61126), 16 Metal halide lamps (MS IEC 61167), 17 Microwave ovens – Measurements of radiation (MS CISPR 19), 1 Miniatures lamps (MS IEC 60983), 15
N Natural gas Liquid content (MS ISO 6570), 17
P Polymers Cable insulation & sheaths, Test methods (MS 1095), 6 Portable cable reels (MS 1141), 11 Power supply, low voltage, performance and safety requirements (MS IEC 61204), 24 Power transformers General (MS IEC 60076-1), 23 Insulation level (MS IEC 60076-3), 23 Temperature rise (MS IEC 60076-2), 23 Lightning and switching impulse, guide (MS IEC 60076-4), 23 Short circuit (MS IEC 60076-5), 23 Application guide (MS IEC 60076-8), 23 Sound level (MS IEC 60076-10), 23 Reactors General requirements (MS IEC 61558-1), 23 Separating transformers (MS IEC 61558-2-1), 23 Control transformers (MS IEC 61558-2-2), 23 Ignition transformers for gas & oil burners (MS IEC 61558-2-3), 24 Isolating transformers (MS IEC 61558-2-4), 24 Shaver transformers and supply units (MS IEC 61558-2-5), 24 Safety isolating transformers (MS IEC 61558-2-6), 24 Protective device - residual current operated (MS 946), 1
38
Index Subject - MS Number - Page
Subject - MS Number - Page
Residual current operated circuit-breaker General rules (MS IEC 61008-1), 13 Independent of line voltage (MS IEC 61008-2-1), 13 Dependent on line voltage (MS IEC 61008-2-2), 13 Integral overcurrent protection (MS IEC 61009-1), 13 RCBO’s functionally independent of line voltage (MS IEC 61009-2-1), 13 RCBO’s functionally dependent on line voltage (MS IEC 61009-2-2), 13 Road vehicles Filament lamps, dimensional and requirement (MS IEC 60809), 16 Lamps, performance requirements (MS IEC 60810), 16 Rotating electrical machines (MS IEC 60034-2), 22 Cylindrical rotor synchronous machines (MS IEC 60034-3), 22 Protective enclosures (IP code) (MS IEC 60034-5), 22 Methods of cooling (IC code) (MS IEC 60034-6), 22 Mounting arrangement (IM code) (MS IEC 60034-7), 22 Terminal markings (MS IEC 60034-8), 22 Insulated cables, Power & lighting (MS 278), 6 Insulation & sheath, Electric cables (MS 276), 5
Switchgear Factory-built assembly (MS 948), 14 PVC insulated cables (MS 137), 5 Switchgear & Controlgear Circuit – Breakers (MS IEC 60947-2), 13 Switches, disconnectors, switch-disconnectors (MS IEC 60947-3), 12, 13, 14 Contactors & motor-starters Electromechanical contactors (MS IEC 60947-4-1), 14 AC semiconductor motor (MS IEC 60947-4-2), 14 General rules (MS IEC 60947-1), 14 Control circuit devices and switching elements (MS IEC 60947-5-2), 12, 15 Electromechaniical control circuit devices (MS IEC 60947-5-1), 12, 15 High-voltage Alternating –current circuit breakers (MS 1840), 14 Standards (MS 1781), 14 Low-voltage, assemblies Assemblies, type-tested and partially type-tested (MS IEC 60439-1), 14 Busbar trunking systems (MS IEC 60439-2), 14 Unskilled persons, Distribution boards (MS IEC 60439-3), 14 Construction sites (MS IEC 60439-4), 14 Cables distribution cabinets (MS IEC 60439-5), 14
S
Switchgear & Controlgear assemblies – type – Tested assemblies (MS 1445:Pt.1), 13
R
Self-ballasted lamps – Performance (MS IEC 60969), 19 Safety requirements (MS IEC 60968), 18 Signs - “Keluar” signs, Internally illuminated (MS 983), 19 Socket-outlets, portable 2 pin (MS 1579), 11 Stabilized power supply Reference levels & measurement of conducted electromagnetic interference (MS IEC 60478-3), 24 Specifying rating & performance ((MS IEC 60478-2), 24 Terms and definitions (MS IEC 60478-1), 24 Test other than radio – frequency interference (MS IEC 60478-4), 24 Steel-wire rods High carbon (MS 1093), 5 Low carbon (MS 1092), 5 Steel-wire ropes Rounded steel for, (MS 550), 4 Stranded conductors Aluminium alloy, overhead transmission (MS 1143), 3, 25 Surge protective devices, low-voltage power distribution Requirements and tests (MS IEC 61643-1), 25 Gas discharge tubes (GDT) (MS IEC 61643-311), 30 Avalanche breakdown diode (MS IEC 61643-321), 30 Selection, application principles (MS IEC 61643-12), 25 Performance requirements (MS IEC 61643-21), 26 Metal oxide varistors (MOV) (MS IEC 61643-331), 29 Thyristor surge suppressors (MS IEC 61643-341), 29 Switches A.C. switches, of over 1 kV rated voltage ((MS 1039), 11 Air-break, for up to 1000 a.c. or 1200 d.c. (MS 590), 30 Switches, for household General requirements (MS IEC 60669-1), 11 Electronics switches (MS IEC 60669-2-1), 11 Remote control switches (RCS) (MS IEC 60669-2-2), 11 Time-delay switches (TDS) (MS IEC 60669-2-3), 12
T Transformers Current (MS 935), 23 Not exceeding 1kVa rating (MS 768), 23 Safety isolating transformers (MS 1700), 23 Tubular discharge lamps (MS IEC 61050), 19 Tungsten filament lamps Performance requirements (MS IEC 60064), 17 Tungsten halogen lamps Non-vehicle (MS IEC 60357), 17 Measuring temperature, quartz (MS IEC 60682), 20
V Voltages (MS IEC 60038), 1
W Wire ropes Fibre components, Test methods (MS 528), 4 Cranes, excavators & general engineering (MS 551), 4 Ropes 7 mm & smaller (MS 796), 5 Stranded, Impregnating compounds & lubricants (MS 529), 4 Stranded, requirements (MS 754), 4 Wiring accessories, General requirements (MS 1144), 1, 9
39
