User's guide
SDMO Contr ol u unit KERYS T T ACTIL -- S S 9 9000
V 1.05 (29/06/06)
33502015901_2_1
1. MICS Kerys ............................................................... ............................................................ ........................................................... .... 2 1.1. Aim and structure ......................................................... ............................................................... ............................................ 2 2. Using the interface ........................................................... ............................................................... ...................................................... 2 2.1. Presentation of the keypad............................................. .............................................................. ............................................ 2 2.1.1 The display ................................................... ............................................................ ........................................................... .... 3 2.1.2 The alphanumeric keys............................................................ .............................................................. .................................. 3 2.1.3 The generating set operational keys .............................................................. ............................................................ .............. 4 2.1.4 The navigation keys .......................................................... .......................................................... ............................................ 5 2.1.5 The signalling control keys ................................................................ ............................................................. ........................ 5 2.2. Interface ergonomics ...................................................... ............................................................. ............................................ 5 2.2.1 Description of the screens .................................................................. ............................................................. ........................ 6 2.2.2 The home screen ......................................................... ................................................................ ............................................ 6 2.2.3 Navigation screens ....................................................... ............................................................... ............................................ 7 2.2.4 Operating and configuration screens........................................................... screens ........................................................... .............................................................. .............. 8 2.2.4.1. Upper band indicators ....................................................... ................................................................. ........................ 8 2.2.4.2. Upper band commands............................ ........................................................... ........................................................ 9 2.2.4.3. Lower band functions.......................................................... functions .......................................................... ............................................................... ........................ 9 2.2.5 The dialogue boxes....................................................................... ................................................................... ........................ 9 2.2.5.1. Confirming an entry in a main screen ............................................................... ......................................................... 9 2.2.5.2. Entering text ........................................................... .................................................................. ................................ 10 2.2.5.3. Entering numerical values .......................................................... ................................................................ .............. 10 2.2.5.4. Selecting from a list.............................. ................................................................ .................................................... 11 2.2.6 Saving modifications..................................... ........................................................... ............................................................. 11 3. Using menus ............................................................. ............................................................. ........................................................... .. 12 3.1. Layout of the menus ................................................... ................................................................. .......................................... 12 3.1.1 Generating set operating modes ............................................................... .............................................................. ............... 13 3.1.2 Menu Menu layout according to operating mode................................................................ mode..... ........................................................... ............................................................ 18 3.2. Operating menus................................................................... ................................................................. ................................ 19 3.2.1 Driving ........................................................ ............................................................. ........................................................... .. 19 3.2.2 Function keys ............................................................... ............................................................... .......................................... 19 3.2.3 Synchronisation column..................................................................... column ..................................................................... ........................................................... ........................ 19 3.2.4 Power plant measurements summary ........................................................ ................................................................ ............ 19 3.2.5 Measurements ........................................................ ........................................................... .................................................... 19 3.2.5.1. Generating set electrical measurements measurements ................................................................ ................................................... 19 3.2.5.2. BUSBAR/grid(s) BUSBAR/grid(s) electrical measurements measurements ............................................................. .................................................. 19 3.2.5.3. Mechanical measurements .............................................................. ............................................................ ............. 19 3.2.5.4. Generating set harmonic measurements.................. ..................................................................... ............................ 19 3.2.5.5. BUSBAR/grid(S) BUSBAR/grid(S) harmonic measurements.......................................................... .................................................... 19 3.2.5.6. Rotating field measurements......................................................... measurements ......................................................... .............................................................. ............. 19 3.2.5.7. Customised display of analogue values.......... ................................................................ .......................................... 19 3.2.6 Alarms and faults .......................................................... ............................................................. ........................................... 19 3.2.6.1. Help ............................................................ ............................................................... ............................................... 19 3.2.7 User settings ........................................................ .............................................................. .................................................... 19 3.2.7.1. Set points ............................................................. ........................................................... .......................................... 19 3.2.7.2. Power thresholds ..................................................... ................................................................. ................................ 19 3.2.7.3. Wattmetric control / General parameters.................................................................................. ................................ 19 3.2.7.4. Wattmetric control / Thresholds............ ................................................................ ................................................... 19 3.2.7.5. Generating set priorities ................................................................ ............................................................. .............. 19 3.2.7.6. User parameters (1/2) ................................................................ ................................................................. .............. 19 3.2.7.7. User parameters (2/2) ................................................................ ................................................................. .............. 19 3.3. Regional parameters....................................................... parameters ....................................................... ...................................................................... ................................. 19 4. Generating set starting modes ............................................................... .............................................................. ................................ 19 4.1. General information..................................................................................... ........................................................... ............... 19 4.2. Prerequisites ............................................................... ................................................................ ........................................... 19 4.3. Manual starting................. ................................................................ ............................................................. ........................ 19 4.4. Starting using the no load test function ................................................................. ........................................................... ..... 19 4.5. Starting using the load test function ................................................................ ................................................................. ..... 19 4.6. Starting in automatic mode................................... ............................................................ ..................................................... 19 5. Definitions ........................................................... .................................................................. ........................................................... .. 19 5.1. Glossary...................................................... ........................................................... .............................................................. .. 19
1/62
33502015901_2_1
1. MICS Kerys 1.1. Aim and structure The MICS KERYS system comprises a range of electronic modules which are to be used for control and command operations, setting and protecting generating sets which stand alone or feature as part of a power plant. The system includes the following modules: industrial programmable automatic control module (A.P.I.) All or nothing logical inputs and outputs module Analogue inputs and outputs module temperature acquisition module electrical safety module Man-Machine Interface Module adjustment module An industrial programmable automatic control module and a Man-Machine Interface module form the basic configuration of the system.
2. Using the interface 2.1. Presentation of the keypad Generating set control keys
Alphanumeric keypad.
Signalling control keys
Navigation keys
Back-lit display with touch panel Man Machine Interface operation indicator LED (flashing)
2/62
33502015901_2_1
2.1.1 The display The display has the following specifications: 7-inch colour TFT display, 16/9, 65536 colours dimensions: 154 mm x 86 mm neon backlighting 480 x 234 resolution touch panel (8 columns x 8 rows)
2.1.2 The alphanumeric keys Pressing these keys successively allows the facial values to be entered. The characters entered appear in the order they were typed on the keypad.
3/62
33502015901_2_1
2.1.3 The generating set operational keys 1 2 3
4
8 9 10 11 12
13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
7 6 5
Manual mode selection. The illuminated led indicates that the mode is active Selecting stop mode. The illuminated led indicates that the mode is active Automatic mode selection The illuminated led indicates that the mode is active Test in progress In automatic mode: test sequence control In manual mode: starting and stopping the motor Generating set circuit breaker opening control Open generating set circuit breaker Grid circuit breaker opening control Open grid circuit breaker Grid circuit breaker closing control Closed grid circuit breaker Grid voltage status Grid circuit breaker closing control Closed generating set circuit breaker Generating set voltage status
If test is requested a screen is b rought up with the choice of a test under load or test off load.
4/62
33502015901_2_1
2.1.4 The navigation keys These keys are described in the section on "Interface Ergonomics".
2.1.5 The signalling control keys The
key is used to clear any faults
The
keys stops the buzzer
The
key controls the keypad indicator test.
2.2. Interface ergonomics The KERYS interface screen has a touch panel enabling various menus and commands to be accessed. The active zones on the screen are indicated by rectangles. The extended zones indicate the control keys, the recessed zones indicate the indicators. However, in some cases, the indicators allow access to menus listing general information; for example, pressing the fault indicator displays the list of alarms and faults. When an indicator is active, pressing one of these indicators displays the list of faults and alarms 15/10/02
19:10 :00
-1Electrical archives
GS 1
Event archives
-2Mechanical archives
Control key
Au to
Faults
Al arms
-3 – Event metering
Key selected.
These keys only need to be touched briefly. If they are pressed for too long and there is a key in the same position on the new screen, the corresponding command will be performed. Warning
5/62
33502015901_2_1
It is also possible to navigate through the menus using the keypad. Scroll up
Move up one level or quit if in dialogue box
Scroll left
Scroll right
Confirms the function of the selected key
Scroll down
Lastly, it is possible to access a menu directly by pressing the corresponding number key.
2.2.1 Description of the screens There are three types: the home screen the navigation screens the operation and configuration screens
2.2.2 The home screen This screen is the entry point to the system. It enables the main functions of the navigation t o be accessed.
15/10/03
19:10 :00
GS 1
Home
Auto
Faults
-1Operation
-6System -2Fault finding -3Archiving/Metering
6/62
Alarms
-5Configuration -4Maintenance
33502015901_2_1
2.2.3 Navigation screens These screens enable the various sub-menus to be accessed. Upper level
15/10/03
19:10 :00
Active menu title
GS 1
Operation
Lower levels
Auto
Faults
Alarms
-0Welcome
-1Operation -2Function keys
-7User adjustments -6Alarms & Faults
-4Central measurements summary
-5Measurements
When a key is selected the lower level sub-menu appears if available or the allocated operation screen. A sub-menu can also be accessed by pressing the corresponding numbered key.
7/62
33502015901_2_1
2.2.4 Operating and configuration screens These screens bring up the information and commands relating to the active menu. They are divided into three zones: an upper band present on all types of screens the centre section in which the specific information relating to the selected menu appears a lower band Upper band
15/10/03
19:10 :00
GS 1
Centre section
Event archives
Au to
Faults
Al arms
-3 – Central measurements summary
-1Electrical archives
Lower band
2.2.4.1.
Upper band indicators Indication of alarm on the generating set concerned (flashing)
System date System time Number of generating set with which the man machine interface is in dialogue with
Indication of fault on the generating set concerned (flashing) Indication of the operating mode of the generating set concerned
Name of the active screen
15/10/02
8/62
19:10 :00
GS 1
Welcome
Au to
Faults
Al arms
33502015901_2_1
2.2.4.2.
Upper band commands Access to the Alarms & Faults screen
Access to the regional parameters screen Access to the regional parameters screen
Access to the Alarms & Faults screen
Access to the operation screen
19:10:00
Welcome GS 1
15/10/03
If in power plant configuration, open a dialogue box enabling the generating set which you want to connect to be selected
2.2.4.3.
Au to
Faults
Al arms
st
1 action: access to the home screen nd 2 action: return to previously selected menu
Lower band functions Return to the navigation menu Pressing one or more of the short cut keys directs you to the functions linked to the active screen
Return to previous active operation screen
-3 – Central measurements summary
-1Function keys
2.2.5 The dialogue boxes To make it easier to enter information, there are special screens called "dialogue boxes" which appear if required.
2.2.5.1.
Confirming an entry in a main screen
When a value in the main menu has been modified the following dialogue box appears: Validation Validation of data entered Confirm
Esc.
The "Confirm" key saves the change, the "Esc." escape key cancels the change.
9/62
33502015901_2_1
2.2.5.2.
Entering text Name of the function modified
Text to be modified or created.
Inserts a space to the left of the cursor Title configuration CDE AERO Insert Confirm
Copy
Delete title
Paste
Delete a character
Esc.
Deletes the letter highlighted by the cursor Closes the menu without saving the modifications.
Deletes all the text
Saves the modifications and closes the dialogue box Left or right arrows on the keypad are used to move within the text. Characters are entered via alphanumeric keys on the keypad.
2.2.5.3.
Entering numerical values
The dialogue box heading displays the type of value entered,its unit of measurement and the variable concerned. These indications are linked to the type of modified parameter. When present, displays the minimum possible value When present, displays the maximum possible value
Time in 1/10 second (6000) 0<= Confirm
0000
<=9999 Esc.
Closes the dialogue box without saving the modifications Saves the modifications and closes the dialogue box
10/62
33502015901_2_1
2.2.5.4.
Selecting from a list
The box heading indicates the parameter which will be assigned from your selection. List showing possible selections
Arrows enabling the cursor to be moved
Type of fault (6000) Without General Alarm
Confirm
Esc.
Active selection Arrows visible only if the selection numbers do not remain on the screen
2.2.6 Saving modifications After modifying a parameter, the new data is stored in volatile memory, which means that if the power supply is lost any changes will be lost. It is also necessary to transfer these values to permanent memory. This is a "Flash save" operation Following a modification, a red "Perform back-up" indicator light flashes at the top left-hand side of the screen. Pressing this indicator makes one of the following dialogue boxes appear. Save in flash
Confirm.
Esc.
Save in flash
Customer
Factory
Confirm.
Esc.
Pressing "Confirm.", confirms the operation, pressing "Esc.", cancels it. While the data is being saved, a screen indicates that the operation is in progress.
11/62
33502015901_2_1
3. Using menus 3.1. Layout of the menus The diagram below shows the layout of the main menus. -0Welcome
-1-
-2-
Operation
Fault finding
-3Archiving & Metering
- 1.1 -
- 2.1 -
- 3.1 -
Operation
Digital I/O
Events archives
- 1.2 Function keys
- 2.2 -
- 3.2 Electrical archives
Analog variables
- 1.3 Synchro. column
- 2.3 REG & PRO variables
- 1.4 Central unit measure, summary
- 2.4 Curves (Kerys Tactil)
- 1.5 -
- 2.5 -Electrical faults
Measurements
- 1.6 Alarms & faults
- 2.6 -
- 1.7 -
- 2.7 All or nothing personalised display
User adjustments
Help
-4-
-5-
-6-
Maintenance
Configurations
System
- 4.1 Provider
- 5.1 -
- 6.1 -
Equipment
Regional parameters
- 4.2 -
- 5.2 -
- 6.2 -
E-mail
Applications
Identification application
- 4.3 Service intervals
- 5.3 Regulations
- 6.3 -
- 3.4 -
- 4.4 -
- 5.4 -
- 6.4 -
Events metering
Consumables
Safety features
Printing
- 3.5 Mechanical metering
- 4.5 Progress reports
- 3.6 Electrical metering
- 4.6 -
- 6.6 -
Reports
Management of Web access
- 3.3 Mechanical archives
Software versions
- 6.5 Access management
- 6.7 Factory
Only the menu functions on the white background are described in this manual. Warning
12/62
33502015901_2_1
3.1.1 Generating set operating modes The operational modes are as follows: generating set operating alone / without normal / emergency inversion (configurations A612) generating set operating alone / with normal / emergency inversion and alternator circuit breaker (configurations A622) generating set operating alone / generating set coupled to the network (configurations A641 / A642 / A651 / A661) generating set operating as part of power plant / operating without shared normal/emergency switching unit. (configurations A633) generating set operating as part of power plant / operating with shared normal/emergency switching unit. (configurations A634) generating set operating as part of a power plant / operating with shared switching unit (configurationA635) Configuration A612
TC: X/5A 5P5 10VA
Protection card 3Ph+N 5VA Bus CAN no. 3 Standard module
m
ETHERNET Network
Configuration A622
TC: X/5A 5P5 10VA
Protection card
CAN 3 bus 3Ph+N 5VA
Standard module
Power voltage detection
ETHERNET Network
m
13/62
m
33502015901_2_1
Configuration A641
TC: X/5A 0.5 10VA
Control card
3Ph 5VA
CAN 3 bus 3Ph+N 5VA
m
Standard module
ETHERNET Network
m
Configuration A642
TC: X/5A 0.5 10VA
Control card
TC: X/5A 0.5 10VA 3Ph 5VA
CAN 3 bus 3Ph+N 5VA
m
Standard module ETHERNET Network
m
14/62
33502015901_2_1
Configuration A651
TC: X/5A 0.5 10VA
Control card
TC: X/5A 0.5 10VA 3Ph 5VA
CAN 3 bus 3Ph+N 5VA Circuit breaker ALTERNATOR OPTIONAL MANUAL OR AUTOMATIC
Standard module
ETHERNET Network
m
m
Configuration A661
TC: X/5A 0.5 10VA
Control card
TC: X/5A 0.5 10VA 3Ph 5VA
CAN 3 bus 3Ph+N 5VA Circuit breaker Alter nato r OPTIONAL MANUAL OR Auto
ETHERNET Network
m
15/62
Standard module
m
33502015901_2_1
Configuration A633
TC: X/5A 0.5 10VA
TC: X/5A 0.5 10VA
3Ph 5VA
Control card
Control card
Bus CAN REG
3Ph+N 5VA
CAN 3 bus 3Ph+N 5VA
CAN 3 bus
Standard module
m
M
3Ph 5VA
CAN 4 bus M
Standard module
m
ETHERNET Network
ETHERNET Network
Configuration A634 Bus CAN REG
TC: X/5A 0.5 10VA
TC: X/5A 0.5 10VA
Control card
Control card
3Ph+N 5VA
3Ph+N 5VA CAN 3 bus CAN 4 bus
Standard module M
m
M
Standard module
m
ETHERNET Network
3Ph 5VA
Normal/emergency control via each base
16/62
CAN 3 bus
ETHERNET Network
Power voltage detection
3Ph 5VA
m
m
33502015901_2_1
Configuration A635 Bus CAN REG
TC: X/5A 0.5 10VA TC: X/5A 0.5 10VA
Control card
Control card
Control card
3Ph 5VA 3Ph+N 5VA
3Ph+N 5VA CAN 3 bus CAN 4 bus
Standard module M
m
M
Standard module
Standard module
m
ETHERNET Network
3Ph 5VA
Central measurements are requir ed if t here are several grids
17/62
CAN 3 bus
CAN 3 bus
ETHERNET Network
ETHERNET Network
3Ph 5VA
m
m
33502015901_2_1
3.1.2 Menu layout according to operating mode The layout of the menus according to operation mode is as follows: Modes:
Modes:
A612 - A622
A633 - A634 - A635 - A641 - A642 - A651 - A661
-0Home
-1Operation
-0Home
-6System - 1.1 Operation
- 1.2 Function keys
-1Operation - 6.1 Regional parameters
-6System - 1.1 Operation
- 6.1 Regional parameters
- 1.2 Function keys
- 1.3 Synchronisation Column - 1.4 Central measurements summary
- 1.4 Central measurements summary
- 1.5 Measurements
- 1.5 Measurements
- 1.6 Alarms & Faults
- 1.6 Alarms & Faults
- 1.7 User settings
- 1.7 User settings
The description of menus and associated screens refers to the above-mentioned operating modes. If there is no particular information, the menus are considered as being general and applicable to all operating modes defined above. Warning
18/62
33502015901_2_1
3.2. Operating menus The operating menus combine all the menus required for operating the generating set. Operating modes: A633 - A634 - A635
15/10/03
19:10 :00
GS 1
Operation
Auto
Faults
Alarms
-0Welcome
-1Operation -2Function keys
-7User adjustments
-3Synchronisation column
-6Alarms & Faults
-4Central measurements summary
-5Measurements
Operating mode: A612 - A622 - A642
15/10/03
19:10 :00
GS 1
Operation
Auto
Faults
Alarms
-0Welcome
-1Operation -2Function keys
-7User adjustments -6Alarms & Faults -5Measurements
19/62
33502015901_2_1
Operating mode: A641 - A651 - A661
15/10/03
19:10 :00
GS 1
Operation
Auto
Faults
Alarms
-0Welcome
-1Operation -2Function keys
-7User adjustments
-3Synchronisation column
-6Alarms & Faults -5Measurements
15/10/2003
20/62
00 : 00 :00
GS 1
Operation
Stop
Faults
Alarm
33502015901_2_1
3.2.1 Driving This general screen displays all the main electrical parameters of the generating set. It is the general operating and monitoring screen for the generating set. This screen can also be displayed by pressing indicator displaying the operation mode of the g enerating set. The frequency, U23 voltage, active and reactive power indicators, can be displayed in analog or digital form. Switching from one mode to another is performed by pressing the desired indicator.
15/10/2003
00 : 00 :00
GS 1
Operation
I1(A)
2701
Manu
P.F
Faults
Alarms
0.9 L
Q(kVAr) Speed (rpm)
1505
Operating time:
10:05
+Speed -1Function keys
-Speed
+U
-2-
Synchronisation column
Motor rotation speed control
765 -U
-3Power plant measurements summary
Alternator voltage control Generating set output position indicator
The speed and voltage adjustment buttons are only present on coupled applications in manual mode. Warning
21/62
33502015901_2_1
3.2.2 Function keys Pressing one of these keys, activates a particular function programmed in production, according to the generating set user configuration selected by the user. This menu has the additional commands required for operating the g enerating set. The most frequently used commands are: Restore mains in EJP Forced global operation Close emergency circuit breaker
Confirm mains return Inhibit safety features Open emergency circuit breaker
Normal maintenance Open emergency circuit breaker Close normal emergency circuit breaker
It is possible to change the text describing the function of the key. The procedure is as follows: press the"title configuration " key, select the key concerned and the text box will appear.
Operating modes: A641 - A642 - A651 - A661 Active key
Key active and selected
15/10/2003
00 :00 :00
GS 1
U23(V)
0
I 1(A)
TCH FCT 1 (3710)
Function keys
0
P.F.
Stop
Faults
Alarms
0L
F (Hz)
0
Status messages
TCH FCT 5 (3714)
RESTORE MAINS POWER
TCH FCT 6 (3715)
TCH FCT 3 (3712)
TCH FCT 7 (3716)
TCH FCT 4 (3713)
Operating time
0: 00
TCH FCT 8 (3717)
Title configuration -1Synchronisation column
22/62
-3Measurements
33502015901_2_1
Operating modes: A633 - A634 - A635 Active key
Key active and selected
15/10/2003
00 :00 :00
GS 1
U23(V)
0
I 1(A)
TCH FCT 1 (3710)
Function keys
0
P.F.
Stop
Faults
Alarms
0L
F (Hz)
0
Status messages
TCH FCT 5 (3714)
TCH FCT 2 (3711)
TCH FCT 6 (3715)
TCH FCT 3 (3712)
TCH FCT 7 (3716)
TCH FCT 4 (3713)
Operating time
0: 00
-2Central measurements summary
-3Measurements
TCH FCT 8 (3717)
Title configuration -1Synchronisation column
23/62
33502015901_2_1
Operating modes: A612 - A622 Active key
Key active and selected
15/10/2003
00 :00 :00
GS 1
U23(V)
0
I 1(A)
TCH FCT 1 (3710)
Function keys
0
P.F.
Stop
Faults
Alarms
0L
F (Hz)
0
Status messages
TCH FCT 5 (3714)
TCH FCT 2 (3711)
TCH FCT 6 (3715)
TCH FCT 3 (3712)
TCH FCT 7 (3716)
TCH FCT 4 (3713)
Operating time
0: 00
TCH FCT 8 (3717)
Title configuration -3Measurements
24/62
33502015901_2_1
3.2.3 Synchronisation column This screen allows the user to view the synchronisation in progress of two sources (frequency, voltage and phase deviations). Operating modes: A633 - A634 - A635 Indication of frequency deviation
15/10/2003
00: 00: 00
Indication of voltage deviation
GS 1
Synchronisation column
Manu
Faults
Alarms
0° Delta F
Delta V 20°
-
20°
+
-
+
0.00Hz
0% TOP COUPLAGE
+ Speed
- Speed
+V
+
-V
-
Synchro in progress -1Function keys
-2Central unit measure. summary
-3Measurements Graph showing voltage deviation
Graph showing frequency deviation
The TOP COUPLING button, the + Speed and – Speed controls, and +V –V only appear in Manual mode Warning
25/62
33502015901_2_1
Operating modes: A641 - A 642 - A651 - A661
Indication of fre uenc deviation
15/10/2003
00: 00: 00
Indication of voltage deviation
GS 1
Synchronisation column
Manu
Faults
Alarms
0° Delta F
Delta V 20°
-
20°
+
-
+
0.00Hz
0% TOP COUPLAGE
+ Speed
- Speed
+V
+
-V
-
Synchro in progress -1Function keys
-3Measurements Graph showing voltage deviation
Graph showing frequency deviation
The TOP COUPLING button, the + Speed and – Speed controls, and +V –V only appear in Manual mode Warning
26/62
33502015901_2_1
3.2.4 Power plant measurements summary This screen can only be accessed in "power plant" operation. It displays electrical measurement values for each generating set in the power plant as well as power plant outputs. Operating modes: A633 - A634 - A635
15/10/2003 00 : 00: 00 Choice of sets to display
GS 1 P(kW)
Central unit measure. summary
Q(kVAR)
Stop
Faults
Alarm
S(kVA)
I1(A)
P.F.
Gen set no.
01
0
0
0
0
0L
Gen set no.
02
0
0
0
0
0L
Gen set no.
03
0
0
0
0
0L
14 Kerys Tactyl
14
Control unit
-1Function keys
27/62
0
0
0
F(Hz)
0
U23(V)
-2Synchro. column
Kerys
0
-3Measurements
33502015901_2_1
3.2.5 Measurements This command brings up a sub-menu from which the following measurements can be taken: Operating modes: A633 - A634 - A635 - A641 - A642 - A651 - A661 15/10/03
19:10:00
Genset
Measurements
Auto
Faults
Alarms
-0Operation -1Electrical measurements -2BUSBAR/Grid(s) elect. measurements
-7Customised analogue display
-3Mechanical measurements.
-6Rotating fields
-4Harmonics
-5Grid(s) harmonics
Operating modes: A612 - A622 15/10/03
19:10:00
GS 1
Measurements
Auto
Faults
Alarms
-0Operation
-1Electrical measurements -2BUSBAR/Grid(s) elect. measurements
-3Mechanical measurements.
28/62
33502015901_2_1
3.2.5.1.
Generating set electrical measurements
This screen displays all the electrical measurements of the generating set: starter battery voltage (Vbat) voltages between phases expressed in Volts (V12, V23 and V31) phase currents expressed in Amps (I12, I23 and I31) power factor (PF) frequency F expressed in Hertz active power per phase (P1, P2 and P3) expressed in kW total active power (PT1) expressed in kW reactive power per phase (Q1, Q2 and Q3) expressed in kvar total reactive power (QT) expressed in kvar active energy (AE) supplied, expressed in MWh reactive energy (RE) supplied, expressed in Mvar
Operating modes: A633 - A634 - A635 - A641 - A642 - A651 - A661
29/62
33502015901_2_1
Operating modes: A612 - A622
30/62
33502015901_2_1
3.2.5.2.
BUSBAR/grid(s) electrical measurements
This screen enables all the grid electrical measurements to be displayed: the starter battery voltage (Ubat) the voltages between phases expressed in (U12, U23 and U31) the phase currents expressed in Amps (I12, I23 and I31) the power factor (P.F.) the frequency expressed in Hertz the active power by phase (P1, P2 and P3) expressed in kW the total active power (PT1) expressed in kW the reactive power by phase (Q1, Q2 and Q3) expressed in kvar the total reactive power (QT) expressed in kvar
Operating modes: A633 - A634 - A635 - A641 - A642 - A651 - A661
15/10/2003
00 : 00 :00
GS 1
BUSBAR/Grids electrical measurements
Stop
Faults
Alarms
01 U12(V)
0
I1(A)
0
P1(kW)
0
Q1(kVAR)
0
U23(V)
0
I2(A)
0
P2(kW)
0
Q2(kVAR)
0
U31(V)
0
I3(A)
0
P3(kW)
0
Q3(kVAR)
0
P.F.
0L
F (Hz)
0
PT(kW)
0
QT(kVAR)
0
-1Electrical measurements
-2Mechanical measurements
-3Grid(s) harmonics
The grid selection dialogue box is only present if the installation is managing several power supplies. Warning
31/62
33502015901_2_1
Operating mode: A612 - A622
15/10/2003
00 : 00 :00
GS 1
BUSBAR/Grids electrical measurements
Stop
Faults
Alarms
01 U12(V)
0
I1(A)
0
P1(kW)
0
Q1(kVAR)
0
U23(V
0
I2(A)
0
P2(kW)
0
Q2(kVAR)
0
U31(V
0
I3(A)
0
P3(kW)
0
Q3(kVAR)
0
P.F.
0L
F (Hz)
0
PT1(kW)
0
QT(kVAR)
0
-1Electrical measurements
-2Mechanical measurements
The grid selection dialogue box is only present if the installation is managing several power supplies. Warning
32/62
33502015901_2_1
3.2.5.3.
Mechanical measurements
This screen enables the main motor parameter values to be displayed. Operating modes: A633 - A634 - A635 - A641 - A642 - A651 - A661 15/10/2003
00 : 00 :00
Mechanical measurements
GS 1
Stop
Faults
Alarms
Temp. LT coolant(°C)
0.00
Oil pres. (bar)
0.00
Temp. HT Coolant(°C)
0.00
Air intake pres. (bar)
0.00
Air intake Temp.(°C)
0.00
Common rail pres. (bar)
0.00
Fuel temp. (°C)
0.00
Fuel pres. (bar)
0.00
Oil temp. (°C)
0.00 °F display
-1Electrical measurements
-2BUSBAR/grid (s) electrical measurements
Display in PSI -3Harmonics
In this zone, when supplied by the motor regulation system, operational information is supplied
33/62
33502015901_2_1
Operating modes: A612 - A622 15/10/2003
00 : 00 :00
Mechanical measurements
GS 1
Stop
Faults
Alarms
Temp. LT coolant(°C)
0.00
Oil pres. (bar)
0.00
Temp. HT Coolant(°C)
0.00
Air intake pres. (bar)
0.00
Air intake Temp.(°C)
0.00
Common rail pres. (bar)
0.00
Fuel temp. (°C)
0.00
Fuel pres. (bar)
0.00
Oil temp. (°C)
0.00 °F display
-1Electrical measurements
Display in PSI
-2BUSBAR/grid (s) electrical measurements
In this zone, when supplied by the motor regulation system, operational information is supplied
The type of values displayed varies according to the type of motor selected. Warning The “Display in …" keys enables the temperature measurements to be read in degrees Celsius or degrees Fahrenheit and the pressure measurements in bar or in PSI.
34/62
33502015901_2_1
3.2.5.4.
Generating set harmonic measurements
This screen lets the user find out level 3, 5 and 7 harmonic rates on generating set currents and voltages. Operating modes: A633 - A634 - A635 - A641 - A642 - A651 - A661
15/10/2003
00:00:00
GS 1
Genset harmonics
Voltages
Stop
Faults
Alarms
Currents
0%
0%
0% 0%
0%
0%
0%
0%
0% 0%
0%
0%
0%
0%
0% 0%
0%
0%
L1
L2
L3
3 -1 Electrical measurements
3.2.5.5.
5
7
3
-2Mechanical measurements
5
7
-3Grid(s) harmonics
BUSBAR/grid(S) harmonic measurements
This screen displays the emergency Bus bars or grid harmonics. Operating modes: A633 - A634 - A635 - A641 - A642 - A651 - A661
15/10/2003
00 : 00 :00
GS 1
Grid(s) harmonics
Voltages
Stop
Faults
Alarms
Currents
0%
0%
0% 0%
0%
0%
0%
0%
0% 0%
0%
0%
0%
0%
0% 0%
0%
0%
L1
L2
01
L3
3 -1BUSBAR/Grids electrical measurements
35/62
5
7
-2Mechanical measurements
3
5
7
-3Harmonics
33502015901_2_1
3.2.5.6.
Rotating field measurements
This screen enables the direction of rotation for each power supply field to be compared. Operating modes: A633 - A634 - A635 - A641 - A642 - A651 - A661
15/10/2003
00 : 00 :00
GS 1
Rotating fields
Grid(s)
01
Stop
Faults
Alarm
Generating set(s)
R
S
T
R
S
T
A
B
C
A
B
C
Phase sequence Inverse -1BUSBAR/grid (s) electrical measurements
Phase sequence normal
-2Mechanical measurements
Inverse
normal
-3Harmonics
The data supplied is directly linked to the correct voltage connections on the I.A.S. inputs The user must always check that the indication is correct. Warning
36/62
33502015901_2_1
3.2.5.7.
Customised display of analogue values
This screen lets the user view the specific analogue values.
15/10/2003
00 : 00: 00
GS 1
Personalised analog display
Stop
Faults
Alarm
FREE
+000000
FREE
+000000
FREE
+000.00
FREE
+000000
FREE
+00.000
FREE
+000000 157
FREE
+0000.0
FREE
+000000
Kerys Tactyl
FREE
+000000
FREE
+000000
Kerys
FREE
+000000
FREE
+000000
-2Electrical measurements JDB/Grid(s)
- 3Harmonics
- 1 Electrical measurements
157
Each set of analogue values only appears when an associated variable has been configured Warning
37/62
33502015901_2_1
3.2.6 Alarms and faults This menu can be brought onto screen by pressing the Alarms and Faults buttons on the upper bar. This screen allows the user to view the list of faults present on the installation. The first two columns give details of the date and time that the fault appeared. The Status column shows whether or not the fault is still present: 1 = yes or 0 = no. The @ column gives the location of the variable associated with the fault. The Title column gives details of the fault. A line on a red background shows a fault, and a line on an orange background shows an alarm.
15/10/2003
00: 00: 00
GS 1
Date
Time
Status
@
Title
26/11/03
11:11:12’55
1
6131
HT LOW COOLANT LEVEL FAULT
26/11/03
10:35:16’28
0
6017
INSULATION 1 ALARM
26/11/03
10:10:10’10
0
60C3
CIRCUIT BREAKER FAULT ON GENERATING SET OUTPUT
-1Function keys Active line
Alarms & faults
-2Synchronisation column
Stop
Faults
Alarms
-3Central unit measure. summary
Scroll down buttons for when the list is longer than the number of lines on the
To clear a fault, it is necessary to: check that the fault has disappeared (status 0) and, if necessary, remove the causes of the fault select the line in question; the text on the line is displayed in white press the Reset button on the keypad, and the line is cleared
Warning
38/62
When a fault is displayed, its effect on operation remains active even if the cause has disappeared. When in Manu or Auto mode, if the user wants to clear a fault with an "In stopped" clearance mode, a screen will inform the user to switch to Stop mode.
33502015901_2_1
3.2.6.1.
Help
This screen displays possible causes of a problem and what to check.
15/10/2003
00:00:00
GS 1
Fault number
60D6
Keywords
Title
Help
Stop
Faults
Alarm
THEN
ACTIVE OUTPUT MAXIMUM ALARM (32) Genset overload in active power. Check
Possible causes
Previous fault
Search
-1Digital I/O
-2Curves
Next fault -3Electrical faults
Searches can be done in two ways: enter a keyword enter the fault number Pressing in the "Checks" area displays a description of the checks.
15/10/2003
00:00:00
GS 1
Fault number
60D6
Keywords
Title
Help
Stop
Faults
Alarm
THEN
ACTIVE OUTPUT MAXIMUM ALARM (32) Adjust output to genset capacity. Drop part of the load. Possible causes
Check
Previous fault -1Digital I/O
Search -2Curves
Next fault -3Electrical faults
Pressing in the "Possible causes" area displays a description of the cause. The "Search" key launches a search.
39/62
33502015901_2_1
How to search: 1.
Enter a keyword or fault number.
2.
Launch the search by pressing on "Search".
3.
When the search is over, the user can display the possible cause or what to check by pressing the appropriate icon (right of screen).
4.
The user can display the previous or next fault found by the search by using the appropriate keys.
3.2.7 User settings This command has the following options: Operating modes: A612 - A622 - A641 - A642 - A651 - A661
15/10/2003
19:10:00
GS 1
User adjustments
Auto
Faults
Alarms
-0Operation
-1Set point -2Power threshold
-4User parameters 1/2
40/62
-5User parameters 2/2
33502015901_2_1
Operating modes: A633 - A634
15/10/2003
00:00:00
GS 1
User adjustments
Stop
Faults
Alarms
-0Operation
-1Set point -2Power threshold -3Wattmeter control -4User parameters 1/2
-5User parameters 2/2
Operating mode: A635
15/10/2003
00:00:00
GS 1
User adjustments
Stop
Faults
Alarms
-0Operation
-2Power threshold -3Wattmeter control -4User parameters 1/2
41/62
-5User parameters 2/2
33502015901_2_1
3.2.7.1.
Set points
This menu is used for defining set point values for adjusting the generating set. Designed for multi-voltage applications, this menu enables the required value for each set point to be defined. These values relate to the following parameters: Generating set Voltage Active power Power factor Reactive power
Grid Active power Power factor Reactive power
A green background indicates the active set point
Operating modes: A612 - A622 - A641 - A642 - A651 - A661 Voltage setting Designed for multi-voltage applications, enabling the required value for each set point to be defined. Power setting Enables the power and power factor values to be assigned for periods of operation coupled to the grid. Grid set point: the grid supplies a fixed output and the generating set control unit provides any additional power Genset set point: the generating set supplies a fixed output and the grid provides any additional power
42/62
33502015901_2_1
Operating modes: A633 - A634 Voltage setting Designed for multi-voltage applications, enabling the required value for each set point to be defined. Power setting Enables the power and power factor values to be assigned for periods of operation coupled to the grid. Grid set point: the grid supplies a fixed output and the generating set control unit provides any additional power Genset set point: the generating set supplies a fixed output and the grid provides any additional power
43/62
33502015901_2_1
3.2.7.2.
Power thresholds
In this menu the threshold values are defined, which, with the digital variables, authorise the creation of additional functions linked to the generating set or grid power. The green background indicates that the threshold value has been reached or exceeded.
Operating modes: A612 - A622 - A641 - A642 - A651 - A661
05/10/2003
00 : 00 :00
GS 1
Power threshold
Stop
Faults
Alarm
Gen set P thresholds as % of gen set Pn 4780
4781
4782
4783
4784
4785
4786
4787
10
15
20
30
40
50
75
100
Power plant P threshold as % of Power plant Pn 4788
4799
478A
478B
478C
478D
478E
478F
0
0
0
0
0
0
0
0
Stop
Faults
Alarm
-1 Set points
-2User parameters
Operating modes: A633 - A634 05/10/2003
00 : 00 :00
GS 1
Power thresholds
Gen set P thresholds as % of gen set Pn 4780
4781
4782
4783
4784
4785
4786
4787
10
15
20
30
40
50
75
100
Power plant P threshold as % of Power plant Pn 4788
4799
478A
478B
478C
478D
478E
478F
10
30
45
60
75
90
105
120
-1 Set points
44/62
-2User parameters
-3 Wattmetric control
33502015901_2_1
Operating mode: A635 05/10/2003
00 : 00 :00
GS 1
Power thresholds
Stop
Faults
Alarm
Gen set P thresholds as % of gen set Pn 4780
4781
4782
4783
4784
4785
4786
4787
10
15
20
30
40
50
75
100
Power plant P threshold as % of Power plant Pn 4788
4799
478A
478B
478C
478D
478E
478F
10
30
45
60
75
90
105
120
-2User parameters
45/62
-3 Wattmetric control
33502015901_2_1
3.2.7.3.
Wattmetric control / General parameters
Operating mode: A633 - A634 - A635 This section allows you to define th e icommissioning criteria of generating sets in a power plant according to the power requirements of the installation. The setting entry fields only appear if the With Wattmeter control selection is confirmed.
15/10/2003
00:00:00
GS 1
General parameters
Stop
Faults
Alarms
Avec
Wattmeter control Global operation time delay (sec):
70
Power on time delay (seconds)
10
Power off time delay (seconds)
10
Minimum number of GS
01
Maximum number of GS
05
Number of additional generating sets
0
-1Generating set priority
-2Thresholds
Global operation time delay: Time taken for all generating sets to be started and for generating sets to power the installation. Power on time delay: Time taken for the generating set to perform the power on keyway needed to power the installation. Power off time delay: Time taken for the generating set to perform the power off keyway needed to remove power from the installation. Minimum number of generating sets: Determines the minimum number of generating sets needed to start in order that the power plant can authorise the switching on of the installation. Maximum number of generating sets: All generating sets start when there is a request for emergency operation; the Wattmeter control only intervenes after an operation period allowing load stabilisation after the restart. This adjustment enables the number of generating sets starting during this sequence to be limited. Number of additional generating sets: Corresponds to the number of generating sets which have started in addition to the minimum number of generating sets needed to power the installation.
46/62
33502015901_2_1
3.2.7.4.
Wattmetric control / Thresholds
Operating mode: A633 - A634 - A635 Power-on thresholds These parameters are located in the left half of the on-screen configuration field. They define the active power threshold leading to an additional generating set start request. The power-on request is delayed for the duration of the time delay period to prevent the installation being started with a temporary overload, i.e. a motor starting, Power-off thresholds These parameters are located in the right half of the on-screen configuration zone. They define the active power threshold leading to the power-off request when the power consumption of an installation is reduced. If the threshold appears,the request to switch off the generating set is delayed for the duration of the time delay period.
15/10/2003
00: 00:00
GS 1
Thresholds
Stop
Faults
Alarms
1 GS => 2 GS
0%
0 kW
2 GS => 1 GS
0%
0 kW
2 GS => 3 GS
0%
0 kW
3 GS => 2 GS
0%
0 kW
3 GS => 4 GS
0%
0 kW
4 GS => 3 GS
0%
0 kW
4 GS => 5 GS
0%
0 kW
5 GS => 4 GS
0%
0 kW
5 GS => 6 GS
0%
0 kW
6 GS => 5 GS
0%
0 kW
6 GS => 7 GS
0%
0 kW
7 GS => 6 GS
0%
0 kW
-1General parameters
-2 Generating set priority
-3Thresholds 2
This only appears if there are more than 7 generating sets
47/62
33502015901_2_1
15/10/2003
00: 00:00
GS 1
Thresholds 2
Stop
Faults
Alarms
7 GS => 8 GS
0%
0 kW
8 GS => 7 GS
0%
0 kW
8 GS => 9 GS
0%
0 kW
9 GS => 8 GS
0%
0 kW
9 GS => 10 GS
0%
0 kW
10 GS => 9 GS
0%
0 kW
10 GS => 11 GS
0%
0 kW
11 GS => 10 GS
0%
0 kW
11 GS => 12 GS
0%
0 kW
12 GS => 11 GS
0%
0 kW
12 GS => 13 GS
0%
0 kW
13 GS => 12 GS
0%
0 kW
Faults
Alarms
-1Thresholds
-2Thresholds 3
This only appears if there are more than 13 generating sets
15/10/2003
00: 00:00
GS 1
Thresholds 3
Stop
13 GS => 14 GS
0%
0 kW
14 GS => 13 GS
0%
0 kW
14 GS => 15 GS
0%
0 kW
15 GS => 14 GS
0%
0 kW
-1Thresholds
-2Thresholds 2
On each threshold screen, only generating sets which do not exceed the maximum number of generating sets are monitored on screen.
48/62
33502015901_2_1
3.2.7.5.
Generating set priorities
Operating mode: A633 - A634 - A635 This function is used to select the order in which the generating sets are controlled by the Wattmetric control. Select the generating set of which you want to modify the priority level New level of priority selection 15/10/2003
00: 00:00
GS 1
Generating set priority
Stop
Faults
Alarms
Modification Genset selection
Priority selection
01
04
Cancelling modifications
Valid Display Gen set
1
2
3
4
5
6
7
Prio Priori rity ty
04
02
03
01
05
06
07
-1General parameters
-2Thresholds
Displays the priority attributed to each generating set again The number of generating set displayed depends depends on the number of the generating set declared in the power plant To modify the priority level assigned to a generating set: select the generating set (number) select the new priority confirm The previous priority of the modified generating set is assigned to the generating set affected by this change. Gen set
1
2
3
4
5
6
7
04
05
06
07
01
05
06
07
Before Priority
01
02
03 After
Modified priority
04
02
03
The "Return "Return to previous parameters" parameters" key allows the initial setting to be restored. This command is confirmed until it is saved in flash
49/62
33502015901_2_1
3.2.7.6.
User parameters (1/2)
This menu enables the user to modify certain settings in order to adapt operation to his requirements.
15/10/2003
00 : 00 :00
Power return confirmation request
GS 1
User parameters
No load test time delay (sec):
Without
Power 1
Power 2
Power loss time delay (sec):
3
3
Power return time delay (sec):
30
30
Inversion in noncoupling in emergency mode Inversion in noncoupling in normal mode
Stop
Without
Without
Without
Without
Faults
Alarm
600
-1 Set points According to the number of grids managed by the system Mains return confirmation request If the choice is "With "With ", when the grid voltage reappears, the mains return sequence is conditioned by additional signal.
Before confirming this selection, ensure that the equipment has been designed for this and that the command is present. Warning Power cut time delay Defines the time between the actual loss of the grid voltage and the beginning of the starting sequence. Mains return time delay Defines the time between the actual loss of the grid voltage and the start of the switching off sequence. If the "with mains return" return" selection is operational, this triggers the switching off sequence. Inversion in non-coupling in normal Enables a programme to be selected in the event of the grid synchronisation failing. If the "Without "Without"" selection is active, the installation remains supplied by the replacement power supply, if not, the installation cuts-off the supply. Inversion on non-connection in emergency Enables a program to be selected in the event of the grid synchronisation failing. If the "Without" Without" selection is active, the installation remains supplied by the grid, if not, the installation cuts-off the replacement power supply.
50/62
33502015901_2_1
3.2.7.7.
User parameters (2/2)
Access to this screen depends on the configuration.
Function (CRF/CRP): Choice of the type of coupling. This choice appears if the user has selected Long term synch (CRP) on the Configuration/Parameters/General screen. Power surge keyway (sec): Definition of the time delay associated with the power surge keyway (Range of values: 0 to 32767). Power off keyway (sec): Definition of the time delay associated with the power off keyway (Range of values: 0 to 32767). Starting mode: Choice of Starting mode. This choice is possible if the user has programmed 2 starters: non alternating alternating Starter priority: Choice of starter priority. This choice is possible when two starters have been configured. Pump priority: Choice of pump priority. This choice is possible when two pumps have been configured.
51/62
33502015901_2_1
3.3. Regional parameters The various display parameters can be selected from this menu: language selection for display setting the date and time setting the module synchronisation time
15/10/2003
00 : 00 :00
GS 1
Regional parameters
Stop
Faults
Français
English
Spanish
Deutsch
Portuguese
Language option
Day
Month
Year
Hours
Minutes
Seconds
26
11
03
16
20
00
00
00
Synchronisation time:
Alarm
Inhibit the keys -1Application identification
-2Software versions
-3Printing
The top on the bus enables the resetting of various time settings in real time defined by the synchronisation time. To authorise cleaning the touch panel, the key inhibition function locks for approximately twenty seconds and does not register any presses on the screen. A special screen shows the time elapsing.
4. Generating set starting modes 4.1. General information The aim of this section is to describe the actions to be carried out for starting a generating set in the various possible modes:
starting in manual mode starting using the no load test function starting using the load test function starting in automatic mode
4.2. Prerequisites Make sure that you use an operational installation which includes a standard module and a KERYS IHM.
52/62
33502015901_2_1
4.3. Manual starting
Check there are no faults : grey: no fault. ed: fault present. r grey: no alarm. red: alarm present.
If faults are present, the fault management screen can be accessed by pressing the reset button.
If no faults are present, manual mode can be activated by pressing the Manu button.
53/62
33502015901_2_1
The manual starting phase will begin once button 1 in the test unit is pressed.
The starting request is maintained until th e generating set group starts. This method may not under any circumstances be used to turn the motor over.
During the starting phase and until the alternator voltage stabilises, the green LED underneath the generating set symbol flashes, and then lights up permanently once the phase is complete.
The generating set may be stopped at any time by pressing the stop button or the 0 button in the test unit. The green LED underneath the generating set symbol goes out to indicate that the generating set has stopped.
54/62
33502015901_2_1
4.4. Starting using the no load test function
Check there are no faults: grey: no fault. ed: fault present. r grey: alarm not present. red: alarm present.
If faults are present, the fault management screen can be accessed by pressing the reset button.
If no faults are present, automatic mode can be activated by pressing the Auto button.
55/62
33502015901_2_1
