DIN Standard for Mining.pdf

Register of Mining Standards dated 2010-12

Published by

FABERG Normenausschuss Bergbau im DIN Deutsches Institut für Normung e.V. Contact

Hans Georg Blasgude [email protected]

FABERG Normenausschuss Bergbau

Page 1 of 45

Foreword

Normenausschuss Bergbau (FABERG) is an agency of DIN Deutsches Institut für Normung e.V., Berlin. As a joint establishment of the German mining industry, it is supported by Vereinigung Rohstoffe und Bergbau e.V., Berlin and managed by a governing body. From a management and staff point of view, it is associated with DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V. of Essen. F ABE RG is responsible for national standardisation standardisation in the the field of mining and acts acts as a representativ representative e for this field in E uropean uropean (CEN) *) and international (ISO) **) standardisation efforts, supporting the introduction of standards in its specialised field for any practice affected by these and is instrumental in establishing the German standards system. An association representing the interests of the mining industry was formed as early as at the end of the 1800s – as a joint effort of mines in the German Ruhr area – also dealing with issues of standardisation and recommending to its member companies the use of specific pipes and underground rail systems. After World War I, a committee was formed, dealing with standardisation on behalf of the coal mining industry in the German Rhineland and Westphalia. It was realised at an early date that standardisation involving the entire mining industry would be more effective and useful. This lead to the foundation of Fachnormenausschuss für den Bergbau (FaBerg) on November 28th, 1922 at Hannover. Whereas during the first years of FABERG’s existence, dimensional and type standards were primarily set up, these were increasingly followed by quality and demand-based standards. Personal safety equipment, too, was subject to standardisation at an early date. In 1955, during the ISO General Assembly at Stockholm, the foundation of a “Mining” technical committee - ISO/TC 82 – was resolved, management of which was transferred to FABERG. In addition to this, FABERG is responsible for German representation in ISO/TC 27 "Solid Mineral Fuels". Within the scope of its CEN work delegated by the EU, FABERG was allocated the CEN/TC 196/WG 3 "Hydraulically Powered Support“ and CEN/TC 305/WG 5 "Equipment and Protective Systems for Mining" Secretariat. FABERG co-operates with other standards committees of DIN, CEN and ISO at national, European and international level, in order to represent the interests of the mining industry. The Regis Registter of Stan Stand dard ards com comp prises ises ISO ISO stan stand dard ards of of TC 27 27 "Solid Solid Min Mineral eral Fuels Fuels"" and and of TC 82 82 "Min Mining ing". The regist egister er also also incl includ udes es Oper Operat atin ing g Recom Recomm mend endatio ations ns for for Mini Mining ng (Ber (Bergbau-Be au-Bettrieb iebsblä sblättter). er). These These are are recom ecomm mend endatio ations ns set up by professionals, based on the same principles, which are mandatory for wording DIN standards. Users of these recommendations are subject to examining whether any arrangements recommended in these are adequate. BergbauBetriebsblätter are published by DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V. Bergbau-Betriebsblätter may be ordered from DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V., FABERG, Normenausschuss Bergbau, Am Technologiepark 1, 45307 Essen, Tel: (0201) 172-1553. The Stan Stand dard ards Ins Insp pect ection ion Offic Office e of DIN in FABERG is avai availa lab ble for insp inspec ecttion ion of any any nat nationa ionall DIN stan stand dard ards. Resear Research ch work ork may be conveniently performed through the Perinorm database of BSI, AFNOR and DIN and ISO/IEC, CEN/CENELEC standards. Opening times times of Standards Standards Inspection Office Office (Norm (Normenauslegest enauslegestelle): elle): Monday to Friday: 8.00 a.m. to 11.30 a.m. and 1.00 p.m. to 2.30 p.m. --------*) CEN CE N = Comité Comité E uropéen uropéen de Normalisation Normalisation **) ISO IS O = International Organization Organization for Standardization


Page 2 of 45

Foreword

Normenausschuss Bergbau (FABERG) is an agency of DIN Deutsches Institut für Normung e.V., Berlin. As a joint establishment of the German mining industry, it is supported by Vereinigung Rohstoffe und Bergbau e.V., Berlin and managed by a governing body. From a management and staff point of view, it is associated with DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V. of Essen. F ABE RG is responsible for national standardisation standardisation in the the field of mining and acts acts as a representativ representative e for this field in E uropean uropean (CEN) *) and international (ISO) **) standardisation efforts, supporting the introduction of standards in its specialised field for any practice affected by these and is instrumental in establishing the German standards system. An association representing the interests of the mining industry was formed as early as at the end of the 1800s – as a joint effort of mines in the German Ruhr area – also dealing with issues of standardisation and recommending to its member companies the use of specific pipes and underground rail systems. After World War I, a committee was formed, dealing with standardisation on behalf of the coal mining industry in the German Rhineland and Westphalia. It was realised at an early date that standardisation involving the entire mining industry would be more effective and useful. This lead to the foundation of Fachnormenausschuss für den Bergbau (FaBerg) on November 28th, 1922 at Hannover. Whereas during the first years of FABERG’s existence, dimensional and type standards were primarily set up, these were increasingly followed by quality and demand-based standards. Personal safety equipment, too, was subject to standardisation at an early date. In 1955, during the ISO General Assembly at Stockholm, the foundation of a “Mining” technical committee - ISO/TC 82 – was resolved, management of which was transferred to FABERG. In addition to this, FABERG is responsible for German representation in ISO/TC 27 "Solid Mineral Fuels". Within the scope of its CEN work delegated by the EU, FABERG was allocated the CEN/TC 196/WG 3 "Hydraulically Powered Support“ and CEN/TC 305/WG 5 "Equipment and Protective Systems for Mining" Secretariat. FABERG co-operates with other standards committees of DIN, CEN and ISO at national, European and international level, in order to represent the interests of the mining industry. The Regis Registter of Stan Stand dard ards com comp prises ises ISO ISO stan stand dard ards of of TC 27 27 "Solid Solid Min Mineral eral Fuels Fuels"" and and of TC 82 82 "Min Mining ing". The regist egister er also also incl includ udes es Oper Operat atin ing g Recom Recomm mend endatio ations ns for for Mini Mining ng (Ber (Bergbau-Be au-Bettrieb iebsblä sblättter). er). These These are are recom ecomm mend endatio ations ns set up by professionals, based on the same principles, which are mandatory for wording DIN standards. Users of these recommendations are subject to examining whether any arrangements recommended in these are adequate. BergbauBetriebsblätter are published by DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V. Bergbau-Betriebsblätter may be ordered from DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V., FABERG, Normenausschuss Bergbau, Am Technologiepark 1, 45307 Essen, Tel: (0201) 172-1553. The Stan Stand dard ards Ins Insp pect ection ion Offic Office e of DIN in FABERG is avai availa lab ble for insp inspec ecttion ion of any any nat nationa ionall DIN stan stand dard ards. Resear Research ch work ork may be conveniently performed through the Perinorm database of BSI, AFNOR and DIN and ISO/IEC, CEN/CENELEC standards. Opening times times of Standards Standards Inspection Office Office (Norm (Normenauslegest enauslegestelle): elle): Monday to Friday: 8.00 a.m. to 11.30 a.m. and 1.00 p.m. to 2.30 p.m. --------*) CEN CE N = Comité Comité E uropéen uropéen de Normalisation Normalisation **) ISO IS O = International Organization Organization for Standardization


Page 2 of 45

The number s af t er t he t i t l es of DI N st andar andar ds and DI N dr af t s i n br acket s ar e pr i ce gr oup oups ( dat ed 2009- 01- 01) ; t hey corr espon espond d wi t h t he f ol l owi ng pr i ces: ces: Prei sgr sgr . EUR Prei sgr sgr . EUR Prei sgr sgr . EUR 01 14, 14, 70 19 114, 114, 00 37 280, 280, 60 02 21, 21, 50 20 119, 119, 00 38 304, 304, 30 03 21, 21, 50 21 124, 124, 50 41 323, 323, 90 04 21, 21, 50 22 129, 129, 10 42 343, 343, 20 05 30, 30, 60 23 134, 134, 00 06 37, 37, 10 24 139, 139, 60 07 43, 43, 40 25 144, 144, 10 08 49, 49, 90 26 149, 149, 10 09 56, 56, 10 27 154, 154, 60 10 62, 62, 20 28 159, 159, 70 11 68, 68, 60 29 164, 164, 60 12 75, 75, 10 30 169, 169, 50 13 81, 81, 10 31 174, 174, 20 14 87, 87, 40 32 190, 190, 80 15 93, 93, 80 33 204, 204, 10 16 99, 99, 10 34 220, 220, 80 17 104, 104, 00 35 232, 232, 80 18 108, 108, 80 36 256, 256, 80 Fur Fur t her i nf ormati on on pr i ces yo you wi l l get by DI N Deut eut sches sches I nst i t ut f ür Normung e. V. i n Ber l i n. The number s af t er t he t i t l es of " Ber gbaugbau- Bet r i ebsbl ät t er " i n br acket s ar e pr i ce gr oups ( dated 2009- 01- 01) ; t hey corr espon espond d wi t h t he f ol l owi ng pr i ces: Gr oup EUR 1 7, 7, 70 2 10, 10, 50 3 13, 13, 10 4 15, 15, 70 5 21, 21, 60


Page 3 of 45

Register Register of Mining Mining Standa Standards rds 2010-12 2010-12

F B Shaf S haftt 01 01

01 Shaft NA 008-01 008-01-01 -01-0 -01 1 AK Shaft s ink ing devices

DIN 21151 DIN DIN 21 21164 DIN 21181-1 DIN 21181-2

11.09 05.03 .03 03.10 03.10

DIN 21186

04.94

DIN 21187

04.94

DIN DIN 21 21194 DIN 21198

12.99 .99 11.09

Shaft sinking; pulleys for flat winding ropes; safety s afety requirements requirements and testing testing (8) Shaf Shaft sin sinking ing - Rid Riders ers for for wind inding ing kibb ibbles les - Saf Safety requirement ents an and test esting ing (12 (12) Shaft sinking Debris Debris kibbles - Part P art 1: Debris kibbles kibbles with with suspension hanger hanger (12) (12) Shaft sinking; debris debris kibbles kibbles - P art 2: 2: Debris kibbles with with suspension two-s two-str trand and chain set (9) Shaft sinking; rope rope suspension gears for load hoisting hoisting in shafts; shafts; safet safety y requirements and testing (6) Shaft sinking; chain chain suspension gears for load hoisting in shafts; shafts; safet safety y requirements and testing (5) Shaf Shaft sin sinking ing - Abu Abutment for guide ide ropes opes - Saf Safety ety requ equireme ements an and testin sting g (7) Shaft sinking - Shaft S haft plumbs plumbs (6)

NA 008-0 008-01-0 1-011-02 02 AK Freezing Freezing s haft c onst ruc tio n

DIN 4930

06.89 P ipes for use in freezing shaft sinking; sinking; dimensions dimensions and technical technical delivery delivery conditions (5)

NA 008-01-01-03 AK Shaft support

DIN 21500

11.01 Sha Shaft sin sinking in mining - Desig sign and dimensio sioning (12)

NA 008-01-02-01 AK Hoist ropes

DIN DIN 41 4118 DIN EN E N 12385-1 12385-1 DIN EN E N 12385-2 12385-2 DIN 12385-2/B1 DIN EN E N 12385-3 12385-3 DIN 123 12385 85-3/ -3/B1 B1 DIN EN E N 12385-6 12385-6 DIN EN 123 12385 85-7 -7 DIN 21258

06.81 .81 Hea Head frames an and winding towers fo for mines; Desi Desig gn loads, calculati ation principles and design principles (4) /FABERG co-author/ 01.09 Steel teel wire ropes - Safet S afety y - Part P art 1: General requirem requirement ents; s; Germ G erman an version version EN EN 12385-1:20 12385-1:2002+ 02+A1:2008 (12) /FABE /F ABER RG co-author/ co-author/ 06.08 Steel teel wire ropes - Safet S afety y - Part P art 2: Definition Definitions, s, designation and classification; German Version prEN 12385-2:20 12385-2:2002/+ 02/+A1:2008 (20) /FABE /FAB ERG co-aut co- author/ hor/ 01.09 Steel teel wire ropes - Safet S afety y - Part P art 2: Definition Definitions, s, designation and classification; German Version Version prEN prEN 12385-2:2002/+ 12385-2:2002/+A1:2008, A1:2008, Corrigendum Corrigendum to DIN DIN EN 12385.2:2008-06 /FABERG co-author/ 06.08 Steel teel wire ropes - Safet S afety y - Part P art 3: Information Information for use and maint maintenance; enance; German German version version EN E N 12385-3:20 12385-3:2004/+ 04/+A1:2008 (13) /FABE /FAB E RG co-aut co-author/ hor/ 01.0 01.09 9 Steel Steel wire ire rope ropess - Safet Safety y - Part 3: Infor Inform matio ation n for for use and and maint aintenan enance ce;; German versio version n EN 12385-3:2004/+A1:2008, Corrigendem Corrigendem to DIN DIN EN EN 12385.3:2008-06 /FABERG co-author/ 05.04 Steel teel wire wire ropes ropes - Safet S afety y - Part Part 6: Stranded Stranded ropes ropes for mine mine shafts; shafts; Germ German an version EN 12385- 6:2004 (12) 02.0 02.03 3 Steel Steel wire ire rope ropess - Safet Safety y - Part 7: Locked Locked coil coil rope ropess for for mine ine shaf shaftts; Germ German an version EN 12835-7:2002 (9) 10.07 Lubricants Lubricants and impregnat impregnating ing compounds compounds for friction friction hoist ropes in mining mining Safety requirements and testing (9)

NA 008-01-02 008-01-02-02 -02 AK Hangi ng g ears

DIN 21341 DIN 21346 DIN 21371 DIN 21376-1

08.86 11.89 01.88 07.88

Wooden mine guides (6) Squ Square head bolts for shaft guides (5) Rope attach attachm ments; ents; assem assemblies blies (5) Guide shoes shoes for shaft shaft convey conveyances ances and counterweig counterweight htss with with guide rollers in mining (5)


Page 4 of 45

Register of Mining Standards 2010-12 DIN 21376-2 DIN 21377 DIN 21381 DIN 21382 DIN 21383 DIN 21386 DIN 21388 DIN 21389 DIN 21390

FB Shaft 01

07.88 Guide shoes for shaft conveyances and counterweights with slide-ways in mining (5) 12.94 Steel railings for shaft conveyances in mining (5) 01.88 Rope attachments; thimble connection plates for round ropes (5) 01.88 Rope attachments; outer plates, inner plates (5) 01.88 Rope attachments; pins (5) 01.88 Rope attachments; thimbles for round ropes (5) 01.88 Rope attachments; universal joints (5) 01.88 Rope attachments; clamp thimbles (5) 02.85 Thimbles for flat ropes (5)

NA 008-01-02-03 AK Br aking calcul ations

DIN 20400 DIN 22400 DIN 22405 DIN 22406 DIN 22410

01.90 04.90 05.90 10.86

Knuckle threads for the mining; threads with large load-bearing depth (6) Control units of winding engines; hoists and winches for mining (5) Friction pulley linings for winches and winders in mining (5) Low speed Koepe winding machines with friction wheel, for shafts and drifts; braking system calculation formulae (13) 05.94 Winding rope pulleys for round ropes (10)


Page 5 of 45

Register of Mining Standards 2010-12

FB Mine Support 02

02 Mine Suppor t NA 008-02-01 AA Strut sup port

DIN 21315 DIN 21316 DIN 21317 DIN 21318 DIN 21320 DIN 21321 DIN 21324 DIN 21328 DIN 21546 DIN 21549 DIN 21550 DIN 21551 DIN 21555 DIN 21556 DIN 21557 DIN 21561

03.89 06.87 06.87 02.89 06.87 06.87 06.87 06.87 08.90 03.88 05.88 01.86 08.91 02.87 02.87 09.86

Round pit timber; load bearing capacity of props and bars; calculation (5) Round pit timber; props, bars (5) Round pit timber; timber for lagging (5) Round pit timber; pillar, supports (5) Round pit timber; technical quality and delivery requirements (6) Cut pit timber; square timber (5) Cut pit timber; wood for cogs (5) Cut pit timber; slabs (5) Mine support; strut support; marking (3) Mine supports; powered walking supports; terminology (5) Mine support; roof bars for single props; testing, requirements (5) Mine support; roof bars single props; lengths (5) Mine support; graphical symbols for the open loop control of powered support (6 Mine support; valves for individual props; identification code (5) Mine support; yield valves for powered support; identification code (5) Mine support; head for single props; connecting dimensions (5)

NA 008-02-02 AA Hydraulic po wered roof supp ort

DIN EN 1804-1 DIN EN 1804-2 DIN EN 1804-3

05.10 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 1: Support units and general requirements; English version EN 1804-1:2001+A1:2010 (16) 05.10 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 2: Power set and rams; German version EN 18042:2001+A1:2010 (16) 05.10 Machines for underground mines - Safety requirements for hydraulic roof supports - Part 3: Hydraulic control systems; German version EN 18043:2006+A1:2010 (15)

NA 008-02-03 AA Roadway s uppo rt

DIN 21319 DIN 21326 DIN 21327 DIN 21329 E BB 21510 DIN 21530-1 DIN 21530-2 DIN 21530-3 DIN 21530-4 DIN 21530-5 DIN 21531-1 DIN 21531-2 DIN 21548

02.89 Round pit timber; bolts (5) 04.89 Sawn pit timber; boards and planks (5) 02.89 Sawn pit timber; boards, planks and square-sawn timber for working platforms (5) 06.87 Cut pit timber; technical terms of delivery and quality (5) 06.95 Verzugsmatten - Technische Anforderungen (2) 05.03 Mine support - Part 1: General (5) 05.03 Mine support - P art 2: Dimensions, designation and statical values (21) 05.03 Mine support - Part 3: Requirements (10) 05.03 Mine support - P art 4: Testing (10) 05.03 Mine support - Part 5: Marking of parts of mine support (6) 07.90 Arch supports; arches B 5, 4 to B 20, 2 (5) 07.90 Arch supports; arches B 21, 7 to B 63 (5) 01.89 Rails for mine supports (5)


Page 6 of 45


FB Mine Support 02

NA 008-02-03-01 AK Bol ts f or mi ne supp ort

DIN 21521-1 DIN 21521-2 DIN 21522

07.90 Rock bolts for mining and tunnelling; terms (6) 02.93 Rock bolts for mining and tunnel support; general specifications for steel-bolts; tests, testing methods (7) 07.72 Roof bolt plates for mining and tunnel support (4)


Page 7 of 45


FB Extraction 03

03 Extractio n NA 008-03-01 AA Ext racti ng and st ow ing

DIN EN 1552 DIN 20012 DIN 20013 DIN 20097 DIN 20350

09.03 Underground mining machines - Mobile extracting machines at the face - Safety requirements for shearer loaders and plough systems; German version EN 1552:2003 (10) /FABERG co-author/ 04.89 Pneumatic stowing pipes (5) 04.89 Sealings for pneumatic stowing pipes (5) 07.68 Gears for coal ploughs and underground chain- conveyors; signs for gears (4) /FABERG co-author/ 03.75 Protective clothing - General requirements; German version prEN 340:2000 (4) /FABERG co-author/


Page 8 of 45


FB Tools 04

04 Tools NA 008-04-01 AA Hand tool s/Rock dr illi ng

DIN EN 815 DIN 1197-1 DIN 1197-2 DIN 6436 DIN 6437-1 DIN 6437-2 DIN 20109 DIN 20110 DIN 20112 DIN 20115 DIN 20119 DIN 20120 DIN 20121 DIN 20123 DIN 20124 DIN 20125 DIN 20127 DIN 20128 DIN 20129 DIN 20135 DIN 20136 DIN 20142 DIN 20151 DIN 20152 DIN 20301 DIN 20302 DIN 20311 DIN 20314 DIN 20361 DIN 20367 DIN 20369 DIN 20371 DIN 20372 DIN 20374 DIN 20375 DIN 20376

12.09 Safety of unshielded tunnel boring machines and rodles shaft boring machines for rock - Safety requirements; German version EN 815:1996+A2:2008 (16) /FABERG co-author/ 06.90 Eyes for picks, oval; dimensions, requirements, testing (5) 06.90 Pick eyes, oval; plug gauges (5) 06.90 Pickaxes (5) 06.90 Pickaxe handles; dimensions, requirements, testing (5) 06.90 Pickaxe handles; gauges (5) 06.90 Pickaxes, chisel and point ends (5) 06.90 Beater-pickaxes (5) 06.90 In triangular hand hoes (5) 06.90 Miners axes (5) 07.90 Trough shovel (5) 07.90 Sand shovel (5) 07.90 Digging shovel (5) 07.90 Rimmed shovel (5) 07.90 Pan shovel (5) 07.90 Loading shovel (5) 06.73 Spades (4) /FABERG co-author/ 07.90 Shallow rimmed shovel (5) 07.90 Plain shovel (5) 07.90 Sledge hammer (5) 07.90 Hand hammer (5) 07.92 Hacksaws with steel frames and two handles (5) 01.84 Gears for coal ploughs and underground chain- conveyors; signs for gears (4) /FABERG co-author/ 03.89 Shovel and spade handels; types, dimensions, requirements, testing, marking (5) /FABERG co-author/ 01.99 Rock drilling operations - Terminology, units, and symbols for use in formulae (9 02.74 Rock drilling operations - Terminology, units, and symbols for use in formulae (8) /FABERG co-author/ 11.02 Drill tubes with diameters exceeding 100 mm for large hole boring in mining (5) 06.90 Screw threads for drill tubes will diameters exceeding 100 mm for large hole boring in mining (5) 04.10 Rock drilling - Chuck bushings - Connecting dimensions, material, design (4) 04.10 Rock drilling - Round screw connections for rotary drilling equipment Dimensions, design (5) 09.89 Pick hammers; flat- and shearpick without and with shank (5) 09.69 Hammer drilling; connecting tap for hammer drilling support (4) /FABERG coauthor/ 05.88 Rock drilling; water tube; connecting dimensions, material, finish (5) 01.88 Pick hammers; gauges for picks (5) 01.88 Pick hammers; round picks without shank (5) 01.88 Pick hammers; round picks with shank (5)


Page 9 of 45

Register of Mining Standards 2010-12 DIN 20377 DIN 20378 DIN 20379 E DIN 20379-1 E DIN 20379-2 DIN 24063 DIN 68340

FB Tools 04

11.09 10.90 03.90 02.10 02.10 01.80

Rock drilling - Flush drills - Drill rod profiles, shanks and tapers (7) Drilling hammers; taper gauges for tapered connections of drill rods and bits (5) Drill bits with tapered connection for percussive wet rock drilling (5) Rock drilling - Part 1: Tapered bits for percussive flush drilling Rock drilling - Part 2: Bits with internal thread for percussive flush drlling Operating elements (control devices) for pneumatic tools; terms, safety requirements (4) /FABERG co-author/ 01.89 Timber handles for impact tools; technical specifications (5) /FABERG co-author


Page 10 of 45


FB Transport 05

05 Transpor t NA 008-05-01 AA Mine railways

DIN 5902 DIN 5904 DIN 5906 DIN 5914 DIN 20449 DIN 20450 DIN 20452-1 DIN 20452-2 DIN 20453-1 DIN 20453-2 DIN 20454 DIN 20455 DIN 20458 DIN 20460 DIN 20462-1 DIN 20462-2 DIN 20463-1 DIN 20463-2 DIN 20464 DIN 20465 DIN 20468 DIN 20470 DIN 20472-1 DIN 20472-2 DIN 20473-1

11.95 Fishplates for grooveless flat bottom rails dimensions - Steel types (10) /FABERG co-author/ 11.95 Steel sleepers - Dimensions, static values, steel types (6) /FABERG co-author/ 11.95 Short clips for grooveless flat bottom rails - Dimensions, steel types (6) /FABERG co-author/ 03.65 baseplate scrwes with rectangular head (4) /FABERG co-author/ 10.88 Points and crossovers for rail haulage roads in mines; standard types, terminology (7) 10.88 Simple underground track points; 20 m radius, 1 : 5 inclination; geometric dimensions (5) 10.88 Simple points for underground tracks with loose heel switch; 20 m radius, 1 : 5 inclination, 600 mm gauge; compilation (5) 10.88 Simple points for underground tracks with spring switch blade; 20 m radius, 1 : 5 inclination, 600 mm gauge; compilation (5) 10.88 Switches for simple underground track points with loose heel switch; 20 m radius, 1 : 5 inclination, 600 mm gauge (5) 10.88 Switches for simple underground track points with spring switch blade; 20 m radius, 1 : 5 inclination, 600 mm gauge (5) 10.88 Crossings for simple underground track points; 20 m radius, 1 : 5 inclination, 600 mm gauge (5) 10.88 Check rail device for simple underground track points; 20 m radius, 1 : 5 inclination, 600 mm gauge (5) 10.88 Simple crossovers for underground tracks; 20 m radius, 1 : 5 inclination; geometric dimensions (5) 10.88 Simple underground track points; 30 m radius, 1 : 6 inclination; geometric dimensions (5) 10.88 Simple points for underground tracks with loose heel switch; 30 m radius, 1 : 6 inclination, 600 mm gauge; compilation (5) 10.88 Simple points for underground tracks with spring switch blade; 30 m radius, 1 : 6 inclination, 600 mm gauge; compilation (5) 10.88 Switches for simple underground track points with loose heel switch; 30 m radius, 1 : 6 inclination, 600 mm gauge (5) 10.88 Switches for simple underground track points with spring switch blade; 30 m radius, 1 : 6 inclination, 600 mm gauge (5) 10.88 Crossings for simple underground track points; 30 m radius, 1 : 6 inclination, 600 mm gauge (5) 10.88 Check rail device for simple underground track points; 30 m radius, 1 : 6 inclination, 600 mm gauge (5) 10.88 Simple crossovers for underground tracks; 30 m radius, 1 : 6 inclination; geometric dimensions (5) 10.88 Simple underground track points; 50 m radius, 1 : 7 inclination; geometric dimensions (5) 10.88 Simple points for underground tracks with loose heel switch; 50 m radius, 1 : 7 inclination, 600 mm gauge; compilation (5) 10.88 Simple points for underground tracks with spring switch blade; 50 m radius, 1 : 7 inclination, 600 mm gauge; compilation (5) 10.88 Switches for simple underground track points with loose heel switch; 50 m radius, 1 : 7 inclination, 600 mm gauge (5)


Page 11 of 45

Register of Mining Standards 2010-12 DIN 20473-2 DIN 20474 DIN 20475 DIN 20478 DIN 20499 DIN 20500 DIN 20501 DIN 20506 DIN 20536 DIN 20537 DIN 20539 DIN 20548 DIN 20549 DIN 20550 DIN 20551 E DIN 20551 DIN 20552 DIN 20553 E DIN 20553 DIN 20555 E DIN 20555 DIN 20556 E DIN 20556 DIN 20560 DIN 20570 DIN 20575-1 DIN 20579-1 DIN 20579-2 DIN 20581 DIN 20583 DIN 20586 E DIN 20586 DIN 20600 DIN 20601 DIN 21325 E DIN 21325

FB Transport 05

10.88 Switches for simple underground track points with spring switch blade; 50 m radius, 1 : 7 inclination, 600 mm gauge (5) 10.88 Crossings for simple underground track points; 50 m radius, 1 : 7 inclination, 600 mm gauge (5) 10.88 Check rail device for simple underground track points; 50 m radius, 1 : 7 inclination, 600 mm gauge (5) 10.88 Simple crossovers for underground tracks; 50 m radius, 1 : 7 inclination; geometric dimensions (5) 01.07 Rail haulage roads in mines - General rules (12) 10.88 Underground mine railways; track gauges and rails; standard types and selection (5) 07.88 Pit railways; rails S 30, butt strap Fl 30 (5) 07.90 Clamping plates for securing rails onto steel supports (5) 01.92 Simple track points with spring switch blade; 120 m radius, 1:9 inclination, 900 mm gauge; compilation (6) 03.92 Switches for simple track points; 120 m radius, 1:9 inclination, 900 mm gauge (6) 03.92 Check rail device for simple track points; 120 m radius, 1:9 inclination, 900 mm gauge (5) 07.90 Wheel sets for rail vehicles used in mines; rules for measuring (5) 11.86 Track gauges for pit railways; definition and tolerances (5) 07.90 Mine cars size small; components, main dimensions, design (5) 07.90 Mine cars - front wall, casing, frame, buffer sheet (5) 08.10 Mine cars - front wall, casing, frame, buffer sheet (10) 11.88 Small size lubs; bumpers, supporting beam (5) 07.89 Wheel sets with taper roller bearings for mine cars; without springs (7) 08.10 Wheel sets with taper roller bearings for mine cars; without springs (8) 07.89 Wheel sets with taper roller bearings for mine cars; exterior spring suspension (7) 08.10 Wheel sets with taper roller bearings for mine cars; exterior spring suspension (11) 07.89 Wheel sets with taper roller bearings for mine cars; interior spring suspension (7 08.10 Wheel sets with taper roller bearings for mine cars; interior spring suspension (9 07.89 Mine cars; middle size; dimensions, design and construction (5) 04.89 Mine cars; large size; dimensions, design and construction (5) 10.03 Rail transport - Passenger cars for underground mining - Part 1: Requirements (6) 07.86 Buffer springs for mine cars; calculation (5) 07.86 Buffer springs for mine cars; requirements (5) 03.88 Mine cars; strap type coupling (5) 11.95 Mine cars - Shackle coupling (5) 05.91 Rail fastenings in mining for S 30 and S 33 rails on wooden sleepers (7) 08.10 Rail fastenings in mining for S 30E1 and 33E1 rails on wooden sleepers (8) 01.07 Mine railways - Wheel profils for locomotives and cars (5) 05.91 Mine cars; tyres for mine locomotives (5) 02.89 Pit converted timber; timber sleepers (5) 08.10 Pit converted timber; timber sleepers (5)


Page 12 of 45

Register of Mining Standards 2010-12 DIN 45635-52 DIN 45635-53 DIN 45635-54 DIN 45635-55

FB Transport 05

05.86 Measurement of airborne noise emitted by machines; enveloping surface method; mine diesel locomotives and mine road railers (5) /FABERG co-author/ 05.86 Measurement of airborne noise emitted by machines; enveloping surface method; diesel traction trolleys (5) /FABERG co-author/ 05.86 Measurement of airborne noise emitted by machines; enveloping surface method; mine trackless vehicles (5) /F ABERG co-author/ 05.86 Measurement of airborne noise emitted by machines; enveloping surface method; shunting trolleys with friction- wheel and/or gearwheel drive (5) /FABERG co-author/

NA 008-05-02 AA Suspended mono rails

DIN 20590 DIN 20592-1 DIN 20592-2 DIN 20593-1 DIN 20593-2 DIN 20593-3 DIN 20593-4 DIN 20594 DIN 20597 DIN 20599 DIN 20619 DIN 20620-1 DIN 20620-2 DIN 20620-3 DIN 20622 DIN 20625-1 DIN 20629-1 DIN 20629-2 DIN 20629-3 DIN 20633 DIN 20635 DIN 20636 DIN 20637

04.90 Securing devices on underframes used in mining (5) 08.91 Suspended monorails for mining; transport boxes; dimensions and requirements (5) 08.91 Suspended monorails for mining; attachment facilities for transport boxes; dimensions and requirements (5) 11.02 Monorails for mining - Rails - Part 1: Straight rails for profile I 140 E (7) 11.02 Monorails for mining - Rails - P art 2: Curved rails and adapting rails for profile I 140 E (8) 07.04 Monorails for minging - Rails - Part 3: Straight rails and rail-connections for profiles I 140V and I 250 (11) 04.07 Monorails for minging - Rails - Part 4: Curved rails and adapting rails for profiles I 140 V and I 250 (12) 08.91 Suspension claws for mining, for loads up to 30 kN; requirements and testing (7) 05.92 Suspended monorails for mining; toothed disc (5) 08.93 Suspended monorails for mining; rope positions, mounting devices, clearance dimensions for bogies (5) 08.93 Suspended monorails for mining; winding-drum with suspension hook; dimensions and requirements (6) 10.94 Force-guided tram-ways in mining - Part 1: Survey; structure and terms (5) 10.94 Force-guided tram-ways in mining - Part 2: Monorails; structure and terms (6) 10.94 Force-guided tram-ways in mining - Part 3: Free-steered machines; structure and terms (6) 11.02 Suspended-monorail transport systems for mining - Permissible loads for suspensions and their abnutments and railprofile I 140 E (10) 03.92 Capture-track rail installations in mining; bolted couplings for rope-hauled and self-propelled rail installations; bolted coupling 30 (7) 08.01 Suspended monorails for mining - Mounting regulations - Part 1: for cabledriven suspended monorails (7) 08.01 Suspended monorails for mining - Mounting regulations - Part 2: for loco-driven suspended monorails (8) 08.01 Suspended monorails for mining - Mounting regulations - Part 3: Calculations (5) 04.02 Overhead monorail installations for mining - Double-end fork turnbuckles (7) 05.01 Monorails for mining - Suspensions shackles (6) 06.01 Monorails for mining - Suspension claws - Requirements and testing (5) 10.97 Monorails for mining - Tested round steel chains for suspensions - Tested, long link (5)

NA 008-05-03 AA Belt conv eyors

DIN EN ISO 252

01.08 Conveyor belts - Ply adhesion between constitutive eleents - Test methods (ISO 252:2007); German version EN ISO:2007 (8) /FABERG co-author/


Page 13 of 45

Register of Mining Standards 2010-12 DIN EN ISO 283 DIN EN ISO 284 DIN EN ISO 340 DIN EN ISO 340/B1 DIN EN ISO 505 DIN EN ISO 583 DIN EN ISO 703 DIN EN ISO 1120 DIN EN 1554 DIN EN ISO 7590 DIN EN ISO 7622-1 DIN EN ISO 7622-2 DIN EN ISO 7623 DIN EN ISO 9856 DIN EN 12881-1 DIN EN 12881-2 DIN EN 12882 DIN EN 13827 DIN EN ISO 14890 DIN EN 14973 DIN 15207-1

FB Transport 05

02.08 Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2007); German version EN ISO 283:2007 (9) /FABERG co-author/ 04.04 Conveyor belts - Electrical conductivity - Specification and method of test (ISO 284:2003); German Version EN ISO 284:2003 (8) /FABERG co-author/ 06.07 Conveyor belts - Laboratory scale flammability characteristics - Requirements and test method (ISO 340:2004); German version EN ISO 340:2004 (8) /FABERG co-author/ 09.09 Conveyor belts - Laboratory scale flammability characteristics - Requirements and test method (ISO 340:2004); German version EN ISO 340:2004, Corrigendum to DIN EN ISO 340:2007-06 (99) /FABERG co-author/ 04.00 Conveyor belts - Method for the determination of the tear propagation resistance of textile conveyor belts (ISO 505:1999); German version EN ISO 505:1999 (6) /FABERG co-author/ 03.08 Conveyor belts with a textile carcass - Total belt thickness and thickness of constitutive elements - Method of test (ISO 583:2007); German version EN ISO 583:2007 (9) /FABERG co-author/ 03.08 Conveyor belts - Transverse flexibility (troughability) - Test method (ISO 703:2007); German version EN ISO 703:2007 (8) /FABERG co-author/ 06.02 Conveyor belts - Determination of strength of mechanical fastenings - Static test method (ISO 1120:2002); German version EN ISO 1120:2002 (7) /FABERG coauthor/ 01.99 Conveyor belts - Drum friction testing; German version EN 1554:1998 (6) /FABERG co-author/ 03.10 Steel cord conveyor belts - Methods for the determination of total thickness and cover thickness (ISO 7590:2001); German version EN ISO 7590:2001 (8) /FABERG co-author/ 11.95 Steel cord conveyor belts - Longitudinal traction test - Part 1: Measurement of elongation (ISO 7622-1:1984); German version EN ISO 7622-1:1995 (5) /FABERG co-author/ 11.95 Steel cord conveyor belts - Longitudinal traction test - Part 2: Measurement of tensile strength (ISO 7622-2:1984); German version EN ISO 7622-2:1995 (6) /FABERG co-author/ 08.97 Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after thermal treatment (ISO 7623:1996); German version EN ISO 7623:1997 (6) /FABERG co-author/ 07.04 Conveyor belts - Determination of elastic and permanent elongation and calculation of elastic modulus (ISO 9856:2003); German version EN ISO 9856:2003 (8) /FABERG co-author/ 01.10 Conveyor belts - Fire simulation flammability testing - Part 1: Propane burner tests; German version EN 12881-1:2005+A1:2008 (14) /FABERG co-author/ 10.09 Conveyor belts - Fire simulation flammability testing - Part 2: Large scale fire test; German version EN 12881-2:2005+A1:2008 (8) /FABERG co-author/ 03.10 Conveyor belts for general purpose use - Electrical and flammability safety requirements; German version EN 12882:2008 (11) /FABERG co-author/ 07.04 Steel cord conveyor belts - Determination of the lateral and vertical displacement of steel cords; German version EN 13827:2003 (7) /FABERG coauthor/ 11.05 Conveyor belts - Specification for rubberor plastics covered conveyor belts of textile construction for general use (ISO 14890:2003); German version EN ISO 14890:2003 (12) /FABERG co-author/ 12.09 Conveyor belts for use in underground installations - Electrical and flammability safety requirements; German version EN 14973:2006+A1:2008 (11) /FABERG co-author/ 10.00 Continuous mechanical handling equipment - Idlers for belt conveyors - Main dimensions of idlers for belt conveyors for bulk material (5) /FABERG co-author/


Page 14 of 45

Register of Mining Standards 2010-12 DIN EN ISO 15236-1 DIN EN ISO 15236-2 DIN EN ISO 15236-3 DIN EN ISO 15236-4 DIN EN ISO 16851 DIN 22101 E DIN 22101 DIN 22102-1 DIN 22102-2 DIN 22102-3 DIN 22107 DIN 22109-1 DIN 22109-2 DIN 22109-4 DIN 22109-5 DIN 22109-6 DIN 22110-2 DIN 22110-3 DIN 22117 DIN 22121 DIN 22122 DIN 22129-1 DIN 22129-2 DIN 22129-3 DIN 22129-4 DIN 22131-2 DIN 22131-3

FB Transport 05

04.06 Steel cord conveyor belts - Part 1: Design, dimensions and mechanical requirements for conveyor belts for general use (ISO 15236-1:2005); German version EN ISO 15236-1:2005 (12) /FABERG co-author/ 09.04 Steel cord conveyor belts - Part 2: Preferred belt types (ISO 15236-2:2004); German version EN ISO 15236-2:2004 (8) /FABERG co-author/ 04.08 Steel cord conveyor belts - Part 3: Special safety requirements for belts for use in underground installations (ISO 15236-3:2007); German version EN ISO 15236-3:2007 (11) /FABERG co-author/ 09.04 Steel cord conveyor belts - Part 4: Vulcanized belt joints (ISO 15236-4:2004); German version EN ISO 15236-4:2004 (8) /FABERG co-author/ 03.05 Textile conveyor belts - Determination of the net length of an endless (spliced) conveyor belt (ISO 16851:2004); German version EN ISO 16851:2004 (7) /FABERG co-author/ 08.02 Continuous conveyors - Belt conveyors for loose bulk materials - Basis for calculation and dimensioning (17) 02.10 Continuous conveyors - Belt conveyors for loose bulk materials - Basis for calculation and dimensioning (20) 04.91 Conveyor belts with textile plies for bulk goods - P art 1: Dimensions, specifications, marking (7) /FABERG co-author/ 04.91 Conveyor belts with textile plies for bulk goods - Part 2: Testing (5) /FABERG co author/ 04.91 Conveyor belts with textile plies for bulk goods - Part 3: Permanent joints (6) /FABERG co-author/ 08.84 Continous mechanical handling equipment; idler sets for belt conveyors for loose bulk materials; principal dimensions (5) /FABERG co-author/ 07.00 Conveyor belts with textile plies for coalmining - Part 1: Monoply belts for underground applications; dimensions, requirements (6) 07.00 Conveyor belts with textile plies for coalmining - Part 2: Rubber-belts with two plies for underground applications; dimensions, requirements (6) 07.00 Conveyor belts with textile plies for coalmining - Part 4: Rubber-belts with two plies for above ground applications; dimensions, requirements (6) 02.88 Conveyor belts with textile plies for coalmining; branding (5) 12.03 Conveyor belts with textile plies for coalmining - Part 6: Testing (6) 10.97 Testing methods for conveyor belt joints - Part 2: Endurance running tests, determination of running time of belt joints at conveyor belts with textile plies (5) 11.07 Testing methods for conveyor belt joints - Part 3: Determination of time strength for conveyor belt joints (dynamical testing method) (8) 02.88 Conveyor belts for coalmining; determination of the oxygen index (6) 07.00 Conveyor belts with textile plies for coalmining - Permanent joints for belts with one or two plies; dimensions, requirements, marking (6) 10.03 Continous mechanical handling equipment - Troughability of conveyor belts Determination of that portion of width of conveyor belting in contact with idlers, requrements, testing (6) 02.88 Steel cord conveyor belts for underground coalmining; dimensions, requirements (6) 02.88 Steelcord conveyor belts for underground coalmining; marking (5) 02.88 Steelcord conveyor belts for underground coalmining; testing (6) 11.91 Steelcord conveyor belts for use in underground coal mining; belt joints; dimensions, requirements (6) 11.88 Steelcord conveyor belts for hoisting and conveying; marking (5) 11.88 Steelcord conveyor belts for hoisting and conveying; testing (5)


Page 15 of 45

Register of Mining Standards 2010-12 DIN EN ISO 22721 DIN EN 28094 DIN 53530

FB Transport 05

01.10 Conveyor belts - Specification for rubber- or plastics-covered conveyor belts of textile construction for underground mining (ISO 22721:2007); German version EN ISO 22721:2007 (11) /FABERG co-author/ 05.94 Steel cord conveyor belts; adhesion strength test of the cover to the core layer (ISO 8094:1984); German version EN 28094:1994 (5) /FABERG co-author/ 02.81 Testing of organic materials; Separation test on fabric plies bonded together (5) /FABERG co-author/

NA 008-05-04 AA Constructions for belt conveyors

DIN 22111 DIN 22112-1 DIN 22112-2 DIN 22112-2 DIN 22112-3 DIN 22114 DIN 22114/B1 DIN 22114 DIN 22115 DIN 22116 DIN 22120

11.07 12.10 12.10 03.96 03.96 12.10 12.03 12.01 10.03

Belt conveyors for underground coal mining - Light construction (11) Belt conveyors for underground coal mining - Idlers - Part 1: Dimensions (6) Belt conveyors for underground coal mining - Idlers - Part 2: Requirements (5) Belt conveyors for underground coalmining - Idlers - Part 2: Requirements (5) Belt conveyors for underground coalmining - Idlers - P art 3: Testing (7) Belt conveyors for underground coalmining - Heavy construction (12) Corrigenda to DIN 22114:2001-12 Belt conveyors for underground coalmining - Heavy construction (8) Belt conveyors for underground coalmining; Coating on idlers; Requirements and testing (7) 10.03 Belt conveyors for underground coal mining - Pressure rollers DN 159 Dimensions, requirements, marking (6) 04.05 Elastomere scraper plates for belt conveyors in hard coal mines (6)

NA 008-05-05 AA Component s for chain c onveyor s

DIN 763 DIN 8175 DIN 8176 DIN EN 12321 DIN 22200 BB 22249 DIN 22252 E DIN 22252 DIN 22253 DIN 22255 E DIN 22255 DIN 22256 DIN 22257 DIN 22258-1 E DIN 22258-1 DIN 22258-2 DIN 22258-3 E DIN 22258-3

12.90 Tested, non-calibrated, long-link round steel chains (5) /FABERG co-author/ 02.80 Conveyor chains; bush conveyor chains, heavy type (4) /FABERG co-author/ 01.80 Conveyor chains; bush conveyor chains for haulage systems (4) /FABERG coauthor/ 07.09 Underground mining machinery - Specification for the safety requirements for armoured face conveyors; German version EN 12321:2003+A1:2009 (12) 05.94 Continous mechanical handling equipment; idler sets for belt conveyors for loose bulk materials; principal dimensions (5) /FABERG co-author/ 12.72 Schmiernippel für den Bergbau (2) 09.01 Round steel link chains for conveyors and winning equipment in mining (9) 04.10 Round steel link chains for use in continuous conveyors and winning equipment in mining (11) 03.08 Chain connectors - Shackle type connector units - Dimensions, requirements, testing (12) 08.01 Flat link chains for use in continuous conveyors in mining (9) 08.10 Flat link chains for use in continuous conveyors in mining (12) 10.02 Chain sprockets for chain conveyors and coal winning equipment - Dimensions, requirements, testing (11) 06.90 Scraper bars for chain conveyors; outboard chain assembly; dimensions, requirements, testing (5) 04.03 Chain connectors - Part 1: Flat type connectors (9) 08.10 Chain connectors - Part 1: Flat type connectors - Inactive for new design (10) 08.03 Chain connectors - P art 2: Kenter type connectors (9) 08.03 Chain connectors - Part 3: Block type connectors (8) 08.10 Chain connectors - Part 3: Block type connectors (10)


Page 16 of 45

Register of Mining Standards 2010-12 DIN 22259

FB Transport 05

05.07 Flightbars for use in chain conveyors in mining (10)

NA 008-05-06 AA Pipe systems

DIN 20002-1 DIN 20002-2 DIN 20002-3 DIN 20003-1 DIN 20003-2 DIN 20003-3 DIN 20004-1 DIN 20004-2 DIN 20006 DIN 20042 BB 20065-1 BB 20065-2 DIN 24251

11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominal pressure 10 (5) 11.89 Pipelines for mining; steel tubes with loose flanges and collars; projection and recess; nominal pressure 6 (5) 11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominal pressure 40 (5) 09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominal pressure 10 (7) 09.87 Steel tubes for mining; fittings with loose flanges and plain collars, projection and recess; nominal pressure 6 (7) 09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominal pressure 40 (6) 12.00 Steel tubes for mining - Part 1: Interpose rings rated for PN 10 and PN 40 (6) 12.00 Steel tubes for mining - Part 2: Wedge rings rated for PN 10 and PN 40 (5) 09.89 Pipeline for mining; sealings for steel tubes according to DIN 20002 and fittings according to DIN 20003 (5) 08.01 Watervalve, nominal pressure 40 - Dimensions and requirements (5) 02.78 Kunststoff-Rohrleitungen - Richtlinien für die Verlegung - Thermoplastische Kunststoffe (2) 02.78 Kunststoff-Rohrleitungen - Richtlinien für die Verlegung - Mitgeltende Normen (2) 08.73 Multistage centrifugal pumps; mine drainage pumps, with pump total head up to 1000 m at speed of rotation 1500 l/min (4) /FABERG co-author/

NA 008-05-07 AA Hose assemblies

DIN EN 853 DIN EN 854 DIN EN 856 DIN EN 857 DIN EN ISO 1402 DIN EN ISO 7751 DIN EN ISO 8030 DIN EN ISO 8031 DIN EN ISO 8033 DIN EN ISO 8330 DIN 20018-1

02.97 Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type Specification; German version EN 853:1996 (7) /FABERG co-author/ 02.97 Rubber hoses and hose assemblies - Textile reinforced hydraulic type Specification; German version EN 854:1996 (7) /FABERG co-author/ 02.97 Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification; German version EN 856:1996 (7) /FABERG coauthor/ 02.97 Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification; German version EN 857:1996 (6) /FABERG co-author/ 04.10 Rubber and plastic hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009); German version EN ISO 1402:2009 (10) /FABERG co-author/ 06.97 Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to design working pressure (ISO 7751:1991); German version EN ISO 7751:1997 (5) /FABERG co-author/ 02.98 Rubber and plastics hoses - Method of test for flammability (ISO 8030:1995); German version EN ISO 8030:1997 (6) /FABERG co-author/ 04.10 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and electrical conductivity (ISO 8031:2009); German version EN ISO 8031:2009 (12) /FABERG co-author/ 11.06 Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2006); German version EN ISO 8033:2006 (10) /FABERG co-author/ 02.10 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2007); German version prEN ISO 8330:2007 (14) /FABERG co-author/ 04.03 Textile-reinforced hoses - Part 1: Maximal working pressure PN 10/16 (7)


Page 17 of 45

Register of Mining Standards 2010-12 DIN 20018-2 DIN 20018-3 DIN 20018-4 DIN 20021

04.03 04.03 04.03 02.97

DIN 20029 DIN 20030

10.90 06.92

DIN 20033 DIN 20035 DIN 20036 DIN 20037 DIN 20038 DIN 20039 DIN 20040 DIN 20043 DIN 20044

07.90 10.90 10.90 10.90 10.90 08.98 10.90 09.03 05.03

DIN 20066

10.02

E DIN 20066

10.10

FB Transport 05

Textile-reinforced hoses - Part 2: Maximal working pressure PN 40 (5) Textile-reinforced hoses - Part 3: Maximal working pressure PN 100 (5) Textile-reinforced hoses - Part 4: Testing (6) Fluid-systems - Hoses with layer - Completation for DIN EN 853 to DIN EN 857 (5) Hose fittings; 1:3 taper gauges (5) Hose fittings; straight-way-cock with grip; dimensions, materials, requirements (5) Hose fittings; tapered nozzle with clamping nut (6) Hose fittings; flange nozzle; nominal pressure 16 (5) Hose fittings; coupling nipples with round thread form (5) Hose fittings; connecting nipple; dimensions (5) Hose fittings; coupling nozzles (5) Hose fittings - Hose clamps (5) Hose fittings; nipple valves; nominal pressure 16 (5) Staple-lock couplings for hydraulic power-transmission circuits (7) Staple-lock couplings type S for hydraulic power-transmission circuits Dimensions, requirements, testing (7) Hoses and hose assemblies; test methods suggestion for the configuration of documents (11) /FABERG co-author/ Hydraulic fluid power - Hose assemblies - Dimensions, requirements (12) /FABERG co-author/

NA 008-05-08 AA Mobile machines

DIN EN 1889-1 DIN EN 1889-2 DIN EN 12111

11.03 Machines for underground mines - Mobile machines working underground; safety - Part 1: Rubber tyred vehicles; German version EN 1889-1:2003 (15) /FABERG co-author/ 07.09 Machines for underground mines - Mobile machines working underground Safety - Part 2: Rail locomotives; German version EN 1889-2:2003+A1:2009 (20) 05.10 Tunnelling machines - Road headers, continuous miners and impact rippers Safety requirements; German version EN 12111:2002+A1:2009 (16) /FABERG co-author/


Page 18 of 45


FB Ventilation 06

06 Ventil ation NA 008-06-01 AA Air doors

DIN EN 12110 DIN 21631 E DIN 21631 DIN 21632 E DIN 21632 DIN 21633 E DIN 21633 DIN 21634 E DIN 21634 DIN 21635 DIN 21636 DIN 21637 DIN 21638 DIN 21639 DIN 21639/B1 DIN 21640-1

02.10 Tunnelling machines - Air locks - Safety requirements; German version EN 12110:2002+A1:2008 (12) /FABERG co-author/ 01.93 Air regulating systems in mining; wing air doors for travelling tracks; air doors without pressure reduction (7) 02.09 Air regulating systems for mining - Wing air doors for travelling tracks - Onewing type air doors without pressure reduction (11) 01.93 Air regulating systems in mining; wing air doors for haulage tracks; one-wing type doors without pressure reduction (7) 02.09 Air regulating systems for mining - Wing air doors for haulage tracks - One-wing type doors without pressure reduction (10) 10.93 Air regulating systems in mining; wing air doors for haulage tracks; double-wing type doors without pressure reduction (9) 03.09 Air regulating systems for mining - Wing air doors for haulage tracks - Doublewing type doors without pressure reduction (12) 05.99 Air regulation systems in mining - Swinging roadway air doors for monorails and free steered machines - Building and operation (9) 08.09 Air regulation systems for mining - Swinging roadway air doors for haulage tracks (10) 02.98 Air regulation systems in mining - Air locks - Building and operation (7) 04.03 Air regulation systems in mining - Belt-conveyors-way air locks - Dimensions, identifications, requirements and testing (12) 10.95 Air regulation systems in mining - Wing air doors for haulage tracks - Doublewing type doors with pressure reduction (8) 05.99 Air regulation systems in mining - Wing air locks for travelling tracks - Doublewing type doors with pressure reduction (6) 09.99 Air regulation systems in mining - Travel-way air locks - Type doors with pressure (5) 11.04 Corrigenda to DIN 21639:1999-09 10.93 Air regulating systems in mining; pneumatic cylinders for airdoors without pressure reduction; dimensions, requirement, marking (5)

NA 008-06-02 AA Installations for auxiliary ventilation

DIN 21603 DIN 21605 DIN 21606 DIN 21610 DIN 21612 DIN 21613 DIN 21614 DIN 21615 DIN 21625

10.09 Auxiliary ventilation for mining - Sheet airducting with collars and loose flanges (5) 07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for exhaust and forced ventilation - Spiral ventilation ducts (6) 07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for forced ventilation - Flat ventilation ducts (6) 07.10 Auxiliary ventilation in mining - Flexible plastic air ducts - Requirements and test methods (6) 07.10 Auxiliary ventilation for mining - Cladding material for flexible airducts Requirements, testing (5) 10.09 Auxiliary ventilation for mining - Steel sheet connectors with flange and shoulder (5) 10.09 Auxiliary ventilation for mining - Flanged sheet steel reducers (5) 10.09 Auxiliary ventilation for mining - Sheet steel reducers with flange and shoulder (5) 07.10 Fans with electric motor drive intended for use in potentially explosive atmospheres in coal mines (6)


Page 19 of 45

Register of Mining Standards 2010-12 DIN 21626

FB Ventilation 06

07.10 Fans with hybrid (electric/pneumatic) motor drive intended for use in potentially explosive atmospheres in coal mines (6)


Page 20 of 45


FB Mine Safety 07

07 Mine Safety NA 008-07-01 AA Person al safety and p rotect ive equipm ent

DIN EN 795/A1 DIN EN 795 E DIN EN 795 DIN EN 1497 DIN EN 1498 DIN 5290-1 DIN 7472-2 DIN EN ISO 14122-1 DIN EN ISO 14122-2 DIN EN ISO 14122-3 DIN EN ISO 14122-4 DIN EN 14404 DIN 20180 DIN 20182 DIN EN ISO 20344 DIN EN ISO 20345 E DIN EN ISO 20345 DIN EN ISO 20346 E DIN EN ISO 20346 DIN EN ISO 20347/B1 DIN EN ISO 20347

01.01 Protection against falls from a height - Anchor devices - Requirements and testing; Amendment A1; German version EN 795:1996/A1:2000 (6) /FABERG co-author/ 08.96 Protection against falls from a height - Anchor devices - Requirements and testing; German version EN 795:1996 (10) /FABERG co-author/ 06.09 Personal fall protection equipment - Anchor devices; German version prEN 795:2009 (15) /FABERG co-author/ 10.07 Personal fall protection equipment - Rescue harnesses; German version EN 1497:2007 (10) /FABERG co-author/ 01.07 Personal fall protection equipment - Rescue loops; German version EN 1498:2006 (11) /FABERG co-author/ 04.83 Snap hook from light metal; with setting nut; dimensions, requirements and testing (5) /FABERG co-author/ 01.91 Safety harness; steel fittings; connecting dimensions, safety requirements and testing (6) /FABERG co-author/ 01.02 Safety of machinery - Permanent means of access to machinery - Part 1: Choise of fixed means of access between tow levels (ISO 14122-1:2001); German version EN ISO 14122-1:2001 (8) /FABERG co-author/ 01.02 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and wlkways (ISO 14122-2:2001); German version EN ISO 14122-2:2001 (7) /FABERG co-author/ 01.02 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001); German version EN ISO 14122-3:2001 (9) /FABERG co-author/ 12.04 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2004); German version EN ISO 14122-4:2004 (14) /FABERG co-author/ 02.05 Personal protective equipment - Knee protectors for work in the neeling position; German version EN 14404:2004 (12) /FABERG co-author/ 06.10 Pulley for clothes hoists in pithead baths (5) 06.10 Double loop chain for hoisting clothes in pithead baths - Not tested, noncalibrated (4) 11.07 Personal protective equipment - Test methods for footwear (ISO 20344:2004+Amd.1:2007); German Version EN ISO 20344:2004+AC:2005*A1:2007 (26) /FABERG co-author/ 12.07 Personal protective equipment - Safety footwear (ISO 20345:2004+AMD1:2007); German Version EN ISO 20345:2004+AC:2007+A1:2007 (15) /FABERG co-author/ 05.09 Personal protective equipment - Safety footwear (ISO/DIS 20345:2009); German version prEN ISO 20345:2009 (16) /FABERG co-author/ 12.07 Personal protective equipment - P rotective footwear (ISO 20346:2004+AMD1:2007); German version EN ISO 20346:2004+AC:2007+A1:2007 (15) /FABERG co-author/ 05.09 Personal protective equipment - Protective footwear (ISO/DIS 20346:2009); German version prEN ISO 20346:2009 (16) /FABERG co-author/ 08.07 Personal protective equipment - Occupational footwear (ISO 20347:2004); German Version EN ISO 20347:2004, Corrigenda to DIN EN ISO 20347:200410; German version EN ISO 20347:2004/AC:2007 (99) /FABERG co-author/ 12.07 Personal protective equipment - Occupational footwear (ISO 20347:2004+AMD1:2007); German version EN ISO 20347:2004+AC:2007+A1:2007 (15) /FABERG co-author/


Page 21 of 45

Register of Mining Standards 2010-12 DIN 21800 DIN 21802 DIN 23301 DIN 23307 DIN 23311-1 DIN 23311-2 DIN 23320-1 DIN 23320-2 DIN 23320-3 DIN 23320-4 DIN 23320-5 DIN 23323 DIN 23327 DIN 23328 DIN 23330 DIN 23341 DIN 23342 DIN 23343 DIN 23344 DIN 23345 DIN 23346 DIN 23400 DIN 23405 DIN 24320 DIN 24531-1 DIN 24531-2 DIN 24531-3 DIN 24534 DIN 24537-1 DIN 24537-2 DIN 24537-3 DIN 34300 DIN 51502 DIN 51634

FB Mine Safety 07

06.89 06.89 03.07 06.09 06.85 02.98 04.98

Symbol mallet and iron (5) Symbols for mine rescue and gas protection squads (6) Safety footwear for underground mining (9) Leather backside protectors for miners (back skin) (5) Knee pads for mining; rubber knee pads (5) Knee pads for mining - Part 2: Plastic knee pads (6) Flameproof protective clothing for the mining industry - Part 1: Safety requirements and testing (5) 09.03 Flameproof protective clothing for the mining industry - Protecting clothing for people of mine rescue, gas rescue and fire rescue crews - Part 2: Single piece working suits (combinations) (5) 09.03 Flameproof protective clothing for the mining industry - Protecting clothing for people of mine rescue, gas rescue and fire rescue crews - Part 3: Two-piece working suits (5) 09.03 Flameproof protective clothing for the mining industry - Protecting clothing for people of mine rescue, gas rescue and fire rescue crews - Part 4: Underwear (5) 10.04 Flameproof protective clothing for the mining industry - Protecting clothing for people of mine rescue, gas rescue and fire rescue crews - Part 5: Protective hoods (7) 05.07 Bathing sandals for miners (5) 07.03 Shin protectors for mining (7) 09.03 Clothing for the mining industry - Woven farbics for work suits (6) 11.01 Safety markings for mines (15) 05.05 Clothing for the mining industry - Two-piece work suits (J acket and trousers) (7) 08.05 Clothing for the mining industry - Singlet with 1/4 sleeves (7) 03.07 Clothing for the mining industry - Shirt for miners (7) 09.03 Clothing for the mining industry - Men's slip (6) 08.05 Clothing for the mining industry - Long underpants (7) 09.03 Clothing for the mining industry - Socks for mining workers (6) 11.08 Rescue stretcher for mining (dragging basket) - Safety requirements and testing (10) 10.04 First aid boxes and first aid material for use in mining (6) 12.06 Fire resistant fluids - Hydraulic fluids of categories HFAE and HFAS Characteristics and requirements (7) /FABERG co-author/ 04.06 Gratings used as stairtreads - Part 1: Metal gratings (7) /FABERG co-author/ 08.07 Gratings used as stairtreads - Part 2: Sheet metal gratings (7) /FABERG coauthor/ 08.07 Gratings used as stairtreads - Part 3: Plastic gratings (6) /FABERG co-author/ 03.70 Chain locks (4) /FABERG co-author/ 04.06 Gratings used as floor coverings - Part 1: Metal gratings (7) /FABERG co-author 08.07 Gratings used as floor coverings - Part 2: Sheet metal gratings (7) /FABERG coauthor/ 08.07 Gratings used as floor coverings - Part 3: Plastic gratings (7) /FABERG coauthor/ 04.01 Rescue equipment - Rescue hooks with safety eyelet holes (6) /FABERG coauthor/ 08.90 Designation of lubricants and marking of lubricant containers, equipment and lubricating points (7) /FABERG co-author/ 12.81 Mineral spirits; safety lamps mineral spirit; minimum requirements (5) /FABERG co-author/


Page 22 of 45


FB Mine Safety 07

NA 008-07-02 AA Li ghti ng

DIN 20609 DIN 20610 DIN 22433 DIN 22434-1 DIN 22434-2 DIN 22434-3 DIN 22434-4 DIN 22434-5 DIN 22434-6 DIN 22434-7 DIN 22434-8 DIN 22434-9 DIN 22434-10 DIN 49659 DIN 49741 DIN 49834

11.93 Lighting of mine locomotives; head lamps; design features, photometric requirements, meters and measurements (6) 04.94 Lighting of mine locomotives; position lamps; design features, photometric requirements (5) 10.03 Underground lighting in hardcoal mining - Terms (6) 07.01 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 1: General specification (6) 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 2: Coalfaces with shield support (5) 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 3: T-junctions (5) 11.96 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 4: Conveyor belt (5) 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 5: Material handling places (5) 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 6: Area of roadway-driving operation (5) 07.95 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 7: Pit-bottom (5) 01.04 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 8: Building sites (5) 10.98 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 9: Areas of rail track operation (5) 02.05 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 10: Workshops and special premises (6) 12.86 Fluorescent lamps, non preheated for potentially explosive atmospheres (5) /FABERG co-author/ 11.68 Lamp cap BX22d/32 (4) /FABERG co-author/ 08.69 Electric lamps for portable miner's luminaires (4) /FABERG co-author/

NA 008-07-02-01 AK Capli ght s

DIN EN 62013-1 DIN EN 62013-2

02.07 Caplights for use in mines susceptible to firedamp - Part 1: General requirements - Construction and testing in relation to the risk of explosion (IEC 62013-1:2005); German version EN 62013-1:2006 (16) /FABERG co-author/ 02.07 Caplights for use in mines susceptible to firedamp - Part 2: Performance and other safety-related matters (IEC 62013-2:2005); German version EN 620132:2006 (12) /FABERG co-author/

NA 008-07-03 AA Explosion prevention and protection

DIN EN 1127-2 DIN EN 1710 DIN EN 13463-1 DIN EN 13463-5

07.10 Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology in mining; German version EN 11272:2002+A1:2008 (17) 08.08 Equipment and components intended for use in potentially explosive atmospheres in underground mines; German version EN 1710:2005+A1:2008 (17) 07.09 Non-electrical equipment for use in potentially explosive atmospheres - P art 1: Basic method and requirements; German versionrEN 13463-1:2009 (26) /FABERG co-author/ 03.04 Non-electrical equipment for potentially explosive atmospheres - Part 5: Protection by constructional safety "c"; German version EN 13463-5:2003 (13) /FABERG co-author/


Page 23 of 45

Register of Mining Standards 2010-12 DIN EN 14591-1/B1 DIN EN 14591-1 DIN EN 14591-2 DIN EN 14591-4 DIN EN 14983 DIN 21577 DIN EN 50303

FB Mine Safety 07

06.06 Explosion prevention and protection in underground mines - Protective systems - Part 1: 2-bar explosion proof ventilation structures, Corrigenda to DIN EN 14591-1:2004-12; German version EN 14591-1:2004/AC.2006 (99) 12.04 Explosion prevention and protection in underground mines - Protective systems - Part 1: 2-bar explosion proof ventilation structures; German version EN 14591-1:2004 (10) 07.07 Explosion prevention and protection in underground mines - Protective systems - P art 2: Passive water trough barriers; German Version EN 145912:2007 (17) 09.07 Explosions prevention and protection in underground mines - Protective systems - Part 4: Automatic extinguishing systems for road headers; German version prEN 14591-4:2005 (9) 06.07 Explosion prevention and protection in underground mining - Equipment and protective systems for firedamp drainage; German version EN 14983:2007 (13) 09.96 Explosibility of coal dust in underground hard coal mining - Tests and assessments of coal dust-air-mixtures and hybrid mixtures (8) 05.01 Group 1, category M1 equipment intended to remain functional in atmospheres endangered by firedamp and/or coal dust; German version EN 50303:2000 (7) /FABERG co-author/

NA 008-07-03-01 AK Apparatus for potentially explosive atmospheres for mining

DIN EN 1834-2

DIN 20401 DIN 22412 DIN 22416 DIN 22417 DIN 22418 DIN 22419-1 DIN 22419-2 DIN 22419-3 DIN 22424 DIN 22425 DIN 46295-1 DIN 46295-2 DIN 46295-3

03.00 Reciprocating internal combustion engines - Safety requirements for design and construction of engines for use in potentially explosive atmospheres - Part 2: Group I engines for use in underground workings susceptible to firedamp and/or combustible dust; German version EN 1834-2:2000 (10) /FABERG co-author/ 12.04 Buttress threads - 0,8 mm to 2 mm pitch - Dimensions (6) 04.86 Slit-bolts (5) /FABERG co-author/ 09.86 Electrical apparatus for potentially explosive atmospheres in mining; triangular head bolts; safety requirements and testing (5) 11.88 Electrical apparatus for potentially explosive atmospheres; forms of keys for triangular socket wrenches (5) 04.89 Electrical apparatus for potentially explosive atmospheres for mining; screw plugs; safety requirements and testing (6) 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable entries - Part 1: Requirements for basic design (8) 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable entries - Part 2: Gland adaptors for entries; safety requirements and testing (6) 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable entries - Part 3: Gland flanges for entries; safety requirements and testing (7) 03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangle head bolts (6) 03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangular nuts (6) 04.85 Terminal board, square shaped with six slit-bolts; main dimensions (5) /FABERG co-author/ 10.81 Terminal board, square shaped with six slit-bolts; accessories (6) /FABERG coauthor/ 10.81 Terminal board, square shaped with six slit-bolts; cable sockets (5) /FABERG co-author/

NA 008-07-04-01 AK Explosives

DIN EN 13631-1

07.05 Explosives for civil uses - High explosives - Part 1: Requirements; German version EN 13631-1:2005 (7)


Page 24 of 45

Register of Mining Standards 2010-12 DIN EN 13631-2 DIN EN 13631-3 DIN EN 13631-4 DIN EN 13631-5 DIN EN 13631-6 DIN EN 13631-7 DIN EN 13631-10 DIN EN 13631-11 DIN EN 13631-12 DIN EN 13631-13 DIN EN 13631-14 DIN EN 13631-15 DIN EN 13631-16 DIN 20163 DIN 20164-1

FB Mine Safety 07

12.02 Explosives for civil uses - High explosives - Part 2: Determionation of thermal stability of explosives; German version EN 13631-2:2002 (7) 11.04 Explosives for civil uses - High explosives - Part 3: Determionation of sensitiveness to friction of explosives; German version EN 13631-3:2004 (8) 12.02 Explosives for civil uses - High explosives - Part 4: Determionation of sentiveness to impact of explosives; German version EN 13631-4:2002 (8) 12.02 Explosives for civil uses - High explosives - Part 5: Determionation of resistance to water; German version EN 13631-5:2002 (7) 12.02 Explosives for civil uses - High explosives - Part 6: Determionation of resistance to hydrostatic pressure; German version EN 13631-6:2002 (7) 02.04 Explosives for civil uses - High explosives - Part 7: Determionation of safety and reliability at extreme temperatures; German version EN 13631-7:2003 (7) 02.04 Explosives for civil uses - High explosives - Part 10: Method for the verification of the means of initiation; German version EN 13631-10:2003 (8) 02.04 Explosives for civil uses - High explosives - Part 11: Determionation of transmission of detonation; German version EN 13631-11:2003 (8) 02.05 Explosives for civil uses - High explosives - P art 12: Specification of boosters with different initiating capability; German version EN 13631-12:2004 (6) 07.03 Explosives for civil uses - High explosives - Part 13: Determionation of density; German version EN 13631-13:2003 (7) 07.03 Explosives for civil uses - High explosives - Part 14: Determionation of velocity of detonation; German version EN 13631-14:2003 (8) 07.05 Explosives for civil uses - High explosives - Part 15: Calculation of thermodynamic properties; German version prEN 13631-15:2003 (12) 11.04 Explosives for civil uses - High explosives - Part 16: Detection and measurement of toxic gases; German version EN 13631-16:2004 (7) 11.94 Blasting - Terminology, units and symbols (14) 01.07 Blasting supplies - Explosives - Part 1: Requirements, testing, marking (12)

NA 008-07-04-02 AK Detonating cords

DIN EN 13630-1 DIN EN 13630-2 DIN EN 13630-3 DIN EN 13630-4 DIN EN 13630-5 DIN EN 13630-6 DIN EN 13630-7 DIN EN 13630-8

03.04 Explosives for civil uses - Detonating cords and safety fuses - Part 1: Requirements; German version EN 13630-1:2003 (7) 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 2: Determination of thermal stability of detonating cords and safety fuses; German version EN 13630-2:2002 (7) 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 3: Determination of sensitiveness to friction of the core of detonating cords; German version EN 13630-3:2002 (6) 12.02 Explosives for civil uses - Detonating cords and safety fuses - P art 4: Determination of sensitiveness to impact of detonating cords; German version EN 13630-4:2002 (8) 03.04 Explosives for civil uses - Detonating cords and safety fuses - P art 5: Determination of resistance to abrasion of detopnating cords; German version EN 13630-5:2003 (9) 12.02 Explosives for civil uses - Detonating cords and safety fuses - P art 6: Determination of resistance to tension of detonating cords; German version EN 13630-6:2002 (6) 12.02 Explosives for civil uses - Detonating cords and safety fuses - P art 7: Determination of reability of initiation of detonating cords; German version EN 13630-7:2002 (6) 12.02 Explosives for civil uses - Detonating cords and safety fuses - P art 8: Determination of resistance to water of detonating cords and safety fuses; German version EN 13630-8:2002 (7)


Page 25 of 45

Register of Mining Standards 2010-12 DIN EN 13630-9 DIN EN 13630-10 DIN EN 13630-11 DIN EN 13630-12 DIN 20165

FB Mine Safety 07

07.04 Explosives for civil uses - Detonating cords and safety fuses - P art 9: Determination of transmission of detonation from detonating cord to detonating cord; German version EN 13630-9:2004 (7) 08.05 Explosives for civil uses - Detonating cords and safety fuses - P art 10: Determination of initiating capacity of detonating cords; German version EN 1360-10:2005 (8) 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 11: Determination of velocity of detonation of detonating cords; German version EN 13630-11:2002 (6) 12.02 Explosives for civil uses - Detonating cords and safety fuses - P art 12: Determination of burning duration of safety fuses, German version EN 1363012:2002 (6) 08.10 Blasting supplies - Intrinsically safe detonators (permitted detonators) Requirements and testing (8)

NA 008-07-05 AA Plastics

DIN 22100-1 DIN 22100-3 DIN 22100-4 DIN 22100-5 DIN 22100-6 DIN 22100-7 E DIN 22100-7 DIN 22118

07.09 Articles and materials from synthetics for use in underground mines - Part 1: Conveyor belts - Hygienic requirements, testing, marking (8) 10.10 Articles and materials from synthetic for use in underground mines - Part 3: Spiral air ducts - Safety requirements, testing, marking (8) 10.10 Articles and materials from synthetic for use in underground mines - P art 4: Flat air ducts - Safety requirements, testing, marking (6) 10.10 Articles and materials from synthetic for use in underground mines - Part 5: Tubes, tube isolations and hoses - Safety requirements, testing, marking (8) 10.10 Articles and materials from synthetic for use in underground mines - Part 6: Sheeting, coated/uncoated tissue, brattice materials and lagging mats - Safety requirements, testing, marking (7) 06.00 Articles and materials from synthetics for use in underground mines - Part 7: Safety requirements, testing, marking (17) 08.10 Synthetic materials for use in underground mines - Part 7: Safety requirements, testing, marking (24) 08.91 Conveyor belts with textile plies for use in coal mining; fire testing (6)


Page 26 of 45


FB Analysis of Raw Material/Coal preparation 0

08 Analysi s of Raw Material/Coal pr eparatio n NA 008-08-01 AA Investi gation s of r aw material/Preparation of hard coal

DIN 22005-1 DIN 22005-2 DIN 22013 DIN 22014 DIN 22017 DIN 22018 DIN 22019-1 DIN 22019-2 DIN 22020-1 DIN 22020-2 DIN 22020-3 DIN 22020-4 DIN 22020-5 BB 22020-7 DIN 22021 DIN 22024 DIN 23004-1 DIN 23004-2 DIN 23005 DIN 23006-1 DIN 23006-2 DIN 23006-3 DIN 23006-4

09.97 Investigations of raw material in hard-coal-mining - Part 1: Survey (8) 09.97 Investigations of the raw material in hard-coal-mining - Part 2: Terms relating to raw material (13) 08.85 Investigations of the raw material in hard-coal-mining - Channel sample Sampling and schema of tests (9) 08.85 Investigations of the raw material in hard-coal mining - Raw coal sample from the production of a working area - Sampling and schema of tests (10) 03.08 Investigations of the raw material in hard-coal-mining - Froth-flotation-analysis (12) 01.85 Investigations of the raw material in hard-coal-mining determation of the particledensity-distribution by float-and-sink-analysis (10) 03.85 Investigations of the raw material in hard-coal-mining; determination of the particle-size-distribution 20 µm by sieve-analysis (12) 03.85 Investigations of the raw material in hard-coal-mining - Determination of the particle-size-distribution - Part 1: Particle-size-distribution < 60 µm by ultrasonicmicrosieve-analysis (7) 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 1: Terms, survey of processes and their applications (7) 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 2: Preparation of polished surface from lump material and particulate blocks (5) 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 3: Maceral analysis on particulated blocks (5) 12.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 4: Microlithotype analysis on particulate blocks (6) 02.05 Investigations of the raw material in hard-coal-mining - Microscopical examinations of hard coal, coke and briquettes - Part 5: Reflectance measurements on vitrinites (12) 09.74 Mikroskopische Untersuchungen an Steinkohlen, Koksen und Briketts Sonderuntersuchungen (4) 07.85 Investigations of the raw material in hard-coalmining - Microscopical examinations of rocks (17) 02.89 Investigations of the raw material in hard-coal-mining - Determination of tensile strength on solid rock (5) 01.87 Preparation of hard coal - Part 1: Survey (6) 05.88 Preparation of hard coal - Part 2: Terms relating to processes (15) 12.88 Preparation of hard coal - Description and estimation of raw coal properties in view of preparation (10) 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 1: General rules, balance of quantities (15) 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 2: Sizing (14) 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 3: Cleaning (13) 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - P art 4: Separation of solids from water (12)


Page 27 of 45

Register of Mining Standards 2010-12 DIN 23006-5 DIN 23006-6 DIN 23006-7 DIN 23007 DIN 23008 DIN 23009 DIN 23010-1 DIN 23010-2 DIN 23011-2 DIN 23011-3 DIN 23011-4 DIN 23011-5 DIN 23011-6 DIN 23011-7 DIN 23011-7 Bbl 1 DIN 23011-8

FB Analysis of Raw Material/Coal preparation 0

01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 5: Size reduction and dissociation (9) 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 6: Homogenizing (11) 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - P art 7: Involuntary breakage (8) 10.05 Preparation of hard coal - Flocculants for process water - Terms, requirements, verification (12) 05.88 Preparation of hard coal - F lotation agents - Terms, requirements, verification (8) 03.90 Preparation of hard coal - Medium solids - Terms, requirements, testing (9) 08.85 Preparation of hard coal - Simulation of processes and material-flows - Part 1: Homogenizing (7) 12.88 Preparation of hard coal - Simulation of processes and material-flows - Part 2: Separations (8) 02.89 Preparation of hard coal; preparation plants - P art 2: Flowsheets (10) 10.92 Preparation of hard coal; preparation-plants - Part 3: Graphical symbols for flowsheets (14) 11.06 Preparation of hard coal; preparation plants Part 4: Technical agreements with regard to the fixation of guaranties (7) 11.06 Preparation of hard coal - Preparation plants - Part 5: Process control (9) 12.04 Preparation of hard coal - Preparation plants - Part 6: Equipment and operation of a plant laboratory (9) 11.06 Preparation of hard coal - P reparation plants - Part 7: Equipment monitoring (7) 12.09 Preparation of hard coal - P reparation plants - Part 7: Equipment monitoring; Supplement 1: Means of application for the standard (7) 02.08 Preparation of hard coal - Preparation plants - Part 8: Process technical requirements on preparation equipment (13)


Page 28 of 45


FB Cokery, Briquettes 09

09 Cokery, Br iqu ettes NA 008-09-01 AA Bri cks for c oke ovens

DIN 1089-1 DIN 1089-2 DIN 1089-3

02.95 Refractories for use in coke ovens - Part 1: Silica bricks - Requirements and testing (6) 02.95 Refractories for use in coke ovens - Part 2: Fireclay bricks - Requirements and testing (7) 10.90 Refractories for use in coke ovens; mortar for silica and fireclay bricks; requirements and testing (7)


Page 29 of 45


FB Open Cast Mining 10

10 Open Cast Mining NA 008-10-01 AA Excavators, spreaders and auxiliary equipment in opencast lignite mines

DIN 5651 DIN 22261-1 E DIN 22261-1 DIN 22261-2 DIN 22261-3 DIN 22261-4 DIN 22261-5 DIN 22261-6 DIN 43120 DIN 43139 DIN 43153 DIN 43160

11.79 Brake block holders and brake block keys for composite brake blocks on rail vehicles; technical specifications (4) /FABERG co-author/ 12.04 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 1: Construction, commissioning and monitoring (10) 01.10 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 1: Construction, commissioning and monitoring (10) 12.06 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 2: Calculation principles (32) 11.06 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 3: Welded connections, joint types, classification, test instruction (14) 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 4: Hoisting winch brakes (6) 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 5: Slewing brakes and overload protecting devices (7) 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 6: Examination of ropes and rope end fittings (7) 09.52 Electric railway vehicles; bow slipper holder for contact wire clamps (4) /FABERG co-author/ 12.67 Drums for contact-wires for electric traction (4) /FABERG co-author/ 01.68 Thimble with clevis for overhead equipment (4) /FABERG co-author/ 01.68 Eye and clevis for overhead equipment; connecting dimensions (4) /FABERG co-author/

NA 008-10-02 AA Belt conveyors in opencast lignite mining

DIN EN 14658

06.10 Continuous handling equipment and systems - General safety requirements for continuous handling equipment for opencast lignite mining; German version EN 14658:2005+A1:2010 (15)


Page 30 of 45


FB Mine Plans 11

11 Mine Plans NA 008-11-01 AA Mine surveying

DIN 18723-7 DIN 21961

07.90 Field procedure for precision testing of surveying instruments - Part 7: Gyroscopes 06.00 Mine surveying - Slip-on pivots, slip-on caps for suspension theodolites Connecting dimensions (5)

NA 008-11-01-01 AK B asic s

DIN 21901 DIN 21901 Bbl 1 DIN 21901 Bbl 2 DIN 21901 Bbl 3 DIN 21901-2 DIN 21902 DIN 21902-2 DIN 21903 DIN 21904 DIN 21905 DIN 21906 DIN 21906 Bbl 1 DIN 21906 Bbl 2 DIN 21907 DIN 21908

02.84 Mine plans; structure and list of standards; general principles (5) 09.06 Mine plans - Structure and list of standards -Supplement 1: Contents (6) 09.06 Mine plans - Structure and list of standards - Supplement 2: List of abbreviations (18) 07.02 Mine plans; structure and list of standards; index 11.94 Mine plans - Structure and list of standards - Part 2: Interface for EDP based transfer of symbols of mining - Specific mapping (12) 10.99 Mine plants - Structure of mining specific plans (7) 08.08 Mine plants - Structure of mining specific plans - Part 2: Completion of mine plans (11) 10.95 Mine plans - Sizes and foldings (8) 01.94 Mine plants; lettering (5) 11.93 Mine plants; drawing principles (5) 08.90 Mine plans - Subdivision of sheets (9) 11.91 Mine plans; subdivision of sheets; survey (19) 01.94 Mine plans; subdivision of sheets; survey (14) 04.03 Mine plans - Graphic design of sheets (12) 01.94 Mine plans - Colours (8)

NA 008-11-01-02 AK Objects on t he surf ace, open pit m ines

DIN 21909 DIN 21910 DIN 21911 DIN 21912-1 DIN 21912-2 E DIN 21912-2

02.02 06.02 03.08 01.06 03.01 11.09

Mine plans - Survey points and lines (9) Mine plans - Titles and boundaries (12) Mine plans; objects on the surface and contour lines (12) Mine plans - Opencast mining - Part 1: General requirements (12) Mine plans - Open cast mining - Part 2: Reconstruction (8) Mine plans - Open cast mining - Part 2: Reconstruction (11)

NA 008-11-01-03 AK Geolog ic symb ols and terms

DIN 21918-1 DIN 21918-2 DIN 21919-1 DIN 21919-2 DIN 21919-3 DIN 21920-1 DIN 21920-2 DIN 21920-3 DIN 21920-4

10.99 08.04 01.00 12.08 11.01 11.88 04.96 04.96

Mine plans - Mineral deposits - Part 1: Terms, classification (6) Mine plans - Mineral deposits - Part 2: Thicknesses (10) Mine plans - Stratigraphy - Part 1: General classification (7) Mine plans - Stratigraphy - Part 2: Regional and local subdivisions; Hard coal (8) Mine plans - Stratigraphy - Part 3: Regional and local subdivisions; Lignite (9) Mine plans - Petrography - Part 1: Generally applicable symbols - Sediments (9) Mine plans - Petrography - Part 2: Magmatites (10) Mine plans - Petrography - Part 3: Metamorphic and other lithogenetic phenomena (10) 04.96 Mine plans - Petrography - Part 4: Minerals (6)


Page 31 of 45

Register of Mining Standards 2010-12 DIN 21920-5 DIN 21920-7 DIN 21921 DIN 22011 DIN 22012 DIN 22015

FB Mine Plans 11

11.94 04.96 04.96 11.93

Mine plans - Petrography - Part 5: Hard coal mining (12) Mine plans - Petrography - Part 7: Potash and rock salt mining (7) Mine plans - Tectonic elements and figure of strata (13) Investigations of the raw material in hard-coal-mining - Treatment of exploratory drillings (17) 01.94 Investigations of the raw material in hard-coal-mining - Macropetrographic classification and topographic survey of hard-coal and host rock (8) 10.93 Investigations of the raw material in hardcoal-mining - Macroscopic classification and description of overburden rock (9)

NA 008-11-01-04 AK Special representations

DIN 21913-11 DIN 21916-1 DIN 21916-2 DIN 21916-3 E DIN 21916-3 DIN 21917 DIN 21917-2

01.00 Mine plans - Deep mining - Part 11: Geometrical dimensions in underground workings (7) 02.07 Mine plans - Operational safety - Part 1: Ventilation system and meteorology (13 02.10 Mine plans - Operational safety - Part 2: Fire prevention on the surface (12) 06.93 Mine plans; operational safety; fire prevention under the surface (10) 11.09 Mine plans - Operational safety - P art 3: Fire prevention under the surface (11) 02.99 Mine plans - Strata and ground movements (13) 03.02 Mine plans - Strata and ground movements - Part 2: Geomechanical measuring points (7)

NA 008-11-01-05 AK Mine workings

DIN 21913-1 DIN 21913-1 Bbl 1 DIN 21913-2 DIN 21913-3 DIN 21913-4 DIN 21913-6 E DIN 21913-7

02.92 Mine plans; deep mining; underground workings (19) 02.92 Mine plans; underground working; storage and final deposition in mine workings (33) 02.09 Mine plans - Deep mining - Part 2: Extraction, stowage and deposit (14) 02.08 Mine plans - Deep mining - Part 3: Closure of underground workings (8) 02.09 Mine plans; deep mining; Part 4: hazardous zones, zones of protective measures (11) 07.04 Mine plans - Deep mining - Part 6: Safekeeping of mining produced hollows (7) 11.10 Mine plans - Deep mining - Part 7: Shaft plan (11)

NA 008-11-01-06 AK Dri lli ng, caverns, s torage, final d eposit ion

DIN 21914-1 DIN 21914-2

10.05 Mine plans - Drilling and cavern - Part 1: Drilling (15) 02.99 Mine plans - Drilling and cavern - Part 2: Brine caverns (10)


Page 32 of 45


FB Fuels 12

12 Fuels NA 008-12-01 AA Gaseous fuels

DIN 1340 DIN 1340 Bbl 1 DIN 1871 DIN EN 1918-1 DIN EN 1918-2 DIN EN 1918-3 DIN EN 1918-4 DIN EN 1918-5 DIN ISO 5275 DIN EN ISO 6141 DIN ISO 6142 DIN EN ISO 6143 DIN ISO 6144 DIN ISO 6146 DIN EN ISO 6326-3

DIN EN ISO 6326-5 DIN EN ISO 6570 DIN EN ISO 6974-1 E DIN EN ISO 6974-1

12.90 Gaseous fuels and other gases - Types, constituents, application (7) /FABERG co-author/ 12.90 Gaseous fuels and other gases - Types, constituents, application - Remarks on the production (5) /FABERG co-author/ 05.99 Road marking materials - Physical properties; German version EN 1871:2000 (13) /FABERG co-author/ 07.98 Gas supply systems - Underground gas storage - Part 1: Functional recommendations for storage in aquifers; German version EN 1918-1:1998 (9) /FABERG co-author/ 07.98 Gas supply systems - Unterground gas storage - Part 2: Functional recommendations for storage in oil and gas fields; German version EN 19182:1998 (8) /FABERG co-author/ 07.98 Gas supply systems - Underground gas storage - Part 3: Functional recommendations for storage in solution-mined salt cavities; German version EN 1918-3:1998 (10) /FABERG co-author/ 07.98 Gas supply systems - Underground gas storage - Part 4: Functional recommendations for storage in rock caverns; German version EN 19184:1998 (7) /FABERG co-author/ 07.98 Gas supply systems - Underground gas storage - Part 5: Functional recommendations for surface facilities; German version EN 1918-5:1998 (6) /FABERG co-author/ 10.05 Petroleum products and hydrocarbon solvents - Detection of thiols and other sulfur species - Doctor test (ISO 5275:2003) (6) /FABERG co-author/ 11.06 Gas analysis - Requirements for certificates for calibration gases and gas mixtures (ISO 6141:2000); German version EN ISO 6141:2006 (8) /FABERG coauthor/ 05.85 Gas analysis - Preparation of calibration gas mixtures - Weighing methods (7) /FABERG co-author/ 11.06 Gas analysis - Comparison methods for determining and checking the composition of calibration gas mixtures (ISO 6143:2001); German version EN ISO 6143:2006 (15) /FABERG co-author/ 05.85 Gas analysis; preparation of calibration gas mixtures; static volumetric methods (10) /FABERG co-author/ 04.83 Gas analysis; preparation of calibration gas mixtures; manometric method (12) /FABERG co-author/ 04.98 Natural gas - Determination of sulfur compounds - Part 3: Determination of hydrogen sulfide, mercaptan sulfur and carbonyl sulfide sulfur by potentiometry (ISO 6326-3:1989); German version EN ISO 6326-3:1997 (7) /FABERG coauthor/ 04.98 Natural gas - Determination of sulfur compounds - Part 5: Lingener combustion method (ISO 6326-5:1989); German version EN ISO 6326-5:1997 (9) /FABERG co-author/ 12.04 Natural gas - Determination of potential hydrocarbon liquid content - Gravimetric methods (ISO 6570:2001); English version EN ISO 6570:2004 (13) /FABERG co-author/ 06.02 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 1: Guidelines for tailored analysis (ISO 6974-1:2000); German version EN ISO 6974-1:2001 (12) /FABERG co-author/ 03.10 Natural gas - Determination of composition and associated uncertainty by gas chromatography - Part 1: General guidelines and calculation of composition (ISO/DIS 6974-1:2010); German version prEN ISO 6974-1:2010 (20) /FABERG co-author/


Page 33 of 45


FB Fuels 12

07.02 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 2: Measuring- system characteristics and statistics for processing of data (ISO 6974-2:2001); German version EN ISO 6974-2:2002 / Note: Applies only in conjunction with DIN ISO 6974-1 (2002- 06) (13) /FABERG co-author/ E DIN EN ISO 6974-2 03.10 Natural gas - Determination of composition and associated uncertainty by gas chromatography - Part 2:Uncertainty calculations (ISO/DIS 6974-1:2010); German version prEN ISO 6974-2:2010 (20) /FABERG co-author/ DIN EN ISO 6974-3 06.02 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two packed columns (ISO 6974-3:2000); German version EN ISO 6974-3:2001 / Note: Applies only in conjunction with DIN EN ISO 6974-1 and DIN EN ISO 6974-2 (11) /FABERG co-author/ DIN EN ISO 6974-4 06.02 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 4: Determination of nitrogen, carbon dioxide and C1- to C5- and C6+hydrocarbons for a laboratory and on-line measuring system using two columns (ISO 6974-4:2000); German version EN ISO 6974-4:2001 / Note: Applies only in conjunction with DIN EN ISO 6974-1 and DIN EN ISO 6974-2 (10) /FABERG co-author/ DIN EN ISO 6974-5 06.02 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 5: Determination of nitrogen, carbon dioxide and C1- to C5- and C6+hydrocarbons for a laboratory and on-line measuring system using two columns (ISO 6974-5:2000); German version EN ISO 6974-5:2001 (11) /FABERG co-author/ DIN EN ISO 6974-6 08.05 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 6: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and C1 to C8 hydrocarbons using three capillary columns (ISO 6974-6:2002); German version EN ISO 6974-6:2005 (12) /FABERG co-author/ DIN EN ISO 6975 09.05 Natural gas - Extended analysis - Gas-chromatographic method (ISO 6975:1997); German version EN ISO 6975:2005 (14) /FABERG co-author/ DIN EN ISO 6975/B1 09.08 Natural gas - Extended analysis - Gas-chromatographic method (ISO 6975:1997); German version EN ISO 6975:2005, Corrigendum to DIN EN ISO 6975:2005-09 (99) /FABERG co-author/ 09.05 Natural gas - Calculation of calorific values, density, relative density and Wobbe DIN EN ISO 6976 index form composiotion (ISO 6976:1995 +Corrigendum 1:1997, Corrigendum 2:1997, Corrigendum 3:1999); German version EN ISO 6976:2005 (22) /FABERG co-author/ DIN EN ISO 6978-1 09.05 Natural gas - Determination of mercury - Part 1: Sampling of mercury by chemisorption on iodine (ISO 6978-1:2003); German version EN ISO 69781:2005 (12) /FABERG co-author/ DIN EN ISO 6978-2 09.05 Natural gas - Determination of mercury - Part 2: Sampling of mercury by amalgamation on gold/platinum alloy (ISO 6978-2:2003); German version EN ISO 6978-2:2005 (12) /FABERG co-author/ DIN EN ISO 10101-1 07.98 Natural gas - Determination of water by the Karl Fischer method - Part 1: Introduction (ISO 10101-1:1993); German version EN ISO 10101-1:1998 (6) /FABERG co-author/ DIN EN ISO 10101-2 07.98 Natural gas - Determination of water by the Karl Fischer method - Part 2: Tritation procedure (ISO 10101-2:1993); German version EN ISO 10101-2:1998 (8) /FABERG co-author/ DIN EN ISO 10101-3 07.98 Natural gas - Determination of water by the Karl Fischer method - Part 3: Coulometric procedure (ISO 10101-3:1993); German version EN ISO 101013:1998 (8) /FABERG co-author/ DIN EN ISO 10723 02.03 Natural gas - Performance evaluation for on-line analytical systems (ISO 10723:1995); German version EN ISO 10723:2002 (19) /FABERG co-author/ 02.03 Natural gas - Determination of water content at high pressure (ISO DIN EN ISO 11541 11541:1997); German version prEN ISO 11541:2002 (7) /FABERG co-author/ DIN EN ISO 6974-2


Page 34 of 45

Register of Mining Standards 2010-12 DIN EN ISO 12213-1 DIN EN ISO 12213-2 DIN EN ISO 12213-3 DIN 12473-1 DIN 12473-2 DIN EN ISO 14111 DIN EN ISO 18453 BB 22061-1 BB 22061-2 BB 22061-3 DIN 51400-4 DIN 51851 DIN 51853 E DIN 51853/A1 DIN 51854 DIN 51855-1 E DIN 51855-1/A1 DIN 51855-4 DIN 51855-6 DIN 51855-7 DIN 51855-8

DIN 51857 DIN 51859

FB Fuels 12

01.10 Natural gas - Calculation of compression factor - Part 1: Introduction and guidelines (ISO 12213-1:2006); German version EN ISO 12213-1:2009 (11) /FABERG co-author/ 01.10 Natural gas - Calculation of compression factor - Part 2: Calculation using molar composition analysis (ISO 12213-2:2006); German version EN ISO 122132:2009 (16) /FABERG co-author/ 01.10 Natural gas - Calculation of compression factor - Part 3: Calculation using physical properties (ISO 12213-3:2006); German version EN ISO 12213-3:2009 (17) /FABERG co-author/ 04.76 Laboratory glassware - gas sampling tubes with straight bore stopcocks (4) /FABERG co-author/ 04.76 Laboratory glassware - gas sampling tubes with V-bore stopcocks (4) /FABERG co-author/ 06.00 Naturalgas - Guidelines to traceability in analyses (ISO 14111:1997); German version EN ISO 14111:1999 (13) /FABERG co-author/ 01.06 Natural gas - Correlation between water content and water dew point (ISO 18453:2004); German version prEN 18453:2005 (13) /FABERG co-author/ 04.82 Steinkohlenbergbau - Gase unter Tage - Anwendungsbereich, Zweck, Begriffe und Allgemeines (1) 04.82 Steinkohlenbergbau - Gase unter Tage - Probenahme (4) 04.82 Steinkohlenbergbau - Gase unter Tage - Analyse nach physikalischen Verfahren im Laboratorium (2) 04.00 Testing of mineral oils and fuels - Determination of sulfur content (total sulfur) Part 4: Combustion according to the Lingener method, visual titration, turbidmetric-titration (6) /FABERG co-author/ 04.80 Testing of gaseous fuels and other gases; calculation of reduced gas volume (4) /FABERG co-author/ 11.95 Testing of fuel gases - Sampling (8) /FABERG co-author/ 01.09 Testing of fuel gases - Sampling, Amendment A 1 (4) /FABERG co-author/ 09.93 Testing of gaseous fuels and other gases; determination of ammonia content (5) /FABERG co-author/ 05.99 Testing of gaseous fuels and other gases - Determination of the content of sulphur compounds - Part 1: Field of application, terms (5) /FABERG co-author/ 12.09 Testing of gaseous fuels and other gases - Determination of the content of sulphur compounds - Part 1: Field of application, terms; Amendment A1 (4) /FABERG co-author/ 06.95 Testing of gaseous fuels and other gases - Determination of sulphur compounds content - Part 4: Content of hydrogen sulfide, zinc acetate method (5) /FABERG co-author/ 09.00 Testing of gaseous fuels and other technical gases - Determination of sulfur compounds content - Part 6: Content of hydrogen sulfide, mercaptan sulfur and carbonylsulfide sulfur; potentiometric method (6) /FABERG co-author/ 12.86 Testing of gaseous fuels and other gases; determination of the content of sulfur compounds; gaschromatographic determination of the content of odoriferous sulfur compounds using an electrochemical detector (5) /FABERG co-author/ 06.97 Testing of gaseous fuels and other gases - Determination of sulfur compounds content - Part 8: Gaschromatographic determination of dihydrogen sulfide, carbonyl sulfide and other sulfur compounds using specific detectors (7) /FABERG co-author/ 03.97 Gaseous fuels and other gases - Calculation of calorific value, density, relative density and Wobbe index of pure gases and gas mixtures (9) /FABERG coauthor/ 06.90 Testing of gaseous fuels and other gases; gravimetric determination of the content of condensate as a function of pressure and temperature (5) /FABERG co-author/


Page 35 of 45

Register of Mining Standards 2010-12 DIN 51862 DIN 51863-1 DIN 51863-2 DIN 51864 DIN 51865-1 DIN 51865-2 DIN 51865-3 DIN 51869 DIN 51870 DIN 51871 DIN 51872-4 DIN 51872-5 DIN 51896-1 DIN 51896-2

FB Fuels 12

09.82 Testing of gaseous fuels and other gases; determination of naphthalene content (crude naphthalene) (5) /FABERG co-author/ 09.83 Testing of gaseous fuels and other gases; determination of hydrogen cyanide content; nickel carbonate method (6) /FABERG co-author/ 09.83 Testing of gaseous fuels and other gases; determination of hydrogen cyanide content; bromide cyanogen method (5) /FABERG co-author/ 09.86 Testing of gaseous fuels and other gases; determination of nitrogen monoxide content; Saltzman method (5) /FABERG co-author/ 09.98 Testing of gaseous fuels and other gases - Determination of mercury content Part 1: Chemisorption on Iodine, atomic absorption spectrometry (AAS) (6) /FABERG co-author/ 10.00 Testing of gaseous fuels and other gases - Determination of mercury content Part 2: Combustion using the modified Lingener method; Atomic absorption spectrometry (AAS) (6) /FABERG co-author/ 02.98 Testing of gaseous fuels and other gases - Determination of mercury content Part 3: Absorption in solutions, atomic absorption spectrometry (AAS) (6) /FABERG co-author/ 09.00 Testing of gaseous fuels and other gases; determination of the main components, general statements (5) /FABERG co-author/ 04.81 Testing of gaseaus fuels and other gases; determination of relative density according to the balance method and calculation of density (6) /FABERG coauthor/ 12.85 Testing of gaseous fuels and other technical gases; determination of dew point of water vapour; method of means of cooled mirror (5) /FABERG co-author/ 06.90 Testing of gaseous fuels and other gases; determination of the components; gaschromatographic procedure (6) /FABERG co-author/ 08.96 Testing of gaseous fuels and other gases - Determination of the components Part 5: Capillary gaschromatographic procedure (8) /FABERG co-author/ 10.91 Gas analysis; quantities of compositions, compressibility factor; basis (7) /FABERG co-author/ 09.94 Gas analysis - Quantities of composition, compressibility factor - Part 2: Application (10) /FABERG co-author/

NA 008-12-02 AA Testi ng of sol id f uels

DIN 22022-1 DIN 22022-2 DIN 22022-3 DIN 22022-4 DIN 22022-5 DIN 22022-6 DIN 51700 DIN 51701-1 DIN 51701-2 DIN 51701-3 DIN 51701-4

02.01 Solid fuels - Determination of contents of trace elements - Part 1: General rules, sampling and sample preparation; Preparation of samples for the analyses (dissolution method) (7) 02.01 Solid fuels - Determination of contents of trace elements - Part 2: ICP-OES (5) 02.01 Solid fuels - Determination of trace elements - Part 3: AAS-flame method (5) 02.01 Solid fuels - Determination of contents of trace elements - P art 4: Atomic absorption spectrometry applying the flameless hydride system or the coldvapour-method (5) 02.01 Solid fuels - Determination of trace elements - Part 5: Atomic absorption spectrometry applying the electrothermal atomization (5) 12.01 Solid fuels - Determination of trace elements - Part 6: Evaluation and declaration of results (7) 07.10 Testing of solid fuels - Generalities and index of methods of test (13) 12.07 Testing of solid fuels - Sampling and sample preparation - Part 1: Definitions (6) 09.06 Testing of solid fuels - Sampling and sample preparation - Part 2: Sampling (12) 09.06 Testing of solid fuels - Sampling and sample preparation - Part 3: Sample preparation (9) 09.06 Testing of solid fuels - Sampling and sample preparation - Part 4: Equipment (10)


Page 36 of 45

Register of Mining Standards 2010-12 DIN 51701-5 DIN 51705 DIN 51717 DIN 51718 DIN 51719 DIN 51720 DIN 51721 DIN 51722-1 DIN 51723 DIN 51724-1 DIN 51724-2 DIN 51724-3 DIN 51725 DIN 51726 DIN 51727 DIN 51729-8 DIN 51729-10 E DIN 51729-10 DIN 51729-11 DIN 51730 DIN 51731 DIN 51732 DIN 51733 DIN 51734 DIN 51735 DIN 51739 DIN 51741 DIN 51742 DIN 51900-1/B1 DIN 51900-1 DIN 51900-2

FB Fuels 12

03.08 Testing of solid fuels - Sampling and sample preparation - Part 5: Testing of precision (12) 06.01 Testing of solid fuels - Determination of the bulk density of solid fuels (5) 07.94 Testing of solid fuels; determination of mechanical strength of coke (6) 06.02 Testing of solid fuels - Determination of the water content and the moisture of analysis sample (6) 07.97 Testing of solid fuels - Solid mineral fuels - Determination of ash content (5) 03.01 Testing of solid fuels - Determination of volatile matter content (7) 08.01 Testing of solid fuels - Determination of carbon content and hydrogen content Radmacher-Hoverath method (6) 07.90 Testing of solid fuels; determination of nitrogen content; semi-micro Kjeldahl method (5) 06.02 Testing of solid fuels - Determination of fluorine content (7) 06.99 Testing of solid fuels - Determination of sulfur content - Part 1: Total sulfur (7) 06.99 Testing of solid fuels - Determination of sulfur content - Part 2: Species (7) 03.08 Testing of solid fuels - Determination of sulfur content - Part 3: Instrumental methods (6) 06.04 Testing of solid fuels - Determination of the phosphorus content (7) 06.04 Testing of solid fuels - Determination of the carbonate carbon dioxide content (7) 06.01 Testing of solid fuels - Determination of chlorine content (6) 05.01 Solid fuels - Determination of chemical composition of fuel ash - P art 8: Determination of soda and potash (Na<(Index)2>O, K<(Index)2>O) contents (5) 05.96 Testing of solid fuels - Determination of chemical composition of fuel ash - Part 10: X-Ray fluorescence analysis (5) 03.10 Testing of solid fuels - Determination of chemical composition of fuel ash - Part 10: X-Ray fluorescence analysis (8) 11.98 Testing of solid fuels - Determination of chemical composition of fuel ash - Part 11: Determination by inductively coupled plasma emission spectrometry (ICPOES) (5) 09.07 Testing of solid fuels - Determination of fusibility of fuel ash (10) 10.96 Testing of solid fuels - Compressed untreated wood - Requirements and testing (5) /FABERG co-author/ 08.07 Testing of solid mineral fuels - Determination of total carbon, hydrogen and nitrogen - Instumental methods (8) 12.08 Testing of solid mineral fuels - Ultimate analysis and calculation of oxygen content (6) 12.08 Testing of solid mineral fuels - Proximate analysis and calculation of fixed carbon (6) 02.09 Testing of solid mineral fuels - Determination of plastic properties of coal using the Gieseler plastometer (9) 05.98 Testing of solid fuels - Determination of the dilatation of coal (8) 10.98 Testing of solid fuels - Determination of the crucible swelling number of coal (6) 07.01 Testing of solid fuels - Determination of Hardgrove grindability index of hard coal (7) 02.04 Corrigenda to DIN 51900-1:2000-04 04.00 Testing of solid and liquid fuels - Determination of gross calorific value by the bomb calorimeter and calculation of net calorific value - Part 1: Principles, apparatus, methods (12) 05.03 Testing of solid and liquid fuels - Determination of the gross calorific value by the bomb calorimeter and calculation of the net calorific value - Method using isoperibol or static jacket calorimeter (8)


Page 37 of 45

Register of Mining Standards 2010-12 DIN 51900-3

FB Fuels 12

01.05 Testing of solid and liquid fuels - Determination of the gross calorific value by the bomb calorimeter and calculation of net calorific value - Part 3: Method Using Adiabatic J acket (8)


Page 38 of 45


FB Cables, Telecontrol and Other Electrical Equipment 1

14 Cables, Telecont rol and Other Electric al Equipment 14 Cables, telecontrol and other electrical equipment

BB 22000-1 BB 22000-2 BB 22000-3 BB 22442-1 BB 22442-2 BB 22443 BB 22444-1 BB 22444-2 BB 22444-3 BB 22444-4 BB 22444-4 Bbl 1 BB 22444-4 Bbl 2 BB 22444-4 Bbl 3 BB 22445 BB 22446 BB 22450-1 BB 22450-2 BB 22450-2/A1 BB 22450-3 BB 22450-4 BB 22450-5 BB 22450-6 BB 22450-7 BB 22450-8 DIN 43620-5

11.75 02.76 02.76 03.03

Größen und Einheiten - Teil 1: Einheiten - Allgemeine Grundlagen (3) Größen und Einheiten - Teil 2: Masse, Kraft, Gewicht (1) Größen und Einheiten - Teil 3: Temperatur, Druck (2) Elektromagnetische Verträglichkeit für Anlagen im Steinkohlenbergbau - Teil 1: Grundlagen (4) 03.03 Elektromagnetische Verträglichkeit für Anlagen im Steinkohlenbergbau - Teil 2: Störaussendungs- und Störfestigkeits-Grenzwerte (4) 08.88 Geräte und Anlagen der Fernwirktechnik - Dokumentation von Softwaresystemen (4) 02.76 Geräte und Anlagen der Fernwirktechnik - Begriffe (2) 10.82 Geräte und Anlagen der Fernwirktechnik - Anforderung und Prüfung (3) 07.87 Geräte und Anlagen der Fernwirktechnik - Schnittstellen (3) 07.87 Geräte und Anlagen der Fernwirktechnik - Standardaufbau einer Telegrammschnittstelle zwischen Fernwirkstation und Prozeßrechner (3) 07.87 Geräte und Anlagen der Fernwirktechnik - Standard für die serielle Datenübertragung im Nahbereich (2) 07.87 Geräte und Anlagen der Fernwirktechnik - Ablauf der Datenübertragung (1) 07.87 Geräte und Anlagen der Fernwirktechnik - Ablaufbeispiel der Datenübertragung (1) 10.73 Wassergekühlte polumschaltbare Drehstrommotoren, Bauform B5 Anbaumaße und Zuordnung der Leistungen bei Ausführung in Zündschutzart (Sch) d (1) 05.87 Geräte und Anlagen der Fernwirktechnik - Frequenzbereiche für Funkanlagen (2) 06.88 Grubenkabel für Fernmelde- und Informationsanlagen - Auswahl für den Steinkohlenbergbau unter Tage (2) 06.88 Leitungen für Fernmelde- und Informationsanlagen - Auswahl für den Steinkohlenbergbau unter Tage (2) 12.00 Leitungen für Fernmelde- und Informationsverarbeitungsanlagen - Auswahl für den Steinkohlenbergbau unter Tage - Änderung 1 (2) 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 3: Bewehrte Leitung L-2YYQY (blau) (4) 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 4: Zugfeste, geschirmte Leitung L2Y(C)Y(ZG)Y (blau) (4) 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 5: Zugfeste, geschirmte Leitungen L2YYC(ZG)Y (blau) (4) 06.99 Grubenkabel für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 6: Bewehrtes Grubenkabel G-2YYYBY (blau) mit Paaren (4) 06.99 Grubenkabel für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 7: Bewehrtes Grubenkabel G-2YY(Z)Y (blau) mit Paaren (4) 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 8: Zugfeste Leitung L-YY(ZG)Y (blau) (4) 06.86 Low-voltage high-rupturing capacity fuses with blade contacts; LV HRC fuse links for AV 1000 V (5) /FABERG co-author/


Page 39 of 45


FB Solid mineral fuels ISO/TC 27

ISO/TC 27 Solid mineral fuels ISO/TC 27 Solid mineral f uels

ISO 502 ISO 1953

02.82 Coal - Determination of caking power - Gray-King coke test 07.94 Hard coal - Size analysis by sieving

ISO/TC 27/WG 18 Classifi cation of coals

ISO 11760

02.05 Classification of coals

ISO/TC 27/WG 19 Petrogr aphic analysi s of bi tumi nous coal and anthraci te

ISO 7404-1 ISO 7404-2 ISO 7404-3 ISO 7404-4 ISO 7404-5

10.94 Methods for the petrographic analysis of bitumious coal and anthracite - Part 1: Vocabulary 10.09 Methods for the petrographic analysis of coals - Part 2: Methods of preparing coal samples 10.09 Methods for the petrographic analysis of coals - Part 3: Method of determining maceral group composition 12.88 Methods for the petrographic analysis of bitumious coal and anthracite - Part 4: Method of determining microlithotype, carbominerite and minerite composition 10.09 Methods for the petrographic analysis of coals - Part 5: Method of determining microscopically the reflectance of vitrinite

ISO/TC 27/SC 1 Coal preparation - Termin olog y and p erform ance

ISO 561 ISO 923 ISO 924 ISO 1213-1 ISO 1213-2

12.89 05.00 12.89 12.93 04.92

ISO 7936

04.92

ISO 8833 ISO 8858-1 ISO 8858-2 ISO 8858-3 ISO 10086-1

11.89 09.90 08.04 08.04 06.00

ISO 10086-2

01.04

ISO 10752 ISO 10753

05.94 02.94

ISO 15117-1 ISO 20905 ISO 23499

05.04 07.04 06.08

Coal preparation plant - Graphical symbols Coal cleaning equipment - Performance evaluation Coal preparation plant - Principles and conventions for flowsheets Solid mineral fuels - Vocabulary - Part 1: Terms relating to coal preparation Solid mineral fuels - Vocabulary - Part 2: Terms relating to sampling, testing and analysis Hard coal - Determination and presentation of float and sink characteristics General directions for apparatus and procedures Magnetite for use in coal preparation - Test methods Hard coal - Froth flotation testing - Part 1: Laboratory procedure Hard coal - F roth flotation testing - Part 2: Sequential evaluation Hard coal - Froth flotation testing - Part 3: Release evaluation Coal - Methods for evalution flocculants for use in coal preparation - Part 1: Basic parameters Coal - Methods for evaluating flocculants for use in coal preparation - Part 2: Flocculants as filter aids in rotary vacuum filtration systems Coal sizing equipment - Performance evaluation Coal preparation plant - Assessment of the liability to breakdown in water of materials associated with coal seams Coal flow properties - Part 1: Bin flow Coal preparation - Determination of dust/moisture relationship for coal Coal - Determination of bulk density

ISO/TC 27/SC 3 Coke

ISO 556 ISO 567 ISO 616

11.80 Coke (greater than 20 mm in size) - Determination of mechanical strength 07.95 Coke - Determination of bulk density in a small container 11.95 Coke - Determination of shatter indices


Page 40 of 45

Register of Mining Standards 2010-12 ISO 728 ISO 1013 ISO 1014 ISO 2325 ISO 18894


11.95 Coke (nominal top size greater than 20 mm) - Size analysis by sieving 07.95 Coke - Determination of bulk density in a large container 09.85 Coke - Determination of true relative density, apparent relative density and porosity 02.86 Coke - Size analysis (Nominal top size 20 mm or less) 04.06 Coke - Determination of coke reactivity index (CRI) and coke strength after reaction (CSR)

ISO/TC 27/SC 4 Sampli ng

ISO 5069-1 ISO 5069-2 ISO 9931 ISO 21398

11.83 Brown coals and lignites - P rinciples of sampling - Part 1: Sampling for determination of moisture content and for general analysis 12.83 Brown coals and lignites - P rinciples of sampling - Part 2: Sample preparation for determination of moisture content and for general analysis 12.91 Coal - Sampling of pulverized coal conveyed by gases in direct fire coal systems 06.07 Hard coal and coke - Guidance to the inspection of mechanical sampling systems

ISO/TC 27/SC 4/WG 1 Sampli ng of coal

ISO 13909-1 ISO 13909-2 ISO 13909-3 ISO 13909-4

12.01 Hard coal and coke - Mechanical sampling - Part 1: General introduction 12.01 Hard coal and coke - Mechanical sampling - Part 2: Coal - Sampling from moving streams 12.01 Hard coal and coke - Mechanical sampling - Part 3: Coal - Sampling from stationary lots 12.01 Hard coal and coke - Mechanical sampling - Part 4: Coal - Preparation of test samples

ISO/TC 27/SC 4/WG 2 Sampling of coke

ISO 13909-5 ISO 13909-6

12.01 Hard coal and coke - Mechanical sampling - Part 5: Coke - Sampling from moving streams 12.01 Hard coal and coke - Mechanical sampling - Part 6: Coke - Preparation of test samples

ISO/TC 27/SC 4/WG 5 Methods for test for bias

ISO 13909-7 ISO 13909-8

12.01 Hard coal and coke - Mechanical sampling - Part 7: Methods for determining the precision of sampling, sample preparation and testing 12.01 Hard coal and coke - Mechanical sampling - Part 8: Methods of testing for bias

ISO/TC 27/SC 4/WG 6 Sampling of coal seams

ISO 14180

08.98 Solid mineral fuels - Guidance on the sampling of coal seams

ISO/TC 27/SC 4/WG 7 Manual Sampli ng

ISO 18283 ISO 18283:2006/Cor 1

09.06 Hard coal and coke - Manual sampling 04.09 ISO 18283 Technical Corrigendum 1

ISO/TC 27/SC 4/WG 8 Sampling of coal slurries

ISO 20904

10.06 Hard coal - Sampling of slurries

ISO/TC 27/SC 5 Methods of analysis

ISO 12900 ISO 23380

12.97 Hard coal - Determination of abrasiveness 10.08 Selection of methods for the determination of trace elements in coal


Page 41 of 45



ISO/TC 27/SC 5/WG 1 Moisture, volatile matter and ash

ISO 562 ISO 579 ISO 589 ISO 687

06.10 12.99 11.08 06.10

ISO 1018 ISO 1170 ISO 1171 ISO 11722

11.75 10.08 06.10 05.99

ISO 17246

06.10

Hard coal and coke - Determination of volatile matter Coke - Determination of total moisture Hard coal - Determination of total moisture Solid mineral fuels - Coke - Determination of moisture in the general analysis test sample Hard coal - Determination of moisture-holding capacity Coal and coke - Calculation of analyses to different bases Solid mineral fuels - Determination of ash Solid mineral fuels - Hard coal - Determination of moisture in the general analysis test sample by drying in nitrogen Coal - Proximate analysis

ISO/TC 27/SC 5/WG 2 Carbon, h ydrog en, nitr ogen, oxy gen and s ulf ur

ISO 157 ISO 334 ISO 351/COR 1 ISO 351 ISO 587 ISO 609 ISO 609/COR 1 ISO 625 ISO 625/COR 1 ISO 925 ISO 1994 ISO 17247 ISO 17247/Cor 1 ISO 19579 ISO 29541

06.96 Coal - Determination of forms of sulfur 12.92 Solid mineral fuels - Determination of total sulfur - Eschka method 07.96 Solid mineral fuels - Determination of total sulfur - High temperature combustion method - Technical corrigendum 1 02.96 Solid mineral fuels - Determination of total sulfur - High temperature combustion method 05.97 Solid mineral fuels - Determination of chlorine using Eschka mixture 02.96 Solid mineral fuels - Determination of carbon and hydrogen - High temperature combustion method 07.96 Solid mineral fuels - Determination of carbon and hydrogen - High temperature combustion method; Technical corrigendum 1 02.96 Solid mineral fuels - Determination of carbon and hydrogen - Liebig method 07.96 Solid mineral fuels - Determination of carbon and hydrogen - Liebig method; Technical Corrigendum 1 05.97 Solid mineral fuels - Determination of carbon dioxide content - Gravimetric method 12.76 Hard coal - Determination of oxygen content 05.05 Coal - Ultimate Analysis 07.06 Coal - Ultimate Analysis; Technical Corrigendum 1 10.06 Solid mineral fuels - Determination of sulfur by IR spectrometry 10.10 Solid minerals fuels - Determination of total carbon, hydrogen and nitrogen content - Instrumental method

ISO/TC 27/SC 5/WG 7 Brown coal and lignites

ISO 647 ISO 975 ISO 1017 ISO 2950 ISO 5068-1 ISO 5068-2

11.74 Brown coals and lignites - Determination of the yields of tar, water, gas and coke residue by low temperature distillation 10.00 Brown coals and lignites - Determination of yield of benzene-soluble extract Semi-automatic method 12.06 Brown coals and lignites - Determination of acetone-soluble material ("resinous substance") in benzene-soluble extract 02.74 Brown coals and lignites - Classification by types on the basis of total moisture content and tar yield 01.07 Brown coals and lignites - Determination of moisture content - Part 1: Indirect gravimetric method for total moisture 01.07 Brown coals and lignites - Determination of moisture content - Part 2: Indirect gravimetric method for moisture in the analysis sample


Page 42 of 45

Register of Mining Standards 2010-12 ISO 5071-1 ISO 5072 ISO 5073


08.97 Brown coals and lignites - Determination of the volatile matter in the analysis sample - Part 1: Two- furnace method 07.97 Brown coals and lignites - Determination of true relative density and apparent relative density 12.99 Brown coals and lignites - Determination of humic acids

ISO/TC 27/SC 5/WG 8 Major, m inor and tr ace elements in coal and coal r esidues

ISO 601 ISO 602 ISO 622 ISO 1952 ISO 11723 ISO 11724 ISO 15237 ISO 15238

12.81 Solid mineral fuels - Determination of arsenic content using the standard silver diethyldithiocarbamate photometric method of ISO 2590 02.83 Coal - Determination of mineral matter 08.81 Solid mineral fuels - Determination of phosphorus content - Reduced molybdophosphate photometric method 08.08 Solid mineral fuels - Determination of extractable metals in dilute hydrochloric acid 11.04 Solid mineral fuels - Determination of arsenic and selenium - Eschka's mixture and hydride generation method 11.04 Solid mineral fuels - Determination of total fluorine in coal, coke and fly ash 12.03 Solid minerals fuels - Determination of total mercury content of coal 12.03 Solid mineral fuels - Determination of total cadmium content of coal

ISO/TC 27/SC 5/WG 9 Guidelines f or t he validati on o f m ethods

ISO 11726

08.04 Solid minerals fuels - Guidelines for the validation of alternative methods of analysis

ISO/TC 27/SC 5/WG 10 Plastic properties of coal

ISO 349 ISO 501 ISO 8264 ISO 10329 ISO 15585 ISO 23873

01.75 11.03 11.89 02.09

Hard coal - Audibert-Arnu dilatometer test Coal - Determination of the crucible swelling number Hard coal - Determination of the swelling properties using a dilatometer Coal - Determination of plastic properties - Constant-torque Gieseler plastometer method 01.06 Solid mineral fuels - Hard Coal - Determination of caking index 11.10 Hard coal - Method for the measurement of the swelling of hard coal using a dilatometer

ISO/TC 27/SC 5/WG 11 On-line analyzers

ISO 15239

04.05 Solid mineral fuels - Evaluation of the measurement performance of on-line analyzers

ISO/TC 27/SC 5/WG 12 Miscellaneous Methods

ISO 540 ISO 1928 ISO 5074

05.08 Hard coal and coke - Determination of ash fusibility 05.09 Solid mineral fuels - Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value 12.94 Hard coal - Determination of Hardgrove grindability index


Page 43 of 45


FB Mining ISO/TC 82

ISO/TC 82 Mining ISO/TC 82 Mini ng

ISO 721 ISO 722 ISO 723 ISO 1717 ISO 1718 ISO 1721 ISO 1722 ISO 10207 ISO 10208

01.91 Rock drilling equipment - Integral stems 02.91 Rock drilling equipment - Hollwow drill steels in bar form, hexagonal and round 02.91 Rock drilling equipment - Forged collared shanks and corresponding chuck bushings for hollow hexagonal drill steels 06.74 Rock drilling - Rotary drill-rods and rotary drill-bits for dry drilling - Connecting dimensions 01.91 Rock drilling equipment - Drill rods with tapered connection for percussive drillin 08.74 Rock drilling - Extension drill-steel equipment for percussive long-hole drilling Reverse-buttress-threaded equipment 1 1/16 and 1 1/14 (27 and 32 mm) 09.74 Rock drilling - Extension drill-steel equipment for percussive lang-hole drilling Reverse-buttress-threaded equipment 1 1/2 to 2 1/2 in (38 to 64 mm) 02.91 Rock drilling equipment - Rope threaded drill steel equipment for percussive drilling, nominal sizes 22 mm to 38 mm 02.91 Rock drilling equipment - Left-hand rope threads

ISO/TC 82/SC 1 Geologic al and petro graphic symb ols

ISO 710-1 ISO 710-2 ISO 710-3 ISO 710-4 ISO 710-5 ISO 710-6

ISO 710-7

09.74 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 1: General rules of representation 09.74 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 2: Representation of sedimentary rocks 09.74 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 3: Representation of magmatic rocks 04.82 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 4: Representation of metamorphic rocks 07.89 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 5: Representation of minerals 06.84 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 6: Representation of contact rocks and rocks which have undergone metasomatic, pneumatolytic or hydrothermal transformation or transformation by weathering 08.84 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 7: Tectonic symbols

ISO/TC 82/SC 2 Components of coalface machinery using high-tensile round link chains

ISO 610 ISO 1082 ISO 5612 ISO 5613

08.90 08.90 08.90 06.84

High-tensile steel chains (round link) for chain conveyors and coal ploughs Mining - Shackle type connector units for chain conveyors Mining - Scraper bars for chain conveyors Mining - Drive sprocket assemblies for chain conveyors

ISO/TC 82/SC 3 Mining ropes

ISO 3154 ISO 3155 ISO 3156 ISO 5614

06.88 Stranded wire ropes for mine hoisting - Technical delivery requirements 04.76 Stranded wire ropes for mine hoisting - Fibre components - Characteristics and tests 07.76 Stranded wire ropes for mine hoisting - Impregnating compounds, lubricants and service dressings - Characteristics and tests 06.88 Locked coil wire ropes for mine hoisting - Technical delivery requirements


Page 44 of 45

DIN Standard for Mining.pdf

Recommend Documents