This Service Manual describes the technical features and servicing procedures for the Peugeot Satelis 400-500
Descripción: Otkii
Caracteristicas y descripcion tecnica del limpiador industrial para procesos de recubrimientos metalicos
Full description
Resin Damisol® 3340 500 ►
Excellent thermal resistance with good flexibility
►
Highly reactive
►
Suitable for a wide range of generators or motors up to 6.6 kV, including traction motors
►
Usually processed on VPI equipment
►
Class H, UL approved (HC 224°C; TP 185°C) - File E 98 511
General description Base : unsaturated polyesterimide resin. Yellowish, transparent VPI resin with stabilized VinylToluene as reactive diluent (Damidil 9151); hot curing with good permanent temperature properties for electrical insulation systems up to and including Class H. Class 200°C in the samicabond® system for traction. UL Recognition File No. E 98 511 : Twisted Pair 185°C, Helical Coil 224°C. The resin 3340 is available in one or 2 components. Supply form 3340-2 is preferred, when ever there are long transport times as well as high ambient temperatures during transport and storage. Application VPI (Vacuum Pressure Impregnation) of all kinds of windings, but specially on high temperature resistant rotating machines; like traction motors. In combination with the porous Samicapor® tapes, machines up to 6.6 kV can be impregnated. Processing The Damisol 3340 500mPa.s is usually processed on VPI equipment (vacuum pressure installations). Using the 2K Damisol 3340-2, the catalyst mixing ratio is 3% Damicat 9015-N1. Usual Curing process on traction or High Voltage machines combined with Samicapor® : 8 h at 150°C. The resin has to be protected from contamination. A regular viscosity check is therefore necessary. The resin temperature should be 20 - 25°C during impregnation. Packaging 20 kg cans, 200 kg drums, 1000 kg Containers. Storage Conditions 12 months at maximum 15°C in sealed containers protected from light and sun. Higher temperature can be reached during short period of time. If storing the resin in a supply tank we recommend keeping the resin under atmospheric pressure, in dry air or nitrogen. It is advantageous not to fill the supply tank completely. The recommended filling level is 70%. Health and safety . Avoid any contact with skin and eyes, . Work in a well ventilated area, far from any flame, . Wear safety gloves and goggles.
Von Roll France SA F-69330 Meyzieu www.vonroll.com
3340 500 DL 3I41Y 25-10-2012
Value
Test norm
Physical properties Density at 23°C
g/cm³
1.06
Flash point
°C
≥52
Gel time at 120° C
mn
2- 4
Viscosity (Brookfield) at 23°C
mPa.s
500 ± 50
%
0.4
Bond Strength (Helical Coil) MW-35 @ 25ºC
N
215
Bond Strength (Helical Coil) MW-35 @ 155ºC
N
55
Bond Strength (Helical Coil) MW-35 @ 180ºC
N
35
Specific resistivity after 24 h 50 % r.h. at 23°C
Ohms.cm
1 - 5 . 10 Exp 15
DIN 46448/VDE 0360
Specific resistivity after 24 h 50 % r.h. at 155°C
Ohms.cm
1 - 2 . 10 Exp 12
DIN 46448/VDE 0360
Specific resistivity after 240 h storage in water at 23°C
Ohms.cm
1 - 8 . 10 Exp 15
DIN 46448/VDE 0360
Dissipation factor tangente delta (1000 V/50Hz) at 23°C
0.005
DIN 46448/VDE 0360
Dissipation factor tangente delta (1000 V/50Hz) at 155°C
0.03
DIN 46448/VDE 0360
Dissipation factor tangente delta (1000 V/50Hz) at 180°C
0.07
DIN 46448/VDE 0360 DIN 46448/VDE 0360
DIN 46448/VDE 0360
Chemical properties Water absorption after 96 h in water at 23°C
Mechanical properties IEC 1033
Electrical properties
Dielectric strength - initial condition 50 % r.h at 23°C
kV/mm
Dielectric strength - initial condition 50% r.h. at 155°C
kV/mm
120 on max. 20 microns film thickness 80
Dielectric strength after 24 h storage in water at 23°C
kV/mm
≥100
DIN 46448/VDE 0360
Refer to the Material Safety Data Sheet for complet information.
The product properties set forth in this data sheet are based on the results of testing of typical material produced by the affiliated companies of Von Roll Holding Ltd. (underneath referred as Von Roll). Some variation in product properties is typical. Comments or suggestions relating to any subject other than product properties are offered only to call the end-user's or other person's attention to considerations which may be relevant in the independent determination of the use and/or manner of use of product. Von Roll does not claim or warrant that the use of its product will have the results described in this data sheet or that the information provided is complete, accurate or useful. The user should test the product to determine its properties and its suitability for the intended use. Von Roll expressly disclaims any liability for any damage, harm, injury, cost or expense to any person resulting directly or indirectly from that person's reliance on any information contained in this data sheet. Nothing contained in this data sheet constitutes representation or warranty as to any matter whatsoever. Von Roll makes no warranties whatsoever in this data sheet, expressed or implied, including any implied warranty or fitness for a particular use or purpose. Von Roll shall in no event be liable for incidental, exemplary, punitive or consequential damages.
Von Roll France SA F-69330 Meyzieu www.vonroll.com
