http //www.cchongda.com.cn //www.cchongda.com.cn
Contents Note before use…………………………….…………………………….…..2 Operation for Shepherd 260 European Standard Fingerprint Lock ………………………………………………….……....3 1. Notes for functional buttons……………………………………..…..…..3 2. Save fingerprint……………………………………………………..……..3 3. Store password………………………………..…………………………..4 4. Delete fingerprint…………………………………………………………..5 5. Keep unlocking……………………………………………..……………..7 6. Opening the door with fingerprint or password……….………………..7 7. Non –disturbance……………………………………………..…………..8 8. Checking on user’s ID number and the remaining space……………..8 9. Main specification ……………………………………………..………….9 10. Trouble shooting ……………………………………………..………...10
If there has any difference between user’s manual and product, please refer to product.
1 shepherd260
V1.1
http //www.cchongda.com.cn
Note before use 1. Memory capacity 50 persons 2. Authority management 2 levels .The first 5 persons are administrators, 45 persons are users. Only administrators can store and delete users’ fingerprints and have password authority. 3. Alarm for bar proof condition The lock will alarm under the bar proof unlocking condition with continuous beeps. To stop the alarm, please take off the battery. 4. LED Display User’s ID: 01~50
Fingerprint memory space :50~00
Empty user :UU
Full users: FU
5. Low battery prompt While opening the door, 6 beeps indicate the battery is low. Need to replace batteries. The lock still can use about 50 times above.
2 shepherd260
V1.1
http //www.cchongda.com.cn
Operation for Shepherd 260 European Standard Fingerprint Lock 1. Notes for functional buttons Scanning window
LED Display Cycle button
Indicator
Delete button
Slide cover Power on button
Save button Battery Cover
Handle
Handle Inside unit
Password input keyboard
Override key hole
Inside knob
Outside unit
2. Save fingerprint (1) Save administrator’s fingerprint (01~50)
① Press
power
on button.
shepherd260
②Long press SAVE button and hear beep, LED displays 01. Long press again to store the fingerprint. 3
③ Put
fingerprint on the scanning window for 3 times scanning. Once success, hearing 2 prompt beeps, LED displays 02. V1.1
http //www.cchongda.com.cn
After every administrator store fingerprint successfully, the lock will power off .The administrator must verify fingerprint, then go to the next step.
(2) Save users’ fingerprints (06~50)
①
Press power on button, the administrator verify the fingerprint or password successfully.
press Save ②Long button .LED displays the available ID number. Press button to select ID number.
③Long press SAVE button
to store user’s fingerprint (the same as above for administrator ) .
If not power off, you can continuously store users’ fingerprints until memory is full (LED displays FU)
3. Store password (4~12 digits password)
①Press power on
button, the administrator verify the fingerprint successfully.
②Long press save button, LED display password number. Sliding over the cover, again long press save button until hearing prompt beep, indicate to input password.
③After inputting the password, press ENTER button to confirm.
4 shepherd260
V1.1
http //www.cchongda.com.cn
While inputting password, if need to modify password, press CLR button to wait LED displays “ 00 ” , then input again. If the password inputting less than 4 digits ,press ENTER button .If over than 12 digits, it will prompt beep to indicate error operation.
4. Delete fingerprint (1) Delete users’ fingerprints one by one (50~06)
①Press power on button,
the administrator’s or password verify fingerprint successfully.
② Long
press Delete button, LED display ID Number .Press button to select the user to be deleted.
③ Long press DELETE
button. Hearing prompt beep, i.e. deletion is successful.
(2) Delete all of the saved fingerprints quickly(01~50)
① Press power on button,
② Press STORE and DELETE
the administrator’s fingerprint or password verify successfully.
button at the same time. Hearing prompt beep, LED displays “UU ” , i.e. deletion is successful. 5
shepherd260
V1.1
http //www.cchongda.com.cn
(3) Replace administrator’s fingerprint You can only replace the administration’s fingerprint or password, but can’t delete it, while there have fingerprint or password in the lock.
①
Press power on button, the administrator verify the fingerprint .
②
Press DELETE button, hearing prompt beep to indicate storing replacer’ s fingerprint.
(4) Forcedly delete administrator’ s
③
After replaced fingerprint , hearing prompt beep, i.e. replacing is successful.
fingerprint
The administrator’s fingerprint can be deleted directly without verification, but there should no user’s fingerprint in the memory.
②LED displays “ UU ” , i.e.
①Press DELETE button and
deletion is successful.
hold. Press power on button, hearing prompt beep, then remove DELETE button.
6 shepherd260
V1.1
http //www.cchongda.com.cn
5. Keep unlocking Set up
The user verifies the fingerprint or password successfully to unlock the door. Press power on button, blue light twinkle to show unlocking. Release
Press power on button again, green light twinkle 2 times, the function will be automatically released. The door is locked.
6. Open the door with fingerprint or password Open the door with saved fingerprint
① Press power
on button.
Open the door with saved password
the ② Putting saved fingerprint on the scanning window to verify, 2 prompt beep indicate the door is open.
① Sliding over the
cover to power on, hearing a prompt beep, then input password.
②After finish it, press ENTER button, hearing a prompt beep, then open the lock.
7 shepherd260
V1.1
http //www.cchongda.com.cn
7. Non –disturbance Set up
Release
Turning the indoor knob to “RED” position.
Turning the indoor handle to “Green” position.
8. Checking on user’s ID number and the remaining space Check on user’s ID number
Check on the remaining space
Press button to check the remaining space.
Unlocking the door, press button to check the user’s ID number.
8 shepherd260
V1.1
http //www.cchongda.com.cn
9. Main specifications
Specifications 1.
Size
of
fingerprint
scanning
>18mmx22mm
window: 2. Fingerprint sensor:
Optical
3. Fingerprint scanning time:
≤0.2
second
4. Fingerprint recognition time:
≤1.2
second
5. Fingerprint registration times:
3 times
6. False Acceptance Rate (FAR):
0.0001%
7. False Rejection Rate (FRR):
0.1%
8. Fingerprint translation tolerance:
±5mm
9. Fingerprint rotation tolerance:
±180°
10. Fingerprint capacity:
50 persons
11. System power supply:
4 pieces of 5
12. Battery life-span:
support over 8000 cycle operations
13.
Working
environment
AA alkaline cells
－18℃~55℃
temperature: 14. Working environment humidity:
0—99%
The product specifications 15. Dimensions (mm) :
Outside unit:290 x 60 x38 Inside unit: 290 x 64 x 31
16. Weight :
2.5kg
17. Suitable door thickness:
35mm~50mm 9
shepherd260
V1.1
http //www.cchongda.com.cn
10. Troubleshooting Possible Cause
Solution
1. LED do not have any display or display improper
Please check the connecting cable.
2. After installed batteries, press power on button, the system have no any feedback
1. Please check the batteries direction. 2. Please check the connecting cable.
3. After installed batteries, press power on button, the red lamp flash two times and then the system have no any feedback
Please check the lock knob.
4. After install finished, turn the handle, the handle do not come back automatically
It is the installation problem for lockset. There has warp for the holes of handle spindle and the holes of installation. Please follow the cutout template sheet, reconfirm the location of the holes.
5. When power on,6 alert beeps are heard
Low Voltage batteries.
6. After install finished, the system show unlock successfully, but turn the handle, the door do not open.
When install, the handle spindle did not insert the hole of outside unit .Please turn the handle and check if it can drive handle spindle running and then install inside unit .
7. when install, the four screws can not installed in the bottom
In order to fit different door thickness, we prepare two kinds of screws. If the door thickness less than 40mm, please choose the shorter four screws.
8. If the lock knob setup to lock, no way to cancel the handle
The only way to unlock the lock knob is turn inside unit handle.
9. After installed batteries, ribbon is out of battery cover
When install the battery, put the ribbon on the bottom for easy take battery off.
alarm,
Replace
10 shepherd260
V1.1
http //www.cchongda.com.cn 10. After installing outside unit, the lock body can not close to door surface
When install, please do not tighten the screws. While the lock head move freely, then install outside unit.
11. After the door opening successful, close the door again, the system can not power off automatically.
Please check the connecting cable for lockset.
12. After install, close the door, the latch can not hold out
Readjust the depth of strike. The distance between lock and strike should less than 4mm.
13. Using the override key to open the lock, the latch can not hold out
After open lock with override key, it needs to turn normal place and take off.
11 shepherd260
V1.1
