Particular Material Appraisal (PMA) Form.doc

L9:9 MA;U
PARTICULAR MATERIAL APPRAISAL PMA Ref. No.

Rev.

Pressure Pressure Equipment Manufacturer: Address :

Material specification including date:

Grade:

Delivery condition:

Material Group ( Per R !"# $%&':)'''*

"imilar EN material:

Product:

Application + Description of pressure equipment: References of t,e component

Position

-luid type

PED Ris ategory

Dra/ing of t,e component

Applica0le Design ode:

Dimension + t,icness range:

Ma1imum allo/a0le temperature:

Minimum allo/a0le temperature:

Essential "afety Requirements of Materials Materi als for pressure pressure 0earing parts (in finis,ed pressure equipments* equipments* Property

Requirement

Ref. "pecification

Details of ompliance 2 (to 0e verified on material certification*

Appropriate Appropriate properties (Annex I - 4.1(a)) (Assured b !ateria" !anu#a$turer)

Proo# stren%t&'ie"d stren%t& (at appropriate te!perature) UTS ' Creep data

Quote R e; R e/, R m , R m/t/T etc from material specification specificati on or where appropriate properties are obtained

Su##i$ient" Su##i$ient" du$ti"e (Annex I - 4.1(a)) (Annex I - .*)

e.%. #or stee"+ stee" + A !in 14,

Su##i$ient" tou%& (Anne Annex x I - 4.1( 4.1(a) a) Annex I - .*)

e.%. #or stee" /0 !in 2 at 3 C or "o5est operatin% te!perature.

ot significantly affected by ageing !Anne" # $ &' !c((

Appropriate se"e$tion. Suitab"e $o!position

Quote minimum elongation specified in i n material specification, specificati on, A min long % A min trans % Quote impact strength and coincident minimum temperature specified in material specification or additional requirements in the purchase specification or any other alternative measure a( )elect materials that are not liable to !strain( ageing b( confirm that material specification specificati on ensures Al* + ratio  +*' c( confirm plastic deformation not sufficient to cause strain aging&

Su##i$ient" Su##i$ient" $&e!i$a"" resistant to t&e #"uid $ontained $onsiderin% t&e s$&edu"ed "i#eti!e o# t&e e6uip!ent (Annex 1 7 4.1 (b)) se"e$ted in order to a8oid undesirab"e e##e$ts e##e$ts 5&en put to%et&er 5it& ot&er !ateria"s (needs to &a8e e"e$tro$&e!i$a" e"e$tro$&e!i$a"

$o!patibi"it (Annex 1 7 4.1 ($)) Suitab"e #or i ntended pro$essin% (Annex 1 7 4.1 (d)) Materia" Mar=in% Tra$eabi"it (Annex 1 7 >.1.*) Tpe o# !ateria" Certi#i$ate ( Annex 1 7 4.>)

e.%. 5e"din% #or!in% et$

-ethod of traceability to the certification supplied by the material manufacturer& .ertification according to  '0+0*+00 Test Report 1type +&+1

Cat I - Certi#i$ate a##ir!in% $o!p"ian$e 5it& t&e spe$i#i$ation. Cat II III ? I0 - Certi#i$ate o# Spe$i#i$ Produ$t Contro".

.ertification according to  '0+0*+00 #nspection .ertificate 1type 2&' or 1type 2&+1 Materia" Manu#a$turer Appro8a" ( Annex 1 7 4.>) Test pro%ra!!e

@ua"it Sste! o# Materia" !anu#a$turer is $erti#ied IS9 331 b EU Co!petent Bod e.%. re# to E; 1334*-1 E; 1333 E; IS9 >*1- et$ . Spe$i#i$ation &as to be $o!patib"e 5it& PED and resu"ts $o!parab"e 5it& PED ESR.

Do$ ;o.

Resu"ts o# test pro%ra!!e •

Test report

.ontents of this column are provided for guidance to the responses required, other solutions may be equally valid&

Additional Requirements: T&e na!ed !ateria" spe$i#i$ation !a be used #or t&e $onstru$tion o# pressure e6uip!ent intended #or use 5it&in t&e stated "i!its and sube$t to t&e #o""o5in% restri$tions+

Restri$tions+

Si%ned+

Date+ (Pressure E6uip!ent Manu#a$turer)

Con#ir!ed+

Date+ ;oti#ied Bod (Cats III ? I0 on")

Particular Material Appraisal (PMA) Form.doc

Recommend Documents