Mazda Navigation Instruction Rev.2.docx 14-Apr-16 Used MZD firmware version: 56.00.511A (Europe) updated as per instructions on http://mazdacmuhacks.com/?page_id=13 Applied Tweeks using All-in-one_tweaks_V1.43 using All-in-one_tweaks_V1.43 ( http://mazda3revolution.com/forums/2014-2016http://mazda3revolution.com/forums/2014-2016mazda-3-skyactiv-audio-electronics/122458-aio-all-one-tweaks.html ) USB drive formatted to FAT32 SD Card min.8GB Class 10 (I use SANDISK, S DHC Ultra, 16 GB, SDSDUNC-016G-GN6IN, class 10 UHS-I) formatted to FAT32 If it matters, I always unplug USB / SD card through Safe remove option in windows. 1. DOWNLOADS 1.1. Download pack (SD card, CID and lyc files) from https://mega.nz/#F!wFUnxJLL!imw_oFN0kK7bCANQGrhooA 1.2. Download NNGUpdateUSB from NNGUpdateUSB from https://mega.nz/#!Dp1UHAJK!IMgxtP4vWzHf6XJEYr9ey35FoA0BYS94Nf1A4bnY_U0 Or http://s000.tinyupload.com/index.php?file_id=19633859055882141474 1.3. Download JCI_NNG_Tool_v1.30 Download JCI_NNG_Tool_v1.30 from from http://uploaded.net/file/ii94x09t 1.4. Download Mazda Toolbox from from https://mazdaeu.naviextras.com/shop/portal/downloads – DON’T INSERT SD CARD IN CAR 2. PATCHING CID (used files from STEP 1.2 STEP 1.2 and STEP 1.3) STEP 1.3) – DON’T a. Copy all files from StepOneDownloadNNG to your USB drive root folder. b. Plug in the USB drive to the car and wait for the scripts to run. c. When finished, you will see DOWNLOAD COMPLETE. Wait a few seconds and unplug the USB drive and the system will reboot. NOTE: If system doesn’t reboot automatically (mine did) use following steps: To manually restart the Infotainment System, press and hold Mute + Nav + Back on your HMI for 10 seconds. You should see the screen go black then start loading with the Mazda logo. d. The NNG file ( jci-linux_imx6_volans-release jci-linux_imx6_volans-release)) will be downloaded to your USB’s config folder. e. Copy this file over to your computer and save a copy to revert back in the future if needed. f. Patch a copy of the file using JCI_NNG Tool_v1.3 (STEP 1.3) (STEP 1.3) and and the CID (STEP 1.1) (STEP 1.1)
Mazda Navigation Instruction Rev.2.docx 14-Apr-16
g. Rename the patched file to jci-linux_imx6_volans-release h. Once the NNG file is patched, delete the contents in your USB drive (Format to FAT32) and copy over the contents from StepTwoUploadNNG to your USB drive. i. Place the patched jci-linux_imx6_volans-release into the config folder on your USB drive. j. Plug the USB drive into your car to apply the tweaks k. When finished, you will see UPLOAD COMPLETE. Wait a few seconds and unplug the USB drive and the system will reboot. (It may skip this and just reboot). 3. PREPARING SD CARD (used files from STEP 1.1 and STEP 1.4) a. SD card formatted to FAT32 b. Extract all files from sd eu 2016.rar (STEP 1.1) to SD Card root folder c. Replace file jci_mazda_feur_14q2_hm_fpa_fsp_hnr_dem_3dlm_3dc_poi_spc_ph_tts_vr_jv_lb_n mwxgqmn45xy4vfbmc4vdw3p73.lyc (located in SD Card license folder) with file jci_mazda_feur_14q2_hm_fpa_fsp_hnr_dem_3dlm_3dc_poi_spc_ph_tts_vr_jv_lb_n mwxgqmn45xy4vfbmc4vdw3p73.lyc downloaded in STEP 1.1 d. Go to your car and plug in prepared SD Card e. Try to start navigation f. If maps are not shown, unplug SD card from Car and plug it in your PC g. Run Mazda Toolbox (downloaded in STEP 1.4) h. Wait until Mazda Toolbox recognize the card (I have also created new account through Mazda Toolbox) i. Update Navigation if necessary (I didn’t have to because files from STEP 1.1 are already updated) j. Close Mazda Toolbox, unplug SD card k. Plug SD card in your car and try I didn’t create any of the files therefore all the credits go to their respective authors to who I can only say THANKS A LOT for all the effort they put in this and for sharing their findings.
All the files and discussion can be found on Mazda3Revolution forum http://mazda3revolution.com/forums/2014-2016-mazda-3-skyactiv-audio-electronics/128170-eumaps-download-cid.html THANKS one more time.
