Conectores internos
Dual-channel, 2 Slots, Non-ECC, Unbuffered, 240 pin DDR3, Max. up to 16GB for all.
PS/2 KB/MS ports
Types: 1066/PC3-8500, 1333/PC3-10600, 1600/PC3-12800
Graphics
12
ROM Recovery
Realtek ALC662 Gigabit : Realtek RTL8111G
BUZZER Memory sockets
Serial Port/ Display (DVI) port
2 x PCI slots LAN
COM
2x SATA III connectors
Storage
10
Display (VGA)/ HDMI ports
2x SATA II Connectors 8 x USB 2.0 ports, 12/480Mbps
USB
ATX power connector
7
2 x USB 3.0 ports, 5Gbps 1x PS/2 Mouse/Keyboard
LAN (RJ-45) port & USB3.0 ports
4x USB2.0 ports
USB2.0 connector
System FAN 14
1x ATX power connector
10
1x Front panel audio connector 1x Front panel connector 8
1x Internal serial port connectors 1x TPM (Trusted Platform Module) connector
SATA3.0/2.0 connectors
PCI slots
1x Chassis intrusion connector
7
Front panel connector
1x ME Update
BIOS
SPI 64Mb (AMI)
Form factor
uATX, 9.6inches x 7.5 inches
1
2
SPDIF_OUT
Front panel audio connector
Conectores del panel trasero Display (VGA) port
A
LAN (RJ-45) port
B
6
CLEAR CMOS
3 2 1
3 2 1
Normal (Default)
Clear CMOS
Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts
A
INTRUDER Clear CMOS
FLASH OVERRIDE (Intel Management Engine) SELECTOR FLASH_OVERRIDE 1
1
2
2
Enable (Default)
USB3.0
Disable
13
ATX CPU POWER CONNECTOR
ATX_CPU
ROM RECOVERY CONNECTOR
SPI_CS# SPI_MOSI SPI_MISO
SPI_CS +3P3VSB GND
SPI_CLK
ATXPOWER
Ground +12V_CPU
USB2.0
5
11
Ground +12V_CPU
Pink: Mic Input
HDMI ports
4
Serial port TPM header FLASH header OVERRIDE
B
Clear CMOS
Lime: Front L/R Output
Display (DVI-D) port
3
LPT header
Selectores de función
Blue: Line Input
Keyboard (PS/2) Port
F_USB3 F_USB2
SATA1
UEFI
14
12
CPU FAN CONNECTOR
Ground CPU FAN PWR CPU FAN TACH CPU FAN PWM
1x Clear CMOS selector & 1x Clear password selector
SERIAL Port
+SBV USB*(-) USB*(+) Ground NC
SATA2
ATX POWER CONNECTOR +3 Volts +12 Volts +12 Volts +5V Standby ATX_PWRGD Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts
2 x USB 2.0 connectors
Mouse (PS/2) Port
+SBV USB*(-) USB*(+) Ground
PCI Express slot (x1)
4x SATA connectors
Internal Selectors
USB CONNECTORS
SATA3
FRONT PANEL
1x System fan connector Internal connectors
9
SATA3.0/2.0 CONNECTORS
PWRBTN PLED
PCI Express slot (x16)
1x CPU fan connector
INTRUDER
SATA4
PLED(+) PLED( - )
9
Audio jacks
1x ATX CPU power connector
PWR Ground
1x LAN (RJ-45) port + 2x USB2.0 ports 3x Audio jacks (5.1 CH)
8
FRONT PANEL CONNECTOR HDLED(+) HDLED( - ) Ground Reset NC
1x Display (DVI) port 1x HDMI port
TPM
RESET HDLED
USB 2.0 ports
1x Display (VGA) port Rear Panel I/O ports (Depending on Model)
INTRUDER
GND
1 x PCI Express slot (x1)
NC LAD2 LAD1 GND NC SERIRQ GND SMB_CLK_MAIN
1 x PCI Express slot (x16)
Audio
6
11
Integrated Graphics
Expansion slots
TPM (Trusted Platform Module) CONNECTOR
Ground SATA_RX(+) SATA_RX(-) Ground SATA_TX(-) SATA_TX(+) Ground
Memory
CPU fan connector
13
Intel H81
DDCD*# TTXD* Ground RRTS*# RRI*#
Chipset
5
RRXD* DDTR*# DDSR*# CCTS*#
TDP: 95W
INTERNAL SERIAL PORT CONNECTOR
CK_33M_TPM LFRAME# PLTRST# LAD3 +3P3V LAD0 LDREQ0# +3P3VSB GND LPCPD#
ATX CPU power connector
Intel socket 1150
CPU Socket
4
PARAELLE
Ground INTRUDER#
Diseño de Motherboard
INTERNAL PARAELLE PORT CONNECTOR
NC Ground Ground Ground Ground Ground Ground Ground Ground SLIN# PINIT# ERROR# AFD#
SPDIF_OUT
F_AUDIO
Especificaciones
3
SPDIF_OUT CONNECTOR
MIC*_L MIC*_R LINE*_R GND LINE*_L
• Especificaciones • Selectores de función • Diseño de Motherboard • Conectores internos • Conectores del panel trasero
2
SLCT PE BUSY ACK# SPD7 SPD6 SPD5 SPD4 SPD3 SPD2 SPD2 SPD1 SPD0 STB#
GND F_AUDIO_DET# MIC*_RTU
Contenidos
FRONT PANEL AUDIO CONNECTOR
+5V
1
Ground SPDIF Out
Referencia de diseño de Motherboard
LINE*_RTU
CX
H81-M1 Series
CPU_FAN
SYSTEM FAN CONNECTOR
Ground SYS FAN PWR SYS FAN TACH SYS FAN PWM
SYS_FAN
Indicadores LED del puerto LAN Left (ACTIVITY) Green: Activity Off: No activity
LAN port
Right (LINK) Orange: 1G Link Green: 100M Link Off: 10M Link
Para borrar los ajustes de usuario CMOS RTC RAM: 1. Apague el ordenador y desconecte el cable de alimentación. 2. Mueva el jumper para borrar el BIOS por 5 a 10 segundos, luego mueva jumper por defecto. 3. Conecte el cable de alimentación y encienda el equipo. 4. Durante el proceso de arranque, entrar en la configuración del BIOS para volver a entrar en la configuración del usuario.
Soporte técnico: 0810 - 7777 - 247
www.redcx.com
[email protected] Las imágenes son sólo ilustrativas.
