IMPULSE METAL DETECTOR KOSCHEY-5I Instruction manual
Kosch!MD"com
#" Intro$uction
KOSCHEY 5i - is a modern microprocessor-based universal pulse metal detector. The device is intended for search of the metal objects in the round! sand! "alls! thic# rass! etc. usin the device bundled "ith interchaneable sensors of different si$e allo"s to solve a "ide rane of search tas#s in the treasure! construction! in search of lost thins and in other specific areas of human activit%. %" Main tchnical charactristics
The ma&imum depth of detection of objects 'b% air() *rinted sensor '+5 cm diameter( - Coin diameter of +5mm - up to , cm - Helmet '// 00( - to 1cm - 2a&imum depth 3 up to 45 cm /ith deep loop-sensor '4!+&4!+m( Helmet - 4 cm Steel barrel +6 - up to +cm The ma&imum depth is up to ,cm. 0ndication) - 7isual led - 8udio multi-tone The search mode is static Time of continuous operation at the batter% is full% chared - in econom% mode up to 45 hours - in normal mode! up to 9 hours. - in turbo mode up to 5 hours :ar lenth adjustable '9-4 mm ( 2ass! not more than) - printed sensor + # - "ith a loop sensor + # &" O'ration con$itions
,.4. 8ir temperature -4...;5<=. ,.+. 8tmospheric pressure >4...9 mm of mercur% ,.,. 8la humidit% air up to ?5@ at temperature ;+5<=. ,.. Cat(oricall! $o not o'rat an! a''lianc )ith th co*r rmo*$ or $ama($ insulation snsor ca+l +caus o, th ris o, lctric shoc .
." Dli*r! st
.4. The electronic control bo&. .+. The sensor. .,. Telescopic bar. .. 8cid sealed batter% 4+ 7! 4., 8h .5. 2ains charer. Aote) Beep loop-sensor in a base complete set is not included and must be purchased separatel%.
+
5" Th 'rinci'l o, action
The principle of action of a pulse metal detector Kosche%-50 based on e&citation in the metal object pulsed edd% currents and the secondar% dimension electromanetic fields that induce these currents. sin the built-in microprocessor device anal%$es this reradiated sinal and produces a correspondin indication of the object detected. /" Pr'aration ,or o'ration
:efore usin the device must be brouht into "or#in position) Aot telescopic bar to the desired lenth and loc# it "ith a collet clamp. 1.+. Secure the sensor to the bar throuh the plastic bolt. /hen usin loop-depth sensor to act in accordance "ith the instructions on this sensor. Chan( o, snsors to 'ro$uc onl! )hn 'o)r is o,,0 1.,. 8ttached to the barbell electronic unit. The cable connectin the electronic unit and the sensor ent"ine -5 times around the bar. Connect the connector of the sensor to the electronic module and carefull% tihten the nion nut connector 'b% hand(. 1.. 8ttached to the arm the armrest and storae compartment "ith curl% nuts. 1.5. The suppl% cable ent"ine +-, times around the bar and to connect po"er suppl% connector to the electronic unit. 1.1. 0f necessar%! connect the headphones into the jac# located on the rear panel of the device. 1" D*ic o'ration
To enable the device! %ou must remove the sensor ,-cm from an% metal object and the round and turn on the s"itch on to upper position 234! "hich is located on the front panel of the device. 0mmediatel% after turnin on the unit performs a self-test. 8t this time! the device pla%s the melod%! the beat "hich turns includes 6EBs. Note: the sound is played through the internal speaker or with headphones. The further manaement of the detector is done usin the volume threshold level 'volume( buttons balance 64678 and the mode s"itch indicator 9:;<=. On Di. depicted the front of the detector. 0f %ou turn on the device press and hold the balance 64678 button! then usin the volume threshold slider! %ou can adjust the volume. The melod% "ill be pla%ed as lon as the button is held do"n. 8fter releasin the button! the device "ill save the adjusted volume level in non-volatile device memor%.
Pict" #" >ront 'anl
The mode s"itch 9:;<= allo"s %ou to choose one of three modes) 4 - EconomicalF! + - AormalF! , - Turbo modeF.
,
Pict" %" ?ac 'anl @" Practical rcommn$ations
Gettin started %ou need turn on the device and "ait "hile the self-test. 8fter successful passin of tests "ill liht the $eroF 'reen( led. Ae&t! s"itch the 2ode %ou "ant to select the operatin mode. 0t should be noted that the transition from eular to Eco mode reduces the depth of detection of various tarets b% about 4-+@! and the transition from the Aormal to the Turbo mode about the same increases the depth. Ho"ever! electricit% consumption in different modes chanes in proportions 'see chapter +(. So %ou need to balance selected mode "ith the scheduled time. Gettin started the surfin is necessar% to drop the sensor to the round at a distance of ,-5cm to print sensor and 4-+cm for the deep loop sensor. 8fter this press the balance #nob 64678. Dor some time 'usuall% a fraction of a second! in a ne" place not more units of seconds(! the device "ill produce the adjustment accompanied "ith short sound. Burin the adjustment the device indicates the current mode b% flashin 6EBs. The principle indicatin the follo"in) the first three 6EBs indicate the t%pe of the connected sensor) -th led is printed sensor! 4- a deep loop sensor! + - additional sensor. The other 6EBs sho" the search mode) ,rd diode meet the Economic mode! th - sual! 5th - Turbo mode. Dor e&le! if durin the adjustment blin# 4-th and -th 6EBs! it means that the device connected to the deep loop sensor! the device operates normall%. 8fter balancin the unit "ill emit a special sound sinal and "ill be read% to search. 0n this mode! the 6EBs indicate the level of sinal reradiated b% metal taret. The bier the taret and closer to the sensor! the stroner the sinal and the reater number "ill have the liht of the led. 8lso toether "ith sinal level "ill chane the pitch and the volume of the audio sinal. Ao" %ou must set the necessar% sensitivit%. This must be done "ith the thumb"heel sensitivit% threshold. You need to rotate the #nob until there is no false positives. Ao" "e can proceed to search. The detector "or#s in the static mode. So the sensor can be moved above the round "ith an% comfortable speed. pon detection of a metal object "or#s of visual and sound indication. Slo"l% movin the sensor over the taret usin visual and sound indication can determine the location on the round "here the sinal is larer. /ith hih probabilit% it can be arued that the center of the taret is riht in this place. The e&ception is the taret of the comple& form. 8lso has its o"n characteristics reaction loop depth sensor close to the taret of a small si$e. Such objects device feelsF just riht ne&t to the turns of the loop. Burin the search! if necessar%! repeat the balance 'reset( of the device! press the balance #nob 64678.
/hen the batter% is belo" the permissible level "ill trier an audible and visual alarm. 0n this case the operations "ith metal detector %ou need to stop! to s"itch off the device and rechare or replace the batter%. To chare the batter%! %ou must disconnect the po"er connector from the electronic bloc# and insert it into the slot of the charer. The charer must be connected to the net"or#. 8t the end of the chare on the front panel charer led "ill liht up. To e&tend batter% life! it should be stored in a chared state. pon completion! the device should be addressed in the reverse order of the 8ssembl% 'chapter 1(. *ets transport and storae metal and assembled. 0n this case it is recommended to disconnect the po"er connector from the electronic bloc# to prevent the inadvertent po"erin the unit and the batter%.
" T!'ical mal,unctions an$ mtho$s o, thir limination
Charactristic ,aturs o, th mal,unctions
4. 8fter turnin the detector on! no visual and sound indication.
+. Dlashin the 4st led is on! the unit loses an&ious tone.
Pro+a+l caus
Trou+lshootin( mtho$s
The suppl% voltae is not To replace the fuse on the supplied to the electronic batter% compartment unit. eplace the po"er cable Dault% or deepl% To replace the batter%. dischared batter% Short circuit in the circuit To contact customer of the sensor. service. eplace the sensor.
,. Dlashin the +st led is on! the unit loses an&ious tone.
The batter% is dischared.
echare or replace the batter%.
. Dlashin the ,st led is on! the unit loses an&ious tone.
Burin the self-test detected a fault.
To contact customer service.
5
