MANUAL DE PARTES RETRO CASE 580SL SERIES 2 .pdf

1-1

580 Super L Series 2 Loader Backhoe Parts Catalog Bur 7-3350

BP97N058

This unit first became available February, 1998.

Bur 7-3350

Copyright © 1998 C a s e Corporation C A S E and IH are registered trademarks of C a s e Corporation

Issued February, 1998

1-2

580 Super L Series 2 Loader Backhoe

LOCATION OF SERIAL AND PRODUCT IDENTIFICATION NUMBERS Please use the horizontal lines provided to record these important serial numbers, product identification number, and part number.

PRODUCT IDENTIFICATION NUMBER (Above loader lift arm pivot point)

ROPS CANOPY SERIAL NUMBER (Right-hand side of canopy)

CAB SERIAL NUMBER (Left-hand side of front console) ENGINE SERIAL NUMBER

LOADER BUCKET PART NUMBER

BACKHOE BUCKET PART NUMBER

TRANSMISSION SERIAL NUMBER

FRONT DRIVE AXLE SERIAL NUMBER


1-3

PICTORIAL SECTION INDEX GENERAL

ENGINE

2

FUEL

3

ELECTRICAL

4

STEERING

5

POWER TRAIN

6

BRAKES

7

HYDRAULICS

8

CHASSIS AND MOUNTED EQUIPMENT

9

NUMERICAL INDEX Bur 7-3350

1

10


1-4


GENERAL INFORMATION Indexes

Right-Hand and Left-Hand Identification

Section 1 of this catalog contains a SN and P.I.N, location guide, alphabetical index, pictorial index of the sections included, and pictorial index(es) for quick location of hoses and tubes (and other system components in some catalogs). An alphabetical Index also appears at the beginning of each section. Section 10 is the Numerical Index which lists all part numbers in alpha/numeric order with their page location and reference number.

The reference to right-hand and left-hand in this catalog is identified by the operator standing at the rear of the basic unit (without rear attachment), looking toward the front of the machine (in normal forward travel). For pages covering any machine attachments, right-hand and left-hand are defined by the operator sitting in the position for proper operation of the attachment.

Catalog Revisions and Supplements

Illustrations The arrangement of this parts catalog is for easy identification of parts. All parts are illustrated in "exploded views" In proper relation to each other. Reference numbers used in the illustrations refer to those on the text pages. The text pages list reference number, part number, part description and the quantity required.

Changes to the product may make it necessary to revise or add pages to this catalog. A cover sheet will list all pages released in a revision or supplement. Each new or revised page will have a new issue date. All revised and new pages must be put into the parts catalog as soon as they are received.

Parts Orders Orders must specify product model, all necessary serial numbers, correct part number, complete description, quantity required, method of shipment, and shipping address.

Abbreviations P.I.N. "Product Identification Number" SN "Serial Number" NSS "Not Serviced Separately" in the part number column indicates this part is not available for service. REF "Reference" in the part number column indicates this part has special service information. The page where this information can be found is given in the part description column. UAR "Use As Required" in the quantity required column indi-

Text Format Explanation An assembly may contain service Items. The component parts of an assembly or subassembly are indented. The quantity required column lists the number of assemblies required for a completed machine, and the number of components required in a complete assembly or subassembly.

cates the number of parts used is determined by service needs.

The example below Illustrates the use of indents and other text page elements explained on this page.

HYDRAULIC FILTER REF. 1 2 3 4 5 6 7 8 9 10

PART NO. D4356734 D61903 NSS D58199 D43800 NSS A27994 D61948 REF 843065C1 113-323 814-8030

DESCRIPTION FILTER ASSEMBLY - hydraulic oil, P.I.N. 7534840 and after HEAD ASSEMBLY - filter HEAD - filter, order D61903 head assennbly VALVE - bypass KIT - filter element, replaces D35700 elennent kit ELEMENT - filter, order D43800 element kit O-RING - filter HOUSING -filter CANOPY - ROPS, order form Machinery Price List HOSE - 3353 m m (132 inch) long, reservoir to pump BOLT - hex, 7/16 NC x 1 -3/4 inch BOLT - hex, 8 - 1.25 x 30 mm

REO'D.

2 4


1-5

ALPHABETICAL INDEX B

Accumulator, Ride Control...: 8-123 Air Cleaner j 2-9 Air Cleaner Mounting j 2-7 Air Conditioner Blower j 9-137 Compressor and Mounting! 9-145 Condenser ' 9-143 Controls 9-125 Drain Lines j 9-137 Evaporator Core 1 9-141 Filter-air '. 9-135 Receiver-Drier [. 9-143 Ventilation Ducts 9-137 Air Filter - cab 9-135 Alarm - backup 1 4-41 Alarm - warning, engine oil pi;essure 4-19 Alarm - warning, engine water temp 4-19 Alarm - warning, parking brake 4-19 Alternator - electrical 1 4-7 Alternator Mounting i 4-9 Antenna - radio j 4-45 Antirollback - loader 9-11 Auxiliary Hydraulics ' Backhoe 4-47,8-51 - 8-55,9-43 Hand Held 4-21,8-41 - 8 - 4 9 Axle - Front - four wheel drive Differential .| 6-15 Drive Shaft J 6-19 Housing .; 6-5 Mounting ' 6-3 Planetary 6-13 Ring and Pinion 1 6-17 Shafts 1 6-11 Steering Cylinder 6-9 Swivel Housing ' 6-7 Axle - Front - two wheel drive] 5-15 Axle - Rear Drive Differential 6-61 Differential Brake 1 7-3 Differential Lock 6-57,6-65 Drive Shaft [ 6-69 Housing 6-59 Mounting 6-55 Parking Brake 1 7-5 Planetary 6-67 Ring and Pinion Gear Set 6-63 B

Backhoe Boom Boom Latch Boom Lock

Bur 7-3350

;

! !

9-49 9-53 8-57,8-59

Backhoe-Cont. Buckets 9-63-9-71 Controls (See Controls) Control Tower and Covers 9-25,9-27 Coupler - bucket 9-55 - 9-59 Dipper 9-55 Extendable Dipper 9-59 Frost Point Assembly 9-73 Hydraulics (See Hydraulic Systems) Stabilizers 9-45 Swing Tower 9-47 Valves (See Valves) Backhoe Auxiliary Hydraulics 8-51 - 8-55 Backup Alarm 4-41 Baffle Plates - front covers 9-85 - 9 - 8 9 Battery - with cold start 4-15 Battery - without cold start 4-13 Battery Box 9-79 Beacon - rotating 4-43 Bearings -, front wheel 5-17 Belts - fan, alternator, and compressor 2-3,4-9,9-145 Belts-seat 9-103 Block - cylinder 2-39 Blower - air conditioner 9-137 Boom Latch 9-53 Boom Lock 8-57,8-59 Boots A;ccelerator Pedal 3-9 Backhoe Levers 9-25 Boom Latch Lever 9-53 Brake Master Cylinder ; 7-11 Lamp Socket, instrument cluster 4-27 Loader Lever..... 4-21,9-3,9-5,9-7 Transmission Gear Shift Lever 6-23 Transmission Shifter Mechanism 6-35 Transmission Shuttle Shift Lever - FNR... 4-17 Box - battery 9-79 Box-tool.. 9-81 Brake - differential, rear axle 7-3 Brake - pai-king, lever 7-13 Brake - parking, rear axle 7-5 Brake Alarm - parking 4-19 Brake Master Cylinder Assembly 7-11 Hydraulic Circuit 7-9 Mounting 7-7 Brake Pedals 7-7 Buckets - backhoe 9-63 - 9-71 Buckets - loader 9-15-9-19


580 Super L Series 2 Loader Backlioe

1-6

ALPHABETICAL INDEX c Cab Air Conditioner 9-135 - 9-145 Air Filter 9-135 Blower Housing 9-137 Condenser - air conditioning 9-143 Covers - interior 9-115 Doors and Windows 9-117 - 9-123 Drain Lines - air conditioning 9-137 Electrical and Lighting 4-31,9-125 Evaporator Core 9-141 Frame 9-115 Glass 9-113 Headliner, Louvers, and Dome Lamp 9-133 Heater 9-137,9-139 Insulation 9-115 Panel - cab control 9-125 Receiver-Drier - A/C 9-143 Ventilation Ducts 9-137 Windshield Washers 9-127 Windshield Wipers 9-129,9-131 Cables - battery 4-13,4-15 Camshaft - engine 2-37 Canopy - ROPS 9-147 Chaff Screen 9-93 Chassis - tractor 9-77 Cluster - instrument 4-27 Clutch Cutout 4-11,4-21 Coat Hook 9-115,9-147 Cold Start - dual battery 4-15 Cold Start System - ether 2-13 Column - steering 5-9 Compressor and Mounting - A/C 9-145 Controls Antirollback - loader 9-11 Backhoe Excavator Control Pattern 9-39 Foot Swing 9-29 - 9-33 Hand Swing 9-35 ,9-37,9-41 Backhoe Auxiliary 9-43 Boom Latch 9-53 Boom Lock 8-57,8-59 Brake 7-7,7-13 Clutch Cutout 4-11,4-21 Differential Lock - rear axle 6-57,6-65 Extendable Dipper 9-33,9-41 Hand Held Auxiliary 8-49 Loader Bucket 9-3 Clam 9-5,9-7 Lift 9-3 Self-Leveling 9-9

Bur 7-3350

C Controls-Cont. Parking Brake 7-13 Return-to-Dig - loader 9-11 Ride Control 8-61,8-63 Self-Leveling - loader 9-9 Steering 5-3 Throttle 3-7,3-9 Transmission Gear Shift 6-23 Transmission Shifter Mechanism 6-35 Transmission Shuttle Shift (F/N/R) 4-17 Control Tower and Covers - backhoe.. 9-25,9-27 Cooler - hydraulic oil 6-21,8-9 Cooling Systems Engine 2-3 Engine Oil 2-29 Hydraulic Oil 8-9 Transmission 6-21 Core - evaporator, air conditioner 9-141 Countenweight - front 9-75 Coupler - backhoe bucket 9-55 - 9-61 Coupler - quick, loader hydraulic tool 9-23 Couplings - auxiliary hydraulics, hand held 8-45,8-47 Couplings - hydraulic line disconnect 8-3 Couplings - hydraulic pump to engine 8-3 Covers Anti-Vandalism Instrument Panel - front 4-23 Instrument Panel - side 4-25 Auxiliary Hydraulic Control 9-25 Backhoe Control Tower 9-25 Baffle Plates - front 9-87,9-89 Battery Box 9-79 Cab Interior 9-115 Chassis Upright 9-93 Cylinder Head 2-33 Fender - plastic/velcro 9-97,9-99 Front Gear 2-19 Instrument Panel 4-23,4-25 Loader Control 4-25 Loader Lift Frame Tubing 3-3,9-79 Pump Guard - front 9-85 Rear Closure Panel - canopy 9-97 ROPS Canopy Post 9-147 Steering Column 4-23 Crankshaft 2-43 Cylinder - brake master 7-11 Cylinder Block 2-39 Cylinder Head 2-33


580 Super L Series 2 Loader BacMnoe

1-7

ALPHABETICAL INDEX C Cylinders - hydraulic Boom - backhoe Bucket - backhoe Bucket - loader Clam-loader Dipper - backhoe Dipper Extension - backhoe Lift - loader Stabilizer - backhoe Steering-2WD Steering-4WD Swing - backhoe

8-137 8-141 8-129 8-131 8-139 8-143 8-127 8-133 5-13 6-9 8-135

D

Decals 9-153-9-157 Differential and Differential Lock rear axle 6-57,6-61,6-65 Differential - front axle 6-15 Dipper 9-55,9-57 Dipper - extendable 9-59,9-61 Dipsticks Oil Level - engine 2-41 Transmission 6-23 Dome Lamp 9-133 Drive Shaft Front Drive Axle to Transmission 6-19 Rear Drive Axle to Transmission 6-69 Drive Shaft Guards 6-3 E Electrical Circuits and Components Alternator Backhoe Auxiliary Hydraulics Backup Alarm Battery Blower-cab Boom Lock Cold Start System Compressor - air conditioner Control P a n e l - c a b Coupler - quick, loader hydraulic tool Hand Held Auxiliary Hydraulics Harness - engine Harness - front console Harness - lamp, cab Harness - lamp, canopy Harness - side console Horn Instrument Cluster Lamp-cab Lamp - ROPS canopy

Bur 7-3350

4-7 4-47 4-41 4-13,4-15 9-137 8-57,8-59 2-13,4-15 9-145 9-125 8-65,8-67 4-21 4-11 4-17 4-31 4-29 4-19,4-21 4-41 4-27 4-35,4-39 4-33,4-37

E Electrical Circuits and Components-Cont. Outlet - power plug 4-21 Radio Ready Package 4-45 Return-to-Dig 9-11 Ride Control 8-61,8-63 Rotating Beacon 4-43 Starter 4-3,4-5 Washer - windshield 9-127 Wipers 9-129,9-131 Engine and Fuel Injection Components Aneroid 3-15 Camshaft 2-37 Crankshaft 2-43 Cylinder Block/Block Heater 2-39,2-41 Cylinder Head and Cover/Thermostat 2-33 Flywheel and Housing 2-45 Fuel Filter 3-11 Fuel Injection Nozzle 3-19 Fuel Injection Pump and Drive 3-17 Fuel Injection System 3-13 Gasket Kits 2-49,2-51 Gear Cover 2-19 Heater - engine oil 2-41 Manifolds 2-21 Oil Filter and Cooler 2-29 Oil Pump and Pan 2-31 Pistons/Connecting Rods 2-47 Pump - transfer, fuel 3-11 Turbocharger Assembly 2-25 Turbocharger System 2-23 Valve Mechanism 2-35 Wastegate Actuator 2-27 Wastegate System 3-15 Water Pump Systems 2-17 Engine Mounting 2-15 Equipment Pump Assembly 8-71 Mounting 8-3 Evaporator - core, air conditioner 9-141 Exhaust/Intake Manifolds 2-21 Exhaust System and Muffler 2-11 F Fans Alternator Engine Cooling Fenders-cab Fenders - ROPS canopy, rear Filters Air - engine Cab Air Engine Oil

4-7 2-3 9-99 9-97 2-9 9-135 2-29



1-8

ALPHABETICAL INDEX F Fiiters-Cont. Fuel 3-11 Fuel - In-line 3-3 Hydraulic Oil 8-125 Precleaner 2-9 Transmission Oil 6-27 Floor Plates and Mats 9-95 Flywheel and Housing 2-45 Frame Backhoe (See Backhoe) Cab 9-115 Canopy 9-147 Coupler - quick tool 9-23 Doors-cab 9-117-9-121 Loader 9-11 Tractor (chassis) 9-77 Frost Point Assembly 9-73 Fuel Filter 3-11 Fuel Injection Nozzle 3-19 Fuel Injection Pump 3-17 Fuel Injection System 3-13 Fuel Level Sensor 3-3 Fuel Reservoir Lines 3-3 Fuses Auxiliary Hydraulics, Backhoe 4-47 Auxiliary Hydraulics, Hand Held 4-21,8-43 Boom Lock 8-57 Coupler - quick, loader hydraulic tool 8-67 Instruments and Equipment 4-19 Ride Control 8-61 Seat - deluxe air suspension 9-105

G Gaskets - engine 2-49,2-51 Gauges Cylinder Head Bolt Length - engine gaskets 2-49 Instrument Panel Cluster 4-27 Oil Level - sight 9-79 Grille - chaff screen 9-93 Grille Unit 9-93 Guards Baffle Plates 9-87,9-89 Drive Shaft 6-3 Loader Crossover Tube 8-15 Loader Self-Leveling Cable 9-9 Mud 9-101 Pump 9-85 Valve - loader control 9-21 H

Hand Held Auxiliary Hydraulics

Bur 7-3350

H

Harness - electrical Adapter - cab 4-19 Adapter - engine 4-19 Auxiliary Hydraulics - Backhoe 4-47 Auxiliary Hydraulics - Hand Held 4-21 Backup Alarm 4-41 Blower Jumper 9-137 Boom Lock 8-57 Cab 4-31,9-125 Canopy 4-29 Chassis Options 4-19,4-47,8-63,8-67 Coupler - quick, loader hydraulic tool 8-67 Engine 4-11 Front Console 4-17 Horn 4-41 Optional Equipment 4-19 Radio 4-45 Ride Control 8-63 Seat 9-105 Side Console 4-19,4-21 Side Console Options 4-19,4-47,8-63,8-67 Transmission Lever clutch cutout 4-11 Head - cylinder and cover 2-33 Headliner - cab 9-133 Heater-cab 9-137,9-139 Heater - engine block 2-41 Heater - engine oil 2-31 Hood and Latch Release 9-93 Hook, Coat 9-115,9-147 Horn - electric 4-41 Hub - front wheel 5-17 Hydraulic Systems Auxiliary Backhoe 8-51 - 8 - 5 5 Hand Held 8-41 - 8 - 4 9 Backhoe Boom 8-25 Backhoe Bucket 8-29 - 8-35 Backhoe Dipper 8-27 Backhoe Dipper Extension 8-37 Backhoe Stabilizer 8-21 Backhoe Swing 8-23 Boom Lock 8-57,8-59 Brake Master Cylinder 7-9 Coupler - quick, loader hydraulic tool 8-65 - 8-69 Differential Lock, rear axle 6-57 Equipment Primary Oil Cooler Lines and Filter 8-9 Pump and Loader Valve to Backhoe Valve 8-7

8-41 - 8-49


580 Super L Series 2 Loader Backiioe

1-9

ALPHABETICAL INDEX L

H

Hydraulic Systems-Cont. Equipment Primary-Cont. Reservoir to Loader Valve and Loader Valve to Filter Return Lines Loader Bucket Loader Clam Loader Lift Loader Valve to Backhoe V a l v e without auxiliary hydraulics, with or without extendahoe Ride Control...., Steeririg

Index - numerical Injection Nozzle - fuel Injection Pump - fuel Injection Systerri - fuel Injector Nozzle - ether Instrument Cluster ..^ Instrument Panels and Covers Intake/Exhaust Manifolds

.....8-3,8-5 8-9 8-13,8-15 8-17,8-19 8-11

8-39 ...8-61,8-63 5:5,5-7

10-2 3-19 3-17 3-13 2-13 4-27 4-23,4-25 2-21

Kits Axle, Kingpiri - two-wheel drive front. 5-15 Backhoe Control - excavator control pattern 9-39 Boom Lock 8-57,8-59 Boom Lock Solenoid Valve 8-121 Brake Discs - rear axle 7-3 Brake Master Cylinder 7-11 Brake Self-Adjuster - Rear Drive Axle 7-3 Cylinders (See Cylinder - Hydraulic) Equipment Pump ......8-71 Filter, Oil - hydraulic .8-125 Harness - non-air conditioned to air conditioned 4-19 Mirror - rear view 9-149 Radio Ready Package . 4-25,4-45,9-133 Seat (See Seat - Operators) Steering Control Valve - low torque 5-11 Steering Cylinder - front drive axle... 6-9 Steering Cylinder - two wheel drive axle...5-13 Transmission Oil Pump Piston Valve 6-33 Synchronizer 6-35,6-37,6-41 - 6-45 Universal Joint - drive shaft 6-19,6-69 Valve. (See Valves) Wheel Bearing, front axle .....5-17

Bur 7-3350

Lamp - dome, cab j— 9-133 Lamps - tractor 4-33 - 4-39 Latch Release - hood.....; ;. 9-93 Levers - control (See Controls) Loader Antirollback 9-11 Bucket and Cylinder Links 9-13 Buckets 9-15-9-19 Controls (see Controls) Hydraulics (See Hydraulic Systems) Lift Frame - 9-11 Return-to-Dig 9-11 ' Self-Leveling 9-9 Support Strut 9-11 Valve Guard 9-21 Valves (See Valves) Louvers-cab 9-133

M Manifold - intake/exhaust . 2-21 Master'Cylinder - brake and mounting... 7-7,7-11 Mats and Floor Plates 9-95 Mirror - rear view 9-113,9-1.47,9-149 Motor-wiper ,9-129,9-131 Mud Guard 9-101 Muffler - engine exhaust 2-11

N Nozzle - ether injection, cold start Nozzle - fuel injection Nozzle - windshield washers Numerical Index

2-13. 3-19 9-127 10-2

O Oil Cooler - engine Oil Cooler - hydraulic Oil Filter - engine Oil Filter - hydraulic Oil Pump and Pan Outlet - power plug..

2-29 6-21,8-9 2-29 8-125 2-31 4-21

P Pads - stabilizers Pan-oil Panel - cab control Panel - closure, rear - canopy Panel - engine side Panel - instrument, front and 'side.... Parking Brake Parking Brake - rear axle

9-45 2-31 9-125 9-97 9-91 4-23,4-25 7-13 7-5


580 Super L Series 2 Loader Bacl^hoe

1-10

ALPHABETICAL INDEX p Pedals Accelerator Brake Extendahoe Control Swing Pistons and Connecting Rods Plate - pump guard Plates - baffle, front covers Plates - floor and mats Plug - power outlet Precleaner Pulley Alternator Compressor Drive Crankshaft Fan and Water Pump Pump Engine Oil Fuel Injection Fuel Transfer Hydraulic Equipment Transmission Oil Water Windshield Washer Pump Guard R Radiator - engine Radiator Shroud Radio Ready Package Reflector - red Relays Reservoir Brake Master Cylinder Coolant Recovery Bottle Fuel Hydraulic Oil Radiator Windshield Washer Reservoir Lines - fuel Return-to-Dig Ride Control Roll Over Protective Structure Rotating Beacon

3-9 7-7 9-33 9-31 2-47 9-85 9-87,9-89 9-95 4-21 2-9 4-7 9-145 2-43 2-17 2-31 3-17 3-11 8-71 6-33 2-17 9-127 9-85

2-5 9-83 4-25,4-45,9-133 9-153 4-19 7-9 2-3 3-3 9-79 2-5 9-127 3-3 9-11 8-61,8-63 9-115,9-147 4-43

S Screen-Chaff Seat - operators Self-Leveling Control Sender Air Filter Restriction

Bur 7-3350

9-93 9-103 - 9-111 9-9 2-9

S Sender-Cont. Transmission Temperature 4-11 Water Coolant Temperature engine 4-11 Sensor - fuel level 3-3 Shift Lever - FNR - transmission 4-17 Shifter Mechanism - transmission 6-35 Shroud - radiator 9-83 Side Panels - engine 9-91 Slow Moving Vehicle Emblem 9-151 Solenoids Boom Lock 8-121 Coupler - quick, loader hydraulic tool 8-65 Four-Wheel Drive, transmission 6-51 Fuel Injection Pump 3-17 Ride Control 8-61 Speakers - radio and tape player 4-45 Spindles - front axle 5-15 Stabilizers 9-45 Starter - engine 4-3,4-5 Starter - mounting 4-9 Steering - two wheel drive Column 5-9 Control Valve 5-11 Cylinder 5-13 Hydraulic Circuit 5-5,5-7 Wheel 5-3 Steps 3-3,9-79 Stereo - radio 4-45 Sunvisor 9-115,9-147 Support Strut - loader lift frame 9-11 Switches Air Cleaner Restriction 2-9,4-11 Air Conditioning Control 9-125,9-141 Auxiliary Hydraulics - Backhoe 4-47 Auxiliary Hydraulics - Hand Held 4-21,8-43 Blower 9-125 Boom Lock 8-57 Brake Lamps 4-17,7-7 Clutch Cutout - gear shift lever handle 4-11 Cold Start 2-13 Coupler - quick, loader hydraulic tool 8-67 Declutch and Differential Lock 4-21 Differential Lock 4-21 Dome Lamp 4-17 Four Wheel Drive 4-21 High Pressure Cutout - air conditioner 9-143 Horn 4-17 Key and Starter 4-21 Lamps - driving, work and flood 4-21



1-11

ALPHABETICAL INDEX s

V

Switches-Cont. Lamps - hazard, flasher 4-17 Low Pressure - air conditioner 9-141 Oil Pressure 4-11 Parking Brake 7-5 Return-T6-big 4-11,9-11 Ride Control 8-63 Rotating Beacon 4-21 Seat - operators, limit 9-103 Temperature - engine coolant 4-11 Temperature Oil - rear axle 6-59 Transmission Control Solenoid 4-11,6-35 Transmission Shuttle Shift (FNR) 4-17 Turn Signal..... -4-17 Windshield Washer 9-127 Windshield Wiper. 9-129,9-131

Valves Auxiliary - Backhoe 8-51 Auxiliary - Hand Held.... 8-117,8-119 Backhoe Control Assembly - with extendable dipper, with auxiliary hydraulics 8-95 Assembly - with extendable dipper, without auxiliary hydraulics 8-93 Assembly - without extendable dipper, with auxiliary hydraulics 8-91 Assembly - without extendable dipper, without auxiliary hydraulics 8-89 Mounting 8-21 Sections Auxiliary Option 8-115 Boom 8-105,8-107 Bucket 8-99 Dipper 8-101 Dipper Extension 8-113 Inlet/Outlet 8-97 . Stabilizer 8-103 Swing 8-109,8-111 Loader Control Assembly - three spool 8-75 Assembly - two spool 8-73 Circuit Relief - bucket section 8-87 Guard - loader valve 9-21 Mounting 9-3 Sections Bucket 8-79 Clam 8-85 Inlet : 8-77 Lift 8-81 Outlet 8-83 Solenoid Valves Auxiliary Hydraulics - hand held 8-41 Boom Lock 8-121 Coupler- quick, loader tool..... 8-65 Differential Lock, rear axle 6-57 Four-Wheel Drive, transmission 6-51 Ride Control 8-61 Steering Control 5-11 Transmission Control 6-49 Valve Stem - wheel 5-19,6-53 Vents - louvers, cab 9-137 Visor-sun 9-115,9-147

T Tachometer - electric 4-27 Tank - fuel 3-3 Tank - hydraulic oil 9-79 Teeth - buckets 9-63 - 9-71 Thermostat - engine .....2^33 Throttle - engine .....'3-7,3-9 Tires and Wheels 5-19,6-53 Tool Box ,....9-81 Tool Coupler - quick disconnect 9-23 Tool Tray 4-25 Tower - backhoe control and covers ....9-25,9-27 Tower - swing 9-47 Transmission Cooling System.. 6-21 Dipstick 6-23 Filter-oil 6-27 Housing. 6-29,6-31 Idler and Primary Shaft 6-39 Input Shaft 6-41 Mounting 6-23 Output Shaft. 6-47 Pump - oil 6-33 Secondary Shaft 6-43,6-45 Shift Lever 6-23 Shifter Mechanism 6-35,6-37 Valve - control.... -6-49 Valve - solenoid 6-51 Turbocharger and System 2-23,2-25 Turn Signal Switch 4-17

W V

Valve Mechanism - engine

Bur 7-3350

.2-35

Washer - Windshield Wheel - steering Wheels and Tires Wiper - cab window

9-127 5-3 5-19,6-53 9-129,9-131


1-12

\


1-13

PICTORIAL INDEX EQUIPMENT HYDRAULICS HYDRAULIC PUMP TO OIL FILTER, C O N T R O L V A L V E S AND R E T U R N T O TANK REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

DESCRIPTION

PAGE

Suction hose at hydraulic tank Suction tube at hydraulic tank 1... Coupler hose : î. Suction tube at hydraulic equipment pump .........i Hose,at large pump section port Tube at tee to loader control valve inlet Loader valve to filter hose.. Hose at loader valve power beyond port to backhoe control valve inlet Hose at small pump section outlet port... Tube between small pump section hose to tube at backhoe valve outlet section Tube to inlet port on backhoe control valve outlet section Return hose at backhoe control valve to filter........ Oil filter to oil cooler tube Hose at oil cooler Oil cooler return hose Return to tank tube ; '. Return to tank hose Swing supply hose at loader valve inlet section lower port to backhoe valve swing section Pilot tube at backhoe valve swing section center port to loader control valve inlet section ; Signal hose at backhoe control valve swing section to loader control valve . inlet section

Bur 7-3350

••

8-3 8-3 8-3 8-3 8-3 8-3 8-5 8-7 8-7 8-7 8-7 8-9 8-9 .8-9 ^.8-9 8-9 8-9 8-39 8-39 8-39


1-14

B94100338

580 Super L Series 2 Loader Baclthoe

1-15

PICTORIAL INDEX

LOADER HYDRAULICS LIFT AND B U C K E T C Y L I N D E R S REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

DESCRIPTION

PAGE

Tube from upper lift.pqrt of loader control valve to rod end of left-hand lift cylinder Tube from lower lift port of loader control valve to closed end of right-hand lift cylinder Tube from lower lift port of loader control valve to closed end of left-hiand lift cylinder Tube from upper lift port of loader control valve to rod end of right-hand lift cylinder Hoses.at lift cylinder closed end Hose at upper port of control valve to lift cylinder rod end..... Tube at bucket section upper port Tube at bucket section lower port Hose at loader arm pivot Lower tube on right-hand lift arm from bucket section upper port to closed end of bucket cylinders Upper tube on right-hand lift arm from bucket section lower port to bucket cylinder rod end Rear crossover tube at upper liftframe tube to rod end of bucket cylinder... Front crossover tube at lower lift frame tube to bucket cylinder closed end Hose at bucket cylinders Tube at bucket cylinder rod end Tube to right-hand bucket cylinder closed end Tube at left-hand bucket cylinder closed end

Bur 7-3350

8-11 8-11 8-11 8-11 8-11 8-11 8-13 8-13 8-13 8-13 8-13 8-13 8-13 8-13 8-13 .8-13 8-13


1-16

LEFT-HAND CLAM CYLINDER

RIGHT-HAND CLAM CYLINDER

LOADER CONTROL VALVE

B9410028S


1-17

PICTORIAL INDEX LOADER HYDRAULICS CLAM CYLINDER REF. 1 2 3 4 5 6 7 8 9-

DESCRIPTION

PAGE

Tube at upper port auxiliary section of loader control valve to hose at loader arm pivot Tube at lower port auxiliary section of loader control valve to hose ati loader arm pivot Hose at loader arm pviot Lower tube on loader lift frarhe Upper tube on loader lift frame Tube at left-hand clam cylinder Tube at right-hand clam cylinder Right-hand and left-hand^clam cylinder hoses .V. J........ Lift arm:hoses: :

Bur 7-3350

8-17 8-17 8-17 8-17 8-17 8-19 8-19 8-19 8-19

: Issued February, 1998.

1-18

LEFT-HAND SWING CYLINDER BACKHOE CONTROL VALVE

RIGHT-HAND SWING CYLINDER

RIGHT-HAND STABILIZER CYLINDER

B9410026S


1-19

PICTORIAL INDEX

BACKHOE HYDRAULICS STABILIZER CYLINDER AND SWING CYLINDER REF. 1 2 3 4 5

DESCRIPTION

PAGE

Hose at stabilizer cylinder rod ends to backhoe control valve stabilizer section lower ports , Hose at stabilizer cylinder closed ends to backhoe control valve stabilizer section upper ports Hose at backhoe control valve swing section upper port to outer rod end of left-hand swing, cylinder : Hose at backhoe control valve swing sectibn lower port to outer rod end of right-hand swing cylinder ! ..A..... Crossover hose i

Bur 7-3350

8-21 8-21 ;

8-23 8-23 8-23


1-20

©

O IT

8 UJ

o

B9410030S


1-21

PICTORIAL INDEX BAGKHOE HYDRAULICS *BOOM, DIPPER, AND BUCKET REF. 1 2 3 4 • '5 6 7 8 9 10, 11 12 13 14 15 16 17

DESCRIPTION Hoses at control valve through swing tower to boom Tube to boom cylinder closed end hose Boom cylinder closed end hose Boom cylinder rod end tube Hose to boom' cylinder rod end tube Tube to boom cylinder rod end hose Hoses at control valve through swing tower to boom for dipper Tube to dipper cylinder closed end hose Hose at dipper cylinder closed end Hose at dipper cylinder rod end Tube to dipper cylinder rod end hose Hoses at control valve through swing tower to boom for bucket Tube.on right-hand side of boom, to bucl
PAGE 8-25 8-25 8-25 8-25 8-25 8-25 8-27 8-27 8-27 ...8-27 8-27 8-29 8-29 8-29 8-29 8-29 8-31

!;

* N P T E S : See page 1-23 for tubes and hoses used on models with extendable dipper.

Bur 7-3350


1-22

BUCKET CYLINDER

EXTENDABLE DIPPER CYLINDER

BACKHOE CONTROL VALVE

B9410027S

J

580 Super L Series 2 Loader Bacl
1-23

PICTORIAL INDEX BACKHOE HYDRAULICS EXTENDABLE DIPPER REF. 1 2 3 4 5 6 7 8 9 10 11 12

DESCRIPTION

PAGE

Hoses at control valve through swing tower to boom Tube on right-hand side of boom to bucket cylinder rod end hose Tube on left-hand side of boom to bucket cylinder closed end hose Hose to bucket cylinder rod end tube Hose to bucket cylinder closed end Bucket cylinder rod end tube - Hoses at control valve through swing tower to boom for extendable dipper circuit Tube on boom to extendable dipper cylinder rod end hose Tube on boom to-extendable dipper.cylinder closed end hose Hose at extendable dipper cylinder rod end tube Hose at extendable dipper cylinder closed end Tube at extendable dipper cylinder rod end

Bur 7-3350

8-33 8-33 8-33 8-33 8-33 8-35 8-37 8-37 8-37 8-37 8-37 8-37



2-1

A L P H A B E T I C A L INDEX ENGINE DESCRIPTION Air Cleaner and Air Intake Parts Air Cleaner Assembly Camshaft Cold Start System Cooler-Oil Cover - Gear, Front Crankshaft Cylinder Block.and Block Heater.... Cylinder Head and Valve Mechanism Cylinder Head, Cover, and Thermostat Engine Mounting Fan ; Filter-Oil : Flywheel and Housing Gasket Kits Heater Engine Block Engine Oil Manifold - Exhaust/Intake Muffler and Exhaust System Pan-Oil.. , Pistons and Connecting Rods Precleaner Assembly Pump : Oil..:: Wat^ Radiator and Mounting Parts Radiator Assembly Thermostat Turbocharger Assembly Turbdcharger System Wastegate Actuator

Bur 7-3350

PAGE 2-7 2-9 2-37 2-13 2-29 2-19 2-43 2-39,2-41 2-35 2-33 2-15 2-3 :2-29 2-45 2-49,2-51

'.

:

:

2-41 ...2-31 2-21 2-11 .....2-31 .2-47 2-9 :

:

,.

.

2-31 2-17 2-3 2-5 .2-33 2-25 2-23 .2-27


2-2

eg)

BT97M203

580 Super L Series 2 Loader Backhoe RADIATOR, FAN AND MOUNTING PARTS USED WITH 291288A1 HEAVY DUTY OIL COOLER REF. 1

PART NO. 239739A1

2 4

A170241 233272A1

5 6 7 8 9 10 11 12 13

•

186433A1 806-8016 895-15008 131084A1 1547924C1 806-8050 895-11008 132215A1 132218A1

14 15 16 17 18 19 20 21

132217A1 A171099 .232366A1 214-1432 141513A1 214-1440 217-92 121501A1

22 23 24 25 26 27 27 28 29 30 31

614-8016 814-10050 K691987 D52276 832-10410 185377A1 228133A1 814-10070 496-21041 A184545 J925953

33 34

614-8016 235040A1

35

235038A1

L I 26767

Bur 7-3350

DESCRIPTION RADIATOR ASSEMBLY - engine coolant, heavy duty, parts list page 2-5, used with 291288A1 heavy duty oil cooler, see page 6-21 for cooler and baffles CAP - radiator, 15 p s i . . . . SEAL - adhesive-backed, 6 (1/4) x 20 (25/32) x 404 mm (15-29/32 inch) long, radiator to shroud, upper and lower SHROUD-fan BOLT - heXi self-locking, 8 - 1 . 2 5 x 16.mm, class 10.9 WASHER - flat, 9 x 20 x 1.6 mm RESERVOIR - coolant recovery bottle CAP - recovery bottle BOLT - hex, self-locking, 8 - 1.25x 50 mm, class 10.9, . WASHER - flat, 9 x 17 x 1.6 mm SPACER - bottle HOSE - 591 mm (23-1/4 inch) long, coolant recovery, cut from L I 26767 hose HOSE - 1 2 5 mm (4-15/16 inch) long, coolant.overflow CLAMP - spring-type, hose, retaining . HOSE - radiator, upper CLAMP - adj, 1-9/16 - 2-1/2 inch dia . HOSE - radiator, lower. CLAMP - adj, 2-1/16 - 3 inch dia . . . . , V A L V E - d r a i n , 1/4 inch PT, drain . ! BRACKET - radiator mounting, lower, see page 9-83 for upper bracket that attaches to the radiator shroud. BOLT - hex, full threads, 8 - 1 . 2 5 x 16 mm BOLT - hex, 10 - 1 . 5 x 50 mm W A S H E R - f l a t , special INSULATOR - rubber, mount,, radiator NUT - hex, self-locking, 10 mm - 1 . 5 . . . FAN - engine cooling, without air conditioning.. ; FAN - engine cooling, 39 degree, with white identification dot BOLT - hex, 10 - 1.5 x 70 mrri WASHER - flat, 13/32 x 13/16 x 3/32 inch, hardened SPACER-fan BELT - fan, V-ribbed, alternator and fan, see page 9-145 for belt used on air conditioning compressor BOLT - hex, full threads, 8 - 1 . 2 5 x 16 mm, if used SEAL - foam, adhesive-backed, 20 (25/32) x 542 (21-11/32) x 6 mm (1/4 inch), horizontal, radiator to cooler. SEAL - foam, adhesive-backed, 20 (25/32) x 480 (18-29/32) x 10 mm (3/8 inch), vertical, radiator to cooler HOSE - bulk, 8 (5/16) ID x 2336 mm (92 inch) long

2-3

REQ'D.

1 1 2 1 4 4.. 1 1 2 4 2 1 1 3 1 .2 1 2 1 2 .4 .2 4 2 2 1 1 4 4 1 1 2 2 2 1


2-4

^ ^ ^ ^ ^ ^

BT97B260


2-5

RADIATOR A S S E M B L I E S REF.

1 2 3 4 5 6 7 -8 9 10 11

PART NO. 239739A1 175161A1 257434A1 175163A1 175162A1 175164A1 175165A1 614-8012 895-11008 A170241 NSS NSS

Bur 7-3350

DESCRIPTION RADIATOR ASSEMBLY - engine coolant, heavy duty, 5 row, used with 291288A1 heavy duty oil cooler, see page 6-21 for cooler TANK-upper CORE - radiator, 5 row. . . GASKET - core, upper and lower TANK - lower BRACKET - left-hand, radiator BRACKET - right-hand, radiator BOLT - hex, full threads, 8 - 1 . 2 5 x 12 mm WASHER - flat, 9 x 17 x 1.6 mm CAP - radiator, 15 psi SEAL - foam, side channel brackets, not shown SEAL - foam, corners, side channel brackets, not shown

REQ'D. 1 1 1 . . . . .2 . .1 V 1 8 '8 1 2 4


2-6

BT97N115


2-7

AIR C L E A N E R AND AIR INTAKE PARTS REF. 1 2 3 4 5 6 8 9 10 11 12 13 14 15

PART NO. 228120A1 293571A1 70973 614-8020 895-11008 829-1408 ; 223944A1 214-1456 275464A1 806-8025 895-15008 833-40408 L I 8337 214-1464

Bur 7-3350

DESCRIPTION PRECLEANER ASSEMBLY - air, parts list page 2-9 CLEANER ASSEMBLY - air, engine, parts list page 2-9 BAND - air cleaner mounting BOLT - hex, full threads, 8 - 1.25 x 20 mm WASHER - flat, 9 x 17 x 1.6 mm NUT - hex, 8 mm - 1 . 2 5 , class 10 . . . HOSE - air cleaner to engine CLAMP - adj, 3-1/16 - 4 inch dia PAD - heat and noise reduction. BOLT - hex, self-locking, 8 - 1.25 x 25 mm, class 10.9 WASHER - flat, 9 x 20 x 1.6 mm NUT - U-type, 8 mm - 1 . 2 5 STRAP - tie, 15 inch, barrier curtain CLAMP - adj, 3-9/16 - 4-1/2 inch dia

REQ'D. . .1 1 2 4 4 4 •, • • 1 2 1 4 4 • • •4 2 1


2-8

580 Super L Series 2 Loader Backhoe AIR C L E A N E R AND P R E C L E A N E R A S S E M B L I E S REF.

PART NO.

DESCRIPTION

2-9

REQ'D.

PRECLEANER ASSEIVIBLY 1 2 3 4

228120A1 NSS 277377R1 A42465 214-1464

PRECLEANER ASSEMBLY - air. BODY - precleaner BOWL - precleaner COVER - precleaner CLAMP - adj, 3-9/16 - 4-1/2 inch dia

AIR CLEANER ASSEIVIBLY

5 6 7 8 9 10 11

293571A1 226378A1 NSS. 222421A1 222422A1 247743A1 R21391 292740A1 D36264

Bur 7-3350

CLEANER ASSEMBLY - air, engine CLEANER ASSEMBLY - air, engine HOUSING - air cleaner. ELEMENT - primary ELEMENT - secondary •• • C O V E R - e n d cap CLAMP - air filter, housing to end cover, includes bolt SWITCH - air restriction ADAPTER - air restriction indicator


2-10

@

@


2-11

MUFFLER AND EXHAUST SYSTEM REF. 1 2 3 4 5 6 8 9 10

PART NO. 275967A1 176437A1 227293A1 A170467 225033A1 627-10030 896-11010 627-10030 829-1410

Bur 7-3350

DESCRIPTION PIPE - exhaust, muffler extension CLAMP - exhaust pipe to muffler, includes hardware MUFFLER - engine exhaust CLAMP - includes hardware, muffler tube to engine BRACKET - muffler, front BOLT - hex, full threads, 10 -1.5 x 30 mm, class 10.9 WASHER - flat, 11 x 21 x 2.5 mm, hardened BOLT - hex, full threads, 10 -1.5 x 30 mm, class 10.9 NUT - hex, 10 mm -1.5, class 10.9

REQ'D.

4 10 2 2


2-12

D

i.:)

R O T A T E D 180°

®

4

BS97B262


2-13

COLD START SYSTEM REF. 1

PART NO. A189154

2

D145367

3 4 5 6 7

222-615 NSS 222-650. 222-660 A171940 A172116

8 9 10

276-24916 D128402 A187923

11

495-11034 L72776

12 13 14 15 16 17 18

NSS H275784 D73741 174-93 L59682 LI 8337 254729A1

DESCRIPTION NOZZLE ASSEMBLY - cold start injector, .008 dual orifice nozzle, component parts not serviced seperately TUBE - 762 mm (30 inch) long, cut from L60539X bulk tube, valve to injector nozzle, see below ELBOW - 90 degree, compression, 1/8 tube OD x 1/8 inch PT BODY-elbow. SLEEVE - tapered, 1/8 inch tube OD NUT - hex, 1/8 tube OD x 5/16-24 inch CYLINDER - starting fluid, ether VALVE ASSEMBLY - cold start, 3 cc, starting fluid injection, component parts not serviced separately, mounts to inner left-hand chassis upright SCREW - self-tapping, hex head, 3/8 NC x 1 inch SLEEVE - wire guard, 380 mm (15 inch) long SWITCH - temperature, circuit breaking, includes lead wires, uses existing intake manifold mounting hardware WASHER-flat, 11/32 x 11/16 x 1/16 inch J SWITCH ASSEMBLY - push button, cold start, must also order (2) L59682 blade terminals (item 16) SWITCH - cold start NUT - hex, special NUT - hex, special SCREW - machine, round head slotted, No. 10 NF x 174 inch TERMINAL - blade, straight, use with L72776 switch STRAP - tie, 15 inch, nylon . . KIT - cap and cord, 1 inch threaded cap

L60539X

TUBE - bulk, nylon, 3 (1/8) ID x 4267 mm (168 inch) long

Bur 7-3350

REQ'D. 1 1 1 1 1 1 1 1 2 1 1 .1 1 . . : . .1 .1 1 2 2 UAR 1 1


2-14

a,

•»*•.

'.;r

•

. • '

•••••• >/,

^ .„;.^--

®

—

is)

B9408140S

®


2-15

ENGINE MOUNTING REF. 1 2 3 4 5 6 7 8 9

PART NO. 175637A1 814-12110 896-15012 A170309 814-12085 496-81018 117844A1 896-15012 832-10412

DESCRIPTION SUPPORT - engine, front BOLT -hex, 12 -1.75 X 110 mm WASHER - flat, 13.5 x 28 x 4 mm, hardened SPACER - engine mount, upper bolt holes BOLT-hex, 12- 1.75x85 mm WASHER - flat, 33/64 x 2 x 1/8 inch, hardened INSULATOR - engine mount, front WASHER-flat, 13.5x28 X 4 mm, hardened NUT-hex, self-locking, 12 m m - 1 . 7 5 . .

REQ'D. 1 4 4 2 2 4 2 2 ...2

NOTE: See page 6-21 for rear engine/transmission mounts.

Bur 7-3350


2-16

BT95G007

2-17

580 Super L Series 2 Loader Backhoe WATER PUMP S Y S T E M 4T-390 ElVIISSIONS CERTIFIED ENGINE REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

PART NO. J802358 NSS NSS 238-5341 J900227 J914462 J911205 J907769 J923044 100-21250 J910739 J911924 845-8040 845-8030 J925195 845-8025 . J925186 J918944 854-10070 A77817 NSS NSS NSS

Bur 7-3350

DESCRIPTION KIT - water pump PUMP ASSEMBLY - water PULLEY - water pump 0-RING - 3-1/2 ID X 3/16 inch wide BOLT - hex, special, 8 - 1.25 x 22 mm PULLEY-fan, 1.1 to 1 ratio SUPPORT - fan. BOLT - hex, special, 10 -1.5 x 70 mm, class 12.9 RETAINER - fan hub RING - internal retaining, No. 250 BEARING-ball HUB - fan BOLT - heavy hex flange, 8 - 1.25 x 40 mm BOLT - heavy hex flange, 8 - 1.25 x 30 mm BRACKET - belt tensioner. . BOLT - heavy hex flange, 8 - 1.25 x 25 mm SCREW - flat head cap, torx, special, 8 - 1.25 x 25 mm . . TENSIONER - belt BOLT - heavy hex flange, 10 -1.5 x 70 mm, class 10.9 KIT - belt tensioner pulley, used to replace pulley of J918944 belt tensioner, item 17 PULLEY- belt tensioner BOLT - pulley SEAL - dust

REQ'D.


2-18

2-19

580 Super L Series 2 Loader Backhoe FRONT G E A R C O V E R 4T-390 EMISSIONS CERTIFIED ENGINE REF. 1 2 3 4 5 6 7

PART NO. J918675 NSS J918673 J932120 J931351 845-8050 J924962

8

J924962

9 10 11 12 13 14 15 16 17 18 19 20 21 22

J900257 J919683 J915772 J907998 J903924 J913994 J904849 J929751 854-12025 J914868 J903463 J903475 J912772 845-8060

Bur 7-3350

DESCRIPTION COVER - gear, front SEAL - oil, crankcase front, order A77889 seal kit on page 2-43 . . . . GASKET - front cover HOUSING - timing gear GASKET - gear housing BOLT - heavy hex flange, 8 -1.25 x 50 mm BOLT - hex flange, special, 8 -1.25 x 16 mm, external, retains item 1 to item 4 BOLT - hex flange, special, 8 - 1.25 x 16 mm, internal, retains item 4 to block PIN - dowel, 16 mm long, locating HOUSING - timing pin RING - quad, timing pin housing SCREW - round head cap, torx, special, 5 - 0.8 x 17 mm PIN - timing O-RING - sealing RING - retaining, timing pin : GASKET - access cover plate BOLT - heavy hex flange, 12 - 1.75 x 25 mm, class 10.9 PLATE - access cover, flat COVER - front access, fuel pump drive gear SEAL - front access cover, fuel pump drive gear RETAINER - bolt BOLT - heavy hex flange, 8 - 1.25 x 60 mm

REQ'D.

10 8 5 2


2-20

BS96H021


2-21

MANIFOLDS

4T-390 EMISSIONS CERTIFIED ENGINE REF.-

PART NO.

DESCRIPTION

REQ'D.

EXHAUST 1 2 3

J901919 J905443 854-10065

MANIFOLD - exhaust GASKET - exhaust manifold

• • .1 4

BOLT - heavy hex flange, 10 - 1.50 x 65 mm, class 10.9

.8

INTAKE A77416 4 5 6 7 8

J904339 J907185 J906773 J918109 J931605

Bur 7-3350

KIT - intake manifold, no longer available, order components separately, items 4 - 6 COVER-intake PLUG - manifold WASHER-plug sealing . . . BOLT - hex flange, special, 8 -1.25 x 25 mm, intake manifold GASKET - intake manifold

1 .1 1 1 10 1


2-22

BT96H075

2-23

580 Super L Series 2 Loader Backhoe TURBOGHARGER SYSTEM 4T-390 EMISSIONS CERTIFIED ENGINE REF. 1 2 2A 3 4 5 6 7 8 9 10 11 12 13 14

15 16

'

PART NO. J931784 J931804 J933026 214-3240 REF J919369 J818823 J818824 .J913759 J903740 , J931350 '845-8020 J931970 214-1416 J919687

238-5013 222-993

Bur 7 - 3 3 5 0

DESCRIPTION

REQ'D.

T U B E - crossover H O S E - 5 8 mm (2-1/4 inch) long, air intake H O S E - 7 6 mm ( 3 inch) long, air intake

1 .1 1

C L A M P - adj, 1 -3/4 - 2-5/8 inch dia

- engine, new, see page correct assembly and component parts G A S K E T - tiirbocharger to manifold S T U D - turbocharger mounting N U T - hex flange, special, 1 0 mm - 1 . 5 , stud H O S E - turbocharger oil supply T U B E - turbocharger oil drain G A S K E T - turbo oil drain tube B O L T - heavy hex flange, 8 - 1.25 x 2 0 mm . H O S E - 7 6 mm ( 3 inch) long, turbocharger oil drain TURBOCHARGER ASSEMBLY

C L A M P - adj, 1 3 / 1 6 - 1 - 1 / 2 inch dia, hose:

4 2-25

for 1 1

4 -1 1

.1 . .2 1

.\ ......

- female hex, special ( 1 ) used to connect turbocharger oil supply hose to turbocharger, ( 1 ) used to connect turbocharger oil supply hose to J 9 1 8 9 5 4 oil filter head O - R I N G - 7 / 1 6 I D X 1 / 1 6 inch wide. G A S K E T - flare, copper, 3/8 inch tube O D . . .

2

ADAPTER

2 .1 2

Issued February, 1 9 9 8

2-24

580 Super L Series 2 Loader Backhoe TURBOCHARGER ASSEMBLY 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO. JR802798

J580234 *NSS NSS NSS *NSS NSS *NSS *NSS *NSS NSS *NSS *NSS NSS NSS *NSS * NSS NSS J531670 J535971 *J531582 *J531598 J535001 J527759 614-8020 J535800

DESCRIPTION KIT - turbocharger, engine, remanufactured. North America only, component parts shown on this page do not apply to the remanufactured assembly RETURN NUMBER - use this part number to return turbocharger core for credit when using a remanufactured assembly KIT - turbocharger, large frame, includes new turbocharger assembly, (1) J519807 turbo oil drain tube gasket and (1) J709861 turbocharger mounting gasket, not shown CENTER HOUSING ASSEMBLY - turbocharger NUT-hex, lock IMPELLER - turbocharger SEAL-plate SEAL - slit ring SLINGER-oil RING-snap BAFFLE-oil BEARING - turbocharger thrust COLLAR - thrust BEARING - turbocharger RING - retaining HOUSING - turbo bearing SHIELD - turbo heat SEAL - split ring SEAL - oil, not shown ROTOR ASSEMBLY - with shaft CLAMP - adjustable WASHER - flat, special NUT-hex BOLT-hex GASKET - adapter ADAPTER - connection BOLT - hex, full threads, 8 - 1.25 x 20 mm RING - snap

* J575205

KIT - overhaul, turbocharger, includes all items with an asterisk

JC537562 * * J802798 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15A 16 17 18 19 20 21 22 23 24

2-25

REQ'D. 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 1 1 1 1 1 1 1 1 1 1 1 5 1 1

* * NOTE: See items 1 -11 on page 2-27.

Bur 7-3350


2-26

2-27

580 Super L Series 2 Loader Backhoe W A S T E G A T E ACTUATOR 4T-390 EMISSIONS CERTIFIED ENGINE REF. 1 2 3 4 5 6 7 8 9 10 11

PART NO. J802798 J537560 .J528177 425-155 J528204 J528221 895-11008 J532195 814-8035 614-8020 J535203 NSS

Bur 7-3350

DESCRIPTION KIT - turbocharger, includes all parts shown below and on page 2-25 ACTUATOR - turbo wastegate. . LINK - adjusting N U T - h e x , jam, 5/16 inch NF NUT - lock RING - retaining WASHER-flat, 9 x 1 7 x 1 . 6 m m SPACER - mounting, short BOLT - hex, 8 - 1.25 x 35 mm . . . . . BOLT - hex, full threads, 8 - 1.25 X 20 mm . BRACKET - wastegate actuator HOUSING - turbine

REQ'D. 1 1 1 • •-1 2 • • -1 3 • • •I 1 2 1 1


2-28

B9311042S

580 Super L Series 2 Loader Backhoe OIL FILTER AND C O O L E R 4T-390 EMISSIONS CERTIFIED ENGINE REF. 1 2 3 3 4 5 6 7 8 9 10 11 12 13

PART NO. J918954 NSS J909355 J908616 J934429 J927622 845-8035 J918428 J925G09 J929457 J915787 J929792 J921557 J942914 J906619

Bur 7-3350

DESCRIPTION HEAD ASSEMBLY - oil filter and cooler H E A D - l u b e oilfiller ADAPTER - filter head FILTER - engine oil, cartridge, if used FILTER - engine oil, cartridge, premium oil filter, if used VALVE - relief, pressure BOLT - heavy hex flange, 8 - 1.25 x 35 mm PLUNGER - regulator, pressure SPRING - compression 0-RING-plug PLUG - threaded, pipe GASKET - filter head CORE - cooler, oil GASKET - oil cooler core P L U G - h e x , 1/8 inch PT

2-29

REQ'D.

14


2-30

2-31


OIL PUMP AND OIL PAN

4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO. JR930336 JG926202

1 2 3 4 5 6 7 8 9 10 11 12

, J930336 J900677 J905206 *J931349 845-8016 J901049 ; *NSS J924147 *J920773 J920400 J924148 **J902425 *A77673

DESCRIPTION REQ'D. PUMP - oil, remanufactured, North America only, component parts shown on this page do not apply to the remanufactured assembly. 1 RETURN NUMBER - use this part number to return pump core for credit when using a remanufactured a s s e m b l y . . . . PUMP - oil, engine, new BOLT - hex, full threads, 8 - 1.25 x 30 mm TUBE - suction, oil GASKET - mounting, oil suction .tube . ) BOLT - heavy hex flange, 8 - 1 : 2 5 x 16 mrh PAN - oil, engine GASKET - oil pan, order A77673 gasket kit for service. PLUG - hex magnetic, special, 12 mm - 1 . 5 , drain, oil WASHER - sealing, drain plug. . SCREW - hex flange cap, special, 8 - 1.25 x 25 mm 28 PLUG - hex magnetic, special, 22 mm - 1 . 5 , pipe, heater hole WASHER - sealing, plug KIT - gasket, oil pan, includes all items shown above with an asterisk

1

ENGINE OIL HEATER 13 14

**A77490 NSS 196466A1

KIT - heater, engine oil ELEMENT - heater, 120 volt CABLE - engine block heater

.1 1 1

* * NOTE: When engine oil heater kit is ordered, item 12, J902425 washer must also be ordered.

Bur 7-3350


2-32

2-33

580 Super L Series 2 Loader Backhoe CYLINDER HEAD C O V E R S 4T-390 EMISSIONS CERTIFIED ENGINE REF. PART N O . 1 , REF 2 J283333 2 J283336 2 J283338 J928404 3 4 J930906 5 J928406 6 . "J907049 7 '^v 'J908i18. 8 . '854-12030

DESCRIPTION.

REQ'D.

H E A D - cylinder, see page 2-35 for correct cylinder head; and parts l i s t . . . . . . . G A S K E T - head, standard G A S K E T - head, 2 notches, 0.25 m m overthick G A S K E T - head, 3 notches, 0.^0 mm overthick

A1 1 1

C O V E R - rocker arm

4

S E A L - rocker arm cover

4

I S O L A T O R - noise

4

B O L T - hex flange, special, 8 - 1.25 x 21.25 mm B R A C K E T - lifting, rear B O L T : - heavy hex flange, 1 2 - 1.75 x 30 mm, class 10.9 . . .

4 1 . . . . . . . .2

THERMOSTAT AND HOUSING 9 10 11 12 • 13 14 15 16

J9b3757 J914409 A77736 - J923331 NSS

845-8070 845-8035 J923387 845-8025

Bur 7-3350

B R A C K E T - lifting, front H O U S I N G - thermostat . . :

K I T - coolant thermostat . . . G A S K E T - therrriostat housing T H E R M O S T A T - coolant

B O L T - heavy hex flange, 8 - 1.25 x 70 m m B O L T - heavy hex flange, 8 - 1.25 x 35 mm S U P P O R T - alternator mounting B O L T - heavy hex flange, 8 - 1.25 x 25 mm

1 ::

1

1

1 1 -1

2 1 1 3


2-34

BT96H022

580 Super L Series 2 Loader Backhoe CYLINDER HEAD AND V A L V E MECHANISM 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART'NO. JR927330

JC927330 1 1 2 3

„ J927330 J917433 A77783 217-466

4 6 7 8 8A 9 ; 10 n

. ..J906619^ J900250 "•' J900299 J926700 J90i097 J921640 , J920867 J920868 J280911

12 13 14 15 16 17 17 18 19 20 21 22 23 . 24 25 26 27 28 29 30 31 32

J906854 J904105 *J904408 *J904409 *J9062p6 J9207t9 J920780 J922488 J900242 J900245 J910811 NSS J900706 425-116 J910810 NSS J900706 425-116 814-8075 J920781 J923262 J931623

DESCRIPTION HEAD ASSEMBLY - cylinder, remanufactured, North America only, component parts shown on this page do not apply to the remanufactured assembly RETURN NUMBER - use this part number to return head for credit when using a remanufactured assembly HEAD ASSEMBLY - cylinder, new, with valves. . HEAD ASSEMBLY - cylinder, new,- without valves PLUG - expansion, 21 mm OD . PLUG - square socket headless, 1/2 inch PT, one removedjto install temperature sending unit P L U G - h e x , 1/8 inch PT '. K E E P E R - valve RETAINER - valve spring SPRING-valve SEAL - valve stem . _ • SEAL - valve, intake VALVE-intake VALVE - exhaust PAD - wear, service repair only for valve stem tip, for use on intake and exhaust valves SEAT - insert, intake valve, service repair only SEAT - insert, exhaust valve, service repair only GUIDE - valve, intake, service repair only, 14 mm OD G U I D E - v a j v e , exhaust, service repair only, 1 4 r r i m O D . . GUIDE - valve, intake and exhaust, service repair only, 11 mm O D . . . BOLT - cylinder head, 70 mm long BOLT - cylinder head, 120 mm long SUPPORT AND SHAFT ASSEMBLY - rocker arm RING - retaining, rocker arm WASHER - thrust, rocker arm ARM ASSEMBLY - rocker, intake INSERT - rocker arm SCREW - slotted set, adjusting, special N U T - h e x , 3/8 inch NF ARM ASSEMBLY - rocker, exhaust INSERT - rocker arm SCREW - slotted set, adjusting, special N U T - h e x , 3/8 inch NF BOLT - hex, 8 - 1.25 x 75 mm BOLT - rocker arm and bylinder head, 180 mm long; ROD - push, rocker arm. TAPPET - valve, push rod

2-35

REQ'D.

1 1 1 1 3 . .5 2 16 8 ...8 A -4 • • -4 4 UAR 4 4 .4 4 .8 4 10 4 8 .8 4 1 1 1 4 . .1. 1 1 . . .4 4 8 8

• N O T E : These parts are semi-finished valve guides.

Bur 7-3350


2-36


2-37

CAMSHAFT

4T-390 EMISSIONS CERTIFIED ENGINE REF. 1 2 3 4 5 6 7

PARTNO. J929885 J940059 . *J903242 J927155 J900227 836-4065 J929028

DESCRIPTION CAMSHAFT - engine BUSHING - camshaft, front. BUSHING - camshaft, intermediate and rear, service repair only SUPPORT - thrust, camshaft. . . BOLT - hex, special, 8 - 1.25 x 22 mm KEY - Woodruff, 4 x 6.5 mm, camshaft gear GEAR - camshaft.

REQ'D. 1 1 4 1 .2 . .1 1

• N O T E : When the-intermediate and rear cylinder block camshaft bores are reamed in engine repair, order and install iterfi 3, J9G3242 bushings shown above.

Bur 7-3350


2-38

CD 0

a

BS97K164

2.39

580 Super L Series 2 Loader Backhoe CYLINDER B L O C K 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO. *236300A1 234277A2R

234277A1C 234277A2

JR933648

AC77752 J933648 1

J932012

2 3 4 5 6 6A 7 8

J900967 J900068 J927948 REF A77782 • A77505 J900956 41-1616 J933220 J900958 J900955 172599 J926047 J920706

9 10 11 12 12A 13 14 15 16 16A 17 17A 17B 17C 17D 17E

J900257 J902343 J900068 J678923 637-72081 A77429 * * J678921 * * J678912 * * J932296 * * J330478 **844-8016

DESCRIPTION ENGINE ASSEMBLY - 4T-39G Emissions Certified, complete, for service order 234277A2 basic engine b e l o w . . . ENGINE ASSEMBLY - basic, remanufactured. North America only, component parts shown on this page do not apply to the remanufactured assembly RETURN NUMBER - use this part number to return basic engine core for credit when using a remanufactured assembly ENGINE ASSEMBLY - basic, includes all parts except starter, alternator, fan, fan belt, air Gleaner, muffler, exhaust manifold, flywheel and housing, oil fill and dipstick, fuel injection pump, injectors and lines, front pulley, belt tensioner, turbocharger and aftercooler ' BLOCK ASSEMBLY - short, remanufactured. North America only, component parts shown on this page do not apply to the remanufactured assembly RETURN NUMBER - use this part number to return short block core for credit when using a remanufactured assembly ., BLOCK A S S E M B L Y - s h o r t , new, includes stripped block,, pistons, connecting rods and bearings, crankshaft and bearings BLOCK ASSEMBLY-stripped, engine, order J933220'block hardware kit showh below also CAP - main bearing. RING - dowel, 18 mm OD, main bearing cap to block BOLT - hex flange, main bearing cap, special . . . .j BUSHING - camshaft front, see page.2-37, item 2 PLUG - expansion, 58 mm OD PLUG - hex socket, 3/4 inch PT PLUG - expansion, 18 mm O D . . PLUG - cup, 1 inch diameter, expansion . KIT - block hardware, includes items 9 - 1 8 . , PLUG - expansion, 32 mrri OD PLUG - expansion, 10 mm OD PLUG - expansion, Welch, 60 mm OD O-RING - sealing, 57 mm ID .. i PLUG - expansion, 22 mm OD, not used in this application,; item 19, J9d3744 turbocharger oil drain tube is installed in this port PIN - dowel, 16 mm long, locating . : RING-dowel, 1 6 m m O D . T . . . . . . ; RING - dowei; 18 mm OD PLUG - hex socket, 10 mm O - R I N G - 8 . 1 ID x 1.6 mm wide, plug PLUG - hex socket, 1/2 inch PT v PLUG - hex socket, 14 mm, not shown O-RING - sealing, not shown PLUG - timing sensor hole, not shown. O-RING - sealing, not shown BOLT - heavy hex flange, 8 - 1.25 x 16 mm, not shown

REQ'D. 1

1 1

. .1

1 1 .1 1 5 10 10 1 1 1 3 2 1 2 1 1 1 . .1 2 2 2 3 1 1 1 1 1 , . .1 1

* NOTE: The engine part number is stamped'on a metal tag which is mounted on the front gear cover. * * N O T E : Items 17A - 17E are not used in this application. Continued on next page Bur 7-3350


2-40

0

2-41


CYLINDER B L O C K

4T-390 EMISSIONS CERTIFIED ENGINE REF. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

PART NO. J930139 J903744 J928759 845-8016 J925680 J283767 J907586 J905127 J904287 J934190 J906696 854-12025 A77424 J903102 J906697 854-10075 A77429 J918612 J904230 J928989

DESCRIPTION NOZZLE - piston cooling TUBE - turbocharger oil drain S E A L - cover bolt ' BOLT - heavy hex flange, 8 - 1 . 2 5 x 16 mm . COVER-tappet. •. GASKET - tappet cover BAFFLE - tappet cover TUBE - dipstick DIPSTICK - oil level gauge T U B E - o i l fill 0-RING - 3 8 mhi (1-1/2 inch) ID : BOLT - heavy hex fla:nge, 12 - 1.75 x 25 mm, class .10.9 . ; C A P - oil fill tube \ . . . . . . CONNECTION - water inlet. 0-RING - sealing, 50 mm ID ' BOLT - heavy hex flange, 10 - 1 . 5 x 75 mm, class 10.9 PLUG - hex socket, 1/2 inch PT HOSE - 360 mm (14-3/16 inch) long, breather CLAMP - spring, hose CiLIP - retaining

REQ'D. 4 1 4 2 • • • -1 1 1 1 -1 1 1 2 .1 •.1 1 3 • • . .2., 1 .1 1

ENGINE BLOCK HEATER 38 39 40

196803A1 NSS 196466A1 J910517

KIT - engine block heater. ELEMENT - engine heater, 120 volt CABLE - engine block heater O-RING - heater sealing.. :

1 .1 1 1

ENGINE OVERHAUL KIT 41 42 43 4445

A77887 J802747 J919053 A77465 A77405 A77406

46 47 48

A77870 J283333 A77'673.

Bur 7-3350

KIT - engine overhaul, includes items 41 - 48, not shown 1 KIT - piston, standard, see page 2-47 4 PIN - piston, see page 2-47 .4 KIT - bearing, upper and lower set, standard, see page 2-47 ..-. . . . . . . . . . . 4 BEARING - main, upper and lower set, standard, see page 2-43 . 4 BEARING - main thrust, upper and lower set, standard, see page 2-43 . •• 1 KIT - gasket, valve grind, see page 2-49 1 GASKET - head, standard, see page 2-33. 1 KIT - gasket, oil pan, see page 2-31 1


2-42


2-43

CRANKSHAFT 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO. JR908031

JC908031 1 2 3 4 5 6 7 8 9 10 11 11 11 11 11 12 12 12 12 12 12

J908031 J929027 J904483 NSS J9i4494 J905820 J903857 J921043 845-6015 J928493 A77405 / A77472 A77474 A77476 A77478 A77406 A77473 A77475 A77477 A77479 A77841;

12

A77840

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

A77889 NSS NSS NSS NSS A77890 NSS NSS NSS NSS A77809 NSS NSS A77810 NSS NSS

Bur 7-3350

REQ'D. DESCRIPTION CRANKSHAFT - engine, remanufactured, North America only, component parts shown on this page do not apply to the remanufactured assembly, for service order J908031 crankshaft assembly, item 1 RETURN NUMBER - use this part number to return crankshaft for credit when using a remanufactured assembly CRANKSHAFT ASSEMBLY - engine GEAR - crankshaft PIN-dowel SEAL - oil, crankshaft front, order item 13 kit PULLEY - crankshaft vibration damper FLANGE - adapter, pulley B O L T - h e x flange, special, 1 2 - 1 . 2 5 x 3 6 mm .; .4 RETAINER - seal, rear cover. . .1 BOLT - heavy hex flange, 6 - 1 .O x 15 mm 6 GASKET - rear cover retainer 1 BEARING - main, upper and lower set, standard 4 BEARING - main, uppenand lower set, 0.25 mm undersize 4 BEARING - main, upper and lower set, 0.50 mm undersize . .4 BEARING - main, upper and lower set, 0.75 mm undersize .4 BEARING - main,- upper and lower set, 1.00 mm undersize 4 BEARING - main thrust, upper and lower set, standard BEARING - main thrust, upper and lower set, 0.25 mm undersize . . . . BEARING - main thrust, upper and lower set, 0.50 mm undersize BEARING - main thrust, upper and lower set, 0.75 mm undersize BEARING - main-thrust, upper and lower set, 1.00 mm undersize . . . . BEARING - main thrust, upper and lower set, 0.50 mm undersize, 0.50 mrh oversize thrust / . BEARING - main thrust, upper and lower set, 1.00 mm undersize, 1.00 mm oversize thrust KIT - oil seal, crankshaft front SEAL - oil, front TOOL - installation TOOL - installation SHIELD - dust KIT - oil seal, crankshaft front, includes wear sleeve SEAL - oil, front SLEEVE - wear, not shown TOOL - installation SHIELD-dust KIT - oil seal, crankshaft rear TOOL - installation SEAL - oil, rear KIT - oil seal, crankshaft rear, includes wear sleeve i.. SLEEVE - wear ' S E A L - o i l , rear


2-44

B9501053S


2-45

FLYWHEEL AND HOUSING 4T-390 EMISSIONS CERTIFIED ENGINE REF. . 1 2 3 4 5 6 7 . 8 9 10 11 12 13 14

PARTNO. J930886 854-12040 J925234 613-8016 J912473 J910248 238-5212 J922595 NSS NSS NSS J913689 353-225 J904361 J901395

Bur 7-3350

DESCRIPTION HOUSING - flywheel BOLT - heavy hex flange, 12 - 1.75 x 40 mm, class 10.9 PLATE - cover BOLT - hex, 8 - 1 . 2 5 x 1 6 mm, retaining plate. 0-RING - flywheel housing to block PLUG - flywheel housing 0-RING - 7/8 ID X 1/8 inch wide, sealing PLATE ASSEMBLY - flex GEAR - ring, flywheel PLATE-flex NUT - sealing ADAPTER - crankshaft PLUG - slotted hex, 3/4 inch NF RING - clamping BOLT - hex, special, 12 - 1.25 x 32 mm

REQ'D. 1 .8 • • 2 1 1 1 .1 1 1 • -6 1 1 .1 .8


2-46

<3)


2-47

PISTONS AND CONNECTING RODS 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO.

REQ'D.

DESCRIPTION

PISTONS

1 2 3 4 5 6

J802747 J802746 NSS NSS NSS NSS
1 2 3 4 5 6

^ J802764 h ••J802422 NSS , NSS NSS NSS J901706 J919053

KIT - piston, 0.5 mm oversize KIT - ring, 0.5 mm oversize RING - compression, top RING - compression,.middle... RING - oil, bottom . .' P I S t O N - cylinder, 0.5 mm oversize RING-snap . PIN - piston

4 1 1 1 1 .1 ..2 1

1 2 3 4 5 6

J802765 J802423 NSS NSS NSS . NSS J901706 J919053

KIT - piston, 1.0 mm oversize KIT - ring, 1.0 mm oversize RING - compression, top RING - compression, middle RING - oil, bottom PISTON - cylinder, 1.0 mm oversize RING-snap. . PIN - piston

• .4 1 .1 1 .1 • .1 2. 1

7

J904166

KIT - piston, standard KIT - ring, standard RING - compression, top RING - compression, middle. RING - oil, bottom PISTON - cylinder, standard RING - snap PIN - piston

4 .1 .1 1 1 1 -2 1

LINER - piston, used only in engine blocl< repair (When liner is installed, use J802747 standard piston kit).

UAR

CONNECTING RODS JR942581

JC901569

8 9

J942581 NSS J941476 J900919 A77465 A77466 . A77467 A77468 A77469

Bur 7-3350

ROD ASSEMBLY - connecting, remanufactured, North Anrierica only, component parts shown on this page do not apply to the remanufactured assembly RETURN NUMBER - use this part number to return connecting rod for credit when using a remanufactured assembly . ROD ASSEMBLY - connecting, new, includes both halves ROD - connecting. BUSHING - connecting rod BOLT - hex, special .;. KIT - bearing„upper and lower set, standard KIT - bearing, upperrand lower set, 0.25 mm oversize KIT - bearing, upper and lower set, 0.50 mm oversize . . .; KIT - bearing, upper and lower set, 0.75 mm oversize K I T - b e a r i n g , upper and lower set, 1.00 mm oversize . . ,

1 1 .4 1 1 2 4 4 4 4 4


2-48

^3)

^5=

®


2-49

GASKET KIT 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO.

REQ'D.

DESCRIPTION

VALVE GRIND 1 2 2 3 4 5 6 8 9 10 11 12 13 15

* A77870 J923331 J901097 J921640 J919369 J905443 J931605 J931350 J930906 J903380 J906659 J909356 J914856 J823921 J928406

KIT - gasket, valve grind GASKET - thermostat housing SEAL - valve, intake, identified by color black with orange band SEAL - valve, intake, identified by color orange with silver band GASKET - turbocharger to manifold GASKET - exhaust manifold GASKET - intake manifold GASKET - turbo oil drain tube SEAL - rocker arm cover SEAL - connector, fuel drain manifold tube SEAL - injector nozzle, 7 mm injector tip 0-RING - sealing, body to nut GASKET - air crossover connection GAUGE - cylinder head, bolt length ISOLATOR - noise, rocker arm cover

1 1 4 4 1 4 1 1 4 4 4 4 1 1 4

* NOTE: When just the valve grind gasket kit is used, also order the required cylinder head gasket, item 2, page 2-33.

Bur 7-3350


2-50

J',

BT96H199


2-51

GASKET KIT 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO.

REQ'D.

DESCRIPTION

CYLINDER BLOCK 1 2 3 . 4 5 • 6 7. 8 9 10 11 12 13 14 15 16 17 18 19

*A77864 J903475 d918673 J931351 J915772 J913994 J929751 238-5341 J283767 J928493 J906697 J942914 J929792 J902425 J906696 J929457 J912473 J931348 J928759 J930993

KIT - gasket, cylinder block SEAL - front access cover .. GASKET - front cover, to housing GASKET - gear housing, timing . RING - quad, timing pin housing - 0-RING - sealing, timing pin . . . . . . GASKET access cover plate, accessory drive 0-RING 3-1/2 ID X 3/16 inch wide, .water pump to cylinder block GASKET tappet cover GASKET rear cover retainer, crankshaft O-RING sealing, 50 mm ID, water inlet connection ..:. GASKET oil cooler c o r e . . . . GASKET filter head, oil WASHER sealing, plug, oil pan 0-RING - 38 mm (1-1/2 inch) ID, engine oil fill tube O - R I N G - o i l filter plug 0-RING - flywheel housing to b l o c k . . . . GASKET - mounting, fuel transfer pump S E A L - c o v e r bolt O-RING - sealing

4 .1

* NOTE: For complete engine overhaul, order 1 - cylinder block kit, 1 - valve grind kit on page 2-49,1 - oil pan kit on page 2-31, 1 - front and rear.crankshaft seal kit on page 2-43 and the required cylinder head gasket on page 2-33.

Bur 7-3350


2-52


3-1

ALPHABETICAL INDEX FUEL SYSTEM DESCRIPTION Cover - Loader Lift Frame Tubing Filter Fuel Reservoir Fuel Reservoir Lines Injection System Nozzle - Injection Pump and Drive - Injection Sensor - Fuel Level Throttle Control Linkage Foot Controls Hand Control

Bur 7-3350

PAGE 3-3 3-11 3-3 3-3,3-5 3-13 3-19 3-17 3-3

:.

3-9 3-7


3-2

®

C23)

BT97N162

^


3-3

FUEL RESERVOIR AND FUEL LEVEL SENSOR REF. 1

PART NO. 284041A3

1A

281819A4

2 3 3A 4 5 6

627-20040 302358At 896-11020 •185926A1 130049A1 218-5211 ,

6A •7 8 10 10 11 12 13 "14 15 16 17 18 19 20

237-6010 214-1708 214-1704 284431A1 298463A1 188311A2 D75465 196252A1 234892A1 130047A1 515-23127 121856A1 1348264C1 234888A1 284452A2

21 22 23 24 25

130048A1 L I 8337 194i99A1 217-372 196247A1

27

490-11010

28 29

D83885 189602A1

29A

188009A1

DESCRIPTION REQ'D. TANK - fuel reservoir, 31 gallon, includes left-hand steps, mounts to left-hand side of'Chassis, also includes Ref 6 plug 1 TANK - fuel reservoir, 40 gallon, optional, includes left-hand steps, mounts to left-hand side of chassis, includes Ref 6 plug, if used, not shown 1 BOLT - hex, full threads, 20 - 2.5 x 40 rrim, class 10.9 4' WASHER - flat, hardened,,special 2 WASHER - flat, 22 x 37 x 4 mm, harderied 2 SPACER - bushing, left-hand side of tank. 2 CAP - fuel tank, non-vented 1 PLUG - hex socket, 7/8-14 inch Ofring boss, drain, included with Ref 1 or 1A fuel tank 0-RING - 3/4 ID X 3/32 inch wide CLAMP - adj, 1/2 - 29/32 inch dia CLAMP - ad], 1/4 - 5/8 inch dia, center hose SENSOR - fuel level, 31 gallon tank, Ref 1 SENSOR - fuel level, 40 gallon tank, Ref 1A GASKET - fuel sensor SCREW - self-tapping, hex washer head, special. No. 10 NF x 5/8 inch CLAMP-hose HOSE - 1 1 0 0 mm (43-5/16 inch) long, vent VENT - fuel, 1/4 inch PTF short, CLAMP - P-type, 1/2 inch ID BOLT - hex washer, special, 10 - 1 . 5 x 30 mm CLAMP - hose, 3/8 inch HOSE - 1280 mm-(50-7/16 inch) long,.fuel supply, to fuel lift pump HOSE - 1900 mm (74-13/16 inch)-long, fuel return, attaches to injector return line on engine i . SLEEVE - 203 mm (8 inch) long, fuel line hose guard STRAP - tie, 15 inch, nylon, retaining UAR F I L T E R - f u e l , in-line ELBOW - 90 degree, 1/2 stem end x 1/4 inch PT, to engine fuel lift pump HOSE - 13 (1/2) X 20 (25/32) x 78 mm (3-5/64 inch) long, fuel filter to lift pump pump SCREW - machine, pan Phillips, No. 10 NF x 5/8 inch, fuel sensor nrr»iinH ground WASHER - flat, copper, special COVER - left-hand loader lift frame tubing, mounted above fuel reservoir, models without clam bucket or auxiliary h y d r a u l i c s . . . COVER - left-hand loader lift frame tubing, mounted above fuel reservoir, models with clam bucket, not shown Continued on next page

Bur 7-3350

lssued:February, J 998

3-4

@

- ^

BT97N162

(13)

^


3-5

FUEL RESERVOIR AND FUEL LEVEL SENSOR REF. 30 31 32 34 35 37 38 39

PARTNO. * 191046A1 614-8016 895-15008 895-11010 829-1410 D40442 814-10045 307348A1

DESCRIPTION REQ'D. TRIM - edge, 650 mm (25-19/32 inch) long, cut from A165860 bulk trim : 1 B O L T - h e x , full threads, 8 - 1 . 2 5 x 1 6 mm 1 WASHER - flat, 9 x 20 x 1.6 mm 1 WASHER - flat, 11 X 20 x 2 mm 1-2 N U T - h e x , 10 mm - 1 . 5 , class 10.9, 189602A1 cover 1 TRIM - edge, 305 mm (12 inch) long, cut from F42827 bulk trim 1 BOLT - hex, 10 - 1.5 x 45 mm 1 PAD - antj-skid, 700 mm (27-9/16 inch) long.. ....2

A165860

TRIM - edge, bulk, 696 mm (27-3/8 inch) long

F42827

TRIM - edge, bulk, 2946 mm (116 inch) long

1 UAR

* N O T E : Apply 75 mm (3 inch) of trim to front lower edge and 570 mm (22-7/16 inch) of trim to outside lower edge of cover.

Bur 7-3350


3-6

580 Super L Series 2 Loader Backhoe T H R O T T L E CONTROL LINKAGE HAND CONTROL REF. 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16

PART NO. 305067A1 A177435 814-12045 896-11012 D148962 496-81018 832-10412 495-31022 432-48 121335A1 LI 8337 225-14210 213-123 427-3058 432-48

Bur 7-3350

DESCRIPTION LEVER - hand throttle KNOB - lever, lever BOLT - hex, 12 - 1.75 x 45 mm WASHER - flat, 13.5 x 24 x 3 mm, hardened . . WASHER - Belleville WASHER - flat, 33/64 x 2 x 1/8 inch, hardened. NUT - hex, self-locking, 12 mm -1.75 WASHER - flat, 7/32 x 1/2 x 3/64 inch PIN-cotter, 1/16x1/2 inch CABLE - control, hand throttle STRAP - tie, 15 inch, nylon, retaining NUT - hex, No. 10 NF CLEVIS - adjustable, No. 10 NF PIN - clevis, 3/16 x 9/16 inch, hardened PIN-cotter, 1/16x1/2 inch

3-7

REO'D.


3-8

@ .1""'

BT97M155

580 Super L Series 2 Loader Backhoe T H R O T T L E CONTROL LINKAGE FOOT CONTROLS REF. 1 2 2A 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

PART NO. 282242A1 132931A1 189109A1 282931A1 255291A1 256776A1 895-11005 800-435 D124857 814-8050 892-11008 895-11008 123558A1 123392A1 245287A1 302846A1 838-3640 213-123 427-3058 432-48 225-14210 275454A1 275456A1 614-8025 892-11008 275455A1 627-12030 892-11012 278183A1 275457A1 492-11025 425-154 614-6016 892-11006 895-11006

Bur 7-3350

DESCRIPTION PEDAL - accelerator, plastic BOOT -1/2 inch rod, accelerator pedal rod RETAINER - boot spring ROD - accelerator pedal shaft PIN - throttle pedal SPRING - 1/16 X 1/2 inch WASHER - flat, 5.5 x 10 x 1 mm RING - E-type, external retaining, No. 5 BLOCK - cross shaft BOLT - hex, 8 - 1.25 x 50 mm WASHER - lock, 8 mm WASHER - flat, 9 x 17 x 1.6 mm SPRING - throttle return SPACER - spring retaining BRACKET - spring return LEVER - throttle control PIN - roll, 6 X 40 mm CLEVIS - adjustable. No. 10 NF PIN - clevis, 3/16 X 9/16 inch, hardened PIN-cotter, 1/16x1/2 inch NUT-hex, No. 10NF CABLE - throttle, to injection pump BRACKET - throttle, mounts on firewall weld nuts BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - lock, 8 mm BRACKET - throttle BOLT - hex, full threads, 12 -1.75 x 30 mm, class 10.9 WASHER - lock, 12 mm JOINT-ball BAR - throttle lever WASHER-lock, 1/4 inch NUT-hex, jam, 1/4 inch NF BOLT - hex, full threads, 6 -1.0 x 16 mm WASHER - lock, 6 mm WASHER - flat, 6.6x12 X 1.6 mm

3-9

REQ'D.

2 2 4 4 4 4 1 1 1 1 1 1 1 1 1 1 1 2 2 1 2 2 1 1 1 1 2 2 2


3-10

580 Super L Series 2 Loader Backhoe F U E L FILTER AND T R A N S F E R PUMP 4T-390 EMISSIONS CERTIFIED ENGINE REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 .-

19 20 21

. •

PART NO. J925955 J931062 J914284 J931348 J933254 845-8025 J917280 J918191 J918188'J916361 J924726 J927633 J933250; J918192 J932096 ) J932035 J924725 J918192 J90586d . J911446' 'J905403 844-8025

Bur 7-3350

DESCRIPTION ADAPTER-fuelfilter. . : FILTER-fuel SPACER - fuel transfer pump mounting GASKET - mountirig, fuel transfer pump PUMP - fuel transfer BOLT - heavy hex flange, 8 - 1.25 x 25 mm TUBE-supply WASHER - sealing, special, 1 2 x 1 8 x 1 mm. WASHER-sealing BOLt - banjo connector, 12 - 1.5 x 24 mm VALVE-check TUBE - manifold, fuel BOLT - banjo connector. WASHER - sealing, special, 14 x 20 x 1 mm VALVE - overflow TUBE - supply, fuel BOLT - banjo-Connector WASHER-sealing,special, 1 4 x 2 0 x 1 mm BOLT ASSEMBLY - banjo hex, special BOLT - banjo connector, 12 - 1.50 x 24 mm . SCREW - hex, special, vent BOLT - heavy hex flange, 8 - 1.25 x 25 mm

3-11

•

REQ'D. 1 1 1 1 1 .2 1 .4 .2 1 1 1 1 2 .1 ^. .1 1 .2 .1 1 1 1


3-12

J

6

580 Super L Series 2 Loader Backhoe F U E L INJECTION S Y S T E M 4T-390 EMISSIONS CERTIFIED ENGINE REF.

P A R T NO.

1 2 3 4 5 6 7• 8 9 10 11 12 13 14 15 16 17 18

J930152 J929393 J929394 J929395 J929396 J927633 J903380 J905307 J929490 J906659 J920414 J917746 J904711 J920854 J917717 J918785 J918786 J918784

Bur7-3350

DESCRIPTION P U M P A S S E M B L Y - fuel injection, parts list page 3-17 T U B E - fuel injector, No. 1 cylinder T U B E - fuel injector, No. 2 cylinder T U B E - fuel injector. No. 3 cylinder T U B E - fuel injector, No. 4 cylinder T U B E - manifold, f u e l . . . . ." S E A L - connector B O L T - banjo drain, special N O Z Z L E A S S E M B L Y - fuel injectibn, parts list page 3-19 S E A L - injector nozzle, 7 mm injector tip. . ;

B R A C E - f u e l tube C L A M P - f u e l tube B R A C K E T - f u e l tube . . . . :. B O L T - hex, captive washer, special, 5 ^"0.8 x 20 mm B R A C K E T - f u e l tube BRACE-tube .. C L A M P - vibration BRACE-tube

3-13

REQ'D:

4 4 4 4 8 . . . .4 7 2 1 2 1


3-14

0

580 Super L Series 2 Loader Backhoe ANEROID AND W A S T E G A T E S Y S T E M 4T-390 ElVIISSIONS CERTIFIED ENGINE REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14

PART NO. J537560 214-1404 J926113 J920344 J920348 825-2408 221-87 J282406 217-281 222-41 J926738 J919644 J903035 J918191

Bur 7-3350

3-15

DESCRIPTION ACTUATOR - turbo wastegate, see page 2-27 for mounting of actuator CLAMP - adj, 1/4 - 5/8 inch dia HOSE - 466 mm (18-3/8 inch) long, aneroid to wastegate STUD - valve cover and hose, wastegate actuator mounting CLAMP - hose NUT - hex flange, 8 mm -1.25 REDUCER - pipe, 1/2 male x 1/8 inch female TEE -1/8-27 str thread x fem str thread x fem str thread ELBOW - 45 degree, 1/4 barb end x 1/8 inch PT ELBOW - 90 degree, compression, 3/16 tube OD x 1/8 inch PT TUBE - aneroid, nylon CONNECTOR - banjo BOLT - banjo hex, 12 -1.5 x 24 mm WASHER - sealing, special, 12 x 18 x 1 mm

REQ'D. 1 2

2


3-16

C) G

0

(27A)

580 Super L Series 2 Loader Backhoe F U E L INJECTION PUMP AND DRIVE 4T-3g0 EMISSIONS CERTIFIED ENGINE REF.

PART NO. JR930152

JC930153 1 2 3 4 6 7 8 9 10 13 14 17 18 19 20 21 22 23 24 25 26 27 27A 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

J930152 A77720 J928981 J912888 J932096 933697R1 691292C1 680187C1 1808728C1 A77775 A41852 1808822C1 895-11006 892-11006 829-1306 628-6016 J931450 J915036 825-2410 J918536 A77512 J941472 637-72081 J933291 218-752 J932529 NSS NSS NSS NSS NSS NSS J930993 J930590 845-6012 J929456 J802998 NSS 832-41306 J934022

Bur 7-3350

3-17

DESCRIPTION REQ'D. PUMP ASSEMBLY - fuel injection, remanufactured, North America only, component parts shown on this page do not apply to the remanufactured assembly, for service order J930152 pump assembly, item 1 "I RETURN NUMBER - use this part number to return pump core for credit when using a remanufactured assembly PUMP ASSEMBLY - fuel injection PIN - timing WASHER - lock, timing plug PLUG - timing VALVE - overflow WASHER - valve sealing HOUSING - spring return 0-RING - sealing, special LEVER - throttle control WASHER - lock NUT - hex, self-locking BOLT - throttle lever WASHER - flat, 6.6 x 12 x 1.6 mm WASHER - lock, 6 mm NUT - hex, 6 mm -1.0, class 10 BOLT - hex, full threads, 6 -1.0 x 16 mm, class 10.9 GEAR - fuel pump STUD - pump mounting 4 NUT - hex flange, 10 mm -1.5 4 HOSE - flexible ELBOW - 90 degree NIPPLE - hex, 7/16-20 inch flare x 10 -1.0 mm str thread O-RING - 8.1 ID X 1.6 mm wide TEE - 7/16-20 flare x flare x fem swivel CAP-hex, 7/16-20 inch SOLENOID - fuel shutoff, 12 volt SPRING - return, plunger STRAP - tie, boot to solenoid BOOT - protective, plunger NUT - hex, jam WASHER - lock JOINT - ball O-RING - sealing BRACKET - solenoid mounting BOLT - heavy hex flange, 6 -1.0 x 12 mm BOLT-hex, 1 6 - 2 . 0 x 1 2 mm KIT - pump shutoff lever LEVER - pump shutoff NUT - hex, self-locking, 6 mm -1.0, class 10 WASHER - flat, special


3-18

© — ®

B920892S

3-19

580 Super L Series 2 Loader Backhoe F U E L INJECTION NOZZLE 4T-390 EMISSIONS CERTIFIED ENGINE REF.

PART NO. JR929490 JC929490

1 2 3 4 5 6 7 8 9 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

J929490 J909356 *J906659 NSS NSS NSS NSS NSS NSS 1806233C1 1806234C1 1806235C1 1806236C1 1806237C1 1806238C1 1806239C1 1806240C1 1806241 CI 1806242C1 1806243C1 1806244C1 1806245C1 1806246C1 1806247C1 1806248C1 1806249C1 1806250C1 1806251C1 1806252C1 1806253C1 1806254C1 1806255C1 1806256C1 1806257C1 1806258C1 1806259C1 1806260C1 1806261 CI 1806262C1

DESCRIPTION NOZZLE ASSEMBLY - fuel injection, remanufactured. North America only, component parts shown on this page do not apply to the remanufactured assembly RETURN NUMBER - use this part number to return nozzle assembly core for credit when using a remanufactured assembly NOZZLE ASSEMBLY - fuel injection 0-RING - sealing, body to nut SEAL - injector nozzle, 7 mm injector tip BODY - injector SPRING - nozzle pressure SEAT - nozzle pressure spring STOP - nozzle valve TIP - nozzle injector NUT - cap, nozzle tip SHIM nozzle, 1.00 mm SHIM nozzle, 1.04 mm SHIM nozzle, 1.08 mm SHIM nozzle, 1.10mm SHIM nozzle, 1.14mm SHIM nozzle, 1.18mm SHIM nozzle, 1.20 mm SHIM nozzle, 1.24 mm SHIM nozzle, 1.28 mm SHIM nozzle, 1.30 mm SHIM nozzle, 1.34 mm SHIM nozzle, 1.38 mm SHIM nozzle, 1.40 mm SHIM nozzle, 1.44 mm SHIM nozzle, 1.48 mm SHIM nozzle, 1.50 mm SHIM nozzle, 1.54 mm SHIM nozzle, 1.58 mm SHIM nozzle, 1.60 mm SHIM nozzle, 1.64 mm SHIM nozzle, 1.68 mm SHIM nozzle, 1.70 mm SHIM nozzle, 1.74 mm SHIM nozzle, 1.78 mm SHIM nozzle, 1.80 mm SHIM nozzle, 1.84 mm SHIM nozzle, 1.88 mm SHIM nozzle, 1.90 mm SHIM nozzle, 1.94 mm SHIM nozzle. 1.98 mm

REQ'D. 4 4 4

UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR UAR

* NOTE: Whenever a nozzle is removed from the cylinder head, J906659 seal must be replaced before nozzle is installed in cylinder head.

Bur 7-3350


3-20


4-1

A L P H A B E T I C A L INDEX ELECTRICAL DESCRIPTION Alarm - Backup Alternator Alternator Mounting Antenna - Radio Batteries and Cables Models with Cold Start Models without Cold Start Beacon - Rotating Cluster - Instrument Consoles - Instrument Electrical Circuits Auxiliary Hydraulics - Backhoe Engine Front Console Side Console Tractor Lamp - Cab Tractor Lamp - Canopy Harness - Electrical Adapter-Cab Adapter - Engine Auxiliary Hydraulics - Backhoe Auxiliary Hydraulics - Hand Held Cab Canopy Clutch Cutout Transmission Gear Shift Loader Control Lever Engine Front Console Horn Optional Equipment - Side and Chassis Radio Side Console Horn Instrument Cluster Instrument Panel and Covers - Front Instrument Panel and Covers - Side Lamps - Cab Lamps - Canopy Outlets - Power Plug Radio Ready Kit Starter Starter Mounting Tape Player

Bur 7-3350

PAGE 4-41 4-7 4-9 4-45 4-15 4-13 4-43 4-27 4-23,4-25 4-47 4-11 4-17 4-19,4-21 4-31 4-29 4-19 4-19 4-47 4-21 4-31 4-29 4-11 4-21 4-11 4-17 4-41 4-19 4-45 4-19,4-21 4-41 4-27 4-23 4-25 4-35,4-39 4-33,4-37 4-21 4-45 4-3,4-5 4-9 4-45


4-2

0

B9408147S

580 Super L Series 2 Loader Backhoe STARTER REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

PART NO. 1987559C1 A46948 104588A1 NSS NSS NSS NSS NSS 1546500C1 A47243 A47128 892-11006 495-81252 A47127 104587A1 211-1311 A47232 A47233 A47234 A47235 A47236 A47240 NSS NSS NSS NSS NSS NSS A47241

4-3

DESCRIPTION STARTER ASSEMBLY - engine, new HOUSING - drive end SWITCH ASSEMBLY - magnetic, includes items 4-8 SOLENOID - switch GASKET - solenoid cover COVER - solenoid SCREW - cover to switch WASHER - cover screw 0-RING - switch to housing BOLT ASSEMBLY - through BOLT - tie, starter, through WASHER - lock, 6 mm WASHER - fiat, 1/4x9/16x1/16 inch 0-RING - bolt seal CLUTCH - drive BALL - chrome alloy steel, 11/32 inch, grade 200 SPRING - compression, 2-13/16 inch free length, clutch drive PINION-idler WASHER - thrust, idler pinion ROLLER - pinion bearing, idler RETAINER - roller bearing HOUSING ASSEMBLY - with coil and brushes HOUSING - starter COIL - field BRUSHES - starter SHOE - pole SCREW - pole shoes BOOT - magnetic switch terminal PLATE-lock

REQ'D.

2 4 4 1 1

Continued on next page

Bur 7-3350


4-4

0

-J

®

B9408147S

580 Super L Series 2 Loader Backhoe STARTER REF. 28 29 30 31 32 33 34 35

PART NO. REF A47242 452698C1 A47247 A47239 A47249 A47237 A47238 A47244

36 37 38 39 40 42 43 44 45

A47230 A47129 195-2015 A47130 A46950 892-11005 892-11010 825-1410 A10454 104589A1

Bur 7-3350

4-5

DESCRIPTION STARTER ASSEMBLY - engine (continued from previous page). ARIVIATURE ASSEMBLY - starter BEARING - ball BEARING - drive end HOLDER ASSEMBLY - brush (Includes 2 brushes) SPRING - brush tension FRAME - commutator end COVER - end frame SCREW ASSEMBLY - with washer, brush retaining, brush holder to cover BOLT ASSEMBLY - commutator end cover to drive end housing BOLT ASSEMBLY - with washer WASHER - fiat, 1/4 x 1-3/4 x 1/16 inch O-RING - bolt seal SCREW - terminal, special, 5 x 8 mm WASHER - lock, 5 mm WASHER-lock, 10 mm NUT - hex, 10 mm -1.5, field coil terminal WASHER - spring, field coil terminal BUSHING - insulation

REQ'D.

4 1 1 2 3


4-6


4-7

ALTERNATOR REF. 1 2 4 5 6 7 9 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

PART NO. A187873 A187903 :A187906 1964968C1 1530431 CI 3079134R1 1964969C1 A187904 Ai87917 A187899 A187504 1964966C1 A186186 1964964C1 A187901 A186183 3078897R1 NSS NSS NSS NSS NSS A186182 . A186193 221425R1 J908560 J908563

Bur 7-3350

DESCRIPTION REQ'D. ALTERNATOR ASSEMBLY - engine, 65 ampere, electrical . HOUSING - collector ring end REGULATOR - voltage BRUSH - alternator, set of two BOLT - with washer, rectifier bridge retaining CAPACITOR - alternator SCREW - special, Fillister, capacitor retaining SET- hardware, terminal RECTIFIER- alternator SHIELD - alternator BOLT - hex flange, special, voltage regulator retaining STATOR - alternator BEARING - ball, rotor, collector ring end ROTOR - alternator PLATE - bearing retaining BEARING - ball, rotor, drive end KIT - rotor retaining RING - spacer: ; WASHER - rotor shaft. . NUT - rotor shaft KEY - pulley retainer, not used in A187873 alternator SCREW - bearing retaining plate HOUSING - drive end. . . . . BOLT - slotted, special, cover retaining 4 FAN - alternator,"not included with alternator assembly, order separately . . . . . PULLEY - drive, not included with alternator assembly, order separately RETAINER - pulley, not included with alternator assembly, order separately 1


4-8

B9408145S


4-9

STARTER AND ALTERNATOR MOUNTING REF. 1 2 3 4 5 6 7 8

PART NO. 1987559C1 814-10040 J921603 A187873 814-10100 J902469 J903089 : 614-8020

Bur 7-3350

DESCRIPTION STARTER ASSEMBLY - engine, new, parts list pages 4-3 and 4-5 BOLT - hex, 10 - 1.5 x 40 mm BELT - fan, V-ribbed, alternator and fan ALTERNATOR ASSEMBLY - engine, 65 ampere, parts list page 4-7 BOLT-hex, 1 0 - 1 . 5 x 1 0 0 mm SPACER - alternator mounting BRACE - alternator mounting BOLT-hex, full threads, 8-1.25 x 20 mm .

REQ'D. 1 2

2


4-10

TO FRONT CONSOLE HARNESS

COOLANT TEMPERATURE

STARTER SOLENOID

TRANSMISSION CONTROL SOLENOID

FOUR W H E E L DRIVE SOLENOID LH PARKING BRAKE SWITCH FUEL SHUT O F F SOLENOID REAR AXLE TEMP. SWITCH HORN

GOLD START SOLENOID

FUEL L E V E L SENDER TO SIDE CONSOLE HARNESS

POSITION SWITCH

TO AIR SUSPENSION SEAT BACKUP ALARM -LOADER VALVE RETURN-TO-DIG SOLENOID DIFFERENTIAL LOCK SOLENOID RH PARKING BRAKE SWITCH


4-11

ENGINE WIRING HARNESS AND CONNECTIONS REF. 1 1A

PART NO. 282015A3 282016A3

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

A166057 193-1000 1345488C3 515-23127 D143830 493-21033 829-1408 493-21020 824-1405 D147383 D137363 515-23127 D147383 515-23127 844-10020 A166057 193-1000 D39696 829-2410 L71879 192196A2 184188A1

•

24 25 26

49773 844-10025 515-23127

27

814-10060

28 29 30

LI 8337 1983233C1 277016A1

30A 31 32

637-62081 123809A2 123097A1

33 34

D147383 781-24613

Bur 7-3350

DESCRIPTION REQ'D. HARNESS - engine, main, models without air conditioning 1 HARNESS - engine, main, models with air conditioning, not shown, used in production, for service order 282015A3 engine harness above and 186607A1 air conditioning adapter harness on page 4-19 SENDER - engine water coolant temperature NUT - hex, with external tooth lock washer, No. 10 NF SWITCH - coolant temperature CLAMP - P-type, 1/2 inch ID, uses existing engine hardware WIRE - 675 mm long, alternator to starter WASHER - internal tooth lock, 5/16 inch NUT - hex, 8 mm -1.25, class 10 WASHER - internal tooth lock, 3/16 inch. NUT - hex, 5 mm - 0.8 CLAMP - J-type, uses existing engine hardware SWITCH - return-to-dig, see page 9-11 for switch mounting CLAMP - P-type, 1/2 inch ID CLAMP - J-type CLAMP - P-type, 1/2 inch ID BOLT - heavy hex flange, 10 -1.5 x 20 mm . SENDER - transmission temperature NUT - hex, with external tooth lock washer. No. 10 NF CLAMP - P-type, double NUT - hex, flange, 10 mni -1.5, class 10: DIODE - harness, isolation CLAMP - P-type, spring lock WIRE - power, starter to fuseblock, see page 4-21 item 8 for nut at relay block CLAMP - P-type, 1-1/4 inch ID BOLT - heavy hex flange, 10 -1.5 x 25 mm CLAMP - P-type, 1/2 inch ID, see page 7-13, Ref 29 for brake.cable bracket BOLT - hex, 10 -1.5 x 60 mm, see page 7-13, Ref 29 for brake cable support bracket and additional hardware. STRAP - tie, 15 inch, nylon, retaining 27 SWITCH - restriction, air cleaner. SENDER - oil pressure, 10 mm - 1 O-ring thread (part number is stamped on sender) O-RING - 8.1 ID X 1.6 mm wide, 277016A1 sender, not shown. HARNESS - clutch cutout, transmission gear shift lever SWITCH - push-button, clutch cutout, gear shift lever, see page 6-23 for lever and knob CLAMP - J-type, uses,existing loader valve mounting hardware BOLT - hex flange, self-tapping, 6 -1.0 x 13 mm 2


4-12

BS97B264


4-13

B A T T E R Y AND B A T T E R Y C A B L E S IVIODELS WITHOUT COLD START REF. 1 2 3

PART NO. BMF31E 'D83485 844-10020

4 5 6 7 8 9 10 11 12 13 14 15 16

144171A1383619R1 814-10245 D125079 D55561 495-11041 D127018 844-10025 493-11039 895-15008 829-1408 814-8035 257279A1

DESCRIPTION BATTERY - dry, 12 volt, models without cold start STRAP - battery, negative ground BOLT - heavy hex flange, 10 -1.5 X 20 mm, negative battery cable ground bolt to chassis CABLE-positive, 1500 mm long BOOT - positive battery cable BOLT-hex, 10- 1.5x245 mm. BRACKET - battery hold-down . RETAINER - battery WASHER-flat, 13/32x13/16x1/16 inch STRAP - ground BOLT-heavy hex flange, 10 - 1 . 5 x 2 5 mm WASHER - internal-external tooth.lpck, 3/8 inch WASHER - flat, 9 x 20 x 1.6 mm . . . . NUT-hex, 8 mm -1.25, class 10 . . BOLT - hex, 8 - 1.25 x 35 mm GROMMET - battery cable, mounts in chassis side channel

REQ'D. 1 1 1 1 1 2 2 .1 2 2 1 2 1 1 1 2

NOTE: See page 9-79 for battery box.

Bur 7-3350


4-14


4-15

DUAL BATTERY COLD START REF. 1 2 3 4 5 6 7 8 10 11 •

PART NO. BMF28S 184498A1 184497A1 D126409 •73383 181338A1 814-10245 495-11041 250854A1 257279A1

Bur 7-3350

DESCRIPTION BATTERY - dry charged, 12 volt, models with cold start CABLE - positive, 1460 mm long. . CABLE - positive jumper, 227 mm long,. NUT - hex, special, 3/8 inch NC, battery terminal STRAP - ground, flat PLATE - battery mounting BOLT- hex, 10- 1.5x245 mm WASHER - flat, 13/32 x 13/16 x 1/16 inch RETAINER - battery plate, top GROMMET - battery cable, mounts in chassis side channel

REQ'D. .2 1 1 4 2 1 1 •1 1 2


4-16

BS97M208


4-17

FRONT C O N S O L E WIRING HARNESS AND CONNECTIONS REF. 1 2 3 4

PART NO. 282014A2 D147383 781-24820 123538A1

5 6 7. 8

122736A1 13169-1A1 122740A1 278328A1

8

231520A2

8A

236521A1 279520A1 840-1535 D148108 A187990 495-81153

9 10 • 11 12

Bur 7-3350

DESCRIPTION HARNESS - front console CLAMP - J-type, harness to firewall BOLT - hex flange, self-tapping, 8 - 1.25 x 20 mm . . . . SWITCH - rocker, dome lamp, if used, see page 4-23 for plug used in place of switch SWITCH - rocker, hazard, flasher lamps SWITCH - rocker, turn signal SWITCH - rocker, horn ., LEVER - shuttle shift, transmission, forward/neutral/reverse switch, standard transmission LEVER - shuttle.shift, transmission, fonward/neutral/reverse switch, powershift transmission COLLAR - shuttle lever, includes clamp and (2) nuts BOOT - rubber, handle, shuttle shift lever, not s h o w n . . . . SCREW - machine, pan Phillips, 5 - 0.8 x 35 mm SWITCH - rocker, brake lamp TERMINAL - male WASHER - flat, 15/32 x 3/4 x 1/32 inch

REO'D. 1 2 2 1 1 1 1 .1 1 1 1 2 1 2 2


4-18

MAIN H A R N E S S

T O O P T I O N A L RADIO CAB/ROPS LAMPS

IGNITION

POWER PLUGS

COLD START

INSTRUMENT C L U S T E R


4-19

SIDE CONSOLE INSTRUMENT HARNESS REF. 1 2 3 4 4A 5 6 7, 8 9 9A 10 11 12 13 14 15 16 17 18

PART NO. 282013A3 L71879 181378A3 490-1108 490-1106 193-1000 D128310 121412A1 121414A1 121413A1 121416A1 844-6025 832-10406 184277A1 425-106 490-1108 193-1000 281-4556 D147166 D137468

19 20 21 22

D120561 614-10025 829-1410 844-10020

23 24 26 26A

844-6025 832-10406 L I 8337 278665A4 133041A1

27

130876A1

28

186607A1

DESCRIPTION HARNESS - side instrument console, used with Ref 26A relay DIODE - harness, isolation BRACKET - fuse and relay mounting SCREW - machine, pan Phillips, No. 10 NF x 1/2 inch SCREW - machine, pan head Phillips, No. 10 NF x 3/8 inch NUT - hex, with external tooth lock washer, No. 10 NF RELAY - 30 ampere, mini, 12 volt FUSE - mini, 10 ampere, red FUSE - mini, 20 ampere, yellow FUSE - mini, 15 ampere, blue FUSE - mini, 30 ampere,.green BOLT - heavy hex flange, 6 - 1.0 x 25 mm NUT - hex, self-locking, 6 mm - 1 . 0 BLOCK - junction, power NUT - hex, 3/8 inch NC SCREW - machine, pan Phillips, No. 10 NF x 1/2 inch NUT - hex, with external tooth lock washer, No. 10 NF SCREW - self-tapping, hex washer head, No. 10 NC x 3/8 inch SWITCH - flasher, hazard and turn signal ALARM - warning, for engine water temperature, engine oil pressure and parking brake CLAMP - P-type, warning alarm mounting to bracket BOLT - hex, full threads, 10 - 1 . 5 x 25 mm NUT - hex, 10 mm - 1 . 5 , class 10.9 BOLT - heavy hex flange, 10 - 1 . 5 x 20 mm, ground at loader control bracket brace BOLT - heavy hex flange, 6 - 1.0 x 25 mm NUT - hex, self-locking, 6 mm - 1 . 0 S T R A P - t i e , 15 inch RELAY - sealed time delay, shuttle interlock timing relay KIT - harness, field, to install air conditioning on units not presently equipped with air conditioning, order items 27 and 28 HARNESS - adapter, cab, attaches to side console instrument harness for air conditioning connections HARNESS - adpater, engine, attaches to side console instrument harness for air conditioning connections

REQ'D. 1 7 1 4 2 6 13 5 1 3 1 1 1 1 1 2 2 1 1 1 1 1 1 1 2 2 UAR 1

1 • .1 1

*OPTIONAL EQUIPMENT HARNESSES 35 36

*296508A2 *302803A1

HARNESS - side console options HARNESS - chassis options

1 1

* N O T E : Optional equipment consists of ride control, hand held auxiliary hydraulics, auxiliary backhoe hydraulics and hydraulic quick coupler. NOTE: See page 4-21 for additional side console instrument harness and connections.

Bur 7-3350


4-20

AUXIUART uroRAUUCS

@


4-21

SIDE CONSOLE INSTRUMENT HARNESS AND CONNECTIONS REF. 1 2 3 4 5

PART NO. 282013A3 844-6025 893-11006 825-2406 832-10408

6 8

844-8025 425-106

12 13' 14,

133711A1 133713A1 133716A1

15

133715A1 D134737 NSS A773f4 A77313 D137820 " 191532A1

17 18 19 20 21 23 24 25 26 27 28 29 30

-

495-11041 892-11008 829-1408 283779A1 283781A1 187013A1 192299A1 121413A1

Bur 7-3350

DESCRIPTION HARNESS - side instrument console BOLT - heavy hex flange, 6 - 1 . 0 x 25 mm WASHER - external tooth lock, 6 mm NUT - hex flange^ 6 mm - 1 NUT - hex, self-locking, 8 mm - 1 . 2 5 , attaches fuse and relay mounting bracket to parking brake lever mounting bolt BOLT - heavy hex flange, 8 - 1 . 2 5 x 25 mm NUT - hex, 3/8 inch NC, attaches power wire from starter; item 23 on page 4-11, to power junction block . . : SWITCH - rocker, driving lamps SWITCH - rocker, front work lamps SVyiTCH - rocker, four-wheel drive, if used, see page 4-25 for plug used in place of switch SWITCH - rocker, rear flood lamps SWITCH ASSEMBLY - ignition, includes keys SWITCH - key, without keys NUT - hex, special, key switch mounting K E Y - s e t of two,. WIRE - ignition switch to ground SWITCH - rocker, hand held auxiliary hydraulics, if used, see page 4-25 for plug used in place of switch WASHER - flat, 13/32 x 13/16 x 1/16 inch W A S H E R - lock, 8 mm NUT - hex, 8 mm - 1 . 2 5 , class 10 . . . . . . . OUTLET - power plug . . . 7 CAP - power plug outlet. HARNESS - auxiliary hydraulics, hand held DECAL - auxiliary hydraulics FUSE - mini, 15 ampere, auxiliary hydraulics

REQ'D. -1 2 1 2 1 .2 1 1 1 1 1 1 1 1 1 1 .1 2 2 2 2 2 1 1 1


4-22

R O T A T E D 90 FOR C L A R I T Y

Ui

B9501058S

i

I

580 Super L Series 2 Loader Backhoe FRONT INSTRUMENT PANEL AND REF. 1 1A

PART NO. 119266A1 181316A1

2

137851A1

3 4

844-8020 555-2

5 6 7 : 8 9 10 :

833-40406 119267A2 119268A1 140-107 131-623 177164A1

11 12 13 14

140-107 176857A1 126844A1 136450A1

15 16 17 . 18 19 20 21 24

140-107 495-31022 225-14110 136454A1 •126821 151-522 495-31022 D127335

Bur 7-3350

4-23

COVERS

DESCRIPTION REQ'D. PANEL - instrument, front, cab models, item 1A shown 1 PANEL - instrument, front, POPS canopy models, with four bolt holes for anti-vandalism cover 1 PLATE - bar, front console mounting to firewall, not included in cab frame .2 BOLT - heavy hex flange, 8 - 1 . 2 5 x 20 mm 10 BOLT - heavy hex flange, 6 - 1 . 0 x 20 mm, special, instrument panel to firewall 4 NUT-U-type, 6 m m - 1 . 0 4 COVER - upper, steering column 1 COVER - lower, steering c o l u m n . . 1 SCREW - machine, pan head Phillips, No. 10 NC x 3/4 inch 3 NUT - U-type, No. 10 NC. . . . . , 1 BOX - storage compartment (service with 122641 A l box and 120029A1 cover, not shown) 1 SCREW - machine, pan head Phillips, No. 10 NC x 3/4 inch 4 N U T - J - t y p e , No. 10 ,A PLUG - upper, used in place;of dome lamp switch, if used 1 BRACKET - front instrument panel, anti-vandalism, ROPS canopy models .1 SCREW - machine, pan head Phillips, No. 10 NC x 3/4 inch 4 WASHER - flat, 7/32 X 1/2 x 3/64 inch. 4 NUT - hex. No. 10 NC . . . 4 COVER - anti-vandalism, front instrument panel, ROPS canopy models 1 CORD - manual retaining, anti-vandalism cover 1 RIVET - break mandrel, 3/16x 9/16 inch 2 WASHER - flat, 7/32 x 1/2 x 3/64 inch 4 RETAINER - magnetic catch, storage compartment 1


4-24

/15A)

BT97M202


4-25

SIDE INSTRUMENT PANEL AND COVERS REF. 1 2 3 4 5 6 7 7A

PART NO. 245891A2 .555-2 120032A1 182276A1 127009A1 131 -623 295378A1 * 294792A1

8 9 10 11 12 13 14 15 15A 16 17 •18 19

555-2 844-6025 895-15006 832-10406 123615A2 140-1.06 131-619 126844A1 126844A1 353-406 126844A1 126844A1 REF 129586A1

20 21 24 25 30 31

NSS F22426 140-119 181385A1 * 126844A1 * 1340319C1

32 33

*353-429 * 353-401 F42827 *292654A1

DESCRIPTION COVER - loader control BOLT - heavy hex flange, 6 - 1 . 0 X 20 mm . PANEL - fuse access S C R E W - special, No. 1 0 N C x 3 / 4 i n c h RETAINER - screw, push-on NUT - U-type, No. 10 NC PANEL - instrument, side, models without.radio, if used, also order (1) 181385A1 threaded insert PANEL - instrument, side, models with radio, if used, also order (1) 181385A1 threaded insert, not shown. BOLT - heavy hex flange, 6 - 1.0 x 20 mm BOLT - heavy hex flange, 6 - 1.0 x 25 mm WASHER - flat, 6.6 x 25 x 1.6 mm NUT - hex, self-locking, 6 mm - 1 . 0 PANEL - instrument cluster mounting SCREW - machine, pan head Phillips, No. 10 NC x 1/2 inch NUT : J-type, No. 10 NC . . . . . PLUG - auxiliary hydraulics, if used. PLUG - accessory option, if used PLUG - button, 5/8 inch, nylon, used in place of cold start button, if used PLUG - used in place of differential lock switch, if used \. PLUG - used in place of four-wheel drive switch, if used DECAL - fuses and relays, see page 9-155, Ref 4 for decal COVER ASSEMBLY - instrument cluster panel, anti-vandalism, uses existing hardware, ROPS canopy models COVER - instrument cluster panel BUMPER - rubber SCREW - machine, pan head Phillips, No. 10;NC x 1-1/4 inch INSERT-threaded, 8 m m - 1 . 2 5 , ifused PLUG - ride control; if used , PLUG - flat face, pry out, 7/16 inch diameter, if used, replaces 353-425 -plug PLUG - flat face, pry out, 11/16 inch diameter PLUG - button, 5/16 inch TRIM - edge, bulk, 2946 mm (116 inch) long

REQ'D. 1 3 1 2 2 1 1 .1 3 1 1 1 1 .8 8 1 1 1 1 1 1 1 1 3 4 .1 .5 1 1 2 1

KIT - radio-ready package, includes above items marked with an asterisk, plus see parts on pages 4-45 and 9-133.

• •1 .-

NOTE: See page 4-21 for side console switches.

Bur 7-3350


4-26

@

6

B902634S

580 Super L Series 2 Loader Baclchoe

4-27

INSTRUMENT CLUSTER REF.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

PART NO. A187965 A191114 N13545 H422774 H422758 H422766 A45007 N13543 N13542 A47688 N6807 N13546 D146335 D71342 D71343 D71344 A45093 D71346 W10478 A47123 A47125 225-14106 N14225 140-107

Bur 7-3350

DESCRIPTION CLUSTER ASSEMBLY - instrument, tractor HOUSING ASSEMBLY - instrument cluster HOUSING - instrument cluster BOARD - circuit, printed, instrument cluster GASKET - housing CLIP - gauges COVER - instrument cluster GAUGE tachometer, includes hourmeter GAUGE water temperature GAUGE fuel level GAUGE voltmeter GAUGE oil temperature LENS - identification, warning lamps GASKET - lens GASKET - instrument cluster BOOT - rubber, lamp socket SCREW - special B U L B - l a m p , No. 168 BULB - lamp, No. 194 SOCKET-lamp SOCKET - lamp, green N U T - h e x . No. 6 N C SHIELD - instrument cluster SCREW - machine, pan head Phillips, No. 10 NC x 3/4 inch

REQ'D.

.1

2 3 8 3 8 3 3 "I 4


4-28

BS97M205


4-29

TRACTOR LAMP ELECTRICAL CIRCUIT

WITH ROPS CANOPY REF. 1

PART NO. D132681

2

D132682

3 4 5

493-11052 425-148 D135384

6 7 8 9

D121152 281^4556 495-31022 283001 A l

DESCRIPTION REQ'D. LAMP ASSEMBLY - front driving, outer, parts list page 4-33, no longer available, order ZAA7376350 lamp package 2 LAMP ASSEMBLY - flood and work, rear flood (outer) and center front and rear work lamps, parts list page 4-33, no longer available, order ZAA7376150 lamp package and ZAA8066600 mounting kit 6 WASHER - internal-external tooth lock, 1/2 inch 8 NUT - hex, jam, 1/2 inch NC 8 LAMP ASSEMBLY - turn signal and flasher, amber, front and rear, parts list page 4-37. 4 LAMP ASSEMBLY - stop and tail, red, rear, parts list page 4-37 2 SCREW - self-tapping, hex washer head. No. 10 NC x 3/8 inch .12 WASHER - flat,'7/32 x 1/2 x 3/64 inch. . 12 HARNESS - ROPS canopy, lamps, attaches to side console instrument harness, see page 9-147 for harness cover and clamps that mount to the right-hand ROPS post 1

NOTE: See side console harness page 4-19 for lamp fuses and page 4-21 for lamp switches.

Bur 7-3350


4-30

/


4-31

TRACTOR LAMP ELECTRICAL CIRCUIT

WITH CAB REF. • 1

PART NO. 282017A2

1A

282018A2

2 3

109080A1 109081A1

4 6

409-768 187834A1

7

187836A1

8 9 ^ 10 11 12 13 13A 14

814-8035 892-11008 495-81001 186756A1 183598A2 495-21056 181385A1 131797A1

15

131796A1

16

183504A1

17

131795A1

18

183505A1

19

131794A1

20 21 22 23 24

190-105 181459A1 L18337 L60224 1202956C1

DESCRIPTION REQ'D. HARNESS - cab, models without air conditioning, attaches to side console instrument harness 1 HARNESS - cab, models with air conditioning, not shown, attaches to side console instrument harness, used in production, for service order 282017A2 cab harness (item 1) and 130876A1 adapter harness, item 27 on page 4-19 1 LAMP ASSEMBLY - front driving, parts list page 4-37 2 LAMP ASSEMBLY - flood and work, rear flood and front and rear work lamps, parts list page 4-37 :6 BOLT - hex serrated flange, 3/8 NC x 1/2 inch 8 BRACKET - left-hand lamp, includes inserts, (4) Ref 13A and (6) Ref 2 1 , cab models ..., 1 BRACKET - right-hand lamp, includes inserts, (4) Ref 13A and (6) Ref 2 1 , cab models : 1 BOLT - hex, 8 - 1.25 x 35 mm, laihip bracket t o cab frame : 8 WASHER - lock, 8 mm .8 WASHER - flat, 3/8 x 1-1/8 x 1/16 inch 8 WASHER - Belleville 8 SPACER - cab lamp bracket mounting 1 8 WASHER - flat, 9/16 x 1-3/8 x 7/64 inch 8 INSERT - threaded, 8 mm - 1 . 2 5 . . . .8 LAMP ASSEMBLY - turn signal and flasher, amber lens, left-front, parts list page 4-43 LAMP ASSEMBLY - turn signal and flasher, amber lens, right front, parts list page 4-43 LAMP ASSEMBLY - turn signal and flasher, amber lens, left rear, upper, parts list page 4-43 LAMP ASSEMBLY - stop and tail, red lens, left rear, lower, parts list page 4-43 LAMP ASSEMBLY - turn signal and flasher, amber lens, right rear, upper, not shown, parts list page 4-43 LAMP ASSEMBLY - stop and tail, red lens, right rear, lower, not shown, parts list page 4-43 SCREW - machine, pan Phillips, No. 10 NF x 1-3/4 inch, lamp to bracket 12 INSERT - No. 10 NF .12 STRAP - tie, 15 inch, nylon, retaining . .7 BUMPER - rubber .2 CONDUIT - convoluted insulation, 16 (5/8) x 2 1 (53/64) x 889 mm (35 inch) long, windshield 1

NOTE: See side console harness-page 4-19 for lamp fuses and page 4-21 for lamp switches.

Bur 7-3350


4-32


4-33

CANOPY TRACTOR LAMPS

FRONT DRIVING, REAR FLOOD, AND FRONT AND REAR W6RK LAMPS REF.

PART NO.

REQ'D.

DESCRIPTION

FRONT DRIVING LAMP ASSEMBLY D132681 1 2 3 4 5

NSS 91946C1 273-10510 N14284 70-12532

5A 6 . 6A 6B

413-432 231-1444 492-11050 425-108

LAMP ASSEMBLY - front driving, no longer available, order ZAA7376350 lamp package HOUSING - lamp . . . ; BULB - sealed beam SCREW - self-tapping, flat head slotted. No. 10-16 x 5/8 inch BRACKET - lartip SCREW - machine, pan head slotted, 1/4 NC X 2 inch, housing to bracket, production BOLT - hex, 1/4 NC x 2 inch, service NUT - hex, self-locking, 1/4 inch NC . WASHER - lock, 1/2 inch . . . N U T - h e x , 1/2 inch NC

-2 1^ 1 2 1 1 . . .1 = .1 . 1 -1

REAR FLOOD LAMP ASSEMBLY AND FRONT AND REAR WORK LAMPS D132682

7 8 9 10

NSS 91947C1 273-10510 70-12532

10A 11 12 13 14

413-432 231-1444 N14285 A52216 121-119

14A 15 16

413-536 65881H, 231-1445

Bur 7-3350

LAMP ASSEMBLY - flood and work, rear flood (outer) and center front and rear work lamps, no longer available, order ZAA7376150 lamp package and ZAA8066600 mounting kit package HOUSING-lamp . BULB - sealed beam SCREW - selfrtapping, flat head slotted. No. 10-16 x 5/8 i n c h . . ; SCREW - machine, pan head slotted, 1/4 NC X 2 inch, housing to bracket, production. BOLT - hex, 1/4.NC x 2 inch, service NUT - hex, self-locking, 1/4 inch NC •. B R A C K E T - lamp, mounting BRACKET - mounting, lamp, includes stud BOLT - hex serrated flange, 5/16 NG x 2-1/4 inch, black, special, used in production, for service order item 1 4 A . . . . . .-^ BOLT - hex, 5/16 NC x 2-1/4 inch, service SPACER - tubular, 1/4 x 1-1/4 inch NUT - hex, self-locking, 5/16 inch NC

6 1 1 2 1 .1 1 1 .1 1 .1 1 .1


4-34

B922656S


4-35

C A B TRACTOR LAMPS FRONT DRIVING, REAR FLOOD, AND FRONT AND REAR WORK LAMPS REF.

PART NO 109080A1 109081A1

1 2 2A 3 4 5 6

NSS A187912 A187911 273-5048 A187914 413-432 231-5144

Bur 7-3350

DESCRIPTION LAMP ASSEMBLY - front driving LAMP ASSEMBLY - flood and work, rear flood and front and rear work lamps HOUSING-lamp L A M P - s e a l e d ' b e a m , 109080A1 lamp LAMP - sealed beam, 109081A1 lamp. SCREW - self-tapping, flat head slotted, No. 8-18 x 1/2 inch BRACKET - mounting, lamp BOLT - hex, 1/4 NC x 2 inch NUT - hex serrated flange, 1 /4 inch NC

REQ'D. . . . .2 6 1 1 .1 2 1 1 1


4-36

870040S


4-37

CANOPY TRACTOR LAMPS STOP AND TAIL LAMPS AND TURN SIGNAL AND FLASHER LAMPS REF.

PART NO.

REO'D.

DESCRIPTION

STOP AND TAIL LAMP 1 2 3 4

D121152 NSS T34857 N6836 261-14310

LAMP ASSEMBLY - stop and tail, red BODY - lamp, complete BULB - lamp. No. 1157, stop and tall LENS - red, lamp SCREW - self-tapping, pan Phillips, No. 6 NC X 5/8 inch

• • -2 1 1 1 2

TURN SIGNAL AND FLASHER 5 6 7 8 ' 9 10 11

D135384 NSS NSS NSS NSS A41264 N14283 261-14310

Bur 7-3350

LAMP ASSEMBLY - turn signal and.flasher, amber BODY AND SOCKET - lamp SEAL - rubber, spring retaining SPRING - lamp. . INSULATOR- lamp BULB - lamp, 12 volt. No. 1156, turn signal and flasher LENS - amber, lamp SCREW - self-tapping, pan Phillips, No. 6 NC x 5/8 inch


4-38


4-39

C A B TRACTOR LAMPS STOP AND TAIL LAMPS AND TURN SIGNAL AND FLASHER LAMPS REF.

PART NO.

DESCRIPTION

REQ'D.

STOP AND TAIL LAMP

1 2 3

131794A1 131795A1 NSS T34857 183749A1

LAMP ASSEMBLY - stop and tail, red-lens, right rear,-lower LAMP ASSEMBLY - stop and tail, red lens, left rear, lower^. BODY - lamp, complete BULB - lamp, No. 1157, stop and tail LENS - lamp, red

TURN SIGNAL AND FLASHER i

4 4A 5 6

131796A1 183505A1 131797A1 183504A1 NSS NSS A41264 183748A1

Bur 7-3350

'

' •'

LAMP ASSEMBLY - turn signal and flasher, amber lens, right front LAMP ASSEMBLY - turn signal and flasher, amber lens, right rear, upper. LAMP ASSEMBLY - turn signal an'd flasher, amber lens, left front LAMP ASSEMBLY - turn signal and flasher, amber lens, left rear, upper. . B O D Y - 131796A1 or131797A1 lamp BODY - 183504A1 or 183505A1 lamp BULB - lamp, 12 volt. No. 1156, turn signal and flasher LENS - lamp, amber


4-40

BT97N118


4-41

HORN AND B A C K U P ALARM REF.

PART NO.

DESCRIPTION

REQ'D.

HORN 1 2 3 4 5 6 7

-

190155A1 116423A1 893-11008 814-8110 L I 8337 895-11008 829-1408

" HORN - 1 2 volt, includes mounting bracket SPACER - split WASHER - external tooth lock, 8 mm BOLT - hex, 8 - 1 . 2 5 x 110 mm S T R A P - t i e , 15 inch WASHER - flat, 9 x 1 7 x 1 . 6 mm, if used NUT - hex, 8 mm - 1 . 2 5 , class 10, if used

.

1 1 1 1 2 1 :2

BACKUP ALARM 8

109511A1

9 10 11 12

614-8025 895-11008 832-10408 D139175

ALARM - backup, attaches to main engine harness, see page 4-11 for engine harness options BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER-flat, 9 x 1 7 x 1 . 6 m m NUT - hex, self-locking, 8 mm - 1 . 2 5 ' WIRE - pigtail, attaches main engine harnessto alarm.

1 2 2 2 1

NOTE: See front console instrument harness page 4-17 for horn switch.

Bur 7-3350


4-42

B9408269T

580 Super L Series 2 Loader Backhoe ROTATING B E A C O N USED ON CAB OR CANOPY MODELS REF. 1 2 3 4 5 6 7 8 9 ••*• 10 11 12 13 14

PART NO. A23870 493-11026 495-21031 108366A1, A187542 127158A1 168-71 238-5005 - 101531A1 3125705R1 A1875t5 NSS 614-6020 136-54

4-43

DESCRIPTION GROMMET-wire WASHER - internal-external tooth lock, 1/4 inch, ground W A S H E R - f l a t , 5 / 1 6 x 3 / 4 x 1 / 1 6 inch, ground BEACON ASSEMBLY - rotating, attaches to cab or canopy harness LENS - beacon, amber, if used LENS - beacon, blue, if used SCREW - drive, round head. No. 8 x 1/2 inch, lens mounting O-RING - 3/32 ID x 1/16 inch wide, lens mounting screw CLIP-.bulb.L A M P - beacon, 12 volt, 55 watt BELT - drive motor, rotating beacon . . . BASE - with drive motor BOLT - hex, full threads, 6 - 1 . 0 x 20 mm PIN - cotter, hair, 1/4 x 11/16 inch, bolt retaining

REQ'D. 1 1i 1 1 1 1 3 3 1i t 1 1 3 3

NOTE: See side console instrument harness page 4-21 for beacon switch and page 4-19 for fuse.

Bur 7-3350


4-44

1

4J[

BT97K168


4-45

*RADIO, MOUNTING BOX, ANTENNA AND S P E A K E R S REF.

1 2 3 4 5 6 7 " 8 9 10 11

PART NO. *292654A1 221418A1 161-115 ' 495-11028 231-1444 300157A1 i82721A2 187281A1 .. 7 6 1 - 1 7 3 2 5 177269A1 298228A1 197745A1

12 13

284549A1 291010A1

14 15

760-14413 893-11005

DESCRIPTION REO'D. KIT - radio-ready package, also includes right-hand side instrument panel, see page 4-25 1 BOX - radio mounting 1 SCREW - hex socket button head, 1/4 NC x 3/4 inch 2 WASHER - flat, 9/32 x 5/8 x 1/16 inch 2 NUT - hex, self-locking, 1/4 inch NC 2 HEADLINER ASSEMBLY - cab, models with radio-ready package, see page 9-133 for headliner components. 1 SPEAKER - radio, 5-1/4 inch, round 2 GRILLE - speaker cover . .2 SCREW - self-tapping, pan Phillips, 4.2 - 1 . 4 x 25 mm 8 NUT - U-type, spring 8 HARNESS-speaker 1 ANTENNA - radio, includes flat washer and nut which are not serviced separately ., . -1 CABLE - antenna 1 WIRE - antenna ground, ground eyelet must be mounted on cab side of antenna cable or am radio will not operate 1 SCREW - self-tapping, pan Phillips, 4.8 - 1 . 8 x 13 mm .1 WASHER - external tooth lock, 5 mm 1

* N O T E : Does not include radio. For headliner used on models with the radio-ready kit, see page 9-133.

Bur 7-3350


4-46

TO

BACKHOE

AUXILIARY CONTROL

VALVE


4-47

BACKHOE AUXILIARY HYDRAULIC E L E C T R I C A L CIRCUIT REF. 1 . ' 2 . 3 4 5

PART NO. 121.4,13A1 284479A1 284058A1 284627A1 296508A2

6 7 8 9 10 11 12 13 14 15 16 17

L18337 302803A1 298681A1 D137363 440-10616 895-11004 193-1003 137219A1 300030A1 843-1516 892-11005 824-1405

DESCRIPTION REQ'D. FUSE - mini, 15 ampere 1 DECAL - backhoe auxiliary hydraulics, hi flow/low flow. . . : .1 SWITCH - rocker.'^backhoe auxiliary hydraulics, mounts below key s w i t c h . . . . . .1 DECAL - backhoe auxiliary hydraulics, low flow - light on/hi flow - light off 1 HARNESS - side console options, attaches to side console harness and chassis options harness 1 S T R A P - t i e , 15 inch 4 HARNESS - chassis options 1 HARNESS - pigtail, detent lever .,. 1 SWITCH - contact, limit 1 SCREW - machine, pan Phillips, No. 6 NC x 1 inch 2 WASHER - flat, 4.4 x 9 x 0.8 mm 2 NUT - hex, with external tooth lock washer, No. 6 NC 2 SWITCH - foot, backhoe auxiliary hydraulics 1 GUARD - foot switch 1 S C R E W - m a c h i n e , flat Phillips, 5 - 0 . 8 x 1 6 mm ..2 WASHER - lock, 5 mm . . . . .2 NUT-hex, 5 m m - 0 . 8 . 2

NOTE: See pages 8-51 - 8-55 for backhoe auxiliary hydraulics, page 9-43jfor auxiliary control lever and page 9-25 for the backhoe control tower cover used with auxiliary hydraulics.

Bur 7-3350



5-1

A L P H A B E T I C A L INDEX STEERING DESCRIPTION Axle and Spindles Column - Steering Cylinder - Two Wheel Drive Hub and Bearings Hydraulic Circuit Valve - Steering Control Wheel - Steering Wheels and Tires

Bur 7-3350

PAGE 5-15 5-9 5-13 5-17 5-5,5-7 5-11 5-3 5-19


5-2

BS97M216


5-3

STEERING WHEEL AND STEERING COLUMN REF. 1 2 3 4 5 6 7 8 9 10 11

PART NO. 1342054C1 114882A1 238-5227 1959509C1 A65544 142930A1 614-10020 614-10030 183085A2 614-8020 829-1408

DESCRIPTION INSERT - plastic, black . . . . CAP - steering wheel. 0-RING - 2-1/8 ID x 1/8 inch wide, cap NUT - lock, special, steering wheel retaining WHEEL - steering, tractor COLUMN ASSEMBLY - steering, parts list page 5-9 BOLT - hex, full threads, 10 -1.5 x 20 mnn BOLT - hex, full threads, 10 -1.5 x 30 mnri PLATE - mounting, steering column BOLT - hex; full threads, 8 - 1.25 x 20 mm . . NUT-hex, 8 mm - 1.25, class 10

REQ'D.

2 . . .2 1 4 -4

NOTE: .See page .4-17 for turn signal rocker switch.

Bur 7-3350


5-4

BT97N119


5-5

STEERING HYDRAULIC CIRCUIT REF. 1

PART NO. REF

2 3 4

282428A1 237-6006 218-5576

5 6

237-6010 144221A1

7 8 9

218-5053 237-6004 224423A1

10 11 12

218-5059 237-6008 132929A1

13 14 15 -

120386A1 120388A1 144219A1

17

G107720

18 19 20

122536A1 218-5280 237-6008

DESCRIPTION VALVE ASSEMBLY - loader control, for correct assembly and components, see page 8-73 or 8-75 VALVE - steering check, models with hand held auxiliary hydraulics 0-RING -15/32 ID x 5/64 inch wide TEE - 3/4-16 fl branch x 1-1/16-12 fl x 7/8-14 inch adj 0-ring, lower inlet port, for 45 degree elbow used with this tee on models with ride control, see page 8-61 0-RING - 3/4 ID X 3/32 inch wide, 218-5241 or 218-5576 tee HOSE - 1275 mm (50-3/16 inch) long, steering pilot, steering control valve small center port to loader contt-ol valve. ADAPTER - straight, 7/16-20 flare x 0-ring boss . 6-RING - 23/64 ID x 5/64 inch wide. HOSE - 1300 mm (51-3/16 inch) long, steering pressure, loader control valve to steering control valve right-hand port. . . ; ADAPTER - straight, 3/4-16 inch flare x 0-ring boss 0-RING - 41/64 ID x 3/32 inch wide HOSE - 730 mm (28-3/4 inch) long, steering control valve upper and lower left-hand ports to tubes TUBE - lower, to steering cylinder right-hand port hose TUBE - upper, to steering cylinder left-hand port hose . . . i , HOSE - 485 mm (19-3/32 inch) long, to right-hand and left-hand port of steering cylinder CYLINDER ASSEMBLY - 70 (2-3/4) ID x 170 mm (6-45/64 inch) stroke, steering, parts list page 5-13 FILTER ASSEMBLY - hydraulic oil, parts list page 8-145 ELBOW - 90 degree, 3/4-16 flare" x 9/16-18 inch adj O-ring boss 0-RING - 41/64 ID x 3/32 inch wide

REQ'D. 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 1


Bur 7-3350


5-6

(13)

BT97N119


5-7

STEERING HYDRAULIC CIRCUIT REF. 21

PART NO. 176328A1

22

LI 8337

23 25 26 27

120421A2 D40236 614-10030 218-5136

28 29 30 31 32 35

237-6008 515r23190 515-22127 515-23159 LI 8337 218-5057

36 39 40 41 42

237-6006 D132982 191704A1 LI 8337 49773

Bur 7-3350

DESCRIPTION REQ'D. HOSE - 1730 mm (68-1/8 inch) long, steering return, steering control valve upper right-hand port to hydraulic oil filter 1 STRAP - tie, 15 inch, nylon, retaining, use (1) to tie return hose, item 21, to corner of crossover tube, item 2, shown on page 7-9, use (1) to tie pilot hose, item 6, and pressure hose, item 9, together 5 VALVE ASSEMBLY - steering control, parts list page 5-11 1 CLAMP-tube 2 BOLT-hex, full threads, 1 0 - 1 . 5 x 3 0 mm . . 2 ELBOW - 45 degree, 3/4-16 inch flare x adj O-ring boss, see page 6-3 for fittings used on four-wheel drive front axle 2 O-RING - 41/64 ID x 3/32 inch"wide 1 CLAMP - P-type, 3/4 inch ID 1 CLAMP - P-type, 1/2 inch ID, replaces 49854 clamp . 1 CLAMP - P-type, 5/8 inch ID, if used 1 STRAP - tie, 15 inch, if used 1 ADAPTER - straight, 9/16-18 inch flare x 0-ring boss, may be used on models without auxiliary hydraulics, if used ' 1 . O-RlNG -15/32 ID x 5/64 inch wide. 1 SLEEVE - hose guard 2 SLEEVE - hose guard, 460 mm (18-1/8 inch) long 1 STRAP-tie, 15 inch 2 CLAMP-P-type ' 1


5-8

B9408139S


5-9

STEERING COLUMN REF. 1 2 3 4, 5 6 7

PART NO. 142930A1 NSS S115351 NSS 102-1387 L30881 NSS 614-10020

Bur 7-3350

DESCRIPTION COLUMN ASSEMBLY - steering COLUMN - steering shaft CAP-shaft RETAINER - bearing RING - external spiral retaining, No. 87, bearing BEARING - roller, steering shaft FLANGE-tube BOLT - hex, full threads, 10 -1.5 x 20 mm . . :

REQ'D. 1 1 1 1 .1 1 1 2


5-10

ROTATED 180* F O R PART IDENTIFICATION

ROTATED 180' FOR PART IDENTIFICATION

BS97B271


5-11

STEERING CONTROL VALVE REF. 1 2 3 4 5 6 8 9 10 11 12 13 14 15 16 •17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

PART NO. 120421A2 #NSS NSS NSS N14250 L30889 NSS L30888 211-1006 136494A1 - ^ N14763 . 143717A1 135867A1 , 143723A1 143721A1 NSS NSS L30878 135869A1 *.238-5040 L35368 211-1010 * L3d893 D82806 * 238-5012 D82805 G13609 D82804 S110170 * 238-5225 *NSS *697494R91 S110169 NSS 196087A1 * 1343658C3

DESCRIPTION VALVE ASSEMBLY - steering control HOUSING - control valve SLEEVE - control valve SPOOL - control valve KIT - centering spring SPRING - spool, centering, 6 in kit, order N14250 kit. SPACER - spring PIN - roll, centering BALL - chrome alloy steel, 3/16 inch, grade 24, anticavitation •RETAINER - spring, anticavitation -SPRING - anticavitation BOLT -12 point flange, special, 5/16 NC x 2 inch CAP - end; without O-ring groove SPACER - gerotor, drive shaft GEROTOR - pump, control valve ROTOR - control valve .'. STATOR - control valve SHAFT - drive, gerotor, steering control valve PLATE - spacer, with.O-ring groove O-RING - 2-7/8 ID x 1/16 inch wide, cover and housing RETAINER - check ball BALL - chrome alloy steel, 5/16 inch, grade 24, check O-RING - 7/16 inch ID, seat, inner SEAT-ball, check O-RING - 3/8 ID X 1/16 inch wide, seat, outer. SCREW - set, hex socket, special BEARING - needle; spool RACE - thrust, bearing, bearing GLAND - seal, spool, seal O-RING -1-7/8 ID X 1/8 inch wide, seal retainer SEAL - spool, inner SEAL - 1 inch ID, spool, outer RING - retaining, seal VALVE ASSEMBLY - relief, factory preset, do not remove SPRING - detent, check ball . . . ; KIT - seal, low torque, includes above items marked with an asterisk

REQ'D.

4 2 • • -I .2 2 2 7

3

2 1-

#NOTE: Housing may have a 5/16 - 24 inch hole tapped next to the center hole (steering pilot pressure). The 5/16 inch hole has a Parker Hannifin fitting #2 hp50n-2 installed in it. This is a hollow hex straight thread O-ring plug. The plug must be purchased from Parker Hannifin with the O-ring or use 218-5205 plug with 237-6002 O-ring.

Bur 7-3350


5-12

0

0

861748S

0


5-13

STEERING CYLINDER *TWO W H E E L DRIVE FRONT A X L E REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

G106808 129-369 G106832 425-106 0106817 0106810 **D95142 **0107921 * * 238-5230 * * 032129 0107721 NSS NSS **0105187 * * 0104439 * * 0104454 . 425-1514 0106813

DESCRIPTION CYLINDER ASSEMBLY - 70 (2-3/4) ID x 170 mm (6-45/64 inch) stroke, see footnote, steering, two wheel drive front axle . TUBE - cylinder NUT - hex, jam, left-hand thread, 7/8 inch NF EYE - rod, left-hand thread NUT - hex, 3/8 inch NO ROD - tie, 338 mm (13-5/16 inch) long, cylinder OLAND - cylinder WIPER - piston rod, outer SEAL - U-cup, piston rod, wide, with 0-ring 0-RINO - 2-1/2 ID X 1/8 inch wide, gland RING - backup, gland O-ring ROD ASSEMBLY - piston, 38 mm (1-1/2 inch) diameter ROD - piston . . PISTON - cylinder RING - wear, piston : RING - seal, inner SEAL - piston, expandable, outer. NUT - hex, jam, 7/8 inch NF EYE - rod, right-hand thread

>** 0110045

KIT - seal, includes all items with an asterisk

PART NO. 0107720

REQ'D.

NOTE:' The cylinder assembly part number is stamped on some cylinder glands or tubes. * NOTE: See page 6-9 for the four-wheel drive front axle steering cylinder.

Bur 7-3350


5-14

5 ®

©

®

B9408130S

(31)—


5-15

FRONT AXLE AND SPINDLES TWO W H E E L DRIVE M O D E L S REF. 1 2 3 4 5 6 7 8 9 10 11

PART NO. D138954 D137345 D138047 800-44050 191796A1 D123684 D123655 138616A1 219-1 .800-44050 G107720

12 13 14 15

218-5136 237-6008 13-1638 D36505

16 D123806 17 > D125340 18 D125341 19 . D127507 20 D150155 21 219-89 22 413-632 23 492-11038 24 425-106 25 * D57486 26 492-11050 27 425-118 28 *A27602 29 *D123865 30 * 219-89 31 * 100-21237 32 * D72371 33 * 238-5139 34 *A28230 35 * D72372 36 *D61297 37 495-11094 38 103-1687 *D103626

Bur 7-3350

DESCRIPTION REQ'D. AXLE ASSEMBLY - front, with single rear bushing 1 BUSHING - axle, front 1 BUSHING - 54 mm (2-1/8 inch) long, axle, rear 1 RING - external retaining, No. 50, axle pivot pin retaining, front : .1 WASHER - fiat, special, used as spacer UAR WASHER - thrust, 2-1/16 x 4-1/2 x 3/16 inch, front 1 SEAL - grease 2 PIN - axle pivot 1 FITTING - grease, straight, 1/8 PT x 21/32 inch .2 RING - external retaining, No. 50, axle pivot pin retaining, rear 1 CYLINDER ASSEMBLY - 70 (2-3/4) ID x 170 mm (6-45/64 inch) stroke, two wheel drive front axle, parts list page 5-13 1 ELBOW - 45 degree, 3/4-16 inch flare x adj 0-ring boss 2 0-RING - 41/64 ID x 3/32 inch wide 1 BOLT - hex, 1 NC x 2-3/8 inch 2 WASHER - flat, special, 1-1/16 x 1-7/8 x 9/64 inch, 1-1/16 x 1-7/8 x 9/64 inch, hardened 2 LINK^keering -2 SPINDLE ASSEMBLY - right-hand 1 SPINDLE ASSEMBLY - left-hand, not shown 1i BUSHING - spindle, used on D125340 or D125341 spindle 1 "PIN - steering link 4 FITTING - grease, 45 degree, 1/8 PT self-tap x 25/32 inch 4 BOLT - hex, 3/8 NC x 2 inch 8 WASHER - lock, 3/8 inch 8 NUT - hex, 3/8 inch NC 8 PIN - kingpin lock 2 WASHER-lock, 1/2 inch 2 NUT-hex, 1/2 inch NF 2 BEARING - roller, steering knuckle, spindle 2 KINGPIN - front axle 2 FITTING - grease, 45 degree, 1/8 PT self-tap x 25/32 inch. .4 RING - internal retaining, No. 237, bearing retaining 4 SPACER - kingpin . 4 O-RING - 2-3/16 ID-x 3/32 inch wide, kingpin seal 4 BEARING - needle, kingpin . -. 4 WASHER - thrust, bearing. 2 SEAL-oil. . . . 2 WASHER - flat, 15/16 x 1-3/4 x 1/8 inch 8 RING --heavy exterrial retaining. No. 87, pin 8 KIT - kingpin, includes items marked with an asterisk, quantity in kit services one side of axle

1


5-16

850390S


5-17

FRONT WHEEL HUB AND BEARINGS REF. 1 2

PART NO. D75103 A66759 *619387R1

3

*625743C1

4 5 6 7 8 9 10 11 12

D143405 A38208 432-1232 425-1918 D74949 *G15215 :*A61449 *A61448 *A61447 * B93222

Bur 7-3350

DESCRIPTION HUB ASSEMBLY - front wheel, order items 1-3 HUB-front wheel CUP - tapered roller bearing, 3-1/16 inch OD, outer, tapered roller bearing CUP - tapered roller bearing, 3-35/64 inch OD, inner, tapered roller bearing CAP-hub . . BOLT - wheel retaining PIN - cotter, 3/16x2 inch NUT - hex, thick slotted, 1-1/8 inch NF . . WASHER - flat, special,-1-1/8 inch BEARING - tapered roller, outer SEAL-spindle SEAL-hub CONE - tapered roller bearing, 2-1/16 inch ID, inner KIT - wheel bearing, includes above items marked with an asterisk, two kits required per tractor

REQ'D. 2 1 1 1 2 16 2 .2 2 2 2 2 2 1


5-18

if

B902735S


5-19

FRONT W H E E L S AND T I R E S REF.

PART NO.

DESCRIPTION

REQ'D.

FOR 11L X 16 -10 PR F3 TIRES TWO WHEEL DRIVE MODELS 1 2 3

D125223 REF A38261

WHEEL-rim TIRE - front, purchase locally VALVE - stem, tire inflation

2 2 2

FOR 12x16.5- 8 PR TIRES FOUR WHEEL DRIVE MODELS 4 5 6

119243A1 REF A38261

WHEEL-rim, 8-hole pattern . . TIRE - front, purchase locally VALVE - stem, tire inflation .

2 2 2

WHEELBOLTS TWO WHEEL DRIVE MODELS 7

A38208

BOLT - wheel retaining

16

WHEEL NUTS FOUR WHEEL DRIVE MODELS 8 9

825-11418 496-81000

Bur 7-3350

NUT-hex, 18 mm - 1.5, special WASHER-flat, 25/32 X 1-3/8x 1/8 inch, hardened

16 16i



6-1

A L P H A B E T I C A L INDEX POWER TRAIN DESCRIPTION Axle - Front Four-Wheel Drive Axle Housing Axle Shafts Cylinder - Steering Differential Drive Shaft - to Transmission Mounting Planetary Ring and Pinion Gear Set Swivel Housing Axle - Rear Drive Differential Differential Lock Drive Shaft - to Transmission Housing Mounting.. Planetary Ring and Pinion Gear Set Cooling System Drive Shaft - Front Drive Axle to Transmission Drive shaft - Rear Drive Axle to Transmission Transrnission Dipstick Filter-Oil Housing Idler and Primary Shaft input Shaft Mounting OutputShaft Pump - Oil Secondary Shaft Shift Lever Shifter Mechanism Valve - Control Valve - Solenoid Wheels and Tires - Rear

Bur 7-3350

PAGE 6-5 6-11 6-9 6-15 .6-19 6-3 6-13 6-17 6-7

;

,

6-61 6-57,6-65 6-69 .6-59 6-55 6-67 6-63 .....6-21 6-19 6-69 6-23 6-27 6-29,6-31 6-39 6-41 6-23 6-47 6-33 6-43,6-45 6-23 6-35,6-37 6-49 6-51 6-53


6-2

BT97M218


6-3

FRONT DRIVE A X L E MOUNTING AND DRIVE SHAFT REF. 1 2 3 4 4A 5 5A 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

PART NO. 113561A1 825-11418 496-81000 * 218-5351 237-6006 * 218-5280 237-6006 219-1 800-44050 191796A1 138616A1 D123684 284713A1 608-12025 137223A2 827-12045 495-21056 90-6682T1 D137627 282038A1 282033A1 495-21056 827-12045 829-1412

DESCRIPTION AXLE ASSEMBLY - front drive, parts list pages 6-5 - 6-17 NUT-hex, 18 mm-1.5 WASHER - flat, 25/32 x 1-3/8 x 1/8 inch, hardened ADAPTER - straight, 3/4-16 flare x 9/16-18 inch 0-ring boss 0-RING - 15/32 ID x 5/64 inch wide ELBOW - 90 degree, 3/4-16 flare x 9/16-18 inch adj 0-ring boss 0-RING.- 15/32 ID-x 5/64 inch wide FITTING - grease, straight, 1/8 PT x 21/32 inch RING - external retaining. No. 50, 50 mm WASHER - flat, special, 2-1/32 ID x 4 OD x 1/16 inch thick PIN - axle pivot WASHER-thrust, 2-1/16x4-1/2x3/16 inch SHAFT ASSEMBLY - drive, front drive axle, parts list page 6-19 BOLT - hex, self-locking, 12 - 1.75 x 25 mm, class 10.9.. GUARD - drive shaft, used on models with 31 gallon fuel tank BOLT-hex, 12 - 1.75 X 45 mm, class 1 0 . 9 . . . WASHER - flat. 9/16 X 1-3/8x7/64 inch RETAINER - drive shaft, strap BOLT - special.I GUARD - drive shaft, used on models with 40 gallon fuel tank BRACKET - guard WASHER - flat, 9/16 X 1-3/8 x 7/64 inch BOLT - hex, 12 - 1.75 x 45 mm, class 10.9 NUT - hex, 12 mm -1.75, class 10

REQ'D. 1 16 : . .16 1 1 1 1 2 2 UAR 1 UAR 1 4 1 4 4 2 4 1 1 8 6 2

* NOTE: See page 5-5 for fittings used on two wheel drive steering hydraulics.

Bur 7-3350


6-4

BT97C001

580 Super L Series 2 Loader Backhoe FRONT DRIVE A X L E AXLE HOUSING REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

PART NO. 113561A1 144453A1 D149725 N14367 D149726 1966149C1 A156873 122270A1 136990A1 100522A1 1966186C1 1966191G1 100520A1 122268A1 144454A1 NSS .8301065 1966,13601 196613801 S301064 B17575

6-5

DESORIPTION REQ'p.AXLE ASSEMBLY - front drive, Oarraro No. 131204, parts list pages 6-5 -6-17 1 HOUSING - front axle., 1 BUSHING - rear pivot -1 SEAL - bushing, front and rear. . .; 2 BUSHING - front pivot 1 BREATHER - axle housing 1 PLUG - drain, 22 mm, housing and carrier :2 WASHER - Belleville, upper 2 WASHER - spacer, front axle 2 BUSHING - housing 2 BUSHING - housing 2 SEAL - oil 2 BUSHING - spherical, housing, lower 2 WASHER - Belleville, lower 2 OARRIER ASSEMBLY - differential 1 CARRIER - differentail 1 BOLT - hex, special, 14 mm x 75 mm .4 BUSHING - centering, carrier. 4 PIN - dowel, housing to carrier. 2 BOLT - hex flange, 12 x 33 mm, class 12.9, carrier to housing 10 SEALANT - black RTV silicone, 89 ml (3 ounce) tube, differential carrier to axle housing, not shown

UAR

NOTE: See page 6-3 for axle mounting.

Bur 7-3350


6-6

B9407020T

580 Super L Series 2 Loader Backhoe FRONT DRIVE A X L E SWIVEL HOUSING REF.

PART NO. 113561A1

1 2 3

144455A1 144456A1 100532A1

4 5 6 7 8 9 10 11

100529A1 1537663C1 1537664C1 712998R91 100533A1 122265A1 122264A1 N13505 B17575.

Bur 7-3350

6-7

DESCRIPTION REQ'D: AXLE ASSEMBLY - front drive, Carraro No. 131204, parts list pages 6-5 -6-17 1 HOUSING - swivel, left-hand, includes item 3, 100532A1 bushing 1 HOUSING - swivel, right-hand 1 BUSHING - swivel housing, used with right-hand orileft-hand. swivel housing .1 SEAL - oil, swivel housing 2 NUT - hex, special, 16 mm 2 BOLT - special; steering stop, 16 mm 2 FITTING - grease, straight, swivel cap 2 BOLT - hex, special 16 PIN - king, swivel housing cap, upper 2 PIN - king, swivel housing cap, lower 2 FITTING - grease, 45 degree, special, swivel cap .2 SEALANT - black RTV silicone, 89 ml (3 ounce) tube, wear ring to swivel housing, not shown

UAR


6-8

PART NO. 113561A1

1 2 3 4 5

144457A1 NSS 934727R1 112509A1 905839R1 144458A1

6 7 8 9

D149738 144459A1 D149737 114296A1

10 11 12 13 14 15 16

*NSS *NSS *NSS *NSS *NSS *NSS *NSS * D149739 B17575

Bur 7-3350

6-9

DESCRIPTION REQ'D. AXLE ASSEMBLY - front drive, Carraro No. 131204, parts list pages 6-5 -6-17 1 ARM ASSEMBLY - steering 2 JOINT - ball, swivel side 1 NUT - hex, special 1 JOINT - ball, right-hand threads 1 NUT - hex, self-locking, 18 x 1.5 mm 2 CYLINDER ASSEMBLY - steering, order. D149739 kit to service seals, see below 1 TUBE - cylinder 1 ROD - piston 1 GLAND - cylinder 1 BOLT - self-locking, special, steering cylinder, for service order 100524A1 bolt and 892-11012 washer 4 WIPER-rod........ ; 2 RING - backup 2 SEAL- rod -2 0-RING - gland 1 RING- wear . 2 SEAL - piston 1 0-RING - expander 1 KIT - seal, steering cylinder, for rod, gland, and piston, includes all items with an asterisk SEALANT - black RTV silicone, 89 ml (3 ounce) tube, cylinder flange to cylinder, not shown .

1 UAR


6-10


6-11

FRONT DRIVE A X L E AXLE SHAFTS REF.

1 2 3 4 5

PART NO. 113561A1 144461A1 144462A1 144464A1 N14410 144465A1 144463A1

Bur 7-3350

.

DESCRIPTION REQ'D. AXLE ASSEMBLY - front drive, Carraro No. 131204, parts list pages 6-5 - 6-17, see page 6-3 for mounting 1 SHAFT ASSEMBLY - axle, front and rear, order items 1-5 2 SHAFT - axle, differential side, long 2 BODY - connecting • • • -2 RING - snap, universal joint 16 JOINT - universal, axle shaft, cross 4 SHAFT - axle, wheel side, short 2


6-12

BS97M234

580 Super L Series 2 Loader Bacldioe

6-13

FRONT DRIVE A X L E PLANETARY REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 . 16 17 18 . 19 20 21 22 22A 23 24 25

PART NO. 113561A1 1984938C1 1966169C1 144466A1 NSS i00556A1 100552A1 100559A1 116426A1 116427A1 190684A1 190682A1 A48041 116425A1 100561A1 100554A1 100553A1 NSS ^ NSS K395093 800-1134 100555A1 100562A1 = 114295A1 K395091 100557A1 238-6121 905876R1 ' 496-81000 825-11418 B17575

Bur 7-3350

DESCRIPTION REQ'D. AXLE ASSEMBLY - front drive, Carraro No. 131204, parts list pages 6-5 -6-17. •< SEAL-oil, hub 2 BEARING - tapered roller, hub. 2 HUB ASSEMBLY - front drive axle 2 HUB - wheel attaching 1 STUD - hub, special -8 0-RING-wheel hub 2 RING - backup, wheel hub O-ring 2 , BUSHING - carrier.. .12 . CARRIER - ring gear 2 WASHER - thrust. 2 WASHER- thrust 2 RING - snap 2 BOLT - hex, self-locking, special 12 GEAR - ring, planetary 2 PLANETARY ASSEMBLY - front drive axle. . 2 CARRIER ASSEMBLY - planetary 2 CARRIER - planetary 1 SHAFT - pinion gear 3 PIN-locking 1 RING - external retaining. No. 34 -6 RETAINER - pinion gear. • -2 GEAR - pinion, planetary 6 BEARING - needle, planetary gear, packet of 10 18 WASHER - thrust, pinion gear, outer 6 PLUG-drain 2 0-RING -1-1/16 ID X 3/32 inch wide 1 SCREW - special, planetary cover plate 4 WASHER - flat, 25/32 x 1-3/8 x 1/8 inch, hardened 16 NUT-hex, 18 mm-1.5 16 SEALANT - black RTV silicone, 89 ml (3 ounce) tube, planetary cover to hub, not shown

UAR


6-14

era

B9407024S


6-15

FRONT DRIVE A X L E DIFFERENTIAL REF.

1 2 3 4 5

PART NO. 113561A1 109686A1 NSS NSS 827-10075 1967003C1 * N14407 * K395087 * N14408

8

* K395075

9 10 11 12 13

1966153C1 112486A1 1966559C1 K395027 *K395086 B17575 * 231397A1

Bur 7-3350

DESCRIPTION REQ'D. AXLE ASSEMBLY - front drive, Carraro No. 131204, parts list pages 6-5 -6-17 1 HOUSING ASSEMBLY - differential 1 HOUSING - differential, flange half 1 HOUSING - differential, plain half. 1 BOLT - hex, 10 - 1.5 x 75 mm, class 10.9 12 WASHER - thrust, differential housing 2 GEAR - side, differential, no longer available, for service order 231397A1 set. . 2 SHAFT - pinion gear, no longer available, for service order 231397A1 set 1 GEAR - pinion, differential, no longer available, for service order 231397A1 set 2 WASHER - thrust, pinion gear, no longer available, for service order 231397A1 set 2 BRACKET - lock 2 BOLT - hex, self-locking, special, 6 - 1 x 12 mm 2 RING - locking, threaded .2 BEARING - tapered roller, differential 2 PIN - dowel, no longer available, for service order 231397A1 set 1 SEALANT - black RTV silicone, 89 ml (3 ounce).tube, bolt to differential housing, not shown ,... SET - gear, differential, service replacement, includes Ref 5-8 and 13

UAR 1


6-16

B9407025S


6-17

FRONT DRIVE AXLE RING AND PINION GEAR SET REF.

1 2 3 4 5 6 7 7 7 7 7 7 7 7 7 7 8 9 10 11

PART NO. 113561A1 144460A1 NSS NSS K261065 K261014 13.49058C1 1349059C1 140954A1 140953A1 140951A1 140949A1 140948A1 140943A1 140944A1 140945A1 140946A1 140947A1 K395090 K262143 238-5152 128570A1 B17575

Bur 7-3350

DESCRIPTION REQ'D. AXLE ASSEMBLY - front drive, Carraro No. 131204, parts list pages 6-5 -6-17 GEAR - set, ring and pinion GEAR - ring, differential GEAR - pinion, differential WASHER - special RING - nut, pinion gear SPACER - collapsible WASHER - spacer 2 SHIM - 2.5 mm (0.098 inch) thick UAR SHIM - 2.6 mm (0.102 inch) thick UAR SHIM - 2.7 mm (0.106 inch)thick -UAR SHIM - 2.8 mm (0.110 inch) thick. UAR SHIM - 2.9 mm (0.114 inch) thick UAR SHIM - 3.0 mm (0.118 inch) thick UAR SHIM - 3.1 mm (0.122 inch) thick UAR SHIM - 3.2 mm (0.125 inch) thick UAR SHIM - 3.3 mm (0.129 inch) thick. UAR SHIM - 3.4 mm (0.133 inch) thick UAR BEARING - tapered roller, pinion gear 2 SEAL -oil 1 0-RING - 3-1/4 ID X 3/32 inch wide 1 COVER - differential 1 SEALANT - black RTV silicone, 89 ml (3 ounce) tube, differential cover to differential carrier, not shown

UAR


6-18

6r19


DRIVE SHAFT FOR FRONT DRIVE AXLE FRONT DRIVE AXLE TO TRANSMISSION

REF.

9 10 11 12

PART NO. 284713A1 144278A1 NSS NSS NSS 219-10 NSS 144279A1 219-10 D149860 NSS NSS NSS 90-6682T1

13

D137627

2 3 4 5 6 7 8

Bur 7-3350

DESCRIPTION SHAFT ASSEMBLY - drive, fronf drive axle KIT - universal joint JOINT - universal, drive shaft BEARING - universal joint RING - retaining FITTING - grease, straight, 1/4-28 taper x 11/16 inch SHAFT - drive, transmission to rear axle YOKE - tube, spiined, to rear axle FITTING - grease, straight, 1/4-28 taper x 11/16 inch KIT - dust cap WASHER - cork WASHERsteel CAP - dust seal retaining RETAINER - drive shaft, strap, not included with the drive shaft assembly, purchase separately. BOLT - special

REQ'D. 1 .2 1 4 4 2

2 4


6-20

6-21


TRANSMISSION COOLING SYSTEM

USED WITH 239739A1 HEAVY DUTY RADIATOR ASSEMBLY REF. 1

PART NO. 291288A1

2 3 5 6 10 11 12 13 14

614-10020 895-11010 292962A1 243805A2 LI 8337 218-5137 237-6010 233972A1 234719A1 345-44 • 233970A1 233971A1 234499A1

15 16 17

Bur 7-3350

DESCRIPTION REQ'D. COOLER - hydraulic oil, heavy duty, used with 239739A1 heavy duty radiator on page 2-5, uses radiator upper mounting bolts, see page 9-83. for hardware and page 8-9 for additional cooler hydraulic routing, includes Ref 17 1 BOLT - hex, full threads, 10 -1.5 x 20 mm 2 WASHER-fiat, 11 x 2 0 x 2 mm 2 HOSE - 1240 mm (48-7/8 inch) long, transmission to cooler inlet .1 HOSE - 1563 mm (61-9/16 inch) long, cooler outlet to transmission 1 STRAP-tie, 15 inch, nylon, retaining . .3 ELBOW - 45 degree, 7/8-14 inch flare x adj 0-ring boss 2 O-RING - 3/4 ID X 3/32 inch wide . .1 SEAL - 564 mm (22-7/32 inch) long, horizontal, cooler to wrapper 1 SEAL - 70 X 100 X 32 mm, upper corner 2 ADHESIVE - spray can, 3M No. 74, 23 dunce UAR SEAL - 472 mm (18-5/8 inch) long, vertical, cooler to wrapper .2 SEAL -103 mm (4-1/16 inch) long, lower corner. ' 2 SEAL - 45 X 120 X 15 mm, furnished with cooler 2


6-22


6-23

TRANSMISSION MOUNTING, DRIVE SHAFT, DIPSTICK AND GEAR SHIFT LEVER REF. 1 2 3 4 5 6

PART NO. +187714A1 +187715A1 + 484-6316 + 459-11014. + 493-41020 +179689A1

7 • 8 9 10 11 12 13 14

+190618A1 + 280-16516 + 828-12055 + 495-11053 + 832-10412 + 126-116 +143370A1 *123842A2

15

*123843A2

16 17 20 21 21

627-10035 496-21041 121658A1 1995137C1 1995137C1C

21

1995137C1R

22 23 24 25 26 27 28 29 30 31 32 33 34

428-510 A15672 . A178706 496-21041 626-10016 614-12040 896-15012 - 284641A1 284723A1 814-16110 D35009 117846A1 83^-10416

DESCRIPTION REQ'D. KNOB - upper, cover 1 KNOB-lower 1 SCREW - set, hex socket headless, 5/16,NF x 3/8 inch, half dog point 1 SCREW - machine, pan head slotted, No. 10 NF x 7/8 inch 2 WASHER - external tooth lock, 3/16 inch 2 LEVER - transmission gear shift, see page 4-11 for clutch cutout harness and switch 1 BOOT - transmission gear shift lever 1 SCREW - self-tapping, hex washer head. No. 10 - 16 x 1 inch 4 BOLT - hex, 12 - 1.75 x 55 mm, class 10.9 1 WASHER-flat, 17/32x1-1/16x3/32 inch 1 NUT - hex, self-locking, 12 mm -1.75 1 KEY - Woodruff, 3/16 x 3/4 inch 1 SPRING - return, shift lever 1 TRANSMISSION ASSEMBLY - two wheel drive, parts list pages 6-27 6-49 1 TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51 1 BOLT - hex, full threads, 10 -1.5 x 35 mm, class 10.9 .12. WASHER - flat, 13/32 x 13/16 x 3/32 inch, hardened 12 DIPSTICK - oil level, transmission 1 CONVERTER - torque, new . . . . 1 RETURN NUMBER - torque converter core, use this part number to return torque converter for credit when using a remanufactured assembly 1 CONVERTER - torque, remanufactured. North America only, component parts not serviced separately .1 BOLT - hex, 5/16 NF x 5/8 inch, grade 8 6 WASHER - flat, hardened, special.. 6 PLATE - adapter, torque converter to engine flywheel 1 WASHER - flat, 13/32 x 13/16 x 3/32 inch, hardened 6 BOLT - hex, full threads, 10 -1.5 x 16 mm, class 10.9 . . . . : : .6 BOLT - hex, full threads, 12 - 1.75 x 40 mm 7 WASHER - flat, 13.5 x 28 x 4 mm, hardened 7 BRACKET - mounting, transmission, right-hand 1 BRACKET - mounting, transmission, left-hand 1 BOLT-hex, 1 6 - 2 . 0 x 1 1 0 mm 2 WASHER - flat, special, 5/8 inch, hardened .6 INSULATOR - engine mount, rear 2 NUT - hex, self-locking, 16 mm - 2.0 2

+ NOTE: Used on models without powershift transmissions. * NOTE: See page 6-27 for remanufactured transmission part numbers. Continued on next page

Bur 7-3350


6-24

BS97M188


6-25

TRANSMISSION MOUNTING, DRIVE SHAFT, DIPSTICK AND GEAR SHIFT LEVER REF. 35

PART NO. 284712A1

37

2983,94A1

38 39 40 41 42

218-459 237948A1 90-6682T1 D137627 292514A1

Bur 7-3350

DESCRIPTION SHAFT ASSEMBLY - drive, transmission to rear axle, parts list page 6-69 SEAL - foam, transmission control lever, installed between firewall and flange on four speed shift lever boot, cab models only ADAPTER - straight, 1-5/16-12 flare x 3/4 inch PT TUBE - transmission dipstick RETAINER - drive shaft, strap BOLT - special SEAL - foam, noise reduction, cab models

REQ'D. 1 1 1 1 2 4 1


6-26

J®

BT97M189


6-27

TRANSMISSION ASSEMBLY OIL FILTERS TWO WHEEL AND FOUR WHEEL DRIVE PART NO. 123842A2

REF.

123842A2C 123842A2R

123843A2 123843A2C 123843A2R

1 2 3 4 5 6 7 8 9 10 11 12

'

254686A1 181101A1 181274A1 181141A1 181196A1 190426A1 190433A1 278534A1 100748A1 181219A1 614-8018 181102A1

Bur 7-3350

DESCRIPTION TRANSMISSION ASSEMBLY - two wheel drive, new, parts list pages 6-27-6-49 RETURN NUMBER - transmission core, use this part number to return transmission for credit when using a remanufactured assembly TRANSMISSION ASSEMBLY - remanufactured. North America only, component parts shown on this page do not apply to the remanufactured assembly TRANSMISSION ASSEMBLY - four wheel drive, new, parts list pages 6-27-6-51 / . . . :.. RETURN NUMBER - transmission core, use this part number to return transmission for credit when using a remanufactured assembly TRANSMISSION ASSEMBLY - remanufactured. North America only, component parts shown on this page do not apply to the remanufactured assembly

REQ'D. 1 1 1 1 1 1

FILTER - oil, cartridge, transmission, 152 mm (6 inch) long 1 PLUG - oil, 14-1.5 mm, used on four wheel drive models only 1 KIT - valve, used on four wheel drive models only 1 O-RING - small, used on four wheel drive models only 1 PLUG - bypass valve, used on four wheel drive models only . . . 1 O-RING - bypass valve, cylinder, one (1) used at each end of item 7, cylinder bypass valve, used on four wheel drive modelslonly 2 CYLINDER -..bypass valve, used on four wheel drive models only . . . . . . . . . 1 FILTER - oil . . ...1 O-RING - sealing 1 COVER - access, oil filter 1 BOLT - hex, full threads, 8 - .1.25 x 18 mrh . . . . . . . . 2 PLUG - oil, used on four wheel drive models only 1


6-28

BT97C005

6-29


TRANSMISSION ASSEMBLY

TRANSMISSION HOUSING - TWO WHEEL DRIVE REF.

PART NO. 123842A2

1

181267A1

2 3 4 5 6

1530028C1 934667R1 181100A1 K260177 181197A1

7 8 8A 9 10

614-10030 100557A1 238-6121 814-10150 181268A1

11 12 13 14

181179A1 181105A1 •181232A1 181141A1

:

Bur 7-3350

DESCRIPTION TRANSMISSION ASSEMBLY - two wheel drive, parts list pages 6-27 6-49, see page 6-27 for remanufactured transmission part numbers HOUSING - front half, use with Loctite 510 or 518 as a gasket eliminator BREATHER - housing WASHER - flat, copper, special, 10 x 14 x 1.5 mm PLUG - housing PIN - dowel, special, 10 x 25 mm COVER - housing, rear half, use with Loctite 510 or 518 as a gasket eliminator BOLT - hex, full threads, 10 -1.5 x 30 mm PLUG-drain O-RING -1-1/16 ID x 3/32 inch wide BOLT - hex, 10 -1.5 x 150 mm HOUSING - rear half, use with Loctite 510 or 518 as.a gasket eliminator BOLT - hex, special . WASHER - flat, copper, special, 14 x 20 x 1.5 mm TUBE - oil lubrication O-RING - housing

REQ'D.I 1 1 1 .2 2 3 1 2$ 1 1 2 1 2 4 1 .3


6-30

0

BT97C004

o\

<

6-31


TRANSMISSION ASSEMBLY

TRANSIVIISSION HOUSING - FOUR WHEEL DRIVE REF.

PART NO. 123843A2

1

181200A1

1A 2 3 4 5 6

239606A1 1530028C1 934667R1 181100A1 K260177 181197A1

7 8 8A 9 10

614-10030 100557A1 238-6121 218-1023 181201A1

11 12 13 14 15

181179A1 181105A1 181232A1 181176A1 18'1141A1

Bur 7-3350

DESCRIPTION TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51, see page 6-27 for remanufactured transmission part numbers HOUSING - front half, use with Loctite 510 or 518 as a gasket eliminator PLUG - housing, oil passage port, not shown BREATHER - housing WASHER - flat, copper, special, 10 x 14 x 1.5 mm PLUG - housing -PIN - dowel, special, 10 x 25 mm COVER - housing, rear half, use with Loctite 510 or 518 as a gasket eliminator BOLT - hex, full threads, 10 -1.5 x 30 mm PLUG-drain O-RING - 1-1/16 ID X 3/32 inch wide ADAPTER - straight, 1/2-20 flare x 1/4 inch PT HOUSING - rear half, use with Loctite 510 or 518 as a gasket eliminator ^ BOLT - hex, special WASHER - flat, copper, special, 14 x 20 x 1.5 mm . . TUBE - oil lubrication TUBE-oil O-RING - housing.

REQ'D. 1 1 1 1 2 2 3 1 23 1 1 2 1 2 4 1 • -1 3


6-32

BT95G027

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y OIL PUMP TWO WHEEL OR FOUR WHEEL DRIVE REF.

PART NO. * 123842A2 *123843A2

1 2 3 3A 4 5

181199A4 247744A1 181270A1 %NSS 198713A1 181109A1

6 7

%NSS 864-6025

8 9 10 11 12

NSS 181145A1 181214A1 198712A1 181215A1

13

247746A1

14 15 16 17 18

181216A1 181205A1 814-8060 NSS 247748A1

19 20

181142A1 246767A1

21

181218A1

%247749A1

6-33

DESCRIPTION REQ'D. TRANSMISSION ASSEMBLY - two wheel drive, parts list pages 6-27 6-49 . 1 TRANSMISSION ASSEMBLY four wheel drive, parts list pages 6-27 6-51 1 PUMP ASSEMBLY - oil, transmission .1 SHAFT - small, not available for service, order 181199A4 pump 1 SPRING - detent, not available for service, order 181199A4 pump 1 PIN - valve, order 247749A1 piston valve kit below 1 STOP - spring, not available for service, order 181199A4 pump 1 PIN - roll, 5 X 22 mm, not available for service, order 181199A4 pump 2 VALVE - piston, order 247749Al piston valve kit below 1 BOLT - hex socket, 6 - 1 . 0 x 25 mm, not available for service, order 181199A4 pump 2' SUPPORT - pump . .1 BALL - check, not available for service, order 181199A4 pump. . . . .1 SPRING - detent, not available for service, order 181199A4 pump . .1 GUIDE - spring, not available for service, order 181199A4 pump . . .1 BUSHING - pump support, small, not available for service, order 181199A4 pump BUSHING - pump support, large, not available for service, order 181199A4 pump BUSHING - pump housing SEAL - oil, pumjD housing BOLT - hex, 8 - 1.25 x 60 mm 6 HOUSING - oil pump GEAR - 23 teeth, charge pump, large, not available for service, order 181199A4 pump O-RING - pump housing BEARING - needle, not available for service, order 181199A4 pump GEAR - small, 12 teeth, not available for service, order 181199A4 pump. • KIT - piston valve, not available for service, order 181199A4 pump ,

* NOTE: See page 6-27 for remanufactured transmission part numbers.

Bur 7-3350


6-34

BT97C003

6^35

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y TRANSMISSION SHIFTER MECHANISM TWO WHEEL OR FOUR WHEEL DRIVE REF.

PART NO. *123842A2 *123843A2 %NSS

2 3 4 5 6 7 8

614-12016 1966835C1 1966993C1 181139A1 864-8025 181171A1 %NSS

9

%NSS

10

%NSS

11 12 13

181177A1 181138A1 %NSS

14

15 16 17 18 19 20

NSS

NSS

181173A1 864-10025 181175A1 181245A2 %905794R1 %256888A3

DESCRIPTION TRANSMISSION ASSEMBLY - two wheel drive, parts list pages 6-27 6-49 TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51 RAIL - shifter fork, third and fourth, no longer included in transmission assembly, order 256888A3 synchronizer kit, see below BOLT - hex, full threads, 12 - 1.75 x 16 mm WASHER - flat, special, 12 x 16 x 1.5 mm SPRING - detent BALL-detent BOLT - hex socket, 8 - 1.25 x 25 mm COVER - shift lever LEVER - shift, replaces 190428A1, 190428A2 and 190428A3 lever, includes bushing and retaining ring, no longer included in transmission assembly, order 256888A3 kit PIN - shift lever, replaces 1967585C1 pin, no longer included in transmission assembly, order 256888A3 synchronizer kit, see below BOOT - rubber, replaces 1967581 C I boot, no longer included in transmission assembly, order 256888A3 synchronizer kit, see.below CLAMP - adjustable O-RING - sealing SPRING - shift lever, replaces 1967586C1 and 190436A1 spring, no longer included in transmission assembly, order 256888A3 kit BUSHING - shift lever, replaces 181180A1 bushing, no longer included in transmission assembly, bushing is now part of 190428A3 lever, Ref 8, which is not serviced separately, order 256888A3 kit RING - external retaining, replaces 800-1115 ring, no longer included in transmission assembly, ring is now part of 190428A3 lever, Ref 8, which is not serviced separately, order 256888A3 kit SHIFTER-rail BOLT - hex socket, 10 - 1 . 5 x 25 mm PLATE - retainer, detent ball RAIL - shifter fork, first and second PIN - roll, 6 x 30 mm

REQ'D. 1 1 1 .3 3 2 4 3 1

.1 2 1 1 1 1

1

1 2 2 1 1 2-4

KIT - synchronizer service, replaces 256888A2 kit, includes parts on pages 6-35, 6-37, 6T41 and 6-43, also includes (1 each) 278531A1 washer, 278532A1 bushing, 278533A1 spring and 279039A1 shift lever snap ring which are not sen/iced separately and not shown

* N O T E : See page 6-27 for remanufactured transmission part numbers. Continued on next page

Bur 7-3350


6-36

BT97C003

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y TRANSMISSION SHIFTER MECHANISM TWO WHEEL OR FOUR WHEEL DRIVE REF.

PART NO. *123842A2 * 123843A2

21 22

181203A1 iNSS

23 24 25

181104A1 181275A1 614-8016 %256888A3

6-37

DESCRIPTION TRANSMISSION ASSEMBLY - two wheel drive, parts list pages 6-27 6-49 TRANSMISSION ASSEMBLY . four wheel drive, parts list pages 6-27 6-51 FORK - gear shift, first and second FORK - gear shift, third and fourth, replaces 181174A1 and 181174A2 fork, no longer included in transmission assembly, order 256888A3kit WASHER - sealing, copper BOLT - hex, special BOLT - hex, full threads, 8 - 1 . 2 5 x 16 mm . . . . . . . . . . .

REQ'D.

;l

KIT - synchronizer service, replaces 256888A2 kit, includes parts on pages 6-35, 6-37, 6-41 and 6-43, also includes (1 each) 278531A1 washer, 278532A1 bushing, 278533A1 spring and 279039A1 shift lever snap ring which are not serviced separately and not shown

• N O T E : See page 6-27 for remanufactured transmission part numbers.

Bur 7-3350:"

Issued February,. 1998

6-38

B9407070T

6-39

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y IDLER AND PRIMARY SHAFT TWO WHEEL OR FOUR WHEEL DRIVE REF.

PART NO. *123842A2 *123843A2

1 . 2 3 4 5 6 7 8 9 10 11 12

ST205A 181151A1 181186A1 181181A1 181186A1 A48041 181128A1 181154A1 181188A1 181187A1 181184A1 181132A1

DESCRIPTION TRANSMISSION ASSEMBLY - two wheel drive, parts list;pages 6-27 6-49 TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51 . . BEARING-ball SHIM - bearing, 52 x 35.1 x 4 mm GEAR - idler, 27 teeth SHAFT - idler GEAR - idler, 27 teeth RING-snap BEARING-ball WASHER - thrust, 65 x 45 mm. GEAR - drive, third, 28 teeth GEAR - drive, fourth, 39 teeth SHAFT - primary BEARING - roller

REQ'Dl

1 2 2 1 1 1 1 1 1 1 1 .1 1


Bur 7-3350


6-40

580 Super L Series 2 Loader Backlioe TRANSMISSION A S S E M B L Y INPUT SHAFT TWO WHEEL OR FOUR WHEEL DRIVE REF.

PART. NO. *123842A2 *123843A2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

181152A3 A48041 181128A1 181153A1 181154A1 181135A1 181228A2 181162A1 181.116A1 181163A1 181159A1 181158A1 181111A1 181161 A l %NSS

16

%NSS

17 18 19 20 21 22 23 24

181157A3 181156A3 181108A1 298203A1 D142898 181227A2 181164A1 181126A1 S256888A3

6-41

DESCRIPTION TRANSMISSION-ASSEMBLY - two whedl drive, parts list pages 6-27 6-49 TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51 SEAL-oil RING - snap BEARING-ball SPACER - bearing = WASHER - thrust, 65 x 45 mm BEARING - needle GEAR - input shaft, 35 teeth PLATE - thrust R I N G - lock W A S H E R - thrust PLATE - disc, intermediate. P L A T E - d i s c , clutch RING-snap . PLATE - pressure SPRING - detent;Teplaces 181160A1 and 181160A2:spring, no longer included in transmission assembly, order 256888A3 synchronizer kit, see below ' PISTON - input shaft, replaces 181155A1 and 181155A2 piston, no longer included in transmission assembly, order 256888A3 synchronizer kit, see below RING-seal ; RING - seal, small PIN - roll SHAFT-input PLUG-inputshaft G E A R - s h a f t , 29 t e e t h . SPACER - bearing B E A R I N G - ball

REO'D. |1 •

.1 1

KIT - synchronizer service, replaces 256888A2 kit, includes parts on pages 6-35, 6-37, 6-41 and 6-43, also includes.(1 each) 278531 A l washer, 278532A1 bushing, 278533A1 spring and 279039A1 shift lever snap ring which are not serviced separately and not shown


Bur7-3350

Issued February, 1998.

6-42

0

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y SECONDARY SHAFT TWO WHEEL OR FOUR WHEEL DRIVE REF.

6-43;

DESCRIPTION

PART NO.

REO'D;

*123842A2

T R A N S M I S S I O N A S S E M B L Y - two wheel drive, parts list pages 6 - 2 7 -

*123843A2

T R A N S M I S S I O N A S S E M B L Y - four wheel drive, parts list pages 6 - 2 7 -

6-49

•••

1

6-51

3

181193A1

RING-lock B E A R I N G - roller W A S H E R - thrust, 6 4 x 4 0 mm

4

181190A1

G E A R - driven, second, 4 3 teeth

5

181114A1

R I N G - snap

1

181118A1

2

181132A1

%NSS

%NSS

K I T - synchronizing service, replaces 1 9 0 4 2 7 A 1 kit, no longer included in transmission assembly or serviced separately, order 2 5 6 8 8 8 A 3 synchronizer kit, see be\o\N S P A C E R - replaces 2 4 4 1 0 9 A 1 spacer, gear to synchronizer ring, no longer included in kit or transmission assembly, order 2 5 6 8 8 8 A 3 synchronizer kit, see below

2

7

NSS

R I N G - synchronizer...

2

8

NSS

R I N G - synchronizer, flanged

2

9

NSS

10

NSS

SPACER-hub R E T A I N E R - spacer

2 2

11

NSS

H U B - synchronizer. . . .

1

12

NSS

SPRING-hub

13

NSS

BALL-hub - P L A T E - spring SLEEVE-hub

3 3 3

14

NSS

.15

NSS

16

181189A1

17

181226A1

18

181224A1

19

181192A1 %256888A3

G E A R - driven, first, 4 9 teeth S P A C E R - gear,=tw6^wheel drive models G E A R - drive, M F D , 4 4 teeth • G E A R - driven, fourth, 2 3 teeth . . . K I T - synchronizer service, replaces 2 5 6 8 8 8 A 2 kit, includes parts on pages 6 - 3 5 , 6 - 3 7 , 6 - 4 1 and 6-43,'also includes (1 each) 2 7 8 5 3 1 A 1 washer, 2 7 8 5 3 2 A 1 bushing, 2 7 8 5 3 3 A 1 spring and 2 7 9 0 3 9 A 1 shift lever snap ring which are not serviced separately and not shown

* NOTE: See page 6 - 2 7 for remanufactured transmission part numbers. Continued on next page

Bur 7 - 3 3 5 0

Issued February, 1 9 9 8

6-44

PART NO. *123842A2 * 123843A2 181178A1

20

241957A1

21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

123800A1 NSS 1967506C1 123803A1 1967537C1 181lb8A1 181183A1 181191A1 181154A1 181130A1 181123A1 233284A1 181144A1 181165A1 P3533055

6-45

DESCRIPTION REQ'D. TRANSMISSION ASSEMBLY - two wheel drive, parts list pages 6-27 6-49 TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51 1 KIT - synchronizing service, kit no longer available, order 256888A3 synchronizer service kit, see below . FLANGE - synchronizer, no longer included in kit, purchase separately RING - synchronizer HUB - synchronizer SPRING - hub, inner SPRING - hub, outer SLEEVE - shift fork, no longer included in kit, purchase separately PIN-roll........ SHAFT - secondary GEAR - driven, third, 33 teeth WASHER - thrust, 65 x 45 mm BEARING - ball SEAL - oil, 60 X 75 X 8 mm YOLK - shaft, rear 0-RING - flange sealing WASHER - flat, special, 52 x 12.5 x 5 mm SCREW - locking, special, 12 - 1.25 x 25 mm

*.NOTE: See page 6-27 for remanufactured transmission part numbers.

Bur 7-3350


6-46

0

B9407072T

6-47

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y FOUR WHEEL DRIVE OUTPUT SHAFT REF.

PART NO. *123843A2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 . 16 17 18 19 20 21 22

233283A1 614-8022 181198A1 112517A1 181.122A1 ST205A ., 181152A3 181194A1 181126A1 18li54A1 181223A1 100747A1 181182A1 100748A1 181248A1 D142898 100753A1 181276A1 181120A1 P3533055 P2745466 238-8217

DESCRIPTION TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51 •• YOLK - shaft, front BOLT - hex, full threads, 8 - 1.25 x 22 mm COVER - front O-RING - cover SEAL - oil, 50 X 65 X 8 mm B E A R I N G - ball SEAL-oil BUSHING - grooved BEARING-ball WASHER - thrust, 65 x 45 mm GEAR - driven, MFD, 36 teeth O-RlNG - shaft, large SHAFT-output O-RING - shaft, small SLEEVE-shaft P L U G - s h a f t , 1 0 x 1 mm SPRING - sleeve WASHER - flat, special RING - snap SCREW - locking, special, 12 - 1.25 x 25 mm WASHER - fiat, special . O-RING -1-3/16 ID X 1/8 inch wide .

REQ'D


Bur 7-3350


6-48

29)

BT97C002

(Te)

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y TRANSMISSION CONTROL VALVE TWO WHEEL OR FOUR WHEEL DRIVE REF.

PART NO. *123842A2 *123843A2

1 2 3 4 5 " 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 35 36 37 38

190434A1 NSS 190442A1 190443A1 190437A1 181136A1 181273A1 181272A1 864-6020 181251A1 181256A1 190439A1 190438A1 190435A1 190441A1 181234A1 299324A1 181261A1 181146A1 181107A1 181103A1 864-8020 181166A1 181207A1 181208A1 181254A1 181260A1 181255A1 181137A1 181258A1 181262A1 181253A1 190444A1 814-8080 181100A1 934667R1 190436A1 190440A1

6-49

DESCRIPTION TRANSMISSION ASSEMBLY - two wheel drive, parts list pages 6-27 6-49 TRANSMISSION ASSEMBLY - four wheel drive, parts list pages 6-27 6-51 VALVE ASSEMBLY - transmission control BODY - transmission control valve PLUNGER - solenoid • COIL - solenoid CONNECTOR - solenoid 0-RING - sealing WASHER - sealing, copper PLUG-hex, cap BOLT - hex socket, 6 -1.0 x 20 mm COVER - modulation GASKET-cover SPACER - gasket PISTON - modulation, outer SPRING - inner. SPRING - outer PISTON - modulation, inner RING - snap SPRING - check BALL-check WASHER - sealing, copper: PLUG-oil BOLT - hex socket, 8 - 1.25 x 20 mm GASKET - body to valve plate PLATE-valve GASKET - valve plate to transmission housing SHAFT - flow divider SPRING - piston PISTON - flow divider 0-RING-plug PLUG - valve SPRING - spool SPACER - spring SPOOL - fonward/reverse BOLT - hex, 8 - 1.25 x 80 mm PLUG - valve. . WASHER - flat, copper, special, 10 x 14 x 1.5 mm SPRING - piston, outer modulation PIN - piston, inner modulation

^

REQ'D.

l" ^ } • • -f I } f • • '} ? } } •} •} 1 ? 1 1 1 1 -3 1 1 1 ] 1 1 3 ? 2 2 1 • • -6 1 4 lj "li

' NOTE: See page 6-27 for remanufactured transmission part numbers.

Bur 7-3350


6-50

580 Super L Series 2 Loader Backhoe TRANSMISSION A S S E M B L Y SOLENOID VALVE - FOUR WHEEL DRIVE REF.

PART NO. *123843A2

1 2 3 4

190432A1 NSS NSS NSS 181149A1

5 6 7 8 9 10

181100A1 934667R1 814-8060 190429A1 190430A1 190431A1

6-51

DESCRIPTION TRANSMISSION ASSEMBLY - four wheel drive, parts list;pages 6-27 6-51 VALVE ASSEMBLY - solenoid NUT-cap COIL - solenoid VALVE - solenoid . . KIT - seal, solenoid, includes (1 each) 238-5014, 238-5015 and 237-6010 0-ring, not available for service, order 190432A1 valve PLUG - valve WASHER - fiat, copper, special, 10 x 14 x 1.5 mm BOLT - hex, 8 - 1.25 x 60 mm r BODY - solenoid valve GASKET - body to transmission housing VALVE - solenoid, installed between item 8 and item 9:

REQ'D.


Bur 7-3350


6-52

^l•v'••^v>;,••'-•^rfi^^

B9408129S


6-53

REAR W H E E L S AND T I R E S TWO WHEEL OR FOUR WHEEL DRIVE REF.

PART NO.

DESCRIPTION

REO'D.

19.5LX24 T I R E S - 1 0 PLY 1 2 3

104907A1 A20058 REF

WHEEL-rim VALVE - stem, wheel TIRE - rear, purchase locally.

2 2 2

17.5LX24TIRES-10PLY 1 2 3

119241A1 A20058 REF

WHEEL - rim VALVE - stem, wheel TIRE - rear, purchase locally

2 .2 2

WHEEL NUTS 4 5

D138380 D138492

Bur 7-3350

WASHER - flat, hardened, special NUT - hex, special, 22 mm -1.5

20 . .20


6-54

BT97M190

580 Super L Series 2 Loader Baickhoe

6r55

REAR DRIVE A X L E MOUNTING REF. 1 2 3 4 5 6 7

PART NO. 279169A1 D.I 38492 ,D138380 827-20230 896-11020 117933A1 829-1420

Bur 7-3350

DESCRIPTION AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 NUT - hex, special, 22 mm -1.5 WASHER - flat, hardened, special BOLT - hex, 20 - 2.5 x 230 mm, class 10.9 WASHER - flat, 22 x 37 x 4 mm, hardened PLATE - axle mouhting NUT - hex, 20 mm - 2.5, class 10

REQ'D. .1 20 20 8 • -16 2 8


6-56

'•Am

BT97N120


6-57

REAR A X L E DIFFERENTIAL L O C K REF. 1

PART NO. 218-5105

2 3 4 5

237-6006 218-5057 237-6006 304019A1

8 9 10 11 12 13 14 15

L18337 283579A1 297255A1 184505A1 237- 6008 238- 5013 238-5014 NSS

16 17 18 19 20 21 23 24

NSS 614-6050 895-11006 892-11006 829-1406 304020A1 LI 8337 218-5135

25

237-6006

Bur 7-3350

DESCRIPTION REQ'D. ELBOW - 90 degree, 9/16-18 inch flare x adj 0-ring boss, four used on models without powershift transmissions; five used on models with powershift transmissions 4-5 0-RING -15/32 ID x 5/64 inch wide 1 ADAPTER - straight, 9/16-18 inch flare x 0-ring boss 1 0-RING -15/32 ID x 5/64 inch wide 1 HOSE - 1200 mm (47-1/4 inch) long, transmission supply and return lines, transmission to solenoid valve 2 STRAP-tie, 15 inch 2 VALVE ASSEMBLY - solenoid, differential lock 1 MANIFOLD - valve 1 SOLENOID ASSEMBLY - valve, 12 volt 1 0-RING - 41/64 ID x 3/32 inch wide 1 0-RING - 7/16 ID X 1/16 inch wide 1 O-RING -1/2 ID X 1/16 inch wide 1 VALVE - solenoid, cartridge, component parts are not serviced separately 1 COIL - solenoid 1 BOLT - hex, full threads, 6 -1.0 x 50 mm 2 WASHER - flat, 6.6 x 12 x 1.6 mm 2 WASHER - lock, 6 mm 2 NUT - hex, 6 mm -1.0, class 10 2 HOSE - 625 mm (24-5/8 inch) long, solenoid valve to rear axle 1 STRAP-tie, 15 inch 1 ELBOW - 45 degree, 9/16-18 inch flare x adj O-ring boss, axle port location shown is for models without powershift transmission; for models with powershift the elbow is located on the opposite side of the axle input shaft 1 0-RING -15/32 ID x 5/64 inch wide 1


6-58

ART 180

BT97M192

ROTATED DEGREES

580 Super L Series 2 Loader Backhoe REAR DRIVE A X L E AXLE HOUSING REF. 1 1A 2 3 4 7 8 9 10 11 12 13 14 18 19 20 21

PART NO. 279169A1 100557A1 238-6121 238-5270 190457A2 295114A1 190458A2 190459A1 814-14140 864-12130 295108A1 295109A1 1966149C2 175955A1 El 35750 192481A1 222688A1 100760A1

Bur7-3350

6-59

DESCRIPTION REQ'D. AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 . . . . . . .1 PLUG - drain • • -2 0-RING -1-1/16 ID x 3/32 inch wide • -I O-RING - 9 ID X 1/8 inch wide • • -6 CYLINDER - brake, right-hand 1 HOUSING - center, axle • • •-1 CYLINDER - brake, left-hand 1 SLEEVE - gear housing 2 BOLT - hex, 14 - 2.0 x 140 mm • • -22 BOLT - hex socket, 12 - 1.75 x 130 mm 4 HOUSING - axle, left-hand side HOUSING - axle, right-hand side BREATHER - axle housing COVER - breather, if used fEXTENSION - breather SWITCH - oil temperature, may have one or two wires^ TUBE ^ internal: O-RING - sealing, tube 2


6-60

18

580 Super L Series 2 Loader Backhoe R E A R DRIVE A X L E DIFFERENTIAL REF. 1 2 3 4

PART NO. 279169A1 292268A1 NSS NSS * E135777 * 190471A1 * D142971

6 7 8 9 10 11 12 13 14 15 16

* 190469A1 S300976 El 35785 P3034505 112486A1 175959A1 292207A1 292208A1 190452A1 191067A1 * 190468A1

17

*292890A1

18 19

D143033 175961A1 *294192A1

Bur 7-3350

6-61

DESCRIPTION REO'D. AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 1 HOUSING ASSEMBLY - differential 1 HOUSING - differential, flange half 1 HOUSING - differential, plain half 1 WASH E R - th rust 4 GEAR - sun, 12 teeth, no longer sold separately, must be replaced as a set, for service order 294192A1 gear set, see below 4 GEAR - side, pinion, no longer sold separately, must be replaced as a set, for service order 294192A1 gear set, see below 1 WASHER - thrust 2 BOLT - hex, special, 12 - 1.75 x 90 mm, class 12.9 10 BEARING - cup and cone 2 RING - locking, threaded 2 BOLT - hex, self-locking, special, 6 - 1 x 12 mm 2 BRACKET - lock 2 PIN - housing 4 O-RING-pin 4 BUSHING - housing 2 SLEEVE - housing 1 SHAFT - sun gear, no longer sold separately, must be replaced as a set, for service order 294192A1 gear set, see below 2 GEAR - side pinion, no longer sold separately, must be replaced as a set, for service order 294192A1 gear set, see below 1 PIN - dowel, 12 x 40 mm 2 RING-lock 1 SET - gear, differential, service replacement, includes items 3-6, 16 and 17

1


6-62


6-63

REAR DRIVE A X L E RING AND PINION GEAR SET REF. 1 2 3 4 5 6 7 7 7 7 ,7 7 7 7 7 7 8 9 10 11 12,

PART NO. 279169A1 294189A1 NSS NSS K261065 K261014 1349059C1 295110A1 190506A1 190508A1 190509A1 190510A1 190511A1 190512A1 190513A1 190514A1 190515A1 190516A1 El 35762 128570A1 K395090 238-5152 K262143

Bur 7-3350

DESCRIPTION AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 GEAR - set, ring and pinion GEAR - ring, differential GEAR - pinion, differential WASHER - special RING - nut, pinion gear WASHER - spacer SPACER - collapsible SHIM -2.5 mm (0.098 nch) thick SHIM-2.6 mm (0.102 nch) thick.. SHIM-2.7 mm (0.106 nch) thick. SHIM-2.8 mm (0.110 nch) thick SHIM-2.9 mm (0.114 nch) thick./. SHIM-3.0 mm (0.118 nch) t h i c k . . . ; SHIM-3.1 mm (0.122 nch) thick. SHIM-3.2 mm (0.125 nch)thick SHIM-3.3 mm (0.129 nch) t h i c k . . . . . SHIM-3.4 mm (0.133 nch) thick. BEARING - 45 X 100 mm, pinion gear. . . . COVER - differential. . . . BEARING - tapered roller, pinion gear. . .. O-RING - 3-1/4 ID X 3/32 inch wide, cover. SEAL - o i l . . . . . . .

REQ'D.

• -2 ^ UAR UAR UAR UAR UAR -y^" ^'^^


6-64

la c

BT97M195

6-65

580 Super L Series 2 Loader Backhoe R E A R DRIVE A X L E DIFFERENTIAL LOCK REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14

PART NO. 279169A1 29^213A1 305152A1 292210A1 292212A1 •800-5120 292214A1 292902A1 175966A1 175964A2 175965A1 128376A1 175968A1 614-8030 814-8080

Bur 7-3350

DESCRIPTION AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 CYLINDER - differential lock . 0-RING - cylinder. O-RING - seal, external, piston PISTON - differential lock RING - external heavy retaining. No. 20 . SHAFT - rail, shifter fork BUSHING - shaft SPRING -shaft. . FORK - shift BUSHING - rail O-RING - cover •• COVER - housing BOLT - hex, full threads, 8 - 1 . 2 5 x 30 mm BOLT - hex, 8 - 1 . 2 5 x 80 mm ,

REQ'D. 1 1 .1 .2 • -I • 1 1 .....2 1 "> 1 1 2 .2


6-66

V)J

(22)

^

BT97N056

/

(22)

C24

580 Super L Series 2 Loader Backhoe REAR DRIVE A X L E PLANETARY REF. 1 2 2 3 4 5 6 7 7A 8 9 10

PART NO. 279169A1 175974A1 D142986 196090A1 P2930467 175976A1 292891A1 . NSS 100557A1 238-6121 K395082 K395093 ' 292893A1

11 12 13 14 15 17 18 19 20

292894A1 292898A1 247550A1 175982A1 K395131 107071A1 295580A1 175984A1 NSS

21 22 23 24 25 26 27 28 29

196065A1 196066A1 292896A1 247877A1 K395101 800-2136 292900A1 292899A1 292901A1

Bur 7-3350

6-67

DESCRIPTION REQ'D. AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 1 HUB ASSEMBLY - wheel attaching .-. 2 STUD - special, without flanged collar 20 STUD - special, with collar, for recessed bolt holes, if used 20 O-RING -sealing 2 GEAR - ring, planetary 2 : CARRIER ASSEMBLY - planetary. 2 SHAFT - pinion gear 6 PLUG -drain 2 O-RING - 1 - 1 / 1 6 ID X 3/32 inch wide, not shown . 1 SCREW - special, planetary cover plate 4 PIN - locking, planetary carrier 2 BEARING - needle (package of 10 needles) (372 needles required) planetary gear 38 GEAR - pinion, planetary 6 WASHER - thrust, pinion gear 6 BEARING - needle (package of 10 used as pins)(6 required) 1 BOLT - hex, self-locking, special, 1 0 - 1.25 x 50 mm, class 10.9 6 BOLT - hex head, special, 1 4 - 1.50 x 65 mm, self-locking 16 BUSHING - centering, 20 mm OD .16 HUB - ring gear 2 RING-lock .....2 COUPLING - drive, welded to and included with the differential brake oil auger • -2 BUSHING - axle housing, drive . .2 SEAL - oil, axle housing • .2 SHAFT - drive 2 SEAL - oil, cassette, replaces 1349265C1 seal 2 BEARING - ball, hub 4 RING - internal retaining. No. 36 2 WASHER - thrust, pinion gear, outer 6 WASHER - thrust, pinion gear, inner 6 WASHER - needle bearing s . 6


6-68

BT97M009

6-69

580 Super L Series 2 Loader Backhoe DRIVE SHAFT FOR R E A R DRIVE A X L E REAR DRIVE AXLE TO TRANSMISSION REF.

9 10 11 12

PART NO. 284712A1 144278A1 NSS NSS NSS 219-10 NSS 144279A1 219-10 D149860 NSS NSS NSS 90-6682T1

13

D137627

2 3 4 5 6 7 . 8

Bur 7-3350

DESCRIPTION SHAFT ASSEMBLY - drive \ KIT - universal joint JOINT - universal, drive shaft BEARING - universal joint. • RING - retaining FITTING - grease, straight, 1/4-28 taper x 1 1 / 1 6 inch SHAFT - drive, transmission to rear axle YOKE - tube, splined, to rear axle FITTING - grease, straight, 1/4-28 taper x 11/16 inch K I T - d u s t cap. WASHER-cork WASHER-steel CAP - dust seal retaihing RETAINER - drive shaft, strap, not included in drive shaft assembly, purchase separately BOLT - special

REQ'D. .1 2 1 4 4 , .2 :1 -I . .1 -I • • -1 -1 1 2 4


6-70


7^1

A L P H A B E T I C A L INDEX BRAKES DESCRIPTION Differential Brake - Rear Axle Hydraulic Circuit Master Cylinder Master Cylinder Mounting Parking Brake - Rear Axle Parking Brake Lever and Linkage Pedals

Bur 7-3350

PAGE ...7-3 7-9 7-11 7-7 7-5 7-13 7-7


7-2

a

7-3

580 Super L Series 2 Loader Backhoe REAR DRIVE A X L E DIFFERENTIAL BRAKE REF,. 1 2 3 4 5 6 7

PART NO, 279169A1 * 237021A1 *237022A1 *237023A1 864-8016 190461A1 190460A1 +190449A1

8

+295032A1

9 10 11 12 13 14 15 16 17 18 19 20 21

190450A1 814-6035 *237026A1 190492A1 190502A1 190493A1 190447A1 *237024A1 190453A1 295111A1 .864-6035 190500A1 *237025A1 190504A1 295112A1

22 23

i

i

24

295113A1

25

863-6020

+248071A1

^243893A1

Bur 7-3350

DESCRIPTION -AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 DISC - brake. PLATE - friction, inner PLATE - piston BOLT - hex socket, 8 - 1.25 x 16 mm. FLANGE - inner FLANGE-outer SPACER - split, 18 X 20 mm, no longer sold separately, order 248071A1 kit below BUSHING - spacer, no longer sold separately, order 248071A1 kit below WASHER - flat, special B O L T - h e x , 6 - 1 . 0 x 3 5 mm SPRING-outer O-RING-small PISTON - brake ; O-RING-large PIN - split, 6 x 14 m m . PLATE - friction, outer SLEEVE -splined SHAFT - splined BOLT - hex socket, 6 - 1 . 0 x 35 mm COVER - spring SPRING - inner GASKET - piston AUGER - oil, right-hand, includes weld-on clamp and bolt, also includes welded on drive coupling AUGER - oil, left-hand, includes weld-oh clamp and bolt, also includes welded on drive coupling, not shown BOLT - hex socket, 6 - 1 . 0 x 20 mm, class 12.9, not shown, right-hand or left-hand auger

REQ'D. 4 -2 2 18 2 2 . .6 12 6 6 6 2 .2 • .2 .6 2 2 .2 6 6 . .6 2 1 :1 2

KIT - brake self adjuster, includes spacer and bushing, plus an instruction sheet.. :

1

KIT - brake disc and plates, service replacement, includes above items marked with an asterisk

1


r-4

580 Super L Series 2 Loader Baclchoe REAR DRIVE A X L E PARKING BRAKE REF. 1 2 3 4 4 5 6 7 8 9 12 13 14 17 18 19 20 21 22 23

'

PART NO. 279169A1 190451A1 190463A1 280436A1 190476A2 190477A2 256483A1 283462A1 E l 35810 190473A1 190456A1 190448A1 256478A1 256481A1 256482A1 256485A1 283466A1 281952A1 280450A1 280452A1 280457A1 281960A1

Bur 7-3350

7-5

DESCRIPTION REQ'D. AXLE ASSEMBLY - rear drive, parts list pages 6-59 - 6-67, 7-3 and 7-5 . . . . . . . 1 BOLT - special, 8 x 20 m m . 6 WASHER-flat 2 LEVER-brake, 100mm 2 SPRING - left-hand, shown 1 SPRING - right-hand, not shown 1 SHAFT - brake control 2 BOLT - special, 8 - 1 . 0 x 23.5 mm 2 PLUG - brake bleeder, brake housing • -2 SPRING-cam 2 CAM - brake 2 O-RING - special 2 BRACKET-stop . • • .2. BUSHING - shaft : • • -2 S H I M - shaft 2 B O L T - special, 6 X 16 m m . . 2 BALL - 6.5 mm 2 KIT - switch, park brake 2 SWITCH-brake 1 BRACKET - switch guard, lever 1 SLEEVE - switch 1 NUT - special, 16 mm - 1 . 5 1


7-6

&

BT97M199

(30


7-7

B R A K E P E D A L S AND B R A K E MASTER CYLINDER MOUNTING REF. 1 2 3 5 6 7 8 9 10 11 12 13 14 15 17 19 20

PART NO. 182445A1 614-8030 892-11008 425-156 D137077 L26209 432-612 D140035 614-10025 892-11010 829-1410 .D124529 A77310 814-8040 832-10408 D124528 121-145

21 23 24 26

425-105 D124530 438-12040 230973A1

27

614-8045

28 30 31

829-1408 495-81261 D148108

32 33 34

,A187990 / 234623A1 234622A1

Bur 7-3350

DESCRIPTION • CYLINDER ASSEMBLY - brake master, parts list page 7-11 . BOLT - hex, full threads, 8 - 1.25 x 30 mm WASHER - lock, 8 mm NUT - hex, jam, 3/8 inch NF CLEVIS - female, master c y l i n d e r . . . ; . PIN - clevis, 3/8 inch PIN - cotter, 3/32 x.3/4 inch S H A F T - b r a k e pedaL B O L T - h e x , full threads, 10 - 1 . 5 x 25 mm WASHER - lock, 10 mm NUT - hex, 10 mrii - 1 . 5 , class 1 0 . 9 . . . . SPACER - brake shaft, pedal BEARING - pivot, foot pedal BOLT - hex, 8 - 1.25 x 40 mrh NUT - hex, self-locking, 8 mm - 1 . 2 5 L E V E R - b r a k e lamp BOLT - flat countersunk head, 5/16 NC x 2-1/2 inch, special, brake switch actuator NUT - hex, 5/16 inch NC P I N - p e d a l lock P I N - r o i l , 5 / 1 6 x 2 - 1 / 2 inch SPRING - pedal and lever return, attaches to brake pedal spring rod in firewall frame : BOLT - hex, full threads, 8 - 1.25 x 45 mm, attaches to brake pedal stop bar in firewall frame NUT - hex, 8 mm - 1 . 2 5 , class 10 WASHER - flat, 1 3 / 1 6 x 1 - 1 / 2 x 1 / 1 6 inch, use as a shim SWITCH - rocker, brake lamp, attaches to front console wiring harness, mounts in brake pedal stop bar in firewall frame tERMINAL-male PEDAL - brake, right-hand PEDAL - brake, left-hand

REQ'D. 2 4 • . -4 .2 2 .2 2 1 1 1 1 2 4 4 4 1 • •'I 1 • •-1 1 .3 2 '4 UAR ••-I 2 1 . .1


7-8

0

(T9A)—

BT97MK«


7-9

B R A K E MASTER CYLINDER HYDRAULIC CIRCUIT REF. 1 2 3 A 5 6 7 8 9

PART NO, 182445A1 D136430 142003A1 121730A2 614-8030 892-11008 829-1408 121729A1 296171A1

10 11

214-1704 214-1706

12 13 14

515-22127 1976943C1 131676A1

15 16 17 18 18

515-23127 276743A1 276746A1 142007A1 247570A1

19 19A 20 21 22 23

218-5053 237-6004 895-11008 614-8016 D132982 L I 8337

Bur 7-3350

DESCRIPTION CYLINDER ASSEMBLY - brake master, parts list page 7 - 1 1 . . . . TUBE - crossover TUBE - reservoir to master cylinder BRACKET - brake reservoir support, attaches to firewall BOLT - hex, full threads, 8 - 1.25 x 30 mm WASHER - lock, 8 mm NUT - hex, 8 mm - 1 . 2 5 , class 10 HOSE - 50 mm (2 inch) long, reservoir to master cylinder HOSE - 1 2 2 5 mm (48-1/4 inch) long, reservoir outlet, attaches to return to tank tube, item 22 on page 8-9 CLAMP - adj, 1/4 - 5/8 inch dia . . . . . . . . . . CLAMP - adj, 7/16 - 3/4 inch dia, worm screw, attaches to, return to tank tube : [. CLAMP - P-type, 1/2 inch ID RESERVOIR - brake master cylinder HOSE - 1590 mm (62-5/8 inch) long, reservoir inlet, attaches to tee at hydraulic oil filter, item 9 on page 8-9 CLAMP - P-type, 1/2 inch ID T U B E - brake, left-hand TUBE - brake, right-hand HOSE - 625 mm (24-5/8 inch) long, brake tube to adapter on rear axle HOSE - 430 mm (16-15/16 inch) long, brake tube to adapter on rear axle, used in production, for service order 142007A1 hose. . . . : ADAPTER - straight, 7/16-20 flare x 0-ring boss 0-RING - 23/64 ID x 5/64 inch wide.WASHER - flat, 9 x 17 x 1.6 mm BOLT - hex, full threads, 8 - 1.25 x 16 mm SLEEVE - hose guard STRAP - tie, 15 inch, if used

REQ'D. 2 1 2 1 6 8 1 2 1 5 2 2 1 .1 7 1 .1 2 2 .2 1 ,1 2 1 .1


7-10

870052S


7-11

BRAKE MASTER CYLINDER REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

PART NO. 182445A1 NSS * NSS * NSS NSS NSS NSS NSS NSS *NSS NSS *NSS NSS * NSS * NSS * NSS NSS *NSS NSS

DESCRIPTION CYLINDER ASSEMBLY - brake master BODY - master cylinder SEAL - plunger WASHER - special ' SEAT - spring, short PLUNGER - piston SPRING - return. SEAT - spring, long PISTON - master cylinder SEAL - piston WASHER - seal, special RING - retaining, washer ROD - push BOOT - push rod BALL - flow valve SEAL - flow valve VALVE-flow. GASKET-flow valve ADAPTER - flow valve

'N14784

KIT - seal, cylinder, service, includes all items marked with an asterisk

Bur 7-3350

REQ'D^ 2

1


7-12

0

9, @

BS97M201


7-13

PARKING BRAKE LEVER AND LINKAGE REF.

PART NO. 279261A1

1 2 3 4 5 6 7' 8 9 10 10A 11 . 12 13 . 14 15 16 17 18 19 20 21 22 23 24 25 26 " 27 28 29

NSS D42458 432-612 495-21038 124646A1 614-10025 892-11010 829-1410 280681A1 827-8050 827-8060 . D150633 D121608 D129747 892-11008 829-1408 280886A1 425-156 432-612 L11182 D149288 829-1410 892-11010 A188028 614-10025 180801A1 '495-11041 425-106 LI 8337 223722A1

30 31 32

814-10060 895-11010 130245A1

Bur 7-3350

DESCRIPTION LEVER ASSEMBLY - parking brake, with bossed hole for brake switch, 18-5/8 (474 mm) long LEVER - 279261A1 parking brake PIN - clevis, lever to brake cable PIN - cotter, 3/32 x 3/4 inch WASHER- flat, 3/8 x 7/8 x, 3/32 inch BRACKET - mounting, parking brake lever BOLT - hex, full threads, 10-1.5 x 25 mm WASHER-lock, 10 mm NUT-hex, 10 mm-1.5, class 10.9. CABLE - parking brake, 1325 mm (52-3/16 inch) long BOLT - hex, 8 - 1.25 x 50 mm, class 10.9 BOLT - hex, 8 - 1.25 x 60 mm, class 10.9 SPACER - split, damp CLAMP-cable. PLATE - oval spacer,' plated WASHER - lock, 8 mm NUT-hex, 8 mm-1:25, class 10 , YOKE - cable, 110 mm (4-3/8 inch) long NUT - hex, jam, 3/8 inch NF PIN - cotter,-3/32 x 3/4 inch CLEVIS - offset, 3/8 inch PIN - clevis : NUT-hex, 10 mm-1.5, class 10.9 WASHER-lock, 10mm CLAMP-cable. BOLT-hex, full threads, 10- 1.5x25 mm BRACE - loader control bracket WASHER - flat, 13/32 x 13/16 x 1/16 inch. NUT - hex, 3/8 inch NC STRAP - tie, 15 inch, if used BRACKET - combination, yield support, brake cable, mounts with P-clamp (Ref 26, page 4-11) to chassis frame • . .|. BOLT - hex, 10 - 1.5 x 60 mm WASHER - flat, 11 x 20 x 2 mm SPACER - bracket

REQ'D. 1 1 1 1 1 1 2 2 2 1 1 1 2 1 1 -2 2 1 1 • 2 1 2 2 2 1 .2 1 6 6 1 1 1 1 1



8-1

ALPHABETICAL INDEX HYDRAULICS

DESCRIPTION

PAGE

Accumulator Assembly - Ride Control Gylinders Boom - Backhoe Bucket - Backhoe Bucket - Loader Clam-Loader Dipper- Backhoe , Dipper Extension - Backhoe Lift-Loader : Stabilizer - Backhoe Swing - Backhoe Equipment Hydraulic System Equipment Pump and Loader Valve to Backhoe Valve Oil Cooler Lines, Return Lines, and Filter Reservoir to Loader Valve and Loader Valve to Filter Filter - Hydraulic Oil Hydraulic Circuits Auxiliary Backhoe.. Hand Held. Boom Cylinder - Backhoe Boom Lock Bucket Cylinder - Backhoe, With Extendable Dipper Bucket Cylinder - Backhoe, Without Extendable Dipper.. Bucket Cylinder - Loader.. Clam Cylinder - Loader , Dipper Cylinder-Backhoe Extendable Dipper - Backhoe Lift Cylinder - Loader..... Loader Valve to Backhoe Valve - Without Auxiliary Hydraulics and With or Without Extendahoe Quick Coupler - Loader Hydraiulic Tool... Ride Control Stabilizer Cylinder - Backhoe Swing Cylinder - Backhoe Pump - Equipment Valves Auxiliary Backhoe Control Boom Lock Solenoid Loader Control

8-123

Bur 7-3350

8-137 8-141 8-129 8-131 8-139 8-143 8-127 8-133 8-135 8-7 8-9 8-3,8-5 8-125 8-51-8-55 8-41-8-49 8-25 8-57;8-59 8-33,8-35 8-29,8-31 8-13,8-15 8-17,8-19 8-27 8-37 8-11

i

8-39 8-65 - 8-69 8-61,8-63 8-21 8-23 8-71

^1

8-117,8-119 8-89 - 8-115 8-121 8-73 - 8-87

1 Issued February, 1998

8-2

BT97N188

8-3


EQUIPMENT HYDRAULIC SYSTEM

RESERVOIR TO LOADER CONTROL VALVE AND LOADER VALVE TO FILTER FIEF. 1 2 3 . 4 5 6

PART NO. 259044A1 282497A1 131586A1 282496A1 121817A1 218-5137

7 8 9 10 11

237-6010. A14141 614-12035 238-5228 257954A1

12 13 14 15 16 17 18 19 20 r

257948A1 NSS N14330 413-728 492-11044 A30013 218-5077 237-6016 144215A1 21.8-587,

21 22 23 24 25 26 27

D137625 NSS 425-1120 NSS NSS NSS H434163 122125A1

28 29 30

115507A1 D67297 REF

DESCRIPTION REQ'D. CLAMP-tube 4 HOSE - suction, at hydraulic tank 1 TUBE - suction 1 HOSE-coupler 1 TUBE - suction, at hydraulic equipment pump 1 ELBOW - 45 degree, 7/8-14 inch flare x adj 0-ring boss, to cooler return hose -1 0-RING - 3/4 ID X 3/32 inch wide. :1 FLANGE - split, 2 inch 2 BOLT - hex, full threads, 12 - 1.75 x 35 mm 8 0-RING - 2-1/4 ID X 1/8 inch wide. 1 PUMP ASSEMBLY - hydraulic equipment, with 17 teeth shaft gear set, parts list page 8-71 1 COUPLING - flex, 17 teeth, with steefplug 1 COUPLING - pump . 1 BUSHING - coupling 4 BOLT - hex, 7/16 NC x 1-3/4 inch 4 WASHER - lock, 7/16 inch 4 WASHER - special, hardened . . . . . . 4 ADAPTER - straight, 1-1/16-12 flare x 1-5/16-12 inch O-ring boss .1 O-RING- 1-11/64 ID X 7/64 inch wide 1 HOSE - 576 mm (22-11/16 inch) long, large pump section port .1 TEE -1-1/16-12 flare branch x 1-5/16-12 inch flare x flare, pump outlet hose to loader valve inlet tube .1 COUPLING - quick disconnect 1 BODY - coupling 1 NUT-hex, 1-1/4 inch N F . . . 1 SEAT - spring 1 SPRING - coupling. 1 POPPET - coupling 1 CAP - dust, coupler 1 TUBE - tee to loader control valve inlet, see page 8-13 items 19-23 for tube clamps near loader valve, used with Ref 34 adapter, used without loader hydraulic tool quick coupler . 1 PLATE - mounting .1 INSULATOR - rubber, tube .1 INSULATOR - tube, small pump section tube to backhoe valve, see page 8-7, items 4 and 5, for tube and insulator 1 Continued on next page

Bur 7.3350.


8-4

BT97N188

8-5



RESERVOIR TO LOADER CONTROL VALVE AND LOADER VALVE TO FILTER REF. 31 32 33 34

PART NO. R46493 D143422 814-10050 218-5069

35 36

237-6016 144227A1

37

218-5245

38 39

237-6016 LI 8337

Bur 7-3350

DESCRIPTION SPACER - split, 22 mm (7/8 inch) long CLAMP- double tube BOLT-hex, 10- 1.5x50 mm ADAPTER - straight, 1-5/16-12 inch flare x 0-ring boss, at loader valve inlet and outlet ports, adapter at upper port is replaced by a tee on models with loader hydraulic tool quick coupler, see page 8-65, Ref 10 O-RING -1-11/64 ID X 7/64 inch wide . HOSE - 520 mm (20-15/32 inch) long, loader valve to filter, models without ride control, see page 8-61 for parts used on models with ride control TEE -1-5/16-12 inch flare branch x flare x adj 0-ring boss, loader valve to filter and filter to backhoe control valve 0-RING - 1 -11/64 ID X 7/64 inch wide STRAP - tie, 15 inch, if used

REQ'D. 1 1 1 2 1 1 1 1 .1


8-6

< : £ . > - ^ > W ^ r k ^ (i6A^ 3 Â

8-7



EQUIPIVIENT PUIVIP AND LOADER CONTROL VALVE TO BACKHOE CONTROL VALVE REF. 1

PART NO. 218-5063

2 3 4 5

237-6012 144216A1 122127A1 D143797

6 7 7A 7B 8 9 10 11 12 13 14 15 16

218-736 243790A1 218-5062 237-6010 115633A1 D143797 D143411 614-10025 218-5062 237-6010 218-5069 237-6016 144240A1

16A

144241A1

17 18 19 27 29 30

136008A1 614-12030 829-1412 144477A1 829-1410 144479A1

Bur 7-3350

DESCRIPTION REQ'D. ADAPTER - straight, 7/8-14 flare x 1-1/16-12 inch O-ring boss, small pump section outlet port O-RING - 59/64 ID x 7/64 inch wide HOSE - 800 mm (31-1/2 inch) long, small pump section outlet p o r t . . . . TUBE - small pump section hose to backhoe INSULATOR - 5/8 inch, small pump section tube, see page 8-3 and 8-5 items 28 - 33 for hardware CONNECTOR - straight, 7/8-14 inch flare. TUBE - swing supply, small pump tube to swing section in|et ADAPTER - straight, 7/8-14 inch flare x O-ring boss. O-RING - 3/4 ID X 3/32 inch wide. . PLATE - mounting INSULATOR - 5/8 inch, tube mounting CLAMP - P-type, 3/4 inch ID, tube BOLT - hex, full threads, 10 -1.5 x 25 mm , .2 ADAPTER - straight, 7/8-14 inch flare x O-ring boss. O-RING - 3/4 ID X 3/32 inch wide ADAPTER - straight, 1-5/16-12 inch flare X O-ring boss O-RING - 1-11/64 ID X 7/64 inch wide HOSE - 1028 mm (40-1/2 inch) long, loader valve power beyond port to backhoe control valve inlet, models with two spool loader control valve.. HOSE - 977 mm (38-15/32 inch) long, loader valve power beyond port to backhoe control valve inlet, models with three spool loader control valve .1 BRACKET - mounting, hose 1 BOLT - hex, full threads, 12 - 1.75 x 30 mm 1 NUT - hex, 12 mm -1.75, class 10 .1 INSULATOR - rubber, power beyond hose.; 1 NUT - hex, 10 mm -1^5, class 10.9. 1 CLAMP - isolation, if used 1


8-8

J23)


8-9

EQUIPMENT HYDRAULie SYSTEM OIL COOLER LINES, RETURN LINES, AND FILTER REF. PART NO. 1 122536A1 2 614-10020 3 . • 895-1,1010 4 218-5245 5 6 7

237-6016 144233A1 218-5069

7A

218-5245

8 9 10 11 12 13

237-6016 228959A1 237-6010 i,122176A1 144220A1 291288A1

14 15 16 17 1819 20 21 22 23

236231A1 218-5137 237-6010 •115633A1 D143430 614-10025 218-5086 237-6020 295172A1 D38435

24

214-1420

DESCRIPTION REQ'D. FILTER ASSEMBLY - hydraulic oil, parts list page 8-125 1 BOLT - hex, full threads, 10 -1.5 x 20 mm 4 WASHER - flat, 11 x 20 x 2 mm .4 TEE -1-5/16-12 inch flare branch x flare x adj 0-ring boss, loader valve to filter and filter to backhoe control valve 1 0-RING -1-11/64 ID X 7/64 inch wide 1 HOSE - 890 mm (35 inch) long, return, backhoe control valve to filter 1 ADAPTER - straight, 1 -5/16-12 inch flare x O-ring boss, backhoe control valve outlet port, models without extendable dipper .1 TEE -1-5/16-12 inch flare branch x flare x adj 0-ring boss, backhoe control valve outlet port, models with extendable dipper, if used 1 O-RING - 1-11/64 ID X 7/64 inch wide, 218-5069 or 218-5245 fitting 1 TEE - special 1 0-RING - 3/4 ID X 3/32 inch wide 1 TUBE - filter to cooler 1 HOSE - 595 mm (23-7/16 inch) long, filter to cooler . . . . : 1 COOLER - hydraulic oil, heavy duty, see page 6-21 for cooler mounting hardware 1 HOSE - 300 mm (11-13/16 inch) long 1 ELBOW - 45 degree, 7/8-14 inch flare x adj 0-ring boss 1 O-RING - 3/4 ID x 3/32 inch wide 1 PLATE - mounting 2 CLAMP-tube 2 BOLT - hex, full threads, 10 -1.5 x 25 mm 2 ADAPTER - straight, 1-5/16-12 flare x 1-5/8 inch O-ring. 1 O-RING -1-15/32 ID x 1/8 inch wide .1 TUBE - return to tank 1 HOSE - 89 mm (3-1/2 inch) long, cut from SI 18383X bulk hose, return tube to tank, see page 7-9 for attaching brake line clamp 1 CLAMP - adj, 13/16 -1-3/4 inch dia .2

S118383X

HOSE - bulk, 25(1) X 38 (1-1/2) X 4877 mm (192 inch) long

Bur 7-3350

1


8-10


8-11

LOADER LIFT CYLINDER HYDRAULIC CIRCUIT REF. 1

PART NO REF

23 4

218-5241 237-6010 225330A1

5

231984A1

6

225332A1

7

231982A1

8 9 10 11 12 13 14 15

D138055 814-10040 120303A1 896-11010 892-11010 829-1410 187535A1 187536A1

16 17 18

218- 5107 237-6010 112366A2

19 20 21 22 24 28 29 30

219- 55 D142787 214-1472 218-435 221162A1 221158A1 232929A1 232939A1

31

232941A1

32

232931A1

DESCRIPTION REQ'D. VALVE ASSEMBLY - loader control, for correct assembly and components, see page 8-73 or 8-75 1 TEE - 7/8-14 inch flare branch x flare x adj O-ring boss . . .2 0-RING - 3/4 ID X 3/32 inch wide .1 TUBE - upper lift port to left-hand loader lift cylinder rod end, used in production (services; itself, for service order 225330A1 tube, Ref 4A), models without ride control, see page 8-61 for parts used on models with ride control 1 TUBE - lower lift port to right-hand loader lift cylinder closed end, used in production (for service order 221158A1 and 232929A1 tubes and 218-435 connector, Ref 22, 28 and 2 9 ) . . . . . . .1 TUBE - lower lift port to jeft-hand loader lift cylinder closed end, used in production (for service order 232939A1 and 232941A1 tubes and 218-435 connector, Ref 22, 30 and 31), models without ride control, see page 8-61 for parts used on models with ride control 1 TUBE - upper lift port to right-hand loader lift cylinder rod end, used in production (for service order 221162A1 and 232931A1 tubes and 218-435 connector, Ref 22, 24 and 32) 1 CLAMP-tube 4 BOLT-hex, 10- 1.5x40 mm 3 SPACER - tube 3 WASHER - flat, 11 x 21 x 2.5 mm, hardened 1 WASHER-lock, 10 mm 3 NUT - hex, 10 mm -1.5, class 10.9. . . . . . . . . . . .3 ' HOSE - 720 mm (28-11/32 inch) long, lift cylinder closed end 2 HQSE - 1090 rrim (43 inch) long, upper port of control valve to lift cylinder rod end 2 ELBOW - 90 degree, 7/8-14 inch flare x adj O-ring boss 4 0-RlNG - 3/4 ID X 3/32 inch wide. 1 CYLINDER ASSEMBLY - 83 (3-1/4) ID x 766 mm (30-1/8 inch) stroke, loader lift, parts list page 8-127 2 FITTING - grease, 90 degree, 1/8 PT x 27/32 inch 2 INSULATOR - rubber 2 CLAMP - adj, 4-1/16 - 5 inch dia . . . . . 2 CONNECTOR - straight, large hex, 7/8-14 inch flare 1-3 TUBE - right-hand loader lift cylinder rod end 1 TUBE - right-hand loader lift cylinder closed end 1 TUBE - lower lift port to right-hand loader lift cylinder 1 TUBE - lower lift port to left-hand loader lift cylinder, models without ride control, see page 8-61 for parts used on models with ride control 1 TUBE - left-hand loader lift cylinder closed end, models without ride control, see page 8-61 for parts used on models with ride control 1 TUBE - upper lift port to right-hand loader lift cylinder 1

NOTE: See pages 3-3 and 9-79 for hydraulic tubing covers above fuel and hydraulic oil reservoirs.

Bur 7-3350


8-12

BT97N186


8-13

LOADER B U C K E T CYLINDER HYDRAULIG CIRCUIT REF. 1

PART NO. REF

2 3 4

218-5062 237-6010 232447A1

220169A1

6 7 8 9 10 11 12 13

D138055 814-10040 120303A1 896-11010 892-11010 829-1410 138467A1 196817A1

14

196819A1

15 16 17 18

D138055 892-11010 829-1410 218-5220 *

19

221733A1

20 21 22 23 24

814-10040 120303A1 892-11010 829-1410 196815A1

25

196813A1

26

136226A1

DESCRIPTION REQ'D. VALVE ASSEMBLY - loader control, for correct assembly and components, see page 8-73 or 8-75, for mounting see page 9-3 1 ADAPTER - straight, 7/8-14 inch flare x O-ring boss. . . .i 2 O-RING - 3/4 ID x 3/32 inch wide 1 TUBE - bucket section upper port, used in production (for service order 232934A1 and 232936A1 tubes and 218-435 connector, Ref 4 1 , 46 and 47 on page 8-15) 1 TUBE - bucket section lower port, used in production, replaces 192136A1 production tube (for service order 221143A1 and221146A1 tubes and 218-435 connector, Ref 4 1 , 44 and 45 on page 8-15) 1 CLAMP - tube 3 B O L T - h e x , 1 0 - 1 . 5 x 4 0 mm 2 SPACER - tube . .2 WASHER - flat, 1 1 x 2 1 x 2 . 5 mm, hardened .2 . W A S H E R - lock, 10 mm . . . . . . .2 NUT - hex, 10 mm - 1.5, class 10.9 .2 HOSE - 680 mm (26-3/4 inch) long, at loader arm pivot 2 TUBE - lower, on right-hand lift arm, from bucket section upper port to closed end of bucket cyinders 1 TUBE - upper, on right-hand lift arm, frorn bucket section lower port to bucket cyinder rod end . 1 CLAMP - tube . 3 W A S H E R - l o c k , 10 mm 3 , NUT - hex, 10 mm - 1 . 5 , class 10:9. .3 TEE - swivel, 7/8-14 inch flare; branch x flare x swivel, at upper lift frame crossover tube 2 , CLAMP - tube, attaches to item 5 tube above and item 27 tube on page 8-3 2 B O L T - h e x , 1 0 - 1 . 5 x 4 0 mm 2 SPACER - tube 2 W A S H E R - l o c k , 10 mm ..2 N U T - h e x , 10 mm - 1.5, class 10:9 .2 TUBE - crossover, rear, upper lift frame tube to rod end of bucket cylinder .1 TUBE - crossover, front, lower lift frame tube to bucket cylinder closed end .1 HOSE - 840 mm (33.inch) long, at bucket cylinders .4

NOTE: See pages 3-3 and 9-79 for hydraulic tubing covers above fuel and hydraulic oil resen/oirs. Continued on next page

Bur 7-3350


8-14

(22)

BT97N186

(23)


8-15

LOADER B U C K E T CYLINDER HYDRAULIC CIRCUIT REF. 27 28 29 30 31/ 32 33 34

PART NO. 192152A1 218-5062 237-6010 192156A1 192154A1 218-5107 237-6010 113133A2

35 36 37 38 39 .40 41 44 45 46 47

250648A1 814-10040 892-11010 895-11010 L79937 214-1464 218-435 221143A1 221146A1 232934A1 232936A1

DESCRIPTION TUBE - bucket cylinder rod end ADAPTER - straight, 7/8-14 inch flare x O-ring boss O-RING - 3/4 ID x 3/32 inch wide TUBE - right-hand bucket cylinder closed end TUBE - left-hand bucket cylinder closed end ELBOW - 90 degree, 7/8-14 inch flare x adj O-ring boss O-RING - 3/4 ID x 3/32 inch wide CYLINDER ASSEMBLY - 76 (3) ID x 522 mm (20-9/16 inch) stroke, loader bucket, parts list page 8-129 GUARD - crossover tube B O L T - hex, 1 0 - 1 . 5 x 4 0 mm W A S H E R - l o c k , 10 mm WASHER - flat, 11 X 20 X 2 mm SPACER - rubber, tube C L A M P - a d j , 3-9/16-4-1/2 inch dia CONNECTOR - straight, large hex, 7/8-14 inch flare TUBE - bucket section lower port at valve. TUBE - bucket section lower port tube to hose TUBE - bucket section upper port at valve TUBE - bucket section upper port tube to hose

REQ'D. 2 2 1 1 1 2 1 2. .1 2 2 2 2 2 1-2 1 1 .1 1

NOTE: See pages 3-3 and 9-79 for hydraulic tubing covers above fuel and hydraulic oil reservoirs.

Bur 7-3350


8-16

BT97N048


8-17

LOADER GLAM CYLINDER HYDRAULIC CIRCUIT REF. 1

PART NO. 302966A1

2 3 4

218-5062 237-6010 225326A1 225328A1

6 7 8 9 10 11 12 13 14 16 17

814-10040 D138055 120303A1 892-11010 829-1410 138467A1 196824A1 196821A1 D138055 829-1410 892-11010 218-776

18 19 20 21

188058A1 232945A1 218-435 232947A1

is;

DESCRIPTION REQ'D. VALVE ASSEMBLY - loader control, three-spool, parts list page 8-75, for mounting hardware see page 9-3 1 ADAPTER - straight, 7/8-14 inch flare x O-ring boss 2 O-RING - 3/4 ID X 3/32 inch wide .1 TUBE - upper port loader valve clam section to hose at loader arm pivot (services itself). 1 TUBE - lower port loader valve clam sectiorfto hose at loader arm pivot, used in production (for service order 232945A1 and 232947A1 tubes and 218-435 connector, Ref 19-21) 1 BOLT - hex, 10 - 1 . 5 x 40 mm, mm 2 CLAMP-tube. : -2 SPACER-tube 2 WASHER - lock, 10 mm . . . . ! .2 NUT - hex, 10 mm - 1 . 5 , class 10.9. 2 HOSE - 680 mm (26-3/4 inch) long, at loader arm pivot 2 TUBE - lower, on loader lift frame, port A 1 TUBE - upper, on loader lift frame, port B 1 CLAMP - tube 4 NUT - hex, 10 mm - 1 . 5 , class 10.9 4 WASHER - lock, 10 mm . . . . 4 PLUG - hex, 7/8-14 inch flare, not used on models with clam bucket, if used ' 2 RESTRICTOR - check 1 TUBE - lower port at loader valve 1 CONNECTOR - straight, large hex, 7/8-14 inch flare 1 T U B E - lower port at loader valve 1

NOTE: See pages 3-3 and 9-79 for hydraulic tubing-covers above fuel and hydraulic oil reservoirs.

Bur 7-3350


8-18


8-19

LOADER CLAM CYLINDER HYDRAULIC CIRCUIT AT LOADER B U C K E T REF. 1

PART NO. 1346190C1 1346189C1

3 4 5 6 7 8 9 10

192352A1 192345A1 144242A1. D40236 R46493 814-10040 892r11010 218-1237

11 12 13 14 15 16

218-1251 144243A1 515-25254 895-11010 832-10410 218-5137

17 18

237-6010 218-5107

19 20 21/

237-6010 D38648 214-1464

DESCRIPTION REQ'D. CYLINDER ASSEMBLY - 76 (3) ID x=231 mm (9 inch) stroke, clam, left-hand, parts list page 8-131 1 CYLINDER ASSEMBLY - 76 (3) ID x 231 mm (9 inch) stroke, clam, right-hand, parts list page 8-131 1 TUBE - left-hand cylinder 1 TUBE - rightjhand cylinder 1 HOSE - 1 1 2 0 mm (44-3/32 inch) long, right-hand and left-hand cylinders 4 CLAMP - horizontal hose 2 SPACER - split, 22 mm (7/8 inch) long 2 BOLT - hex, jl 0 - 1 . 5 x 40 mm 2 WASHER - lock, .10 mm 2 TEE - 7/8-14] inch flare branch x flare x bulkhead flare, connecting horizontal and vertical tubes and hoses 2 NUT - hex, lock, bulkhead, 7/8 inch NF 2 HOSE - 1 1 6 7 mm (46 inch) long, lift arms 2 CLAMP - P-type, 1 inch ID, vertical hoses 2 WASHER - flat, 11 x 20 x 2 mm 1 NUT - hex, self-locking, 10 mm - 1 . 5 1 ELBOW - 45 degree, 7/8-14 inch flare x adj 0-ring boss, clam cylinders, rod end 2 O-RING - 3/4 ID x 3/32 inch wide 1 ELBOW - 90 degree, 7/8-14 inch flare x adj O-ring boss, clam cylinders, closed end 2 O-RING - 3/4 ID x 3/32 inch wide 1 SPACER - rubber, clamp .2 CLAMP - adj, 3-9/16 - 4-1/2 inch dia, clam cylinder tubing 2

NOTE: To complete the clam cylinder hydraulic circuit see page 8-17.

Bur 7-3350


8-20

rX2l)

(201

(27)^

BT97N182

(35)

(36


8-21

B A C K H O E S T A B I L I Z E R CYLINDER HYDRAULIC CIRCUIT REF. 1

PART NO. REF

2 3 4 5 6 7 8

814-12045 896-1.1012 829^1412 413-624 D52275 D52276 218-5106

9 10

237-6008 144251A1

13 14 15 15A 16 17 18 19

L18337 D143411 515-23254 515-23190 614-8025 892-11008 829-1408 143384A1

20

218-5106

21 22 23 24 25 26 27 28 31 32 33 34 35

237-6008 814-10060 D40236 D146035 D150099 829-1410 D142787 214-3188 191758A1 614-10030 '892-11010 829-1410 218-5351

36 37

237-6006 199721A1

38

199720A1

Bur 7-3350

DESCRIPTION VALVE ASSEMBLY - backhoe control, for correct assembly and components, see page 8-89 - 8-95 BOLT - hex, 12 - 1.75 x 45 mm WASHER - flat, 13.5 x 24 x 3 mm, hardened N U T - h e x , 12 m m - 1 . 7 5 , class 10 BOLT - hex, 3/8 NC x 1-1/2 inch WASHER - flat, special, 25/64 x 1-1/4 x 7/64 inch, hardened INSULATOR - rubber ELBOW - 90 degree, 3/4-16 inch flare x adj O-ring boss, stabilizer section upper and lower ports O-RING - 41/64 ID x 3/32 inch wide HOSE - 1240 mm (48-13/16 inch) long, stabilizer cylinder rod ends to stablizer section lower ports STRAP - tie, 15 inch, nylon, retaining CLAMP - P-type, 3/4 inch ID . . . . CLAMP - P-type, 1 inch ID CLAMP - P-type, 3/4 inch ID BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - lock, 8 mm , NUT - hex, 8 mm - 1 . 2 5 , class 10 HOSE - 1025 mm (40-3/8 inch) long, stabilizer section upper ports to closed ends of stabilizer cylinders ELBOW - 90 degree,,3/4-16 inch flare x adj O-ring boss, stabilizer cylinder closed ends O-RING - 41/64 ID x 3/32 inch wide BOLT - hex, 10 - 1 . 5 x 60 mm CLAMP - hose SPACER - hose clamps. PLATE-spacer N U T - h e x , 10 m m - 1.5, class 10.9 INSULATOR - rubber CLAMP - adj, 4-3/4 - 5-5/8 inch dia . PLATE - spacer, clamp BOLT - hex, full threads, 10 - 1 . 5 x 30 mm WASHER - lock, 10 mm N U T - h e x , 10 m m - 1 . 5 , class 10.9 ADAPTER - straight, 3/4-16 flare x 9/16-18 inch O-ring boss, stabilizer cylinder rod end O-RING - 15/32 ID X 5/64 inch wide CYLINDER ASSEMBLY - 1 0 8 (4-1/4) ID x 553 mm (21-3/4 inch) stroke, left-hand stabilizer, parts list page 8-133 CYLINDER ASSEMBLY - 1 0 8 (4-1/4) ID x 553 mm (21-3/4 inch) stroke, right-hand stabilizer, parts list page 8 - 1 3 3 . . . .

REQ'D. 1 2 2 .2 1 1 1 4 .1 2 2 .1 1 .1 1 1 1 2 2 1 2 .....2 2 2 2 2 2 1 .1 1 1 2 1 1 1


8-22

BT97N183


8-23

BACKHOE SWING CYLINDER HYDRAULIC CIRCUIT REF. 1

PART NO. REF

2 3 4 5 6 7 8

814-12045 896-11012 829-1412 413-624 D52275 D52276 218-5119

9 10

237-6012 196278A1

11

218-5106

12 13

237-6008 REF

14

183243A1

15 19 20 21 22 23

124690A1 218-5119 237-6012 D142787 214-1488 255659A1

24 25 26

218-5106 237-6008 182222A1

Bur 7-3350

DESCRIPTION

REQ'D.

VALVE ASSEMBLY - backhoe control, for correct assemb)ly and components, see page 8-89 - 8-95

BOLT - hex, 12 - 1.75 x 45 mm WASHER - flat,,13.5 x 24 x 3 mm, hardened

1

2 s2

NUT - hex, 12 mm - 1.75, class 10 BOLT - hex, 3/8 NC x 1-1/2 inch WASHER - flat, special, 25/64 x 1-1/4 x 7/64 inch, hardened INSULATOR - rubber ELBOW - 90 degree, 7/8-14 flare x 1-1/16-12 inch adj O-ring boss, swing section upper and lower ports O-RING - 59/64 ID x 7/64 inch wide HOSE - 700 mm (27-9/16 inch) long, includes hose guard, swing section upper port to outer rod end of left-hand swing cylinder ELBOW - 90 degree, 3/4-16 inch flare x adj O-ring boss, outer rod end of swing cylinders O-RING - 41/64 ID X 3/32 inch wide CYLINDER ASSEMBLY-102 (4) ID X 292 mm (11-1/2 inch) stroke, swing, parts list page 8-135... HOSE - 1400 mm (55-1/8 inch) long, right-hand swing cylinder outer rod end to swing section lower port RESTRICTOR - check, 1/2 inch tube ELBOW - 90 degree, 7/8-14 flare x 1-1/16-12 inch adj O-ring boss O-RING - 59/64 ID x 7/64 inch wide INSULATOR - rubber. . CLAMP - adj, 5-1/8 - 6 inch dia HOSE - 815 mm (32-3/32 inch) long, 1/2 inch ID, includes hose guard, crossover. ELBOW - 90 degree, 3/4-16 inch flare x adj O-ring boss O-RING - 41/64 ID x 3/32 inch wide RESTRICTOR - check, 4.36 mm orifice, upper and lower ports

2 1 1 1 2 1 .1 2 1 -2^ 1 2 2 .1 2 2 -2 2 1 2


8-24


8-25

* B A C K H O E BOOM CYLINDER HYDRAULIC CIRCUIT REF. 1

PART NO: REF

2 3 4 5 6 7 8

814-12045 896-11012 829-1412 413-624 D52275 D52276 218-5064

9 10

237-6012 D77182

11

193499A1

11A

193117A1

12 13 14 15 16 17 18 19 20 22 23

143439A1 176226A1 614-8025 892=11008 i43882A1 1322'12A1 814-12100 832-10412 L I 8337 142120A1 187845A1

24

218-5108

25 28

237-6012 144200A1

29

218-5123

30 31 32 33 34 35. 36 37 38 39

237-6010 142815A1 D142787 214-14104 177634A1 142122A1 133605A1 814-12080 132930A1 832-10412

DESCRIPTION VALVE ASSEMBLY - backhoe control, for correct assembly and components, see page 8-89 - 8-95 BOLT - hex, 12 - 1.75 x 45 mm WASHER - flat, 13.5 x 24 x 3 mm, hardened NUT - hex, 12 mm - 1 . 7 5 , class 10 BOLT - hex, 3/8 NC x 1-1/2 inch WASHER - flat, special, 25/64 x 1-1/4 x 7/64 inch, hardened INSULATOR - rubber. ADAPTER - straight, 1.-1/16-12 inch flare x O-ring boss, boom section upper and lower ports O-RING - 59/64 ID x 7/64 inch wide RESTRICTOR - check, boom section lower port, remove restrictor if equipped with boom lock valve circuit HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, upper port control valve through swing tower to boom HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, lower port control valve through swing tower to boom . . . CLAMP - hose, outer CLAMP - hose, center BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - lock, 8 mm CLAMP - hose, at swing tower PLATE - hose clamp, at swing tower BOLT - hex, 12 - 1.75 x 100 mm NUT - hex, self-locking, 12 mm - 1 . 7 5 STRAP - tie, 15 inch, nylon, retaining TUBE - to boom cylinder closed end hose HOSE - 1000 mm (39-3/8 inch) long, includes sleeve and banded clamps, boom cylinder closed end! ELBOW - 90 degree, 1-1/16-12 inch flare x adj O-ring boss, boom cylinder closed end, for models with boom lock valve, see page 8-59 O-RING - 59/64 ID x 7/64 inch wide CYLINDER ASSEMBLY - 127 (5) ID x 842 mm (33-5/32 inch) stroke, boom, parts list page 8-137 f. ELBOW - 90 degree, 1-1/16-12 flare x 7/8-14 inch adj O-ring boss, boom cylinder rod end O-RING - 3/4 ID X 3/32 inch wide. TUBE - boom cylinder rod end INSULATOR - rubber CLAMP - adj, 6-1/8 - 7 inch dia, tube to cylinder HOSE - 440 mm (17-3/8 inch) long, to boom cylinder rod end tube TUBE - to boom cylinder rod end hose . . CLAMP - boom cylinder tubes to inner left-hand side of boom BOLT - hex, 1 2 - 1 . 7 5 x 8 0 mm . . . . SPACER-split NUT - hex, self-locking, 12 mm - 1 . 7 5

REQ'D. .1 2 2 2

2 4 4 4

' N O T E : See pages 8-57 and 8-59 for boom lock hydraulic and electrical circuit.

Bur 7-3350


8-26

13)

CiD

8-27


BACKHOE DIPPER CYLINDER HYDRAULIC CIRCUIT REF. 1 2 3 4 5 . 6 7 8

PART NO. REF 814-12045 896-11012 829-1412 413-624 D52275 : D52276> . 2i;8-5064

9 10 11

237-6012 D142366 193499A1

11A

193117A1

12 13 14 15 16 17 18 19 20 21 22

143439A1 176226A1 614-8025 892-11008 143882A1 132212A1 814-12100 832-10412 L I 8337 142126A1 193793A1

25

REF

26 27 28 29 30 31 32 33 34 . . 35

218-5064 237-6012 ,144235A1 142124A1 133605A1 814-12080 132930A1 832-10412 218-5108 237-6012

Bur 7-3350

DESCRIPTION VALVE ASSEMBLY - backhoe control, for correct assembly and components, see page 8-89 - 8-95 BOLT - hex, 1 2 - 1.75 x 4 5 mm WASHER - flat, 13.5 x 24 x 3 mm, hardened NUT - hex, 12 mm - 1 . 7 5 , class 10 BOLT - hex, 3/8 NC x 1-1/2 inch WASHER - flat, special, 25/64 x 1-1/4 x 7/64 inch, hardened INSULATOR - rubber ADAPTER - straight, 1-1/16-12 inch flare x O-ring boss, dipper section upper and lower ports O-RING - 59/64 ID x 7/64 inch wide RESTRICTOR - check, dipper section upper port HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, upper port control yalve through swing tower to boom HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, lower port control valve through swing tower to boom CLAMP - hose, outer CLAMP - hose, center BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - lock, 8 mm CLAMP - hose, at swing tower PLATE - hose clamp, at swing tower BOLT - hex, 12 - 1.75 x 100 mm NUT - hex, self-locking, 12 mm - 1.75 ; STRAP - tie, 15 inch, nylon, retaining TUBE - to dipper cylinder closed end hose . . HOSE - 660 mm (26 inch) long, includes hose guard and clamp, dipper cylinder closed end CYLINDER ASSEMBLY - 5 (127) ID X 23 inch (583 mm) stroke, dipper, parts list page 8-139 ADAPTER - straight, 1-1/16-12 inch flare x O-ring boss O-RING - 59/64 ID x 7/64 inch wide. HOSE - 780 mm (30-3/4 inch) long, dipper cylinder rod end TUBE - to dipper cylinder rod end hose. CLAMP - dipper cylinder tubes to inner right-hand side of boom BOLT - hex, 12 - 1.75 x 80 mm SPACER-split N U T - h e x , self-locking, 12 mm-.1.75 ELBOW - 90 degree, 1-1/16-12 inch flare x adj O-ring boss O-RING - 59/64 ID x 7/64 inch wide

REQ'D. 1 2 2 2 1 1 1 2 1 1 1 .1 2 1 6 6 1 1 2 2 1 1 1 1 .1 1 .1 1 2 .4 4 .4 1 1


8-28

BT97N180

580 Super L Series 2 Loader Backhoe BACKHOE BUCKET CYLINDER HYDRAULIC

8^29 CIRCUIT

MODELS WITHOUT EXTENDABLE DIPPER REF. 1

PART NO. REF

2 3 4 5 6 7 8

814-12045 896-11012 829-1412 413-624 D52275 , D52276 218-5064

9 10

237-6012 193499A1

10A

193117A1

11 12 13 14 15 16 1-7 18 19 20 21 22 23 24 25 26 27 28 29

143439A1 176226A1 614-8025 892-11008 143882A1 132.212A1 814-12100 832-10412 L18337 141806A1 141801A1 133605A1 814-12080 132930A1 832-10412 133604A1 814-12060 832-10412 183660A1

30 31

256091A1 218-5064

32

237-6012

DESCRIPTION VALVE ASSEMBLY - backhoe control, for correct assembly and components, see page 8-89 or 8-91 BOLT - hex, 12 - 1.75 x 45 mm WASHER - flat, 13.5 x 24 x 3 mm, hardened NUT - hex, 12 mm - 1.75, class 10 BOLT - hex, 3/8 NC x 1-1/2 inch WASHER - flat, special, 25/64 x 1-1/4 x 7/64 inch, hardened INSULATOR - rubber ADAPTER - straight, 1-1/16-12 inch flare x O-ring boss, bucket section upper and lower ports O-RING - 59/64 ID x 7/64 inch wide HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, upper port control valve through swing tower to boom HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, lower port control valve through swing tower to boom CLAMP - hose, outer CLAMP - hose, center BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - lock, 8 mm CLAMP - hose, at swing tower PLATE - hose clamp, at swing tower BOLT - hex, 12 - 1.75 x 100 mm NUT - hex, self-locking; 12 mm -1.75 STRAP - tie, 15 inch, nylon, retaining TUBE - right-hand side of boom, to bucket cylinder rod end TUBE - left-hand side of boom, to bucket cylinder closed end CLAMP - bucket cylinder tubes to inner sides of boom. BOLT - hex, 1 2 - 1.75 x 80 mm SPACER - split N U T - h e x , self-locking, 12 m m - 1 . 7 5 CLAMP - tube to boom BOLT - hex, 12 - 1 . 7 5 x 6 0 mm NUT - hex, self-locking, 12 mm - 1 . 7 5 HOSE - 640 mm (25-3/16 inch) long, includes hose guard and clamp, right-hand bucket tube on boom to bucket cylinder rod end tube TUBE - bucket cylinder rod end ADAPTER - straight, 1-1/16-12 inch flare x O-ring boss, bucket cylinder rod end O-RING - 59/64 ID x 7/64 inch wide

REQ'D. 1 2 2 2 1 1 1 2 . .1 .1 1 2 .1 .6 6 1 1 2 2 1 1 1 4 8 8 8 4 4 4 1 1 1 1


Bur 7-3350


8-30

BT97N180

580 Super L Series 2 Loader Backhoe BAGKHOE BUCKET CYLINDER HYDRAULIC

8-31 CIRCUIT

MODELS WITHOUT EXTENDABLE DIPPER REF. 33

PART NO. REF

34 35

214-1472 183658A1

36 37 38 39 40

237-6012 D40236 814-10055 832-10410 182222A1

Bur 7-3350

DESCRIPTION CYLINDER ASSEMBLY - 80 (3-1/2) ID x 872 mm (34-5/16 inch) stroke, bucket, parts list page 8-141 CLAMP - adj, 4-1/16 - 5 inch dia . . . HOSE - 640 mm (25-3/16 inch) long, includes hose guard and clamps, left-hand bucket tube o h boom to bucket cylinder closed end 0-RING - 59/64 ID x 7/64 inch wide CLAMP-hose BOLT - hex, 10 - 1 . 5 x 55 mm NUT - hex, self-locking, 10 mm - 1 . 5 RESTRICTOR - check, 4.36 mm orifice,.bucket section upper port, if used

REQ'D.


8-32

580 Super L Series 2 Loader Backhoe BACKHOE BUCKET CYLINDER HYDRAULIC

8.33 CIRCUIT

MODELS WITH EXTENDABLE DIPPER REF. 1

PART NO. REF

2 3 4 5 6 7 8

814-12045 896-11012 829-1412 413-624 D52275 D52276 218-5064

9 10

237-6012 193499A1

10A

193117A1

11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

.

^

143439A1 176226A1 614-8025 892-11008 143882A1 132212A1 .814-12100 832-10412 L18337 187637A1 187639A1 133605A1 814-12080 132930A1 832-10412 133604A1 814-12060 832-10412 D143426 814-10055 D143412 832-10410 108335A1 108336A1 237-6012 103670A1 214-3132

DESCRIPTION REQ'D VALVE ASSEMBLY - backhoe control/for correct assembly and components, see page 8-93 - 8-95 1 BOLT - hex, 12 - 1.75 x 45 mm 2; WASHER - flat, 13.5 x 24 x 3 mm, hardened 2 NUT - hex, 12 mm - 1 . 7 5 , class 10 2 BOLT - hex, 3/8 NC x 1-1/2 inch • -1 WASHER - flat, special, 25/64 x 1-1/4 x 7/64 inch, hardened 1 INSULATOR - rubber. . 1 ADAPTER - straight, 1-1/16-12 inch flare x O-ring boss, bucket section upper and lower ports 2 O-RING - 59/64 ID x 7/64 inch wide. 1 HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, upper port control valve through swing tower to boom .. .1 HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, lower port control valve through swing tower to boom 1 CLAMP - hose, outer .2 CLAMP - hose, center 1 BOLT - hex, full threads, 8 - 1.25 x 25 mm ,6 WASHER - lock, 8 mm .6 CLAMP - hose, at swing tower .1 PLATE - hose clamp, at swing tower . ,.1 B O L T - h e x , 12 - 1.75 x 100 mm . . . 2 NUT - hex, self-locking, 12 mm - 1 . 7 5 2 STRAP - tie, 15 inch, nylon, retaining . . . . : . . .1; TUBE - right-hand side of boom, to bucket cylinder rod end .1 TUBE - left-hand side of boom, to bucket cylinder closed end .1 CLAMP - bucket cylinder tubes to inner sides of boom 4 BOLT - hex, 12 - 1.75 x 80 mm 8 SPACER-split 8 NUT - hex, self-locking, 12 mm -1.75 8 CLAMP - tube to boom .4 B O L T - h e x , 12 - 1.75 x 60 mm 4 NUT - hex, self-locking, 12 mm -1.75 4 CLAMP - bucket tubes to boom 4 BOLT - hex, 10 - 1.5 x 55 mm 2 SPACER - tube clamp 2 NUT - hex, self-locking, 10 mm - 1 . 5 ......2 HOSE - 1960 mm (77-1/8 inch) long, to bucket cylinder rod end tube 1 HOSE - 1 9 3 0 mm (76 inch) long, to bucket cylinder closed end 1 O-RING - 59/64 ID x 7/64 inch wide . . •. . .1 CLAMP - rubber, hose 1 CLAMP - adj, 1-1/4 - 2-1/8 inch dia 2 Continued on next page

Bur 7-3350


8-34

B9504099T

580 Super L Series 2 Loader Backhoe B A C K H O E BUCKET CYLINDER HYDRAULIC

8-35 CIRCUIT

MODELS WITH EXTENDABLE DIPPER REF. 38 39 40 41 43 44

PART NO. 184297A1 214-3132 101479A1 814-10045 832-10410 REF

45

218-5064

46 47 48 49 50 51 52 53 54

237-6012 .214-1472 D40236 814-10055 832-10410 : 136436A1 183736A1 614-10030 832-10410

Bur 7-3350

DESCRIPTION SUPPORT-hose CLAMP - adj, 1-1/4 - 2-1/8 inch dia PLATE - hose support BOLT - hex, 10 - 1 . 5 x 45 mm NUT - hex, self-locking, 10 mm - 1 . 5 CYLINDER ASSEMBLY - 80 (3-1/2) ID x 872 mm (34-5/16 inch) stroke, bucket, parts list page 8-141 ADAPTER - straight, 1-1/16-12 inch flare x O-ring boss, bucket cylinder rod end O-RING - 59/64 ID x 7/64 inch wide. CLAMP - adj, 4-1/16 - 5 inch dia OLAMP-hose B O L T - h e x , 1 0 - 1 . 5 x 5 5 mm NUT - hex, self-locking, 10 mm - 1 . 5 TUBE - bucket cylinder rod end PLATE - hose support, mounts to dipper BOLT - hex, full threads, 10 - 1 . 5 x 30 mm NUT - hex, self-locking, 10 mm - 1 . 5

REQ'D. • -1 2 1 2 2 .1 1 1 1 • -2 1 1 1 .1 2 2

Issued February,! 1998

8-36

1 LKl ^

BT97C013

580 Super L Series 2 Loader Backhoe BACKHOE EXTENDABLE DIPPER HYDRAULIC REF. 1

PART NO. REF

2 3 4 5 6 7 8

814-12045 896-11012 829-1412 413-624 D52275 D52276 218-5064

9 10

237-6012 193499A1

10A

193117A1

11 12 13 14 16 17 .

141809A1 141811A1 D40236 814-10050 832-10410 184617A1

18

,184616A1

19 20

L i 8337 218-5107

21 22

237-6010 1340969C2

23 24 -.

D140706 218-5062

25 26 27

237-6010 D38648 214-1464

Bur 7-3350

8-37 CIRCUIT

DESCRIPTION VALVE ASSEMBLY - backhoe control, for correct assembly and components, see page 8-93 - 8-95 BOLT - hex, 12 - 1.75 x 45 mm WASHER - flat, 13.5 x 24 x 3 mm, hardened NUT - hex, 12 mm - 1 . 7 5 , class 10 BOLT - hex, 3/8 NC x 1 -1/2 inch WASHER - flat, special, 25/64 x 1-1/4 x 7/64 inch, hardened INSULATOR - rubber ADAPTER - straight, 1-1/16-12 inch flare x 0-ring boss, extendable dipper section upper and lower ports. O-RING - 59/64 ID x 7/64 inch wide HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, upper port control valve through swing tower.to boom, see page 8-33, items 11-19 for hose clamping HOSE - 1295 mm (51 inch) long, includes hose guard and clamp, lower port control valve through swing tower to boom, see page 8-33, items 11-19 for hose clamping TUBE - on boom, to extendable dipper cylinder rod end TUBE - on boom, to extendable dipper cylinder closed end CLAMP - tube, on boom B O L T - h e x , 1 0 - 1 . 5 x 5 0 mm NUT - hex, self-locking, 10 mm - 1 . 5 HOSE - 850 mm (33-1/2 inch) long, includes hose guard and clamp, extendable dipper cylinder rod end HOSE - 700 mm (27^9/16 inch) long, includes hose guard and clamp, extendable dipper cylinder closed end S T R A P - t i e , 15 inch, nylon,, retaining ELBOW - 90 degree, 7/8-14 inch flare X adj 0-ring,boss, extendable dipper cylinder closed end O-RING - 3/4 ID X 3/32 inch wide CYLINDER ASSEMBLY - 76 (3) ID x 1068 mm (42 inch) stroke, extendable dipper, parts list page 8-143 TUBE - at extendable dipper cylinder rod end ADAPTER - straight, 7/8-14 inch flare x O-ring boss, extendable dipper cylinder rod end O-RING - 3/4 ID X 3/32 inch wide SPACER - rubber CLAMP - adj, 3-9/16 - 4-1/2 inch dia

REQ'D. 1 .2 .2 .2 1 .1 1 •• • • -2; . . ^1

1

1 .1 1 21 1 1 . . .1 . .1 . . . .1 1 1 1 1

•

. . .1 1 1 .. 1


8-38

m

81

BT97C143

^J:^'"^^^;?^!

8-39

580 Super L Series 2 Loader Backhoe LOADER VALVE TO BACKHOE VALVE HYDRAULIC

CIRCUIT

IVIODELS WITH OR WITHOUT EXTENDABLE DIPPER WITHOUT AUXILIARY HYDRAULICS REF. •1

PARTING. 218-5576

2 3

237-6010 243339A1

4

144477A1

5

., 218-5174

7 8 10 12 14 16

218-5057 237-6006 515-25159 614-10025 829-1410 221553A1

17 18~ 19

D132982 L I 8337 D143797

20

218-5243

21 22 23 24 25

237-6006 119895A3 237-6010 218-754 218-335

DESCRIPTION ;TEE - 3/4-16 fl branch x 1-1/16-12 fl x 7/8-14 inch adj O-ring, inlet section lower port O-RING - 3/4 ID X 3/32 inch wide HOSE - 1 2 1 0 mm (47-11/16 inch) long, swing supply, loader valve inlet section lower port to backhoe valve swing section INSULATOR - rubber, hose, see page 8-7, Ref 17-29 for mounting hardware and alternate mounting configuration ELBOW - 45 degree, 7/8-14 inch flare x swivel, at backhoe valve swing section ADAPTER - straight, 9/16-18 inch flare x O-ring boss. O-RING - 1 5 / 3 2 1 0 x 5 / 6 4 inch wide. CLAMP - P-type, 5/8 inch ID BOLT - hex, full threads, 10 - 1 . 5 x 25 mm NUT - hex, 10 mm - 1 . 5 , class 10.9 HOSE - 1860 mm (73-1/4 inch) long, signal, backhoe control valve swing section to loader control valve inlet section SLEEVE - hose guard STRAP - tie, 15 inch, nylon INSULATOR - 5/8 inch, hose, see page 8-7, Ref 17-29 for power beyond hose and mounting hardware and alternate mounting configuration TEE - 9/16-18 inch flare branch x flare x adj O-ring boss, loader valve inlet section and steering pilot hose, see page 5-5 for steering hose O-RING -15/32 ID x 5/64 inch wide SEAT - valve, swing section inlet.. . O-RING - 3/4 ID X 3/32 inch wide CAP - hex, 9/16-18.inch, if used C A P - h e x , 1-1/16-12 inch, if used

REQ'D.

1 1 1 1 1 1 2 4

1

NOTE: See pages 8-41 - 8-55 for auxiliary hydraulics.

Bur 7-3350


8-40

30

V.J---'

BT97N055

(30)

580 Super L Series 2 Loader Backhoe HAND HELD AUXILIARY

8-41

HYDRAULICS

MODELS WITH OR WITHOUT EXTENDABLE DIPPER REF. 1 2 ; 3 4 5 5A 6 7 8 9 11 12 13 14

PART NO. 121741A1 224788A2 814-12050 896-11012 814-10070 614-10025 895-11010 829-1410 218^5057 237-6006 300983A1 ' 218-5058 237-6008 137012A1

15 16 17 18 19 20 21 22 23

137713A1 136977A1 814-6060 895-11006 829-1406 515-2379 218-5128 237-6008 192693A1

27

218-5107

28 29r

237-6010 218-756

30

282428A1

31 32 33

237-6006 218-5158 237-6012

DESCRIPTION

REQ'D.

VALVE ASSEMBLY - auxiliary, hand held, one spool, parts list page 8-117 BRACKET - auxiliary valve mounting to chassis BOLT - hex, 12 - 1.75 x 50 mm WASHER - flat, 13.5 x 24 x 3 mm, hardened BOLT - hex, 1 0 - 1 . 5 x 7 0 mm BOLT - hex, full threads, 10 - 1 . 5 x 25 mm WASHER - flat, 11 x 20 x 2 mm . . NUT - hex, 10 mm - 1.5, class 10.9 ADAPTER - straight, 9/16-18 inch flare x O-ring boss O-RING -15/32 ID x 5/64 inch wide. TUBE - auxiliary valve to solenoid valve inlet ADAPTER - straight, 9/16-18 flare x 3/4-16 inch O-ring boss O-RING - 41/64 ID x 3/32 inch wide VALVE ASSEMBLY - solenoid, component parts are not serviced separately, attaches to 302803A1 chassis options harness, Ref 36 on page 4-19 BRACKET - solenoid mounting PLATE - solenoid valve mounting BOLT - hex, 6 - 1 . 0 X 60 mm WASHER - flat, 6.6 x 12 x 1.6 mm NUT - hex, 6 mm - 1 . 0 , class-10 CLAMP - P-type, 5/16 inch ID ELBOW - 90 degree, 9/16-18 flare x 3/4-16 inch adj G-ring boss O-RING - 41/64 ID x 3/32 inch wide. . . . . HOSE - 1490 mm (58-11/16 inch) long, solenoid valve outlet to check valve at loader control valve inlet section ELBOW - 90 degree, 7/8-14 inch flare x adj O-ring boss, hand held section of auxiliary valve, see hand held hydraulics on page 8-45 or 8-47 for attaching hoses . . . ; O-RING - 3/4 ID X 3/32 inch wide CAP - hex, if used, not required when hydraulic hoses for hand held hydraulics are attached to fittings VALVE - steering check, loader valve inlet section, see page 5-5 for attaching steering hose O-RING - 15/32 ID x 5/64 inch wide. . PLUG - hex, 1-1/16-12 inch O-ring boss, auxiliary valve inlet port O-RING - 59/64 ID x 7/64 inch wide

.1 1 2 2 3 1 4 4 1 1 1 1 1

: -1 1 1 2 2 . .2 1 1 1 1

2 1 2 1 . . .1 .1 1


Bur7-3350


8-42

31)

W r - - ; "^t-^'

(30)

8-43

580 Super L Series 2 Loader Backhoe HAND HELD AUXILIARY

HYDRAULICS

MODELS WITH OR WITHOUT EXTENDABLE DIPPER REF. 38

PART NO. 191532A1

39

192299A1

.

40 42

121413A1 218-5576

43 44

237-6010 243338A1

47

218-5064

48 49

237-6012 302474A1

50 51 52 53 54 55 56 57

D132982 L I 8337 136008A1 814-10050 D143422 D143797 R46493 829-1410

Bur 7-3350

DESCRIPTION SWITCH - rocker, auxiliary hydraulics, attaches to side options harness, Ref 35 on page 4-19 DECAL - auxiliary hydraulics, switch on instrument panel, see page 9-157 for decal FUSE - mini, 15 ampere TEE - 3/4-16 fl branch x 1-1/16-12 fl x 7/8-14 inch adj O-ring, at loader valve inlet section lower port, see page 5-5 for attaching steering hose O-RING - 3/4 ID X 3/32 inch wide HOSE - 910 mm (35-7/8 inch) long, loader valve inlet section lower port to auxiliary valve port ADAPTER - straight, 1-1/16-12 inch flare x O-ring boss, outlet port at auxiliary valve O-RING - 59/64 ID x 7/64 inch wide HOSE - 500 mm (19-11/16 inch) long, return,sauxiliary valve outlet port to tee at backhoe control valve SLEEVE - hose guard S T R A P - t i e , 15 inch BRACKET - mounting B O L T - h e x , 1 0 - 1 . 5 x 5 0 mm CLAMP - double tube INSULATOR - 5/8 inch SPACER - split, 22 mm (7/8 inch) long NUT - hex, 10 mm - 1 . 5 , class 10.9

REQ'D. 1 1 1 1 1 1 -2. 1 1 .2 4 .1 ;i 1 1 1 .1


8-44

580 Super L Series 2 Loader Backhoe *HAND HELD AUXBLIARY HYDRAULIGS AUXILIARY VALVE TO QUICK DISCONNECT COUPLINGS MODELS WITH 31 GALLON FUEL TANK REF. 1

PART NO. 191215A1

2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18

- D34033 180318A1 614-10025 829-1410 LI 8337 297635A1 827-10050 131600A1 191075A1 829-1410 614-10025 895-11010 218-1256 126155A1 237-6012 122179A1

19 19 20

137343A1 193261A1 122178A2

21 21

137344A1 193262A1

DESCRIPTION HOSE - 2460 mm (96-7/8 inch) long, auxiliary valve to quick disconnect couplings, see page 8-41 for 218-5107 elbows at auxiliary valve CLAMP - P-type, 1-3/16 inch ID . . BRACKET-hose support BOLT - hex, full threads, 10 - 1.5 x 25 mm . NUT - hex, 10 mm -1.5, class 10.9 STRAP-tie, 15 inch BRACKET - hose support to quick disconnect couplings BOLT - hex, 10 - 1.5x50 mm, class 10.9 SPACER - clamp. CLAMP-double NUT- hex, 10 mm -1.5, class 10.9 BOLT - hex, full threads, 10-1.5 x 25 mm WASHER - fiat, 11 x 20 x 2 mm NUT-hex, lock, bulkhead, 1-1/16 inch NF CONNECTOR - straight, bulkhead 0-RING - 59/64 ID x 7/64 inch wide. COUPLING - quick disconnect, female, component parts are not serviced separately CAP - female coupling, aluminum, if used. CAP - female coupling, black rubber, if used COUPLING - quick disconnect' male, component parts are not serviced separately CAP - male coupling, aluminum, if used CAP - male coupling, black rubber, if used

8-45

REQ'D. 2 2 . . . . .1 1 .1 3 1 1 1 -1 2 1 2 . .2 2 2

* NOTE: For a continuation of special parts used on models with hand held auxiliary hydraulics, control cables to auxiliary valve, see page 8-49.

Bur 7-3350


8-46

BT97N057

580 Super L Series 2 Loader Backhoe *HAND HELD AUXILIARY HYDRAULICS AUXILIARY VALVE TO QUICK DISCONNECT COUPLINGS MODELS WITH 40 GALLON FUEL TANK REF.:. 1 2 3 4 5 6 7 8 9 : 12 13 14 15 16 17 18

PART N O . 302501A1 301700A1 301698A1 301355A1 814-10050 D42833 892-11010 829-1410 300490A1 , 829-1410 614-10025 895-11010 218-1256 126155A1237-6012 122179A1

19 19 20

137343A1 193261A1 122178A2

21 21

137344A1 193262A1

DESCRIPTION

8-47

REQ:D.

-1340 mm (52-13/16 inch) long, auxiliary valve to quick disconnect couplings, see page 8-41 for 218-5107 elbows at auxiliary valve T U B E - to male coupling T U B E - to female coupling B R A C K E T - tube mounting HOSE

: -2

B O L T - hex, 10- 1.5x50 mm CLAMP-tube W A S H E R - lock, 10 mm

N U T - hex, 10 mm -1.5, class 10.9 - hose support to quick disconnect couplings N U T - hex, ,10 mm -1,5, class 10.9 B O L T - h e x , full threads, 10- 1.5x25 mm

BRACKET

W A S H E R - flat, 11 X 20 X 2 mm . . . . .

N U T - hex, lock, bulkhead, 1-1/1,6 inch N F C O N N E C T O R - straight, bulkhead d - R I N G - 59/64 I D X 7/64 inch wide C O U P L I N G - quick disconnect, female, component parts are not sen/iced separately C A P - female coupling,:aluminum, if used C A P - female coupling, black rubber, if used C O U P L I N G - quick disconnect, male, component parts are not sen/iced separately C A P - male coupling, aluminum, if used C A P - male coupling, black rubber, if used

2 2 2

* NOTE: For a continuation of special parts used on models with hand held auxiliary hydraulics, control cables to auxiliary valve, see page 8-49.

Bur 7-3350


8-48

8-49

580 Super L Series 2 Loader Backhoe *HAND HELD AUXILIARY HYDRAULICS CONTROL CABLES TO AUXILIARY VALVE MODELS WITH 31 OR 40 GALLON FUEL TANK REF. 1 2

PART NO. 139227A1 191076A1

3 4 5 6 7 8 9 10 . 11 12 13 14 15 16 17 18 23 24

614-8025 895-1.1008 6U-10025 895-11010 829-1410 139043A1 123942A1 96790C2 96846C2 733-2012 1340478C1 1280055C2 614-6020 895-11006 892-11006 814-10045 139230A1 83-1108

25

179683A1

26

192300A1

27 28 29

123943A1 84-2106 225-14210

DESCRIPTION KNOB-push pull, detent PLATE - control panel, hand held auxiliary hydraulics, left-hand mounting hole uses existing mounting hardware BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - flat, 9 x 17 x 1.6 mm BOLT - hex, full threads, 10 -1.5 x 25 mm WASHER - flat, 11 x 20 x 2 mm NUT - hex, 10 mm -1.5, class 10.9 BRACKET - cable support CABLE - push pull detent, lower auxiliary valve spool. CLEVIS - cable, push pull cable end PIN - clevis. . . . : PIN - cotter, 2 x 12 mm HOUSING - cable, lower auxiliary valve spool FLANGE - cable support BOLT - hex, full threads, 6 -1.0 x 20 mm WASHER - flat, 6.6 x 12 x 1.6 mm WASHER - lock, 6 mm BOLT -hex, 10- 1.5 x45 mm . KNOB - rotary, flow control SCREW - set, hex socket headless. No. 10 NC x 1/2 inch, cup point, flow contrbhknob DECAL - hand held auxilliary hydraulics, control panel plate, see page 9-157 for decal DECAL - remote auxiliary hydraulics, inside left-hand door on side of steering wheel panel, see page 9-157 for decal CABLE - flow control, rotary, upper auxiliary valve spool SCREW - set, hex socket headless. No. 10 NF x 3/8 inch, cone point NUT-hex. No. 10NF

REQ'D 1 1 2] .2 .2j r2| 2 1 1 1 :1 . .1 1 • .1 2 2 . ..2 1 .1 .1 1 1

* NOTE: For a continuation of special parts used on models with hand held auxiliary hydraulics, auxiliary valve to quick disconnect couplings, see page 8-45 or 8-47.

Bur 7-3350


8-50

<5 -^r;!)

BT97N167

580 Super L Series 2 Loader Backhoe B A C K H O E AUXILIARY HYDRAULICS AUXILIARY AND BACKHOE CONTROL VALVES TO SWING TOWER REF. 1

PART NO. ;_298772A1

4 5 6 7 8 9 9A 10

300580A1 814-10180 895-11010 829-1410 302641A1 614-18035 892-11018 218-5108 237-6012 300905A1

11 12 13

218-5108 237-6012 REF

14 15 16 17 18 19 20 21 • 22 23 24 25

218-5185 237-6012 300906A1 218-5137 237-6010 300907Ai 218-5069 237-6016 302097A1 237-6016 218-5490 218-756

26 27 28 29

293269A1 218-5138 237-6012 302472A1

30 31 32 33 34 35 36

256412A1 144479A1 144477A1 614-10030 814-10040 892-11010 829-1410

2

8-51

REQ'D DESCRIPTION VALVE ASSEMBLY - auxiliary, backinoe, component parts not available at time of printing BRACKET - mounting BOLT - hex, 10 -1.5 x 180 mm . . 2j WASHER - flat, 11 x 20 x 2 mm 2 NUT-hex, 10 mm -1.5, class 10.9 2 BRACKET - support BOLT - hex, full threads, 18 - 2:0 x 35 mm . . WASHER - lock, 18 mm ELBOW - 90 degree, 1-1/16-12 inch flare x adj O-ring boss O-RING - 59/64 ID x 7/64 inch wide. HOSE - 610 mm (24 inch) long, auxiliary valve to upper port of auxiliary section of backhoe control valve ELBOW - 90 degree, 1-1/16-12 inch flare x adj O-ring boss O-RING - 59/64 ID x 7/64 inch wide VALVE ASSEMBLY - backhoe control, 7 or 8 spool with auxiliary hydraulics, for correct assembly and components, see page 8-91 or 8-95 TEE - 1-1/16-12 inch adj O-ring branch x flare x flare O-RING - 59/64 ID x 7/64 inch wide HOSE - 460 mm (18-1/8 inch) long ELBOW - 45 degree, 7/8-14 inch flare x adj O-ring boss O-RING - 3/4 ID X 3/32 inch wide HOSE - 720 mm (28-3/8 inch) long, return ADAPTER - straight, 1-5/16-12 inch flare x O-ring boss O-RING - 1-11/64 ID X 7/64 inch wide CROSS - special O-RING -1-11/64 ID X 7/64 inch wide, not shown . . . . ; TEE - 7/8-14 flare branch x 1-5/16-12 inch flare x swivel CAP - hex, if used, not required on models with hand held auxiliary hydraulics HOSE - 755 mm (29-3/4 inch) long, main return ELBOW - 45 degree, 1-1/16-12 inch flare x adj O-ring boss O-RING - 59/64 ID x 7/64 inch wide HOSE - 2603 mm (102-1/2 inch) long, includes hose guard and (2) banded clamps, pressure port BRACKET - mounting CLAMP - isolation INSULATOR - rubber BOLT - hex, full threads, 10 - 1.5 x 30 mm BOLT - hex, 10-1.5,x 40 mm .2 WASHER-lock, 10 mm 4 NUT - hex, 10 mm - 1.5, class 10.9 4

NOTE: For a continuation of the backhoe auxiliary hydraulics at boom and dipper, see page 8-55. For backhoe auxiliary hydraulics control lever see page 9-43 and page 9-25 for backhoe control tower cover used vyith auxiliary hydraulics. Electric foot control switch is on page 4-47. Continued on next page

Bur 7-3350


8-52

^(5) (A)

^

/-A

X

1

-(45)Â

\Cl8

,

580 Super L Series 2 Loader Backhoe B A C K H O E AUXILIARY HYDRAULICS AUXILIARY AND BACKHOE CONTROL VALVES TO SWING TOWER REF. 37

PART NO. 253740A1

38 39 40 41 42 43 ,44 45 46 47 48 49 50 51

252737A1 144477A1 249775A1 249773A1 300939A1 218-335 282842A1 D74182 D143411 614-10025 300952A1 218-5062 237-6010 300884A1

8-53

DESCRIPTION HOSE - 1760 mm (69-5/16 inch) long, includes hose guard and (2) banded clamps, lower port of backhoe control valve auxiliary section to left-hand side of dipper CLAMP - auxiliary hose, at pivot block INSULATOR - rubber, at swing tower CLAMP - hose; left-hand, at swing tower CLAMP - hose, right-hand, at swing tower TUBE - low pressure return CAP-hex, 1-1/16-12 inch BRACKET - mounting, tube INSULATOR - tube CLAMP - P-type, 3/4 inch ID BOLT - hex, full threads, 10 -1.5 x 25 mm HOSE - 335 mm (13-3/16 inch) long ADAPTER - straight; 7/8-14 inch flare x O-ring boss 0-RING-3/4 ID X3/32.inch wide TUBE - small pump supply . . .

REQ'D

2 2

NOTE: For a continuation of the backhoe auxiliary hydraulics at boom and dipper, see page 8-55. For backhoe auxiliary hydraulics control lever see page 9-43 and page 9-25 for backhoe control tower cover used with auxiliary hydraulics. Electric foot control switch is on page 4-47.

Bur 7-3350


8-54

8-55


BACKHOE AUXILIARY HYDRAULICS AT BOOM AND DIPPER

REF. 1 2 4 5 6 9 10 14

PARTNO. 252885A1 252883A1 253038A1 255051A1 ; 814-12090 , 242459A1 814-10070 243679A1

14A

256210A1

15 16 17 18 19 20 21 22 23 24 25 26

246158A1 214-3156 246151A1 103670A1 214-3132 243291A1 218-676 218-1256 218-335 614-10030 .896-11010832-10410

DESCRIPTION TUBE - on boom, right-hand side TUBE - on boom, left-hand side CLAMP - tube, uses existing nut CLAMP - tube, uses existing nut BOLT-hex, 12- 1.75x90 mm. CLAMP - tube, uses existing nut BOLT-hex, 1 0 - 1 . 5 x 7 0 mm HOSE - 2625 mm (103-3/8 inch) long, includes hose guard and (2) banded clamps, models with extendable dipper HOSE - 1325 mm (52-3/16 inch) long, includes hose guard: and (2) banded clamps, models without extendable dipper SUPPORT - hose, models with extendable dipper CLAMP - adj, 2-3/4 - 3-5/8 inch dia, models with extendable dipper. SUPPORT-hose, models with extendable dipper CLAMP - rubber. : CLAMP-adj, 1-1/4-2-1/8 inch dia CLAMP - quick coupler ADAPTER - straight, 1-1/16-12 inch flare x bulkhead flare NUT - hex, lock, bulkhead, 1-1/16 inch NF CAP - hex, 1 -1 /16-12 inch BOLT-hex, full threads, 1 0 - 1 . 5 x 3 0 mm WASHER-flat, 11 X 21 x2.5 mm, hardened NUT - hex, self-locking, 10 mm -1.5 .

REQ'D. , . . . .1 1 2 2 4 2 .2 2 2 1 4 1 .1 2 1 .2 2 2 1 .1 . .1

NOTE: For a continuation of the backhoe auxiliary hydraulics at the auxiliary and backhoe - control valves, see pages 8-51 and 8-53. For backhoe auxiliary hydraulics control lever see page 9-43 and page 9-25 for backhoe control tower cover used with auxiliary hydraulics. Electric foot control switch is on page 4-47.

Bur 7-3350


8-56

GROUND LOADER

AT

CONTROL

TOWER

TO

SIDE

CONSOLE FUSE

HARNESS BLOCK

TO BOOM

LOCK

HARNESS ON

B9504049T

BOOM


8.57

BACKHOE BOOM L O C K HYDRAULIC AND E L E C T R I C A L CIRCUIT AT CONTROL TOWER AND BACKHOE VALVE REF. 1

PART NO. 189111A1 *REF

.

2 3 4

189414A1 237-6010 189601A1

5 6 7 8 9 10 11

LI 00659 L18337 D67251 LI 05735 LI 01998 376852R91 223-26

REQ'D DESCRIPTION KIT - backhoe boom lock, also includes parts on page 8-59, L111356 decal on page 9-157 and an instruction sheet, order components 1 VALVE ASSEMBLY - backhoe control, for correct assembly and components, see page 8-89.- 8-95, for valve mounting see page 8-23. . . . . .1 ELBOW - 90 degree, adjustable, see page 8-59 for attaching hose 1 O-RING - 3/4 ID X 3/32 inch wide 1 HARNESS - boom lock, at control tower to fuse block on side console harness 1 CLIP - harness 2 STRAP - tie, 15 inch .2 SWITCH - toggle, boom lock 1 PLATE-trim 1 BOOT - toggle switch 1 HOLDER - fuse, includes cap, at backhoe control tower 1 FUSE - 3AG, 5 ampere, boom lock ! . . . .1

NOTE: See page 8-59 for continuation of backhoe boom lock hydraulic and electrical circuit. *NOTE: Not included in 189111A1 kit, purchase separately.

Bur 7-3350


8-58

)C^9)(W

0


8-59

BACKHOE BOOM LOCK HYDRAULIC AND E L E C T R I C A L CIRCUIT AT BOOM CYLINDER REF.

PART NO. 189111A1

1

189957A1

2 3 4 5 6 7 , 8 9 10

D150054 D150053 413-648 495-11041 231-1446 218-5118 237-6016 192025A1 187677A1

11 12 13 14 15 16 17 18 19 20

237-6012 189709A1 218-5283 237-6006 D142787 214-31104 LI 8337' 218-5359 237-6008 189103A1

21 22 23 24 25

189263A1 515-25190 218-5382 237-6016 187612A1

26 27 28 29

D147773 221330A1 220276A1 D121385

Bur 7-3350

REQ'D. DESCRIPTION KIT - backhoe boom lock, continued from previous page, order components 1 VALVE ASSEMBLY - solenoid, backhoe boom lock, includes (2) 321-6046 warning decals, parts list page 8-121 1 PLATE - valve nriounting. 1 U-BOLT - 3/8 inch 2 BOLT - hex, 3/8 NC x 3 inch .2 WASHER - flat, 13/32 x 13/16 x 1/16 inch 6 NUT - hex, self-locking, 3/8 inch NC 6 ELBOW - 90 degree, 1-1/16-12 flare x 1-5/16T12 inch adj 0-ring boss O-RING - 1-11/64 ID x 7/64 inch wide TUBE - valve port, attaches to item 34 hose on page 8-25 . . . . . . . . . TEE - reducer. boom cylinder closed end, attaches to item 23 hose on page 8-25 O-RING - 59/64 ID x 7/64 inch wide TUBE-pilot port. ELBOW - 90 degree, 7/16-20 flare x 9/16-18 inch adj O-ring boss . . . O-RING -15/32 ID x 5/64 inch wide INSULATOR - rubber CLAMP - adj, 5-3/4 - 6-5/8 inch dia . . STRAP-tie, 15 inch ADAPTER - straight, 7/16-20 flare x 3/4-16 inch O-ring boss O-RING - 41/64 ID x 3/32 inch wide HOSE - 3700 mm (145-11/16 ihch) long, return, attaches to elbow at backhoe valve, see item 2 on page,8-57 HARNESS - boom lock valve to control tower harness CLAMP - P-type, 3/4 inch ID, return hose ELBOW - 90 degree, 1-1/16-12 flare x 1-5/16-12 inch swivel O-RING -1-11/64 ID X 7/64 inch wide TUBE - boom lock valve to boom cylinder rod end, see page 8-25, item 29 for elbow ' STRAP-tie . . . . CLAMP - hose and harness. SLEEVE - hose guard GUARD - harness protection


8-60

@

®

®

BS97N168


876I

RIDE CONTROL HYDRAULIC AND E L E C T R I C A L CIRCUIT REF. 1

PART NO. 297977A2

2

218-5145

2A 3 •

237-6008 218-5117

3A 4 5 6 7 11

237-6008 814-10140 895-11010 892-11010 240693A2 240709A4

12

240711A4

13

240706A2

14 15

240703A2 218-5220

16

218-5490

17

230078A2

19

230072A1

20

230073A1

DESCRIPTION REQ'D. VALVE ASSEMBLY - solenoid, two-way, ride control, component parts list not available at time of printing 2 ELBOW - 45 degree, 7/8-14 flare x 3/4-16 inch adj 0-ring, upper port of solenoid valves 2 0-RING - 41/64 ID X 3/32 inch wide, not shown .1 ELBOW - 90 degree, 7/8-14 flare x 3/4-16 inch adj 0-ring boss, lower port of solenoid valves 2 0-RING - 41/64 ID x 3/32 inch wide, not shown ,. .1 BOLT - hex, 10-1.5 x 140 mm '. .2 WASHER - flat, 11 x 20 x 2 mm .2 WASHER-lock, 10 mm . .4 PLATE - mounting, two-way solenoid valve .1 TUBE - left-hand solenoid valve upper port to tee at loader control valve lift section upper port 1 TUBE - right-hand solenoid valve upper port to tee at loader control valve lift section lower port .;.. 1 TUBE - left-hand solenoid valve lower port to tee at filter, models with ride control but without hydraulic tool quick coupler, see Ref 39 for models with both 1 TUBE - accumulator to right-hand solenoid valve lower port. 1 TEE - swivel, 7/8-14 inch flare branch x flare x swivel, attaches to tees at loader control valve lift section, see page 8-11 for tee at lift section upper and lower ports .2 TEE - 7/8-14flare branch x 1-5/16-12Hnch flare x swivel, attaches to existing tee at.filter (Ref 35, page 8-5). . . . . .1 HOSE - 415 mm.(1 6-3/8 inch) long,.replaces existing hose from loader i valveto filter(Ref 34, page8-5) . . . .1 TUBE - replaces existing tube (page 8-11) at loader valve upper lift port to left-hand loader lift cylinder rod end .1 TUBE - replaces existing tube (page 8-11) at loader valve lower lift port to left-hand loader lift cylinder closed end 1 Continued on next page

Bur 7-3350

Issued February, l!998

8-62

®

@

BS97N168


8-63

RIDE CONTROL HYDRAULIC AND E L E C T R I C A L CIRCUIT REF. 23

PART NO. 234412A1

24 24A 25 26 27 .

218-5600 237-6008 A13240 235002A1 296508A2

30 31 32 33

711-10030 829-1410 121413A1 :255927A1

34

256318A1

35 36 37 38

895-15010 L18337 302803A1 218-5220

39

293037A1

Bur 7-3350

DESCRIPTION REQ'D. ACCUMULATOR ASSEMBLY - hydraulic, ride control, parts list page 8-123 1 ELBOW - 90 degree, 7/8-14 flare x 3/4-16 inch adj 0-ring boss 1 0-RING - 41/64 ID x 3/32 inch wide, not shown .1 CLAMP - two piece, includes hardware 2 SWITCH - ride control, mounts in side instrument panel console .1 HARNESS - side console options, ride control switch to chassis options harness and fuse block 1 BOLT - carriage, 10 -1.5 x 30 mrn .2 NUT - hex, 10 mm - 1.5, class 10.9 .2 FUSE - mini, 15 ampere, not shown .M DECAL - Warning, do not turn the ride control on, if the loader arms and bucket are holding the front of the machine off the ground, mounts on console by ride control switch, not shown, see page 9-157 for decal .1 DECAL - Warning, pressure accumulator in loader hydraulic system, mounts on accumulator mounting plate, not shown, see page 9-157 for decal .1 WASHER - flat, 11 X 24 X 2 mm .2 STRAP-tie, 15 inch .2 HARNESS - chassis options, connects to side console options harness .1 TEE - swivel, 7/8-14 inch flare:branch x flare x swivel, models with both ride control and hydraulic tool quick coupler .1 TUBE - left-hand solenoid valve lower port to tee at filter, models with both ride control and hydraulic tool quick coupler .1


8-64

0

BS97N187


8^65

LOADER HYDRAULIC TOOL QUICK C O U P L E R REF. 1 2

PART NO. 259777A3 277320A1

3 4 5 6 7

218.-5105 237-6006 218-5057 237-6006 . 218-5220

8

293037A1

9

292528A1

10

218-5577

11 12

237-6016 276962A1

13 14 15 16 17 18 19 20 21

292436A1 711-10040 892-11010 829-1410 711-6050 895-11006 892-11006 829-1406 301008A2

22

301009A2

23 24 25 26 27 28

L18337 D138055 828-10060 120303A1 892-11010 829-1410

,

DESCRIPTION REQ'D. PLATE - mounting, solenoid valve VALVE ASSEMBLY - solenoid, four-way, two position, quick coupler, component parts not serviced separately ELBOW-90 degree, 9/16-18 inch flare xadjO-ring boss O-RING -15/32 ID x 5/64 inch wide ADAPTER - straight; 9/16-18 inch flare x 0-ring boss O-RING -15/32 ID x 5/64 inch wide TEE-swivel, 7/8-14 inch flare branch X flare X swivel, used only on models with both ride control and hydraulic tool quick coupler TUBE - left-hand ride control solenoid valve to tee at filter, replaces Ref 13 on page 8-61 on models with both ride.control and hydraulic tool < quick coupler HOSE - 1220 mm (48-1/32 inch) long, return, filter to quick coupler , solenoid valve . : TEE - 3/4-16 flare branch x 1-5/16-12 flare x adj O-ring, at inlet section upper port of loader control valve i O-RING- 1-11/64 10x7/64 inch wide. HOSE - 810 mm (31-29/32 inch) long, quick coupler solenoid valve lower port to tee at inlet section of loader control valve. TUBE - tee at loader valve inlet upper port to large pump section BOLT-carriage, 1 0 - 1 . 5 x 4 0 mm . .2 WASHER - lock, 10 mm . . . . . .2 NUT-hex, 10 mm-1.5, class 10.9... 2 BOLT - carriage, 6 -1.0 x 50 mm 2 WASHER - flat, 6.6 x12 X 1.6 mm ..2 WASHER - lock, 6 mm . . . ..2 NUT - hex, 6 mm -1.0, class 10 2 HOSE-2677 mm (1.05-13/32 inch) long, includes hose guard, (2) banded clamps and white tie strap, quick coupler solenoid valve to loader lift frame .1 HOSE - 2677 mm (105-13/32 inch),long, includes hose guard and (2) | banded clamps, quick coupler solenoid valve to loader lift frame 1 STRAP - tie, 15 inch ;14 CLAMP - tube . . . .1 BOLT - hex, 10 - 1.5 x 60 mm, class 10.9 . . . .1 SPACER - clamp 1 WASHER-lock, 10mm .1 NUT-hex, 10 mm-1.5, class 10.9. .1

NOTE: Also uses loader bucket tube clamping (Ref 19-23, page 8-13) and 139235A1 right-hand bucket cylinder link and D121194 bucket position pointer (Ref 13 and 6, page @-13). Continued on next page

Bur 7-3350


8-66

r

BS97N187


8-67

LOADER HYDRAULIC TOOL QUICK C O U P L E R REF. 29 30 31 32 33 34 35

PART NO. D138055 828-10090 120303A1 892-11010 829-1410 302803A1 296508A2

36 37 38

275488A2 121413A1 218-5490

40 41 42 43 44

304424A1 *304890A1 218-5062 237-6010 304612A1

DESCRIPTION REOjD. CLAMP-tube 4 BOLT - hex, 10 -1.5 x 90 mm, class 10,9.. SPACER - clamp, 381 mm (15 inch) long WASHER-lock, 10 mm . . . . NUT - hex, 10 mm -1.5, class 10.9 HARNESS - chassis options, connects to side console options harness HARNESS - side console options, connects to chassis options harness and fuse block SWITCH - rocker, yellow rocker and amber lens, quick coupler FUSE - mini, 15 ampere TEE - 7/8-14 flare branch x 1-5/16-12 inch flare x swivel, models without ride control CONNECTOR - straight RESTRICTOR - check ADAPTER - straight, 7/8-14 inch flare x O-ring boss 0-RING - 3/4 ID X 3/32 inch wide. HOSE - 640 mm (25-1/4 inch) long, loader coupler

* NOTE: Install restrictor on outer niost dump cylinder tube, connects to closed end of cylinder.

Bur 7-3350


8-68

© ®


8-69

LOADER HYDRAULIC TOOL QUICK C O U P L E R AT LOADER LIFT FRAME REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

PART NO. 304572A1 304574A1 300996A2 292969A2 302820A1 892-11010 829-1410 D138055 302821A1 892-11010 829-1410 D138055 814-10090 120303A1 892-11010 829-1410 307277A1 LI 8337 *303804A1 * 627-10035 *303806A1 *D138055 * 892-11010 * 829-1410

DESCRIPTION TUBE - loader lift frame to tool quick coupler frame TUBE - loader lift frame to tool quick coupler frame HOSE - 812 mm (32 inch) long, at tool quick coupler frame COUPLER - quick, tool, loader, hydraulic, see parts list page 9-23, use standard loader bucket pins to mount coupler CLAMP - extension WASHER-lock, 10mm NUT - hex, 10 mm -1.5, class 10.9 CLAMP-tube CLAMP-stud WASHER - lock, 10 mm NUT - hex, 10 mm - 1.5, class 10.9 CLAMP - tube BOLT - hex, 10 -1.5 x 90 mm SPACER - clamp, 381 mm (15 inch) long WASHER-lock, 10mm NUT - hex, 10 mm - 1.5, class 10.9 SLEEVE - hose guard STRAP-tie, 15 inch BLOCK - spacer, if used BOLT - hex, full threads, 10 -1.5 x 35 mm, class 10.9 BLOCK - spacer CLAMP-tube WASHER-lock, 10 mm NUT - hex, 10 mm -1.5, class 10.9

REQ'D.

NOTE: Also uses loader bucket tube clamping (Ref 19-23, page 8-13) and 139235A1 right-hand bucket cylinder link and D121194 bucket position pointer (Ref 13 and 6, page 9-13). * NOTE: Replaces loader auxiliary hydraulic tubes on models without loader auxiliary hydraulics (clam bucket), if used.

Bur 7-3350


8-70


8-71

EQUIPMENT HYDRAULIC PUMP REF.

PART NO. -257954A1

1 2 3 4 5 6 6A 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 . 22 ' , 22A 23 24

NSS + L32318NSS 142733A1 +111594A1 +293926A1 + 293925A1, +111596A1 111597A1 NSS NSS • 142735A1 111593A1 NSS 111588A1 326-852 S88754 S88756 111583A1 19-488 429-1010 +lil589A1 +293927A1 +293928A1 +111592A1 W16323

DESCRIPTION REQ'D. PUMP ASSEMBLY - hydraulic equipment, 17 teeth shaft gear set, used with 257948A1 flex coupling on page 8-3 COVER - shaft end SEAL - shaft COVER - closed end HOUSING - gear, shaft end PLATE - thrust, closed end 2 SEAL - used with 293925A1 backup seal 2 SEAL - backup, used with 293926A1 seal 2 SEAL - square ring, 3-1/4 |D x 3/32 inch wide, housing, closed end 2 PIN-dowel, 1/4 X 1/16 inch, closed end, gear housing . .4 SET - gear, shaft end, 17 teeth, 1-1/8 inch diameter shaft spline 1 HOUSING - center, with-ports 1 HOUSING - gear, closed end, pump 1 SHAFT - connecting 1 SET - gear, closed end 1 WASHER - flat, special, 17/32 x -15/16 x 3/16 inch 4 BOLT - hex, 1/2 NC x 3-1/4 inch, grade 8 4 BEARING - ball, sealed . . . . . . . i 1 RING - snap, retaining, spring lock 1 STUD4 WASHER-flat. 4 NUT - hex, 5/8 inch NC, grade 8 4 PLATE - thrust, shaft e n d . . . 2 SEAL- used with 293928A1 backup seal .2 SEAL - backup, used with 293927A1 seal .2 SEAL - square ring, 4-31/64 ID x 1/8 inch wide, shaft end 2 PIN - dowel, shaft end 4

-293924A1

KIT - seal, includes above items niarked with a -i-

Bur 7-3350

1


8-72

U

B9405132T

A

PART NO. ' 302965A1 .121736A2

2

302964A1

3 4 5

113793A4 132004A2 129842A2

6

218-5207

7 8 9 10 11 12 13

237-6004 * 238-6119 * 238-6127 G107251 G33965 G108870 425-106 *1346108C2

Bur 7-3350

8-73!

DESCRIPTION REQ'D. VALVE ASSEMBLY - control, loader, two spool 1 SECTION ASSEMBLY - inlet, with pilot relief valve, parts list page 8-77 : .1 SECTION ASSEMBLY-bucket, with magnetic detent and circuit relief valve, parts list page 8-79 1 SECTION ASSEMBLY - lift, with manual detent, parts list page 8-81 1 SECTION ASSEMBLY - valve, outlet, parts list page 8-83 1 VALVE ASSEMBLY - main relief, components, parts are not serviced separately, for service of external seals order G110098 seal kit 1 PLUG - hex socket, 7/16-20 inch 0-ring boss, outlet section diagnostic port 1 0-RING - 23/64 ID x 5/64 inch wide 1 0-RING -15/16 ID X 3/32 inch wide, section ports, small .9 0-RING - 1-7/16.ID X 3/32 inch wide, section ports, large 3 SHIM - section, port side of control valve 3 SHIM - section, non-port side of control valve 3 STUD - tie, 3/8 NC x 9-3/4 inch .4 NUT - hex, 3/8 inch NC 8 KIT - seal, includes above itemsmarked with an asterisk, plus additional 0-rings not required for this application.

1


8-74


8-75

LOADER CONTROL V A L V E THREE SPOOL REF. : 1

PART NO. 302966A1 121736A2

2

302964A1

3 4 5 6

113793A4 113794A4 132004A2 129842A2

7

218-5207

8 9 10 11 12 13 14

237-6004 * 238-6119 * 238-6127 G107251 G33965 G108805 425-106 *'1346108C2

Bur 7-3350

DESCRIPTION VALVE ASSEMBLY - loader control, three-spool SECTION ASSEMBLY - inlet, with pilot relief valve, parts list page 8-77 SECTION ASSEMBLY - bucket, with magnetic detent and circuit relief valve, parts list page 8-79 SECTION ASSEMBLY - lift, with manual detent, parts list page 8-81 SECTION ASSEMBLY - clam, all valves, parts list page 8-85 SECTION ASSEMBLY - outlet, parts list page 8-83 VALVE ASSEMBLY - main relief, component parts are hot serviced separately, forservice of external seals order G110098 seal kit PLUG - hex socket, 7/16-20 inch O-ring boss, outlet section diagnostic port 0-RlNG - 23/64 ID x 5/64 inch wide O-RING - 15/16 ID x 3/32 inch wide, section ports, small . . . ; O-RING -1-7/16 ID X 3/32 inch wide, section ports, large SHIM - section, port side of control valve SHIM - section, non-port side of control valve STUD - tie, 3/8 NC x 11-3/4 inch NUT - hex, 3/8 inch NC . . KIT - seal, includes above items marked with an asterisk, plus additional 0-rings not required for this application

REO'D. 1 1 1 1 1 1 1 1 1 12 4 4 4 4 8 . .1


8-76

BT97N194

580 Super L Series 2 Loader Backhoe LOADER CONTROL V A L V E INLET SECTION - WITH STEERING RELIEF VALVE REF. 1 2 3 4 5 5A 6 7. 8 9 10 11 12 14 15 16 17 18

PART NO. 121736A2 NS.S NSS 218-521.1 237-6010 122140A1 122141A1 114903A1 130060A2 G108866 425-1510 G108867 238-6012 130059A1 _G108556 237-6012 '238-6018 G35540 196095A1 196096A1

Bur 7-3350

DESCRIPTION SECTION ASSEMBLY - inlet, with pilot relief valve ; HOUSING - inlet section SPOOL - inlet section . PLUG - hex socket, 7/8-14 inch 0-ring boss 0 - R I N G - 3/4 ID X 3/32 inch wide - SPRING - outer SPRING - inner - P L U G - orifice, steering port VALVE ASSEMBLY - relief, pilot, with screen filter (Ref 1 8 ) . . BODY - pilot relief, valve NUT - hex, jam, 5/8 inch NF PLUG - adjusting, relief valve 0-RING - 3/8 ID X 1/16 inch wide SPRING - pilot relief POPPET - relief, pilot 0-RING - 59/64 ID x 7/64 inch wide, housing, large 0-RlNG - 3/4 ID X 1/16 inch wide, housing, small RING - backup, small 0-ring, housing SEAT - poppet, relief valve, used with Ref 18 screen filter. SCREEN - relief valve, filter

8-77

REQ'D.

Issued February,; 1998

8-78

(3)—O

TT9)

J_4

(25)

580 Super L Series 2 Loader Backhoe LOADER CONTROL V A L V E BUCKET SECTION - WITH MAGNETIC DETENT AND CIRCUIT RELIEF VALVE REF.

PART NO. 302964A1

1 2 3 4 5 6 7

NSS NSS *1994608C1 *65457C1 G102711 G33075 302326A1

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

118318A1 G107447 G109295 100-1125 238-5127 120148A2 238-5120 122330A1 G107780 113787A3 134621903 302246A1 134617501 1343708C1 * 238-6016 *G103862 G109391

24 25 26 27

129735A2 302247A1 G34458 237-6010 129699A1 • 1346105C2

Bur 7-3350

8-79

DESORIPTION SEOTION ASSEMBLY - bucket, with magnetic detent and circuit relief valves HOUSING - bucket section SPOOL - bucket section O-RING - spool SEAL - oil, spool RETAINER - 0-ring SEAT - centering spring SPRING - centering, spool, used in 113786A4, 113786A5 or 113786A6 sections SHAFT - magnetic detent SPRING - detent washer WASHER - detent RING - external retaining. No. 25, washer retaining O-RING -1-7/16 ID X 3/32 inch wide MAGNET - with connector O-RING - 1 ID X 3/32 inch wide PLUG - magnetic detent PLUG - check, magnetic detent HOUSING - magnetic detent VALVE ASSEMBLY - load check, hollow poppet pin POPPET - hollow poppet pin with orifice SPRING - load check PLUG - load check O-RING - 5/8 ID X 1/16 inch wide RING - backup, plug O-ring VALVE ASSEMBLY - circuit relief, 3200 psi, one piece cap, used in production, parts list page 8-87, order G109449 circuit relief valve kit for service, see page 8-99 for kit VALVE ASSEMBLY - anticavitation . POPPET - anticavitation SPRING - anticavitation O-RING - 3/4 ID X 3/32 inch wide PLUG - anticavitation

REQ'D.

2 2 .2 .1 .1 .1 .1

KIT - seal, includes above items marked with an asterisk, plus additional 0-rings not required for this application


8-80

U5)

o—®

\

1-^

B902082S

8-81

580 Super L Series 2 Loader Backhoe LOADER CONTROL V A L V E LIFT SECTION WITH MANUAL DETENT REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

PART NO. 113793A4 NSS NSS *1994608C1 *65457C1 G102711 G33075 1986612C1 G106395 G106396 G109127 211-1009 G106398 1986568C1 G106425 G109384 G107780 G33122 NSS * 238-6018 * 237-6012 *G35540 1346219C2 1343777C1 1346i75C1 1343708C1 * 238-6016 *G103862

DESCRIPTION SECTION ASSEMBLY - lift, with manual detent HOUSING - lift section SPOOL - lift section O-RING - spool SEAL - oil, spool. RETAINER - 0-ring SEAT - centering spring, upper, small SPRING - centering, spool SEAT - centering spring, lower, large. SHAFT - detent WASHER - detent, ball retainer BALL - chrome alloy steel, 9/32 inch, grade 24 RETAINER - ball stop. SPRING - detent HOUSING - detent PLUG - detent housing PLUG - check, detent plug . PLUG ASSEMBLY - load check valve port PLUG - load check valve O-RING - 3/4 ID X 1/16 inch wide, small O-RING - 59/64 ID x 7/64 inch wide, large RING - backup, small O-ring VALVE ASSEMBLY - load check, hollow poppet pin POPPET - hollow poppet pin with orifice, load check. SPRING - load check PLUG - load check O-RING - 5/8 ID X 1/16 inch wide, plug RING - backup, plug O-ring .

*1346105C2

KIT - seal, includes above items marked with an asterisk, plus additional O-rings not required for this application

Bur 7-3350

REQ'D.


8-82

O—(D

B9405134T

580 Super L Series 2 Loader Backhoe LOADER CONTROL V A L V E OUTLET SECTION REF. 1, 2 3 4 5

PART NO. 132004A2 NSS G109644 237-6008 G109646 283417A1

Bur 7-3350

DESCRIPTION . SECTION ASSEMBLY - outlet HOUSING - outlet section PLUG - load check O-RING - 41/64JD x 3/32 inch wide. SPRING - load check POPPET - load check

8-83

REQ'D.


8-84

( I > ^ o A-^
Cl>—<12)

B9502138T

8-85

580 Super L Series 2 Loader Backhoe LOADER CONTROL V A L V E CLAIVI SECTION REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

PART NO. 113794A4 NSS NSS *1994608C1 *65457C1 G102711 G33075 1994596C1 100-1647 G106410 G33080 G33122 NSS * 238-6018 * 237-6012 *G35540 1346219C2 1343777C1 1346175C1 1343708C1 * 238-6016 *G103862 129735A1 129698A1 G34458 237-6010 129699A1 *1346105C2

Bur 7-3350

DESCRIPTION SECTION ASSEMBLY - clam, three spool valve HOUSING - clam section SPOOL - clam section O-RING - spool SEAL - oil, spool RETAINER - 0-ring SEAT - centering spring SPRING - centering, purple, 2-15/16 inch free length, spool, clam section RING - heavy external retaining. No. 47 SPACER - screw CAP - centering spring, spool end, lower PLUG ASSEMBLY - load check valve port PLUG - load check valve O-RING - 3/4 ID X 1/16 inch wide, small O-RING - 59/64 ID x 7/64 inch wide, large RING - backup, small O-ring VALVE ASSEMBLY - load check, hollow poppet pin POPPET - hollow poppet pin with orifice, load check SPRING - load check PLUG - load check O-RING - 5/8 ID X 1/16 inch wide, plug RING - backup, plug O-ring VALVE ASSEMBLY - anticavitation POPPET - anticavitation SPRING - anticavitation O-RING - 3/4 ID X 3/32 inch wide PLUG - anticavitation

REQ'D.



8-86

0-®

861823S

580 Super L Series 2 Loader Backhoe LOADER CONTROL VALVE BUCKET SECTION CIRCUIT RELIEF VALVE REF. 1 2 3 4 5 6 7 8 9 10. 11 12 13

PART NO. 'G109391 NSS NSS 238-6018 G35540 NSS NSS NSS NSS NSS NSS 484-43116 425-155 237-6012 *G109449

8-87

DESCRIPTION VALVE ASSEMBLY - circuit relief, 3200 psi, one piece cap, used in production, order G109449 kit for service HOUSING - circuit relief valve : SEAT - circuit relief valve O-RING - 3/4 ID X 1/16 inch wide RING - backup POPPET - circuit relief valve. O-RING - poppet SPRING - relief, outer SPRING - relief, inner. PISTON - circuit relief valve O-RING - piston SCREW - set, hex socket headless, 5/16 NF x 1 inch, oval point . NUT - hex, jam, 5/16 inch NF. ." . O-RING - 59/64 ID x 7/64 inch wide

REQ'D. 2

KIT - service, for G109391 circuit relief valve, kit includes an instruction sheet and G109447 circuit relief valve (items 1-13) which is the same as G109391 except with a different pressure setting

N O T E : The pressure setting of the repair circuit relief valve is not preset for this application. Adjust the setting according.to the instructions sent with the repair valve or according to the service manual.

Bur 7-3350


8-88

BT97C147

8-89

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E S IVIODELS WITHOUT EXTENDABLE DIPPER WITHOUT AUXILIARY HYDRAULICS REF. 1 2 3 4

PART NO. 243135A1 243136A1 113248A2 129864A4 13661 OAS 253989A2

5 6

144321A5 241088A3

6A

243145A3

7 8 9 10 11 12 13 14 15

1542829C1 * 238-6127 * 238-6119 G107251 G33965 G108900 425-106 218-5157 237-6010 *1346107C2

Bur 7-3350

DESCRIPTION REQ'D. VALVE ASSEMBLY - backhoe control, 6 spool, foot swing, if used 1 VALVE ASSEMBLY - backhoe control, 6 spool, hand swing, if used 1 SECTION ASSEMBLY - outlet, parts list page 8-97 1 SECTION ASSEMBLY - bucket, parts list page 8-99 1 SECTION ASSEMBLY - dipper, parts list page 8-101 1 SECTION ASSEMBLY - stabilizer, left-hand and right-hand, parts list page 8-103 2 SECTION ASSEMBLY - boom, parts list pages 8-105 and 8-107 1 SECTION ASSEMBLY - swing, foot swing control valve, parts list pages 8-109 and 8-111 1 SECTION ASSEMBLY - swing, hand swing control valve, parts list pages 8-109 and 8-111 1 SECTION ASSEMBLY - inlet, parts list page 8-97 1 O-RING -1-7/16 ID X 3/32 inch wide, section ports, large 7 O-RING -15/16 ID X 3/32 inch wide, section ports, small 21 SHIM - section 7 SHIM - section 7 STUD - tie, 3/8 NC x 16-15/16 inch 4 NUT - hex, 3/8 inch NC 8 PLUG - hex, 7/8-14 inch O-ring boss, outlet section 2 O-RING - 3/4 ID x 3/32 inch wide 1 KIT - seal, includes above items marked with an asterisk, plus additional O-rings not required in this application

1


8-90

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E S MODELS WITHOUT EXTENDABLE DIPPER WITH AUXILIARY HYDRAULICS REF. 1 2

PART NO. 243139A2 243141A2 113248A2 294198A1

3: 4 5

129864A4 136610A5 253989A2

6 7

144321A5 241088A3

7A

243145A3-

8 1542829C1 9 * 238-6127 10 * 238-6119 11 . G107251 12 033965, 13 G108899 14 425-106 15 . 218-5157 16 237-6010 *1346107C2

Bur 7-3350

8-91

DESCRIPTION REQ'D. VALVE ASSEMBLY - backhoe control, 7 spool, foot swing .1 VALVE ASSEMBLY - backhoe control, 7 spool, hand swing 1 SECTION ASSEMBLY - outlet, parts list page 8-97 . . : .1 SECTION ASSEMBLY - options, auxiliary hydraulics, parts list page 8-115 -1 SECTION ASSEMBLY - bucket, parts list page 8-99 1 SECTION ASSEMBLY - dipper, parts list page 8-101 . J 1 SECTION ASSEMBLY - stabilizer, left-hand and right-hand, parts list page 8-103 2 SECTION ASSEMBLY - boom, parts list pages 8-105 and 8-107 1 SECTION ASSEMBLY - swing, foot swing control valve, parts list pages 8-109 and 8-111 1 . SECTION ASSEMBLY - swing, hand swing control valve; parts list pages 8-109 and 8-111 1 SECTION ASSEMBLY - inlet, parts list page 8-97. . .: 1 O-RING -1-7/16 ID X 3/32 inch wide, section ports, large 8 O-RING - 15/16 ID X 3/32 inch wide, section ports, small 24 SHIM - section . 8 SHIM - section 8 STUD - tie, 3/8 NC x 18-15/16 inch 4 NUT - hex, 3/8 inch NC 8 PLUG - hex, 7/8-14 inch O-ring boss 2 O-RING - 3/41D X 3/32 inch wide 1 KIT - seal, includes above items marked with an asterisk, plus additional 0-rings not required for this application

1


8-92

BT97C148

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E S MODELS WITH EXTENDABLE DIPPER WITHOUT AUXILIARY HYDRAULICS REF. 1 2 3 4 5

PART NO. 243137A1 243138A1 . 113248A2 144324A4 129864A4 . 13661 OAS 253989A2

6 7

144321A5 241088A3

7A

243145A3

8 9 10 11 12 13 14 15 16

1542829C1 * 238-6127 * 238-6119 G107251 G33965 G108899 425-106 218-5157 237-6010 *1346107C2

Bur 7-3350

8-93

DESCRIPTION REQ'D. VALVE ASSEMBLY - backhoe control, 7 spool, foot swing, if used .1 VALVE ASSEMBLY - backhoe control, 7 spool, hand swing, if used 1 SECTION ASSEMBLY - outlet, parts list page 8-97 , 1 SECTION ASSEMBLY - dipper extension, parts list page 8-113 1 SECTION ASSEMBLY - bucket, parts list page 8-99. 1 SECTION ASSEMBLY - dipper, parts list page 8-101 1 SECTION ASSEMBLY - stabilizer, left-hand and rightvhand, parts list page 8-103 2 SECTION ASSEMBLY - boom, parts list pages 8-105 and 8-107 1 SECTION ASSEMBLY - swing, foot swing control valve, parts list pages 8-109 and 8 - 1 1 1 . 1 SECTION ASSEMBLY - swing, hand swing control valve, parts list pages 8-109 and 8-111 1 SECTION ASSEMBLY - inlet, parts list page 8-97 1 O-RING - 1-7/16 ID X 3/32 inch wide, section ports, large . .8 0-RING -15/16 ID X 3/32 inch.wide, section ports, small 24 SHIM -section .8 SHIM - section 8 STUD - tie, 3/8 NC x 18-15/16 inch 4 NUT - hex, 3/8 inch NC 8 PLUG - hex, 7/8-14 inch 0-ring boss.. 2 O-RING - 3/4 ID X 3/32 inch wide 1 KIT - seal, includes above items marked with an asterisk, plus additional 0-rings not required for this application

.1


8-94

BT97N061

8-95

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E S MODELS WITH EXTENDABLE DIPPER WITH AUXILIARY HYDRAULICS REF. 1 1A

PART NO. 243142A2 243143A2 113248A2 294198A1

2 3 4 5

. 144324A4 129864A4 13661 OAS 253989A2

6 7

144321A5 ,241088A3

7A

243145A3

8 9 10 11 12 13 14 15 16

; 1542829C1 * 238-6127 * 238-6119 , G107251 ' G33965 229684A1 ,425-106 218-5157;, 237-6010 *1346107C2

Bur 7-3350

DESCRIPTION REQ'D. VALVE ASSEMBLY - backhoe control, 8 spool, foot swing 1 VALVE ASSEMBLY - backhoe control, 8 spool, hand swing 1 SECTION ASSEMBLY - outlet, parts list page 8-97 1 SECTION ASSEMBLY - options, auxiliary hydraulics, parts list page 8-115 1 SECTION ASSEMBLY - dipper extension, parts list page 8-113 1 SECTION ASSEMBLY - bucket, parts list page 8-99 1 SECTION ASSEMBLY - dipper, parts list page 8-101 1 SECTION ASSEMBLY - stabilizer, left-hand and right-hand, parts list page 8-103 2 SECTION ASSEMBLY - boom, parts list pages 8-105 and 8-107 1 SECTION ASSEMBLY - swing, foot swing control valve, parts list pages 8-109 and 8-111 1 SECTION ASSEMBLY - swing, hand swing control valve, parts list pages 8-109 and 8-111 1 SECTION ASSEMBLY - inlet, parts list page 8-97 1 O-RING -1-7/16 ID X 3/32 inch wide, section ports, large ;9 0-RING -15/16 ID X 3/32 inch wide, section ports, small 27 SHIM - section 9 SHIM-section 9 STUD-tie . .4 NUT - hex, 3/8 inch NC 8 PLUG - hex, 7/8-14 inch 0-ring boss .2 O-RING - 3/4 ID x 3/32 inch wide 1 KIT - seal, includes above items marked with an asterisk, plus additional 0-rings not required for this application

.1


8-96

B9405145S

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E INLET AND OUTLET SECTIONS REF.

PART NO.

DESCRIPTION

8-97

REQ'D.

OUTLET SECTION

1 2 3 4 5 6 7

113248A2 NSS G108902 257387A1 G33112 238-5118 218-5213 237-6014

SEOTION ASSEMBLY - outlet MANIFOLD - section body PISTON - regeneration sensing SPOOL - regeneration SPRING - regeneration spool. 0-RING - 7/8 ID X 3/32 inch wide PLUG - hex socket, 1-3/16-12 inch 0-ring boss 0-RING -1-3/64 ID x 7/64 inch wide

INLET SECTION 8 9 10 11 12

154282901 NSS 134622102 G34937 237-6010 G34458 278735A1

Bur 7-3350

SECTION ASSEMBLY - inlet. MANIFOLD - section body . VALVE ASSEMBLY - anticavitation (order items 9-12) PLUG - check valve 0-RING - 3/4 ID X 3/32 inch wide SPRING - check valve POPPET - check valve .


8-98

B921151S

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E BUCKET SECTION REF.

PART NO. 129864A4 1 " NSS 2 NSS. 3 *1994608C1 4 *65457C1 5 G102711 6 G33075 7 , G106410 8 , 1994596C1 9 .100-1647 10 G33080 134621903 11 302246A1 12 134617501 13 134370801 14 238-6016 15 = *G103862 **129861A1 16 17 18 19 20 21 22 23 24 25 26 27 .28

NSS NSS * 238-6018 *G35540 • NSS NSS NSS • NSS NSS NSS 484-431.16 •425-155 * 237-6012 '1346105C2 **G110077

8-99

DESCRIPTION SECTION ASSEMBLY - bucket, with circuit relief valves HOUSING - bucket section SPOOL - bucket section 0-RING-spool ••• SEAL - oil, spool RETAINER -0-ring SEAT - centering spring SPACER-spool SPRING - centering, purple, 2-15/16 inch free length, spool RING - heavy external retaining, No. 47, spool end CAP - centering spring, spool end VALVE ASSEMBLY - load check, hollow poppet pin POPPET - hollow poppet pin with orifice, load check SPRING - load check . PLUG - load check O-RING - 5/8 ID x 1/16 inch wide, plug RING - backup, plug 0-ring VALVE ASSEMBLY - circuit relief, bucket section, used in . production, order G110077 kit for service HOUSING - circuit relief valve SEAT - circuit relief valve O-RING - 3/4 ID X 1/16 inch wide, circuit relief valve seat RING r backup, seat O-ring FÔPPET - circuit relief valve O-RING - p o p p e t . . . . . SPRING - relief, outer SPRING - relief, inner PISTON - circuit relief valve O-RING -1/2 ID X 1/16 inch wide ' SCREW - set, hex socket headless, 5/16 NF x 1 inch, oval point NUT - hex, jam, 5/16 inch NF O-RING - 59/64 ID x 7/64 inch wide, housing.

REQ'D. 1 1 1 2 .1 -1 2 2 1 1 .A 2 1 1 1 1 2 2

KIT - seal, includes above items marked with an asterisk, plus additional O-rings not required for this application KIT - service, for 129861A1 circuit relief valve, kit includes an instruction sheet and G110078 circuit relief valve (items 16-28) which is the same as 129861A1 except with a different pressure setting.. . ;

NOTE: The pressure setting of the repair circuit relief valve is not preset for this application. Adjust the setting according to the instructions sent with the repair valve or according to the service manual.

Bur 7-3350


8-100

B9405149S

8-101

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL VALVE DIPPER SECTION REF. 1 .2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

PART NO. 136610A5 NSS NSS *1994608C1 *65457C1 G102711 G33075 G106410 1994596C1 100-1647 G33080 1346221C2 G34937 * 237-6010 G34458 278735A1 1346219C3 302246A1 1346175C1 1343708C1 * 238-6016 *G103862 **129861A1 NSS NSS * 238-6018 *G35540 NSS NSS NSS NSS NSS NSS 484-43116 425-155 * 237-6012 *1346105C2 **G110077

DESCRIPTION SECTION ASSEMBLY - dipper, with circuit relief valves and anticavitation valves HOUSING - dipper section SPOOL - dipper section O-RING - spool. SEAL - oil, spool RETAINER - 0-ring SEAT - centering spring SPACER - spool SPRING - centering, purple, 2-15/16 inch free length, spool RING - heavy external retaining, No. 47, spool end CAP - centering spring, spool end VALVE ASSEMBLY - anticavitation. (order items-11-14) PLUG - anticavitation valve. O-RING - 3/4 ID X 3/32 inch wide SPRING - anticavitation valve POPPET - anticavitation valve VALVE ASSEMBLY - load check, hollow poppet pin. POPPET - hollow poppet pin with orifice, load check SPRING - load check _ PLUG - load check O-RING - 5/8 ID X 1/16 inch wide, plug RING - backup, plug 0-ring VALVE ASSEMBLY - circuit relief, dipper section, used in production, order G.110077 kit for service HOUSING - circuit relief valve SEAT - circuit relief valve O-RING - 3/4 ID X 1/16 inch wide, circuit relief valve seat RING - backup, seat O-ring POPPET - circuit relief valve O-RING - poppet SPRING - relief, outer SPRING - relief, inner PISTON - circuit relief valve O-RING - piston . SCREW - set, hex socket headless, 5/16. NF x 1 inch, oval point NUT - hex, jam, 5/16 inch NF . . . . O-RING - 59/64 ID x 7/64 inch wide, large, housing

REO'D.

•

2 2

KIT - seal, includes above items marked with an asterisk, plus additional O-rings not required in this application KIT - service, for 129861A1 circuit relief valve, kit includes an instruction sheet and G110078 circuit relief valve (items 20-32) which is the same as 129861A1 except with a different pressure setting


Bur 7-3350


8-102

®—o

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E LEFT-HAND AND RIGHT-HAND STABILIZER SECTIONS REF. 1 2 3 . 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

PART NO. 253989A2 NSS NSS *1994608C1 *65457C1 G102711 G34463 G33075 100-1647 G33080 G33122 NSS * 237-6012 * 238-6018 G35540" 1986754C1 * 238-6018 G109627 NSS * 237-6012 * 238-6018 *G35540 *238-6019 * Gi l 0468 NSS G109630 218-5210 237-6008 *1346106C1

Bur 7-3350

DESCRIPTION SECTION ASSEMBLY - left-hand and right-hand stabilizer,, with lock check. ; HOUSING - left-hand and right-hand stabilizer sections SPOOL - left-hand and right-hand stabilizer sections 0-RING - spool. : SEAL - oil, spool RETAINER - 0-ring SPRING - centering, spool SEAT - centering spring RING - heavy external retaining, No. 47, spool end CAP - centering spring, spool end PLUG ASSEMBLY - relief . PLUG - relief 0-RING - 59/64 ID x 7/64 inch wide, large 0-RING - 3/4 ID X 1/16 inch wide, small RING - backup, small O-ring • SPOOL - shuttle, lock check 0-RING - 3/4 ID X 1/16 inch wide, shuttle spool PLUG ASSEMBLY - lock check SEAT - lock check body 0-RING - 59/64 ID x 7/64 inch wide, large, seat plug end . . . . 0-RING - 3/4 ID X 1/16 inch wide, small, seat lock check end . RING - backup, small O-ring 0-RING -13/16 ID X 1/16 inch wide, seat, center RING - backup, center O-ring POPPET - lock check SPRING - lock check PLUG - hex socket, 3/4-16 inch O-ring boss O-RING - 41/64 ID x 3/32 inch wide

8-103

REQ'D.



8-104

^

—

=

^

^—^

1-^ \

B9405135S

\

/

/

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E BOOM SECTION REF. 1 2 3 4 5 6 7 8 9 10

NSSNSS *1994608C1 *65457C1 G102711 G33075 G106410 1994596C1 100-1647 G33080' 1346221C2 (334937 * 237-6010 G34458 278735A1 1346219C3 302246A1 1346175C1 1343708C1 * 238-6016 *G103862 **G109391

11 12 . 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

PART NO. 144321A5

,

NSS NSS * 238-6018 *G35540 NSS NSS NSS NSS *1346105C2 **G109449

8-105

DESCRIPTION SECTION ASSEMBLY - boom, with circuit relief valves and anticavitation valve HOUSING - boom section SPOOL - boom section O-RING - spool SEAL - oil, spool RETAINER - 0-ring SEAT - centering spring SPACER-spool SPRING - centering, purple, 2-15/16 inch free length, spool RING - heavy external retaining. No. 47, spool end. CAP - centering spring, spool end . VALVE ASSEMBLY - anticavitation (order iterns 11-14) PLUG - anticavitation valve O-RING - 3/4 ID X 3/32 inch wide SPRING - anticavitation valve POPPET - anticavitation valve VALVE ASSEMBLY - load check, hollow poppet pin. POPPET - hollow poppet pin with orifice, load check SPRING-load check PLUG - load check O-RING - 5/8 ID X 1/16 inch wide, plug RING - backup, plug 0-ring VALVE ASSEMBLY - circuit relief, 3200 psi, upper, boom section, used in production, order G109449 kit for service HOUSING - circuit relief valve SEAT - circuit relief valve O-RING - 3/4 ID X 1/16 inch wide, circuit relief valve seat RING - backup, seat 0-ring POPPET - circuit relief valve. O-RING - poppet SPRING - relief, outer SPRING - relief, inner

REQ'D;

KIT - seal, includes above items marked with an asterisk, plus additional 0-rings not required in this application KIT - service, for G109391 circuit relief valve, kit includes an instruction sheet and 0109447 circuit relief valve (items 20-32) which is the same as G109391 except with a different pressure setting

NOTE: The pressure setting of the repair circuit relief valve is not preset for this , application. Adjust the setting according to the instructions sent with the repair valve or according to the service manual. Continued on next page

Bur 7-3350


8-106

@

—

\

(45>—O

B9405135S

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E BOOM SECTION REF.

PART N O . 144321A5 #G109391

28 29 30 31 32 33 34 35 36 37 38 39 40 • 41 42 43 44 45

NSS NSS

484-43116 425-155; * * 237-6012 :*1346023C1 NSS NSS

* * 238-6018 **G35540 NSS NSS NSS ;NSS

•

NSS NSS

'484-43120 425-1.55 * * 237-6012

8-107

DESCRIPTION SECTION ASSEMBLY - boom, with circuit relief valves and anticavitation valve VALVE ASSEMBLY-- circuit relief, 3200 psi, upper, boom section, used in production, order G109449 kit for service, continued from . previous page PISTON - circuit relief valve O-RING - piston SCREW - set, hex socket headless, 5/16 NF x 1 inch, oval point NUT - hex, jam, 5/16 inch NF O-RING - 59/64 ID x 7/64 inch wide, large, housing. . . . . VALVE ASSEMBLY - circuit relief, lower, boom section, used in production, order G110077 kit for service HOUSING - circuit relief valve SEAT - circuit relief valve O-RING - 3/4 ID X 1/16 inch wide, circuit relief valve seat RING - backup, seat O-ring POPPET - circuit relief valve O-RING - poppet. SPRING - relief, outer SPRING - relief, inner PISTON - circuit relief valve O-RING - piston SCREW - set, hex socket headless, 5/16 NF x 1-1/4 inch, oval point ' NUT - hex, jam, 5/16 inch NF O-RING - 59/64 ID x 7/64 inch wide, large, housing

#0109449

KIT - service, for G109391 circuit relief valve, kit includes an instruction sheet and G109447 circuit relief valve (items 20-3^2) which is the same as G109391 except with a different pressure setting.

*G 1-10077

KIT - service, for 1346023C1. circuit relief valve, kit includes an instruction sheet and G110078 circuit relief valve (items 33^45) which is the same as 134602301 except with a different pressure setting. . . . . . .

**1346105C2

REQ'D.

KIT - seal, includes above items marked with a double asterisk, plus additional 0-rings not required for this application


Bur 7-3350


8-108

@—i

(25)—

BS97C150

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E SWING SECTIONS REF?

PART NO. 241088A3 243145A3

1 2 3 4 5 6 7 8

NSS NSS^: *1994608C1 *65457C1 G102711 G33075 G106410 1986722C1

8A 9 10 11 12 13 14 15 16 17 18 19

1994596C1

•

100-1647 G33080 1346221C2 G34937 * 237-6010 G34458 278735A1 1346222C1 G'I 09964 *238r6015 *G108723 G109971 1978068C1 * 1346105C2

8-109

DESCRIPTION REQ'D. SECTION. ASSEMBLY - swing, uses item 8 spring, foot swing control valves, with circuit relief and anticavitation valves, if used 1 SECTION ASSEMBLY - swing, uses item 8A spring, hand swing control valves, with circuit relief and anticavitation valves, if used .1 HOUSING - swing section 1 SPOOL - swirig section -I O-RING - spool. . 2 SEAL - oil, spool 1 RETAINER - O-ring -1 SEAT - centering spring .2 SPACER-spool 2 SPRING - centering, 2-1/4 inch free length, spool, used in 241088A3 swing section 1 SPRING - centering, purple; 2-15/16 inch free length, spool, used in 243145A3 swing section ' RING - heavy external retaining,.No. 47, spool end CAP - centering spring, spool end VALVE ASSEMBLY - anticavitation (order items 11-14) PLUG - anticavitation v a l v e . . . . ; O-RING - 3/4 ID X 3/32 inch wide SPRING - anticavitation valve. POPPET - anticavitation valve VALVE ASSEMBLY - check (order items 15-17) HOUSING - valve check O-RING - 9/16 ID X 1/16 inch wide R I N G - backup ••• •••• • SPRING - valve check POPPET - valve check KIT - seal, includes above items marked with an asterisk, plus additional . 0-rings not required for this application Continued on next page

Bur 7-3350


8-110

(36)—O

BS97C150

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E SWING SECTIONS REF.

PART NO. . REF .*G107786

20 21 22 23 24 25 26 27 28 29 30 31 32

NSS NSS * * 238-6018 **G35540 NSS NSS NSS NSS NSS NSS 484-43116 • 425-155 * * 237-6012 1346219C3 302246A1 13,46175C1 ,134370801 *"238-6016 *G103862

33 34 35 36 37

*G109449

**1346105C2

8-111

DESCRIPTION REQ'D. SECTION ASSEMBLY - swing, continued from previous page. . . . . . . 1 VALVE ASSEMBLY - circuit relief, swing section, used in production, order G109449 kit for service.. 2 HOUSING - circuit relief valve SEAT - circuit relief valve O-RING - 3/4 ID X 1/16 incli wide RING - backup, seat O-ring POPPET - circuit relief valve O-RING - poppet. . SPRING - relief, inner SPRING - relief, outer - PISTON - circuit relief valve O-RING - piston SCREW - set, hex socket headless, 5/16 NF x 1 inch, oval point N U T - h e x , jam, 5/16 inch NF O-RING - 59/64 ID x 7/64 inch wide, large, housing. VALVE ASSEMBLY - load check, hollow poppet pin POPPET - hollow poppet pin with orifice,-load check S P R I N G - l o a d check PLUG - load check O - R I N G - 5 / 8 ID x 1/16 inch wide RING - backup, plug O-ring 2 KIT - service, for G107786 circuit relief valve, kit includes ah instruction sheet and G109447 circuit relief valve (items 20-32) which is the same as G107786 except with a different pressure setting

1

KIT - seal, includes above items marked with a double asterisk, plus additional 0-rings not required for this application

NOTE: The pressure setting of the repair .circuit relief valve is not preset for this application. Adjust the setting according to the instructions sent with the repair valve or according to the service manual.

Bur 7-3350


8-112

BS97C151

580 Super L Series 2 Loader Backhoe B A C K H O E CONTROL V A L V E DIPPER EXTENSION SECTION REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

PART NO. 144324A4 NSS NSS *1994608C1 *65457C1 G102711 G33075 G106410 1994596C1 100-1647 G33080 134621903 302246A1 134617501 134370801 * 238-6016 *G103862 G33122 NSS * 237-6012 * 238-6018 *G35540 134610502

Bur 7-3350

8-113

DESORIPTION SEOTION ASSEMBLY - dipper e x t e n s i o n . . . HOUSING - clipper extension SPOOL - clipper extension 0-RING - spool. SEAL - oil, spool RETAINER - 0-ring SEAT - centering spring SPAOER-spool SPRING - centering, purple, 2-15/16 inch free length, spool RING - heavy external retaining, No. 47, spool end. OAP - centering spring, spool end VALVE ASSEMBLY - load check, hollow poppet pin POPPET - hollow poppet pin with orifice, load check S P R I N G - l o a d check P L U G - l o a d check 0-RING - 5/8 ID X 1/16 inch wide RING - backup, plug Orring PLUG ASSEMBLY - relief PLUG-relief 0-RING - 59/64 ID x 7/64 inch wide, plug, large O-RING - 3/4 ID X 1/16 inch wide, plug, small RING - backup, small O-ring. KIT - seal, includes above items marked with an asterisk, plus additional O-rings not required for this application.

REQ'D. 1 1 1 2 1 1 2 -2 1 ^ ^1 1 2 1 • • -1 -1 1 2 • -2 -1 1 .1 1

1


8-114

CD

BT97N063

&


8-115

B A C K H O E CONTROL VALVE OPTIONS, AUXILIARY HYDRAULICS SECTION REF.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

16 17 18 19 20 21 22 23 24 25 26 27 28 29

PART NO. 294198A1 NSS NSS *1994608C1 *65457C1 G102711 G33075 G106410 1994596C1 100-1647 G33080 1346219C3 302246A1 1346175C1 1343708C1 * 238-6016 *G103862 **G109391 NSS NSS * 238-6018 *G35540 NSS NSS NSS NSS . NSS NSS 484-43116 425-155 * 237-6012 G106409

DESCRIPTION SECTION ASSEMBLY - options, auxiliary hydraulics, with circuit relief valves HOUSING - bucket section SPOOL - bucket section O-RING - spool SEAL - oil RETAINER - 0-ring SEAT - centering spring SPACER - spool SPRING - centering,.purple, 2-15/16 inch free length, spool RING - heavy external retaining, No. 47, spool end. CAP - centering spring, spool end VALVE ASSEMBLY - load check, hollow poppet pin. POPPET - hollow poppet pin with orifice, load check. S P R I N G - l o a d check PLUG - load check , ' O-RING - 5/8 ID X 1/16 inch wide, plug. RING - backup, plug O-ring VALVE ASSEMBLY - circuit relief, 3200 psi, options section, used in production, order G109449 kit for service HOUSING - circuit relief valve SEAT - circuit relief valve O-RING - 3/4 ID X 1/16 inch wide, circuit relief valve seat RING - backup, seat O-ring POPPET - circuit relief valve O-RING - poppet. SPRING - relief, outer. . SPRING - relief, inner PISTON - circuit relief valve O-RING - 1/2 ID X 1/16 inch wide SCREW - set, hex socket headless, 5/16 NF x 1 inch, oval point N U T - h e x , jam, 5/16 inch NF O-RING - 59/64 ID x 7/64 inch wide, housing SCREW - spool end

*1346105C2


'G109449

KIT - service, for G109391 circuit relief valve, kit includes an instruction sheet and G109447 circuit relief valve (items 16-28) which is the same as G109391 except with a different pressure setting.

REQ'D.

2 2


Bur 7-3350


8-116

1

580 Super L Series 2 Loader Backhoe AUXILIARY V A L V E HAND HELD HYDRAULICS ONE SPOOL REF. 1 3

PART NO. 121741A1 121638A2 131197A1

4 5 6 7 8. 9 10 11 12 13

121639A2 218-5158 237-6012 238-6117 238-6112 137039A1 134612903 829-1312 134612803 829-1310

Bur 7-3350

8-117

DESORIPTION VALVE ASSEMBLY - auxiliary, for hand held hydraulics MANIFOLD - cover, inlet/outlet SEOTION ASSEMBLY - hand held auxiliary hydraulics, parts list page 8-119 MANIFOLD - cover, power beyond PLUG - hex, 1-1/16-12 inch O-ring boss 0-RING - 59/64 ID x 7/64 inch wide O-RING -13/16 ID X 3/32 inch wide, section ports, large O-RING - 1 / 2 ID X 3/32 inch wide, section ports, small PLUG - hex socket STUD-tie NUT - hex, 12 mm - 1 . 7 5 , class 10 STUD-tie NUT - hex, 10 mm - 1 . 5 , class 10.9

REQ'D. 1 1 1 1 1; 1 . .6 2 1 • • -2 4 1 2


8-118

BT97C153

580 Super L Series 2 Loader Backhoe AUXILIARY V A L V E HAND HELD SECTION REF. 1 2 3 4 . 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

30 31 32 33 34 • 35 36 37 38 39

PART NO. 131197A1 NSS 71121 G110391 131196A1 NSS G1-10391 G108630 237-6002 1980085C1 G108914 130932A1 G108913 1980084C3 G108912 211-1007 G108911 130919A1 1341975C1 100-21118 G107780 238-6011 238-6015 129391A1 61-31016;495-11022 1542563C1 NSS G108723 238-6015 1994581C1 1543329C1 1343791C2

40 41 42 43

1980302C2 38-1812 G101066 ' 1980227C1 1986628C1 1980226C1 237-6010 G108956 F13537 G108957 1994677C1 100-2156 1346312C2 238-6012 1957856C1

44 45

1957855C3 1957887C1

Bur 7-3350

8-119

DESCRIPTION SECTION ASSEMBLY - hand held auxiliary hydraulics HOUSING - section WIPER - shaft seal O-RlNG - spool SPOOL ASSEMBLY - detent . SPOOL - detent O-RING-spool RETAINER - O-ring 0 - R l N G - 1 / 4 ID x 1/16 inch wide STOP - spool SEAT - spring, upper SPRING - centering SEAT - spring, lower SHAFT - detent WASHER - detent, ball BALL - chrome alloy steel, 7/32 inch, grade 24 WASHER - detent, ball SPRING - detent RETAINER - detent, spring RING - internal .retaining. No. 118 ;.. . PLUG - check valve O-RING - 5/16 ID X 1/16 inch wide O-RING - 9/16 ID X 1/16 inch wide HOUSING - detent BOLT - hex socket, 10 NC x 1 inch, detent housing retaining WASHER - flat, 7/32 x 7/16 x 3/64 inch VALVE ASSEMBLY - check PLUG - load check RING - backup O-RING - 9/16 ID X 1/16 inch wide SPRING - load check PLUG - poppet KIT - flow control adjustment, includes an instruction sheet (order items 30-39) ROD ASSEMBLY - adjusting, flow control . . . PIN - roll, 1/8 X 3/4 inch SEAL - oil, adjusting rod NUT - compression O-RING - 3/8 ID X 9/16 inch wide, rod seal PLUG - adjusting, flow O-RING - 3/4 ID X 3/32 inch wide RACE - bearing, thin BEARING - thrust RACE - bearing, thick SLEEVE ASSEMBLY - control RING - internal retaining. No. 56 PLUG - sleeve O-RING - 3/8 ID X 1/16 inch wide SPOOL - flow control, select fit with item 44 sleeve, must retain together S L E E V E - f l o w control -SPRING - control, flow control, not included in sleeve a s s e m b l y . . .

REQ'D.


8-120

(3>-0

( 3 > - 0

B910459S


8-121

BOOM L O C K SOLENOID VALVE REF.

PART NO. 189957A1 *G110467

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

NSS NSS 238-6018 G35540 NSS - NSS NSS NSS NSS NSS 484-43116 425-155 237-6012 NSS 221168A1 D150781 D150810

*G110077

DESORIPTION VALVE ASSEMBLY - solenoid, backhoe boom lock, includes (2) 321-6046 warning decals, see page 9-157 for decal RELIEF ASSEMBLY - circuit, solenoid, used in production, order G i l 0077 kit for service BODY - relief valve SEAT - relief valve O-RING - 3/4 ID x 1/16 inch wide, relief valve seat RING - backup, seat O-ring POPPET - relief valve O-RING - poppet SPRING - relief, outer SPRING - relief, inner. PISTON - relief valve O-RING - piston SOREW - set, hex socket headless, 5/16 NF x 1 inch, oval point N U T - h e x , jam, 5/16 inch N F ; O-RING - 59/64 ID x 7/64 inch wide BODY - solenoid SOLENOID - relief, with connector, 12 volt KIT - repair, includes (3) springs, (1) ball, (1) poppet, and (1) plug which are not serviced separately and D150810 seal kit, not shown KIT - seal, includes (9) O-rings and (2) backup rings which are not service separately, not shown KIT - service, for G i l 0467 circuit relief valve, includes G110078 circuit relief valve assembly (items 1 through 13) and an instruction sheet

REQ'D. 1 .....1 1 1 .1 1 • • ^1 • .1 .1 1 1 1 .1 1 1 1 1 1 1

1

*NOTE: The pressure setting of the repair circuit relief valve is not preset for this application; Adjust the setting according to the instructions sent with the repair valve.

Bur7-3350


8-122

BS97C154


8-123

ACCUMULATOR A S S E M B L Y RIDE CONTROL REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14

PART NO. 234412A1 -NSS . 192895A1 276-2456 1978142C1 NSS 1978143C1 1978144C1 1978158C1 1978141 C I NSS NSS NSS NSS NSS L129440

Bur 7-3350

DESCRIPTION ACCUMULATOR ASSEMBLY - hydraulic, ride control BODY - accumulator, tube GUARD-valve SCREW - self-tapping, hex head, No. 10 NC x 3/8 inch VALVE ASSEMBLY - charge, gas VALVE - accumulator charging CORE - valve CAP-valve O-RING-valve KIT - seal, includes (1) V-type O-ring, (2) Teflon bearing rings and (1) body end seal ring GLAND - gas valve O-RING - gland RING - backup, if used PISTON - accumulator. GLAND - end cap DECAL - hydraulic accumulator application instructions, mounts on accumulator, not shown, see page 9-157 for decal

REQ'D. 1 1 1 .2

1 1 2 2 .1 • • • "I 1


8-124

6

B9405152S


8-125

HYDRAULIC OIL FILTER REF. 1 2 3 4 5 6 7 8 9

PART NO. 122536A1 NSS N6755 N6941 129-667 493-21020 237-6006 238-5011 NSS NSS N9025 NSS 238-5230

Bur 7-3350

DESCRIPTION FILTER ASSEMBLY - hydraulic oil HEAD-filter INDICATOR ASSEMBLY - restriction, electric KIT - restriction indicator repair (order items 2-5) NUT - hex, left-hand thread, No. 10 NF. . . . . WASHER - internal tooth lock, 3/16 inch. . . . O-RING -15/32 ID x,5/64 inch wide, outer.. . 0-RING - 5/16 ID X 1/16 inch wide, inner . . . , INDICATOR - restriction, electric VALVE - bypass. . . ELEMENT ASSEMBLY - filter ELEMENT - filter O-RING - 2-1/2 ID X 1/8 inch wide, filter to head

REQ'D.


8-126


8-127

LOADER LIFT GYLINDERS REF. 1

PART N O . 112366A2

DESCRIPTION C Y L I N D E R A S S E M B L Y - 8 3 (3-1/4) I D

REQ'D:

x 7 6 6 mm ( 3 0 - 1 / 8 inch) stroke,

lift, right-hand and left-hand, see note i2 3 4 5 6

7 8 . 9 10 11 12 13 14 15 16 17 18 19

.

112432A1 1980335G1

T U B E A S S E M B L Y - cylinder

NSS

G L A N D A S S E M B L Y - cylinder

1980321C2 * D95143 *G102425 *1542875C1 1542999C1 1542998C1 * 238-5233 *G32122 -276-2446 133083A1 ' 135161A1 *G102287 * SI 09444 * SI 09445 25974R1 G32303 219-1 1543260C1

2 1

BUSHING-tube

••

2

- seal, includes all items with an asterisk and an instruction sheet.

.1

G L A N D - cylinder WIPER

- piston rod

B U S H I N G - center

- seal, N S S , order 1 5 4 3 2 6 0 C 1 kit below - rod, N S S , order 1 5 4 3 2 6 0 C 1 kit below. . - buffer, N S S , order 1 5 4 3 2 6 0 C 1 kit below 0 - R I N G - 2-7/8 I D x 1/8 inch wide, gland R I N G - backup S C R E W - self-tapping, hex head, No. 8 N C x 3/8 inch R O D - piston, 4 4 mm (1 -3/4 inch) diameter, cylinder, without bushings KIT

SEAL SEAL

P I S T O N - cylinder

- piston - backup, piston seal - wear, piston - hex, 1 N F x 2-1/2 inch, grade 8 W A S H E R - flat, special, 1 inch, hardened F I T T I N G - grease, straight, 1/8 P T x 2 1 / 3 2 inch SEAL RING RING BOLT

- KIT

NOTE: The cylinder assembly part number is stamped on some cylinder glands or tubes.

Bur 7-3350


8-128


8-129

LOADER B U C K E T CYLINDERS REF. 1 2 3 4 5 . 6 7 8 9 10 11 12 13 14 15 16 17 18 19

PART NO. 113133A2 1131,35A2 G108512 NSS G109881 *D95142 *GJ 02424 * 1542874C1 1542997C1 1542996C1 *238-5231 *G109298 276-2446 110307A1 G108518 *G102288 *G100444 *G100449 25863R1 S94643 219-55

DESCRIPTION CYLINDER ASSEMBLY - 76 (3) ID x 522 mm (20-9/16 inch) stroke, bucket, left-hand and right-hand, includes bushings in cylinder tube and without bushings at rod eye, see note TUBE ASSEMBLY - cylinder .. BUSHING-tube GLAND ASSEMBLY - cylinder GLAND - cylinder WIPER - piston rod BUSHING - center, gland KIT - seal, NSS, order 1543256C1 kjt below SEAL - rod, NSS, order 1543256C1 kit below. SEAL - buffer, NSS, order 1543256C1 kit below. 0-RING - 2-5/8 ID x 1/8 inch wide, gland RING - backup, gland 0-ring SCREW - self-tapping, hex head," No. 8 NC x 3/8 inch ROD - piston, 38 mm (1-1/2 inch) diameter, without bushings in eye PISTON - cylinder .SEAL-piston jRING - backup, piston seal I RING - wear, piston iBOLT-hex, 3/4 NFx 2-1/2 inch, grades WASHER - flat, special, hardened FITTING - grease, 90 degree, 1/8 PT x 27/32 inch . . .

* 1543256C1

KIT - seal, includes all items with an asterisk and an instruction sheet.

REQ'D. -2 1 • .2

.

.1


Bur 7^3350


8-130


8-131

LOADER CLAM CYLINDERS REF. 1

PART NO. 1346189C1

1

1346190C1

2 2 3

1346191 CI 1346192C1 30634 NSS G109884 *D95143 *G102425 *1542875C1 1542999C1 1542998C1 * 238-5231 *G109298 276-2446 1346195C1 30634 1340798C1 *G102288 *G100444 *G100449 25974R1 G32303 219-1 219-55

DESCRIPTION CYLINDER ASSEMBLY - 76 (3) ID x 231 mm (9 inch) stroke, clam, right-hand, see note CYLINDER ASSEMBLY - 76 (3) ID x 231 mm (9 inch) stroke, clam, left-hand, see note TUBE ASSEMBLY - cylinder, right-hand TUBE ASSEMBLY - cylinder, left-hand BUSHING - 1346191C1 or 1346192C1 tube GLAND ASSEMBLY - cylinder GLAND - cylinder WIPER - piston rod BUSHING - center KIT - seal, NSS, order1543267C1 kit below SEAL - rod, NSS, order 1543267C1 kit below SEAL - buffer, NSS, order 1543267C1 kit below 0-RING - 2-5/8 ID x 1/8 inch wide, gland RING - backup, gland 0-ring SCREW - self-tapping, hex head. No. 8 NC x 3/8 inch ROD ASSEMBLY - piston, 44 mm diameter BUSHING PISTON - cylinder SEAL - piston RING - backup, piston seal RING - wear, piston BOLT - hex, 1 NF x 2-1/2 inch, grade 8 WASHER - flat, special, 1 inch, hardened FITTING - grease, straight, 1/8 PT x 21/32 inch FITTING - grease, 90 degree, 1/8 PT x 27/32 inch

*1543267C1


4 5 6 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

REQ'D.


Bur 7-3350


8-132

a

c BS97C156

580 Super L Series 2 Loader Backhoe B A C K H O E STABILIZER C Y L I N D E R S (9/16 INCH THREADED SPUD ON CYLINDER TUBE) REF. 1

PART NO. 199720A1

1

199721A1

2 2

199722A1 199723A1 NSS G110519 *D95144 *G101533 *1542876C1 1543001 CI 1543000C1 * 238-5241 *G32176 276-2446 123726A1 123732A1 * G i l 0531 * G i l 0529 *G110530 28-2048 G104989 219-1

DESCRIPTION CYLINDER ASSEMBLY - 108 (4-1/4) ID x 553 mm (21-3/4 inch) stroke, stabilizer, right-hand, without tube or rod bushings, see note CYLINDER ASSEMBLY -108 (4-1/4) ID x 553 mm (21-3/4 inch) stroke, stabilizer, left-hand, without tube or rod bushings, see note TUBE - cylinder, right-hand TUBE - cylinder, left-hand GLAND ASSEMBLY - cylinder GLAND - cylinder WIPER - piston rod BUSHING - center KIT - seal, NSS, order 1543275C1 kit below SEAL - rod, NSS, order 1543275C1 kit below SEAL - buffer, NSS, order 1543275C1 kit below O-RING - 3-7/8 ID X 1/8 inch wide, gland RING - backup, gland 0-ring SCREW - self-tapping, hex head. No. 8 NC x 3/8 inch ROD - piston, 51 mm (2 inch) diameter PISTON - cylinder SEAL - piston RING - backup, piston seal RING - wear, piston BOLT - hex, 1-1/4 NF x 3 inch, grade 8 WASHER - flat, hardened, special, 1-1/32 x 2-3/8 x 3/16 inch FITTING - grease, straight, 1/8 PT x 21/32 inch

* 1543275C1

KIT - seal, includes all items with an asterisk and an instruction sheet

4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

8-133

REQ'D.

1


Bur 7-3350


8-134

BT95G091

8-135

BACKHOE SWING CYLINDERS REF. 1

PART NO. 139808A2

2

199953A2

2

139810A2

3

124568A2 NSS 0109899 *D95144 *G101533 *1542876C1 154300101 1543000C1 * 238-5239 *G109299 276-2446 177518A1 137248A1 100-21315 112370A3 *121478A1 *G102285 *G100440 *G100448 28-1664 G32303 219-1 219-55 124462A1 124463A1 238-5242 G32176

DESCRIPTION CYLINDER ASSEMBLY -102 (4) ID X 292 mm (11-1/2 inch) stroke, swing, see note TUBE ASSEMBLY - cylinder, includes 139810A2 tube, 124462A1 end cap assembly (Ref 22-24) and (1) 276-2446 screw (Ref 11), not available as an assembly, order components TUBE ASSEMBLY - cylinder, does not include 124462A1 end cap assembly or (1) 276-2446'screw BUSHING - tube, external GLAND ASSEMBLY - cylinder. GLAND - cylinder WIPER-piston rod. . . . BUSHING - center KIT - seal, NSS, order 122535A1 kit below SEAL - rod, NSS, order 122535A1 kit below. SEAL - buffer, NSS, order 122535A1 kit below. . . 0-RING - 3-5/8 X 1/8 inch wide, gland RING - backup, gland 0-ring SCREW - self-tapping, hex head. No. 8 NC x 3/8 inch ROD ASSEMBLY - piston, 51 mm (2 inch) diameter BUSHING - piston rod, self-aligning RING - internal retaining. No. 315 PISTON - cylinder RING - cast iron, 4 inch OD SEAL- • piston RING - backup, piston seal RING- wear, piston BOLT • hex, 1-14 X 4 inch, grade 8 WASHER - flat. special, 1 inch, hardened FITTING - grease, straight, 1/8 PT x 21/32 inch FITTING - grease, 90 degree, 1/8 PT x 27/32 inch CAP ASSEMBLY - end, order items 22-24 CAP - end 0-RING-4 ID x 1/8 inch wide RING - backup

*122535A1


4 5 6 7 8 9 10 11 12 13 13A 14 14A 15 16 17 18 19 20 21 22 23 24

REQ'D. 2

.1


Bur 7-3350


8-136

(25)-^

B9405141T

&


8-137

BACKHOE BOOM CYLINDER REF. 1 2 3

PART NO. 144200A1

10 11 13 14 15 16 17 18 19

144201A1 1346101 CI NSS 1542918C1 *D95145 *G102426 *1542877C1 1542929C1 1542928C1 * 238-5247 *G107970 276-2446 123405A6 123407A1 1346018C2 1958028C1

20-

237-6006

21 22 23 24 25

* G i l 0269 *G102090 28-2048 G104989 219-1

6 7 8

*1542919C2

DESCRIPTION CYLINDER ASSEMBLY -127 (5) ID x 842 mm (33-5/32 inch) stroke, boom, without grease seals at rod and tube eyes, see note TUBE ASSEMBLY - cylinder BUSHIN(3 - tube . GLAND ASSEMBLY - cylinder GLAND - cylinder, has identification groove on outer lip WIPER - piston rod BUSHING - center KIT - seal, NSS, order 1542919C2 kit below SEAL - rod, NSS, order 1542919C2 kit below SEAL - buffer, NSS, order 1542919C2 kit below 0-RING - 4-5/8 ID x 1/8 inch wide, gland RING - backup, gland 0-ring SCREW - self-tapping, hex head,,No. 8 NC x 3/8 inch ROD ASSEMBLY - piston, 57 mm (2-1/4 inch) diameter BUSHING- rod . PISTON - cylinder, used with 1958028C1 relief valve cartridge VALVE ASSEMBLY - relief, cartridge, internal component parts not sen/iced separately O-RING -15/32 ID x 5/64 inch wide, relief valve cartridge, external SEAL - piston RING - wear, piston BOLT - hex, 1 -1/4 NF x 3 inch, grade 8 . . . . WASHER - flat, hardened, special, 1 -1/4 inch FITTING - grease, straight, 1/8 PTx 21/32 inch KIT - seal, includes all items with an asterisk; also includes G108712 piston rod wiper not used in this application, and an instruction sheet

REQ'D.

2 1


Bur 7-3350


8-138


8-139

BACKHOE DIPPER CYLINDER REF. 1 2 4 5 6 8 9 11 12 13 14 15 16 17 18 19 20 21 22

'

PART NO. 183795A2 183796A2 NSS 1542914C1 *D95146 *G102427 *1542879C1 1542931 CI ' 1542930C1 * 238-5247 *G107970 - 276-2446 17885PA1 D141555 G110569 *1986753C1 *G102092 ' *G102090 25987R1 G104990 219-1 *1542915C2

DESCRIPTION CYLINDER ASSEMBLY -127 (5) ID x 583 mm (23 inch) stroke, dipper, see note. TUBE - cylinder GLAND ASSEMBLY - cylinder GLAND - cylinder WIPER - piston rod BUSHING - center KIT - seal, NSS, order 1542915C2 kit below SEAL - rod, NSS, order 1542915C2 kit below. ., SEAL - buffer, NSS, order-1542915C2 kit below O-RING -4-5/8 ID X 1/8 inch wide, gland RING - backup, gland 0-ring SCREW - self-tapping, hex head, No. 8 NC x 3/8 inch ROD ASSEMBLY - piston, 64 mm (2-1/2 inch) diameter, cylinder BUSHING - rod PISTON - cylinder SEAL - piston RING - backup, piston seal RING - wear, piston BOLT - hex, 1-1/2 NFx 3-1/2 inch, grade 8, WASHER - flat, hardened, special, 1-1/2 inch FITTING - grease, straight, 1/8 PTx 21/32 inch KIT - seal, includes all items with an asterisk, also a seal and wiper not used in this application, and an instruction sheet

REQ'D.

2 1


Bur 7-3350


8-140

c. BS97C157


8-141

BAGKHOE B U C K E T CYLINDER REF. 1

PART N O . 235916A1

2

235917A2

T U B E A S S E M B L Y - cylinder

NSS

G L A N D A S S E M B L Y - cylinder

DESCRIPTION

REQ'D:

C Y L I N D E R A S S E M B L Y - 8 0 ( 3 - 1 / 2 ) I D x 8 7 2 mm ( 3 4 - 5 / 1 6 inch) stroke,

bucket, see note

4 5 6 8 9 11 12 13 14 15 16 17 18 19 20 21 22

235921A1 *D95146. *G109908 *1542879C1 1542931 C I 154293bC1 * 238-5235 * D38858 276-2446 •l96164A1 D140029 .1986906C1 *G102286 *G100710 *G100711 28-2052 G104989 219-1 * 1542923C2

G L A N D - cylinder W I P E R - piston rod B U S H I N G - center

K I T - seal, N S S , order 1 5 4 2 9 2 3 C 2 kit below S E A L - rod, N S S , order 1 5 4 2 9 2 3 C 2 kit below

S E A L - buffer, N S S , order 1 5 4 2 9 2 3 C 2 kit below 0 - R I N G - 3 - 1 / 8 I D X 1/8 inch wide, gland R I N G - backup

S C R E W - self-tapping, hex head. No. 8 N C x 3 / 8 inch R O D A S S E M B L Y - piston, 6 4 mm ( 2 - 1 / 2 inch) diameter, cylinder. B U S H I N G - 5 0 x 6 0 x 2 5 . 5 m m long, piston rod P I S T O N - cylinder S E A L - piston

RING - backup, piston seal R I N G - wear, piston B O L T - hex, 1-1/4 N F x 3 - 1 / 4 inch, grade 8 W A S H E R - flat, hardened, special, 1-1/4 inch F I T T I N G - grease, straight, 1/8 P T x 2 1 / 3 2 inch

.2

K I T - seal, includes all items with an asterisk and an instruction sheet.

.1


Bur 7-3350


8-142

(ID Qi

B9405143T


8-143

BACKHOE DIPPER EXTENSION CYLINDER REF. 1 2

PART N O . 1340969C2 1340970C1 NSS

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

G109884 *D95143 *G102425 *1542875C1 1542999C1 1542998C1 ^ * 238-5231 ,*G109298 276-2446 1980296G1 G107277 *G102288 *G100444 *G100449 25863R1 S94643 * 154326701

DESORIPTION OYLINDER ASSEMBLY - 76 (3) ID x 1068 mm (42 inch) stroke, dipper extension, see note TUBE - cylinder, without bushing GLAND ASSEMBLY - cylinder GLAND - cylinder WIPER - piston rod BUSHING - center KIT - seal, NSS, order 154326701 kit below SEAL - rod, NSS, order 154326701 kit below. . . SEAL - buffer, NSS, order 154326701 kit below O-RING - 2-5/8 ID x 1/8 inch wide, gland . RING - backup, gland O-ring SOREW - self-tapping, hex head. No. 8 NO x 3/8" inch . . : ROD - piston, 44 mm (1-3/4 inch) diameter, without bushing PISTON - cylinder SEAL - piston RING - backup, piston seal RING - wear, piston BOLT - hex, 3/4 NF x 2-1/2 inch, grade 8 WASHER - flat, special, hardened

REQ'D.



Bur 7-3350



9-1

A L P H A B E T I C A L INDEX CHASSIS DESCRIPTION Backhoe Boom. Boom Latch....... Buckets...... Control Tower and Covers Controls Controls - Backhoe Auxiliary Hydraulics Controls - Excavator Control Pattern Dipper and Bucket Extendable Dipper., Stabilizers, Plates, and Pads Swing Cylinders and Swing Tower Battery Box and Right-Hand Step Cab Air Conditioner, Heater, and Blower Air Filter Control Panel and Wiring Doors and Mounting and Rear Window Frame, Covers and Insulation Glass : Headliner, Louvers, and Dome Lamp Windshield Washers and Wipers Canopy-ROPS Chassis Countenweight - Front Couplers - Quick, Loader Hydraulic Tool Decals..... Fenders and Closure Panels Floor Plates and Mats Frost Point Assembly Guard-Mud... Guard - Pump and Baffle Plates Hood, Engine Side Panels, and Grille Unit Loader Antirollback Control/Return-To-Dig Control Buckets Bucket and Lift Controls Clam Controls Frame and Mounting Parts Guard - Valve : Links - Bucket and Cylinder Self-Leveling Control Mirror - Rear View Radiator Wrapper Seats and Seat Mounting Parts Slow Moving Vehicle Emblem Tank - Hydraulic Oil

Bur 7-3350

PAGE

^ ^

,

• '.

9-49,9-51 9-53 9-63-9-71 9-25,9-27 9-29-9-41 -...9-43 9-39 9-55,9-57 9-59,9-61 ....9-45 9-47 9-79,9-81 9-137 - 9-145 9-135 .9-125 9-117 - 9-123 9-115 9-113 9-133 9-127 - 9-131 9-147 .....9-77 9-75 9-23 9-153 - 9-157 9-97,9-99 9-95 9-73 9-101 9-85 - 9-89 9-91,9-93 9-11 9-15-9-19 9-3 9-5,9-7 9-11 ^9-21 9-13 9-9 i 9-149 9-83 9-103 - 9-111 i... 9-151 9-79


9-2

(18>—®

BT97N067


9-3

LOADER LIFT AND B U C K E T CONTROLS REF. 1

PART NO. 292904A1

1A

293262A1

2

256347A1 258616A1 298176A1 345-133 133615A1

3 4 5 6 7 8 9 10 11 12 13 14 14A 15 16 17 18 19 20; 21 22 23 24 25 26 27 28 29 29A 30 31 32

140-107 131-623 132661A1 195615A1 614-6016 495-11028 495-81184 176311A1 108088A1 102761A1 432-828 112380A1 465004R91 614-6016 396-41028 D136773 231-1446 ,413-628 496-21041 425-106 425-116 122359A1 120204A1 132931A1 D149288 432-612 302965A1 814-10040 896-11010 614-6020 396-41028 829-1406

Bur 7-3350

DESCRIPTION HANDLE - control lever, loader, two button, declutch and differential . lock switches, models without powershift transmission. HANDLE - control lever, loader, two button, declutch and differential lock switches, models with powershift transmission, not shown CONNECTOR - harness LOCK - four-pin PLUG - cavity, not used with Ref 1A ADHESIVE - Superbonder 4 0 9 , 1 ml. BOOT - control lever, models without clam control lever, see page 9-7 for boot used on models with clam control lever SCREW - machine, pan head Phillips, No. 10 NC x 3/4 inch NUT - U-type, No. 10 NC LEVER - control, loader lift and bucket control BRACKET - control lever to bellcrank BOLT - hex, full threads, 6 - 1 . 0 x 16 mm WASHER - flat, 9/32 x 5/8 x 1/16 inch WASHER - flat, 21/32 x 1-1/2 x 1/32 inch, use as a spacer BELLCRANK - control, loader lift-and bucket control BUSHING - flanged, bellcrank PIN - bellcrank to control lever bracket PIN - cotter, 1/8 x 1-3/4 inch RETAINER - bearing BEARING - ball, retainer . . ; BOLT - hex, full threads, 6 - 1 . 0 x 16 mm WASHER - flat, 9/32 x 7/8 x 3/32 inch, hardened J O I N T - b a l l , 3/8 inch NF NUT - hex, self-locking, 3/8 inch NC BOLT - hex, 3/8 NC x 1-3/4 inch WASHER - flat, 13/32 x 13/16 x 3/32 inch, hardened NUT - hex, 3/8 inch NC NUT - hex, 3/8 inch NF ROD - bucket control R O D - l i f t control BOOT - 1 / 2 inch rod, at loader valve PIN - clevis, special PIN - cotter, 3/32 x 3/4 inch VALVE ASSEMBLY - control, loader, two spool, parts list page 8-73 BOLT - hex, 10 - 1 . 5 x 40 mm . . . . . . . . WASHER - flat, 11 x 21 x 2.5.mm, hardened BOLT - hex, full threads, 6 - 1 .O x 20 mm WASHER - flat, 9/32 x 7/8 x 3/32 inch, hardened NUT - hex, 6 mm - 1 . 0 , class 10

REO'D. 1 1 1 1 1 UAR 1 1 1 1 1 3 3 1 1 2 .2 2 2 1 1 1 2 1 2 2 2 2 1 1 2 2 2 1 3 3 3 3 .3


9-4

34^

BT97N068

^^f36

580 Super L Series 2 Loader

9-5

Backhoe

LOADER CLAM CONTROL REF. 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 17A

PART NO. 297615A1 123815A1 170-104, 129914A1 225-14105 439-5436 143210A1 124243A.1 123493A1 413-632 495-21044 108088A1 133989A1 239306A1 103-1437 614-6016 495-11028 515-2295

18 19 20 21 .22 23 24 25 26 27 28 29

133617A1 195615A1 176311A1 108088A1 495-81184 102761A1 432-828 112382A1 425-116 413-632 231-1446 112380A1

4

,.

DESCRIPTION H A N D L E - c o n t r o l lever LATCH - clam lock SCREW - machine, pan head Phillips, No. 5 NC x 3/8 inch S P R I N G - l e a f , clam lock : NUT - hex, No. 5 NC PIN - headed, 1/4 x 2--1/4 inch. CAP - push,' 1/4 inch SPRING - torsion, latch • LEVER - control, loader clam BOLT - hex, 3/8 NC x 2 inch WASHER - flat, 7/16 x-1 x 5/64 inch . . . . . . : BUSHING - flanged, control lever SLEEVE-pivot ROD - control, clam RING - heavy section external retaining. No. 37 BOLT - hex, full threads, 6 - 1 . 0 x 16 mm WASHER - flat, 9/32 x 5/8 x 1/16 inch. CLAMP - P-type, 3/8 inch ID, clutch cutout control harness to control lever BOOT - control lever, clam BRACKET - control lever to bellcrank BELLCRANK - control, loader BUSHING - flanged, bellcrank WASHER - flat, 21/32 x 1-1/2 x 1/32 inch, use as a spacer PIN - bellcrank to control lever b r a c k e t . . PIN - cotter, 1/8 x 1-3/4 inch BELLCRANK - control, loader clam. NUT - hex, 3/8 inch NF BOLT - hex, 3/8 NC x 2 inch NUT - hex, self-locking, 3/8 inch NC RETAINER- bearing

REQ'D. 1 1 2 2 2 1 1 •••1 1 1 2 2 ^ -I 1 1 3 .3 1 1 .1 1 -2 1 2 2 • • -1 1 1 1 2


Bur 7-3350


9-6

T2)

X

( 3 4 A ^

%

OTA)

34)

136


9-7

LOADER CLAM CONTROL REF. 30 31 32 33 34 34A 35 ' 36 36A

PART NO. 614-6016 396-41028 140-107 131-623 213-126 495-11041 187438A1 D149288 D149287

37 38 39 40 41 42

432-612 425-116 132873A1 302966A1 LI 8337 292904A1 256347A1 258616A1 298176A1 345-133

Bur 7-3350

DESCRIPTION REQ'D. BOLT - hex, full threads, 6 - 1 . 0 x 16 mm WASHER - flat, 9/32 x 7/8 x 3/32 inch, hardened SCREW - machine, pan head Phillips, No. 10 NC x 3/4 inch . . N U T - U - t y p e , No. 10 NC CLEVIS - adjustable, 3/8 inch NF WASHER - flat, 13/32 x 13/16 x 1/16 inch, between clevis and bellcrank. ROD - control, clam, at loader valve PIN - clevis, special, upper PIN - clevis, special, 5/16 x 15/16 inch, hardened, clam control rod lower clevis PIN - cotter, 3/32 x 3/4 inch NUT - hex, 3/8 inch NF BOOT - 3/8 inch rod, at loader valve V A L V E ASSEMBLY - loader control, three-spool, parts list page 8-75 . . . STRAP - tie, 15 inch, if used HANDLE - control lever, two button, declutch and differential lock CONNECTOR - harness . . . LOCK - four-pin PLUG - cavity ADHESIVE - Superbonder 409i 1 ml UAR


9-8

BT97D057


9-9

LOADER S E L F - L E V E L I N G CONTROL REF. 1 2 3 4 5 6 ,: 7 : 8 9 10 11

PART NO. 137283A1 142404A1 193854AT D149287 432-612 425-115 213-125 139865A1 844-10020 128580A1 NSS A30881

12 13 14 15 . 16 17

LI 5401 D95096 124721A1 614-8025 895-11008 829-1408

Bur 7-3350

DESCRIPTION WASHER - wave, at upright, loader arm pivot CAM - self-leveling CABLE - bucket level PIN - clevis, special, 5/16 x 15/16 inch, hardened PIN - cotter, 3/32;x 3/4 inch NUT - hex, 5/16 inch NF CLEVIS - adjustable, 5/16 inch NF GUARD-cable BOLT - heavy hex flange, 1 0 - 1 . 5 x 2 0 mm ;ROD ASSEMBLY - bucket level ROD - bucket level WASHER - special, hardened, flat, used as shim between bearing and snap ring BEARING - pivot, self-aligning, 5/8 inch RING - retaining, 5/8 inch, shaft retaining, special SPRING-coil BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - flat, 9 X 17 x 1.6 mm NUT - hex, 8 mm - 1 . 2 5 , class JO

REQ'D. 1 1 • • • -1 2 .2 1 1 1 2 -T -1 3 2 2 .1 4 4 4


9-10


9-11

LOADER LIFT FRAME AND MOUNTING P A R T S LIFT CYLINDER, SUPPORT STRUT, RETURN-TO-DIG AND ANTIROLLBACK REF. 1 2 3

PART NO. 141324A1 D127542 100696A1

4 5 6 7 7A 8 9

109268A1 111522A1 119129A1 495-81282 181842A1 .800-44050 112366A2

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

219-55 128818A1 142524A1 614-6016 A62209 833-40406 D137363 193-1003 440-10616 128312A1 895-11010 242369A1 D121047 104824A1 ,118900A1

25. 26 27 28 29 30 31 32 33 34 35

113629A1 800-44040 : 182895A1 192815A1 103-3350 118901A1 800-44040 219^1 427-6088 432-612 495-11053

Bur 7-3350

DESCRIPTION REQ'D. FRAME - loader lift 1 BUSHING - loader frame pivot 4 BUSHING - bucket cylinder link pivot, no longer included with frame, purchase separately. 4 BUSHING - bucket mounting 4 SHAFT - loader lift frame pivot 1 PIN - lift cylinder pivot, closed end. 2 WASHER - flat, 2-1/16 x 3 x 3/32 inch. 4 WASHER - special, hardened,.install a minimum of one washer per side . . . UAR RING - external retaining. No. 30, 50 mm 6 CYLINDER ASSEMBLY - 83 (3-1/4) ID x 766 mm (30-1/8 inch) stroke, loader lift, parts list page 8-127 2 FITTING - grease, 90 degree, 1/8 P T x 27/32 inch 2 BRACKET - mounting, return-to-dig switch 1 COVER - return-to-dig switch 1 BOLT - hex, full threads, 6 - 1 . 0 x 16 mm . . 2 CLAMP - P-type 1 NUT-U-type, 6 m m - 1 . 0 2 SWITCH - return-to-dig 1 NUT - hex, with external tooth lock washer. No. 6 NC 2 SCREW - machine, pan Phillips, No. 6 NC x 1 inch 2 BOLT - hex flange, special, 10 x 15 mm 2 WASHER - flat, 11 x 20 x 2 mm 6 STRUT - support, loader frame, left-hand lift arm only . . . 1 GROMMET - support strut 1 PIN - lock, includes lanyard and hair pin 1 PIN - left-hand lift cylinder rod end and support strut, mounts in the loader lift frame with the tapered end towards the outside of the frame 1 PiN - 1 5 5 mm (6-1/8 inch) long, right-hand lift cylinder rod end 1 RING - external retaining. No. 40, pin retaining. . .4 ROD - antirollback, attaches to bucket cylinder link 1 PIN - antirollback rod to bucket cylinder link 1 RING - E-type, external retaining. No. 50 1 PIN - loader lift frame to loader bucket 2 RING - external retaining, No. 40, pin retaining 4 FITTING - grease, straight, 1/8 PT x 21/32 inch 2 PIN - clevis, 3/8 x 7/8 inch, hardened 1 PIN - cotter, 3/32 x 3/4 inch .1 WASHER - flat, 17/32 x 1-1/16 x 3/32 inch .1


9-12

.,5

@

BT97N070


9-13

LOADER FRAME B U C K E T LINKS AND B U C K E T CYLINDER LINKS REF. 1

. PART NO. 141471A1

2

141472A1

3 4 5 6 7 8 9 10 11 12

118901A1 800-44040 219-1 D121194 250851A1 614-8030 895-11008 892-11008 829-1408 139180A1

13

139235A1

14

139195A1

15 16 17 18 19 20

D151034 827-20190 D132076 896-11020 829-1420 113133A2

21 22 23

116339A1 800-44040 219-1

Bur 7-3350•

DESORIPTION LINK - bucket, left-hand, without mounting holes for bucket position pointer, used in production, for service order 141472A1 link, item 2 LINK - bucket, left-hand or right-hand, with mounting holes for bucket position pointer PIN - bucket links to loader bucket RING - external retaining. No. 40, pin retaining. | FITTING - grease, straight, 1/8 PT x 21/32 inch POINTER - bucket position, models without clam bucket POINTER - bucket position, models with clam bucket BOLT - hex, full threads, 8 - 1.25 x 30 mm WASHER - flat, 9 x 17 x 1.6 mm WASHER - lock, 8 mm N U T - h e x , 8 m m - 1.25, c l a s s i c LINK - bucket cylinder, outer right-hand and inner and outer left-hand, includes item 15 bushing LINK - bucket cylinder, inner right-hand, with extra hole for antirollback rod, includes item 15 bushing, models without clam bucket, see item-14 link for models with clam bucket LINK - bucket cylinder, inner right-hand, with extra hole for antirollback rod, includes item 15 bushing, models with clam bucket, see item 13 for models without clam bucket BUSHING - one per each link, items 12-14 BOLT - hex, 20 - 2.5 x 190 mm, class 10.9 BUSHING - spacer, cylinder links WASHER - flat, 22 x 37 x 4 mm, hardened NUT - hex, 20 mm - 2 . 5 , class 10 . . . . OYLINDER ASSEMBLY - 76 (3) ID x 522 mm (20-9/16 inch) stroke, " loader bucket, parts list page 8-129 PIN - bucket cylinder rod end RING - external retaining. No. 40, pin retaining FITTING - grease, straight, 1/8 PT x 21/32 inch

REQ'D. 1 1-2 2 4 2 1 1 2 2; 2 .2 3

1

1 1 4 4 8 4 2 2 4 2


9-14

580 Super L Series 2 l:oader Backhoe

9-15

L O A D E R L O N G LIP B U C K E T REF.

PART NO. 141473A1

1 2 3 3A 4 5 6 7 8 9

NSS D129264 112946A1 113457A1 20-21232 429-1012 828-20160 -, 142538A1 832-10420 896-11020

1 : j i '

Bur 7-3350

DESCRIPTION BUCKET ASSEMBLY - loader, without bucket teeth, order from Machinery Price List, 2083 mm (82 inch) wide BUCKET - loader BUSHING - bucket ear EDGE - cutting, center, 2083 mm (82 inch) bucket EDGE - cutting, weld-on, blade mounting BOLT - plow, 3/4 NC X 2 inch, grade 8 NUT - hex, 3/4 inch NC, grade 8 BOLT - hex, 20 - 2.5 x 160 mm, class 10.9 SPACER - chain hook . NUT - hex, self-locking, 20 mm - 2.5 WASHER - flat, 22 x 37 x 4 mm, hardened

REQ'D. 1 1 8 .1 1 10 10 2 2 2 4


9-16

580 iSuper L Series 2 Loader Backhoe

9-17

L O A D E R L O N G LIP B U C K E T S REF.

PART NO. 198539A1

1 2 3 4 5 6 7 8 9 10

NSS D129264 134844A1 185506A1 20-21232 429-1012 828-20160 142538A1 896-11020 832-10420

Bur 7-3350

DESCRIPTION BUCKET ASSEMBLY - loader, without bucket teeth, order from Machinery Price List, 2362 mm (93 inch) wide, if used . . BUCKET - loader BUSHING - bucket ear ,. EDGE - cutting, weld-on, blade mounting EDGE - cutting, bolt-on, 93 inch (2362 mm) bucket. BOLT - plow, 3/4 NG X 2 inch' grade 8. NUT - hex,,3/4 inch NC, grade 8 BOLT - hex, 20 - 2.5 x 160 mm, class 10.9 SPACER - chain hook WASHER - flat, 22 x 37 x 4 mm, hardened . . . . : ; NUT - hex^self-locking, 20 mm - 2.5

REQ'D.

-.

1 1 8 1 .1 .10 10 2 2 4 2


9-18

580 Super L Series 2 Loader Backhoe LOADER CLAM BUCKET REF.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26

PART NO. 185488A1 175156A1 NSS D31140 142300A1 20-21232 29-1012 844-10110 D51391 832-10410 219-1 175160A1 NSS D129264 121920A1 20-21032 29-1010 D51392 814-10090 895-11010 832-10410 D51393 814-10080 895-11010 832-10410 321-1708 321-1707 250851A1

Bur 7-3350

9-19

DESCRIPTION REQ'D. BUCKET ASSEMBLY - clam, order from Machinery Price List, 2083 mm (82 inch) wide 1 CLAM ASSEMBLY - bucket 1 CLAM-bucket 1 BUSHING - 25 mm (1 inch) long, clam pivot 4 EDGE - cutting, bucket 2 BOLT - plow, 3/4 NC X 2 inch, grade 8 20 NUT - hex, 3/4 inch NC, grade 8 20 BOLT - heavy hex flange, 10 - 1 . 5 x 110 mm 2 PIN - pivot, clam to blade 2 NUT - hex, self-locking, 10 mm - 1 . 5 2 FITTING - grease, straight, 1/8 PT x 21/32 inch 2 BLADE ASSEMBLY - clam bucket 1 BLADE-bucket 1 BUSHING - bucket ear 8 EDGE - cutting, blade 1 BOLT - plow, 5/8 NC X 2 inch, grade 8 10 NUT - hex, 5/8 inch NC, grade 8 10 PIN - cylinder mounting, upper 2 B O L T - h e x , 1 0 - 1 . 5 x 9 0 mm 2 WASHER - flat, 11 x 20 x 2 mm 2 NUT - hex, self-locking, 10 mm - 1 . 5 2 PIN - cylinder mounting, lower 2 BOLT - hex, 10 - 1 . 5 x 80 mm 2 WASHER - flat, 11 x 20 x 2 mm 2 NUT - hex, self-locking, 10 mm - 1 . 5 2 DECAL -0-2-4, clam bucket opening indicator 1 DECAL - clam bucket position 1 POINTER - bucket position, bolts to clam bucket link, see page 9-13 for link and mounting hardware 1


9-20

|-

BT97N076

f


9-21

LOADER VALVE GUARD REF. 1 2 3

.

PART NO. 238048A2 614-10025 896-11010

Bur 7-3350

DESCRIPTION GUARD - valve shield, if used B O L T - h e x , full threads, 1 0 - 1 . 5 x 2 5 mm , WASHER - flat, 11 x 21 x 2.5 mm, hardened

REQ'D. 1 2 2


9-22


9-23

TOOL QUICK C O U P L E R S REF.

PART NO.

DESCRIPTION

REQ'D.

*TOOL QUICK COUPLER, MANUAL 1

*191239A1

COUPLER - tool, loader, manual, used with D121194 bucket position pointer and 139235A1 right-hand bucket cylinder link, Ref 6 and 13 on page 9-13, if used

1

TOOL QUICK COUPLER, HYDRAULIC h292969A2

COUPLER - quick, tool, loader, hydraulic, component parts list not available at time of printing

1

* NOTE: Coupler comes complete, component parts are not serviced separately. + NOTE: See page 8-65 for hydraulic tool quick coupler hydraulics.

Bur 7-3350


9-24


9-25

BACKHOE CONTROL TOWER COVERS REF. 1 2

•PART NO; 128403A1 130480A1

2A

253394A1

3 4

128401A1 -130479A1

4A

277187A1

5

353-411

6 78 9 10 11 12 13 14 15

281-1878 281-18712 195-140 D149866 •D149867 136822A1 D149868 136824A1 140-106 131-623

DESCRIPTION REQ'D. COVER - rear, console, used on all models with foot swing COVER - console, front, used on models with foot swing, without auxiliary hydraulics COVER - console, front, used on models with foot swing, with auxiliary hydraulics COVER - console, rear, used on all models with hand swing COVER - front, console; used on models with hand swing, without auxiliary hydraulics COVER - console, front, used on models with hand swing] with auxiliary hydraulics PLUG - button, 1 inch, nylon, 1 used with 130479A1 console - 2 used with 130480A1 console cover 1-2 SCREW - self-tapping, hex washer head, 1/4 NC x 1/2 inch, lower .2 SCREW - self-tapping, hex washer head, 1/4 NC x 3/4 inch, upper 3 WASHER - flat, 9/32 x 5/8 x 1/16 inch 5 BOOT - used with 130480A1 console cover with 5 control levers BOOT - used with 130480A1 console cover with 6 control levers RETAINER - boot, used with items 9 and 10 BOOT - used with 13d479A1 console cover with 4 control levers RETAINER - boot, used with item 12 only SCREW - machine, pan head Phillips, No. 10 NC x 1/2 inch (4) used with 136822A1 retainer, (6) used with 136824A1 retainer 4-6 NUT - U-type, No. 10 NC (4) used with 136822A1 retainer, (6) used with 136824A1 retainer 4-6

MODELS WITH BACKHOE AUXILIARY HYDRAULICS 16 17 18 19

277184A2 281.-14716 299383A1 353-408

Bur 7-3350

BRACKET - control lever SCREW - self-tapping, hex washer head, 1/4 NC x 1 inch DECAL - backhoe auxiliary hydraulic control PLUG - button, 3/4 inch

.1 2 1 1


9-26

BT97N159


9-27

B A C K H O E C O N T R O L T O W E R S U P P O R T AND S E A L S REF. 1

PART NO. 185975A1

2 2A

180376A1 180402A1

2B 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 .. 18 19

'

300580A1 121519A1 614-10035 496-41041 179956A1 184696A1 , 814-10060 496-41041 182295A1 184695A1 614-8020 895-11008 892-11008 :232875A1 184694A1 614-6016 895-11006 892-11006

Bur 7-3350

DESCRIPTION SUPPORT -. backhoe control mounting, with 3 mounting holes in base for item 11 seal support bracket BRACKET - mounting, left-hand, 6 spool valve BRACKET - mounting, left-hand, 7 spool valve, without auxiliary hydraulics BRACKET - mounting, left-hand, 7 or 8 spool valve, with auxiliary hydraulics BRACKET - mounting, right-hand, valve mounting B O L T - h e x , full threads, 1 0 - 1 . 5 x 3 5 mm WASHER - flat, 13/32 x 1-1/8 x 9/64 inch, hardened MOUNT - console BRACKET - seal support, front BOLT - hex, 10 - 1 . 5 x 60 mm W A S H E R - f l a t , 13/32 x 1-1/8 x 9/64 inch, hardened SEAL - foam, control tower BRACKET - seal support, front BOLT - hex, full threads, 8 - 1.25 x 20 mm WASHER - flat, 9 x 17 x 1.6 mm WASHER - lock, 8 mm SEAL - noise reduction, backhoe valve rods BRACKET - seal support, rear BOLT - hex, full threads, 6 - 1 . 0 x 16 mm WASHER - flat, 6 . 6 x 1 2 x 1.6 mm WASHER - lock, 6 mm

REQ'D. 1 1 1 1 1 4 4 2 2 4 4 .1 1 3 2 -3 1 -1 4 2 4


9-28

.Ji-<19)


9-29

B A C K H O E C O N T R O L S WITH F O O T S W I N G WITH NON-EXTENDABLE DIPPER REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 , 31 32 33

PART NO. 129015A1 614-8025 832-10408 D59912 136267A1 136269A1 D148992 136263A1 D150397 425-118 136261A1 -D150435 D150434 L54563 A30881: D34666 . D150486 D148994 D148993 614-8025 832-10408 213-126 D14928.8 D150493 427-6088 432-612 425-156 189297A1 189296A1 189295A1 -189298A1 189294A1 189299A1

DESCRIPTION SHAFT - pivot, control levers. . BOLT - hex, full threads, 8 - 1.25 x 25 mm NUT - hex, self-locking, 8 mm - 1.25 KNOB - lever, stabilizer control levers LEVER - control, boom LEVER - control, bucket BUSHING - control lever, used with 136267A1 and 136269A1 control levers LEVER - control, dipper. • BELLCRANK - dipper control N U T - h e x , 1/2 inch NF . . . LEVER - control, stabilizer BELLCRANK - right-hand stabilizer c o n t r o l . . . BELLCRANK - left-hand stabilizer control KNOB - control lever, boom, dipper and bucket control levers WASHER - special, hardened, flat, used as a shim between control levers WASHER - flat, special, 3/4 inch, 3/4 inch, hardened, may be used in place of item 15 SPACER - control lever, not used on models with extendable dipper SHAFT - swing control BEARING - self-aligning, shaft BOLT - hex, full threads, 8 - 1.25 x 25 mm NUT - hex, self-locking, 8 mm - 1 . 2 5 . . CLEVIS - adjustable, 3/8 inch NF PIN - clevis, special CLEVIS - 3/8 inch, stabilizer control rod, special PIN - clevis, 3/8 x 7/8 inch, hardened PIN - cotter, 3/32 x.3/4 inch . ..: NUT - hex, jam, 3/8 inch NF ROD - left-hand stabilizer control ROD right-hand stabilizer control ROD dipper control ROD boom control ROD bucket control ROD - swing control.

REQ'D. 1 ... 1 1 2 .1 1 2 -1 1 • • • -3 - 2 1 1 3 UAR 1 1 -1 2 4 4 3 3 2 2 .5 6


Bur 7-3350


9-30

a

.Ji-<19)

9-31


BACKHOE CONTROLS WITH FOOT SWING WITH NON-EXTENDABLE DIPPER

REF. PART NO. 34 D149295 36 425-116 37 D149287 432-612 , 38 , 136271 A t 39 136270A1 40 . 219-1 41 42 .614-10025 44 832-10410 45 D150503 D149262 4647 425-156 . 48 D149288 49 432-612

Bur 7-3350

DESCRIPTION JOINT - ball, swing control rod to shaft NUT - hex, 3/8 inch NF PIN - clevis, special, 5/16 x 15/16 inch, hardened, rods to valve PIN - cotter, 3/32 x 3/4 inch . . .\ PEDAL - left-hand swing PEDAL - right-hand swing FITTING - grease, straight, 1/8 PTx 21/32 inch BOLT - hex, full threads, 10 -1.5 x 25 mm NUT - hex, self-locking, 10 mm - 1 . 5 . . ROD - with clevis, swing-pedal to cross shaft CLEVIS - special, swing pedal rod . NUT - hex, jam, 3/8 inch NF PIN - clevis, special, swing pedal rod PIN - cotter, 3/32 x 3/4 inch

REQ'D. .1 • • • -1 .6 . .6 1 . . . . . . . .1 2 . .4 4 2 .2 2 4 4


9-32

®

BT97N079

—

-

o

9-33


BACKHOE CONTROLS WITH FOOT SWING PARTS USED WITH EXTENDABLE DIPPER

REF. 1 2 3 4 5 6 7 8 9 , 10 11

PART NO. L54563 136263A1 425-118 182006A1 A3b881 213-126 427-6088 432-612 425-156 189293A1 D149287

Bur 7-3350

DESCRIPTION KNOB - control lever, extendahoe LEVER - control, extendahoe NUT-hex, 1/2 inch NF BELLCRANK - extendahoe control lever WASHER - special, hardened, flat, spacer CLEVIS - adjustable, 3/8 inch NF PIN - clevis, 3/8 x 7/8 inch, hardened PIN - cotter, 3/32 x 3/4 inch ; NUT - hex, jam, 3/8 inch NF ROD - extendahoe control lever to valve PIN - clevis, special, 5/16 x 15/16 inch, hardened, rod to valve . ,

REQ'D.

UAR


9-34

B9504119T


BACKHOE CONTROLS WITH HAND SWING

9-35

*UPPER CONTROL L E V E R S WITH NON-EXTENDABLE DIPPER REF. 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 : 20 21 22 23 24 25

26

PART N O . 108864A1 D148947 109131A1 109132A1 D59912 425-118 108924A1 108923A1 495-11081 P39118 125113A1 ld6989Al 125113A1 106990A1 425-1110 178006A1 178004A1 102765A1 432-^828 112380A1 614-6016 396-41028 614-6020 ^ 829-1406 A3088i

DESCRIPTION P L A T E - mounting, bearing and bellcrank S H A F T - pivot, stabilizer lever L E V E R - stabilizer, left-hand L E V E R - stabilizer, right-hand K N O B - lever, stabilizer levers

N U T - hex, 1/2 inch N F . : . . . - left-hand stabilizer lever - right-hand stabilizer lever W A S H E R - f l a t , 13/16 x 1-15/32 x 1/8 inch KNOB-control lever L E V E R - control, boom and swing B E L L C R A N K - left-hand boom and swing lever L E V E R - control, bucket and dipper B E L L C R A N K - right-hand bucket and dipper lever N U T - hex, 5/8 inch N F B E L L C R A N K - boom and swing control lever B E L L C R A N K - bucket and dipper control lever PIN'- bellcrank P I N - cotter, 1/8 x 1-3/4 inch R E T A I N E R - bearing B O L T - hex, full threads, 6 -1.0 x 16 mm W A S H E R - flat, 9/32 x 7/8 x 3/32 inch, hardened B O L T - hex, full threads, 6 --1.0 x 20 mm N U T - hex, 6 mm -1.0, class 10 W A S H E R - special; hardened BELLCRANK BELLCRANK

REQ'D.

- .1 1 1 1 2 .2 .1 , . .1 .1 .2 1 1 1 .1 .2 .1 1 2 2 4 2 2 6 6 : UAR

* NOTE: See page 9-37 for lower control levers.

Bur 7-3350


9-36

B9504120T


9-37

BACKHOE CONTROLS WITH HAND SWING *LOWER CONTROL LEVERS WITH NON-EXTENDABLE DIPPER REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

PART NO. 185981A1 185982A1 D149287 432-612 425-116 213-126, D149288 185977A1 D149295 185978A1 D136773 413-624 425-106 185979A1 185980A1 614-10025 832-10410 231-2446

DESCRIPTION ROD - stabilizer, right-hand stabilizer ROD - stabilizer, left-hand stabilizer . . PIN - clevis, special, 5/16 x 15/16 inch, hardened, rods toivalve PIN - cotter, 3/32 x 3/4 inch NUT-hex, 3/8 inch NF CLEVIS - adjustable, 3/8 inch NF . . . . . PIN - clevis, special. . . ROD - bucket control, JOINT - ball, control rod ROD - dipper control JOINT - ball, 3/8 inch NF, control rods BOLT - hex, 3/8 NC x 1-1/2 inch NUT- hex, 3/8 inch NC ROD - boom control ROD - swing control BOLT-hex, full threads, 1 0 - 1 . 5 x 2 5 mm NUT-hex, self-locking, 10 mm-1.5 NUT - hex, self-locking, 3/8 inch NF

REQ'D. 1 • • • -1 .6 8 ......6 2 2 1 -2 1 2 2 -2 1 1 .2 2 2

* NOTE: See page 9-35 for upper control levers.

Bur 7-3350

• Issued February, 1998

9-38

/ /11

[//

./.

EXCAVATOR CONTROL PATTERN O

BS97D060

Q

/

//7/

/ / /

9-39


BACKHOE CONTROLS

IN EXCAVATOR CONTROL PATTERN REF. 1 2 3 4 5

PARTNO. 245592A1 * 195030A2 * 195032A1 E49498 E49497 198410A1

DESCRIPTION KIT - excavator control pattern, purchase from Parts and Components ROD - dipper, replaces existing, boom control rod ROD - boom, replaces existing dipper control rod DECAL - control, right-hand DECAL - control, left-hand PLATE r excavator control pattern

REQ'D.

* NOTE: The right-hand control lever, which used to control the dipper, now controls the boom and the left-hand control lever, which used to control the boom, now controls the dipper. - NOTE: . The machine must be equipped with hand swing controls. If your machine is equipped with (Case) foot swing controls, the foot swing to hand swing controls field kit must be ordered and installed before installing this kit.

Bur 7-3350


9-40

i

(T2>

9-41

BACKHOE CONTROLS WITH HAND SWING PARTS USED WITH EXTENDABLE DIPPER

REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14

PART NO. 179029A1 126918A1 614-10025 832-10410 D143416 D134900 427-6088 432-612 425-156 185976A1 D149287 432-612 D150032 219-1

Bur 7-3350

DESCRIPTION PEDAL - extendahoe control, right-hand SUPPORT - pedal, with hole for tube and grease fitting BOLT - hex, full threads, 10 -1.5 x 25 mm NUT - hex, self-locking, 10 mm -1.5 RING - retaining, clip ring, special CLEVIS- special, 3/8 inch PIN - clevis, 3/8 x 7/8 inch, hardened PIN - cotter, 3/32x3/4 inch NUT - hex, jam, 3/8 inch NF ROD - extendahoe control PIN - clevis, special, 5/16 x 15/16 inch, hardened, rod to valve PIN - cotter, 3/32 x 3/4 inch TUBE-pedal lube FITTING - grease, straight, 1/8 PT x 21/32 inch

REQ'D. ,.1 1 2 .2 1 -1 1 1 1 1 1 1 1 1


9-42

BT97M212


9-43

BACKHOE AUXILIARY HYDRAULIC CONTROL LEVER REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18A 19 20

PART NO. 275820A3 D59912 275677A1 614-6025 829-1406 195-81013 D136635 103-3350 495-11053 283226A1 896-;11020 276070A1 495-81002 R47941 • 425-156259410A1 .129-289 25781OAI 283i332A1 895-18010 432-612

DESCRIPTION LEVER - auxiliary control, detent lever, backhoe, uni-directional flow, activates flow to the attachment through the use of the foot swjtch, see page 4-47 for foot switch KNOB - lever SHAFT - pivot, 7 or 8 spool BOLT- hex, full threads, 6-1.0 x 25 mm ;. NUT - hex, 6 mm -1.0, class 10 WASHER-flat, 33/64x7/8 1/32 inch, used as a shim BLOCK - shifter pivot RING - E-type, external retaining. No. 50 WASHER - flat, 17/32 x 1-1/16 x 3/32 inch SPRING - return WASHER - flat, 22 x 37 x 4 mm, hardened SHAFT - spring pivot WASHER - flat, 7/16x1 -3/8 x 5/64 inch JOINT - ball, male, 3/8 inch NF NUT - hex, jam, 3/8 inch NF . TURNBUCKLE - hex NUT - hex, jam, 3/8 inch NF, left-hand thread ROD - control, 7 spool valve . ROD- control, 8 spool valve WASHER-flat, 11 X 18x1.6 mm PIN - cotter, 3/32 X 3/4 inch

REQ'D. 1 1 1 2 2 3 1 2

NOTE: See pages 8-51 - 8-55 for backhoe auxiliary hydraulics, page 4-47 for backhoe auxiliary electrical circuit and page 9-25 for the backhoe control tower cover used with auxiliary hydraulics.

Bur 7-3350


9-44

- o

1'

B9504122T

I''

"

\l>


9-45

BACKHOE STABILIZERS, PLATES AND PADS REF. 1

PART NO. REF

2

REF

D38907 103-16175 D133428 D5014& 121665A1 103-16175 b26002 D25279 D88427 D28648 D143406 D25279 '•' D142519 D61368 D39256 413-1228 • .425-1012 186405A1 20 D142314 21 .231-4247 22 413-632 23 230-4216 24 189955A1 25 " D149033 190035A1 26 27 190967A1 28 190036A1 29 495-21044 30 230-4216 31 D143406 32 495-81282 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Bur 7-3350

DESCRIPTION CYLINDER ASSEMBLY -108 (4-1/4) ID x 553 mm (21-3/4 inch) stroke, stabilizer, right-hand, parts list page 8-133 CYLINDER ASSEMBLY - 108 (4-1/4) ID x 553 mm (21-3/4 inch) stroke, stabilizer, left-hand, parts list page 8-133 PIN - stabilizer cylinder to frame RING - heavy external retaining. No. 175, pin retaining LEG - stabilizer BUSHING - leg to frame PIN - stabilizer leg to, frame RING - heavy external retaining, No. 175, pin retaining PIN - stabilizer cylinder to leg . RING - snap, pin retaining PLATE - stabilizer, cleated, if used PIN - D88427 stabilizer plate to leg WASHER - flat, special, 1-17/32 x 2-23/64 x 1/8 inch, used as a spacer RING - snap, pin retaining PLATE - stabilizer, street or cemetery, if used PAD - rubber, if used PIN - 9-3/8 inch (238 mm) long, D142519 plate to leg BOLT - hex, 3/4 NC x 1-3/4 inch NUT - hex, 3/4 inch NC PLATE ASSEMBLY - stabilizer flip over, if used PAD - rubber NUT - hex, self-locking, 7/16 inch NC . . . BOLT - hex, 3/8 NC x 2 inch NUT - hex, self-locking, 3/8 inch NC PLATE - stabilizer, flip over PIN - 323.5 mm (12-3/4 inch) long, plate to stabilizer leg BOLT-J-type PAD - rubber, round PLATE-steel WASHER - flat, 7/16 x 1 x 5/64 inch NUT - hex, self-locking, 3/8 inch NC WASHER - flat, special, 1-17/32 x 2-23/64 x 1/8 inch, used as a spacer WASHER - flat, 2-1/16 x 3 x 3/32 inch

REQ'D. 1 1 2. .4 2 -2' -2 .4 2 4 -2 2 UAR 4 -2. 2 2 8 8 2 3 9 2 2 1 1 2 2 1 2 2 UAR UAR


9-46

-A I -^^^

V,


9-47

eio^CKHOE SWING CYLINDERS AND SWING TOWER REF. 1 2 3 4 5 6 7 8 9 10 11 12 12A 13 14 15 16 17 18 19 20 21 24 25 26 27 28 29 30 31 32 33 34 35

PART NO. 249867A1 191017A1 121778A1 D135741 ,0135557 D135559 .,•151073 D151074 135248A1 135249A1 REF

V

198976A'1 • 114318A1 827-20075 896-11020 829-1420 135247A1 495-81227 103-16200 243084A1 134167A1 D151065 D136392 D136700 D136391 800-40065 219-1 292385A1 219,-55 ; 800r40070 D149239 197718A1 293636A1 D144423

Bur 7-3350

DESCRIPTION REQ'D. TOWER ASSEMBLY- backhoe swing 1 BUSHING - boom cylinder pivot. . .2 , BUSHING - inner, boom pivot -2 BUSHING - outer, boom pivot 2 BUSHING - upper, swing tower pivot 1 BUSHING - upper, tower p i v o t . . . . 1 BUSHING - tower pivot . . . . 1 BUSHING - 70 X 86 x 28 mm long, lower 1 BUSHING - upper, swing cylinder pivot 2 BUSHING -Mower, swing cylinder pivot 2 CYLINDER ASSEMBLY -102 (4) ID X 292 mm (11-1/2 inch) stroke, swing, parts list page 8-135 . 2 BRACKET - swing cylinder to frame 1 BUSHING - 80 mm ID, cylinder pivot . . .2 BOLT - hex, 20 - 2.5 x 75 mm, class 10.9 6 WASHER - fiat, 22 x 37 x 4 mm, hardened. 12 NUT - hex, 20 mm - 2.5, class 10 6 PIN - swing cylinder rod end to swing tower .2 WASHER - flat, 2-1/16 x 2-15/16 x 1/16 inch 4 RING - heavy external retaining. No. 200, pin retaining 4 WASHER - bearing, special, 5 mm thick, swing tower . . . . : 1 SHIM - 2.05 mm (.08 inch) thick : . . . UAR PIN - lower, swing tower to frame, grease fitting mounts in top of pin 1 SHIM - 72 x 89 X 3.0 mm, upper UAR SHIM-67 X 83 x2.0 mm .2 S H I M - 7 2 x 8 9 x 1 6 mm. . . . . . UAR RING - external retaining. No. 65, pin retaining, lower 2 FITTING - grease, straight, 1/8 PT x 21/32 inch 1 PIN - swing tower to frame, upper 1 FITTING - grease, 9Q degree, 1/8 PT x 27/32 inch 1 RING - external retaining. No. 70, pin retaining 2 PIN - swing stop, without snap ring 1 SHIM - swing cylinder spacer, use as required between bracket and ear of main frame, shims may be required on one end or both ends of bracket, if used • • • • UAR WASHER - flat, upper 1 WASHER - 2-5/8 x 3-3/8 x 1/8 inch, used as a shim UAR


9-48

9-49


BACKHOE SWING TOWER AND BOOM REF. 1

PART NO. REF

2 3 4 5 6 7 8 9

121779A1. 219-1 604-20040 496-41081 122897A1 H71514 R32119 144200A1

10 11 12

122284A1 D151071 ,,•135739

13

D137218

14 15

D120450 REF

16 17 18 19 20 21 22 23 24 25 26 27 ^

D132494 219-1 300013A1 D136391 D136392 D133632 181042A1 123167A2 H433285 800-4155 123168A1 190313A1

DESCRIPTION SWING TOWER - backhoe, with inner ears, see page 9-47 for swing tower and bushings PIN - swing tower to boom FITTING - grease, straight, 1/8 PT x 21/32 inch BOLT - hex, self-locking, 20 - 2.5 x 40 mm WASHER - flat, 13/16 x 1-3/4 x 7/32 inch, hardened SPACER - 21 X 32 x'12 mm WASHER - special, boom to swing tower SHIM-71 (2-13/16) ID X 114 mm (4-1/2 inch) CYLINDER ASSEMBLY -127 (5) ID x 842 mm (33-5/32 inch) stroke, boom, parts list page 8-137 BOOM - backhoe, service replacement BUSHING - 70 (2-3/4) ID x 34 mm (1-5/16 inc) long . . . . BUSHING - 70.(2-3/4) ID x 44 mm (1-3/4 inch) long, with slot for groove pin, right-hand side of boom at boom to dipper pivot. . . BUSHING - 70 (2-3/4) ID x 44 mm (1-3/4 inch) long, without slot for groove pin, left-hand side of boom at boom to dipper pivot PLUG - plastic CYLINDER ASSEMBLY - 5 (127) ID x 23 inch (583 mm) stroke, dipper, parts list page 8-139 PIN - boom to dipper FITTING - grease, straight, 1/8 PT x 21/32 inch PIN - center groove, 1/2 x 3-1/4 inch, hardened SHIM - 72 X 89 x 1.6 mm, boom to dipper SHIM - 72 X 89 X 3.0 mm, boom to dipper WASHER - flat, hardened, special NUT - hex flange, special, 1-3/4 inch NF PIN - dipper cylinder to boom, with center lubrication groove SHIM - 5 7 x 7 6 X 1.5 mm RING - external retaining, No. 55, pin retaining PIN - boom cylinder closed end to boom PIN - boom cylinder rod end to swing tower

REQ'D. 1 2 2 2 . .2, 2 UAR UAR .1 1 2 .V 1 7 1 1 2 .1 UAR UAR 1 1 1 4 4 1 .1


Bur 7-3350


9-50

24) (25)


9-51

BACKHOE SWING TOWER AND BOOM REF. 28 29 30 31 32 33

PART NO. 103-11237 1233i8A1 D138022 495-81227 495-81226 103-16175

Bur 7-3350

DESCRIPTION RING - external retaining, No. 237, pin retaining WASHER - special, 62 mm ID PIN - clipper cylinder rod.end to dipper WASHER-flat, 2-1/16x2-15/16x1/16 inch WASHER - flat, 1-13/16 x 2-1/2 x 1/8 inch . .; RING - heavy external retaining. No. 175, pin retaining . . . . . . .

REQ'D. 2 UAR 1 UAR 2 2


9-52

BT97Nig5


9-53

BOOM LATCH REF. 1 . 3 4 5 . 6 7 8 9 10 11 12 13 14 15 16 17 . 18 19 20 21 22 23

PART NO. 122974A1 D129227; D144592 800-44040 D129641 614-10025 D143417 185632A2 D143723 614-10020 ' 892-11010 122958A1 D143591 D86664 122995A1 D143735 614-10050 122993A1 895-11010 829-1410 896-11012 219-55

Bur 7-3350

DESCRIPTION LATCH - backhoe boom PIN - boom latch to swing tower WASHER - flat, special RING - external retaining, No. 40, pin retaining CABLE - latch control BOLT - hex, full threads, 10 -1.5 x 25 mm SPACER -10 ID X 16 OD X 6 mm long ROD - boom latch control CLAMP - rod BOLT - hex, full threads, 10 -1.5 x 20 mm WASHER-lock, 10mm NUT - square, special, 10 mm - 1 . 5 . : RETAINER - clip ring BOOT-rod BUMPER-boom. , CLAMP-boot BOLT - hex, full threads, 10 -1.5 x 50 mm PLATE - boom stop WASHER-flat, 11 x 2 0 x 2 mm NUT - hex, 10 mm -1.5, class 10.9 WASHER - flat, 13.5 x 24 x 3 mm, hardened FITTING - grease, 90 degree, 1/8 PT x 27/32 inch

•••••

•••

REQ'D. 1 1 • -2 2 1 • •1 1 1 2 1 4 .1 -4 1 1 1 1 •• V 3 1 . . . .1 1


9-54

5

(30)

-(^f?^

I

(30

580 Super L Series 2 Loader BacUnoe

9-55

BACKHOE DIPPER AND B U C K E T REF. 1

PART NO. REF

2 3 4 5 6 7 8 9

D138022 495-81227 495-81226 103-16175 101631A1 NSS D120450 D140029 D138047

10

D150121

11

D127168 134437A1

12 13 14 15

NSS D127167 D127172 D150608

16 17

D150122 D150080

18 19 20 21 22 23 24 25 26 27 28

D127172 D138047 D141142 495-81282 D141164 103-16175 219-1 495-81226 D146288 103-16175 REF

DESCRIPTION REQ'D. CYLINDER ASSEMBLY - 80 (3-1/2) ID x 872 mm (34-5/16 inch) stroke, bucket, parts list page 8-141 1 PIN - bucket cylinder closed end to dipper 1 WASHER - flat, 2-1/16 x 2-15/16 x 1/16 inch UAR WASHER - flat, 1-13/16 x 2-1/2 x 1/8 inch 2 RING - heavy external retaining. No. 175, pin retaining 2 DIPPER ASSEMBLY - backhoe 1 DIPPER - backhoe 1 PLUG - plastic 6 BUSHING - 50 x 60 X 25.5 mm long 2 BUSHING - 54 mm (2-1/8 inch) long, dipper cylinder rod end, not included with dipper assembly, order separately 2 BUSHING - 70 ID X 36 mm long, not included with dipper assembly, order separately 2 BUSHING - 45 ID X 94 mm long, bucket coupler pivot, not included with dipper assembly, order separately 2 COUPLER ASSEMBLY - bucket, used with Ref 15 and 17 links, if used, see Ref 37 - 44 for optional coupler and links 1 COUPLER - backhoe bucket 1 BUSHING - 30 mm long, special, at dipper 2 BUSHING - 28 mm long, at bucket link 4 LINK - bucket guide, used with 134437A1 coupler, if used, see Ref 37 44 for optional coupler and links 2 BUSHING - 50 X 60 X 33 mm 2 LINK - bucket dump, with two bushings at forked end, used with 134437A1 coupler, if used, see Ref 37 - 44 for optional coupler and links 1 BUSHING-28 mm long 2 BUSHING - 54 mm (2-1/8 inch) long 2 PIN-306 mm long 2 WASHER - flat, 2-1/16 x 3 x 3/32 inch UAR SPACER -1-13/16 x 3 x 1/8 inch 4 RING - heavy external retaining. No. 175, pin retaining 4 FITTING - grease, straight, 1/8 PT x 21/32 inch 6 WASHER - flat, 1-13/16 x 2-1/2 x 1/8 inch 2 PIN - dump link to bucket coupler 1 RING - heavy external retaining. No. 175 2 BUCKET - backhoe, see pages 9-63 - 9-71 for bucket options 1 Continued on next page

Bur 7-3350


9-56

0. -(24) ~

0

0

BT97D063

39)(3]X^^

(29

(30)—•Pr-.T (30


9-57

BACKHOE DIPPER AND B U C K E T REF. ^ 29 30 31 32 33 34

PART NO. D37614 D143324 D25279 D149298 103-16175 D150619

35 36

495-81226 103-16175 281185A1

37 38 39 40, 41 42 43 44

NSS D127167 D127172 242562A1 D150122 242561A1 D127172 D138047

Bur 7-3350

REQ'D. DESCRIPTION PIN - bucket to coupler 1 WASHER - spacer, 38 x 64 x 2 mm 2 RING - snap, pin retaining 2 PIN - dipper to bucket, 305 mm (12 inch) Universal bucket only 1 RING - heavy external retaining. No. 175, pin retaining 2 PIN - dipper to bucket, all buckets except 12 inch (305 mm) buckets, for models with 12 inch bucket see item 32 pin .1 WASHER - flat, 1-13/16 x 2-1/2 x 1/8 inch UAR RING - heavy external retaining. No. 175, dipper to bucket pin 2 COUPLER ASSEMBLY - bucket, may replace 134437A1 (Ref 12) coupler on some models, used with Ref 40 and 42 links, if used 1 COUPLER - bucket, if used 1 BUSHING - 30 mm long, special, at dipper 2 BUSHING - 28 mm long, at bucket link .4 LINK - bucket guide, used with 281185A1 coupler, if used 2 BUSHING - 50 X 60 X 33 mm 2 LINK - bucket dump, used with 281185A1 coupler, if used.: 1 BUSHING - 28 mm long 2 BUSHING - 54 mm (2-1/8 inch) long 2


9-58

39)I^/^;^Xl4)

0

C>^
(42)£@

580 Super L Series 2 Loader Baclclioe

9-59

E X T E N D A B L E DIPPER REF. 1 2 3 4 5 6 7 8 9

PART N O . REF D132494 219-1 435-51652 D13639r D136392 D133632 181042Ai REF

10

REF

11 12 13 14

• D141666 495-81227 495-81226 103-16175 140453A1

15-. 16 17 18 19 20 2V 22 24 25 26 27 28

^'NSS

. D149079 D150121 102649A1 D127168 *134437A1 :

NSS

,

D127167 D127172 D133865 1340969C2 .300588A1 800-44040 D140247

29 30

A33509 *D150608

31 32

.D150122 *D150080

33 34

D127172 D138047

DESCRIPTION REQ'D. BOOM - backhoe, see page 9-49 for boom and bushings 1 PIN - boom to dipper 1 FITTING - grease, straight, 1/8 PT x 21/32 inch 2 PIN - center groove, 1/2 x 3-1/4 inch, hardened 1 SHIM - 72 x 89 X 1.6 mm, boom to dipper J 2;. SHIM - 72 X 89 x 3.0 mm; . . . .1 WASHER - flat, hardened, speciai".. .1 NUT - hex flange, .special, 1-3/4 inch NF. . . 1 CYLINDER ASSEMBLY - 5 (127) ID x 23 inch.(583 mm) stroke, dipper, parts list page 8-139 1 CYLINDER ASSEMBLY - 80 (3-1/2) ID x 872 mm (34-5/16 inch) stroke, bucket, parts list page 8-141 1 PIN - dipper and bucket cylinder to dippers ! 2 WASHER - flat, 2-1/16 x 2-15/16 x 1/16 inch UAR WASHER - flat, 1-13/16 x 2-1/2 x 1/8 inch 4 RING - heavy external retaining. No. 175, pin retaining 4 DIPPER ASSEMBLY - extension, inner, uses wear plates (Ref 52-54) with one mounting hole 1 DIPPER-inner 1 BUSHING - 50 X 34 mm long, dipper cylinder rod end pivot 2 BUSHING - 70 ID X 36 mm long, to dipper pivot 2 HOUSING - dipper, outer 1 BUSHING - 45 ID x 94 mm long, bucket coupler pivot 2 COUPLER ASSEMBLY - bucket, used with Ref 30 and 32 links, if used, see note 1 COUPLER - backhoe bucket . .1 BUSHING - 30 mm long, special, at dipper 2 BUSHING - 28 mm long, at bucket link 4 PLUG - plastic A CYLINDER ASSEMBLY - 76 (3) ID x 1068 mm (42 inch) stroke, dipper extension, parts list page 8-143.. .1 PIN - dipper extension cylinder closed end 1 RING - external retaining. No. 40, pin retaining .2 PIN - lock, used at dipper extension cylinder closed end when transporting only, used with item 29 lock pin ! 1 PIN - lock, 7/16 inch diameter 1 LINK - 33 mm wide bushing, bucket guide, used with 134437A1 coupler, if used, see note 2 BUSHING - 50 X 60 x 33 mm . . . . . . . .2 LINK - bucket dump, with two bushings at forked end, usediwith 134437A1 coupler, if used, see note 1 BUSHING - 28 mm long . . 2 BUSHING - 54 mm (2-1/8 inch) long 2

* NOTE: See page 9-57, Ref 37-44 for optional coupler and bucket links. Continued on next page

Bur 7-3350


9-60

3i;r3o

0

0

BT97N176

71


9-61

E X T E N D A B L E DIPPER REF. 35 37 38 39 40 : 41 42 48 49 50 52 53 54 55 56

PART NO. 219-1 D141142 495-81282 D141164 103-16175 219-1 495-81226 409-768 , D146288 103-16175 132716A1 132844A1 132842A1 183443A1 D143242

Bur 7-3350

DESCRIPTION FITTING - grease, straight, 1/8 PT x 21/32 inch PIN - 306 mm long, bucket cylinder rod end to links and links to dipper WASHER - flat, 2-1/16 x 3 x 3/32 inch SPACER-1-13/16x3x1/8 inch RING - heavy external retaining. No. 175, pin retaining FITTING - grease, straight, 1/8 PT x 21/32 inch WASHER-flat, 1-13/16 x 2-1/2 x 1/8 inch BOLT - hex serrated flange, 3/8 NC x 1/2 inch PIN - dump link to bucket coupler RING - heavy external retaining. No. 175 PLATE - wear, outer SHIM - 0.8 mm thick, wear plate SHIM -1.6 mm thick, wear plate PIN - pine tree, long RETAINER - push-in, plastic

REQ'D. 1 2 4 4 4 .5 2. .4 1 -2 4 UAR UAR 2 2


9-62

B9406079T

9-63

580 Super L Series 2 Loader Backhoe UNIVERSAL B A C K H O E B U C K E T 305 MM (12 INCH) WIDE REF.

PART NO.

DESCRIPTION

REQ'D.

305 MM (12 INCH) WIDE TRENCHING BUCKET AND TEETH - HEAVY DUTY 1 2 3 4

*D147418

5 6 7

D147411 D147410 D147409 D139851 D39093 245466A1 D138157

8 9 10 11 12

D139849 D51750 245466A1 D48212 D40243 D30933

B U C K E T A S S E M B L Y - heavy duty trenching, with 3 teeth, order from M a c h i n e r y Price List, 3 0 5 m m (12 inch) w i d e E D G E - cutting, right-hand side, bucket E D G E - cutting, left-hand side, bucket E D G E - c u t t i n g , center, 3 0 5 m m (12 inch) b u c k e t T O O T H A S S E M B L Y - outer corners POINT - tooth, outer corners P I N - flex, o u t e r p o i n t a n d s h a n k S H A N K - tooth, outer corners ^ T O O T H A S S E M B L Y - c e n t e r (order i t e m s 8-10) P O I N T - t o o t h , center . PIN - flex, c e n t e r point a n d s h a n k . S H A N K - tooth, center B U S H I N G - 1-3/4 x 2 - 1 / 4 x 3/4 inch . B U S H I N G - 1 - 1 / 2 X 1-7/8 X 1-1/4 i n c h

2 6

* N O T E : - S e e item 3 2 o n p a g e 9 - 5 7 for pin u s e d o n 12 inch U n i v e r s a l b u c k e t .

B u r 7^3350


9-64

c.

B9405166T

9^65


UNIVERSAL BACKHOE B U C K E T S 406 MM (16 INCH) AND 457 MM (18 INCH) WIDE REF.

PART NO.

DESCRIPTION

REQ'D.

406 MM (16 INCH) WIDE TRENCHING BUCKET AND TEETH - HEAVY DUTY 1

D147247

2 3 4

D146421 D146420 D147249 D139851 D39093 245466A1

5 6 7 8 9 10 11 12

D138157 D139849 D51750 245466A1 D48212 D37495 D30933

B U C K E T A S S E M B L Y - heavy duty trenching, with 3 teeth, order from M a c h i n e r y Price List, 4 0 6 m m (16 inch) w i d e , not s h o w n .1 E D G E - cutting, right-hand side, bucket E D G E - c u t t i n g , left-hand s i d e , b u c k e t E D G E - cutting, center, 4 0 6 m m (16 inch) bucket T O O T H A S S E M B L Y - outer corners POINT - tooth, outer corners PIN - flex, o u t e r point a n d s h a n k S H A N K - tooth, outer corners T O O T H A S S E M B L Y - c e n t e r (order items 8-10) P O I N T - tooth, center PIN - flex, c e n t e r point a n d s h a n k S H A N K - tooth, center B U S H I N G - 1-3/4 x 2-1/2 x 1-1/4 inch . B U S H I N G - 1 - 1 / 2 x 1 - 7 / 8 x 1-1/4 inch

2 -6


D146588

2 3 4

D146421 D146420 D145060 D139851 D39093 245466A1 D138157 D139849 D51750 245466A1 D48212

5 6 7 8 9 10 11 12

D37495 D30933

Bur 7 - 3 3 5 0

B U C K E T A S S E M B L Y - heavy duty trenching, with 4 teeth, order from M a c h i n e r y Price List, 4 5 7 m m (18 inch) w i d e E D G E - cutting, right-hand side, bucket E D G E - cutting, left-hand side, bucket E D G E - c u t t i n g , center, 4 5 7 m m (18 inch) b u c k e t T O O T H A S S E M B L Y - outer corners POINT - tooth, outer corners P I N - flex, outer p o i n t a n d s h a n k S H A N K - tooth, outer corners T O O T H A S S E M B L Y - c e n t e r (order i t e m s 8-10) P O I N T - t o o t h , center PIN - flex, c e n t e r point a n d s h a n k . . S H A N K - t o o t h , center . . B U S H I N G - 1-3/4 x 2-1/2 x 1 -1/4 inch B U S H I N G - 1-1/2 X 1-7/8 x 1-1/4 inch

2 6


9-66

&

B9406055T

9-67


UNIVERSAL BACKHOE B U C K E T S 610 MM (24 INCH) AND 762 MM (30 INCH) WIDE REF.

PART NO.

DESCRIPTION

REQ'D.


D150348

2 3 4 5 6 7

D146421 D146420 D142012 D139851 D39093 245466A1 D138157

8 9 10 11 12

0139849 D51750 245466A1 D48212 D37495 D30933

B U C K E T A S S E M B L Y - heavy duty trenching, with 5 teeth, order from M a c h i n e r y Price List, 6 1 0 m m (24 inch) w i d e E D G E - cutting, right-hand side, bucket E D G E - cutting, left-hand side, bucket E D G E - cutting, center, 6 1 0 m m (24 inch) bucket T O O T H A S S E M B L Y - outer corners P O I N T - tooth, outer corners PIN - flex, outer point a n d s h a n k S H A N K - tooth, outer corners T O O T H A S S E M B L Y - c e n t e r (order i t e m s 8-10) P O I N T - tooth, center PIN - flex, c e n t e r point a n d s h a n k S H A N K - tooth, center B U S H I N G - 1-3/4 x 2-1/2 x 1-1/4 inch B U S H I N G - 1 - 1 / 2 x 1-7/8 x 1-1/4 inch

3

2 6

762 MM (30 INCH) WIDE TRENCHING BUCKET AND TEETH - HEAVY DUTY 1 2 3 4 5 6 7 8 9 10 11 12

D150364 D146421 D146420 D145061 D139851 D39093 245466A1 - D138157 D139849 D51750 ,245466A1 'D48212 D37495 D30933

Bur 7 - 3 3 5 0

B U C K E T A S S E M B L Y - h e a v y d u t y t r e n c h i n g , with 5 t e e t h , o r d e r f r o m M a c h i n e r y Price List, 7 6 2 m m (30 inch) w i d e , not s h o w n E D G E - cutting, right-hand side, bucket E D G E - cutting, left-hand side, bucket E D G E - c u t t i n g , c e n t e r , 7 6 2 m m ( 3 0 inch) b u c k e t T O O T H A S S E M B L Y - outer corners POINT - tooth, outer corners PIN - flex, o u t e r point a n d s h a n k S H A N K - tooth, outer corners T O O T H A S S E M B L Y - c e n t e r (order i t e m s 8-10) P O I N T - tooth, center PIN - flex, c e n t e r point a n d s h a n k S H A N K - tooth, center B U S H I N G - 1-3/4 x 2-1/2 x 1-1/4 inch B U S H I N G - 1-1/2 x 1-7/8 x 1-1/4 inch

.2 6


9-68

B9406053T

9-69

580 Super L Series 2 Loader Backhoe UNIVERSAL B A C K H O E B U C K E T S 914 MM (36 INCH) WIDE REF.

PART NO.

DESCRIPTION

REQ'D.

914 MM (36 INCH) WIDE TRENCHING BUCKETS AND TEETH - HEAVY DUTY 1

D150365

2 3 4

D146421

5 6 7 8 9 10 11 12

D146420 D145062 D139851 D39093 245466A1 D138157 D139849 * D51750 245466A1 D48212 D37495 D30933

Bur7-3350

B U C K E T A S S E M B L Y - heavy duty trenching, with 7 teeth, order from M a c h i n e r y Price List, 9 1 4 m m (36 inch) w i d e E D G E - cutting, right-hand side, bucket. . . ! E D G E - c u t t i n g , left-hand s i d e , b u c k e t E D G E - c u t t i n g , center, 9 1 4 m m (36 inch) b u c k e t T O O T H A S S E M B L Y - outer corners P O I N T - t o o t h , outer c o r n e r s P I N - flex, o u t e r p o i n t a n d s h a n k S H A N K - t o o t h , outer corners T O O T H A S S E M B L Y - c e n t e r (order i t e m s 8 - 1 0 ) POINT - tooth, center PIN - flex, center point a n d s h a n k S H A N K - t o o t h , center B U S H I N G - 1-3/4 x 2-1/2 x 1-1/4 inch B U S H I N G - 1-1/2 X 1-7/8 x 1-1/4 inch

2 6


9-70

9-71


UNIVERSAL BACKHOE B U C K E T 610 MM (24 INCH) AND 762 MM (30 INCH) WIDE REF.

PART NO.

DESCRIPTION

REQ'D.

610 MM (24 INCH) WIDE - HIGH CAPACITY TRENCHING BUCKET 1

141232A1

2 3 4 5 6 7

141234A1 141233A1 D142012 D139851 D39093 24'5466A1 D138157

8 9 10 11 12

D139849 D51750 245466A1 D48212 D37495 D30933

762 Mr 1

190267A1

2

141234A1 141233A1

3 4 5 6 7 8 9 10 11 12

D145061 D139851 D39093 245466A1 D138157 D139849 D51750 245466A1 D48212 D37495 D30933

Bur 7 - 3 3 5 0

B U C K E T A S S E M B L Y - high c a p a c i t y t r e n c h i n g , w i t h 5 t e e t h , o r d e r f r o m M a c h i n e r y Price List, 6 1 0 m m ( 2 4 inch) w i d e E D G E - cutting, right-hand side, bucket E D G E - cutting, left-hand side, bucket E D G E - c u t t i n g , center, 6 1 0 m m ( 2 4 i n c h ) b u c k e t T O O T H A S S E M B L Y - outer corners POINT - tooth, outer corners P I N - flex, o u t e r p o i n t a n d s h a n k S H A N K - t o o t h , outer corners T O O T H A S S E M B L Y - c e n t e r (order i t e m s 8-10) POINT - tooth, center PIN - flex, c e n t e r point a n d s h a n k S H A N K - tooth, center B U S H I N G - 1 - 3 / 4 X 2-1/2 x 1-1/4 inch

2

B U S H I N G - 1 - 1 / 2 X 1-7/8 x 1-1/4 inch

6

0 INCH) WIDE - HIGH CAPACITY TRENCHING BUCKET B U C K E T A S S E M B L Y - high c a p a c i t y t r e n c h i n g , w i t h 5 t e e t h , o r d e r f r o m M a c h i n e r y Price List, 7 6 2 m m ( 3 0 inch) w i d e E D G E - cutting, right-hand side, bucket E D G E - cutting, left-hand side, bucket : E D G E - c u t t i n g , c e n t e r , 7 6 2 m m ( 3 0 inch) b u c k e t T O O T H A S S E M B L Y - outer corners P O I N T - t o o t h , outfer c o r n e r s . . P I N - flex, o u t e r p o i n t a n d s h a n k S H A N K - tooth, outer corners T O O T H A S S E M B L Y - c e n t e r ( o r d e r i t e m s 8-10) POINT - tooth, center P I N - flex, c e n t e r p o i n t a n d s h a n k S H A N K - tooth, center B U S H I N G - 1-3/4 X 2-1/2 x 1-1/4 inch B U S H I N G - 1 - 1 / 2 X 1-7/8 x 1-1/4 inch

2 6


9-72

B9411200T


9-73

F R O S T POINT A S S E M B L Y REF. 1 2 3 4 5 6 7

PART NO. D140679 NSS D37495 D83306 D43417 D54218 495-81292 D25279

Bur 7-3350

DESCRIPTION P O I N T A S S E M B L Y - frost, b a c k h o e B O D Y - frost point B U S H I N G - 1-3/4 X 2 - 1 / 2 X 1-1/4 inch POINT - tooth P I N - t o o t h point P I N - link, to frost point W A S H E R - flat, 1-9/16 x 3-1/4 x 3/16 inch RING - snap

. ;

REQ'D. 1 1 .2 1 1 1 2 2


9-74


9-75

FRONT COUNTERWEIGHT REF. 1 2 3 4

PART NO. 194520A1 827-20170 896-11020 829-1420

DESCRIPTION C O U N T E R W E I G H T - front, 2 0 0 kg (441 lbs), if u s e d B O L T - h e x , 2 0 - 2.5 x 1 7 0 m m , c l a s s 1 0 . 9 W A S H E R - flat, 2 2 x 3 7 x 4 m m , h a r d e n e d N U T - hex, 2 0 m m - 2.5, c l a s s 10

REQ'D. -1 .2 4 2

5 6 7 8

230513A1 827-20170 896-11020 829-1420

C O U N T E R W E I G H T - front, 4 0 8 kg ( 9 0 0 lbs), if u s e d B O L T - hex, 2 0 - 2.5 x 1 7 0 m m , c l a s s 1 0 . 9 W A S H E R - f l a t , 2 2 x 3 7 x 4 mm, hardened N U T - h e x , 2 0 m m - 2.5, c l a s s 10

1 2 4 2

Bur 7-3350


9-76

20)

\ _ (22)

580 Super L Series 2 Loader Backhoe C H A S S I S AND O P E R A T O R COMPARTMENT POD MOUNTS REF.

PART NO.

DESCRIPTION

9-77

REQ'D.

CHASSIS 1 2 3 4 5 6 7 8 8A 9

299395A1 180427A1 D127542 192559A1 D151069 0151070 220413A1 107124A1 185356A1 219-55

C H A S S I S - l o a d e r b a c k h o e , integral B U S H I N G - l o a d e r f r a m e pivot B U S H I N G - front a x l e pivot B U S H I N G - 80 m m ID, swing cylinder p i v o t . . B U S H I N G - 70 m n i ID, upper, backhoe frame, swing tower mounting

1 -2 2 2 1

B U S H I N G - 7 0 m m ID, lower, backhoe frame, swing tower mounting S P A C E R - 9 3 X 135 X 5 m m , b e a r i n g , w e l d s t o f r a m e B U S H I N G - lower, s i d e , b a c k h o e f r a m e , at stabilizer leg m o u n t i n g B O S S - 1 0 m m , welded to chassis frame F I T T I N G - g r e a s e , 9 0 d e g r e e , 1/8 P T x 2 7 / 3 2 i n c h , l o a d e r f r a m e pivot.

1 1 .4 7 2

OPERATOR COMPARTMENT POD MOUNTS 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

827-16110 495-81259 D138565 186977A1 829-1416 141249A1 627-12030 896-11012 827-16110 495-81259 186977A1 D138565 829-1416 180578A1 A14145.1 186977A1 829-1416

Bur 7-3350

B O L T - h e x , 16 - 2^0 x 1 1 0 m m , c l a s s 10.9 W A S H E R - flat, 2 1 / 3 2 x 2 x 1/4 inch . I N S U L A T O R - m o u n t i n g , f r a m e , u p p e r , firewall W A S H E R - f l a t , special N U T - h e x , 16 m m - 2 . 0 , c l a s s 1 0 B R A C K E T - mounting, frame, right-hand a n d left-hand B O L T - h e x , full t h r e a d s , 1 2 - 1.75 x 3 0 m m , c l a s s 1 0 . 9 W A S H E R - flat, 13.5 x 2 4 x 3 m m , h a r d e n e d B O L T - h e x , 16 - 2 . 0 x 1 1 0 m m , c l a s s 10.9 W A S H E R - flat, 2 1 / 3 2 x 2 x 1/4 inch W A S H E R - flat, s p e c i a l I N S U L A T O R - m o u n t i n g , f r a m e , lower, f r o n t N U T - h e x , 16 m m - 2 . 0 , c l a s s 10 BOLT-special M O U N T - rubber, f r a m e , rear W A S H E R - flat, s p e c i a l N U T - h e x , 16 m m - 2 . 0 , c l a s s 10

1 1 2 1 1 .2 4 4 .2 2 4 4. 2 2 2 2 2


9-78

32)(33)

S2.

580 Super L Series 2 Loader Backhoe B A T T E R Y BOX, HYDRAULIC OIL TANK AND RIGHT-HAND STEP REF. 1 1A IB 2 3 3A 4 5 6 7 8 12 13 14 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

PART NO. 283325A3 230857A1 440-1066 627-20040 302358A1 896-11020 185926A1 217-436 231656A1 614-10025 495-21044 218-5211 237-6010 138595A1 217-347 237-6006 214-1406 143218A1 143219A1 217-380 217-1102 120943A1 122603A1 , 121856A1 188008A2 *191047A1 614-8016 895-15008 814-10045 892-11010 D138055 120303A1 829-1410

DESCRIPTION TANK - hydraulic oil, right-hand side of chassis SCREEN - strainer, fill tube SCREW - machine, pan Phillips, No. 6 NC x 3/8 inch . BOLT - hex, full threads, 20 - 2.5 x 40 mm, class 10.9 WASHER - flat, hardened, special, right-hand side of tank. WASHER - fiat, 22 x 37 x 4 mm, hardened, left-hand side of tank SPACER - bushing, right-hand side of tank PLUG - hex socket headless, 3/8 inch PT, if used COVER - battery, 3 mm thick BOLT - hex, full threads, 10 -1.5 x 25 mm WASHER-flat, 7/16x1 x 5/64 inch PLUG - hex socket, 7/8-14 inch 0-ring boss, drain 0-RING - 3/4 ID X 3/32 inch wide CAP - hydraulic oil tank, nonvented ELBOW - 90 degree, 3/8 stem end x 9/16-18 inch adj 0-ring boss. 0-RING -15/32 ID x 5/64 inch wide CLAMP - adj, 7/16 - 25/32 inch dia HOSE - 9.5 (3/8) x 15 (19/32) x 735 mm (28-15/16 inch) long, vent GUARD - hose sleeve ADAPTER - straight, 3/8 inch stem end x PT . COUPLING - pipe, 3/8 inch . BREATHER - pressure vacuum, hydraulic oil tank BRACKET - breather mounting BOLT - hex washer, special, 10 -1.5 x 30 mm COVER - right-hand loader lift frame tubing, mounted above hydraulic oil tank TRIM - edge, 315 mm (12-13/32 inch) long BOLT - hex, full threads, 8 -1.25 x 16 mm WASHER - flat, 9 x 20 x 1.6 mm BOLT - hex, 10 - 1.5 x 45 mm WASHER - lock, 10 mm CLAMP-tube SPACER - clamp. NUT - hex, 10 mm -1.5, class 10.9

9-79

REQ'D. 1 1 2 4 2 2 2

*NdTE: Apply 75 mm (3 inch) of trim to front lower edge and 240 mm (9-7/16 inch) of trim to outside lower edge of cover. Continued on next page

Bur 7.3350


9-80

BT97N170


9-81

B A T T E R Y BOX, HYDRAULIC OIL TANK AND RIGHT-HAND STEP REF. 35 36

PART NO. B17576 226456A1

37 38 39 40 41 42 43

D40442 284223A1 811-10070 280164A1 832-10410 D40442 D55216

DESCRIPTION SEALANT - gasket, RTV No. 595, clear, 300 ml tube GAUGE ASSEMBLY - sight, hydraulic oil, full/cold lettering, aluminum, includes two hollow head bolts and four O-rings which are not serviced separately, used with Ref 35 sealant TRIM - edge, 305 mm (12 inch) long, cut from F42827 bulk trim BOX-tool BOLT - carriage, 10 - 1.5 x 70 mm PLATE - mounting NUT - hex, self-locking, 10 mm -1.5 TRIM - edge, 305 mm (12 inch) long, cut from F42827 bulk trim PAD - anti-skid, 2 x 9 inch

F42827


Bur 7-3350

REQ'D. 1 1 1 1 4 2 4 .1 1 UAR


9-82


9-83

RADIATOR WRAPPER REF. 1 2 3 4 5 6 7 8 9 10 11 12 13

PART NO. 139494A2 440-11010 109879A1 231-14109 176952A1 176957A1 614-10020 614-10035 K691987 D132895 D146035 614-20040 829-1420

DESCRIPTION SHROUD - radiator wrapper SCREW-machine, pan Phillips, No. 10 NC X 5/8 inch SPACER - plastic, hood NUT - hex, self-locking, No. 10 NC BRACKET - right-hand upper radiator mounting to shroud BRACKET - left-hand, upper radiator mounting to shroud BOLT -hex, full threads, 1 0 - 1 . 5 x 2 0 mm BOLT - hex, full threads, 10 - 1.5 x 35 mm WASHER - flat, special GROMMET - upper radiator to shroud mounting SPACER - upper radiator to shroud BOLT-hex, full threads, 2 0 - 2 . 5 x 4 0 mm NUT - hex, 20 mm - 2.5, class 10

REQ'D. 1 4 4 4 1 1 2 2 • .4 2 2 4 4

NOTE: See page 2-3 for radiator mounting parts.

Bur 7-3350


9-84

«r ^ I 1/

/

^^^^

//

^1)

BT97N088

.5>

580 Super L Series 2 Loader Backhoe PUMP GUARD REF. 1 2

PART NO. 229676A1 121856A1

Bur 7-3350

DESCRIPTION GUARD - pump, plate BOLT-hex washer, special, 10 -1.5 X 30 mm

9-85

REQ'D. 1 2


9-86

580 Super L Series 2 Loader Backhoe B A F F L E P L A T E AND S E A L S WITHOUT AIR CONDITIONING REF. 1 2 3 4 5

9-87

PART NO. 277502A1 121856A1 245450A1 277664A1 185493A1

DESCRIPTION PLATE - baffle, if used BOLT - hex washer, special, 10 -1.5 x 30 mm TRIM - edge, 571 mm (22-1/2 inch) long TRIM - edge, 575 mm (22-5/8 inch) long TRIM - edge, 160 mm (6-5/16 inch) long, cut from 137315A1 bulk trim

137315A1


Bur 7-3350

REQ'D. 1 2 . . . . . . .1 1 2 1


9-88

580 Super L Series 2 Loader Backiioe B A F F L E P L A T E AND S E A L S WITH AIR CONDITIONING REF. 1 2 3 4 5 6 7 8

9-89

PART NO 245011A1 121856A1 305690A1 245450A1 246063A1 246064A1 185493A1 D36179

DESCRIPTION PLATE - baffle, if used BOLT - hex washer, special, 10 -1.5 x 30 mm SEAL - foam, adhesive-backed TRIM - edge, 571 mm (22-1/2 inch) long. TRIM - edge, 170 mm (6-11/16 inch) long, cut from 233749A1 bulk trim TRIM - edge, 365 mm (14-3/8 inch) long, cut from 233749AH bulk trim TRIM - edge, 160 mm (6-5/16 inch) long, cut from 137315Al bulk trim TRIM - edge, 108 mm (4-1/2 inch) long, cut from F42827 bulk trim

F42827


1

137315A1


1

233749A1

TRIM - edge, bulk, 76200 mm (3000 inch or 250 feet) long

1

Bur 7-3350

REQ'D. 1 2 1 1 1 .1 2 1


9-90

9-91

ENGINE SIDE P A N E L S REF. 1 2 3 4 5 6 6A 7 8 9 10 11 12 13 14 15 16 17 - 18 19 20 21 22. 23 24 25 27 28 29 30 31 32 33 34 35 36 37 38

PART NO. 233523A1 233522A1 139492A1 139490A1 614^10025 895-11010 825-2410 183168A1 D143715 D143714 614-10025 895-11010 832-10410 121856A1 896-11010 139835AT 814-12110 896-15012 140428A1 139834A1 896-15012 829-1412 614-10025 895-11010 144908A1 D143417 825-2410 614-10025 895-11010 D143417 829-1410 D140267 495-11106 896-11012 234923A1 244441A1 297837A1 297836A1

Bur 7-3350

DESCRIPTION REQ'D. PANEL - engine, left-hand side, with grille 1 PANEL - engine, right-hand side, with grille . 1 BRACE - side panel, left-hand -1 BRACE - side panel, right-hand, not shown 1 BOLT - hex, full threads, 10 -1.5 x 25 mm 8 WASHER-flat, 11 x 20 x 2 mm 8 NUT - hex flange, 10 mm - 1.5 4 HANDLE - side panel, left-hand 1 BRACKET - side panel, left-hand .1 BRACKET - side panel, right-hand, not shown I. . . ; 1 BOLT-hex, full threads, 10- 1.5x25 mm : . .4 WASHER - flat, 11 x 20 x 2 mm 8 NUT - hex, self-locking, 10 mm -1.5 4 BOLT - hex washer, special, 10 -1.5 x 30 mm 4 WASHER - flat, 1 1 x 2 1 x 2 . 5 mm, hardened 4 PLATE-pivot, left-hand 1 BOLT - hex, 12 - 1.75 x 110 mm .2 WASHER - flat, 13.5 x 28 x 4 mm, hardened .2 TUBE-pivot 2 PLATE - pivot, right-hand 1 WASHER - flat, 13.5 x 28 x 4 mm, hardened 2 NUT - hex, 12 mm -1.75, class 10 2 BOLT - hex, full threads, 10 -1.5 x 25 mm 1 WASHER - flat, 11 x 20 x 2 mm . 1 CABLE - hood retaining 1 SPACER -10 ID x 16 OD X 6 mm long, cable. .1 NUT - hex flange, 10 mm -1.5 1 BOLT - hex, full threads, 10 -1.5 x 25 mm 1 WASHER-flat, 11 x 2 0 x 2 mm 1 SPACER -10 ID x 16 OD X 6 mm long, cable 1 NUT - hex, 10 mm -1.5, class 10.9 1 PLUG -side panel. 2 WASHER - flat, 1-1/16 x 2 x 1/8 inch .2 WASHER - flat, 13.5 x 24 x 3 mm, hardened 2 TRIM -150 mm (5-29/32 inch) long, used on models with air conditioning 2 TRIM - 700 mm (27-9/16 inch) long, used on models with air conditioning 2 PANEL - noise reduction, insulation, left-hand side. 1 PANEL - noise reduction, insulation, right-hand side, not shown 1


9-92

BT97N169

580 Super L Series 2 Loader Backiioe

9-93

TILT HOOD, UPRIGHT COVER, G R I L L E UNIT AND CHAFF SCREEN REF. 1 2, 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

PART NO. 139486A2 175599A1 614-10025 895-11010 829-1410 895-11010 139362A1 114980A1 139363A1 F44883 292785A1 440-11012 109879A1 185325A1 231-.14109 614-10025 895-11010 121856A1 825-2410 139502A1 .244287A1 139500A1 244286A1 229398A2 233262A1 253889A1 255447A1 257381A1 257382A1 255687A1 140-107 185325A1 187389A1 353-402 234923A1 246228A1

Bur 7-3350

DESCRIPTION HOOD - engine, tilt LATCH-hood BOLT - hex, full threads, 10 -1.5 x 25 mm WASHER - flat, 11 X 20 X 2 mm NUT - hex, 10 mm -1.5, class 10.9 WASHER - flat, 11 x 20 x 2 mm STUD- upper ball, 10 mm-1.5 CYLINDER - spring, counterbalance, hood STUD-lower ball. RETAINER - lock, ball stud retainer COVER - chassis upright, with turbocharged engine SCREW - machine, pan Phillips, No. 10 NC x 3/4 inch SPACER - plastic, hood spacer WASHER - spacer NUT - hex, self-locking. No. 10 NC BOLT-hex, full threads, 10- 1.5x25 mm WASHER - flat, 11 x 20 x 2 mm BQLT- hex washer, special, 10 -1.5 x 30 mm NUT-hex flange, 1 0 m m - i . 5 . BUMPER - grille, left-hand upper BUMPER - grille, left-hand lower. BUMPER - grille, right-hand upper BUMPER - grille, right-hand lower GRILLE - radiator shroud, see page 9-157 for Case emblem SEAL - foam, adhesive-backed, 20 (25/32) x 596 (23-15/32) x 6 mm (1/4 inch), with or without air conditioning, if used SCREEN-chaff INSERT - threaded, 1/4 inch, if used . BOLT - hex, 1/4 NC x 3/4 inch, if used WASHER - flat, 1/4 inch, if used INSERT - threaded, No. 10, if used SCREW - machine, pan head Phillips, No. 10 NC x 3/4 inch, if used WASHER - spacer, flat, No. 10, if used PANEL - noise reduction, insulation PLUG - button, 3/8 inch, models without windshield washer, if used TRIM -150 mm (5-29/32 inch) long,.hdod, if used TRIM - 1040 mm (41 inch) long, hood, if used

REQ'D. 1 1 10 .14 8 2 -2 2 2 4 1 .2 2 4 2 .4 4 .8 4 1 1 1 1 1 1 1 10 8 8 10 8 8 1 1 2 2


9-94


9-95

FLOOR P L A T E S AND FLOORMATS REF. 1 2 3 6 7 8 9 10 12 15 16

PART NO. 234913A1 298449A1 127377A1 833-40406 353-422 127378A3 243122A1 182296A1 280-16516 233724A1 223199A1

Bur 7-3350

DESCRIPTION PLATE - floor, front cover PLATE - floor, rear cover PLATE - floor, loader control lever mounting NUT - U-type, 6 mm -1.0 PLUG - button, 1-1/4 inch, nylon, used on models without clam bucket GROMMET - rubber, floor FLOORMAT - cab models, waffle back PAD - foam, floormat, if used. SCREW - self-tapping, hex washer head, No. 1 0 - 1 6 x 1 inch BOLT - hex washer, self-aligning, 6 - 1.0 x 25 mm BRACKET - mounting, heater hoses, if used

REQ'D.

4 19 1


9-96

B9501146S


9-97

REAR F E N D E R S AND R E A R C L O S U R E PANEL ROPS CANOPY MODELS REF. PART NO. 1 133025A1 2 133024A1 141404A1 3 4 781-24830 5 144282A1 6 413-516 7 . 492-11031 8 495-21038 136745A1 9 10 112865A1 11 425-285 12 614-8025 13 . 832-10408 14 614-8030 15 . 892-11008 16 495-81001 17 144282A1 18 833-40408 19 614-8045 20 21 22 23 24 25 26 27 28

.814-8035 895r11008 832^10408 188482A1 182594A1 184726A1 842-1425 895-11004 832-10404

Bur 7-3350

DESCRIPTION REQ'D. FENDER-left-hand. 1 FENDER - right-hand • • • -1 PLATE - fender support 2 BOLT - hex flange, self-tapping, 8 - 1.25 x 30 mm 4 SPACER -16 X 10 mm long, fender support plate 4 BOLT - hex, 5/16 NC x 1 inch . . 2 WASHER-lock, 5/16 inch 2 WASHER - flat, 3/8x 7/8 x 3/32 inch. 8 PANEL - rear closure. 1 SCREW - pointed, self-aligning, special, 5/16 NC x 13/16 inch 3 NUT - hex flange, 5/16 inch NC. : 3 BOLT - hex, full threads, 8 - 1,25 x 25 mm 2 NUT - hex, self-locking, 8 mm - 1.25 4 BOLT - hex, full threads, 8 - 1.25 x 30 mm 12 WASHER - lock, 8 mm 19 WASHER - flat, 3/8 x 1-1/8 x 1/16 inch-. 14 SPACER - 16 X 10 mm long .10 NUT-U-type, 8 m m - 1 . 2 5 .12 BOLT - hex, full threads, 8 - 1.25 x 45 rnm, mud guard to fender, see page 9-101 for mud guard . 2 BOLT - hex, 8 -1.25 x 35 mm, mud guard to fender, see page 9-101 for mud guard 2 WASHER - flat, 9 x 17 x 1.6 mm 6 NUT - hex, self-locking, 8 mm - 1.25 4 SEAL - foam, fender 2 BRACKET - velcro retainer 2 STRAP - velcro, right-hand fender 1 SCREW - machine, oval countersunk Phillips, 4 - 0.7 x 25 mm .4 WASHER - flat, 4.4:X 9 x 0.8 mm 4 NUT - hex, self-locking, 4 mm - 0 . 7 . . . 4

issued February, 1998

9-98

B9501147S


9-99

REAR FENDERS CAB MODELS REF. 1

PART NO. 132134A1

1A

181457A2

1B

131975A2

2 3 4 5 , 6 7 8 8A SB

182594A1 184726A1 842-1425 895-11004 832-10404 188482A1 132133A1 304390A1 303022A1

8C

188411A2

8D

192274A2

9 10 11 12 13 14 15 16 17 18 19

139362A1 495-81002 832-10410 . 614-8030 495-81001 832-10408 144282A1 892-11008 833-40408 495-21038 140-107

20

231-14109

Bur. 7-3350

DESCRIPTION REQ'D. FENDER - right-hand, gray, for hardware mounting the front of the fender, see mud guard page 9-101 1 PANEL - fender, right-hand upper, gray yinyl, optional deluxe interior, not shown ; 1 PANEL - fender, right-hand lower, gray vinyl, optional deluxe interior, not shown 1 BRACKET - velcro retainer 2 STRAP - velcro, right-hand cab fender 1 SCREW - machine, oval countersunk Phillips, 4 - 0.7 x 25 mm 4 WASHER - flat, 4.4 x 9 x 0.8 mm 4 NUT - hex, self-locking, 4 mm - 0.7 4 SEAL - foam, ROPS post to fender 2 FENDER - left-hand, gray 1 PANEL - fender, left-hand, gray vinyl, optional deluxe interior, not shown 1 INSERT - coffee cup holder, black plastic liner, optional deluxe interior, not shown, see items 19 and 20 for screw and nut .1 INSERT - tool tray, black plastic liner, optional deluxe interior, not shown, see items 19 and 20 for screw and n u t . . . . . . 1 COVER - left-hand fender at cab entrance, black plastic, optional deluxe interior,, not shown, see items 19 and 20 for screw and nut 1 STUD - upper ball, 10 mm -1.5, left-hand fender 1 WASHER - flat, 7/16x1 -3/8 x 5/64 inch .2 NUT - hex, self-locking, 10 mm -1.5 1 BOLT - hex, full threads, 8 - 1.25 x 30 mm .22 WASHER - flat, 3/8 x 1-1/8 x 1/16 inch 16 NUT - hex, self-locking, 8 mm - 1 ;25 4 SPACER -16 X 10 mm long, fender support plate , 22 WASHER - lock, 8 mm 18 NUT - U-type, 8 mm -1.25 20 WASHER - flat, 3/8 x 7/8 x 3/32 inch 10 SCREW - machine, pan head Phillips, No.-10 NC x 3/4 inch, retains tool tray and coffee cup inserts and fender cover at cab entrance, not shown 7 NUT - hex, self-locking. No. 10 NC, used with item 19, not shown 7


9-100

^^^^^

3h i---

h--—-n^-^

V


9-101

MUD GUARD REF. 1 2 3 4 5 6 7 8 9 10 11 12

PART NO. 137655A3 182396A2 136279A2 614-10030 892-11010 895-11010 136280A1 814-8035 895-11008 832-10408 614-8045 833-40408

Bur 7-3350

DESCRIPTION PLATE - reinforcement GUARD - mud, mounts at right-hand fender ANGLE - mud guard BOLT - hex, full threads, 10 -1.5 x 30 mm WASHER - lock, 10 mm WASHER - flat, 11 x 20 x 2 mm ANGLE - mud guard BOLT - hex, 8 - 1.25 x 35 mm WASHER - flat, 9 x 17 x 1.6 mm . . . . . NUT - hex, self-locking, 8 mm -1.25 BOLT - hex, full threads, 8 - 1.25 x 45 rpm . . . . NUT - U-type, 8 mm - 1.25, fender to frame

REQ'D. 1 1 1 .2 2 2 1 • • • -2 -6 4 2 2


9-102

BS97N022

580 Super L Series 2 Loader Baclchoe

9-103

S E A T S AND MOUNTING PARTS REF. 1

PART NO. 185156A1 293021A1

2

258313A1 293022A1

2A

259071A1 292262A1 292263A1

3 4 5. 7 8 9 10 11 11A 11B

614-12040 L77821 892-11012 118769A1 470-10620 495-31016 193-1003 119211A1 186351A1 896-11012

DESCRIPTION REQ'D. SEAT ASSEMBLY - standard, gray vinyl, without armrests, includes seat, pedestal, and support, see parts list page 9-109 for seat and page 9-111 for support and pedestal 1 SEAT ASSEMBLY - suspension, gray cloth, complete, includes armrests and mounting hardware (Ref 3-11 and 11 B), without seat belts and hardware, component parts list not available at time of printing 1 SEAT ASSEMBLY - suspension, gray cloth, includes seat, suspension and pedestal, without armrests, component parts list not available at time of printing.; 1 SEAT ASSEMBLY - suspension, gray vinyl, complete, includes armrests and mounting hardware (Ref 3-11 and 11B), without seat belts, component parts list not available at time of printing 1 SEAT ASSEMBLY - suspension, gray vinyl, includes seat, suspension and pedestal, without armrests, component parts list not available at time of printing 1 KIT - left-hand armrest, included in 293021A1 or 293022A1 complete seat assembly,icomponent parts list not available at time of printing 1 KIT - right-hand armrest; included in 293021A1 or 293022A1 complete seat assembly, component parts list not available at time of printing 1 BOLT - hex, full,threads,,12 - 1.75 X 40*mm, standard or suspension seat 4 GROMMET -wire, standard or suspension seat 1 WASHER-lock, 12 mm 4 SWITCH - limit, with harness, attaches to side console harness 1 SCREW-machine, pan head slotted. No. 6 NCx 1-1/4 inch 2 WASHER-flat, 5/32x3/8 X 3/64 inch. . . . . 2 NUT - hex, with external tooth lock washer, No. 6 NC 2 BRACKET-switch mounting,-suspension seat only. 1 BRACKET- harness guard, seat swivel 1 VVASHER - flat, 13.5 x 24x 3 mm, hardened, at switch bracket mounting 1

SEAT BELT MOUNTING - STANDARD SEAT 12 13 14 15 17 18 19

D150377 R58418 414-728 D150391 495-81169 496-81010 232-4617

BELT - seat, 51 mm (2 inch) wide, if used. BELT - seat, retractable, 76 mm^ (3 inch) wide, if used BOLT-hex, 7/16 NFx 1-3/4 inch SPACER - belt , WASHER - flat, 17/32 x 2-1/2 x 3/64 inch, not used on deluxe air seat WASHER - flat, 15/32 x 1 x 7/64 inch, hardened NUT - hex, self-locking, 7/16 inch NF

1 1 2 2 2 5 2

SEAT BELT MOUNTING- SUSPENSION SEAT 20 21 22 23 25 26

*D150377 * R58418 *414-724 D150391 * 496-81010 * 232-4617

BELT - seat, 51 mm (2 inch) wide, if used BELT - seat, retractable, 76 mm (3 inch) wide, if used BOLT - hex, 7/16 NF x 1-1/2 inch SPACER - belt. . WASHER - flat, 15/32 x 1 x 7/64 inch, hardened NUT - hex, self-locking, 7/16 inch NF

1 1 2 2 3 2

* NOTE: Above parts are also used with the deluxe air suspension seat.

Bur 7-3350


9-104

9-105

D E L U X E AIR SUSPENSION S E A T REF.

1

PART NO. 121414A1 614-12030 892-11012 275547A1 300657A1 300659A1 300661A1 300662A1 300663A1 300664A1 1999693C1 300665A1 300667A1 1987212C1 300669A1 300670A1 1987219C2 1987290C1 135512A3 259054A1 1344025C1 1344026C1 300672A1 D137363 300674A1 300675A1 300677A1 300679A1 300680A1 300681A1 300683A1 300684A1 300685A1 226560A1 300688A1 132862A1 143786A1 197793A1 132866A1 300689A1 300690A1 180593A1 231-1444 340-12520 300691A1

DESCRIPTION FUSE - mini, 20 ampere, not shown BOLT - hex, full threads, 12 - 1.75 x 30 mm WASHER - lock, 12 mm SEAT ASSEMBLY - air suspension, cloth, deluxe, complete with armrests, exploded illustration of seat not available at time of printing KIT - seat top assembly KIT - armrest, right-hand KIT - armrest, left-hand KIT - seat cushion, with frame KIT - backrest cushion, with frame KIT - backrest cover CLIP - Christmas tree, package of 14 KIT - lumbar, with knob KNOB - lumbar. KIT - seat cushion, back tilt knob PEDESTAL - weldment KIT - lateral isolator KIT - lateral isolator shock KIT - spring, isolator KIT - roller bearing, isolator KIT - lateral isolator control PIN - clevis, pivot SPRING - latch SWITCH - height adjustment • SWITCH - contact HARNESS - swivel switch KIT - slide/swivel assembly KIT - upper slide plate assembly SLIDE - latch weldment KIT - slide puck LEVER - slide control LEVER-swivel BELT - tether KIT - air suspension assembly HOUSING - lower, with upper stop bracket HOUSING - upper ARM - suspension SHAFT - bearing KIT - air spring KIT - shock absorber KIT - compressor and valve MOUNT - compressor KIT-bumper NUT - hex, self-locking, 1/4 inch NC SCREW - machine, pan Phillips, 1/4 NC x 1-1/4 inch KIT - fore/aft isolator latch

REO'D. 1 4 4

2 2 1

NOTE: See page 9-103 for seat belts and mounting. Continued on next page

Bur 7-3350


9-106

mm

BS97N036


9-107

DELUXE AIR SUSPENSION S E A T REF. 1

PART NO. 275547A1 1981850C1 300692A1 133422A1 A45054 133421 A t 132872A1 180594A3 131-425 300896A1 1990548C4 LI 8337 176091A1

Bur 7-3350

DESCRIPTION SEAT ASSEMBLY - air suspension; cloth, deluxe, complete with armrests, exploded illustration of seat not available at time of printing, continued from previous page KNOB - isolator control KIT - fore/aft isolator latch ' BUMPER - rubber i BUMPER-seat KIT - boot, with pins KIT - boot pin, package of 23 retainers and 3 dome nuts KIT - rollers and bearings NUT - push-on type, 1/2 inch HARNESS - wire KIT - air line and fittings STRAP - tie, 15 inch KIT - retaining, hog ring, package of 50 rings for cushions

REO'D.

4 1


9-108

f-<5©

BS97D076


9-109

STANDARD S E A T A S S E M B L Y REF.

PART NO. 185156A1

1 2 3 4

176926A1 176925A1 116760A1 119171A1

5 6

176924A1 ^181169A1

7 8 9

NSS NSS 234223A1

DESCRIPTION SEAT ASSEMBLY - standard, gray vinyl, not serviced as a complete assembly, for service order respective component kits, see page 9-111 for standard support and pedestal KIT - backrest cushion, gray KIT - seat cushion, gray . . .. KIT - adjuster, seat slide, fore/aft KIT - spring, seat adjuster slide, also includes vertical latch and extension springs used in the standard pedestal on page 9 - 1 1 1 . . . . TRIM - edging, gray, cushion to shell. KIT - cable, fore-aft/swivel mechanism, also includes cable on page 9-111 CLIP - retainer, order N7802 clip kit, see below SHELL - seat frame, order 234223A1 shell, cushion and trim kit, Ref 9 . KIT - seat shell, cushion and trim, includes Ref 1, 2, 5 and 8 . .

N7802

KIT - clip, includes item 7 clip above, plus 6 additional narrow clips

REO'D.

1

NOTE: Each kit includes an instruction sheet.

Bur 7-3350


9-110

9

A WARNING

^3) LUBRICATE SWIVEL POST (GREASE FITTING ON SIDE)


9-111

STANDARD S E A T SUPPORT AND P E D E S T A L REF.

PART NO. 185156A1

1 2 3 4 5

* 116761A2 116763A1 * 116764A2 * 116766A2 * 116767A1

6 7

119171A1 181169A1 253209A1

DESCRIPTION SEAT ASSEMBLY - standard, gray vinyl, includes seat on page 9-109 and support and pedestal below, individual connponent parts not serviced separately, for service order respective kits KIT - support, base. . KIT - cable, anchor, includes hardware for both ends of cable KIT - pedestal, includes 219-16 grease fitting KIT - pedestal box, includes 219-16 grease fitting KIT - swivel latch, includes (6) lock nuts, (1) push nut and (1) swivel latch, if used KIT - spring, also includes seat slide adjuster spring on page 9-109 KIT - cable, fore-aft/swivel mechanisnn, also includes (4) nuts on page 9-109 KIT - swivel latch, includes (4) lock nuts, (1) rivet, (1) spacer, (1) washer, (1) push nut and (1) swivel latch, if used

REQ'D. 1 . . . . .1 1 1 1 1 1 1 1

NOTE: Each kit includes an instruction sheet. * NOTE: , Also includes (4) lock nuts for seat adjuster slide on page 9-109.

Bur 7-3350


9-112

BS97M223


9-113

R O P S C A B AND G L A S S REF. 1

PART NO. 280995A1

1

280996A1

2 3 4 5 6 7 8 9 10 11

97290C1 D126204 D126205 107230A1 107233A1 107232A1 107234A1 108513A1 143369A2 286-56520

DESCRIPTION REQ'D. OAB ASSEMBLY - ROPS, operators, complete with heat, order from Machinery Price List, parts list pages 9-113 thru 9-145 CAB ASSEMBLY - ROPS, operators, complete with heat and air conditioning, order from Machinery Price List, parts list pages 9-113 thru 9-145 GLASS - front windshield GLASS - right-hand rear quarter panel window GLASS - left-hand rear quarter panel window GLASS - knee, upper, right-hand GLASS - knee, upper, left-hand GLASS - knee, lower, right-hand GLASS - knee, lower, left-hand SEAL - 290 mm (11-7/16 inch) long, front knee glass 2 MIRROR - rear view, interior 1 SCREW - self-tapping. Fillister head. No. 10 NC x 1-1/4 inch 2

NOTE: The grab handles are welded to the cab frame and there is no service replacement for these handles.

Bur 7-3350

Issued Febi-uary, 1998

9-114

(32) (31)

BT97N184

(15


9-115

C A B FRAME, C O V E R S AND INSULATION REF. 1 2

PART NO. 281009A1 137851A1

3

844-8020

4 4A 5 6 7 8 9 10 11

126371A1 131977A2 291609Ail 108963A1 108797A1 127021A2 205-129 353-415 353-410

12 14 15 16 17 18 19 20 21 22 23 24 25

833-40406 294666A1 296367A1 282845A1 E47027 227420A1 840-1516 614-6025 892-11006 833-40406 227178A2 829-1408 • 292264A1

26 27

299001A1 300152A1 833-40406 614-6020 895-15006 297915A1 297913A1 297914A1 303105A1 303108A1 303109A1 303106A1

DESCRIPTION REQ'D. FRAME - ROPS cab, this frame is not serviced separately 1 PLATE - bar, front console mounting to firewall, also shown on page 4-23, no longer included with frame, purchase separately 2 BOLT - heavy hex flange, 8 - 1.25 x 20 mm, no longer included with frame,.purchase separately 13 COVER - plastic, right-hand post 1 COVER - gray vinyl, right-hand post, optional deluxe interior 1 COVER - gray vinyl, left-hand post, optional deluxe interior 1 SEAL - trim, right-hand post 2 PAD - insulation, rear, 200 x 813 x 6.4 mm, cut from 108794A2 bulk pad . . . . . .1 PAD - insulation, front cab roof 1 PLUG - button, 2 inch ID, floor .2 PLUG - button, 1-1/2 inch, cab roof, models without radio antenna . . . . . . . . . . . 1 PLUG - button, 7/8 inch, windshield frame, top, models without radio antenna -1 NUT - U-type, 6 mm - 1.0 4 COVER - coat hook 1 STRAP-velcro 1 STRAP - velcro .1 VISOR - sun shade 1 BRACKET - visor mounting 1 SCREW - niachine, pan Phillips, 5 - 0.8 x 16 mm 3 BOLT - hex, full threads, 6 -1.0 x 25 mm 2 WASHER - lock, 6 mm 2 NUT - U-type, 6 mm -1.0 2 BRACKET - visor support 1 NUT - hex, 8 mm -1.25, class 10 1 TRAY - tool, storage, mounts behind right-hand console, optional deluxe interior 1 COVER - right-hand lower front, optional deluxe interior 1 COVER - left-hand lower front, optional deluxe interior, not shown 1 NUT- U-type, 6 mm-1.0 . . 2 BOLT - hex, full threads, 6 -1.0 x 20 mm 2 WASHER - flat, 6.6 x 25 x 1.6 mm 2 SEAL - noise reduction, insulation, right-hand front firewall 1 SEAL - noise reduction, insulation, front firewall 1 SEAL - noise reduction, insulation, left-hand front firewall 1 SEAL - noise reduction, insulation, front firewall 2 SEAL - noise reduction, insulation, left-hand firewall .1 SEAL - noise reduction, insulation, firewall 1 SEAL - noise reduction, insulation, right-hand firewall .1

108794A2

PAD - bulk, 577 x 813 x 6.4 mm, insulation

28 29 30 31 32 33 34

Bur 7-3350

1


9-116

3

&

BT97M185

(p)


9-117

LEFT-HAND AND RIGHT-HAND C A B DOORS - EXTERIOR REF. 1 1A 2 3

PART NO. 137869A3 137868A3 R53562 187582A2

4

R53444

5 5A 6 6A 7 7A 8 9

R52882 R52881 R52880 R52879 R52884 R52883 R52917 142-103

10

F64198

11

F45165

12 12A 13 14

196675A2 196673A2 F64342 231-14109 255450A1

15 15A 15B 16 17 17A 18 19

255453A1 814-8045 832-10408 D135387 R55000 R55001 A180163 265-16512

20

137731A1

21 21A 22 23

1977401C1 1977402C1 443-13112 231-5145

Bur 7-3350

DESCRIPTION REQ'D. FRAt\/lE - right-hand door 1 FRAME - left-hand door, not shown 1 BRACKET - cable, welded to left-hand or right-hand door frame 1 SEAL - bulb type, with drain holes, 4585 nfim (180-1/2 inch) long, with self adhesive 2 SEAL - bulb type, 2689 mm (105-7/8 inch) long, left-hand and right-hand window frames 2 GLASS - right-hand door, rear window, tinted GLASS - left-hand door, rear, window, tinted, not shown GLASS - right-hand door, front, tinted GLASS - left-hand door, front, tinted, not shown GLASS - right-hand door, lower, tinted GLASS - left-hand door, lower, tinted, not shown HINGE - glass, door window 4 SCREW - machine, oval Phillips, No. 10 NC x 3/4 inch, left-hand and right-hand door window hinge 12 SPACER - nylon, black, glass to hinge, left-hand and right-hand door window hinge 12 NUT - hex, self-locking, special. No. 10 NC, Teflon coated, left-hand and right-hand door window hinge 12 HANDLE - right-hand door, outer 1 HANDLE - left-hand door, outer, not shown 1 GASKET - door handle, left-hand and right-hand 2 NUT - hex, self-locking. No. 10 NC, left-hand and right-hand handles 4 KIT - service, inner door handle, includes (1 each) Ref 15 - 15B, plus instructions 1 LEVER - inner left-hand or right-hand door latch handle 1 BOLT - hex, 8 - 1.25 x 45 mm 1 NUT - hex, self-locking, 8 mm -1.25 1 KNOB - lever, inner door latch 2 LATCH ASSEMBLY - door, right-hand, rotary 1 LATCH ASSEMBLY - door, left-hand, rotary, not shown 1 SPRING - extension, left-hand or right-hand door latch 1 SCREW - self-tapping, oval Phillips, No. 10-16 x 3/4 inch, left-hand and right-hand door latch 4 SCREW - machine, flat head Phillips, special, 1/4 NC x 1 inch, left-hand and right-hand door latch 8 BRACKET - latch, right-hand rotary 1 BRACKET - latch, left-hand rotary, not shown 1 SCREW - machine, flat Phillips, 5/16 NC x 3/4 inch 6 NUT - hex serrated flange, 5/16 inch NC 6


9-118

9 fey %

BS97N097


LEFT-HAND AND RIGHT-HAND C A B DOORS REF. 1 1A 2 3 4 5 6 7 8 9. 10 11 12 13 13A 14

PART NO. 137868A3 137869A3 .R53562 281069A1 281068A1 140-104 F45165 142-103 F64198 195-81023 F44881 1340345C1 230-4215 108938A2 108936A2 260-16524

15 16 17

R53000 1958970C1 165-129

18 19 20 21 22 23 24 25 26 27

1971368C1 1977399C1 413-48 492-11025 R54047 F44883 291129Ai 280336A1 895-11008 100-3331

Bur 7-3350

9-119

INTERIOR

DESCRIPTION FRAME - left-hand door. FRAME - right-hand door, not shown BRACKET - cable, welded to left-hand or right-hand door frame HANDLE - door window q . .> LATCH - push type, door window|. SCREW - machine, pan .head Phillips, No., 8 NC x 3/4 inch NUT - hex, self-locking, special, rilo. 10 NC SCREW - machine, oval Phillips, |No. 10 NC x 3/4 inch SPACER - nylon, black, glass to bracket WASHER - flat, 1/4 x 9/16 x 3/64 inch. CYLINDER - door, left-hand and right-hand STUD - ball, cylinder NUT - hex, self-locking, 5/16 inch' NC PANEL - left-hand door J. , PANEL - right-hand door J ... SCREW - self-tapping, pan Phillies, No-. 10-16 x 1-1/2 inch, black, left-hand arid right-hand door pariels RETAINER - screw, left-hand and right-hand door panels HANDLE-,- left-hand and right-hand inner door BOLT - hex socket, self-locking, 1/4 NC x 3/4 inch, black, left-hand and right-hand inner door handles PLATE - retainer, left-hand and'right-hand inner door handle .. . : BRACKET - cylinder . i . .. . .'. BOLT - hex, 1/4 NC x 1/2 inch. i. . . WASHER - lock, 1/4 inch." . . . . . . . . . ' . /. SHIM - latch bracket, left-hand and right-hand door window. RETAINER - lock, clip.. .| ROD - window prop, hold open, left-hand ROD - window prop, hold open, right-hand, not shown... WASHER - flat, 9 x 17 x 1.6 mm RING - E-type, external retaining. No. 31

REQ'D. 1 1 1 2 2 A 8 4 4 8 2 2 2 .1 • •1 4 .4 . .2 8 4 2 4 4 4 .2 1 .. : . . .1 4 2


9-120

@

BS97N098


9-121

LEFT-HAND AND RIGHT-HAND C A B DOOR MOUNTING REF. 1 2 3 4 6A 8 9 10 11 12

PART NO. REF 413-6152 F64046 131-203 495-21038 L60224 F44881 1340345C1 230-4215 230590A1

12A

230589A1

13 14 15 16 17

230588A1 413-420 D36669 230-4214 281-18712

18 19 20 21 22 23 24 25 26 27

R52735 F44748 495-81148 230-4217 107949A1 139362A1 495-71041 832-10410 136-154 225059A1 228689A1

Bur 7-3350

DESCRIPTION REQ'D. DOOR - cab, see page 9-117 through 9-121 1 BOLT - hex, 3/8 NC x 9-1/2 inch 4 WASHER - thrust, plastic 8 NUT - light hex, self locking, 3/8 inch NC 4 WASHER - flat, 3/8 x 7/8 x 3/32 inch 4 BUMPER - rubber, cab door frame and window latch 4 CYLINDER - door, left-hand and right-hand 2 STUD - ball, cylinder, right-hand door 1 NUT - hex, self-locking, 5/16 inch NC 2 BRACKET - left-hand cab door window retaining, mounts to frame, black, not shown 1 BRACKET - right-hand cab door window retaining, mounts to frame, black .1 LATCH - door window to cab frame 2 BOLT - hex, 1/4 NC x 1-1/4 inch, latch to bracket 2 SPRING - compression, left-hand and right-hand window latch release 2 NUT - hex, self-locking, 1/4 inch NC 2 SCREW - self-tapping, hex washer head, 1/4 NC x 3/4 inch, bracket to frame 6 STRIKER - door latch 2 SPRING - Belleville, washer 2 WASHER - flat, 7/16 x 1-1/4 x 1/8 inch 2 NUT - hex, self-locking, 7/16 inch NC 2 BUSHING - door hinge 8 STUD - upper ball, 10 mm -1.5, cylinder, left-hand door 1 WASHER - flat, 13/32 x 1-1/4 x 3/32 inch 2 NUT - hex, self-locking, 10 mm -1.5 1 PIN - cotter, hair, 7/64 x 1-1/8 inch, mounts to clevis pin welded to frame 4 CABLE - door, upper 2 PIN - clevis, welded to cab frame, not shown 4


9-122

B9408275S

580 Super L Series 2 Loader Backhoe C A B REAR WINDOW REF. 1 2 3 4 5 6 7 8 9 11

PART NO. 97256C3 97257C3 97258C3 97259C3 281-54512 458-412 D129974 231-5344 1989960C1 179355A1

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

D129967 97278C1 442-11016 F64198 230-42409 1990727C1 1344232C1 1990728C1 100-3337 D129968 D126198 97277C1 D129969 D126198 137315A1 106974A1

Bur 7-3350

9-123

DESCRIPTION BRACKET - right-hand, upper BRACKET - right-hand, lower BRACKET - left-hand, upper BRACKET - left-hand, lower SCREW - self-tapping, hex washer head. No. 10 NC x 3/4 inch BOLT - hex flange, 1/4 NC x 3/4 inch BRACKET - window, lower rear NUT - hex flange, self-locking, 1/4 inch NC CHANNEL - track SEAL - foam, adhesive-backed, 1536 mm (60-15/32 inch) long, special, track channel both sides GLASS - upper rear window LATCH - upper rear window only SCREW - machine, oval Phillips, No. 10 NC x 1 inch SPACER - nylon, black, special NUT - hex, self-locking. No. 10 NC SPRING - right-hand latch LEVER - latch, metal, left-hand and right-hand ^ SPRING - left-hand latch RING - E-type, external retaining. No. 37, latch lever GLASS - center rear window SEAL - 912 mm (35-29/32 inch) long, center window glass LATCH - window, center window GLASS - lower rear window SEAL - 912 mm (35-29/32 inch) long, lower window glass TRIM - edge, bulk, 900 mm (35-7/16 inch) long, lower rear glass SEAL - foam, adhesive-backed, 20 x 10 x 912 mm, upper rear glass

REQ'D. 1 1 1 1 18 2 2 2 2 4 1 2 8 8 8 2 4 2 8 1 1 2 1 1 1 1


9-124

6

B9504147S

580 Super L Series 2 Loader Backhoe C A B CONTROL PANEL AND WIRING

9-125

REF. 1 , 2

PART NO. 135185A1 135183A1

3 4 5 6

136036A1 286-56520 281-54512 111282C1

7 8 9 10 11 12 13 14 15 16

126844A1 245258A1 R52440 245706C1 R52415 A42561 1340287C1 R52483 REF 895-11008 458-412

17

D36179

18 19

473321 CI 1964672C1

DESCRIPTION REQ'D. PANEL - cab control, includes decal, mounts on right-hand ROPS post . . . . . . . 1 DECAL - instrument symbols, wipers and environmental control, item 3 shown on page 9-155 1 BRACKET - switch support 1 SCREW - self-tapping. Fillister head, No. 10 NC x 1-1/4 inch 4 SCREW - self-tapping, hex washer head, No. 10 NC x 3/4 inch 2 KNOB - control, switch, front and rear wiper, heater, blower, and air conditioner 4-5 PLUG - cab accessory, see page 9-127 for windshield washer switch 1 SWITCH - blower 1 SWITCH - rear wiper 1 PLUG - plastic, rear wiper, blower, windshield wiper, if used, not shown 3 SWITCH - front wiper 1 NUT - retaining, 7/16 inch NC, switch 4 SWITCH - temperature control, air conditioning 1 VALVE - temperature control, heater 1 HARNESS - cab, main, see page 4-31 for cab harness 1 WASHER - flat, 9 x 17 x 1.6 mm 2 BOLT - hex flange, 1/4 NC x 3/4 inch, mounts heater temperature control valve to ROPS post 2 TRIM - edge, 108 mm (4-1/2 inch) long, cut from F42827 bulk trim, control panel bracket, see below 1 STRAP-tie 4 LIGHT - indicator, amber, 14 volt, air conditioning 1

F42827


Bur 7-3350

1


9-126

BT97N197 '


9-127

WINDSHIELD W A S H E R S - FRONT AND REAR REF. 1 2 3 4 5 6 7 8 9 10 11 12 13

PART NO. E46560 NSS E47238 E47239 E47240 226376A1 806-8040 895-15008 515-2295 814-10040 895-11010 E46561 D147383 292408A1

14 15 16

295597A1 832-10410 284154A1

17 18 19

492-11038 425-106 226584A1

20 21 23 24

226582A1 226580A1 E46524 305818A1

28

E43769

29

144900A1

30

305578A1

Bur 7-3350

DESCRIPTION REQ'D. RESERVOIR - windshield washer 1 RESERVOIR - windshield washer 1 PUMP - windshield washer 2 GASKET - mounting 2 CAP - reservoir 1 BRACKET - reservoir mounting, mountings to firewall 1 BOLT - hex, self-locking, 10 -1.5 x 40 mm, class 10.9 2 WASHER - flat, 9 x 20 x 1.6 mm 2 CLAMP - P-type, 3/8 inch ID 1 BOLT-hex, 1 0 - 1 . 5 x 4 0 mm 2 WASHER - flat, 11 x 20 x 2 mm 2 SPACER - plastic 2 CLAMP - J-type, 5/8 inch diameter 1 HOSE - 850 mm (33-1/2 inch) long, front washer, fixed hoodito reservoir pump closest to the firewall 1 BRACKET - support, uses existing air cleaner mounting hardware 1 NUT - hex, self-locking, 10 mm - 1.5 2 NOZZLE - washer, front, includes steel and rubber washer which are not serviced separately -I WASHER - lock, 3/8 inch 1 NUT - hex, 3/8 inch NC 1 HOSE - 5020 mm (197-11/16 inch) long, rear washer, mounts to reservoir pump located the furthest away from the firewall 1 SLEEVE - hose, 1850 mm (72-7/8 inch), lower hose 1 SLEEVE - hose, 520 mm (20-1/2 inch), upper hose 1 GROMMET - rubber, 8 (5/16) ID x 23 mm (29/32 inch) OD 2 BRACKET - rear nozzle mounting, uses existing lamp mounting hardware 1 NOZZLE - washer, rear, includes rubber gasket which is not serviced separately 1 SWITCH - rocker, windshield washer, front and rear, mounts in cab control panel 1 CLAMP - hose 1


9-128

B9402088S

9-129


C A B FRONT WINDSHIELD WIPER REF.

PART NO A186171

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

A186256 N8359 N8362 N8361 L112090 N8360 N8358 N14112 N8356 L112088 L112087 L112089 L112090 L112081 R54504 D128745 *A187909

17A

*132024A1

18 19

414-412 492-11025 *1983335C1 * 132025A1

DESCRIPTION WIPER ASSEMBLY - windshield, 12 volt, with bracket, front windshield wiper MOTOR - wiper, 12 volt, windshield wiper BRACKET - windshield wiper assembly SCREW - with washer, special, motor to bracket WASHER - Belleville NUT - hex, special ARM-drive LINK-wiper SHAFT - pivot SCREW - special, pivot shaft to bracket WASHER - special, large, shaft NUT - special, large, shaft WASHER - wave, special, shaft end NUT - hex, special, shaft end CAP - pivot shaft end SPACER - pivot shaft ARM - windshield wiper, 570 mm (22-7/16 inch) long, complete BLADE - wiper arm, complete, used in production, 500 mm (19-11/16 inch) long, not available for service, for complete blade order item 17A, 132024A1 BLADE - wiper arm, complete, for blade only, order 132025A1 blade refill, shown below BOLT - hex, 1/4 NF x 3/4 inch WASHER-lock, 1/4 inch

REQ'D. 1 1 1 .3 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 2 2

BLADE - rubber, 500 mm long, refill for A187909 complete blade, see note, no longer available, order item 17A, 132024A1

1

BLADE - rubber, 500 mm long, refill for 132024A1 complete blade, see note

1

NOTE: See the blade ends in the illustrations for items 17 and 17A to determine which blade to order.

Bur 7-3350


9-130

B9501153S


9-131

C A B REAR WINDSHIELD WIPER REF. 1 2 3 4 5 6 7 8 9 .. 10 11 12 13 14 15 16 17 18 19 20 21 22 23

PART NO. A187714 A165395 425-157 184118A1 N8362 D128018 NSS N8362 N8361 L112090 D128020 D128021 L112088 L112087 413-416 492-11025 425-104 L112089 L112090 L112081 R52408 D128022 495-21044 193707A1

Bur 7-3350

DESCRIPTION REQ'D. SWITCH - wiper stop, mounts to window frame inside filter compartment WASHER - fiat, 1/2 x 1 x 1/16 inch, used as a seal NUT - hex, jam, 7/16 inch NF : MOTOR-wiper, 12 volt, rear windshield wiper SCREW - with washer, special, motor to cab frame LINK ASSEMBLY - wiper, rear motor to wiper pivot shafts . LINK - crank SCREW - with washer, special WASHER - Belleville NUT - hex, special SHAFT - pivot, with ball, includes nut SHAFT - pivot WASHER - special, large, shaft NUT - special, large, shaft BOLT-hex, 1/4NCx1 inch WASHER-lock, 1/4 inch NUT-hex, 1/4 inch NC WASHER - wave, special, shaft end . 2 NUT - hex, special, shaft end 2 CAP - pivot shaft end 2 ARM - wiper, rear windshield 1 BLADE - wiper, rear windshield 1 WASHER - flat, 7/16x1 x 5/64 inch 1 PLATE - retainer, harness, mounts on existing wiper motor mounting bolt 1


9-132

BT97M005


9-133

C A B HEADLINER, L O U V E R S AND DOME LAMP REF.

1 1A 2 3 4 4A 5 6 7 7A 8

PART NO. 137135A1 *300157A1 NSS NSS 131973A1 125688A1 1331102C2 NSS 140-103 125749A1 131-861 186797A1 *F64519

9 10 11 12 13

R53755 NSS N14466 N14465 440-1088 *281-54512

14 15

*194858A1 *D134923 *292654A1

Bur 7-3350

DESCRIPTION REQ'D. HEADLINER ASSEMBLY - cab, standard, models without speakers and radio 1 HEADLINER ASSEMBLY - cab, models with speakers and radio 1 HEADLINER - cab, without speakers and radio 1 HEADLINER - cab, models with speakers and radio 1 SEAL - duct 5 LOUVER - headliner, heat and air 9 LOUVER - air recirculation .1 KNOB - louver, not shown 1 SCREW - machine, pan head Phillips, No. 6 NC x 3/4 inch 24 NUT-U-type, No. 6 NC 24 CLAMP - U-type, No. 10 NC, no threads, dome lamp retaining 2 SEAL - adhesive-backed, 19 x 75 x 550 mm, 137135A1 iheadliner only 1 SCREW - self-tapping, special, No. 10-16 x 3/4 inch, with washer, headliner to cab frame, used in production, order F64315 washer and 265-16512 screw for service 5 LAMP ASSEMBLY - dome, 12 volt, see page 4-17 for switch 1 BASE - dome lamp 1 BULB - dome lamp 1 LENS - dome lamp 1 SCREW - machine, pan Phillips, No. 8 NC x 1/2 inch, base to lens 2 SCREW - self-tapping, hex washer head. No. 10 NC x 3/4 inch, lamp to headliner 2 WASHER - flat, special 2 CAP - bolt, rear headliner 2 KIT - radio-ready package, includes above items marked with an asterisk, plus see parts on pages 4-25 and 4-45

1


9-134

BT97M153

9-135

C A B AIR FILTER REF. 1 2 3 4 5 7 8

PART NO. 139768A1 123206A2 461-33148 495-81121 140327A1 281-54712 243603A1

Bur 7-3350

DESCRIPTION FILTER - air, complete, includes gasket BRACKET - right-hand, air filter retainer BOLT - hex socket, 5/16 NC x 3 inch WASHER-flat, 11/32 x 1-1/2 x 1/16 inch SPACER - filter SCREW - self tapping, hex washer head, 1/4 NC x 3/4 inch SCREEN - filter, rear

REQ'D. 2


9-136

BS97N096


9-137

CAB BLOWER HOUSING, HEAT AND AIR VENTILATION DUCTS AND DRAIN LINES ^ REF. 1

PART NO. 134049202

1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1977564C2 1343938C2 182697A1 189404A1 181981A1 134125A1 128406A1 13lb39A1 131974A1 131041A1 131042A1 131973A1 845^6020 833-40406 1987097C1

16

1987096C1

17 18

.

832-10408 127073A1

19 20 21

214-1404 .109239C2 LI 8337

22 23

184289A1 282-16512

Bur 7-3350

DESCRIPTION REQ'D. BLOWER ASSEMBLY - air, cab, component parts not serviced separately, used in production, for service order 1977564C2 blower assembly and 1343938C1 resistor, items 1A and 2 below 1 BLOWER - cab, air, component parts not serviced separately ; . . .1 RESISTOR - blower 1 RETAINER - plastic fastener 5 HARNESS - jumper, blower 1 SEAL - adhesive-backed, 6 (5/16) x 20 (51/64) x 355 mm (14 inch) l o n g . . . 1 HOUSING - ventilation, heat and air 1 SEAL - ventilation housing to duct 3 DUCT - small, front 1 SEAL - ventilation housing, lower front 2 DUCT - left-hand, large 1 DUCT - right-hand, large 1 SEAL-duct 2 BOLT - heavy hex flange, 6 -1.0 x 20 mm . . 2 NUT-U-type, 6 m m - 1 . 0 2 SEAL - 9 (23/64) x 19 (3/4) x 735 mm (29 inch) long, air conditioning drain pan .1 SEAL - 9 (23/64) x 19 (3/4) x 765 mm (30-1/8.inch) long, air conditioning drain pan 1 NUT - hex, self-locking, 8 mm -1.25 . 4 HOSE - 13 (1/2) x 16 (5/8) x 2850 mm (112-13/64 inch) long, front and rear drain 4 CLAMP-adj, 1/4-5/8 inch dia 4 VALVE-check, drain 4 STRAP - tie, 15 inch, nylon, retaining, retain front drain hoses to hydraulic lines 2 CLAMP - hose, mounts on left-hand fender 1 SCREW - self-drilling tapping, hex washer head. No. 10-16 x 3/4 inch. Teflon 1


9-138


9-139

CAB *HEATER

3 4 5 6 8 9

1954736C1 L50062 R53634 126907A1 825-2408 R52483

10

128410A1

11

128411A1

12 13 14 15 16 17 , 18

L50062 614-8025 895-11008 892-11008 829-1408 190675A1' 225713A1

19 20 21 22 23 23A .24 25. 26

214-1410 301803R1 221-89 LI 7985 221-1382 221-190 D132982 L18337 353-406

27 28 29 30 31

D143427 614-8030 D143417 825-2408 225714A1

32

D88052

DESCRIPTION CORE - heater, mounts in blower housing box, seal mounts on top of heater core on models with heater only, see page 9-141 for seal HOSE -1100 mm (43-5/16 inch) long, cut from 97252CX bulk hose, heater core to temperature control valve CLAMP - adjustable, hose CLAMP - P-type CLAMP - hose, included in air conditioner package SPACER - hose. NUT - hex flange, 8 mm - 1.25 VALVE - temperature control, heater, see page 9-125 for mounting hardware HOSE - 925 mm (36-27/64 inch) long, cut form 97252CX bulk hose, temperature control valve to floor HOSE - 2030 mm (79-15/16 inch) long, cut from 97252CX bulk hose, heater core to floor CLAMP - P-type, hose BOLT - hex, full threads, 8 - 1.25 x 25 mm WASHER - flat, 9 x 17 x 1.6 mm WASHER - lock, 8 mm NUT - hex, 8 mm -1.25, class 10 . . . TUBE - heater elbow at floor... . .. HOSE - 2400 mm (94 inch) long, cut from 97252CX bulk hose, floor to left-hand side of engine, short CLAMP - adj, 9/16 - 1-1/16 inch dia. VALVE - shutoff, shutoff, right-hand side of engine REDUCER - pipe, 1/2 male X 3/8 inch female, replaces existing plug NIPPLE - 3/8 inch PT, left-hand side of engine . ELBOW-street, 90 degree 1/2x3/8 inch PT NIPPLE - straight, 1/2 PT x 2 inch, replaces existing plug SLEEVE - hose guard STRAP - tie, 15 inch, nylon, retaining PLUG - button, 5/8 inch,'air conditioning drain, used on models with heat only CLAMP-tube BOLT- hex, full threads, 8 - 1.25 X 30 mm SPACER - 10 IDx 16 0D x 6 mm long NUT - hex flange, 8 mm -1.25 HOSE - 3300 mm (130 inch) long, cut from 97252CX bulk hose, right-hand side of engine CLAMP - P-type, 1 inch ID, uses existing bellhousing hardware

97252CX

HOSE - bulk, 16 (5/8) x 25 (1) x 15240 mm (600 inch) long

REF. 1

PART NO. 131124A1 128412A1

REQ'D. 1 1 6 2 .2 2 2 • -1 1 1 2 1 1 1 1 2 1 .4 1 1 1 1 1 4 3 2 1 1 1 1 1 .2 1

* NOTE: See page 9-141 for hose clamping at floor plate.

Bur 7-3350


9-140

BS97N099


9-141

CAB *EVAPORATOR CORE AIR CONDITIONING LINES REF. 1 2 3 4 5

PART NO. 13li27A2 1990756C2 128485A1 128484A1 181980A1 83822C1

7 8 9 10 11 12 13 14 15

190599A1 128485A1 128483A1 1250594Ci 1250594C1 122553A1 122579A1 1340287C1 124727A1

16 17 18 19 20 21 22

128483A1 LI 8337 D143427 614-8030 D143417 825-2408 124011A1

23 24 25 26 27

123980A1 181979A1 845-6020 . 833-40406 825-2406 1954475C1

DESCRIPTION CORE ASSEMBLY - evaporator VALVE - expansion O-RING - 9/16 ID x 1/16 inch wide. . O-RING - 7/16 ID X 1/16 inch wide SEAL - adhesive-backed, 19 (3/4) x 19 (3/4) x 680 mm (26-3/4 inch) long, apply seal to top of evaporator core on models with heat and air conditioning TAPE - 610 mm (24 inch) long, cut from 1954475C1 bulk tape, insulation, expansion valve and hoses at expansion valve HOSE - suction O-RING - 9/16 ID X 1/16 inch wide, hose end O-RING-5/16 IDx 1/16 inch wide, hose valve core VALVE - core, hose, low pressure switch VALVE - core, hose, low side service port CAP - sealing SWITCH - low pressure SWITCH - temperature control, air conditioning HOSE - 3200 mm (126 inch) long, pressure, liquid line, attaches to item 24 hose on page 9-143 O-RING - 5/16 ID X 1/16 inch wide, hose end STRAP - tie, 15 inch, nylon, retaining CLAMP - tube BOLT - hex, full threads, 8 - 1.25 x,30 mm SPACER - 10 ID x 16 OD x 6 mm long, hose clamp NUT - hex flange, 8 mm -1.25 GASKET - at cab floor, heat or air conditioned models, trim[center of gasket for air conditioned units CLAMP - heater and air conditioning hoses SEAL-foam BOLT - heavy hex flange, 6 - 1 .O x 20 mm NUT-U-type, 6 mm - 1.0 NUT - hex flange, 6 mm - 1 TAPE - bulk, 63.5 (2-1/2) x 9150 (360) x 3 mm (1/8 inch) thick, insulation

REQ'D. 1 1 1 1 • -1 3 1 1 1 1 1 1 1, 1 1 1 UAR 2 2 2 2 1 2 2 6 4 2 1

* NOTE: Also see page 9-139 for hose clamping.

Bur 7-3350


9-142

TO CAB

BASE


9-143

AIR CONDmONING

CONDENSER AND RECEIVER-DRIER REF. 1 2 3 4 5

PART NO. 305822A1 128485A1 1250594C1 122553A1 D88052

6 7

1999755C2 242724A1

8 9 10 11 12 13 14

128485A1 128484A1 1250594C1 122554A1 193913A1 LI 8337 246060A1

15 16 17 18 19 20 21 22 23 24 25 26

138255A1 128483A1 1250594C1 128483A1 232948A1 1990758C2 253404A1 895-11008 832-10408 305821A1 128483A1 191703A1

27

191704A1

28

614-8030

Bur 7-3350

DESCRIPTION REQ'D. HOSE - 2650 mm (104-11/32 inch) long, compressor to cab base 1 O-RING - 9/16 ID X 1/16 inch wide, hose end 2 VALVE - core, hose, low side service port 1 CAP - sealing 1 CLAMP - P-type, 1 inch ID, hose to inner left-hand side of chassis, uses existing hardware, if used 1-2 COMPRESSOR ASSEMBLY - ajr conditioning, parts list page 9-145 . . 1 HOSE - 2600 mm (102-3/8 inch) long, straight hose end, compressor to condenser 1 O-RING - 9/16 ID X 1/16 inch wide, hose end, at compressor 1 O-RING - 7/16 ID X 1/16 inch wide, hose end 1 VALVE - core, hose, high side charge port . . . .1 CAP-sealing 1 SLEEVE - hose guard, mounts to item 7 hose at hood hinge bolt area 1 STRAP - tie, 15 inch, nylon, retaining UAR CONDENSER - coil, refrigerant cooler, uses existing oil cooler to radiator hardware. ,.. : 1 HOSE - 550 mm (25-11/16 inch) long, condenser to receiver-drier 1 O-RING - 5/16 ID X 1/16 inch wide, hose ends . 2 VALVE - core, for high pressure switch 1 O-RING - 5/16 ID X 1/16 inch wide, hose .1 SWITCH - high pressure, 400 psi . . .1 RECEIVER-DRIER - air conditioning, refrigerant 1 CLAMP - receiver-drier .1 WASHER - flat, 9 x 17 x 1.6 mm . . . .1 NUT - hex, self-locking, 8 mm -1.25 1 HOSE - 3060 mm (120-1/2 inch) long, receiver-drier to cab base 1 O-RING - 5/16 ID X 1/16 inch wide, hose ends 2 SLEEVE - hose guard, 400 mm (15-3/4 inch) long, suction hose, compressor to cab base .2 SLEEVE - hose guard, 460 mm (18-1/8 inch) long, receiver-drier to cab base hose .2 BOLT - hex, full threads, 8 - 1.25 x 30 mm 1


9-144

@

®

BS97N174

/

9-145


AIR CONDITIONING

COMPRESSOR MOUNTING AND DRIVE REF. ' 1 2 3 4 5 6

PARTNO. 1999755G2 NSS 135324A1 A49667 128483A1 LI 8337 A189284

6A

196050A1

7^ 7A 8 9 12 13 14 15 16 18 19 22 23 24 26 27 28 29

•277546A1 S80928 827-10130 896-11010 304530A1 627-10030 896-11010 A184614; 827-10040 304527A1 827-10110 896-11010 832-10410 627-10035 896-11010 D147383 304525A1 304528A1

Bur 7-3350

DESCRIPTION COMPRESSOR ASSEMBLY - air conditioning COMPRESSOR - air conditioning . . CLUTCH ASSEMBLY - compressor PLUG - hex, oil filler 0-RING - 5/16 ID X 1/16 inch wide, plug STRAP - tie, 15 inch, nylon, retaining, compressor wire . . . . PULLEY - air conditioner compressor drive, without powershift transmission PULLEY - air conditioner compressor drive, with powershift^ transmission, not shown BELT - drive, compressor, without powershift transmission BELT - drive, compressor, with powershift transmission, not shown BOLT - hex, 10 - 1.5 x 130 mm, class 10.9. WASHER - flat, 11 x 21 x 2.5 mm, hardened BRACKET - compressor mounting BOLT - hex, full threads, 10 -1.5 x 30 mm, class 10.9 WASHER - flat, 11 x 21 x 2.5 mm, hardened BLOCK - bracket support BOLT - hex, 10 - 1.5 x 40 mm, class 10.9 STRAP - compressor adjusting . . . . . ..| BOLT .hex, 10-1.5 x 110 mm, class 10.9 . WASHER - flat, 11 X 21 X 2.5 mm, hardened NUT-hex, self-locking, 10mm-1.5 BOLT - hex, full threads, 10 - 1.5 x 35 mm, class 10:9 ' WASHER - flat, 11 X 21 X 2.5 mm, hardened CLAMP - J-type, main engine harness to compressor bracket BRACKET - compressor mounting SPACER-short

REQ'D. 1 1 1 .1 1 2 1 1 1 .1 1 5 1 2 2 1 2 2 1 6 4 4 3 . .1 1 1


9-146

BT97N171

9-147


ROPS CANOPY

OPERATOR COMPARTMENT REF. 1

PART NO. 281001A1

2

D60180 ^ 345-133 ,

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 23 24 25 26 27 28 29 30 31

353-405 D93716 353-417 127324A1 282-16512 D147383 128265A1 825-2408 205-129 143121A1 143127A1 781 -24820 892-11008 D143242 180801A1 495-11041 425-106 194513A1 . 286-56520 353-406 127367A1 137851A1 294666A1 296367A1 . 282845A1 E47027 260-14512 307243A1 F42827

DESCRIPTION REQ'D. CANOPY - ROPS, order from Machinery Price List, for service order 281004A1 which is the complete ROPS canopy with decals and mounts 1 TRIM-edge, 368 mm (14-1/2 inch) long, cut from F42827 bulk trim, if used 2 ADHESIVE - Superbonder,409, attaches wire harness to ROPS post, if used 1 PLUG - button, 9/16 inch .4-8 . PLUG - plastic, 3 inch (76 mm) diameter 4 PLUG - button, 2 inch, nylon, driving, flood and work lamps. 8 COVER - wiring, right-hand ROPS post 1 SCREW - self-drilling tapping, hex washer head, No. 10-16 x 3/4 inch. Teflon 3 CLAMP - J-type, canopy harness to ROPS post. . 2 SPACER - clamp 2 NUT - hex flange, 8 mm - 1.25 4 PLUG - button, 2 inch ID, floor 2 SEAL - firewall.. 1 PLATE - stiffener, firewall . .1 BOLT - hex flange, self-tapping, 8 - 1.25 x 20 mm 9 WASHER - lock, 8 mm 9 RETAINER - push-in, plastic 2 BRACE - loader control bracket 1 WASHER-flat, 13/32 X 13/16 x 1/16 inch 6 NUT - hex, 3/8 inch NC 6 MIRROR - rear view, interior; 1 SCREW - self-tapping. Fillister head, No. 10 NC x 1 -1/4 inch 2 PLUG - button, 5/8 inch, if used. . .1 NUT - U-type, special, 6 mm 4 PLATE - bar, front console mounting to firewall 2 COVER - coat hook 1 ^ STRAP - velcro 1 STRAP - velcro . .1 VISOR - sun shade 1 . SCREW - self-tapping, pan Phillips, No. 10-16 x 3/4 inch. . . 3 SHIM - plate, visor mounting 1 TRIM-edge, bulk, 2946 mm (116 inch) long

1

NOTE: See page 9-77 for operator compartment to chassis mounting hardware.

Bur 7-3350


9-148

B9501151S

9-149

580 Super L Series 2 Loader Backhoe R E A R VIEW MIRROR POPS CAB MODELS - EXTERIOR REF. . PARTNO. "D102964 1 D142084 2 D142085 3 D142083 4 281-54712 5 D142086 6 R54682 7 413:-516 Al67037 8 - 9 ' 231-4115 D142144 10 11 413r412 12 231-1444

Bur 7-3350

. DESCRIPTION KIT - mirror, rear view BRACKET - mirror, right-hand upper BRACKET - mirror, left-hand upper, not shown BRACKET - mirror, lower SCREW - self tapping, hex washer head, 1/4 NC x 3/4 inch SUPPORT - mirror. MIRROR - rear view, exterior. BOLT - hex, 5/16 NC x 1 inch WASHER - nylon NUT - hex, self-locl
REQ'D. 1 1 .1 2 8 2 2 2 2 2 2 • • -6 • • • -6


9-150

B9409034S


9-151

SLOW MOVING VEHICLE EMBLEM REF. 1 2 3 4 5

PART NO. D52564 495-11028 126177 D123347 321-4311

Bur 7-3350

DESCRIPTION SPRING - emblem retaining WASHER - flat, 9/32 x 5/8 x 1/16 inch NUT - wing, 1/4 inch NC EMBLEM - plate and decal, slow moving vehicle DECAL-SMV emblem

REQ'D. 1 2 2 1 1


9-152

®580SuperL

AWARNING

0"

S •B

24-

^WARNING MriEMES COMTAIN *C10 AND CiPLOSlVE GAS EXPLOaON CAN nCSULT FROM SPARKS FLAMES, on WRONG CABL£ COMNECIIONS TO CONNECT

JUMPER CABLES OR CWAftCER SEE MAHUAUSl ro» THE conntCT pnoctDURE wtLUflt lO FOLLOW TMt ABOVE rNSTBuCTIONS CAN CAUSE

•C

AWARNIIMG ROTATING FAN AND BELTS.] CONTACT C A N I N J U R E . KEEP

CLEAR.

SCMOUS PERSONAL INJUR* OP OEATH

(3)

(3)

4

AWARNING KEEP CLEAR OF THIS AREA SWINaiNO BOOM CAN CRUSH. OPERATE BACKHOE FROM OPERATOR'S SEAT ONLY.

A

WARNING

WRONO iUHPIR C A S H CONNCCTIOK* TO t T M m TERyrNALS OR •HORTINQ TERMINAL* CAM THE

HACHIWI

CAUII

TO MOVI

SUDDEHIT O U T O P CONTROL. T O U CAN B l INjuneo on K U . E O . SHOWN IMTWO«IuTOM MANUAL TO C O N N I C T JUMPER CABLE! TO »TART THE ENClNi.

^

^

^

^

^ ikwARNING A DANGER

Starting in gear can cause death.Stvt angine only from operator seat with transmission comrolls) in NEUTHAL.

r-rrm

AWARNING » VOU aiAVlCI TMt MACHMI WTTH IMI MIAMI Un

AHMI RAttlO. ALWATI U H TNI SUPPOST

(a)

CAR CAUII IIHIOUS UUUR* OR MATH W TMl lOAOIB

ANHS AMI lOvMAte • » ACCIOIMT

•warning TO A V O I D INADVCRTAfTT M a V E M C N T . BEFORE OPIRATIhQ THI BACKHOE A L W A Y S PLACE THE FOUR SPEED TRANSMISSION AND FORWARD R E V E R S E CONTROL LEVER IN N E U T R A L AND t N G A Q E T H E P A R m w Q B R A K I

iJOOMMBfSflift.

iJOOMMCfSlM/L

BS97N177


9-153

DECALS REF. 1 1A 2 3 4 5 6 7 8 10 12 13 14 15 16 17 18 19 20 21

PART NO 182368A1 301343A1 183113A1 183112A1 183115A1 183114A1 183111A1 183110A1 183864A2 144194A1 321-6714 321-4481 321-6413 321-6671 321-1708 321-1707 321-3596 321-6872 321-7040 D150899

22 23

239880A1 239881A1

Bur 7-3350

DECAL• DECAL• DECAL• DECAL• DECALDECALDECALDECALDECALDECALDECALDECALDECALDECALDECALDECALDECALDECALDECALDECALbackhoe DECALDECAL-

DESCRIPTION REQ'D. 580 Super L 2 Series 2 2 Case, right-hand side of hood Case, left-hand side of hood Case, with right-hand stripes, standard dipper right-hand side Case, with left-hand stripes, standard dipper left-hand side Case extendahoe, right-hand Case extendahoe, left-hand Case, with right-hand stripe, rear closure panel, canopy models Warning, walk around and check your machine before starting Warning, batteries contain acid and explosive gas Warning, keep clear of this area, swinging boom can crush Warning, left-hand loader lift arm support strut usage Warning, right-hand chassis channel 0 - 2 - 4 , clam bucket opening indicator clam bucket position Warning, rotating fan and belts Warning, wrong jumper cable connections to starter terminals Danger, starting in gear can cause death Warning, to avoid inadvertant movement, before operating the powershift, left-hand side . powershift, right-hand side


9-154

IMPORTANT > Operators manual in box underneath this cover. Do not remove. Before operating, read all operators manual(s), safety and instructional signs on this machine. • It is your responsibility to follow all l a w s and regulations and to follow all instructions In the operators manual. I S e e your J I C a s e dealer for additional operators manuals, parts manuals and s e r v i c e manuals.

>>LOwN>AUX.HYD. I N C R E A S E c.

wnii iimcci ivam m i l IKl m m ton Ut i l t • i n ua ttmt HUT

Knm •Uf u « KUT IK •Ul

'Eu* MUT M l HUT U ELAYS

mut ana mm WEI

,„=,.,

iiuia KUI KITUl tUif W i n

Mm

S

"' USES

d)

®

BACKHOE Auoaunr

" p q * TO — •

KYUWUCS


9-155

DECALS REF. 1

PART NO. 144193A1

2 3 4

D137615 135183A1 284482A3

5 6

137290A1 137289A1

7 9 10

179683A1 D87870 D55216

11 11A 12 13 14

D80270 307348A1 128804A1 192450A1 192299A1

15 16 17 18 19 20

192300A1 197345A1 197346A1 284627A1 284479A1 299383A1

Bur 7-3350

DESCRIPTION REQ'D. DECAL - Important, operator's manual in box underneath this cover, glove box lid 1 DECAL - shuttle shift lever control pattern, on steering column cover 1 DECAL - instrument symbols, wipers and environmental control 1 DECAL - fuses and relays, loader control console fuse access panel cover 1 DECAL - two function loader control, lift and bucket control pattern 1 DECAL - three function loader control, lift, bucket and clam control pattern 1 DECAL - hand held auxilliary hydraulics, if used 1 REFLECTOR - red 2 PAD - anti-skid, 5 used on cab models, 11 used on canopy models, one used on hydraulic oil tank 5-11 PAD - anti-skid, 2 used on cab models, 3 used on canopy models 2-3 PAD - anti-skid, 700 mm (27-9/16 inch) long, fuel tank 2 STRIP - anti-skid 2 DECAL - clear vinyl, hood 1 DECAL - auxiliary hydraulics, at rocker switch on instrument panel, if used 1 DECAL - remote auxiliary hydraulics, operating instructions, if used 1 PAD - anti-skid, left-hand, ROPS canopy models 1 PAD - anti-skid, right-hand, ROPS canopy models 1 DECAL - backhoe auxiliary hydraulics, low flow - light on/hi flow - light off 1 DECAL - backhoe auxiliary hydraulics, hi flow/low flow 1 DECAL - backhoe auxiliary hydraulic control, mounts on control tower 1


9-156 HYDRAULIC FLUID

DIESEL FUEL

HYDRAULIC a FlUID^

AWARNING

lAVOlO CRUSHING DO MOT JUMP IF MACHINE TIPS:

If

!=#

USE SEAT BELT

HAIIIIMH SCHO tOLE

A WARNING (Si)

DO NOT C O A S T D O W N A HiLL WITH THE T R A N S M I S -

SiON IN N E U T R A L O R DO NOT EXCEED 2500 H P M WHEN DRIVING D O W N A H I L . e E F o n e DRIVING D O W N A H:LL. S H T T TO A L O W E R

GEAR A N D OfliVE S L O W L Y . Y O U

O R OTHERS

A R O U N D YOU CAN BE I N J U R E D IF T H E M.ACH NE IS OUT

OF CONTROL.

© lint M m 9 ffiu'Ki

—

A

CAUTION

".""iiiTr"'—

A C A U T I I O I V THIS I S AH INSULATED ROOF SYSTEM CONSULT YOUR DEALER B E F O R E UELDINO ON THE TOP OF THE CAB

(nitwcntitnu':!

AWARNIIMG

© DO NOT OPERATE

DO NOT R(MQV£ THIS TAC^

See Other Side

IIOIti/50t|

A WARNING PRESSURE ACCUMULATOR IH LOADER HYDRAUUC SYSTEM

A

WARNING

THE SPRINO IN THIS ASSEMBLY IS COMPRESSED. INCORRECT DI8ASSEMBLV CAN CAUSE INJURY. SEE SERVICE MANUAL.

A WARNING

REFER

tm

FROHT Of THE UACWHE OFf THE

GUUNO. TH£ lUCHIVE CM DROP CAU3H0

lenous iHJURY on DEATH.

BS97N179

ID

I H L SLHVCE

WAVJAL

PRECHARGE OflY VVTIH DRi liERT GAS K) HOT TURN THE R'DE COHTROL ON, V THE

LOADcn Ataa mo SUCKET ARE HOLDINO

JS97N179

DISCHARGE HYDRAialC PRE55LIRE PRIOR TO DlOCCTAECnNG HYDRAJI^C LINES. HYDHA'J-JC 0». UMlEfl FRESSUflE COtLD CAUSE r»iJUfiY

SUCH AS H:5H FUH;IY KITROGEN

REFER

TO THE SERVJCE

MANUAL

DISCHARGE AU GAS PRESSURE PRDR TO

D:SASEIi«.KGTHEACaJMUUTOa


9-157

DECALS REF. 1

PART NO 321-229

2 3 4 5 6 7

321-6376 321-230 321-6672 304940A1 321-6046 ':1^16534A1

8 9 . 10 ii 12 13

321-7030 D150900 112236A1 D149824 D149825 D149828

14

D149829

14A 15

L1;11356 D149826

15A

D149827.

16 17 18 19

186989A1 131-431 321-4614 255927A1

20

LI 29440

21

256318A1

22

321-6774

Bur 7-3350

DESCRIPTION REQ'D. DECAL - hydraulic fluid, used in production, for service order 321 -6376, item 2 DECAL - hydraulic fluid DECAL-diesel fuel DECAL - Warning, check and sen/ice cooling system DECAL - maintenance schedule, supplied by Parts and Components . . . . . . . . . DECAL - Warning, if you use the backhoe to lift a load that is too heavy 1-: KIT - decal, seat weight adjustment, includes instructions, included in seat assembly DECAL - Warning, do not jump - use seat belt DECAL - Warning, excessive speed can cause loss of machine control DECAL - Caution, this is an insulated roof system, cab models DECAL - standard backhoe control pattern, with foot swing, upper DECAL - extendahoe control pattern, with foot swing, upper DECAL - standard backhoe control pattern, with hand swing, upper, left-hand side of control console DECAL - standard backhoe control pattern, with hand swing, upper, right-hand side of control console DECAL - boom lock DECAL - Caution, operate backhoe from seat position only, lower, for all models, with foot swing backhoe controls and standard backhoe models with hand swing DECAL - Caution, operate backhoe from seat position only; lower, for extendahoe backhoe models with hand swing EMBLEM-Case NUT - push-dn type TAG - do not operate DECAL - Warning, do not turn the ride control on, if the loader arms and bucket are holding the front of the machine off the ground, mounts on console by ride control switch, models with ride control, if used DECAL - hydraulic accumulator application instructions, mounts on accumulator, models with ride control, if used DECAL - Warning, pressure accumulator in loader hydraulic system, mounts on accumulator mounting plate, models with ride control, if used DECAL - Warning, the spring in this assembly is, seat spring



10-1

NUMERICAL INDEX PART NO.

PAGE

A10454 A13240 A14141 A141451 A15672 A156873 A165395 A165860 A166057 A166057 A167037 A170241 A170241 A170309 A170467 A171099 A171940 A172116 A177435 A178706 A180163 A184545 , A184614 A186171 A186182 A186183 A186186 A186193 ^ A186256 i A187504 A187542 A187575 A187714 A187873 A187873 A187899 A187901 A187903 A187904 A187906 A187909 A187911 A187912 A187914 A187917 A187923 A187965 A187990 A1,87990 A188028 Ai89154 A189284 A191114 A20058 A20058 A23870 A27602 A28230 A30013 A30881 A30881 A30881 A30881

4-5 44 8-63 25 8-3 8 9-77 . 24 6-23 23 6-5 6 2 9-131 3-5 4-11 2 4-11 17 9-149 8 2 2-3 2-5 9 2-15 4 2-11 4 2-3 15 2-13 6 2-13 7 3-7 2 6-23 24 9-117 18 2-3 30 9-145 15 9-129 4-7 24 4-7 18 4-7 15 4-7 25 9-129 1 4-7 13 4-43 5 4-43 11 1 9-131 4-7 4-9 4 4-7 -12 4-7 17 4-7 1 4-7 9 4-7 2 9-129 17 4-35 2A 2 4-35 4-35 4 4-7 11 2-13 10 4-27 4-17 11 • 7-7 , 3 2 7-13 23 2-13 1 9-145 6 4-27 .6-53 2 6-53 2 4-43 1 5-15 28 34 5-15 8-3 16 11 9-9 9-29 15 9:33 5 9-35 26

Bur 7-3350

REF.

PART NO.

PAGE

A33509 A38208 A38208 A38261 A38261 A41264 A41264 A41852 A42465 A42561 A45007 A45054 A45093 A46948 A46950 A47123 A47125 . A47127 A47128 A47129 A47130 A47230, A47232 A47233 A47234 A47235 A47236. A47237 A47238 A47239 A47240 A47241 A47242 A47243 A47244 A47247 A47249 A47688 A48041 A48041 A48041 A49667 A52216 A61447 A61448 A61449 A62209 A65544 A66759 A77310 A77313 A77314 A77405 A77405 A77406 A77406 A77416 A77424 A77429 A77429 ^ A77465 A77465 A77466

9-59 5-17 5-19 5-19 5-19 4-37 4-39 3-17 2-9 9-125 4-27 9-107 4-27 4-3 4-5 4-27 4-27 4-3 4-3 4-5 4-5 4-5 • 4-3 4-3 4-3 4-3 4-3 4-5 4-5 4-5 4-3 4-3 4-5 4-3 4-5 4-5 4-5 4-27 6-13: 6-39 6-41 9-145 4-33 5-17 5-17 5-17 9-11 5.-3 5-17 7-7 4-21 4-21 2-41 2-43 2-41 2-43 2-21 2-41 2-39 2-41 2-41 2-47 2-47

REF.

29 5 7 3 , 6 9 5 14 3 11 5 15 2 39 18 19 13 10 36 38 16 17 18 19 20 33 34 31 27 28 35 30 .32 8 11 6 2 3 13 12 11 10 14 5 1 14 19 18 44 11 45 12 30 17 34 43 11 11

PART NO.

A77467 A77468 A77469 A77472 A77473 A77474 A77475 A77476 A77477 A77478 A77479 A77490 A77505 A77512 A77673 A77673 A77720 A77736 A77775 A77782 A77783 A77809 A77810 A77817 A77840 A77841. A77864 A77870 A77870 A77887 A77889 A77890 AC77752 B17575 B17575 B17575 B17575 B17575 B17575 B17576 B93222 BMF28S BMF31E D102964 D103626 D120450 D120450 D120561 D121047 D121152 D121152 D121194 D121385 D121608 D123347 D123655 D123684 D123684 D123806 D123865 D124528 D124529 D124530

PAGE

REF.

2-47 11 2-47 11 2-47 11 11 2-43 2-43 12 2-43 11 2-43 12 11 2-43 12 2-43 11 2-43 2-43 12 2-31 6A 2-39 3-17 26 2-31 2-41 48 3-17 2 2-33 3-17 13 2-39 6 2-35 2 2-43 23 2-43 26 2-17 19 2-43 12 2-43 12 2-51 2-41 46 2-49 2-41 2-43 13 2-43 18 2-39 6-5 6-7 6-9 6-13 6-15 . 6-17 9-81 • 35 5-17 4-15 1 1 4-13 9-149 5-15 14 9-49 7 9-55 4-19 19 9-11 22 4-29 6 4-37 9-13 6 8-59 29. 7-13 12 9-151 4 5-15 7 5-15 6 6-3 io 5-15 16 5-15 29 7-7 ,19 7-7 13 7-7 23



10-2


D124857 D125079 D125223 D125340 D125341 D126198 D126198 D126204 D126205 D126409 D126821 D127018 D127167 D127167 D127167 D127168 D127168 D127172 D127172 D127172 D127172 D127172 D127172 D127335 D127507 D127542 D127542 D128018 D128020 D128021 D128022 D128310 D128402 D128745 D129227 D129264 D129264 D129264 D129641 D129747 D129967 D129968 D129969 D129974 D132076 D132494 D132494 D132681 D132681 D132682 D132682 D132895 D132982 D132982 D132982 D132982 D132982 D133428 D133632 D133632 D133865 D134737 D134900

Bur 7-3350

PAGE

REF.

3-9 4-13 5-19 5-15 5-15 9-123 9-123 9-113 9-113 4-15 4-23 4-13 9-55 9-57 9-59 9-55 9-59 9-55 9-55 9-57 9-57 9-59 9-59 4-23 5-15 9-11 9-77 9-131 9-131 9-131 9-131 4-19 2-13 9-129 9-53 9-15 9-17 9-19 9-53 7-13 9-123 9-123 9-123 9-123 9-13 9-49 9-59 4-29 4-33 4-29 4-33 9-83 5-7 7-9 8-39 8-43 9-139 9-45 9-49 9-59 9-59 4-21 9-41

8 7 1 17 18 22 25 3 4 4 19 10 13 38 21 11 19 14 18 39 43 22 33 24 19 2 3 10 11 21 6 9 16 3 2 2 11 6 13 12 21 24 7 17 16 2 1 2 10 39 22 17 50 24 5 21 7 24 6

PART NO.


PAGE

REF.

9-133 4-29 4-37 9-117 9-47 9-47 9-49 9-47 9-47 9-49 9-59 9-47 9-49 9-59 7-9 9-43 9-47 9-3 9-37 7-7 9-49 5-15 4-11 4-47 9-11 9-105 4-19 9-155 8-3 6-3 6-19 6-25 6-69 4-21 9-51 9-55 5-15 9-55 9-55 9-57 9-59 8-11 8-13 8-13 8-17 8-17 8-65 8-67 8-69 8-69 8-69 9-79 9-63 9-65 9-65 9-67 9-67 9-69 9-71 9-71 6-53 6-55 6-53

15 5 16 5 6 12 4 26 19 5 24 20 6 2 7 25 17 11 6 13 2 12 9 16 18 2 17 13 41 13 20 30 2 3 9 19 44 34 8 6 15 7 14 24 29 8 12 22 32 7 7 7 7 7 7 7 7 4 3 5

PART NO.


PAGE

REF.

6-55 9-77 9-77 5-15 4-41 9-63 9-65 9-65 9-67 9-67 9-69 9-71 9-71 9-63 9-65 9-65 9-67 9-67 9-69 9-71 9-71 8-141 9-55 7-7 9-59 9-91 9-73 8-37 9-55 9-61 9-55 9-61 8-139 9-59 9-67 9-71 9-149 9-149 9-149 9-149 9-149 9-45 8-27 9-45 8-11 8-21 8-23 8-25 8-59 6-41 6-47 6-61 6-67 6-61 9-61 9-147 9-57 5-17 9-45 9-45 8-7 8-21 8-53

2 12 21 1 12

15 8 9 28 32 23 20 37 22 39 15 11 4 4 3 1 2 5 10 20 10 15 20 27 21 32 15 21 16 5 2 18 56 16 30 4 13 31 10 14 46



10-3


PAGE

REF.

D143412

8-33

31

D143416

9-41

5

D143417

9-53

D143417

9-91

PART NO.

PAGE

REF.

0148947

9-35

2

0148962

3-7

6

8

0148992

9-29

25

0148993

9-29

PART NO.

PAGE

REF.

0150493

9-29

24

0150503

9-31

45

7

0150608

9^55

15

19

0150608

9-59

30

D143417

9-91

30

0148994

9-29

18

0150619

9-57

34

D143417

9-139

29

0149033

9-45

25

0150633

7-13

11

D143417

9-141

20

0149079

9-59

16

0150781

8-121

D143422

8-5

32

0149239

9-47

32

0150810

8-121

D143422

8-43

54

0149262

9-31

46

0150899

9-153

D143426

8-33

29

0149287

9-7

36A

0150900

9-157

9

D143427

9-139

27

0149287

9-9

4

0151034

9-13

15

D143427

9-141

, 18

0149287

9-31

37

0151065

9-47

21

D143430

8-9

18

0149287

9-33

11

0151069

9-77

5

D143591

9-53

14

0149287

9-37

3

0151070

9-77

6

D143714

9-91

9

0149287

9-41

11

0151071

9-49

11

D143715

9-91

8

0149288

7-13

20

0151073

9-47

7

,0143723

9-53

10

0149288

9-3

26

0151074

9-47

8

%143735

9-53

17

0149288

9-7

36

025279

9-45

10

D143797

8-7

5

0149288

9-29

23

025279

9-45

14

D143797

8-7

9

0149288

9-31

48

025279

9-57

31 7

;

21

D143797

8-39

19

0149288

9-37

025279

9-73

D143797

8-43

55

0149295

9-31

34

026002

9-45

9

D143830

4-11

6

0149295

9-37

9

028648

9-45

12

D144423

9-47

35

0149298

9-57

32

030933

9-63

12

D144592

9-53.

4

0149725

6-5

2

030933

9-65

12

9-65

4

0149726

6-5

4

D30933

9-65

12

D145061

9-67

4

0149737

6-9

8

030933

9-67

12

D145061

9-71

4

0149738

6-9

6

030933

9-67

12

D145062'

9-69

4

0149739

6-9

030933

9-69

12

D;I 4 5 3 6 7

2-13

0149824

9-157

11

030933

9-71

12

D146035

8-21

24

0149825

9-157

12

030933

9-71

12

D146035

9-83

.11

0149826

9-157

15

031140

9-19

2

D146288

9-55

26

0149827

9-157

„ 15A

034033

8-45

2

'Dl46288

9-61

49

0149828

9-157

13

034666

9-29

16

4-27

11

0149829

9-157

14

035009

6-23

32

9-65

3

0149860

6-19

036179

9-89

8

D146420

9-65

3

0149860

6-69

036179

9-125

17

pi 45060

s

D146335 D146420

•

.

2

.

7

D146420

9-67

3

0149866

9-25

9

036264

2-9

11

D.I 4 6 4 2 0

9-67

3

0149867

9-25

10

D36505

5-15

15

D146420

9-69

3

0149868

9-25

12

036669

9-121

15

D146421

9-65

2

0150032

9-41

13

037495

9-65

11

0146421

9-65

2

0150053

8-59

3

037495

9-65

11

0146421

9-67

2

0150054

8-59

2

037495

9-67

11

0146421

9-67

2

0150080

9-55

17

037495

9-67

11

0146421

9-69

2

0150080

9-59

32

037495

9-69

11

0146588

9-65

1

0150099

8-21

25

037495

9-71

11

0147166

4-19

,17

0150121

9-55

10

037495

9-71

11

0147247

9-65

1

-0150121

9-59

17

037495-

9-73

2

0147249

9-65

4

0150122

9-55

16

037614

9-57

29

0147383

4-11

11

0150122

9-57

41

038435

8-9

23

0147383

4-11

14

0150122'

9-59

31

038648

8-19

20

0147383

4-11

33

0150155

5-15

20

D38648

8-37

26

0147383

4-17

2

0150348

9-67

1

038858

8-141

12

0147383

9-127

12

0150364

9-67.

1

038907

9-45

3

0147383

9-145

27

0150365

9-69

1 •

039093.

9-63

5

0147383

9-147

8

0150377

9-103

12.

039093

9-65

5

0147409

9-63

4

0150377

9-103

20

039093

9-65

5

0147410

9-63

3

0150391

9-103

15

039093

9-67

5

0147411

9-63

2

0150391

9-103

•23

039093

9-67

5

D147418

9-63

1

0150397

9-29

9

039093

9-69

5

•

-

i

0147773

8-59,

26

0150434

9-29

13

D39093

9-71

5

0148108

4-17

10

0150435

9-29

12

039093.

9-71

5

01.48108

7-7

, 31.

0150486

9-29

17

039118

9-35

11

Bur 7-3350



10-4



Bur 7-3350

PAGE

REF.

9-45 4-11 5-7 8-19 8-21 8-31 8-35 8-37 9-63 3-5 9-81 9-81 7-13 8-47 9-73 9-63 9-65 9-65 9-67 9-67 9-69 9-71 9-71 9-45 9-19 9-19 9-19 9-63 9-65 9-65 9-67 9-67 9-69 9-71 9-71 8-21 8-23 8-25 8-27 8-29 8-33 8-37 2-3 8-21 8-23 8-25 8-27 8-29 8-33 8-37 9-151 9-73 9-81 9-155 4-13 5-15 9-29 9-35 9-43 9-147

17 19 25 6 23 37 48 13 11 37 37 42 2 6 4 10 10 10 10 10 10 10 10 6 7 15 19 8 8 8 8 8 8 8 8 6 6 6 6 6 6 6 25 7 7 7 7 7 7 7 1 5 43 10 8 25 4 6 2 2

5-15 9-45 8-57

36 16 7

PART NO.

D67297 D71342 D71343 D71344 D71346 D72371 D72372 D73383 D73741 D74182 D74949 D75103 D75465 D77182 D80270 D82804 D82805 D82806 D83306 D83485 D83885 D86664 D87870 D88052 D88052 D88427 D93716 D95096 D95142 D95142 D95143 D95143 D95143 D95144 D95144 D95145 D95146 D95146 E l 35750 E l 35762 E l 35777 E l 35785 E135810 E43769 E46524 E46560 E46561 E47027 E47027 E47238 E47239 E47240 E49497 E49498 F13537 F22426 F42827 F42827 F42827 F42827 F42827 F42827 F44748

PAGE

8-3 4-27 4-27 4-27 4-27 5-15 5-15 4-15 2-13 8-53 5-17 5-17 3-3 8-25 9-155 5-11 5-11 5-11 9-73 4-13 3-3 9-53 9-155 9-139 9-143 9-45 9-147 9-9 5-13 8-129 8-127 8-131 8-143 8-133 8-135 8-137 8-139 8-141 6-59 6-63 6-61 6-61 7-5 9-127 9-127 9-127 9-127 9-115 9-147 9-127 9-127 9-127 9-39 9-39 8-119 4-25 3-5 4-25 9-81 9-89 9-125 9-147 9-121

REF.

29 12 13 14 16 32 35 5 14 45 8 12 10 11 26 24 22 3 2 28 15 9 32 5 11 4 13 8 5 5 5 4 5 5 7 5 5 18 8 3 8 7 28 23 11 17 29 2 3 4 4 3 38 21

19

PART NO.

F44881 F44881 F44883 F44883 F45165 F45165 F64046 F64198 F64198 F64198 F64342 F64519 G100440 G100444 G100444 G100444 G100448 G100449 G100449 G100449 G100710 G100711 G101066 G101533 G101533 G102090 G102090 G102092 G102285 G102286 G102287 G102288 G102288 G102288 G102424 G102425 G102425 G102425 G102426 G102427 G102711 G102711 G102711 G102711 G102711 G102711 G102711 G102711 G102711 G102711 G103862 G103862 G103862 G103862 G103862 G103862 G103862 G103862 G103862 G104439 G104454 G104989 G104989

PAGE

9-119 9-121 9-93 9-119 9-117 9-119 9-121 9-117 9-119 9-123 9-117 9-133 8-135 8-129 8-131 8-143 8-135 8-129 8-131 8-143 8-141 8-141 8-119 8-133 8-135 8-137 8-139 8-139 8-135 8-141 8-127 8-129 8-131 8-143 8-129 8-127 8-131 8-143 8-137 8-139 8-79 8-81 8-85 8-99 8-101 8-103 8-105 8-109 8-113 8-115 8-79 8-81 8-85 8-99 8-101 8-105 8-111 8-113 8-115 5-13 5-13 8-133 8-137

REF.

10 9 10 23 11 6 3 10 8 15 13 8 16 15 17 14 17 16 18 15 18 19 32 6 6 22 19 18 15 17 14 14 16 13 6 6 6 5 8 6 5 5 5 5 5 5 5 5 5 5 22 25 19 15 19 19 37 15 15 15 16 18 24



10-5


PAGE

G104989 G104990 G105187 G106395 G106396 G106398 G106409 G106410 G106410 G106410 G106410 G1064,10 G106410 G106410 . G106425' G106808 G106810 G106813 ,G106817 G106832 G107251 G107251 G107251 G107251, G107251 . G107251 G107277 G107447 G107720 G107720 G107720 G107721 G107780 G107780 G107780 G107786 G107921 G107970 G107970 G1085j12 (3108518 G108556 G108630 G108723 G108723 G108805 G108866 G108867 G108870 G108899 G108899 G108900G108902 G108911 G108912 G108913 G108914 G108956 G108957 G109127 G109295 G109298 G109298

8-141 8-139 5-13 8-81

Bur7-3350

REF.

PART NO.

21 G109298 21 G109299 14 G109384 ,8 ' G109391 9 G109391 8-81 8-81 12 G109391 8-115 29 G109391 8-85 9 G109391 7 8-99 G109449 8-101 7 G109449 7 8-105 G109449 8-109 7 G109449 7 8-113 G109449 7 8-115 G109627 • 8-81 • 14 : G109630 5-13 2 G109644 5-13 7 G109646 5-13 18 G109881 5-13 6 G109884 5-13 4 G109884 8-73 10 G109899 8-75 -11 G109908 8-89 10 G109964 11 8-91 G109971 8-93 11 G110045 8-95 11 G110077 12 8-143 G110077 8-79 9 G110077 17 G110077 5-5 1 5-13 G110269 5-15 11 G110391 5-13 G110391 8-79 16 G110467 8-81 16 G110468 8-119 19 G110519 8-111 G110529 5-13 9 G110530 8-137 14 G110531 8-139 12 • G110569 8-129 3 G13609 8-129 13 G15215 8-77 12 G32122 8-119 6 G32129 8-109 17 G32176 8-119 26 G32176 8-75 13 G32303 8-77 7 " G32303 8-77 9 G32303 12 8-73 G33075 8-91 13 G33075 8-93 13 G33075 8-89 12 G33075 2 G33075 8-97 8-119 15 G33075 8-119 13 G33075 8-119 11 G33075 8-119 9 G33075 8-119 37 G33075 8-119 39 G33080 8-81 G33080 10 8-79 10 G33080 8-129 .10 G33080 8-131 11 G33080

PAGE

REF.

8-143 9 8-135 10 8-81 •15 8-79 23 8-87 8-105 8-107 .8-115 8-87 8-105 8-107 8-111 8-115 8-103 8-103 23 8-83 2 8-83 4 8-129 4 4 8-131 8-143 3 8-135 4 8-141 6 8-109 15 8-109 18 5-13 8-99 8-101 8-107 8-121 8-137 21 8-119 3 8-119 5 8-121 8-103 21 8-133 4 8-133-- 15 8-133 16 8-133 . 14 8-139 16 . 5-11 25 5-17 9 8-127 10 5-13 11 8-133 10 24 8-135 8-127 18 8-131 20 8-135 19 8-79 6 8-81 6 8-85 6 8-99 6 8-101 6 8-103 .7 8-105 6 8-109 6 8-113 6 8-115 6 8-85 10 8-99 10 8-101 10 8-103 9 8-105 10

PART NO.

G33080 G33080 G33080 G33112 G33122 G33122 G33122 G33122 G33965 G33965 G33965 G33965 G33965 G33965 G34458 G34458 G34458 G34458 .G34458 G34458 G34463 G34937 G34937 G34937 G34937 G35540 G35540 G35540 G35540 G35540 G35540 G35540 G35540 G35540 G35540 , G35540 G35540 G35540 G35540 H275784 H422758 H422766 H422774 H433285 H434163 H71514 J280911 J282406 J283333 J283333 J283336 J283338 J283767 J283767 J330478 J527759 J528177 J528204 J528221 J531582 J531598 J531670 J532195

PAGE

8-109 8-113 8-115 8-97 8-81 8-85 8-103 8-113 8-73 8-75 •'8-89 . 8-91 8-93 .8-95 8-79 8-85 8-97 8-101 8-105 8-109 8-103 8-97 8-101 8-105 8-109 8-77 8-81 8-85 8-87 8-99 8-101 8-103 8-103 8-105 8-107 8-11.1 8-113 8-115 8-121 2-13 4-27 4-27 4-27 9-49 8-3 9-49 2-35 3-15 2-33 2-41 2-33 2-33 2-41 2-51 2-39 2-25 2-27 2-27 2-27 2-25 2-25 2-25 2-27

REF.

10 10 10 4

11 12 11 12 12 12 25' 21 11 13 13 13 6 9 11 11 11 16 20 14 4 19 23 13 19 23 36 23 19 19 4 13 3 4 2 24 26 7 11 8 2 47 2 2 23 8 17D 22 2 4 5 19 20 17 7



10-6


J535001 J535203 J535800 J535971 J537560 J537560 J575205 J580234 J678912 J678921 J678923 J802358 J802422 J802423 J802746 J802747 J802747 J802764 J802765 J802798 J802798 J802998 J818823 J818824 J823921 J900068 J900068 J900227 J900227 J900242 J900245 J900250 J900257 J900257 J900299 J900677 J900706 J900706 J900919 J900955 J900956 J900958 J900967 J901049 J901097 J901097 J901395 J901706 J901706 J901706 J901919 J902343 J902425 J902425 J902469 J903035 J903089 J903102 J903242 J903380 J903380 J903463 J903475

Bur 7-3350

PAGE

2-25 2-27 2-25 2-25 2-27 3-15 2-25 2-25 2-39 2-39 2-39 2-17 2-47 2-47 2-47 2-41 2-47 2-47 2-47 2-25 2-27 3-17 2-23 2-23 2-49 2-39 2-39 2-17 2-37 2-35 2-35 2-35 2-19 2-39 2-35 2-31 2-35 2-35 2-47 2-39 2-39 2-39 2-39 2-31 2-35 2-49 2-45 2-47 2-47 2-47 2-21 2-39 2-31 2-51 4-9 3-15 4-9 2-41 2-37 2-49 3-13 2-19 2-19

REF.

21 10 24 18 1 1 1 17B 17A 16

41

6 7 13 3 15 4 5 19 20 5 9 13 6 2 23 27 10 10 7 9 2 6 8 2 14 5 5 5 1 14 12 13 6 13 7 31 3 9 7 19 20

PART NO.


PAGE

2-51 2-23 2-41 2-33 2-43 2-19 2-35 2-47 2-41 2-41 2-21 2-45 2-35 2-35 2-43 3-13 2-19 2-41 2-31 3-13 3-11 2-21 2-49 2-43 3-11 2-35 2-29 2-35 2-49 3-13 3-19 2-41 2-51 2-41 2-51 2-21 2-35 2-33 2-21 2-41 2-17 2-19 2-43 2-33 4-7 4-7 2-29 2-29 2-49 3-19 2-45 2-41 2-17 2-35 2-35 2-17 3-11 2-17 2-45 2-51 2-19 3-17 2-45

REF.

1 9 19 9 7 13 13 7 36 26 4 13 14 15 3 13 15 25 3 8 20 2 4 6 16 13 4 10 10 3 28 14 32 10 6 12 6 5 24 7 12 1 7 27 28 3 2 11 2 6 40 10 25 21 6 19 11 5 16 21 4 11

PART NO.


PAGE

2-23 2-19 2-51 3-11 2-33 2-17 2-43 2-49 2-19 3-17 2-19 2-51 2-29 3-11 3-11 2-35 3-13 3-13 2-21 3-11 3-11 3-15 3-11 3-11 2-29 3-17 2-41 2-19 2-51 2-19 3-13 3-13 3-13 2-17 2-29 2-41 2-47 2-47 2-47 2-23 2-49 3-15 2-19 2-23 3-15 3-15 2-31 3-13 2-39 2-31 2-35 2-35 2-35 3-13 2-35 2-35 2-43 2-29 4-9 2-35 2-49 2-35 2-45

REF.

8 14 5 3 10 5 5 12 18 23 11 4 9 10 7 1 15 12 7 9 8 14 14 18 6 25 35 3 2 1 18 16 17 17 42 6 6 6 5 3 12 10 14 4 5 10 11 12A 9 17 17 30 14 9 10 8 11 3 8A 2 18


10-7



.

J923044 J923262 J923331 J923331 J923387 J924147 J924148 J924725 J924726 J924962 J924962 J925009 J925186 J925195. J925234 J925680 J925953 J925955 J926047 J926113 J926700 J926738 J927155 J927330 J927622 J927633 ,J927633 ;J927948 J928404 J928406. J928406 ., J928493 J928493 J928759 J928759 J928981 J928989 J929027 J929028 J929393 J929394 J929395 J929396 J929456 J929457 J929457 J929490 'J929490 . J929751 J929751 J929792 J929792 J929885 J930139 J930152 J930152 J930336 J930590 J930886 J930906 J930906 J930993 J930993

Bur 7-3350

PAGE

2-17 2-35 2-33 2-49 2-33 2-31 2-31 3-11 3-11 2-19 2-19 2-29 2-17 2-17 2-45 2-41 2-3 3-11 2-39 3-15 2-35 3-15 2-37 2-35 2-29 3-11 3-13 2-39 2-33 . 2-33 2-49 2-43 2-51 2-41 2-51 3-17 2-41 2-43 2-37 3-13 3-13 3-13 3-13 3-17 2-29 2-51 3-13 3-19 2-19 2-51 2-29 2-51 2-37 2-41 3-13 3-17 2-31 3-17 2-45 2-33 2-49 2-51 3-17

REF.

PART NO.

8 31 11 1 15 8 11 17 11 7 8 7 16 14 3 22 31 1 12 3 7 11 4 ,1 4 12 6 4 3 5 15 10 9 20 18 3 37 2 7 2 3 4 5 40 8 15 9 - 1 16 6 10 12 1 18 1 1 1 38 1 4 8 19 37

J931062 J931348 J931348 J931349 J931350 J931350 J931351 J931351 J931450 J931605 J931605 J931623 J931784 J931804 J931970 J932012 J932035 J932096 J932096 J932120 J932296 J932529 J933026 J933220 J933250 J933254 J933291 J933648 J934022 J934190 J934429 j940059 J941472 J941476 J942581 J942914; J942914 JG537562 JC901569 JC908031 JG926202 JC927330 JC929490 JC930153 JR802798 JR908031 JR927330 JR929490 JR930152 JR930336 JR933648 JR942581 K260177 K260177 K261014 K261014 . K261065 K261065 K262143 K262143 K395027 K395075 K395082

PAGE

:

REF.

2 3-11 17 2-51 3-11 4 2-31 4 2-23 10 2-49 6 2-19 5 2-51 3 3-1722 2-21 8 2-49 5 2-35 32 1 2-23 2-23 2 2-23 12 2-39 1 3-11 ? 16 3-11 15 3-17 6 4 2-19 2-39 170 3-17 30 2A 2-23 2-39 3-11 13 3-11 5 3-17 28 2-39 3-17 43 2-41 27 2-29 3 2-37 2 3-17 27 2-47 9 2-47 2-29 12 2-51 11 2-25 2-47 2-43 2-31 2-35 3-19 3-17 2-25 2-43 2-35. 3-19 3-17 2-31 2-39 2-47 6-29 5 6-31 5 6-17 4 .6-63 4 6-17 3 6-63 3 6-17 9 12 6-63 12 6-15 6-15 8 6-67 8

PART NO.

K395086 K395087 K395090 K395090 K395091 K395093 K395093 K395101 K395131 K691987 K691987 L I 00659 L I 01998 L105735 L111356 L11182 L112081 L112081 L112087 L112087 L112088 L112088 L112089 L112089 L112090 L112090 L112090 L112090 L I 26767 L I 29440 L I 29440 L I 5401 L I 7985 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 LI 8 3 3 7 , L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337

PAGE

6-15 6-15 6-17 6-63 6-13 6-13 6-67 6-67 6-67 2-3. 9-83 8-57 8-57 8-57 9-157 7-13 9-129 9-131 9-129 9-131 9-129 9-131 9-129 9-131 9-129 9-129 9-131 9-131 2-3 8-123 9-157 9-9 9-139 2-7 2-13 3-3 3-7 4-11 4-19 4-31 4-41 4-47 5-7 5-7 5-7 6-21 6-57 6-57 7-9 7-13 8-5 8-21 8-25 8-27 8-29 8-33 8-37 8-39 8-43 8-45 8-57 8-59 8-63

REF.

, 13 • 6 8 10 21 16 9 25 15 24 9 5 9 8 14A 19 14 19 11 13 10 12 12 17 5 13 9 18 14 20 12 22 14 17 22 12 28 26 22 5 6 22 32 41 10 8 23 23 28 39 13 20 20 19 19 19 18 51 7 6 • 17 36


10-8



PAGE

REF.

L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L I 8337 L26209 L30878 L30881 L30888 L30889 L30893 L32318 L35368 L50062 L50062 L54563 L54563 L59682 L60224 L60224 L60539X L71879 L71879 L72776 L77821 L79937 N13505 N13542 N13543 N13545 N13546 N14112 N14225 N14250 N14283 N14284 N14285 N14330 N14367 N14407 N14408 N14410 N14465 N14466 N14763 N14784 N6755 N6807 N6836 N6941 N7802 N8356 N8358 N8359 N8360 N8361 N8361 N8362 N8362

8-65 8-69 9-7 9-107 9-137 9-139 9-141 9-143 9-145 7-7 5-11 5-9 5-11 5-11 5-11 8-71 5-11 9-139 9-139 9-29 9-33 2-13 4-31 9-121 2-13 4-11 4-19 2-13 9-103 8-15 6-7 4-27 4-27 4-27 4-27 9-129 4-27 5-11 4-37 4-33 4-33 8-3 6-5 6-15 6-15 6-11 9-133 9-133 5-11 7-11 8-125 4-27 4-37 8-125 9-109 9-129 9-129 9-129 9-129 9-129 9-131 9-129 9-131

23 18 41

Bur 7-3350

21 25 17 13 5 7 16 5 6 4 21 2 19 4 12 14 1 16 23 8 21 2 4 39 11 7 6 1 10 8 21 10 4 12 13 3 5 7 3 11 10 10

9 3

9 7 2 6 4 8 3 5

PART NO.

N8362 N9025 P2745466 P2930467 P3034505 P3533055 P3533055 R21391 R32119 R46493 R46493 R46493 R47941 R52408 R52415 R52440 R52483 R52483 R52735 R52879 R52880 R52881 R52882 R52883 R52884 R52917 R53000 R53444 R53562 R53562 R53634 R53755 R54047 R54504 R54682 R55000 R55001 R58418 R58418 S I 09444 S I 09445 S110169 S110170 8115351 S118383X S300976 8301064 8301065 S80928 888754 888756 894643 894643 8T205A 8T205A T34857 T34857 W10478 W16323 100-1125 100-1647 100-1647 100-1647

PAGE

REF.

PART NO.

PAGE

REF.

9-131 8-125 6-47 6-67 6-61 6-45 6-47 2-9 9-49 8-5 8-19 8-43 9-43 9-131 9-125 9-125 9-125 9-139 9-121 9-117 9-117 9-117 9-117 9-117 9-117 9-117 9-119 9-117 9-117 9-119 9-139 9-133 9-119 9-129 9-149 9-117 9-117 9-103 9-103 8-127 8-127 5-11 5-11 5-9 8-9 6-61 6-5 6-5 9-145 8-71 8-71 8-129 8-143 6-39 6-47 4-37 4-39 4-27 8-71 8-79 8-85 8-99 8-101

7

100-1647 100-1647 100-1647 100-1647 100-1647 100-21118 100-21237 100-21250 100-21315 100-2156 100-3331 100-3337 100520A1 100522A1 100529A1 100532A1 100533A1 100552A1 100553A1 100554A1 100555A1 100556A1 100557A1 100557A1 100557A1 100557A1 100557A1 100559A1 100561A1 100562A1 100696A1 100747A1 100748A1 100748A1 100753A1 100760A1 101479A1 101531A1 101631A1 102-1387 102649A1 102761A1 102761A1 102765A1 103-11237 103-1437 103-16175 103-16175 103-16175 103-16175 103-16175 103-16175 103-16175 103-16175 103-16175 103-16175 103-16175 103-16200 103-1687 103-3350 103-3350 103670A1 103670A1

8-103 8-105 8-109 8-113 8-115 8-119 5-15 2-17 8-135 8-119 9-119 9-123 6-5 6-5 6-7 6-7 6-7 6-13 6-13 6-13 6-13 6-13 6-13 6-29 6-31 6-59 6-67 6-13 6-13 6-13 9-11 6-47 6-27 6-47 6-47 6-59 8-35 4-43 9-55 5-9 9-59 9-3 9-5 9-35 9-51 9-5 9-45 9-45 9-51 9-55 9-55 9-55 9-57 9-57 9-59 9-61 9-61 9-47 5-15 9-11 9-43 8-33 8-55

8 9 9 9 9 18 31 9 13A 40 27 20 12 9 4 3 8 5

21 3 9 35 20 9 8 31 7 56 14 20 10 9 13 9 18 6A 6 5A 5 7A 7 8 15 4 2 2 5 22 15 6 17 17A 13 21 15 16 31 27 2 7 18 15 7A 16 17 18 17 1 6 2 2 17 24 11 8 9 9

18 4 22 8 8 1 7 6 13 19 3 12 9 14 17 21 40 9 4 18 12 23 19 28 15 4 8 33 5 23 27 33 36 14 40 50 18 38 29 8 36 18



10-9


104587A1 104588A1 104589A1 104824A1 104907A1 106974A1 106989A1 106990A1 107071A1 107124A1 107230A1 107232A1 107233A1 107234A1 107949A1 108088A1 108088A1 108088A1 108335A1 108336A1 108366A1 108513A1 108794A2 108797A1 108864A1 108923A1 108924A1 108936A2 108938A2 108963A1 109080A1 109080A1 109081A1 109081A1 109131A1 109132A1 109239C2 109268A1 109511A1 109686A1 109879A1 109879A1 110307A1 111282C1 111522A1 111583A1 111588A1 111589A1 111592A1 111593A1 111594A1 111596A1 111597A1 112236A1 112366A2 112366A2 112366A2 112370A3 112380A1 112380A1 112380A1 112382A1 112432A1

Bur 7-3350

PAGE

REF.

4-3 4-3 4-5 9-11 6-53 9-123 9-35 9-35 6-67 9-77 9-113 9-113 9-113 9-113 9-121 9-3 9-5 9-5 8-33 8-33 4-43 9-113 9-115 9-115 9-35 9-35 9-35 9-119 9-119 9-115 4-31 4-35 4-31 4-35 9-35 9-35 9-137 9-11 4-41 6-15 9-83 9-93 8-129 9-125 9-11 8-71 8-71 8-71 8-71 8-71 8-71 8-71 8-71 9-157 8-11 8-127 9-11 8-135 9-3 9-5 9-35 9-5 8-127

14 3 45 23 1 27 13 15 17 8 5 7 6 8 22 11 12 21 33 34 4 9 7 1 9 8 13A 13 6 2 3 4 5 20 4 8 3 13 12 6 5 18 14 21 23 12 5 7 8 10 18 1 9 14 14 29 21 25 2

PART NO.

112486A1 112486A1 112509A1 112517A1 112865A1 112946A1 113133A2 113133A2 113133A2 113135A2 113248A2 113248A2 113248A2 113248A2 113248A2 113457A1 113561A1 113561A1 113561A1 113561A1 113561A1 113561A1 113561A1 113561A1 113629A1 113787A3 113793A4 113793A4 113793A4 113794A4 113794A4 114295A1 114296A1 114318A1 114882A1 114903A1 114980A1 115507A1 115633A1 115633A1 116339A1 116423A1 116425A1 116426A1 116427A1 116534A1 116760A1 116761A2 116763A1 116764A2 116766A2 116767A1 117844A1 117846A1 117933A1 118318A1 118769A1 118900A1 118901A1 118901A1 119129A1 119171A1 119171A1

PAGE

REF.

6-15 6-61 6-9 6-47 9-97 9-15 8-15 8-129 9-13 8-129 8-89 8-91 8-93 8-95 8-97 9-15 6-3 6-5 6-7 6-9 6-11 6-13 6-15 6-17 9-11 8-79 8-73 8-75 8-81 8-75 8-85 6-13 6-9 9-47 5-3 8-77 9-93 8-3 8-7 8-9 9-13 4-41 6-13 6-13 6-13 9-157 9-109 9-111 9-111 9-111 9-111 9-111 2-15 6-23 6-55 8-79 9-103 9-11 9-11 9-13 9-11 9-109 9-111

10 10 3 4 10 3 34 1 20 2 1 1 1 1 3A 1

25 17 3 3 4 20 9 12A 2 6 8 28 8 17 21 2 12 7 8 7 3 1 2 3 4 5 7 33 6 8 7 24 30 3 6 4 6

PART NO.

PAGE

REF.

119211A1 119241A1 119243A1 119266A1 119267A2 119268A1 119895A3 120032A1 120148A2 120204A1 1202956C1 120303A1 120303A1 120303A1 120303A1 120303A1 120303A1 120303A1 120303A1 120386A1 120388A1 120421A2 120421A2 120943A1 121-119 121-145 121335A1 121412A1 121413A1 121413A1 121413A1 121413A1 121413A1 121413A1 121414A1 121414A1 121416A1 121478A1 121501A1 121519A1 121638A2 121639A2 121658A1 121665A1 121729A1 121730A2 121736A2 121736A2 121736A2 121741A1 121741A1 121778A1 121779A1 121817A1 121856A1 121856A1 121856A1 121856A1 121856A1 121856A1 121856A1 121920A1 122125A1

9-103 6-53 5-19 4-23 4-23 4-23 8-39 4-25 8-79 9-3 4-31 8-11 8-13 8-13 8-17 8-65 8-67 8-69 9-79 5-5 5-5 5-7 5-11 9-79 4-33 7-7 3-7 4-19 4-19 4-21 4-47 8-43 8-63 8-67 4-19 9-105 4-19 8-135 2-3 9-27 8-117 8-117 6-23 9-45 7-9 7-9 8-73 8-75 8-77 8-41 8-117 9-47 9-49 8-3 3-3 9-79 9-85 9-87 9-89 9-91 9-93 9-19 8-3

11 1 4 1 6 7 22 3 13 24 24 10 8 21 8 26 31 14 33 13 14 23 23 14 20 11 7 9 30 1 40 32 37 8 9A 14A 21 3 1 4 20 7 8 4 1 1 1 3 2 5 17 25 2 2 2 13 18 12 27



10-10


PAGE

REF.

122127A1 122140A1 122141A1 122176A1 122178A2 122178A2 122179A1 122179A1 122264A1 122265A1 122268A1 122270A1 122284A1 122330A1 122359A1 122535A1 122536A1 122536A1 122536A1 122553A1 122553A1 122554A1 122579A1 122603A1 122736A1 122740A1 122897A1 122958A1 122974A1 122993A1 122995A1 123097A1 123167A2 123168A1 123206A2 123318A1 123392A1 123405A6 123407A1 123493A1 123538A1 123558A1 123615A2 123726A1 123732A1 123800A1 123803A1 123809A2 123815A1 123842A2 123842A2 123842A2 123842A2 123842A2 123842A2 123842A2 123842A2 123842A2 123842A2 123842A2 123842A2C 123842A2R 123843A2

8-7 8-77 8-77 8-9 8-45 8-47 8-45 8-47 6-7 6-7 6-5 6-5 9-49 8-79 9-3 8-135 5-5 8-9 8-125 9-141 9-143 9-143 9-141 9-79 4-17 4-17 9-49 9-53 9-53 9-53 9-53 4-11 9-49 9-49 9-135 9-51 3-9 8-137 8-137 9-5 4-17 3-9 4-25 8-133 8-133 6-45 6-45 4-11 9-5 6-23 6-27 6-29 6-33 6-35 6-37 6-39 6-41 6-43 6-45 6-49 6-27 6-27 6-23

4 5 5A 11 20 20 18 18 10 9 13 7 10 15 23

Bur 7-3350

18 1 12 4 11 13 24 5 7 6 13 1 19 16 32 23 26 2 29 13 16 17 9 4 12 12 12 13 21 24 31 2 14

15

PART NO.

PAGE

123843A2 123843A2 123843A2 123843A2 123843A2 123843A2 123843A2 123843A2 123843A2 123843A2 123843A2 123843A2 123843A2C 123843A2R 123942A1 123943A1 123980A1 124011A1 124243A1 124462A1 124463A1 124568A2 124646A1 124690A1 124721A1 124727A1 1250594C1 1250594C1 1250594C1 1250594C1 1250594C1 125113A1 125113A1 125688A1 125749A1 126-116 126155A1 126155A1 126177 126371A1 126844A1 126844A1 126844A1 126844A1 126844A1 126844A1 126844A1 126907A1 126918A1 127009A1 127021A2 127073A1 127158A1 127324A1 127367A1 127377A1 127378A3 1280055C2 128265A1 128312A1 128376A1 128401A1 128403A1

6-27 6-31 6-33 6-35 6-37 6-39 6-41 6-43 6-45 6-47 6-49 6-51 6-27 6-27 8-49 8-49 9-141 9-141 9-5 8-135 8-135 8-135 7-13 8-23 9-9 9-141 9-141 9-141 9-143 9-143 9-143 9-35 9-35 9-133 9-133 6-23 8-45 8-47 9-151 9-115 4-23 4-25 4-25 4-25 4-25 4-25 9-125 9-139 9-41 4-25 9-115 9-137 4-43 9-147 9-147 9-95 9-95 8-49 9-147 9-11 6-65 9-25 9-25

REF.

9 27 23 22 8 22 3 5 15 14 15 10 11 3 10 17 12 14 3 6 12 16 16 3 4 13 15 15A 17 18 30 7 6 2 5 8 18 6 6 24 3 8 14 9 19 11 3 1

PART NO.

PAGE

REF.

128406A1 128410A1 128411A1 128412A1 128483A1 128483A1 128483A1 128483A1 128483A1 128483A1 128484A1 128484A1 128485A1 128485A1 128485A1 128485A1 128570A1 128570A1 128580A1 128804A1 128818A1 129-289 129-369 129-667 129015A1 129391A1 129586A1 129698A1 129699A1 129699A1 129735A1 129735A2 129842A2 129842A2 129861A1 129861A1 129864A4 129864A4 129864A4 129864A4 129864A4 129914A1 13-1638 130047A1 130048A1 130049A1 130059A1 130060A2 130245A1 130479A1 130480A1 130876A1 130919A1 130932A1 131-203 131-425 131-431 131-619 131-623 131-623 131-623 131-623 131-623

9-137 9-139 9-139 9-139 9-141 9-141 9-143 9-143 9-143 9-145 9-141 9-143 9-141 9-141 9-143 9-143 6-17 6-63 9-9 9-155 9-11 9-43 5-13 8-125 9-29 8-119 4-25 8-85 8-79 8-85 8-85 8-79 8-73 8-75 8-99 8-101 8-89 8-91 8-93 8-95 8-99 9-5 5-15 3-3 3-3 3-3 8-77 8-77 7-13 9-25 9-25 4-19 8-119 8-119 9-121 9-107 9-157 4-25 4-23 4-25 9-3 9-7 9-25

7 10 11 2 9 16 16 18 25 4 4 9 3 8 2 8 11 9 12 11 17 3 2 1 22 20 27 23

5 6

2 3 3 3 4 14 15 21 5 11 32 4 2 27 16 10 4 17 14 9 6 4 33 15


580 Super L Series 2 Loader Bacl(hoe

10-11


PAGE

131-861 131039A1 131041A1 131042A1 131084A1 131124A1 131127A2 131196A1 13i197A1 131197A1 131586A1 131600A1 131676A1 131691A1 131794A1 131794A1 131795A1 131795A1 131796A1 131796A1 131797A1 131797A1 131973A1 131973A1 131974A1 131975A2 131977A2 132004A2 132004A2 132004A2 132024A1 132025A1 132133A1 132134A1 132212A1 132212A1 132212A1 132212A1 132215A1 132217A1 132218A1 132661A1 132716A1 132842A1 132844A1 132862A1 132866A1 132872A1 132873A1 132929A1 132930A1 132930A1 132930A1 132930A1 132931A1 132931A1 133024A1 133025A1 133041A1 133083A1 . 1331102C2 133421A1 133422A1

9-133 9-137 9-137 9-137 2-3 9-139 9-141 8-119 8-117 8-119 8-3 8-45 7-9 4-17 4-31 4-39 4-31 4-39 4-31 4-39 4-31 4-39 9-133 9-137 9-137 9-99 9-115 8-73 8-75 8-83 9-129 9-129 9-99 9-99 8-25 8-27 8-29 8-33 2-3 2-3 2-3 9-3 9-61 9-61 9-61 9-105 9-105 9-107 9-7 5-5 8-25 8-27 8-29 8-33 3-9 9-3 9-97 9-97 4-19 8-127 9-133 9-107 9-107

Bur 7-3350

REF.

7 • 8 10 11 8 1 1 3 3 10 14 6 19 17 15 14 2 12 9 IB 4A 4 5 17A 8 1 17 17 16 16 12 14 13 5 52 54 53

39 12 38 32 24 24 2 25 2 1 12 4

PART NO.

PAGE

REF.

133604A1 133604A1 133605A1 133605A1 133605A1 133605A1 133615A1 133617A1 133711A1 133713A1 133715A1 133716A1 133989A1 1340287C1 1340287C1 134031901 134034501 134034501 134047801 134049202 134079801 1340969C2 134096902 134096902 134097001 134125A1 134167A1 134197501 134205401 134365803 134370801 134370801 134370801 134370801 134370801 134370801 134370801 134370801 134370801 134377701 134377701 134379102 134393802 134402501 134402601 134423201 134437A1 134437A1 134548803 134601802 134602301 134610101 134610502 134610502 134610502 134610502 134610502 134610502 134610502 134610502 1346105C2 134610502 134610502

8-29 8-33 8-25 8-27 8-29 8-33 9-3 9-5 4-21 4-21 4-21 4-21 9-5 9-125 9-141 4-25 9-119 9-121 8-49 9-137 8-131 8-37 8-143 9-59 8-143 9-137 9-47 8-119 5-3 5-11 8-79 8-81 8-85 8-99 8-101 8-105 8-111 8-113 8-115 8-81 8-85 8-119 9-137 9-105 9-105 9-123 9-55 9-59 4-11 8-137 8-107 8-137 8-79 8-81 8^85 8-99 8-101 8-105 8-107 8-109 8-111 8-113 8-115

26 26 36 30 22 22 2 18 12 13 15 14 13 12 14 31 11 10 13 1 15 22 1 .25 2 • 6 20 17 1 20 23 17 13 17 17 35 13 13 21 - 15 2

18 -•

4 18 3

PART NO.

134610601 134610702 134610702 134610702 134610702 134610802 134610802 134612803 134612903 134617501 134617501 134617501 134617501 134617501 134617501 134617501 134617501 134617501 134618901 134618901 134619001 134619001 134619101 134619201 134619501 134621902 134621902 134621903 • 134621903 134621903 134621903 134621903 134621903 134621903 134622102 134622102 134622102 134622102 134622201 134631202 ,134826401 134844A1 134905801 134905901 134905901 135161A1 135183A1 135183A1 135185A1 135247A1 135248A1 135249A1 135324A1 135512A3 135867A1 135869A1 136-154 136-54 136008A1 136008A1 136036A1 136226A1 136261A1

PAGE

1 '

8-103 8-89 8-91 8-93 8-95 8-73 8-75 8-117 8-117 8-79 8-81 8-85 8-99 8-101 8-105 8-111 8-1-13 8-115 8-19 8-131 8-19 8-131 8-131 8-131 8-131 8-81 8-85 8-79 8-99 8-101 8-105 8-111 8-113 8-115 8-97 8-101 8-105 8-109 8-109 8-119 3-3 9-17 6-17 6-17 6-63 8-127 9-125 9-155 9-125 9-47 9-47 9-47 9-145 9-105 5-11 5-11 9-121 4-43 8-7 8-43 9-125 8-13 9-29

REF.

12 10 19 22 16 12 16 16 34 12 12 2 1 1 1 2 2 13

41 18 3 5 6 • 5 13 2 3 1 16 9 10 2 12 17 26 14 17 52 3 26 ir

lissued February, 1998

10-12



PAGE

REF.

136263A1 136263A1 136267A1 136269A1 136270A1 136271A1 136279A2 136280A1 136436A1 136450A1 136454A1 136494A1 136610A5 13661 OAS 136610A5 136610A5 136610A5 136745A1 136822A1 136824A1 136977A1 136990A1 137012A1 137039A1 137135A1 137219A1 137223A2 137248A1 137283A1 137289A1 137290A1 137315A1 137315A1 137315A1 137343A1 137343A1 137344A1 137344A1 137655A3 137713A1 137731A1 137851A1 137851A1 137851A1 137868A3 137868A3 137869A3 137869A3 138255A1 138467A1 138467A1 138595A1 138616A1 138616A1 139043A1 139180A1 139195A1 139227A1 139230A1 139235A1 139362A1 139362A1 139362A1

9-29 9-33 9-29 9-29 9-31 9-31 9-101 9-101 8-35 4-23 4-23 5-11 8-89 8-91 8-93 8-95 8-101 9-97 9-25 9-25 8-41 6-5 8-41 8-117 9-133 4-47 6-3 8-135 9-9 9-155 9-155 9-87 9-89 9-123 8-45 8-47 8-45 8-47 9-101 8-41 9-117 4-23 9-115 9-147 9-117 9-119 9-117 9-119 9-143 8-13 8-17 9-79 5-15 6-3 8-49 9-13 9-13 8-49 8-49 9-13 9-93 9-99 9-121

8 2 5 6 40 39 3 7 51 14 18 9 3 4 4 4

Bur 7-3350

9 11 13 16 8 14 9 13 13 13 1 6 5

26 19 19 21 21 1 15 20 2 2 25 1A 1 1 1A 15 12 11 14 8 9 8 12 14 1 23 13 7 9 23

PART NO.

PAGE

REF.

139363A1 139486A2 139490A1 139492A1 139494A2 139500A1 139502A1 139768A1 139808A2 139810A2 139834A1 139835A1 139865A1 140-103 140-104 140-106 140-106 140-107 140-107 140-107 140-107 140-107 140-107 140-107 140-107 140-119 140327A1 140428A1 140453A1 140943A1 140944A1 140945A1 140946A1 140947A1 140948A1 140949A1 140951A1 140953A1 140954A1 141232A1 141233A1 141233A1 141234A1 141234A1 141249A1 141324A1 141404A1 141471A1 141472A1 141473A1 141513A1 141801A1 141806A1 141809A1 141811A1 142-103 142-103 142003A1 142007A1 142120A1 142122A1 142124A1 142126A1

9-93 9-93 9-91 9-91 9-83 9-93 9-93 9-135 8-135 8-135 9-91 9-91 9-9 9-133 9-119 4-25 9-25 4-23 4-23 4-23 4-27 9-3 9-7 9-93 9-99 4-25 9-135 9-91 9-59 6-17 6-17 6-17 6-17 6-17 6-17 6-17 6-17 6-17 6-17 9-71 9-71 9-71 9-71 9-71 9-77 9-11 9-97 9-13 9-13 9-15 2-3 8-29 8-29 8-37 8-37 9-117 9-119 7-9 7-9 8-25 8-25 8-27 8-27

9 1 4 3 1 22 20 1 1 2 19 15 8 5 5 13 14 8 11 15 22 3 32 31 19 24 5 18 7 7 7 7 7 7 7 7 7 7 1 3 3 2 2 15 1 3 1 2 18 21 20 11 12 9 7 3 18 22 35 29 21

PART NO.

PAGE

REF.


9-19 9-9 9-11 9-15 9-17 8-71 8-71 8-25 5-3 5-9 9-147 9-147 9-5 9-79 9-79 9-113 6-23 8-21 8-25 8-27 8-29 8-33 5-11 5-11 5-11 9-105 8-25 8-27 8-29 8-33 4-13 9-155 9-153 8-25 8-137 9-49 8-137 8-3 8-7 5-5 8-9 5-5 8-5 8-9 8-27 8-7 8-7 8-19 8-19 8-21 6-19 6-69 6-19 6-69 9-97 9-97 9-99 8-89 8-91 8-93 8-95 8-105 8-107

3 2 12 7 8 4 11 31 6 12 13 7 19 20 10 13 19 12 12 11 11 11 13 16 16 15 15 4 1 10 28 1 9 2 19 3 15 12 6 36 6 28 16 16A 5 12 10

7 7 5 17 15 5 6 6 6



10-13


PAGE

REF.

144324A4 144324A4 144324A4 144453A1 144454A1 144455A1 144456A1 144457A1 144458A1 144459A1 144460A1 14446.1 A1 144462A1 144463A1 144464A1 144465A1 144466A1. 144477A1 144477A1 144477A1 144477A1 144479A1 144479A1 144900A1 144908A1 151-522 1530028C1 1530028C1 1530431 C I 1537663G1 1537664C1 1542563C1 1542829C1. 1542829C1 •1542829C1 1542829C1 1542829C1 1542874C1 1542875C1 1542875C1 1542875C1 1542876C1 1542876C1 1542877C1 1542879C1 1542879C1 1542914C1 1542915C2 1542918C1 1542919C2 1542923C2 1542928C1 1542929C1 1542930C1 1542930C1 1542931 C I 1542931CI 1542996C1 1542997C1 1542998C1 1542998C1 1542998C1 1542999C1

8-93 8-95 8-113

2 2

6-5

1

Bur 7-3350

-

6-5 6-7 6-7 6-9 6-9 6-9 6-17 6-11 . .6-11 6-11 6-11 6-11 6-13 8-7 8-39 8-51 8-53 8-7 8-51 9-127 9-91 4-23 6-29 6-31 4-7 6-7 6-7 8-119 8-89 8-91 8-93 8-95 8-97 8-129 8-127 8-131 8-143 8-133 8-135 8-137 8-139 8-141 8-139 8-139 8-137 8-137 8-141 8-137 8-137 8-139 8-141 8-139 8-141 8-129 '8-129 8-127 8-131 8-143 8-127

1 2 5 7

1 5 2

4 27 4 32 39 30 31 29 24 20 2 2 .5 5 6 7 8 8 8

4 6

11 10 9 9 8 8 8 7 8 9 7 7

PART NO.

PAGE

1542999C1 1542999C1 1543000C1 1543000C1 1543001 C I 1543001 C I 1543256C1 1543260C1 1543267C1 1543267C1 1543275C1 1543329C1 1546500C1 1547924C1 161-115 165-129 168-71 170-104 172599 174-93 175156A1 175160A1 175161A1 175162A1 175163A1 175164A1 175165A1 175599A1 175637A1 175955A1 175959A1 175961A1 175964A2 175965A1 175966A1 175968A1 175974A1 175976A1 175982A1 175984A1 176091A1 176226A1 176226A1 176226A1 176226A1 176311A1 176311A1 176328A1 176437A1 176857A1 176924A1 176925Ar 176926A1 176952A1 176957A1 177164A1 177269A1 177518A1 177634A1 178004A1 178006A1 178850A1 179029A1

8-131 •8-143 8-133 8-135 8-133 8-135 8-129 8-127 8-131 8-143 8-133 8-119 4-3 2-3 4-45 9-119 4-43 9-5 2-39 2-13 9-19 9-19 2-5 2-5 2-5 2-5 2-5 9-93 2-15 6-59 6-61 6-61 6-65 6-65 6-65 6-65 6-67 6-67 6-67 6-67 9-107 8-25 8-27 8-29 8-33 9-3 •

REF.

•.8 6 8 8 7 7

29 9 9 2 17 7 3 . 11 15

1 4 3 5 6 2 1 14 11 19 9 10 8 •12 1 4 14 19 13 13 12 12 10 ' 20 21

9-5

5-7 2-11 4-23 9-109 9-109 9-1099-83 9-83 4-23 4-45 8-135 8-25 9-35 9-35 8-139 9-41

2

12 5 2 • 'i

-1 5 ; 6 10 9 12 34 18 17 14 1

PART NO.

PAGE

179355A1 179683A1 179683A1 179689A1 179956A1 180318A1 180376A1 180402A1 180427A1 180578A1 180593A1 180594A3 1806233C1 1806234C1 1806235C1 1806236C1 1806237C1 1806238C1 1806239C1 1806240C1 1806241C1 1806242C1 1806243C1 1806244C1 1806245C1 1806246C1 1806247C1 1806248C1 1806249C1 1806250C1 1806251 C I 1806252C1 1806253C1 1806254C1 1806255C1 1806256C1 1806257G1 1806258C1 1806259C1 1806260C1 1806261 C I 1806262C1 180801A1 180801A1 1808728C1 1808822C1 181042A1 181042A1 181100A1 181100A1 181100A1 liBIIOOAl 181101A1 181102A1 181103A1 181104A1. 181105A1 181105A1 181107A1 181108A1 181108A1 181109A1 181111A1

11 9-123 8-49 25 7 9-155 6-23 6 9-27 6 8-45 3 9-27 2 9-27 2A 9-77 2 9-77 23 9-105 9-107 3-1910 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 • 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 ' 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19 10 3-19.: 10 3-19 10 3-19 10 3-19 10 3-19 10 7-13 25 9-14717 3-17 10 3-17 17 9-49 22 9-59 8 4 6-29 6-31 4 6-49 35 6-51 5 6-27 2 6-27 12 6-49 20 6-37 23 6-29 12 6-31 12 6-49 19 6-41 19 6-45 26 6-33 5 6-41 13

:

1

REF.



10-14



Bur 7-3350

PAGE

6-43 6-41 6-43 6-47 6-47 6-45 6-41 6-47 6-39 6-41 6-45 6-39 6-43 6-41 6-49 6-49 6-35 6-35 6-27 6-29 6-31 6-33 6-45 6-33 6-49 6-51 6-39 6-41 6-47 6-41 6-39 6-41 6-45 6-47 6-41 6-41 6-41 6-41 6-41 6-41 6-41 6-41 6-45 6-49 9-109 9-111 6-35 6-35 6-35 6-31 6-35 6-45 6-29 6-31 6-39 6-47 6-45 6-39 6-39 6-39 6-39 6-39 6-43

REF.

5 9 1 19 5 31 24 9 7 3 30 12 2 6 5 28 12 5 4 14 15 19 33 9 18 4 2 1 7 4 8 5 29 10 18 17 12 11 14 8 10 23 34 22 6 7 7 16 18 14 11 11 11 4 13 27 11 3 5 10 9 16

PART NO.


PAGE

6-43 6-45 6-43 6-43 6-47 6-27 6-29 6-31 6-47 6-33 6-31 6-31 6-37 6-33 6-49 6-49 6-33 6-33 6-33 6-33 6-27 6-47 6-43 6-43 6-41 6-41 6-29 6-31 6-49 6-35 6-47 6-49 6-49 6-49 6-49 6-49 6-49 6-49 6-49 6-49 6-29 6-29 6-33 6-49 6-49 6-27 6-37 6-47 4-23 4-15 4-19 4-25 4-31 9-99 4-31 9-11 9-141 9-141 9-137 9-33 8-23 8-31 4-25

REF.

4 28 19 3 8 5 6 6 3 1 1 10 21 15 23 24 10 12 14 21 10 11 18 17 22 7 13 13 15 19 15 9 31 25 27 10 29 26 17 30 1 10 3 7 6 3 24 18 1A 6 3 25 13A 1A 21 7A 24 5 5 4 26 40 4

PART NO.


PAGE

REF.

9-27 9-95 9-153 9-101 7-7 7-9 7-11 9-97 9-99 9-137 4-45 9-11 5-3 9-153 9-153 9-153 9-153 9-153 9-153 9-91 8-23 9-61 4-31 4-39 4-31 4-39 4-31 8-31 8-29 8-35 4-39 4-39 8-139 8-139 9-153 9-131 4-11 4-19 9-137 8-35 4-15 4-15 6-57 8-37 8-37 9-27 9-27 9-27 9-97 9-99 9-103 9-109 9-111 9-93 9-93 9-77 2-3 9-19 9-87 9-89 9-17 9-53 3-3

10 10 1 2 1 1 24 2 3 6 27 9 7 6 3 2 5 4 7 14 55 16 18 12 35 29 52 6 3 1 2 8 4 23 12 22 38 3 2 11 18 17 16 11 7 25 3 1

14 32 8A 27 5 7 4 9 4



10-15


PAGE

REF.

185926A1 185975A1 185976A1 185977A1 1.85978A1 185979A1 185980A1 185981A1 185982A1 186351A1 186405A1 186433A1 186607A1 186756A1 186797A1 186977A1 186977A1 186977A1 186989A1 187013A1 187281A1. 187389A1 187438A1 187535A1 187536A1 187582A2 187612A1 187637A1 187639A1187677A1 187714A1 187715A1 187834A1 187836A1 187845A1 188008A2 188009A1 188058A1 188311A2 188411A2 188482A1 188482A1 189103A1 189109A1 189111A1 189111A1 189263A1 189293A1 189294A1 189295A1 189296A1 189297A1 189298A1 189299A1 189404A1 189414A1 189601A1 189602A1 189709A1 189955A1 189957A1 189957A1 19-488

9-79 9-27 9-41 9-37 9-37 9-37 9-37 9-37 9-37 9-103 9-45 "2-3 4-19 4-31 9-133 9-77 9-77 9-77 9-157 4-21 4-45 9-93 9-7 8-11 8-11 9-117 8-59 8-33 8-33 8-59 6-23 6-23 4-31 4-31 8-25 9-79 3-3 8-17 3-3 9-99 9-97 9-99 8-59 3-9 8-57 8-59 8-59 9-33 9-29 9-29 9-29 9-29 9-29 9-29 9-137 8-57 8-57 3-3 8-59 9-45 8-59 8-121 8-71

4 1 10 8 10 14 15 1 2 11A

-

Bur 7-3350

5 28 11 7A 13 20 25 : 16 28 . 7 33 35 14 15 3 25 20 21 10 12 6 7 23 26 29A 18 11 8C 23 7 20 2A

21 10 32 . 30 29 28 31 33 4 2 • 4 29 12 24 1 19

PART NO.

PAGE

190-105 190035A1 190036A1 190155A1 190267A1 190313A1 190426A1 i190429A1 190430A1 190431A1 190432A1 190433A1 190434A1 190435A1 190436A1 190437A1 190438A1 190439A1 190440A1 190441A1 190442A1 190443A1 190444A1 190447A1 190448A1 190449A1 190450A1 190451A1 190452A1 190453A1 190456A1 190457A2 190458A2 190459A1^ 190460A1 190461A1 190463A1 190468A1 190469A1 190471A1 190473A1 190476A2 190477A2 •190492A1 190493A1 190500A1 190502A1 ,190504A1 "190506A1

4-31 9-45 9-45 4-41 9-71 9-49 6-27 6-51 6-51 6-51 6-51 6-27 6-49 6-49 6-49 6-49 6-49 6-49 6-49 6-49 6-49 6-49 6-49 7-3 7-5 7-3 7-3 7-5 6-61 7-3 7-5 6-59 6-59 6-59 7-3 7-3 7-5 6-61 6-61 6-61 7-5 7-5 7-5 7-3 7-3 7-3 7-3 7-3 6-63 6-63 6-63 6-63 6-63 6-63 6-63 -6-63 6-63 6-63 9-141 6-23 9-139 6-13 6-13

190508A1 190509A1 190510A1 190511A1 190512A1 190513A1 190514A1 190515A1 ,190516A1 190599A1 190618A1 19b675A1 190682A1 190684A1

REF.

PART NO.

20 26 28 1 1 27 6 :-. 8 .. 9 10 7 13 37 4 12 11 - 38 14 2 3 32 15 12 7 9 1 14 17 : 9 3 7 8 6 5 2 16 6 4 8 4 4 12 14 20 13 22 7 •7 7 7 7 7 7 7 7 7 ,. 7 7 17 10 9

190967A1 191017A1 191046A1 191047A1 191067A1 191075A1 191076A1 191215A1 191239A1 191532A1 191532A1 191703A1 191704A1 191764A1 191758A1 191796A1 191796A1 192025A1 192152A1 192154A1 192156A1 192196A2 192274A2 192299A1 • 192299A1 192299A1 192300A1 192300A1 192345A1 192352A1 192450A1 192481A1 192559A1 192693A1 192815A1 192895A1 193-1000 193-1000 193-1000 193-1000 • 193-1003 193-1003 193-1003 193117A1 193117A1 193117A1 193117A1 193117A1 193261A1 193261A1 • 193262A1 193262A1 193499A1 193499A1 ' 193499A1 193499A1 193499A1 193707A1 193793A1 193854A1 193913A1 194199A1 . 194513A1

PAGE

REF.

27 9-45 9-47 2 3-5 30 9-79 27 6-61 15 8-45 11 8-49 2 8-45 1 1 9-23 4-21 21 8-43 38 9-143 26 5-7 40 9-143 27 8-21 • 31 5-15 5 6-3 8 8-59 9 27 8-15 8-15 31 8-15 30 4-11 22 9-99 8D 4-21 29 8-43 39 14 9-155 8-49 26 9-155 15 8-19 4 8-19 3 9-155 13 6-59 19 9-77 4 8-41 23 9-11 28 8-123 2 4-11 3 4-11 18 4-19 5 4-19 15 4-47 12 9-11 17 9-103 10 11A 8-25 8-27 11A 10A 8-29 10A 8-33 8-37 10A 8-45 19 8-47 19 21 8-45 8-47 .21 11 8-25 8-27 11 8-29 10 8-33 10 8-37 10 9-131 23 8-27 22 9-9 3 12 9-143 3-3 23 9-147 20


10-16



PAGE

REF.

194520A1 194858A1 195-140 195-2015 195-81013 195-81023 195030A2 195032A1 195447501 195473601 195615A1 195615A1 195785503 195785601 195788701 195802801 195897001 195950901 196050A1 196065A1 196066A1 196087A1 196090A1 196095A1 196096A1 196164A1 196247A1 196252A1 196278A1 196466A1 196466A1 196467201 196496401 196496601 196496801 196496901 196613601 196613801 196614901 196614902 196615301 196616901 196618601 196619101 196655901 196673A2 196675A2 196683501 196699301 196700301 196750601 196753701 196803A1 196813A1 196815A1 196817A1 196819A1 196821A1 196824A1 197136801 197345A1 197346A1 197694301

9-75 9-133 9-25 4-5 9-43 9-119 9-39 9-39 9-141 9-139 9-3 9-5 8-119 8-119 8-119 8-137 9-119 5-3 9-145 6-67 6-67 5-11 6-67 8-77 8-77 8-141 3-3 3-3 8-23 2-31 2-41 9-125 4-7 4-7 4-7 4-7 6-5 6-5 6-5 6-59 6-15 6-13 6-5 6-5 6-15 9-117 9-117 6-35 6-35 6-15 6-45 6-45 2-41 8-13 8-13 8-13 8-13 8-17 8-17 9-119 9-155 9-155 7-9

1 14 8 37 6 9 1 2

Bur 7-3350

3 6 19 44 43 45 19 16 4 6A 21 22 33 2 17 18 14 25 13 10 14 39 19 16 14 4 7 16 17 5 13 9 2 10 11 11 12A 12 3 4 4 23 25 25 24 13 14 13 12 18 16 17 13

PART NO.

PAGE

REF.

197718A1 197739901 197740101 197740201 197745A1 197756402 197793A1 197806801 197814101 197814201 197814301 197814401 197815801 198008403 198008501 198022601 198022701 198029601 198030202 198032102 198033501 198185001 198323301 198333501 198410A1 198493801 198539A1 198656801 198661201 198662801 198672201 198675301 198675401 198690601 198709601 198709701 198712A1 198713A1 198721201 198721902 198729001 198755901 198755901 198976A1 198996001 199054804 199072701 1990728C1 199075602 199075802 199458101 199459601 199459601 199459601 199459601 199459601 199459601 199459601 199460801 199460801 199460801 199460801 199460801

9-47 9-119 9-117 9-117 4-45 9-137 9-105 8-109 8-123 8-123 8-123 8-123 8-123 8-119 8-119 8-119 8-119 8-143 8-119 8-127 8-127 9-107 4-11 9-129 9-39 6-13 9-17 8-81 8-81 8-119 8-109 8-139 8-103 8-141 9-137 9-137 6-33 6-33 9-105 9-105 9-105 4-3 4-9 9-47 9-123 9-107 9-123 9-123 9-141 9-143 8-119 8-85 8-99 8-101 8-105 8-109 8-113 8-115 8-79 8-81 8-85 8-99 8-101

33 19 21 21A 11 1A 19 8 5 6 7 12 8 35 33 11 30 4 3 29 5 1 13 7 34 8 17 14 16 16 15 11 4

1 1 12 9 17 19 2 20 28 7 8 8 8 8A 8 8 3 3 3 3 3

PART NO.

199460801 199460801 199460801 199460801 199460801 199467701 199513701 1995137010 199513701R 199720A1 199720A1 199721A1 199721A1 199722A1 199723A1 199953A2 199969301 199975502 199975502 20-21032 20-21232 20-21232 20-21232 205-129 205-129 211-1006 211-1007 211-1009 211-1010 211-1311 213-123 213-123 213-125 213-126 213-126 213-126 213-126 214-1404 214-1404 214-1406 214-1410 214-14104 214-1416 214-1420 214-1432 214-1440 214-1456 214-1464 214-1464 214-1464 214-1464 214-1464 214-1472 214-1472 214-1472 214-1488 214-1704 214-1704 214-1706 214-1708 214-31104 214-3132 214-3132

PAGE

REF.

8-103 8-105 8-109 8-113 8-115 8-119 6-23 6-23 6-23 8-21 8-133 8-21 8-133 8-133 8-133 8-135 9-105 9-143 9-145 9-19 9-15 9-17 9-19 9-115 9-147 5-11 8-119 8-81 5-11 4-3 3-7 3-9 9-9 9-7 9-29 9-33 9-37 3-15 9-137 9-79 9-139 8-25 2-23 8-9 2-3 2-3 2-7 2-7 2-9 8-15 8-19 8-37 8-11 8-31 8-35 8-23 3-3 7-9 7-9 3-3

3 3 3 3 3

13 4 5 4 9 11 8 14 11 20 15 14 17 7 34 22 6 6 2 19 18 19 33 13 24 17 19 9 15 4 40 21 27 21 34 47 22 8 10 11 7

8-59 8-33 8-35

16 37 39

21 21 21 38 1 37 1 2 2 2 6



10-17

NUMERICAL INDEX PART NO. 214-3132 214-3156 214-3188 214-3240 217-1102 217-281 217-347 217-372 217-380 217-436 217-466 217-92 218-1023 218-1237 218-1251 218-1256 218-1256 218-1256 218-335 218-335 218-335 218-435 218-435 218-435 218-459. 218-5053 218-5053 . 218-5057 218-5057 218-5057 218-5057 218-5057 218-5058 218-5059 218-5062 218-5062 218-5062 218-5062 218-5062 218-5062 218-5062 218-5062 218-5063 218-50.64 218-5064 218-5064 218-5064 218-5064 218-5064 218-5064 218-5064 218-5064 218-5069 218-5069 218-5069 218-5069 218-5077 218-5086 218-5105 218-5105 218-5106 218-5106 218-5106

Bur 7-3350 -

PAGE REF. 8-55 8-55 8-21 2-23 9-79 3-15 9-79 3-3 9-79 9-79 2-35 2-3 6-31 8-19 8-19 8-45 8-47 8-55 8-39 8-53 8-55 8-11 8-15 8-17 6-25 5-5 7-9 5-7 6-57 8-39 8-41 8-65 8-41 5-5 8-7 8:7 8-13 8-15 8-17 8-37 8-53 8-67 8-7 8-25 8-27 8-27 8-29 8-29 8-33 8-35 8-37 8-43 8-5 8-7 8-9 8-51 8-3 8-9 6-57 8-65 8-21 8-21 8-23

19 16 28 3 22 9 16 24 21 5 3 .20 • 9 10 11 15 . 15 22 25 43 23 22 41 20 38 7• 19 35 3 7 8 5 12 10 7A 12 2 . 28 2 24 49 42 1 8 8 26 8 31 8 45 8 47 34 14 7 20 17 20 1 3 8 20 11

PART NO.

PAGE REF.

218-5106 218-5107 218-5107 218-5107 218-5107 218-5107 218-5108 218-5108 218-5108 218-5108 218-5117 218-5118 218-5119 218-5119 218-5123 218-5128 218-5135 218-5136 218-5136 218-5137 218-5137 218-5137 218-5137 218-5137 218-5138 218-5145 218-5157 218-5157 218-5157 218-5157 . 218-5158 218-5158 218-5174 218-5185 218-5207 218-5207 218-5210 218-5211 218-5211 218-5211 218-5213 218-5220 218-5220 218-5220 218-5220 218-5241 218-5243 218-5245 218-5245 218-5245 218-5280 218-5280 218-5283 218-5351 218-5351 218-5359 218-5382 218-5490 218-5490 218-5490 218-5576 218-5576 218-5576

8-23 24 8-11 16 8-15 32 8-19 . 18 8-37 . 20 8-41 27 24 8-25 8-27 34 8-51 9 11 8-51 8-61 3 8-59 7 8-23 8 8-23 19 8-25 29 8-41 21 6-57 24 5-7 27 5-15 12 6-21 11 8-3 6 8-9 15 8-19 16 17 8-51 27 8-51 8-61 2 14 8-89 8-91 15 8-93 15 8-95 15 8-41 32 8-117 5 8-39 5 8-51 14 8-73 6 8-75 7 24 8-103 3-3 6 8-77 3 12 9-79 8-97 6 8-13 18 8-61 15 8-63 38 8-65 7 8-11 2 8-39 20 37 8-5 4 8-9 8-9 7A 5-5 ,19 6-3 5 8-59 13 6-3 4 8-21 35 8-59 18 8-59 23 24 8-51 8-61 16 • 8-67 .38 4 5-5, 1 8-39 8-43 42

PART NO.

PAGE REF.

218-5577 218-5600 218-587 218-676 218-736 218-752 218-754 218-756 218-756 218-776 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-1 219-10 219-10 219-10 219-10 219-55 219-55 219-55 219-55 219-55 219-55 219-55 219-55 219-89 219-89 220169A1 220276A1 220413A1 221-1382 221-190 221-87 221-89 221143A1 221146A1 221158A1 221162A1 221168A1 221330A1 221418A1 221425R1 221553A1 221733A1

8-65 10 8-63 24 8-3 20 21 8-55. 8-7 6 3-17 29 24 8-39 8-41 29 8-51 25 8-17 17 5-15 9 6-3 6 19 8-127 8-131 21 8-133 19 8-135 20 8-137 25 22 8-139 8-141 22 32 9-11 9-13 5 9-13 23 9-19 9 9-31 41 9-41 14 9-47 28 9-49 3 17 9-49 9-55 24 9-59 3 9-61 35 9-61 41 6-19 5 6-19,. 8 6-69 5 6-69 8 8-11 19 8-129 19 8-131 22 8-135 21 9-11 10 9-47 30 9-53 23 9-77 9 21 5-15 5-15 , 30 8-13 5 8-59 28 9-77 7 9-139 23 9-139 23A 3-15 7 21 9-139 8-15 44 8-15 45 8-11 28 24 8-11 8-121 15 8-59 27 4-45 1 4-7 26 8-39 16 8-13 19


10-18



PAGE REF.

PART NO.

PAGE REF.

222-41 222-615 222-650 222-660 222-993 222421A1 222422A1 222688A1 223-26 223199A1 223722A1 223944A1 224423A1 224788A2 225-14105 225-14106 225-14110 225-14210 225-14210 225-14210 225033A1 225059A1 225326A1 225328A1 225330A1 225332A1 225713A1 225714A1 226376A1 226378A1 226456A1 226560A1 226580A1 226582A1 226584A1 227178A2 227293A1 227420A1 228120A1 228120A1 228133A1 228689A1 228959A1 229398A2 229676A1 229684A1 230-4214 230-4215 230-4215 230-4216 230-4216 230-4217 230-42409 230072A1 230073A1 230078A2 230513A1 230588A1 230589A1 230590A1 230857A1 230973A1 231-14109

3-15 2-13 2-13 2-13 2-23 2-9 2-9 6-59 8-57 9-95 7-13 2-7 5-5 8-41 9-5 4-27 4-23 3-7 3-9 8-49 2-11 9-121 8-17 8-17 8-11 8-11 9-139 9-139 9-127 2-9 9-81 9-105 9-127 9-127 9-127 9-115 2-11 9-115 2-7 2-9 2-3 9-121 8-9 9-93 9-85 8-95 9-121 9-119 9-121 9-45 9-45 9-121 9-123 8-61 8-61 8-61 9-75 9-121 9-121 9-121 9-79 7-7 9-83

231-14109 231-14109 231-14109 231-1444 231-1444 231-1444 231-1444 231-1444 231-1445 231-1446 231-1446 231-1446 231-2446 231-4115 231-4247 231-5144 231-5145 231-5344 231397A1 231520A2 231656A1 231982A1 231984A1 232-4617 232-4617 232366A1 232447A1 232875A1 232929A1 232931A1 232934A1 232936A1 232939A1 232941A1 232945A1 232947A1 232948A1 233262A1 233272A1 233283A1 233284A1 233522A1 233523A1 233724A1 233749A1 233970A1 233971A1 233972A1 234223A1 234277A1C 234277A2 234277A2R 234412A1 234412A1 234499A1 234622A1 234623A1 234719A1 234888A1 234892A1 234913A1 234923A1 234923A1

9-93 9-99 9-117 4-33 4-33 4-45 9-105 9-149 4-33 8-59 9-3 9-5 9-37 9-149 9-45 4-35 9-117 9-123 6-15 4-17 9-79 8-11 8-11 9-103 9-103 2-3 8-13 9-27 8-11 8-11 8-15 8-15 8-11 8-11 8-17 8-17 9-143 9-93 2-3 6-47 6-45 9-91 9-91 9-95 9-89 6-21 6-21 6-21 9-109 2-39 2-39 2-39 8-63 8-123 6-21 7-7 7-7 6-21 3-3 3-3 9-95 9-91 9-93

Bur 7-3350

10 4 5 16 6 7 20 11 16 29 8 9 2 5 20 17 13 20 29 5 27 4 5 4 6 18 31 5 36 21 20 19 23 3 18 1 27 9 24 1 13 16 12 11 23 30 21 16 19 20 17 5 13 12A 12 1A 26 4

15 20 14 6 11 4 12 16 6 18 28 18 9 21 6 23 8 8 6 7 5 19 26 16 4 15 29 32 46 47 30 31 19 21 19 25 4 1 32 2 1 15 15 16 13 9

23 17 34 33 14 19 14 1 35 35

PART NO. 235002A1 235038A1 235040A1 235916A1 235917A2 235921A1 236231A1 236300A1 236521A1 237-6002 237-6004 237-6004 237-6004 237-6004 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6006 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6008 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010

PAGE REF. 8-63 2-3 2-3 8-141 8-141 8-141 8-9 2-39 4-17 8-119 5-5 7-9 8-73 8-75 5-5 5-7 6-3 6-3 6-57 6-57 6-57 8-21 8-39 8-39 8-41 8-41 8-59 8-65 8-65 8-125 8-137 9-79 5-5 5-5 5-7 5-15 6-57 8-21 8-21 8-23 8-23 8-41 8-41 8-59 8-61 8-61 8-63 8-83 8-103 3-3 5-5 6-21 8-3 8-7 8-7 8-9 8-9 8-11 8-11 8-13 8-15 8-15 8-17

26 35 34 1 2 4 14 8A 7 8 19A 7 8 3 36 4A 5A 2 4 25 36 8 21 9 31 14 4 6 4 20 17 11 20 28 13 12 9 21 12 25 13 22 19 2A 3A 24A 3 25 6A 5 12 7 7B 13 10 16 3 17 3 29 33 3



10-19


PAGE REF.

237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 .237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6010 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-:6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012 237-6012' 237-6012

8-19 8-19 8-25 8-37 8-37 8-39 8-39 8-41 8-43 8-51 8-53 8-57 8-67 8-77 8-79 8-85 8-89 8-91 8-93 8-95 8-97 8-101 8-105 8-109 8-119 9-79 8-7 8-23 8-23 8-25 8-25 8-27 8-27 8-27 8-29 8-29 8-31 8-33 8-33 ,8-35 8-37 8-41 8-43 8-45 8-47 8-51 8-51 8-51 8-51 8-59 8-77 8-81 8-85 8-87 8-99 8-101 8-103 8-103 8-107 8-107 8-111 8-113 8-115

Bur 7-3350

17 19 30 21 25 2 23 28 43 18 50 3 43 4 26 22 15 16 , 16 16 10 12 12 12 36 13 2 9 20 9 25 9 27 35 : 9 32 36 9 35 46 9 33 48 17 17 9A 12 15 28 11 14 19 13 13 28 32 11 17 32 45 32 17 28

PART NO. 237-6012 237-6012 237-6014 237-6016 237-6016 237-6016 237-6016 237-6016 237-6016 237-6016 237-6016 237-6016 237-6016 237-6016 237-6020 237021A1 237022A1 237023A1 237024A1 237025A1 237026A1 237948A1 238-5005 238-5011 238-5012 238-5013 238-5013 238-5014 238-5040 238-5118 238-5120 238-5127 238-5139 238-5152 .238-5152 238-5212 238-5225 238-5227 238-5228 238-5230 238-5230 238-5231 238-5231 238-5231 238-5233 238-5235 238-5239 238-5241 238-5242 238-5247 238-5247 238-5270 238-5341 238-5341 238-6011 238-6012 238-6012 238-6015 238-6015 238-6015 238-6016 238-6016 238-6016

PAGE REF. 8-117 8-121 8-97 8-3 8-5 8-5 8-7 8-9 8-9 8-51 8-51 8-59 8-59 8-65 8-9 7-3 7-3 7-3 7-3 7-3 7-3 6-25 4-43 8-125 5-11 2-23 6-57 6-57 5-11 8-97 8-79 8-79 5-15 6-17 6-63 2-45 5-11 5-3 8-3 5-13 8-125 8-129 8-131 8-143 8-127 8-141 8-135 8-133 8-135 8-137 8-139 6-59 2-1.7 2-51 8-119 8-77 8-119 8-109 8-119 8-119 8-79 8-81 8-85

6 13 7 18 35 38 •15 5 8 21 23 . 8 24 11 21 1 2 3 16 21 11 39 8 5 23 15 13 14 = 18 5 14 12 33 10 11 7 28 3 10 10 9 9 10 8 9 11 9 9 23 13 • 11 2 3 7 20 10 42 16 21 27 21 24 18

PART NO. 238-6016 238-6016 238-6016 238-6016 238-6016 238-6016 238-6018 238-6018 238-6018 238-6018 . 238-6018 238-6018 238-6018 238-6018 238-6018 238-6018 238-6018 238-6018 238-6018 238-6018 238-6018 238-6019 238-6112 238-6117 238-6119 238-6119 238-6119 238-6119 238-6119 238-6119 238-6121 238-6121 238-6121 238-6121 238-6121 238-6127 238-6127 238-6127 238-6127 238-6127 238-6127 238-8217 238048A2 239306A1 239606A1 239739A1 239739A1 239880A1 239881A1 240693A2 240703A2 240706A2 240709A4 240711A4 241088A3 241088A3 241088A3 241088A3 241088A3 241957A1 242369A1 242459A1 242561A1

PAGE REF. 8-99 8-101 8-105 8-111 8-113 8-115 8-77 8-81 8-85 8-87 8-99 8-101 8-103 8-103 8-103 8-105 8-107 8-111 8-113 8-115 8-121 8-103 8-117 8-117 8-73 8-75 8-89 8-91 8-93 8-95 6-13 6-29 6-31 6-59 6-67 8-73 8-75 8-89 8-91 8-93 8-95 6-47 '9-21 9-5 6-31 2-3 2-5 9-153 9-153 8-61 8-61 8-61 8-61 8-61 8-89 8-91 8-93 8-95 8-109 6-45 9-11 8-55 9-57

14 18 18 36 14 14 15 18 ' 12 3 18 22 12 15 18 22 35 22 18 18 3 20 8 7 8 9 9 10 10 10 22A 8A 8A 1A 7A 9 10 8 9 9 9 22 1 14 1A 1 22 23 7 14 13 11 12 6 7 7 7 •20 21 9 42


10-20



PAGE REF.

PART NO.

PAGE REF.

PART NO.

PAGE REF.

242562A1 242724A1 243084A1 243122A1 243135A1 243136A1 243137A1 243138A1 243139A2 243141A2 243142A2 243143A2 243145A3 243145A3 243145A3 243145A3 243145A3 243291A1 243338A1 243339A1 243603A1 243679A1 243790A1 243805A2 243893A1 244286A1 244287A1 244441A1 245011A1 245258A1 245287A1 245450A1 245450A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245466A1 245592A1 245706C1 245891A2 246060A1 246063A1 246064A1 246151A1 246158A1 246228A1 246767A1 247550A1 247570A1 247743A1 247744A1

9-57 9-143 9-47 9-95 8-89 8-89 8-93 8-93 8-91 8-91 8-95 8-95 8-89 8-91 8-93 8-95 8-109 8-55 8-43 8-39 9-135 8-55 8-7 6-21 7-3 9-93 9-93 9-91 9-89 9-125 3-9 9-87 9-89 9-63 9-63 9-65 9-65 9-65 9-65 9-67 9-67 9-67 9-67 9-69 9-69 9-71 9-71 9-71 9-71 9-39 9-125 4-25 9-143 9-89 9-89 8-55 8-55 9-93 6-33 6-67 7-9 2-9 6-33


6-33 6-33 6-33 6-67 7-3 8-53 8-53 9-47 8-15 9-13 9-19 4-15 8-53 8-55 8-55 8-55 9-111 9-25 9-143 8-53 9-93 8-89 8-91 8-93 8-95 8-103 6-27 2-13 8-55 3-9 9-93 9-117 9-117 8-23 9-93 8-63 9-157 8-29 8-55 8-63 9-157 9-3 9-7 8-51 7-5 7-5 7-5 7-5 7-5 3-9 6-35 6-37 6-41 6-43 4-13 4-15 9-93 9-93 8-97 2-5 9-43 8-3 8-3

257954A1 258313A1 258616A1 258616A1 25863R1 25863R1 259044A1 259054A1 259071A1 259410A1 25974R1 25974R1 259777A3 25987R1 260-14512 260-16524 261-14310 261-14310 265-16512 273-10510 273-10510 273-5048 275454A1 275455A1 275456A1 275457A1 275464A1 275488A2 275547A1 275547A1 275677A1 275820A3 275967A1 276-2446 276-2446 276-2446 276-2446 276-2446 276-2446 276-2446 276-2446 276-2446 276-2456 276-24916 276070A1 276743A1 276746A1 276962A1 277016A1 277184A2 277187A1 277320A1 277377R1 277502A1 277546A1 277664A1 278183A1 278328A1 278534A1 278665A4 278735A1 278735A1 278735A1

8-71 9-103 9-3 9-7 8-129 8-143 8-3 9-105 9-103 9-43 8-127 8-131 8-65 8-139 9-147 9-119 4-37 4-37 9-117 4-33 4-33 4-35 3-9 3-9 3-9 3-9 2-7 8-67 9-105 9-107 9-43 9-43 2-11 8-127 8-129 8-131 8-133 8-135 8-137 8-139 8-141 8-143 8-123 2-13 9-43 7-9 7-9 8-65 4-11 9-25 9-25 8-65 2-9 9-87 9-145 9-87 3-9 4-17 6-27 4-19 8-97 8-101 8-105

Bur 7-3350

40 7 19 9

6A 7A 7A 7A 20 44 3 8 14 7 6 23 21 36 1 8 14 3 4 6 9 6 6 9 9 6 6 9 9 6 9 6 6 9 9

1 14 5 6 17 15 36 20 13 18 8 2

13 18 24 41 40 1 35 7 26 10 38 2 1 4 8 2A 21 37 26 4 5 5 5 1 18 5 4 27 15 23 30 33 19 30 14A 34 21

30 13 14 17 5 18 5

16 11 28 29 3 2 18 11

2

17 16 1 2A 16 17 19 1 20 30 14 4 11 19 3 9 3 21 25 22 29 10 36 1 1 3 1 1 11 11 12 11 11 15 13 13 10 3 8 12 16 17 12 30 16 4A 2 2 1 7 4 28 8 8 26A 12 14 14



10-21

NUMERICAL INDEX PART NO. 278735A1 279169A1 279169A1 279169A1 279169A1 279169A1 279169A1 279169A1 279169A1 279261A1 279520A1 28-1664 28-2048 28-2048 28-2052 280-16516 280-16516 280164A1 280336A1 280436A1 280450A1 280452A1 280457A1 280681A1 280886A1 280995A1: 280996A1 281-14716 281-18712 281-18712 281-1878 281-4556 • 281-4556 •281-54512 281-5451 £ 281-54512 281-54712 281-54712 281001A1 281009A1 281068A1 281069A1 281185A1 • 281819A4 281952A1 281960A1 282-16512 282-16512 282013A3 282013A3 282014A2 282015A3 282016A3 282017A2 282018A2 282033A1 282038A1 282242A1 282428A1 282428A1 282496A1 282497A1 282842A1

Bur 7-3350

PAGE REF.

PART NO.

PAGE REF.

14 1

282845A1 282845A1 282931A1 283001A1 283226A1 283325A3 283332A1 283417A1 283462A1 283466A1 283579A1 283779A1 283781A1 284041 A3 284058A1 284154A1 284223A1 284431A1 284452A2 284479A1 284479A1 284482A3 284549A1 284627A1 284627A1 284641A1 284712A1 284712A1 284713A1 284713A1 284723A1 286-56520 286-56520 286-56520 29-1010 29-1012 291010A1 291129A1 291288A1 291288A1 291609A1 292207A1 292208A1 292210A1 292212A1 292213A1 292214A1 292262A1 292263A1 292264A1 292268A1 292385A1 292408A1 292436A1 292514A1 292528A1 292654A1 292654A1 292654A1 292740A1 292785A1 292890A1 292891A1

9-115 9-147 3-9 4-29 9-43 9-79 9-43 8-83 7-5 7.5 6-57 4-21 4-21 3-3 4-47 9-127 9-81 3-3 3-3 4-47 9-155 9-155 4-45 4-47 9-155 6-23 6-25 6-69 6-3 6-19 6-23 9-113 9-125 9-147 9-19 9-19 4-45 9-119 6-21 8-9 9-115 6-61 6-61 6-65 6-65 6-65 6-65 9-103 9-103 9-115 6-61 9-47 9-127 8-65 6-25 8-65 4-25 4-45 9-133 2-9 9-93 6-61 6-67

8-109 6-55 6-59 6-61 - 6-63 6-65 6-67 7-3 7-5 7-13 4-17 8-135 8-133 8-137 8-141 6-23 9-95 9-81 9-119 7-5 7-5 7-5 7-5 7-13 7-13 9-113 9-113 9-25 9-25 9-121 9-25 4-19 4-29 9-123 9-125 9-133 9-135 9-149 9-147 9-115 9-119 9-119 9-57 3-3 7-5 7-5 9-137 9-147 4-19 4-21 4-17 4-11 4-11 4-31 4-31 6-3 6-3 3-9 5-5 8-41 8-3 8-3 8-53

18 17 23 20 8 12 40 25 3 20 21 22 9 16 1 1 17 • 7 17 6 16 7 5 5 ^ 13 7 4 1 1 4 3 1A 23 23 7 1 1 . 1 1 1A 1 1A 19 18 1. 2 30 4 2 44

.

16 28 3 9 10 1 18A 5 6 19 9 26 27 1 3 16 38 10 20 2 19 4 12 4 18 29. : 35 11 30 11 4 21 14 5 13 24 1 13 5 12 13 3 4 1 6

25 29 13 13 42 9

10 11 17 •5

PART NO. 292893A1 292894A1 292896A1 292898A1 292899A1 292900A1 292901A1 292902A1 292904A1 292904A1 292962A1 292969A2 292969A2 293021A1 293022A1 293037A1 293037A1 293262A1 293269A1 293571A1 • 293571A1 293636A1 293924A1 293925A1 293926A1 293927A1 293928A1 294189A1 294192A1 294198A1 294198A1 294198A1 294666A1 294666A1 294792A1 295032A1 295108A1 295109A1 295110A1 295111A1 295112A1 295113A1 295114A1 295172A1 295378A1 295580A1 295597A1 > 296171A1 296367A1 296367A1 296508A2. 296508A2 296508A2 296508A2 297255A1 297615A1 297635A1 297836A1 297837A1 297913A1 297914A1 297915A1 297977A2

PAGE REF. 6-67 6-67 6-67 6-67 6-67 6-67 6-67 6-65 9-3 9-7 6-21 8-69 9-23 9-103 9-103 8-63 8-65 9-3 8-51 2-7 2-9 9-47 8-71 8-71 8-71 8-71 8-71 6-63 6-61 8-91 8-95 8-115 9-115 9-147 4-25 7-3 6-59 6-59 6-63 7-3 7-3 7-3 6-59 8-9 4-25 6-67 9-127 7-9 9-115 9-147 4-19 4-47 8-63 8-67 6-57 9-5 8-45 .9-91 9-91 9-115 9-115 9-115 8-61

10 11 23 12 28 27 29 7 1 42 5 4 2

39 8 1A 26 2 34 6A 6 22 22A

2 1A 14 26 7A 8 11 12 6 18 23 24 4 22 7 18 14 9 15 27 35 5 27 35 10 1 8 38 37 29 30 28 1


10-22


PAGE REF.

PART NO.

PAGE REF.

PART NO.

PAGE REF.


9-3 9-7 6-41 4-45 6-25 9-95 3-3 4-47 8-51 9-115 6-49 9-25 9-155 9-77 9-49 4-47 9-115 4-45 9-133 8-47 8-51 9-27 9-59 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-105 9-107 8-53 9-107 8-51 8-51 8-51 8-53 8-53 8-41 8-69 8-65 8-65 9-153 8-47 8-47 8-47

301803R1 302097A1 302246A1 302246A1 302246A1 302246A1 302246A1 302246A1 302246A1 302247A1 302326A1 302358A1 302358A1 302472A1 302474A1 302501A1 302641A1 302803A1 302803A1 302803A1 302803A1 302820A1 302821A1 302846A1 302964A1 302964A1 302964A1 302965A1 302965A1 302966A1 302966A1 302966A1 303022A1 303105A1 303106A1 303108A1 303109A1 303804A1 303806A1 304019A1 304020A1 304390A1 304424A1 304525A1 304527A1 304528A1 304530A1 304572A1 304574A1 304612A1 304890A1 304940A1 305067A1 305152A1 305578A1 305690A1 305818A1 305821A1 305822A1 30634 30634 307243A1 307277A1

9-139 8-51 8-79 8-99 8-101 8-105 8-111 8-113 8-115 8-79 8-79 3-3 9-79 8-51 8-43 8-47 8-51 4-19 4-47 8-63 8-67 8-69 8-69 3-9 8-73 8-75 8-79 8-73 9-3 8-17 8-75 9-7 9-99 9-115 9-115 9-115 9-115 8-69 8-69 6-57 6-57 9-99 8-67 9-145 9-145 9-145 9-145 8-69 8-69 8-67 8-67 9-157 3-7 6-65 9-127 9-89 9-127 9-143 9-143 8-131 8-131 9-147 8-69

307348A1 307348A1 3078897R1 3079134R1 3125705R1 321-1707 321-1707 321-1708 321-1708 321-229 321-230 321-3596 321-4311 321-4481 321-4614 321-6046 321-6376 321-6413 321-6671 321-6672 321-6714 321-6774 321-6872 321-7030 321-7040 326-852 340-12520 345-133 345-133 345-133 345-44 353-225 353-401 353-402 353-405 353-406 353-406 353-406 353-408 353-410 353-411 353-415 353-417 353-422 353-429 376852R91 38-1812 383619R1 396-41028 396-41028 396-41028 396-41028 409-768 409-768 41-1616 413-1228 413-412 413-416 413-420 413-432 413-432 413-432 413-48

3-5 9-155 4-7 4-7 4-43 9-19 9-153 9-19 9-153 9-157 9-157 9-153 9-151 9-153 9-157 9-157 9-157 9-153 9-153 9-157 9-153 9-157 9-153 9-157 9-153 8-71 9-105 9-3 9-7 9-147 6-21 2-45 4-25 9-93 9-147 4-25 9-139 9-147 9-25 9-115 9-25 9-115 9-147 9-95 4-25 8-57 8-119 4-13 9-3 9-3 9-7 9-35 4-31 9-61 2-39 9-45 9-149 9-131 9-121 4-33 4-33 4-35 9-119

Bur 7-3350

20 10 37 2 10 8 1 26 16 18 20 1 18 14 27 5 9 2 2B 26

51 10 16 19 42 48 11 3 21 22 1A 4 3 2

20 22 18 11 15 15 33 11 11 24 7 3 3 29 49 1 6 36 7 37 34 5 9 15 2 2

28 1 40 8B 31 34 32 33 19 21 5 21 8A 40 28 18 29 12 1 2 44 41 5 1 2 30 3 24 24 1 3 14 31 17

39 11A 6 10 24 17 23 16 1 3 18 5 13 18 6 2 14 15 4 12 22 19 8 20 15

12 33 34 3 16 26 23 19 11 5 10 5 7 32 10 31 5 16 31 31 23 4 48 8 18 11 14 14 5A 10A 5 20



10-23


PAGE REF.

PART NO.

PAGE REF.

PART NO.

413-516 413-516 413-536 413-6152 413-624 413-624 413-624 413-624 413-624 413-624 413-624 413-624 413-628 413-632 413-632 413-632 413-632 413-648 413-728 414-412 414-724 414-728 425-1012 425-104 425-105425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-106 425-108 425-1110 425-1120 425-115 425-116 425-116 425-116 425-116 425-116 425-116 425-116 425-118 425-118 425-118 425-118 425-148 425-1510 425-1514 425-154 425-155 425-155 425-155;: 425-155

9-97 9-149 4-33 9-121 8-21 8-23 8-25 8-27 8-29 8-33 8-37 9-37 9-3 5-15 9-5 9-5 9-45 8-59 8-3 9-129 9-103 9-103 9-45 9-131 7-7 4-19 4-21 5-13 5-15 7-13 8-73 8-75 8-89 8-91 8-93 8-95 9-3 9-37 9-127 9-147 4-33 9-35 8-3 9-9 2-35 2-35 9-3 9-5 - 9-7 9-31 9-37 5-15 9-29 9-33 9-35 4-29 8-77 5-13 3-9 2-27 8-87 8-99 8-101

425-155 425-155 425-155 425-155 425-155 425-156 425-156 425-156 425-156 425-156 425-156 425-156 425-157 425-1918 425-285 427-3058 427-3058 427-6088 427-6088 427-6088 427-6088 428-510 429-1010 429-1012 429-1012 432-1232 432-48 432-48 432-48 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-612 432-828 432-828 432-828 435-51652 438-12040 439-5436 440-10616 440-10616 440-1066 440-1088 440-11010 440-11012 442-11016' 443-13112 452698C1 458-412 458-412 459-11014 461-33148

8-107 8-107 8-111 8-115 8-121 7-7 7-13 9-29 9-31 9-33 9-41 9-43 9-131 5-17 9-97 3-7 3-9 9-11 9-29 9-33 9-41 6-23 8-71 9-15 9-17 5-17 3-7 3-7 3-9 7-7 7-13 7-13 9-3 9-7 9-9 9-11 9-29 9-31 9-31 9-33 9-37 9-41 9-41 9-43 ,9-3 9-5 9-35 9-59 7-7 9-5 4-47 9-11 9-79 9-133 9-83 9-93 9-123 9-117 4-5 9-123 9-125 6-23 9-135

465004R91 470-10620 473321 C I 484-43116 484-43116 484-43116 484-43116 484-43116 484-43116 484-43116 484-43120 484-6316 490-11010 490-1106 , 490-1108 490-1108 492-11025 492-11025 492-11025 492-11025 492-11031 492-11038 492-11038 492-11044 492-11050 492-11050 493-11026 493-11039 493-11052 493-21020 493-21020 493-21033 493-41020 495-11022 495-11028 495-11028 495-11028 495-11028 495-11034 495-11041 495-11041 495-11041 495-11041 495-11041 495-11041 495-11041 495-11053 495-11053 495-11053 495-11081 495-11094 495-11106 495-21031 495-21038 495-21038 495-21038 495-21038 495-21044 495-21044 495-21044 495-21044 495-21056 495-21056

Bur 7-3350

.

6 7 14A 2 5 5 5 5 5 .5 5 12 19 22 10 27 22 4 14 18 22 14 19 16 21 13 8 5 24 27 13 14 13 14 .14 14 21 13 18 19 6B 16 22 6 24 28 22 26 38 36 .5 27 10 3 7 4 8 17 . 31 3 12 27 31

31 44 31 27 12 5 17 27 47 9 9 15 3 7 11 15 18 33 25 7 7 22 20 5 6 6 10 16 19 8 3 18 27 37 5 34 26 38 • 49 8 4 ' 8 12 20 13 24 20 •4 24 6 •10 18 IB 12 2 12 14 22 29 6 16 4 3

PAGE REF.

.

9-3 9-103 9-125 8-87 8-99 8-101 8-107 8-111 8-115 8-121 8-107 6-23 3-3 4-19 4-19 4-19 3-9 9-119 9-129 9-131 9-97 5-15 9-127 8-3 4-33 5-15 4-43 4-13 4-29 4-11 8-125 4-11 6-23 8-119 4-45 9-3 9-5 9-151 2-13 4-13 4-15 4-21 7-13 8-59 9-7 9-147 . 6-23 9-11 9-43 9-35 5-15 9-91 4-43 7-13 9-97 9-99 9-121 9-5 9-45 9-79 9-131 4-31 6-3

14A 8 18 11 26 30 30 30 26 11 43 3 27 4A 4 14 30 21 19 15 7 23 17 15 6A 26 2 12 3 9 3 7 5 24 3 8 17 2 11 9 8 23 26 5 34A 18 10 35 9 10 37 33 3 4 8 18 6A 11 29 8 22 13 15


10-24



PAGE REF.

PART NO.

PAGE REF.

PART NO.

PAGE REF.

495-21056 495-31016 495-31022 495-31022 495-31022 495-31022 495-71041 495-81001 495-81001 495-81001 495-81002 495-81002 495-81121 495-81148 495-81153 495-81169 495-81184 495-81184 495-81226 495-81226 495-81226 495-81226 495-81226 495-81226 495-81227 495-81227 495-81227 495-81227 495-81252 495-81259 495-81259 495-81261 495-81282 495-81282 495-81282 495-81282 495-81292 496-21041 496-21041 496-21041 496-21041 496-41041 496-41041 496-41081 496-81000 496-81000 496-81000 496-81010 496-81010 496-81018 496-81018 49773 49773 515-22127 515-22127 515-2295 515-2295 515-23127 515-23127 515-23127 515-23127 515-23127 515-23127

6-3 9-103 3-7 4-23 4-23 4-29 9-121 4-31 9-97 9-99 9-43 9-99 9-135 9-121 4-17 9-103 9-3 9-5 9-51 9-55 9-55 9-57 9-59 9-61 9-47 9-51 9-55 9-59 4-3 9-77 9-77 7-7 9-11 9-45 9-55 9-61 9-73 2-3 6-23 6-23 9-3 9-27 9-27 9-49 5-19 6-3 6-13 9-103 9-103 2-15 3-7 4-11 5-7 5-7 7-9 9-5 9-127 3-3 4-11 4-11 4-11 4-11 7-9

515-23159 515-23190 515-23190 515-23254 515-2379 515-25159 515-25190 515-25254 555-2 555-2 555-2 604-20040 608-12025 61-31016 613-8016 614-10020 614-10020 614-10020 614-10020 614-10020 614-10020 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10025 614-10030 614-10030 614-10030 614-10030 614-10030 614-10030 614-10030 614-10030 614-10030 614-10035 614-10035 614-10050 614-12016 614-12030 614-12030 614-12035 614-12040

5-7 5-7 8-21 8-21 8-41 8-39 8-59 8-19 4-23 4-25 4-25 9-49 6-3 8-119 2-45 5-3 5-9 6-21 8-9 9-53 9-83 4-19 7-7 7-13 7-13 8-7 8-9 8-39 8-41 8-45 8-45 8-47 8-49 8-53 9-21 9-31 9-37 9-41 9-53 9-79 9-91 9-91 9-91 9-91 9-93 9-93 5-3 5-7 6-29 6-31 8-21 8-35 8-51 8-55 9-101 9-27 9-83 9-53 6-35 8-7

31 29 15A 15 20 10 22 13 4 2 8 4 12 23 4 7 7 2 2 11 7 20 10 6 24 11 19 12 5A 4 13 13 5 47 2 42 16 3 7 7 5 10 22 28 3 16 8 26 7 7 32 53 33 24 4 4 8 18 2 18

614-12040 614-18035 614-20040 614-6016 614-6016 614-6016 614-6016 614-6016 614-6016 614-6016 614-6016 614-6020 614-6020 614-6020 614-6020 614-6020 614-6025 614-6025 614-6050 614-8012 614-8016 614-8016 614-8016 614-8016 614-8016 614-8016 614-8018 614-8020 614-8020 614-8020 614-8020 614-8020 614-8020 614-8022 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8025 614-8030 614-8030 614-8030 614-8030 614-8030 614-8030 614-8030 614-8030 614-8030 614-8045 614-8045 614-8045 619387R1

9-105 8-3 6-23

9 27

625743C1 626-10016 627-10030

9-103 8-51 9-83 3-9 9-3 9-3 9-5 9-7 9-11 9-27 9-35 4-43 8-49 9-3 9-35 9-115 9-43 9-115 6-57 2-5 2-3 2-3 3-5 6-37 7-9 9-79 6-27 2-7 2-25 2-27 4-9 5-3 9-27 6-47 3-9 4-41 8-21 8-25 8-27 8-29 8-33 8-49 9-9 9-29 9-29 9-97 9-139 6-65 7-7 7-9 9-13 9-97 9-99 9-139 9-141 9-143 7-7 9-97 9-101 5-17 5-17 6-23 2-11

Bur 7-3350

20 9 9 16 21 8 24 10 16 13 13 10 4 20 12 17 9 22 32 4 25 35 13 42 17 31 3 12 12 11 19 30 7 32 21 38 6 29 17 25 20 5 9 5 9 3 24 18 25 6 7 24 42 30 12 17A 8 16 5 13 15 26 15

3 7 12 32 7 15 16 30 13 17 22 13 15 30 24 4 20 17 7 22 33 31 25 21 28 11 4 23 9 8 10 12 2 23 9 16 14 14 13 13 3 15 2 20 12 13 13 2 5 8 14 12 28 19 28 27 19 11 2 3 26 6



10-25


PAGE REF.

627-10030 627-10030 627-10035 627-10035 627-10035 627-12030 627-12030 627-20040 627-20040 628-6016. 637-62081 637-72081 637-72081 65457C1 65457C1 65457C1 65457C1 65457C1 65457C1 65457C1 6545701 65457C1 65457C1 65881H 680187C169129201 697494R91 70-12532 ' 70-12532 70973 711-10030 711-10040 711-6050' 71121 712998R91 733-2012 760-14413 761-17325 781-24613 781-24820 781-24820 781-24830 800-1134 800-2136 800-40065 800-40070 800-4155 800-435 800-44040 800-44040 800-44040 800-44040: 800-44040 800-44040 800-44050 800-44050 800-44050 800-44050 800-5120 806-8016 806-8025 806-8040 ,806-8050

2-11 9-145 6-23 8-69 9-145 3-9 9-77 3-3 9-79 3-17 4-11 2-39 3-17 8-79 8-81 8-85 8-99 8-101 8-103 8-105 8-109 8-113 8-115 4-33 3-17 3-17 5-11 4-33 4-33 2-7 8-63 8-65 8-65 8-119 6-7 8-49 4-45 4-45 4-11 4-17 9-147 9-97 6-13 6-67 9-47 9-47 9-49 3-9

Bur 7-3350

V

9-11 9-11 9-13 9-13 9-53 9-59 5-15 5-15 6-3 9-11 6-65 • 2-3 2-7. 9-127 .

2-3

9 13 16 20 24 26 .16 2 2 21 30A 16A 27A 4 4 4 4 4 4 4 4 4 4 15 9 8 30 5 10 3 30 14 17 2 7 12 14 8 , 34 ' 3 14 4 17

26 27 31 25 7 , 26 • 31 4 22 5 27 4 10 7 8 5 6 .

11 6 10

PART NO. 811-10070 814-10040 814-10040 814-10040 814-10040 814-10040 814-10040 814-10040 814-10040 814-10040 814-10040 814-10045 814-10045 814-10045 814-10045 814-10050 814-10050 814-10050 814-10050 814-10050 814-10055 814-10055 814-10055 814-10060 814-10060 814-10060 814-10060 814-10070 814-10070 814-10070 814-10080 814-10090 814-10090 " 814-10100 814-10140 814-10150 814-10180 814-10245 814-10245 814-12045 814-12045 814-12045 814-12045 814-12045 814-12045 814-12045 814-12045 814-12050 814-12060 814-12060 814-12080 814-12080 814-12080 814-12080 814-12085 814-12090 814-12100 814-12100 814-12100 814-12100 814-12110 814-12110 814-14140

PAGE REF.

PART NO.

9-81 4-9 8-11 8-13 8-13 8-15 8-17 8-19 8-51 9-3 9-127 3-5 8-35 8-49 9-79 2-3 8-5 8-37 8-43 8-47 8-31 8-33 8-35 4-11 7-13 8-21 •9-27 2-3 8-41 8-55 9-19 8-69 9-19 4-9 8-61 6-29 .8-51 4-13-' 4-15 3-7 8-21 8-23 8-25 8-27 8-29 8-33 8-37 8-41 8-29 8-33 8-25 8-27 8-29 8-33 2-15 8-55 8-25 8-27 8-29 8-33 2-15 9-91 6-59

814-16110 814-6035 814-6060 814-8035 814-8035 814-8035 814-8035 814-8035 814-8040 814-8045 814-8050 814-8060 814-8060 814-8075 814-8080 814-8080 814-8110 824-1405 824-1405 825-11418 825-11418 825-11418 825-1410 825-2406 825-2406 825-2408 825-2408 825-2408 , 825-2408 825-2408 825-2410 825-2410 825-2410 825-2410 827-10040 827-10050 827-10075 827-10110 827-10130 827-12045 827-12045 827-16110 827-16110 827:20075 827-20170 827-20170 827-20190 827-20230 827-8050 827-8060 828-10060 828-10090 828-12055 828-20160 828-20160 829-1306 829-1310 829-1312 829-1406 829-1406 829-1406 829-1406 829-1406

39 2 9 7 20 36 6 8 34 29 9 38 41 18 30 23 33 14 53 5 38 30 49 27 30 22 8 28 5 10 20 13 16 5 . 4 9 3 6 7 ; 3 2 2 2 2 2 2 2 3 ; 27 27 37 31 23 23 ' 5 6 18 18 17 17 2 16 9,

PAGE REF. 6-23 7-3 8-41 2-27 4-13 4-31 9-97 9-101 7-7 9-117 3-9 6-33 6-51 •2-35 6-49 6-65 4-41 4-11 4-47 5-19 6-3 6-13 4-5 4-21 9-141 3-15 9-139 9-139 9-141 9-147 3-17 9-91 9-91 9-93 9-145 8-45 6-15 9-145 • 9-145 6-3 6-3 9-77 9-77 9-47 9-75 9-75 9-13 6-55 .7-13 7-13 8-65 8-67 6-23 9-15 9-17 3-17 8-117 8-117 6-57 8-41 8-65 9-3 9-35

31 10 17 8 15 8 20 8 15 15A 9 16 7 29 34 14 4 10 • 17 "8 2 25 .43 4 27 6 8 30 21 10 24 6A 27 19 16 9 3 19 8 14 21 10 18 13 2 6 16 4 10 10A 25 30 9 6 7 20 13 11 20 19 20 32 25



10-26


PAGE REF.

PART NO.

PAGE REF.

PART NO.

PAGE REF.

829-1406 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1408 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1410 829-1412 829-1412 829-1412 829-1412 829-1412 829-1412 829-1412 829-1412 829-1412 829-1412 829-1416

9-43 2-7 4-11 4-13 4-21 4-41 5-3 7-7 7-9 7-13 8-21 9-9 9-13 9-115 9-139 2-11 3-5 4-19 7-7 7-13 7-13 8-7 8-11 8-13 8-13 8-13 8-17 8-17 8-21 8-21 8-39 8-41 8-43 8-45 8-45 8-47 8-47 8-49 8-51 8-51 8-63 8-65 8-65 8-67 8-69 8-69 8-69 8-69 9-53 9-79 9-91 9-93 6-3 8-7 8-21 8-23 8-25 8-27 8-29 8-33 8-37 9-91 9-77

829-1416 829-1416 829-1420 829-1420 829-1420 829-1420 829-1420 829-1420 829-2410 83-1108 832-10404 832-10404 832-10406 832-10406 832-10406 832-10408 832-10408 832-10408 832-10408 832-10408 832-10408 832-10408 832-10408 832-10408 832-10408 832-10408 832-10408 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10410 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10412 832-10416 832-10420

9-77 9-77 6-55 9-13 9-47 9-75 9-75 9-83 4-11 8-49 9-97 9-99 4-19 4-19 4-25 4-21 4-41 7-7 9-29 9-29 9-97 9-97 9-99 9-101 9-117 9-137 9-143 2-3 8-19 8-31 8-33 8-35 8-35 8-35 8-37 8-55 9-19 9-19 9-19 9-31 9-37 9-41 9-81 9-91 9-99 9-121 9-127 9-145 2-15 3-7 6-23 8-25 8-25 8-27 8-27 8-29 8-29 8-29 8-33 8-33 8-33 6-23 9-15

832-10420 832-41306 833-40406 833-40406 833-40406 833-40406 833-40406 833-40406 833-40406 833-40406 833-40408 833-40408 833-40408 833-40408 836-4065 838-3640 83822C1 84-2106 840-1516 840-1535 842-1425 842-1425 843-1516 844-10020 844-10020 844-10020 844-10020 844-10025 844-10025 844-10110 844-6025 844-6025 844-6025 844-6025 844-8016 844-8020 844-8020 844-8025 844-8025 845-6012 845-6015 845-6020 845-6020 845-8016 845-8016 845-8020 845-8025 845-8025 845-8025 845-8030 845-8035 845-8035 845-8040 845-8050 845-8060 845-8070 854-10065 854-10070 854-10075 854-12025 854-12025 854-12030 854-12040

9-17 3-17 4-23 9-11 9-95 9-115 9-115 9-115 9-137 9-141 2-7 9-97 9-99 9-101 2-37 3-9 9-141 8-49 9-115 4-17 9-97 9-99 4-47 4-11 4-13 4-19 9-9 4-11 4-13 9-19 4-19 4-19 4-21 4-25 2-39 4-23 9-115 3-11 4-21 3-17 2-43 9-137 9-141 2-31 2-41 2-23 2-17 2-33 3-11 2-17 2-29 2-33 2-17 2-19 2-19 2-33 2-21 2-17 2-41 2-19 2-41 2-33 2-45

Bur 7-3350

5 6 8 14 25 7 11 28 7 15 18 17 11 24 16 10 35 21 12 8 21 29 13 11 17 23 10 15 26 34 14 7 57 6 12 8 12 7 5 36 31 16 28 33 7 11 16 24 21 34 31 5 22 19 4 4 4 4 4 4 4 21 14

22 26 7 19 15 4 8 13 20 24 28 6 11 24 11 5 11 17 3 21 13 22 14 10 15B 17 23 26 15 39 32 43 50 54 16 26 8 18 22 44 17 4 41 12 11 25 15 23 9 8 11 19 39 19 33 18 25 28 18 25 28 34 8

10 42 5 15 6 12 22 14 26 13 18 17 12 6 16 6 28 19 9 26 4 15 16 3 22 9 25 11 6 10 23 2 9 17E 3 3 21 6 39 9 13 25 5 21 11 15 16 6 13 5 14 12 6 22 13 3 18 33 17 29 8 2



10-27

NUMERICAL INDEX PART NO. 863-6020 864-10025 864-12130 864-6020 864-6025 864-6035 864-8016 864-8020 864-8025 892-11005 892-11005 .892-11006 892-11006 892-11006 892-11006 892-11006 892-11006 892-11006 892-11006 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11008 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 - 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010 892-11010

Bur 7-3350

PAGE REF. 7-3 6-35 6-59 6-49 6-33 7-3 7-3 6-49 6-35 4-5 4-47 , 3-9 3-17 4-3 6-57 8-49 8-65 9-27 9-115 3-9 3-9 4-21 4-31 7-7 7-9 7-13 8-21 8-25 8-27 8-29 8-33 9-13 9-27 9-97 9-99 9-139 9-147 4-5 7-7 7-13 7-13 8-11 8-13 8-13 8-13 .8-15 8-17 8-17 8-19 8-21 8-47 8-51 8-61 8-65 8-65 8-67 8-69 8-69 8-69 8-69 9-53 9-79 9-101

25 17 10 8 7 19 4 21 6 40 16 33 19 11 19 17 19 19 21 10 24 24 9 3 6 14 17 15 15 14 14 10 14 15 16 15 15 42 11 7 22 12 10 16 22 37 9 16 9 33 7 35 6 15 27 32 6 10 15 23 12 .31 5

PART NO. 892-11012 892-11012 892-11012 892-11018 893-11005 893-11006 893-11008 895-11004 , 895-11004 895-11004 895-11005 895-11006 895-11006 895-11006 895-11006 895-11006 895-11006 895-11006 895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 •895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 895-11008 895-11010 895-11010 f 895-11010 ' 895-11010 895-11010 895-11010 895-11010 895-11010 895-11010 : 895-11010 895-11010 • 895-11010 895-11010 895-11010 895-11010 895-11010 : 895-11010 895-11010 895-11010 895-11010 895-11010 895-11010 895-11010 895-11010 895-11010 895-15006 895-15006

PAGE REF.

PART NO.

27 5

895-15008. 895-15008 895-15008 895-15008 895-15008 895-15008 895-15010 895-18010 896-11010 896-11010 896-11010 896-11010 896-11010 896-11010 896-11010 896-11010 896-11010 896-11010 896-11010 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11012 896-11020 896-11020 896-11020 896-11020 896-11020 896-11020 896-11020 896-11020 896-11020 896-11020 896-15012 896-15012 896-15012 896-15012 896-15012 90-6682T1 90-6682T1 90-668211 90-668211 905794R1 905839R1 905876R1 91946C1 91947C1 933697R1 934667R1 934667R1 934667R1 934667R1 934727R1 96790C2

3-9 9-103 9-105 8-51 4-45 4-21 4-41 4-47 9-97 9-99 3-9 3-9 3-17 6-57 8-41 8-49 8-65 9-27 2-3 2-5 2-7 2-27 3-9 4-41 4-41 7-9 8-49 9-9 9-13 9-27 9-97 9-101 9-119 9-125 9-139 9-143 3-5 6-21 7-13 8-9 8-15 8-19 8-41 8-45 8-47 8-49 8-51 8-61 9-11 9-19 9-19 9-53 9-91 9-91 9-91 9-91 9-93 9-93 9-93 9-101 9-127 4-25 9-115

8 15 3 3 11 27 5 6 34 18 18 18 16 18 18 11 8 5 6 11 6 10 20 4 16 9 13 21 9 26 15 14 22 34 3 31 3 38 14 6 14 14 6 4 5 20 17 21 ' 20 6 11 ' 23 29 4 6 17 6 10 10

PAGE REF. 2-3 2-7 3-5 4-13 9-79 9-127 8-63 9-43 2-11 8-11 8-13 8-55 9-3 9-21 9-91 9-145 9-145 9-145 9-145 3-7 8-21 8-23 8-25 8-27 8-29 8-33 8-37 8-41 9-53 9-77 9-91 9-103 3-3 6-55 9-13 9-15 9-17 9-43 9-47 9-75 9-75 9-79 2-15 2-15 6-23 9-91 9-91 6-3 6-19 6-25 6-69 6-35 6-9 6-13 4-33 4-33 3-17 6-29 6-31 6-49 6-51 6-9 8-49

7 12 32 13 29 7 35 19 8 11 9 25 29A 3 14 9

14 22 26 4 3 3 3 3 3 3 '3 4 22 17 34 118 3A 5 18 9 9 11 14 3 7 3A 3 8 28 17 20 16 12 40 12 20 4 23 2 8 7 3 3 36 6 2 10



10-28


PAGE

REF.

96846C2 97252CX 97256C3 97257C3 97258C3 97259C3 97277C1 97278C1 97290C1

8-49 9-139 9-123 9-123 9-123 9-123 9-123 9-123 9-113

11

Bur 7-3350

PART NO.

PAGE R E F .

PART NO.

PAGE R E F .

1 2 3 4 23 13 2


MANUAL DE PARTES RETRO CASE 580SL SERIES 2 .pdf

Recommend Documents