MA5616 Configuration Script

MA5616 Configuration Script root mduadmin enable config

vlan 17 standard vlan xxx smart vlan 2077 smart vlan 2078 smart

//HSI VLAN

interface vlanif 17 ip address 192.168.231.37 255.255.255.248 quit

//AFTER/digit be used

port vlan 17 0/0 1 port vlan xxx 0/0 1 port vlan 2077 0/0 1 port vlan 2078 0/0 1 ip route-static 0.0.0.0 0.0.0.0 192.168.231.38

service-port vlan 1320 vdsl mode ptm 0/1/0 multi-service user-vlan 10 rx-cttr 6 tx-cttr 6 service-port vlan 2077 vdsl mode ptm 0/1/0 multi-service user-vlan 12 rx-cttr 6 tx-cttr 6

service-port vlan 18 vdsl mode ptm 0/1/0 multi-service user-vlan 11 rx-cttr 6 tx-cttr 6 service-port vlan 1320 vdsl mode ptm 0/2/0 multi-service user-vlan 10 rx-cttr 6 tx-cttr 6 service-port vlan 2077 vdsl mode ptm 0/2/0 multi-service user-vlan 12 rx-cttr 6 tx-cttr 6 service-port vlan 18 vdsl mode ptm 0/2/0 multi-service user-vlan 11 rx-cttr 6 tx-cttr 6 service-port vlan 1320 vdsl mode ptm 0/3/0 multi-service user-vlan 10 rx-cttr 6 tx-cttr 6 service-port vlan 2077 vdsl mode ptm 0/3/0 multi-service user-vlan 12 rx-cttr 6 tx-cttr 6

service-port vlan 18 vdsl mode ptm 0/3/0 multi-service user-vlan 11 rx-cttr 6 tx-cttr 6 service-port vlan 1320 vdsl mode ptm 0/4/0 multi-service user-vlan 10 rx-cttr 6 tx-cttr 6 service-port vlan 2077 vdsl mode ptm 0/4/0 multi-service user-vlan 12 rx-cttr 6 tx-cttr 6 service-port vlan 19 vdsl mode ptm 0/4/0 multi-service user-vlan 11 rx-cttr 6 tx-cttr 6 [public-config] timezone GMT+ 03:00 time time-stamp local snmp-agent community read public snmp-agent community write private snmp-agent sys-info version v1 v2c snmp-agent target-host trap-hostname u2k1 address 172.20.69.201 udp-port 162 trap-paramsname u2k1 snmp-agent target-host trap-hostname u2k2 address 172.20.69.202 udp-port 162 trap-paramsname u2k2 snmp-agent target-host trap-hostname u2k3 address 172.20.69.203 udp-port 162 trap-paramsname u2k3 snmp-agent target-host trap-hostname u2k4 address 172.20.69.204 udp-port 162 trap-paramsname u2k4 snmp-agent target-host trap-hostname u2k5 address 172.20.69.205 udp-port 162 trap-paramsname u2k5 snmp-agent target-host trap-hostname u2k6 address 172.20.69.206 udp-port 162 trap-paramsname u2k6 snmp-agent target-host trap-hostname u2k7 address 172.29.35.201 udp-port 162 trap-paramsname u2k7 snmp-agent target-host trap-hostname u2k8 address 172.29.35.202 udp-port 162 trap-paramsname u2k8 snmp-agent target-host trap-hostname u2k9 address 172.29.35.203 udp-port 162 trap-paramsname u2k9 snmp-agent target-host trap-hostname u2k10 address 172.29.35.204 udp-port 162 trap-paramsname u2k10 snmp-agent target-host trap-hostname u2k11 address 172.29.35.205 udp-port 162 trap-paramsname u2k11 snmp-agent target-host trap-hostname u2k12 address 172.29.35.206 udp-port 162 trap-paramsname u2k12 snmp-agent target-host trap-paramsname u2k1 v1 securityname private snmp-agent target-host trap-paramsname u2k2 v1 securityname private snmp-agent target-host trap-paramsname u2k3 v1 securityname private snmp-agent target-host trap-paramsname u2k4 v1 securityname private

snmp-agent target-host trap-paramsname u2k5 v1 securityname private snmp-agent target-host trap-paramsname u2k6 v1 securityname private snmp-agent target-host trap-paramsname u2k7 v1 securityname private snmp-agent target-host trap-paramsname u2k8 v1 securityname private snmp-agent target-host trap-paramsname u2k9 v1 securityname private snmp-agent target-host trap-paramsname u2k10 v1 securityname private snmp-agent target-host trap-paramsname u2k11 v1 securityname private snmp-agent target-host trap-paramsname u2k12 v1 securityname private snmp-agent trap enable standard

autosave on autosave interval 1440

MA5616(config)#emu add 2 POWER4830 0 0 RS485 POWER4830 MA5616(config)#interface emu 2

//checking by dis emu

MA5616(config-if-power4830-2)#power outside_digital 3 available-level low-level name SPD MA5616(config-if-power4830-2)#power outside_digital 0 available-level low-level name batterydoor-alarm MA5616(config-if-power4830-2)#power outside_digital 5 available-level low-level name HEX MA5616(config-if-power4830-2)#power outside_digital 6 available-level low-level name passivedoor-alarm MA5616(config-if-power4830-2)# power environment temperature 72 -5 80 -20 This command is invalid unless in the contition of install the sensor, would you continue? (y/n) [n]:y MA5616(config-if-power4830-2)# power environment humidity 80 0 100 0 This command is invalid unless in the contition of install the sensor, wouldyou continue? (y/n) [n]:y MA5616(config-if-power4830-2)# power battery parameter 1 0.15 60 15 MA5616(config-if-power4830-2)# power battery temperature 80 -20 56 -15 80 MA5616(config-if-power4830-2)# power battery-test auto-test off-test forbid time-test permit 180 1 MA5616(config-if-power4830-2)#power temperature-off battery-off-state permit battery-offtemperature 58 Power supply-parameter 280 180 58 51

MA5616(config)#interface emu 0 MA5616(config)#interface emu 0

//No need

MA5616(config-if-h831vesc-0)#esc digital 0 available-level high-level MA5616(config-if-h831vesc-0)#esc digital 1 available-level high-level MA5616(config-if-h831vesc-0)#esc digital 2 available-level high-level a MA5616(config-if-h831vesc-0)#esc digital 3 available-level high-level

btv igmp bandwidthCAC disable btv igmp user add 0 service-port 2 no-auth quickleave mac-base max-program 8 igmp user add 1 service-port 5 no-auth quickleave mac-base max-program 8 igmp user add 2 service-port 8 no-auth quickleave mac-base max-program 8 igmp user add 3 service-port 11 no-auth quickleave mac-base max-program 8 multicast-vlan 2078 igmp version v2 igmp priority 4 igmp multicast-vlan member 0 igmp multicast-vlan member 1 igmp multicast-vlan member 2 igmp multicast-vlan member 3 igmp mode proxy igmp program add batch ip 232.0.2.1 to-ip 232.0.2.254 priority 4 igmp program add batch ip 232.0.3.1 to-ip 232.0.3.254 priority 4 igmp program add batch ip 232.0.4.1 to-ip 232.0.4.6 priority 4 igmp uplink-port 0/0/1

DC-VOLTAGE-LACK ALARM TEST Interface emu 2 Display power system paremeter

CASCASDING MA5616 CONFIG MA5616(config) interface eth 0/0 MA5616config-if-eth-0/0) network-role 0 cascade MA5616(config) btv AUAL_D258(config-btv)#igmp cascade-port 0/0/0

FTP TEST MA5616 CONFIG AUAL_D258(config)#service-port vlan transparent vdsl mode ptm 0/1/1 other-al l rx-cttr 6 tx-cttr 6

Important Commands: //MA5616(Config)#Dispaly service-port //MA5616(Config)#interface eth 0/0 Ma5616(Interface eth 0/0)#displauy port ddm-info 1 //MA5616(Config)# display vlan 17 //MA5616(config)#display service-port all //MA5616(config)#display board 0/0 //MA5616(config)#display ip routing-table