m7

1. What is the total amount of level 3 cache that the M7 processor supports ? Mark for Review (1) Points 32 Mbytes 64 Mbytes (*) 128 Mbytes 256 Mbytes

[Correct]

Correct! 2.

How many DIMM slots are supported by the M7 processor?

Mark for Review (1) Points 16 (*) 32 64 128

[Correct]

Correct! 3.

Which is the function of the Mystic River ASIC?

Mark for Review (1) Points Memory Buffer I/O Hub (*) Service Processor Disk Controller

[Incorrect] ssor Overview.”

Incorrect. Please refer back to the lesson “SPARC M7 Proce

4. How does the M7 processor implement SSM within its silic on? Mark for Review (1) Points By improving the crytography performance within the M7 processor chip By implementing 8 DAX units to function as co-processors (*) By increasing the size of the instruction pipeline By implementing increasing the cache size



5.

Which response is the definition of a DAX?

Mark for

Review (1) Points (Choose all correct answers) A co-processor chip that offloads the data compression and decompression functions from the software threads A co-processor with the M7 processor that offloads the data compression and decompression functions from the software threads (*) A memory control unit within the M7 processor A memory control unit chip outside of the M7 processor (*)



Page 1 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y

ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC M7 Processor Architecture (Answer all questions in this section) 6. How many layers of cache does the SPARC M7 processor hav e? Mark for Review (1) Points 1 2 3 4 (*)

[Correct]

Correct! 7.

Which systems use the SPARC M7 processor?

Mark for

Review (1) Points (Choose all correct answers) SPARC M6-32 SPARC T7-2 (*) Oracle SuperCluster T5-8 SPARC T7-4 (*) Oracle SuperCluster M7 (*)


connection? (1) Points


8. Which type of link is an inter-processor cache coherent Mark for Review

SLINK SP LINK CLINK (*) IL



9.

Which type of DIMMs are supported by the M7 processor?

Mark for Review (1) Points DDR5 DDR4 (*) DDR3 DDR2



10. How many virtual CPUs can the M7 support considering tha t each thread can be a virtual CPU? Mark for Review (1) Points 32 64 128 256 (*)



Page 2 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC M7 Processor Architecture (Answer all questions in this section) 11. Which two features are part of the SPARC M7 processor’s po wer management features ? Mark for Review (1) Points (Choose all correct answers) Dynamic Voltage Frequency Scaling (*) Dynamic memory allocation Voltage Acclimatization power gating (*)



12.

Which three statements are true about M7 processors?

Mark for Review (1) Points (Choose all correct answers) Each M7 processor provides coherency links, referred to as CLINKs (*) CLINKS are used on both the M7 and T7 servers (*) Level 4 cache is one of the most important processor enhancements CLINKS provide for inter-processor connections (*) SSM is also a common features with Intel Processors



13.

Which statement is true?

Mark for Review

(1) Points The S4 supports 16 threads per core The SPARC M7 processor uses the fourth generation CMT Core, referred to as S4 (*) The SPARC M7 processor uses the fourth generation CMT Core, referred to as S3. The S3 supports 16 threads per core



14. What enhancements to the SPARC M7 processor contribute t o security at all layers of the stack? Mark for Review (1) Points 4 layers of cache Increased password protection Improvements to on-chip cryptography (*)



SPARC T7 Servers Overview (Answer all questions in this section) 15. rate and power on? (1) Points Single fan

Which can fail, yet allow the T7 servers continue to ope Mark for Review

Single power supply (*) Single fan and and single power supply

[Incorrect] r Overview.”

Incorrect. Please refer back to the lesson “SPARC T7 Serve

Page 3 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC T7 Servers Overview (Answer all questions in this section) 16.

What is the benefit of VersaBoot?

Mark for Review

(1) Points Boots the operating system from a versatile drive Boots Solaris’s root filesystem from firmware-accessible storage Boots Solaris s root filesystem from firmware-inaccessible storage (*)

[Correct]

Correct!

17. How many processor chips does the SPARC T7-4 server have ? Mark for Review (1) Points 1 SPARC M7 32-core 4.13Ghz CPU 2 SPARC M7 32-core 4.13Ghz CPUs 4 SPARC M7 32-core 4.13Ghz CPUs (*)

[Incorrect]


r Overview.” 18.

What are two benefits of DIMM sparing? Mark for Review

(1) Points (Choose all correct answers) 1 out of 16 DIMMs per socket can be spared (*) 2 out of 16 DIMMs per socket can be spared Migration of contents from failing DIMM takes place, with minor impact o n performance Migration of contents from failing DIMM takes place, with no visible imp act on performance (*)



19. Which components are located in a single T7-4 server pro cessor module? Mark for Review (1) Points 2 CPUs, 32 DIMM slots, 12 BoBs (*) 4 CPUs, 64 DIMM slots, 24 BoBs 4 drive bays, 2 IOHs, server processor module 8 drive bays, 4 IOHs, server processor module



20. How many processor chips does the SPARC T7-2 server have ? Mark for Review (1) Points 1 SPARC M7 32-core 4.13Ghz CPU 2 SPARC M7 32-core 4.13Ghz CPUs (*)

4 SPARC M7 32-core 4.13Ghz CPUs



Page 4 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC T7 Servers Overview (Answer all questions in this section) 21. How many processor chips does the SPARC T7-1 server have ? Mark for Review (1) Points 1 SPARC M7 32-core 4.13Ghz CPU (*) 2 SPARC M7 32-core 4.13Ghz CPUs 4 SPARC M7 32-core 4.13Ghz CPUs



22. Which can fail, yet allow the T7 servers continue to ope rate? Mark for Review (1) Points Single fan Single power supply Single fan and and single power supply (*)



23.

What are two benefits of NVMe? Mark for Review

(1) Points (Choose all correct answers) PCIe based SSD (*) Lower performance than SAS Higher performance than SAS (*) Lower Performance than SATA Higher performance than SATA



24.

Which three statements are true?

Mark for Review

(1) Points (Choose all correct answers) The SPARC T7-1 is the replacement for the SPARC T4-1 server (*) The SPARC T7-1 server uses XSCF as its systems management The SPARC T7-2 is the replacement for SPARC T5-2 server (*) The SPARC T7 servers use the new SPARC T7 microprocessor SPARC T7-4 is the replacement for the SPARC T5-4 server (*)

[Correct]

Correct!

25. Which components are located in a T7-4 server main modul e? Mark for Review (1) Points 2 CPUs, 32 DIMM slots, 12 Bobs

4 CPUs, 64 DIMM slots, 24 BoBs 8 drive bays, 4 IOHs, server processor module (*) 4 drive bays, 2 IOHs, server processor module



Page 5 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC T7 Servers Overview (Answer all questions in this section) server? (1) Points

26. What is the maximum memory configuration in a SPARC T7-1 Mark for Review

16 DIMM slots with memory mezzanine (*) 32 DIMM slots with memory risers 64 DIMM Slots


server? (1) Points



16 DIMM slots with memory risers 32 DIMM slots with memory mezzanines

64 DIMM slots (*)


server? (1) Points



16 DIMM slots with memory mezzanine 32 DIMM slots with memory risers (*) 64 DIMM slots

[Correct]

Correct!

SPARC T7 Servers Installation 29. Which resource are you required to use at a customer sit e for server installation? Mark for Review (1) Points Site Requirements Product Documentation EIS Installation Checklists (*)

[Incorrect] r Installation.” 30.


What do you type to power on a SPARC T7server? Mark for

Review (1) Points Start / system (*) Root and changeme Host and changeme

[Incorrect] r Installation.”


Page 6 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC T7 Servers Installation 31.

When installing a SPARC T7 server in a rack you should?

Mark for Review (1) Points Load servers into the rack from the middle Load servers into a rack from the top down Load servers into a rack from the bottom up (*)



32. What is a key benefit of Automated Service Request (ASR) ? Mark for Review (1) Points ASR provides installation self-service requests ASR sends every possible fault or flaw messages to Oracle immediately fo r service ASR software resolves problems faster by automatically opening service r equests for Oracle s qualified server products when specific faults occur (*)



33. What piece of equipment is required when installing a SP ARC T7-2 and SPARC T7-4 server into a rack? Mark for Review (1) Points Lift (*) Hex wrench Hex screwdriver



34. What do you type to login to the SP in a SPARC T7 server ? Mark for Review (1) Points Start / system Root and changeme (*) Host and changeme

[Correct]

Correct! 35.

What is the CMA?

Mark for Review

(1) Points Cable Management Arm (*) Cable Movement Action Connect Management System



Page 7 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment

Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC T7 Servers Installation 36. What are two options that can function as a systems cons ole during the SPARC T7 installation? Mark for Review (1) Points (Choose all correct answers) iPhone ASCII terminal (*) Workstation (*) Kindle

[Correct]

Correct!

37. Which one of these SPARC T7 server installation hardware steps are in the correct order? Mark for Review (1) Points Adjust the CMA, attach data and management cables to the server, and ins tall the server into a rack. Install the server into a rack, attach data and management cables to the server, and adjust the CMA. (*) Install the server into a rack, adjust the CMA, and attach data and mana gement cables to the server.

[Correct]

Correct!

38. Which one of these SPARC T7 server installation steps ar e in the correct order? Mark for Review (1) Points Prepare terminal access, turn on power to the SP, monitor the boot proce

ss via ILOM, and power on the server and set up the operating system. (*) Power on the server and set up the operating system, prepare terminal ac cess, turn on power to the SP, and monitor the boot process via ILOM. Monitor the boot process via ILOM, power on the server and set up the op erating system. prepare terminal access, and turn on power to the SP.

[Incorrect] r Installation.” 39.


What is the password for root in your initial SP login?

Mark for Review (1) Points root changeme (*) admin default

[Correct]

Correct!

40. What is the recommended number of people to install a SP ARC T7 server? Mark for Review (1) Points 1 2 (*) 3




Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC T7 Servers Installation 41.

How can you boot a SPARC T7 server?

Mark for Review

(1) Points Using the VersaBoot process Using the Fallback boot process Using the conventional boot process Using all of these options (*)



SPARC T7 Servers FRU CRU 42.

Which three of these T7-1 server components are FRUs?

Mark for Review (1) Points (Choose all correct answers) SAS SSD DVD drive (*) Motherboard (*) Disk backplane (*) Memory mezzanine

[Incorrect] r FRU CRU.”


43.

Which two of these T7-4 server components are FRUs?

Mark for Review (1) Points (Choose all correct answers) Cable kit (*) Main module Rear IO module Processor module (*) Rear chassis sub assembly



44.

In the T7-4 where is the eUSB is located?

Mark for

Review (1) Points In the main module On the rear IO board (*) In the processor filler module



45.

Which three of these T7-4 server components are CRUs?

Mark for Review (1) Points (Choose all correct answers) Cable kit Main module (*)

Rear IO module (*) Processor module (*) Rear chassis sub assembly



Page 9 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. SPARC T7 Servers FRU CRU 46.


Mark for Review (1) Points (Choose all correct answers) DVD drive (*) Memory riser (*) Disk backplane (*) Fan cage asssembly Power supply backplane



47. Mark for Review (1) Points

To remove the T7-4 rear chassis sub assembly you must:

Remove the front components, remove the rear components, remove the scre ws that secure the RCSA to the chassis from the rear, pull the RCSA from the rea r. Remove the front components, remove the rear components, remove the scre ws that secure the RCSA to the chassis from the front, pull the RCSA from the re ar. (*) Remove the front components, remove the rear components, remove the scre ws that secure the RCSA to the chassis from the front, pull the RCSA from the fr ont.

[Correct]

Correct! 48.


Mark for Review (1) Points (Choose all correct answers) SAS SSD (*) PCIe card (*) Motherboard Disk backplane Memory mezzanine (*)



49.

In the T7-2, to remove the fan cage assembly, you must:

Mark for Review (1) Points Remove the memory mezzanines, remove the fans, remove the cables, pull t he fan cage assembly up out of the server. Remove the memory risers, remove the fans, remove the cables, pull the f an cage assembly up out of the server. Remove the memory risers, remove the fans, remove the cables, remove the

screws that secure memory riser guide and pull it up out of the server, pull th e fan cage assembly up out of the server. (*)



50. In the T7-2, to remove the power supply backplane, you m ust: Mark for Review (1) Points Remove the memory risers, the air baffle, the drives, the power supply r ibbon cable and cover, and the bus bar screws. Remove the memory risers, the air baffle, the power supplies, the power supply ribbon cable and cover, and the bus bar screws. (*) Remove the memory mezzanines, the air baffle, the power supplies, the po wer supply ribbon cable and cover, and the bus bar screws.



Page 10 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section) 51. What tasks occur during the operational handover phase o f the EIS methodology? Mark for Review (1) Points (Choose all correct answers) Collate the EISdocV4 documents pertaining to this customer installation, and product documentation for handover (*) Provide the customer the 20% installation service rebate that is require d after a successful installation

Obtain customer signatures to successful close project Document the serial number for the system(s) installed, as well as any c omments pertaining to the installation (*)

[Incorrect] tent and try again. 52.

Sorry, that is not correct. Please review the course con

What are Oracle Standard System Installations (OSSI)?

Mark for Review (1) Points Installation Services sold by 3rd party service providers Installation Services sold by Oracle Advanced Customer Support (*) Field Delivery Support Services offered through certified partners Advanced professional services offered by IBM Global Services

[Incorrect] tent and try again.


53. What two activities are accomplished during Installation Task Planning step in the EIS Methodology? Mark for Review (1) Points (Choose all correct answers) Networking and system component cabling Communicate schedule for installation to the customer (*) System unpacking and acclimatization Review the timeframe options for delivery of the service Organization of the team who will actively work the Installation (*)



54.

Who is involved in the Project Initiation phase?

Mark for Review (1) Points (Choose all correct answers) Oracle Installation Coordinator or Project Manager (if applicable) (*) Oracle Financing contact 3rd party Service Provider Partner point of contact (*) Customer point of contact (*)



55. What three documents are typically used as part of the E IS Planning and Preparation stage in the installation process? Mark for Review (1) Points (Choose all correct answers) Test Procedures Plan (*) Project Schedule Installation and Configuration Plan (*) Operational Hand-off Form Acclimatization Report Site Audit Report (*)

[Incorrect] tent and try again. Page 11 of 18


Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section) 56. Why should you typically complete the Installation Confi guration Plan and create your Test Procedures Plan at the same time? Mark for Review (1) Points Test Procedures plan is a standard document used in all generic system i nstallations. You should create the Test Procedures Plan after you have completed the system installation and configuration. As you work through the system configuration process with your customer, you should state how you will test key items in the system’s configuration for ha ving been successfully completed. (*)



What is the primary purpose of the”Basic Solaris” standard?

Mark for Review (1) Points Defines a method for achieving a consistent installation for Oracle Serv ers with Solaris OS (*) Describes how to install legacy versions of Solaris on systems that need to support backward compatible applications Specifically describes how to install Solaris on non-SPARC hardware Differentiates between Linux and Solaris installation processes on dualboot systems

[Incorrect]


tent and try again. 58. What are the two primary objectives for the Installation Configuration Planning step of the EIS methodology? Mark for Review (1) Points (Choose all correct answers) Oracle/Partner and Customer will determine and mutually agree upon the h ardware and software installation requirements which will be documented in the I nstallation and Configuration Plan (*) Oracle/Partner confirms power and cooling requirements for system instal lation Customer provides walk-through of installation site Tests that will be performed during the Systems Testing will be defined. (*)



59. What are three items in the EIS Site-Audit Report are do cumented for all Oracle hardware? Mark for Review (1) Points (Choose all correct answers) IP Address requirements Operating Environment and Cooling requirements (*) Operating System requirements Facility Power requirements (*) Access Route requirements (*)



60. What are three types of configuration information typica lly documented in an Installation Configuration Plan? Mark for Review

(1) Points (Choose all correct answers) System host names (*) System documentation and guidelines General and Management Network Configuration (*) IO cards and controllers (*) Power cord specifications Boot Disk Layout (*)



Page 12 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section) 61.

When should you review deliverables and why?

Mark for

Review (1) Points EIS deliverables are used as a last step in the installation process to ensure the installer provided everything that is required Ideally EIS deliverables would be reviewed at the very start of an insta llation project, as they clearly define scope, roles and responsibilities, and p roject deliverables (*) EIS deliverables are included in the Oracle system shipping and packagin g documents near the start of an installation

EIS deliverables are an interim checklist to ensure that at the mid-way point of an installation the project remains on track.



62. Name two functions for the EIS-DVD during the Installati on and Configuration of Oracle Hardware and Software step in the EIS methodology ? Mark for Review (1) Points (Choose all correct answers) Used as a back-up for complete documentation sets that are on http://doc s.oracle.com Contains required patches and firmware for most installations (*) Provides installation assessment and diagnostic tools (*) Provides an excellent tool as a leave behind utility for customers



63. What is the primary goal of the Installation and Configu ration of Oracle Hardware and Software step in the EIS methodology? Mark for Review (1) Points Hardware cabling , wiring and Power ON System acclimatization, installation, and basic configuration (*) Troubleshooting software configuration issues Managing transition from Installation phase to Field Service issue recor ding



64. What are the four key points covered in each test topic of the Test Procedures Plan? Mark for Review (1) Points (Choose all correct answers) Prerequisites Outcome (*) Conclusion Test Result (*) Objective (*) Method (*)



65. tallation process? (1) Points

Why should you use the EIS methodology to guide your ins Mark for Review

The EIS methodology provides a 20% discount on Support Services if you i nstall your customers’ hardware or software using it Using the proven EIS methodology will provide step-by-step installation guidelines, help guarantee a quality installation, make your life easier, and en sure customer satisfaction (*) Larry Ellison has mandated using EIS Installation processes are very lengthy, the EIS methodology is quick an d dirty




Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section) 66. Which four objectives are primary goals for an EIS Site Audit? Mark for Review (1) Points (Choose all correct answers) Determine the floor weight load capacity at the location where the Syste m will be installed (*) Determine how many logical domains need to be configured on the system Determine installation needs for the System, including such assessments as: the suitability of access routes to the installation location, such as doors , elevators, floor strengths and ramps (*) Determine how frequently system backups will be completed Determine the availability of required electrical power to run and maint ain the System (*) Determine the environmental conditions at Customer s site including temp erature, humidity, cleanliness and such other assessments as are determined to b e necessary in Oracle s sole discretion (*)



67. What if the customer has their own labeling methodology that differs from the recommended one from EIS? Mark for Review (1) Points Follow the customer s standard for cable labeling provided it meets with EIS requirements for identification and port location. (*) Ignore the customer’s standard and use the EIS standard Submit a Service Request for Oracle approval on use of the customer labe

ling and routing methods Redo cabling throughout the datacenter to meet the EIS standard



68. If the customer has asked for some customization of thei r installation, how is testing for that accomplished? Choose all responses that apply. Mark for Review (1) Points (Choose all correct answers) Additional tests can be inserted into the Test Procedures plan (*) Oracle is automatically responsible for any non-standard installation pr ocedure, regardless of whether they were agree to as part of the Installation an d Configuration Plan Not all installation actions need testing Testing above and beyond the Covered System Tests are at the sole discre tion of Oracle and/or the Partner installer (*)



69. You are assigned to an installation project in France in February to install 5 new SPARC T5 servers. The servers, in their original pack aging, are sitting in the customer’s loading dock with a temperature of 8 degrees C (46 degrees F). The customer’s data center is 20 degrees C (68 degrees F). What is the recommended next step in acclimating these systems? Mark for Review (1) Points Unpack the servers and store in the loading dock Move the systems (still packed) into the data center Unpack the servers and store in the data center Move the systems (still packed) into a room with a similar environment t o the data center (*)



70. What are two cautions that should be acknowledged when a cclimatizing a system? Mark for Review (1) Points (Choose all correct answers) Avoid unpacking items inside the computer centre (dust/dirt contaminatin g filters etc.) (*) Once powered on the temperature is no longer an issue, as internal cooli ng systems commence Powering ON the system will speed the acclimatization process as the hea t from the system will accelerate its warming The maximum positive or negative temperature gradient that is permitted for multi-layer
boards is approximately 2° C (4° F) per hour. (*)



Page 14 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section) 71. What is the mission statement for use of the Enterprise Installation Standards? Mark for Review (1) Points To drive the ongoing development and usage of Enterprise Installation St andards (EIS), resulting in consistent, high quality, and cost effective install ations that speed time to deployment and provide the foundation for enhanced sta bility and performance. (*) To drive consistent best practices for Oracle Services field delivery

To manage communication and resolution of Services Requests in a timely and customer-friendly manner To use a methodology for support service that is from the field, created by the field for the Field.



72. Why it is important to do Installation planning, rather than just asking the customer as you work through the installation process? (Sel ect three) Mark for Review (1) Points (Choose all correct answers) Planning leads to more thoughtful consideration for a predictable outcom e of the installation process (*) Support Services will not engage on services requests if no installation planning was done Customer technical contact may not be readily available (*) Continuing interruptions can detract from the professionalism of your wo rk, and lead to customer dissatisfaction (*) Pricing for Installation Services is less expensive if planning in not i ncluded



73. ct all that apply. (1) Points

Which Oracle products are covered by EIS Checklists – sele Mark for Review (Choose all correct answers)

OS and Cluster-related Software (*) Engineered Systems (*)

Storage (*) ERP applications Oracle Fusion Middleware Switches (*) Servers (*)



74. Assuming a SPARC T5 Server installation on which you ins tall Solaris 11, what EIS documentation, at a minimum, is it recommended that yo u bring to support you in the installation project? Mark for Review (1) Points (Choose all correct answers) EIS Installation Checklist for Sun Datacenter InfiniBand Switch 36 EIS Installation Checklist for Solaris 11 OS (*) EIS Installation Checklist for SPARC T5 (*) EIS Installation Checklist for Common Array Manager

[Correct]

Correct!

75. What three typical activities are done during the Projec t Initiation phase of the EIS Methodology? Mark for Review (1) Points (Choose all correct answers) System configuration details are documented. The EIS Site-Audit is scheduled (*) Details about the customer are determined and documented (*)

Details about the project are identified and documented, for example, is this a single system installation or a complex, multi-product installation (*) System delivery occurs, and the project commences



Page 15 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section) ons too? (1) Points

76. Why are EIS deliverables relevant for Partner installati Mark for Review

EIS deliverables describe the amount of time, materials and deliverables are in scope for a standard installation (*) When partners use the EIS deliverables and submit documentation to that effect, their customer gets a 25% discount on support EIS deliverables provide flexibility when customers want to make ad-hoc configuration changes Advanced Customer Services mandates that Partners use the EIS methodolog y for installations



Which three responses are true regarding EISdoc v4?

Mark for Review (1) Points (Choose all correct answers)

Is a free guide to configuring Oracle software Is an OpenOffice-based set of documentation that includes planning for i nstallations of Oracle equipment and some software (*) Is available on the partner Enterprise Installations Standards web page and on the EIS-DVD (*) Is accessible to customers and end-users of Oracle hardware and software Contains documents matched to the steps in the EIS Methodology (*)



78. Why is the rate of temperature change when acclimatizing systems such an important factor as described in the EIS methodology? Mark for Review (1) Points Variations in temperature should not exceed the approved gradient of app roximately 2° C (4° F) per hour, because ignoring this may could lead to long-term d amage (hair-cracks) on the boards (*) Variations in temperature do not have as big an impact as do Service con tract considerations for how long an installation will take Systems should be warmed up and powered ON as quickly as possible to opt imize the installation project timeline It is actually not relevant or important



79. Name three of the problems that EIS was created to overc ome? Mark for Review (1) Points (Choose all correct answers) Poor communication/use of Best Practices (*) Lack of formal agreement with customers as to outcome of an installation

(*) Oracle hardware shipping best practices for on-time delivery Standards for delivery of replacement parts for Oracle hardware Inconsistent installations: Customers buying identical servers for two l ocations were dismayed to find different patch levels, firmware versions etc. (* )



80. What are two statements that are true about EIS checklis ts? Mark for Review (1) Points (Choose all correct answers) EIS installation checklists are intended to guide the installer through the installation in a logical and consistent manner (*) Checklists are intended as guidelines for properly trained installers an d are NOT a substitute for appropriate product training. (*) Checklists are a valuable tool to share with customers so they know how to install systems themselves Checklists are publicly available on oracle.com



Page 16 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section)

81.

Which three statements are true about EIS?

Mark for

Review (1) Points (Choose all correct answers) EIS is a quick and dirty process for expediting Oracle system installati ons EIS stands for “Enterprise Installation Standards” (*) EIS evolved from the field, is sustained by those closely involved with the field, and is intended to assist the field (*) EIS is a methodology designed to address issues before, during and after the actual hands-on installation of Oracle systems (*) EIS stands for “Enterprise information Standards”



82. Why do the EIS Standards recommend that external cables between Oracle hardware, such as servers, storage devices, network devices and p orts be clearly labeled? Mark for Review (1) Points Labeling is not an EIS best practice For ease of maintenance it should be unambiguously clear from the label on each cable, where the cable has to be attached (*) Service requests for field diagnostics will not be accepted unless cable s are labeled Cable routing should be done with rubber bands for ease of reconfigurati on

[Incorrect] tent and try again. 83. Mark for Review (1) Points


What is found on the EIS-DVD? Select all the apply.

(Choose all correct answers) Scripts that assist during the installation (*) Selected Oracle/Sun Software (*) Sales and presales technical training on Oracle systems Tools to help verify the quality of the installation (e.g. ORAS/CLI) (*) A complete set all configuration files for every Oracle server, storage system and Engineered system



84. Which four documents are included as part of the Operati onal Handover? Mark for Review (1) Points (Choose all correct answers) Test Procedures Plan (*) System Documentation (*) Site Audit Report (*) MOS Internal Documentation EIS Checklist for the System installed Installation and Configuration Plan (*)



85. Which two EIS documents are most useful during the Insta llation and Configuration of Oracle Hardware and Software step? Mark for Review (1) Points

(Choose all correct answers) DVD Operational Handover Agreement Installation Configuration Plan (*) EIS Checklist (*) Site-Audit Report



Page 17 of 18 Test: SPARC T7 Servers 2015 Hardware Installation Specialist Online Assessment Review your answers, feedback, and question scores below. An asterisk (*) indica tes a correct answer. This 90- question assessment test is the final component of the SPARC T7 Servers Hardware Installation Specialist training. This assessment will allow y ou to test your knowledge of the information learned from the SPARC T7 Servers 2 015 Hardware Installation Specialist guided learning path. Passing with a >80% s core from this assessment makes you eligible to become an SPARC T7 Servers 2015 Hardware Installation Specialist. EIS (Answer all questions in this section) elect two) (1) Points

86. What should partners do before first using ESISdocV4? (S Mark for Review (Choose all correct answers)

Submit their EIS Test Procedure Plan outcomes Review the Openoffice presentation on EISdoc V4 found on the EIS Plannin g & Documentation web page (*) Review Oracle product overview documentation Review the “EISdoc V4 Getting Started Cookbook” and “Success with EISdoc V4 Co okbook” (*)



87. What four tasks are typically happening at the EIS Plann ing and Preparation stage in the installation process? Mark for Review (1) Points (Choose all correct answers) Unpack and power ON systems Notification of Customer Installation project (*) Identify Installation team – Oracle Installation Coordinator, Project Mana ger, Customer Point of Contact, others as needed (*) Compile EIS planning documents (*) Begin work on Project Schedule (*) Cable and install systems into custom rack



What is the primary purpose of the EIS-DVD?

Mark for

Review (1) Points The EIS-DVD is a tool that is provided to installation partners as a giv e-away to customers The EIS-DVD is to help installers of Oracle/Sun products perform consist ent installations in an efficient manner. (*) The EIS-DVD is used for on-the-job tutorials on how to install Oracle se rvers and storage The EIS-DVD is an annually released product which support all hardware i nstallations, and documents all bugs and issues that have been logged during the prior year

[Correct]

Correct!

89. According to the EIS methodology, when issues are uncove red during the Site-Audit, who should be notified? Mark for Review (1) Points (Choose all correct answers) Oracle Premier Support Customer point of contact (*) Oracle sales management Installation coordinator if applicable (*)



90. What should you do if you believe you have found an erro r in an EIS checklist? Mark for Review (1) Points Assume that the EIS team is already aware and the next version of the ch ecklist will be updated Email Larry Ellison and recommend changes Submit your concerns to My Oracle Support Follow the feedback method on the last page of every checklist: email SU [email protected] (*)

[Incorrect] tent and try again. Page 18 of 18


m7

Recommend Documents