Version 1.03
Installationshinweise Regensensor - Lichtassistenz
Artikelnr. 37140
Audi A4 8K A5 8T Q5 8R
www.kufatec.de Kufatec GmbH · Dahlienstr. 15 · 23795 Bad Segeberg · e-mail:
[email protected]
Content General Information 1 2 Requirements of legal regulations for operation ............................................. .............................. 2 3 CAN connector cables 4 Rain sensor connection cable 6 Encoding 7
General Information In developing the product, your personal safety, combined with best operating comfort, modern design and the latest production techniques respected. , Despite the utmost care in case of improper installation or use of, or incorrect Handling personal injury and / or property damage. Therefore, please read the attached instruction manual carefully and completely and You keep this up! All articles of our production through a 100% check - for your safety. We reserve the right to make technical changes at any time, the interest of progress. Depending on the product and purpose, it may be necessary, prior to installation and commissioning to consider the statutory provisions of each country. The unit is in warranty claims in the original packaging with proof of purchase enclosed detailed description of the fault the seller for repair. Please pay attention to t he Return requirements of the manufacturer (RMA). The statutory Warranty regulations. The warranty and also the approval expires by: a) unauthorized modifications to the device or accessories not recommended by the manufacturer or its partners were conducted or approved b) Open the device's c) repairs carried out on the device d) improper use / non-conforming use / operation e) trauma to the device (drop, willful damage, accident, etc.) Install in accordance with all relevant safety and legal directions. The device must only be installed by trained personnel or similarly qualified persons be.
1
Safety The installation must be performed only by trained personnel. Do not install the energized to make. Therefore for example the battery from the electrical system separate note, while the please the specifications of the vehicle manufacturer. ! Never use security screws, bolts or other Attachments to the steering, braking system or other components to make your own Not to endanger road safety. ! Connect the unit only to DC 12V negative ground car on. This unit can not be used in large trucks or other motor vehicles with 24V Board voltage. ! Avoid installing the unit in places which the driving safety or the Other functionality would be limited in built-up vehicle subassemblies. ! This module may only be used in combination with the following vehicles and Series will be used, and the unit is only for use in the Installation instructions mentioned connections are made. • For damage caused by faulty installation, unsuitable connections or result in an assembly is not intended vehicle types and models, assumes the Kufatec GmbH assumes no liability. ! We wish to point out that the module described in the following data from the MOST protocol from the vehicle handles. When installing the module is therefore a model-specific total system accessible to us as a manufacturer of that assembly is only partially known. ! Can Especially with changes within the same model and same model year If our device therefore can not be guaranteed in every case. For a If our device does with other changes made by faulty GmbH assumes no liability. ! The Kufatec GmbH does not guarantee that the installation of the herein described Component to the individual vehicle manufacturers warranty is approved. Please They therefore consider before you begin the installation guidelines and warranty policies Vehicle manufacturer. ! The manufacturer reserves the right to change the device without giving reasons. ! Errors and omissions excepted
Windshield rearview mirror with matching interior mirror bracket required. For some models of exchange from the CAN gateway is required.
Installationshinweise
Abb. 1
1 – Interiro Light Module
2 – Control Unit
3 – CAN Gateway (glove compartment left)
4 – Control Unit
Hinweis:
The harness wires T27/25 und T27/7 are required only if Dimming mirrors are to be retrofitted.
Open the storage compartment of the interior light and loosen the screw needed (Fig. 2).
Abb. 2
Abb. 3
Pry the shield airbags (with a suitable disassembly wedge) from its socket and loosen behind the screw (Fig. 4). NOTE: If the vehicle has airbags for safety reasons it is important to, that the line BEHIND the airbag is not putting tension on it. Attach the Line so that the airbag is not impaired in its function.
Abb. 5 3
Abb. 4
Remove the 8-pin connector (black) and connect the cable as follows. T8b/6
PIN 6
Abb. 6
Loosen the necessary screws from the glove compartment (Fig. 7 - 9) and separate the original Plug connections.
Abb. 7
Abb. 8
Abb. 9
CAN connector cables CAN Gateway Remove the 20-pin connector (red), press the locking cap to the . remove Connect the twisted pair CAN cable as follows. NOTE: If PINs reassigned solderin manufacture or crimp. No use crimp! T20/17 - PIN 17 High
T20/7 - PIN 7 Low
Abb. 10 Abb. 11
4
Furthermore, the panel is to disassemble the steering column below. To the necessary Loosen the screws laterally and below the cover (Fig. 12, 13).
Abb.13
Abb.14
Abb.12
Disassemble the lever for the hood opening and the lining of the left A-pillar. this is the latch (Fig. 15) to remove. Continue to loosen the screw shown in Figure 16
Abb.16
Abb.17
Abb.15
Start with the wiring in the rear of the vehicle (Figure 17-20). Remove the right trunk lid.
Abb.18
Abb.19
5
Abb.20
Remove the 32-pin connector (black), you connect the cable as follows (solder or new Crimp). No use crimp!
T32c/32 - PIN 32
Abb. 21
Rain sensor connection cable Control unit Remove the 16-pin connector (Beige). Connect the cable as follows.
T16b/2 - PIN 2
Abb. 22
Abb. 23
The wiring for ignition and duration Plus Plus are the respective fuse holders to connect. Please check before installation which fuse carrier or continuous positive ignitionleads.
Abb. 24
e management of mass is to be connected with the ground point of the A-pillar. 6
encoding To carry out the vehicle, the vehicle self-diagnosis coding is selected. Please lead the encoding step by step according to the following figures by.
Fahrzeugeigendiagnose
Eigendiagnose
Adresse 19 (CAN Gateway)
008 Codierung
Verbauliste codieren
20 - Fernlichassistent auf „codiert“
Bestätigen mit OK
Codierung durchgeführt
7
Adresse 46 (HighBeam assistant) Byte 06
-
Bit 2 auf 1 setzen
Vehicle SelfDiagnoses
Codierung
xxxxx1xx
Select Address
Self-Diagnoses
Master
BIN anwählen
8
Codierwert eingeben+ bestätigen
Adresse 09 (Control Unit) Byte 22
Byte 05
Byte 06
-
-
Bit 0 auf 1 setzen
xxxxxxx1
(Regen- Lichtsensor)
Bit 6 auf 1 setzen
x1xxxxxx
(Fernlichtassistent)
HEX: AF
(Coming Home, Leaving Home)
Address 20 (high beam assistant) Byte 00
Byte 01
Byte 02
-
-
HEX: 02
(Coming Home, Leaving Home)
HEX: 01
HEX: 98
ON VEHICLES WITH ADDITIONAL MMI 3G - address 5F Byte 07
-
Bit 4 auf 1 setzen
xxx1xxxx
NOTE: The individual lines T27/25 and T27 / 7 are only required when the automatic dimming mirrors are installed. Otherwise, they can be ne glected.
9
