HYDRAULIC HOSE Couplings Couplings , Accessories Acces sories and Equipment
Warning
Caution
■ Bridgestone Products (hereinafter “Products”) are the part of the engineered systems
which are manufactured by Bridgestone and must be assembled and used on the basis of Bridgestone’s instructions, processes and specifications. ■ Failure to follow the warnings set forth on the Products or in this catalog may result
in serious injury or death. In the event users fail to follow usage instructions or specifications, which Bridgestone stipulates in the catalog, Bridgestone neither guarantees the performance of the Products nor is responsible for any other productrelated failures/defects. ■ Bridgestone disclaims any responsibilities or liabilities for any components in the
engineered system which are not designed, engineered or produced by Bridgestone. ■ Bridgestone is not responsible for the performance of the Products assembled by
others in a manner which does not conform to Bridgestone instructions, processes or specifications.
Warning indicates that failure to comply with the instructions may cause personal injury ■ Warning or death. ■ Caution indicates that failure to comply with the instructions may cause personal injury
or property damage.
DISTRIBUTION OF INFORMATION Bridgestone widely distributes the Products and usage information to distributors, sellers and users.
This information is also available on Bridgestone’s website, (www.bridgestone. com/products/diversified/hose). However, However, we also rely on the sellers or distributors of the Products to provide a copy of safety or usage information, including warnings and precautions to all end users. It is imperative to read these warnings and precautions before selecting and utilizing the Products.
1
Precautions For Safety’s sake
1
Be sure to read the following before use.
Bridgestone Hydraulic hose, couplings, and accessories accesso ries are developed develope d for hydraulic components . Follow each product’s application and specification. Avoid hose burst, leakage, and other dangers by following important steps.
1 Proper usage
Warning
Severe personal injury or death may result if these instructions are not followed.
●Do not touch a pressurized hydraulic hose assembly with any part of your body. If hoses, couplings or accessories are broken, and a fluid touches the skin, even if no pain is felt, a serious injury including burns may be caused. In case of JAT/JAM series, be sure to use safety chains. Use of plastic hose guards will help a person avoid injury. ●System working pressure should not exceed the rated working pressure of the hose assembly. Exceeding the rated working pressure of the hose may result in the hose bursting or hose coupling blow-off. Follow the maximum working pressure ratings listed in this catalog. ●Use compatible hydraulic fluid The use of an incompatible hydraulic fluid will deteriorate the inner tube and the reinforcement resulting in the hose bursting or coupling hose coupling blow-off. ●Protect hose from abrasions. If the hose reinforcement is exposed, it is susceptible to rust and accelerated damage leading to serious failure like hose burst. If it is found, replace with a new one. will be twisted or pulled. ● Avoid applications where the hose is or will Twisting or stretching a hydraulic hose under pressure may result in hose bursting or hose coupling blow-off. If it is found, replace with a new one, then install a live swivel joint. ●Do not snap the hose. Snapping and deforming deforming will lead to hose burst, leakage, and hose coupling blow-off. If found, replace with a new one. ●Do not apply an electrical current to a hose assembly. Electrifying a hose may lead to a hose failure or an electric shock. ●Tighten hose assemblies to the recommended torque. If tightening is improper, there are possibilities of leakage, connection connection portion breakage, and separation. separation. Be sure to apply the recommended torque torque by using a torque spanner. In case of over torque, replace with a new one. In case of under torque, retighten with the recommended torque ( page 82 ). ● Avoid the usage exceeding the minimum bending radius The usage exceeding the minimum bending radius may may cause hose burst and leakage. Be sure to follow the specified minimum bending radius. ● Avoid excessive vibration The usage excessive vibration may cause leakage and hose coupling blow-off by fatigue. ● Avoid the usage exceeding applicable temperature The usage exceeding applicable temperature may cause leakage and hose coupling blow-off.
Caution
Personal injury or property damage may result if these instructions are not followed
● Avoid vacuum pressure (except for suction hose) Excessive vacuum pressure may result in the inner tube damage which leads to hose failure. in water or any other liquid. ● Avoid submerging hose assemblies in Hose assemblies submerged in water are exposed to external pressure which will reduce the service life of a hose and/or have bad effect on hose assembly performance. ●Remove all air from hydraulic hose assemblies. Air may cause damage to the inner tube which which will lead to hose failure. ●Follow minimum hose exposed length Follow minimum hose exposed length. Improper length may reult in inferior performance to catalog specification. ●Never repair or rework a hose assembly. Old or used hose assemblies do not have the same physical characteristics as a new hose and cannot be used. Old hoses or damaged hoses should be replaced with new one, and should not be repaired or reworked. ●Do not use for food or drinking water, since the hose is intended for industrial use.
2 Warranty period Warranty period is impulse cycle number or each specified period, whichever comes earlier (Refer to pages 7 to 10).
3 Preventive maintenance Before use, check for the following conditions. If any are found, replace with a new part. Physical damage, blister, exposed reinforcement, kinking, hose coupling blow-off, leakage etc. JIS B8360,8362,8364 recommend that hoses should be changed every 2 years.
4 Storage - Cap the couplings or hose cut ends - Keep out of direct sunlight - Do not expose to corrosive gas, oil or chemicals - Store in dark and dry place at the temperature between -10℃℃and +40℃(14° F to 104° F )
2
Symbols This catalog shows the product specifications in the format below so you can select the correct product for your needs and prevent the risk of danger.
Hoses are flexible tubes designed to carry fluid from one location to another or to
Hose
convey pressure. Typically, they include rubber hoses ( etc.) and resin hoses (
[Example Specifications of Hoses]
Temperature Range : ambient
Temperature Range: fluid
Permissible temperatures of ambient environment for the hose
Permissible temperatures of fluid flowing through the hose
Compatible Fluid Fluid applicable to the hose
Inner part of the hose, which comes into direct contact with the fluid The specifications show the materials for this part.
●Compatible Fluid / Mineral Hydraulic Oil ●Temperature Range: fluid / −40°C to 100°C / −40°F to 212°F ●Temperature Range: ambient / −40°C to 70°C / −40°F to 158°F ●Inner Tube / Oil-resistant synthetic rubber ●Outer Cover / Weather-resistant synthetic rubber
Pressure Outer Cover Outer part of the hose, which is intended to protect its reinforcing The specifications show the materials for this part.
Catalog Number When ordering a product, specify its catalog number.
Weight
*The color of this cover is black unless otherwise specified.
*For details, refer to page 5.
,
,etc.).
Inner Tube
Pressure shown in psi/MPa units
,
Approximate Weight of Hose
PA01 Maximum Working Pressure
1.5MPa 500PSI
Catalog Number
PA0104* PA0106* PA0108*
I.D. inch
1/4 3/8 1/2
O.D.
Max.W.P. MPa
mm
inch
mm
psi
6.3 9.5 12.7
0.55 0.69 0.83
14.0 17.4 21.2
200
1.5
Min.B.P. MPa
psi
870
6.0
Min.B.R. mm
inch
2.17 2.56 3.54
55 65 90
Weight g /m
l bs /f t
0.33 0.53 0.62
150 240 280
Reinforcement
4C
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
AS/27
AS/27 UL/30
I.D・O.D
Coupling Series
Inner and outer diameters of the hose
Series of couplings that are crimped either at a factory or with UNICRIMP. The number after “/” indicates the number of the page that describes the applicable series of couplings. *Crimping the couplings may be impossible depending on the type of UNICRIMP used.
Max.W.P. Maximum usable working pressure
Min.B.R. Minimum bending radius that can be achieved without performance degradation. This radius is specified on the inside surface of the bend area.
Min.B.P. Pressure that the hose should withstand without problems such as coupling detachment, hose bursting, and fluid leaking from the crimped part when the hose is subjected to water or oil pressure.
Reinforcement Fibers or wires woven or spirally wrapped around an inner tube to maintain hose p e rf o rm a nc e . T h e s p e c i f i c a t i on s s h o w t h e structure of the reinforcing.
3
Symbols
Couplings for connecting the hose to equipment. Usually, a crimping machine is
Couplings
used to crimp the couplings onto the hose.
[Example Specifications of Couplings] Catalog Number When ordering a product, specify its catalog number.
Type of End-configuration.
R
R
*For details, refer to page 5.
Catalog Number
Y(HEX)
A (L) Male British Tapered Pipe Thread(BSPT)
UZ04R UB06R UB08R UZ08R UB1012R UB12R UB16R UZ20R
Y Thread 1/4 3/8 1/2 1/2 3/4 3/4 1 1 1/4
inch
0.67 0.75 0.87 0.87 1.18 1.18 1.42 1.81
(L)
A
mm
17 19 22 22 30 30 36 46
inch
mm
0.51 0.59 0.71 0.71 0.79 0.79 0.87 0.99
13 15 18 18 20 20 22 25.2
inch
1.97 2.28 2.52 2.52 3.07 3.35 3.66 4.80
Weight
mm
lbs
50 58 64 64 78 85 93 122
0.11 0.19 0.28 0.28 0.49 0.63 0.95 1.91
g
50 85 125 125 220 285 430 865
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
Shape of Crimped Couplings
Surface Treatment of Standard Products
This figure shows a coupling before crimping. The shape of crimped couplings varies depending on the crimping machine used.
The specifications show the treatment method used to prevent metal fittings from becoming rusted.
Combinations of Hoses and Couplings The combinations of hoses and couplings comply with JIS B 8363 (End fittings for hydraulic hose assemblies). For assured quality, be sure to properly tighten the couplings using the torques shown on page 82.
■Applicable working Pressure of each thread (JIS B 8363) Size Thread
02
04 41.0
R
05
06
10
12
16
20
24
32
34.5
-
20.5
G、 C、 F、 F2
-
Q2
-
S、 SR(SAE standard)
-
-
-
-
H、 HR(SAE H.P)
-
-
-
-
34.5
K, K1~K7 (21MPa flange)
-
-
-
-
20.5
34.5
27.5
20.5
41.5
Accurate Tightening Torque(page 63) is required to achieve the above pressure.
4
08
Unit : MPa(psi)
17.0 34.5
34.5
24.5
10.5 27.5
- 20.5
How to Order ■Below are examples of the catalog numbers shown in this catalog. HOSE
Example of hose catalog numbers
(Pressure-rated hose)
(SAE hose)
PA 07 04
R1T 08
Hose inside diameter in 1/16 of an inch.(04=4/16=1/4 inch)
Hose inside diameter in 1/16 of an inch.(08=8/16=1/2 inch)
Recommended working pressure(07=7.0MPa)
Type of hose (hose series No.)
Type of hose (hose series No.)
COUPLING
UB 08
R
Coupling Series.
Type of thread. Hose inside diameter connected to couplings and thread size in 1/16 of an inch. (08 = 8/16 = 1/2inch) ・In case of jump size coupling. For Example, if hose ID is 5/8”(=10/16”) and thread size is 3/4”(=12/16”), UA1012R is the catalog number.
Thread
Crimping Portion (coupling series)
Adaptor
80 01 Adaptor
RG 08
Type of adaptor
【HOSE LENGTH(L)】
Combination of thread type In this case“R” & “G”
Thread size (08=8/16"=1/2")
【Orientation Angle】
Please refer to the figures below when you specify the assembly length.
L
L
L
225° NEAR END
Bent tube ends and flange head couplings can be oriented at different angles to one another and must be specified when ordering. As per the illustration right, the orientation angle is measured starting from either end as the far end, clockwise to the near end. In the case of illustration right, the orientation angle is 225 °. FAR END
L
Selecting the proper hose Please check below points. Fluid to be used. Delivery (flow rate and velocity) or Hose ID (Please refer “Pressure Loss”in this catalog) Maximum working pressure. Fluid and ambient Temperature. Thread type.
[Hose Length(L)]above and Hose Length (Please refer “Hose exposed length calculation”in this catalog) Orientation angle (Please refer above [Orientation Angle]) Application and Environmental Conditions. Minimum bending Radius. Drawing.
Ordering Method ① To order assembled hoses, specify the following (typical examples of data): Hose catalog No.
× Hose
②To order hoses and fittings separately, specify the following: Hose catalog No.
length
PA2108
×1,000(L)
Coupling at one end
Coupling at the other end
Hose adapter
No.
UZ08R
UZ08C
8002RG08
10
PA2108
× Hose
length
(L)
×60,000
Fittings catalog No.
No. of pieces
UZ08R UZ08R 8002RG08
10 10 10
or
Hose catalog No. PA2108
× Hose
length
(L)
×30,000
No. 2
5
Thread Identification ●The coupling threads shown below are available. They comply with the JIS and ISO standards. The types of coupling threads are designated “R,” “F,” etc. These are included in the catalog numbers.
● A series of coupli ngs is availab le for each hose. The standard coupli ng threads differ for each series of coupli ngs. For details , refer to the coupling specifications.
●Standard products are made from SS or SC equivalent steel processed with a surface treatment (zinc plating or chromate treatment). Products made from stainless steel or brass are also available. For details, contact us.
R
C
Male British Tapered Pipe Thread(BSPT)
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
C F
PF
R
G
Female Japanese Industrial Pipe Thread (JIS) Female 30°Seat
Male British Parallel Pipe Thread(BSPP)
PF
PF
30゜
30゜
30゜
CR9
Female Parallel Pipe Thread 90º (Male 30º Seat )
S/H
K
Flange Head S : CODE 61 Flange / H : CODE 62 Flange
JIS 20.5Mpa Flange
Q2
Female O-Ring Face Seal
UNF 90゜
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
30゜ Bend types such as CR4 ( 45º ) and CR6 ( 60º ) are also available.
Q2C7
Bend types such as Q2R4 (45º) are also available.
Bend types such as SR4 (45º) and HR4 (45º) are also available.
Female O-Ring Face Seal
F2
JIC 37° Female
UNF 37゜
Bend types such as Q2R9 (90º) are also available.
Bend types such as F2R4 (45º) and F2R9 (90º) are also available.
●The following non-standard products are also available. For details, contact us.
R1
J2
NPTF Male
A1
JIC 37° Male
NPTF
Rigid Male O-Ring Boss
UNF
A9
Male O-ring Face Seal
UNF
C1
Female NPSM Male 30° Seat
NPSM
UNF
37゜ 30゜ O-Ring Groove ※American
D
Female Taper Pipe Thread
Rc
D1
O-Ring Groove
For paint sprays
Pipe Thread
Female Taper Pipe Thread
F3
F4
SAE 45° Female
NPTF
Female Metric Thread Female 30°Seat
UNF
J3
SAE 45° Male
UNF
M(P=1.5)
45°
30゜ 45°
※Komatsu
CE9
Female Taper Pipe Thread
MQ4
DIN Metric Female Thread (with Male 12º Seat O-ring Groove)
M
D
D
12° φ
12° φ X
G
DIN Metric Female Thread (with Male 12º Seat O-ring Groove)
M
NPTF
30°
MQ5
Y (L)
Bend types such as MQ4R4 (45º) and MQ4R9 (90º) are available.
X
Y (L)
Bend types such as MQ5R4 (45º) and MQ5R9 (90º) are available.
* Coupling materials are carbon steel with zinc plating * As for PrimoLine series, coupling type is special one. Please see PrimoLine page (page 59).
6
Female 30°Seat
Hose Summary HOSE Series Inner Diameter
Lowpressure rubber hoses
Standard Rubber Hoses
Slim Rubber Hoses
OKE
mm Code Type OKE PA01 PA03 PA07 PA10 PA14 PA17 PA21 PA28 PA35 PF07 PF14 PF17 PF21 PFW PFH M 1/8 3.2 02 a 3/16 4.8 03 x i m 3.5 7.0 10.5 14.0 17.0 20.5 27.5 34.5 7.0 14.0 17.0 20.5 24.5 27.5 1/4 6.3 04 1.5 1.5 u 5/16 7.9 05 m 7.0 14.0 17.0 20.5 24.5 27.5 3/8 9.5 06 1.5 1.5 3.5 7.0 10.5 14.0 17.0 20.5 27.5 34.5 w o 7.0 14.0 17.0 20.5 24.5 27.5 1/2 12.7 08 1.5 1.5 3.5 7.0 10.5 14.0 17.0 20.5 27.5 34.5 r k 27.5 34.5 20.5 5/8 15.9 10 3.5 7.0 10.5 14.0 17.0 20.5 1.5 i n 20.5 3.5 7.0 10.5 14.0 17.0 20.5 27.5 34.5 3/4 19.0 12 1.5 g p 7/8 22.2 14 r e 7.0 10.5 14.0 17.0 20.5 27.5 34.5 20.5 1 25.4 16 1.5 3.5 s s 20.5 27.5 34.5 1-1/4 31.8 20 3.5 7.0 10.5 14.0 u r 20.5 27.5 34.5 1-1/2 38.1 24 3.5 7.0 10.5 14.0 e M 2 50.8 32 7.0 10.5 14.0 20.5 27.5 34.5 P 2-1/2 63.5 40 a inch
3
76.2
48
Relevant page
12~14
12
Minimum burst pressure (MPa)
15
3×
4× Maximum working pressure
−40 to − 40 t o+100(oil) +100 (oil), 0 to +50(water) −40 to+100 −40 to+60 −40 to +60(water-glycol) (water-glycol) −40 to Recommended −40 to +70 (oil) +70 (oil), 0 to +70 (water) ambient temperature −40 to +70 −40 to+60 −40 to +60(water-glycol) (ºC) (water-glycol) Mineral hydraulic Mineral hydraulic oil, Mineral Compatible fluid oil, water, water-glycol hydraulic oil water-glycol
Fluid temperature (ºC)
Uses and features Period
Warranty period
No. of times used
Lowpressure, lightweight
−40 to+100
−40 to +70
Mineral hydraulic oil
Abrasion-resistant slim type for ordinary hydraulic piping
Ordinary hydraulic piping
1 year for oil hoses or 6 months for water hoses
1 year
200,000
400,000
*Warranty is effective until the predetermined usage period expires or the impulse cycle count reaches the predetermined value, whichever occurs first. (The impulse cycle count refers to the number of times the hose has been pressurized under the specified hose usage conditions.)
*For information about other couplings, contact us. For information about adapters, refer to pages 64 and 65.
COUPLING
C o u p l i n g t h r e a d t y p e
Hose type Relevant page R F C G CR S SR H HR K~K4 K~K3R F4 F2 F2R Q Q2 Q2R
OKE PA01 PA03 PA07 PA10 PA14 PA17 PA21 PA28 PA35 PF07 PF14 PF17 PF21 PFW PFH 27 29 ~
● ● ● ● ● ● ●
34~39
34~44
27~33
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ●
● ● ● ● ●
● ● ● ● ●
● ● ● ● ●
● ● ●
● ●
● ●
● ●
● ●
● ●
● ● ●
● ● ●
● ● ●
● ● ● ● ●
● ●
● ●
● ●
● ●
● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ●
● ● ● ● ●
● ● ● ● ●
● ● ● ● ●
● ● ● ● ●
● ● ● ● ●
● ● ● ● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ● ● ● ● ● ● ● ●
7
Hose Summary HOSE Series Inner Diameter inch
●Hose Available Only
Slim Rubber Hoses 120°C Rubber Hoses HQ CQ SQ
SAE / DIN Hoses SAE Series
DIN Series
mm Code Type HQ35 C Q S Q2 8 EQ17 EQ21 EQ25 EQ28 EQ31 R1AT R2AT R12A R13A R15A 4SP 4SH M 02 a 03 x i m 36.0 22.5 40.0 04 u 05 m 42.0 44.5 06 36.0 18.0 33.0 28.0 w o 42.0 41.5 08 34.5 36.0 27.5 17.0 20.5 24.5 27.5 31.0 16.0 27.5 28.0 r k 35.0 10 34.5 36.0 27.5 20.5 24.5 27.5 31.0 13.0 25.0 28.0 17.0 i n 12 34.5 38.0 27.5 17.0 20.5 24.5 27.5 31.0 10.5 21.5 28.0 35.0 42.0 35.0 42.0 g p 14 r e 34.5 38.0 8.7 16.5 28.0 35.0 42.0 28.0 38.0 16 17.0 20.5 24.5 27.5 31.0 s s 6.2 12.5 21.0 35.0 42.0 21.0 32.5 20 34.5 38.0 17.0 20.5 24.5 27.5 31.0 u r 24 17.0 20.5 24.5 27.5 31.0 5.0 9.0 17.5 35.0 42.0 18.5 29.0 e M 25.0 32 20.5 31.0 4.0 8.0 17.5 35.0 P 40 a
1/8 3.2 3/16 4.8 1/4 6.3 5/16 7.9 3/8 9.5 1/2 12.7 5/8 15.9 3/4 19.0 7/8 22.2 1 25.4 1-1/4 31.8 1-1/2 38.1 2 50.8 2-1/2 63.5 3 76.2
48
Relevant page
16
17~18
Minimum burst pressure 4× max.working 5× Maximum working pressure pressure (MPa)
19~20
−
Fluid temperature (ºC)
-40 to +100 (-40 to +120(CQ38))
-40 to +120
Recommended ambient temperature (ºC)
-40 to +70
-40 to +70
Compatible fluid
Mineral hydraulic oil
Mineral hydraulic oil
−
Uses and features
Impulse Ultra MSHA High cycle Approved Abrasion 1,200,000
Maximum fluid temperature 120°C
−
1 year
1 year
−
1,000,000
−
Warranty period
Period No. of
times used 1,200,000 1,000,000 400,000
−
−
*Warranty is effective until the predetermined usage period expires or the impulse cycle count reaches the predetermined value, whichever occurs first. (The impulse cycle count refers to the number of times the hose has been pressurized under the specified hose usage conditions.)
COUPLING
C o u p l i n g t h r e a d t y p e
8
Hose type Relevant page R F C G CR S SR H HR K~K4 K~K3R F4 F2 F2R Q Q2 Q2R
*For information about other couplings, contact us. For information about adapters, refer to pages 64 and 65.
H Q3 5 C Q S Q2 8 EQ17 EQ21 EQ25 EQ28 EQ31 R1AT R2AT R12A R13A R15A 4SP 34~39 27~33 ● ● ー ● ● ● ● ● ● ● ー ● ● ● ● ● ● ● ー ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ー ● ● ● ● ● ● ー ● ● ● ● ー ● ● ● ● ● ー ● ● ● ● ● ● ー ● ● ● ● ● ● ● ー ● ● ● ● ● ー ● ● ● ● ー ● ● ● ● ● ● ● ー ● ● ● ー ● ● ● ● ● ● ー ● ● ● ● ー ● ー ● ● ● ● ● ● ● ● ● ● ● ● ● ● ー
4SH
HOSE Series Inner Diameter
JW・JWK VW
inch
mm Code Type M 1/8 3.2 02 a 3/16 4.8 03 x i m 1/4 6.3 04 u 5/16 7.9 05 m 3/8 9.5 06 w o 1/2 12.7 08 r k 5/8 15.9 10 i n 3/4 19.0 12 g p 7/8 22.2 14 r e 1 25.4 16 s s 1-1/4 31.8 20 u r 1-1/2 38.1 24 e M 2 50.8 32 P 2-1/2 63.5 40 a
3
76.2
Rubber Rubber Hoses Hoses Heat/ Large-bore Hoses Hoses for Air Suction Push-on Hoses both water-glycol high-pressure (lightweight,flexible) for steam oil-resistant for hot Hoses Hoses Hoses for Jacks for water cleaning cleaning Hoses Hoses cleaning and mineral oil WA・WAR
JW70 JWK
V W WA14 WAR
68.5 137.0
14.0
20.5
68.5 68.5
14.0 14.0
20.5 20.5
98.0 98.0
SA HM SA
HM
ACT
WH
PA03 -DA
ACT WH21 WE21 WE28 PA03-DA JBT
2.0 2.0 2.0
2.0
3.0 3.0 3.0 3.0
WE
20.5
20.5
27.5
3.5
20.5 20.5
27.5 27.5
3.5 3.5
2.0
7.0
20.5
27.5
3.5
2.0
7.0
20.5 20.5 20.5 20.5
27.5 27.5 27.5 27.5
3.5
4.9 3.0
48
Relevant page
21
22
23
24
About 2× 4× max. About 2.5× 6× max. 4× max. 5× max. 3× max. Minimum burst pressure maximum working max. working working working working (MPa) working pressure pressure working pressure pressure pressure pressure pressure −40
Fluid temperature (ºC)
-40 to +100
Recommended ambient temperature (ºC)
-40 to +70
Compatible fluid
Mineral hydraulic oil
Uses and features
Warranty period
For ultra high pressure hydraulic tools
No. of
−0.08665MPa
1 year
Period
times used
Max. negative pressure
25,000
0 to +80
JBS
14.0 10.5 26
20.5 17.0
About 4× max. working pressure
to
-40 to +100
−40 to to +70(oil ), -40 to -40 to +60 -40 to (water-glycol), +100 0 to+70 +70 +60 -40 to +70 (oil) (water)
-40
Mineral Mineral Hot Water-glycol hydraulicoil/ Steam mineral hydraulic water and mineral hydraulic oil engine oil oil/water
Air
-40 to +70
Mineral hydraulic oil
Large bore, large Cleaning/ Steam Heat Crimping Hot Injection Air flow volume, max. machine cleaning green cut/ cleaning resistance steel plants supply not required length of 40m peeling 6 months
200,000
4× max. working pressure
-40 to +60 +4 to -40 to +93(oil), 0 to -40 to (water-glycol), 0 to+50 +210 +135 +120 +60 (water) -40 to +100 (oil)
-40 to +70
Water
25
JBF
100,000
3 months 1 year
−
400,000
1 year (oil)/ 6 months (water)
6 months
100,000
1 year
1 year
1 year
400,000
−
200,000
*Warranty is effective until the predetermined usage period expires or the impulse cycle count reaches the predetermined value, whichever occurs first. (The impulse cycle count refers to the number of times the hose has been pressurized under the specified hose usage conditions.)
*For information about other couplings, contact us. For information about adapters, refer to pages 64 and 65.
COUPLING
C o u p l i n g t h r e a d t y p e
Hose type Relevant page R F C G CR S SR H HR K~K4 K~K3R F4 F2 F2R Q Q2 Q2R
JW70 JWK
V W WA14 WAR
SA
HM
● ●
● ● ●
27~33 ●
●
●
●
● ● ● ● ● ● ●
● ● ● ●
● ● ● ●
●
● ● ●
ACT WH21 WE21 WE28 PA03-DA JBT 34~46 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
JBF
JBS
● ●
● ●
● ●
9
Hose Summary HOSE Series Inner Diameter inch
1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2 2-1/2 3
mm Code Type M 3.2 02 a 4.8 03 x i m 6.3 04 u 7.9 05 m 9.5 06 w o 12.7 08 r k 15.9 10 i n 19.0 12 g p 22.2 14 r e 25.4 16 s s 31.8 20 u r 38.1 24 e M 50.8 32 P 63.5 40 a
76.2
Ultra-High Standard Resin Hoses Special Application Resin Hoses Pressure Resin Hoses
KF
KG
KA
14.0 14.0
20.5 17.0 14.0
SPL
20.5 20.5
14.0 10.5
KB
19.5 15.0 14.5 12.0 10.5 10.5
25.5 22.0 20.5 17.0 16.0
5.0
9.5
9.0
For For For machine paint cleaning tools sprays
For jacks
For steam piping
AG10
JC70
SF
PS
WSH
SPL
KF
JAT
JAM
J AL
JKY
JAK
20.5 10.5
31.0 27.5 24.5
10.5 10.5
68.5 14.0
2.0
14.5
14.0
2.0 2.0 2.0
14.5 10.5
294.0 245.0 196.0 147.0 68.5 245.0 127.5 16.0 117.5 14.0 98.0 88.0 73.5
20.5
7.5
98.0 68.5 68.5 68.5
68.5
48
50~51
Relevant page
Minimum burst pressure (MPa)
4× max. working pressure
Fluid temperature (ºC)
−40 to +100
+40 to −20 to +93 +80
Recommended ambient temperature (ºC)
−40 to +70
−40 to −20 to +70 +40
Compatible fluid
Mineral hydraulic oil Ordinary hydraulic piping
Uses and features Flexible type
Warranty period
Small bending radius
No. of 150,000 200,000 times used
60~62
4× max. working pressure
About 2× max. working pressure
0 to +80
0 to +70
−40 to +70
+4 to +220
−40 to +70
−30 to −30 to +80 +100
−40 to +50 (oil), 0 to +50 (water)
−40 to +80
−30 to +70
−40 to +50 (oil), 0 to +50 (water)
−40 to +70
Water/mineral hydraulic oil
Mineral hydraulic oil
Mineral Organic Mineral Mineral Steam hydraulic oil hydraulic solvent Water hydraulic paint oil oil
Ordinary hydraulic piping
1 year
Period
54~56
51 4× max. About 3× max. 2× max. working 3× max. working working pressure working pressure pressure pressure
150,000
Machine tools,
Paint
Cleaning, Ultra high Steam
sprays, pressure shock hydraulic injury antistatic protection treatment absorption tools
1 year
6 months
150,000 25,000
−
Water jet devices, Crimping machine jacks, high-pressure piping cleaning tools not required
1 year 25,000 100,000
Jacks
1 year
150,000
5,0 00
10,000
15,00 0 100,00 0 200,000
*Warranty is effective until the predetermined usage period expires or the impulse cycle count reaches the predetermined value, whichever occurs first. (The impulse cycle count refers to the number of times the hose has been pressurized under the specified hose usage conditions.)
*For information about other couplings, contact us. For information about adapters, refer to pages 64 and 65.
COUPLING
C o u p l i n g t h r e a d t y p e
10
Hose type Relevant page R F C G CR S SR H HR K K2 K~K4 K~K3R F4 F2 F2R Q Q2 Q2R
KF
KG
SPL
KA
KB
AG10
PS
WSH
JC70
SF
27~33 ● ● ●
● ● ●
● ● ●
SPL
KF
JAT
JAM
JAL
JKY
JAK
●
●
●
●
●
34~46 ● ● ●
● ● ●
● ● ●
● ● ●
● ● ●
●
● ● ●
● ●
● ● ●
● ●
●
●
●
●
●
・
●
This catalog shows the series of UNICRIMP-crimped couplings for UC28. If you use other model, check the standards shown in your torque-tightening standard table. If you have any questions, contact us.
Hoses and Couplings
Hose catalog number
Se ri es
OKE
PA01
PA03
PA07
PA10
PA14
PA17
PA21
PA28
PA35
PF07 PF14 PF17
PF21
PFW PFH
S ize 04 06 08 10 12 16 04 06 08 04 06 08 10 12 16 20 24 04 06 08 10 12 16 20 24 32 04 06 08 10 12 16 20 24 32 04 06 08 10 12 16 20 24 32 04 06 08 10 12 16 04 06 08 10 12 16 20 24 32 04 06 08 10 12 16 20 24 32 04 06 08 10 12 16 20 24 32 04 06 08 04 06 08 04 06 08 04 06 08 10 12 16 04 06 08 04 06 08
Applicable coupling series Factor UNICRIMP -crimped -crimped LS
AS
S er ie s
LS
UT AS/UL
CQ36 AS
UT LC UZ UB UZ
AS/UL
CQ38
UL UT LC UZ
SQ28
EQ17 UB
UB UZ
UZ
HW
HW
UZ UB UZ
UZ
EQ21
UB UB UZ
UZ
HW
HW
UZ UB UZ
EQ25
UZ
UB UB UZ
UZ
HW
HW
UZ UB UZ
UZ
EQ28
EQ31
UB UB UZ UB UZ
UB
UZ
HW
HW
UZ
UZ
UB
UB
UZ KN KD UZ
UZ
08 10 12 16 20 24 08 10 12 16 20 24 32 08 10 12 16 20 24 08 10 12 16 20 24 08 10 12 16 20 24 32
Factor -crimped
UNICRIMP -crimped
UB
UB
UB UZ
KG
UB
UB
S er ies KF
UB UZ UZ
SPL
UB(C X) ー
UB
ー
UB
KA
UZ UB
UB UZ HW UZ
UZ HW
KB
UB
UB UZ HW KN
UZ HW -
UB
UB
UZ KN
UZ -
S er ies AG10 PS
UB
UB
WSH JC70
UZ KN EX
-
S er ies JW70 JWK
VW
UZ
UB
WAR UZ -
SA
UL/UZ UB UL/UZ UB UZ
HM ACT WH21
UB UZ
WE21 UB
UB
- UZ UB
04 06 08 12 06 08 03 04 06 08 02 03 04 05 06 08 12 03 04 05 06 08 12 16
Factor -crimped
UNICRIMP -crimped
JY SY SY UX SY CG JG
SY
SG
SG SY CY JY SY
CY JY
SY
SY CY SY/UL - SY/UL UX CY SY/UL - SY/UL UX
Applicable coupling series
Hose catalog number
UZ -
KN
S ize
Special Application Resin Hoses
UB
UB
Applicable coupling series
Hose catalog number
-
SF
S ize
04 06 08 03 04 05 04 06 03 04 06 08 10
Factor -crimped
UNICRIMP -crimped
JG SG CY JY SY JY UY CW JG SG SH
SG
- SY UY - SG SH -
Special Application Rubber Hoses
WA14
UZ UB UZ UZ UB UZ
08 10 12 16 20 04 06 08 10 12 16 20 08 10 12
Hose catalog number
UZ
KN EX UZ UB UZ UZ UB UZ UZ UB UZ UZ UB UZ
Si ze
UZ
UB
UB
Applicable coupling series
Hose catalog number
HQ35 UT
Standard Resin Hoses
High Durable Rubber Hoses
Standard Pressure Rubber Hoses
WE28
PA03-DA
JBT JBF JBS
S ize 04 06 08 04 06 08 16 20 24 32 04 06 08 04 06 08 08 12 16 12 16 04 06 08 06 04 06 08 12 16 20 24 32 04 06 08 12 16 20 24 32 04 06 08 12 16 40 48 40 48 40 48
Applicable coupling series Factory UNICRIMP Push-on -crimped -crimped hoses ZP KH UB
ZP - UB
-
EK
-
-
UT
UT
LC HW
LC HW
UL
UL
-
UL
UL
-
SK
ー
- -
ー
ー
AT
UF UZ UB UZ GB
GA(U L) UZ
-
UB
S ize
JAT
03 03 05 03 04 05 06 08 10 12 16 04 04 05 06 08
JAM
JKY JAK
Factor -crimped
UNICRIMP -crimped
BN
-
BX
-
BL BK AK
-
AL UY AK BK
- -
AK
-
UZ
KN
-
UZ UB UZ
UZ UB
GB UB KN KD
S er ies
JAL
ー
Applicable coupling series
Hose catalog number
-
UN
UB
Ultra-High Pressure Resin Hoses
ー ー
AS UL
ー
EC
ー
ー
DX
ー
ー
EX
ー
ー
UT
11
● ● ● ●
Compatible Fluid / Mineral Oil, Water Inner Tube / Oil Resistant Synthetic Rubber Outer Cover / Weather Resistant Synthetic Rubber Temperature Range: fluid / −40℃ to 100℃(Oil) / 0℃ t o 50℃(Water) −40℉ to 212℉(Oil) / 32℉ to 122℉(Water) ● Temperature Range : ambient /−40℃ to 70℃(−40℉ to 158℉)
OKE Series For Low Pressure
OKE Maximum Working Pressure
1.5MPa 200PSI
Catalog Number
I.D. inch
OKE04 OKE06 OKE08 OKE10 OKE12 OKE16
1/4 3/8 1/2 5/8 3/4 1
mm
O.D. inch mm
6.6 9.7 13.0 16.2 19.3 25.7
0.50 0.63 0.78 0.93 1.09 1.44
12.7 15.9 19.8 23.5 27.7 36.5
Max.W.P. psi MPa
1.5
200
Min.B.P. psi MPa
600
4.5
Min.B.R. inch mm
2.56 2.95 3.94 4.92 5.91 7.87
65 75 100 125 150 200
Weight l bs /f t g/ m
0.09 0.12 0.16 0.21 0.29 0.48
130 170 240 310 430 720
Reinforcement
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
LS/27
LS/27
UT/27
UT/27
2C
4C
*These hoses cannot be used under surge (shock) pressure. If the hose will be subjected to surge (shock) pressure, replace it with a PASCALART hose (PA). *Hoses suitable for use at high temperatures (120°C and 150°C) are also available. For details, refer to the Lace-up Rubber Hose Catalog. We recommend using water-glycol with couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). Warning
Do not use high water base fluid (HWBF) with the hoses listed above. Doing so could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
■JIS Standard ・JIS K6349-3(high-pressure rubber hose) ・JIS B8360(high-pressure rubber hose assembly)
1
●Compatible Fluid Mineral Oil
LONGER HOSE LIFE
PASCALART series hose provides a longer service life and a greater fatigue resistance than conventional hose. PASCALART series hose guarantees a service life of 400,000 impulse cycles conforming to JIS heavy duty application standard B8360. Conventional hose assures a service life of only 100,000 to 200,000 impulse cycles.
●Inner Tube Oil Resistant Synthetic Rubber
●Outer Cover Weather Resistant Synthetic Rubber
●Temperature Range : fluid
15%
■Hose Life Comparison
-40℃to +100℃ (-40° F to +212° F)
5% Test pressure ±5%
400,000 impulse cycles (JIS waveform)
●Temperature Range : ambient
200,000 impulse cycles (SAE waveform)
SAE100R2
-40℃to +70℃ (-40° F to +158° F)
150,000 impulse cycles (SAE waveform)
SAE100R1
1.0MPa 0MPa
5% 50%
50% 1cycle
2
SMALLER BENDING RADIUS
PASCALART series hose minimum bending radius is 2/3 of the JIS K6349 standard, which results in shorter hydraulic hose assemblies, and more compact hydraulic circuits. PASCALART hose
3
Conventional highpressure rubber hose
BROAD RANGE
PASCALART series hose is classified into 9 different work ing pressure categories. This broad range of working pressures, makes it easy to select the right hose for any given hydraulic circuit pressure.
PA01 Maximum Working Pressure
1.5MPa 200PSI
Catalog Number
PA0104* PA0106* PA0108*
I.D. inch
1/4 3/8 1/2
mm
O.D. inch mm
Max.W.P. psi MPa
Min.B.P. psi MPa
Min.B.R. inch mm
6.3 9.5 12.7
0.55 0.69 0.83
200
870
2.17 2.56 3.54
14.0 17.4 21.2
1.5
6.0
55 65 90
Weight l bs /f t g/ m
0.33 0.53 0.62
150 240 280
Reinforcement
4C
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
AS/27
AS/27 UL/30
We recommend using water-glycol with couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). *For factory-assembled hoses with stainless steel fittings, select the UL series hoses.
Warning Do not use high water base fluid (HWBF) with the hoses listed above. Doing so could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
Reinforcing
12
PA series PA03 Maximum Working Pressure
3.5MPa 500PSI
Catalog Number
PA0304* PA0306* PA0308* PA0310 PA0312 PA0316 PA0320 PA0324
inch
I.D. mm
O.D. inch mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1
0.55 0.69 0.83 0.93 1.24 1.48 1.64 1.90
14.0 17.4 21.2 23.5 31.4 37.5 41.7 48.3
Max.W.P. psi MPa
500
Min.B.P. psi MPa
3.5 2,000
14.0
Min.B.R. inch mm
2.17 2.56 3.54 4.33 5.31 6.69 7.87 9.84
55 65 90 110 135 170 200 250
Weight l bs /f t g/ m
0.10 170 0.14 220 0.19 290 0.20 310 0.39 620 0.49 800 0.77 950 0.90 1,170
Reinforcement
4C
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
AS/27
AS/27 UL/230
UT/27
UL/30
LC/27
UT/27 LC/27
2C 4C 1W
We recommend using water-glycol with couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). *Factory-assembled hoses with stainless steel fittings are the UL series hoses. Do not use high water base fluid (HWBF) with the hoses listed above. Do not use water-glycol with either PA0320 or PA0324. Failure to observe these Warning instructions could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
PA07 Maximum Working Pressure
7.0MPa 1,000PSI
Catalog Number
PA0704* PA0706* PA0708* PA0710* PA0712* PA0716* PA0720 PA0724 PA0732
I.D.
O.D.
Max.W.P. MPa
inch
mm
inch
mm
psi
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.53 0.66 0.76 0.94 1.05 1.32 1.71 1.98 2.49
13.5 16.7 19.4 23.8 26.6 1,000 33.5 43.5 50.2 63.2
Min.B.P. MPa
psi
7.0 4,000
Min.B.R. mm
inch
2.17 2.95 3.15 4.33 28.0 5.12 6.89 8.66 10.63 13.78
55 75 80 110 130 175 220 270 350
Weight g/ m
l bs /f t
0.15 220 0.22 330 0.25 380 0.34 510 0.40 600 0.57 850 1.07 1,610 1.27 1,910 1.66 2,490
Reinforcement
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
UZ/34
UB/34 UB/34
2W
UZ/34
UZ/34
HW/41
HW/41
We recommend using water-glycol with couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). *Factory-assembled hoses with stainless steel fittings are the UL and UX series hoses. Do not use high water base fluid (HWBF) with the hoses listed above. Do not use water-glycol with either PA0720 or PA0724 or PA0732. Failure to observe Warning these instructions could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
PA10 Maximum Working Pressure
10.5MPa 1,500PSI
Catalog Number
PA1004* PA1006* PA1008* PA1010* PA1012* PA1016* PA1020 PA1024 PA1032
inch
I.D. mm
O.D. inch mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.53 0.66 0.76 0.94 1.05 1.32 1.71 1.98 2.60
Max.W.P. psi MPa
13.5 16.7 19.4 23.8 26.6 1,500 33.5 43.5 50.2 66.0
Min.B.P. psi MPa
10.5 6,000
Min.B.R. inch mm
2.17 2.95 3.15 4.33 42.0 5.12 6.89 8.66 10.63 14.57
55 75 80 110 130 175 220 270 370
Weight l bs /f t g/ m
0.15 230 0.23 340 0.26 390 0.35 530 0.41 610 0.57 860 1.07 1,610 1.27 1,910 2.77 4,150
Reinforcement
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
UZ/34
UB/34 UB/34
2W 4S
UZ/34
UZ/34
HW/41
HW/41
We recommend using water-glycol with couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). *Factory-assembled hoses with stainless steel fittings are the UL and UX series hoses. Do not use high water base fluid (HWBF) with the hoses listed above. Do not use water-glycol with PA1020, PA1024, or PA1032. Failure to observe these Warning instructions could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
PA14 Maximum Working Pressure
14.0MPa 2,000PSI
Catalog Number
PA1404* PA1406* PA1408* PA1410* PA1412* PA1416* PA1420 PA1424 PA1432
inch
I.D. mm
O.D. inch mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.53 0.66 0.76 1.00 1.15 1.41 1.71 2.07 2.60
Max.W.P. psi MPa
13.5 16.7 19.4 25.4 29.3 2,000 35.8 43.5 52.7 66.0
Min.B.P. psi MPa
14.0 8,000
Min.B.R. inch mm
2.17 2.95 3.54 4.72 56.0 5.51 7.09 9.45 11.02 14.57
55 75 90 120 140 180 240 280 370
Weight l bs /f t g/ m
0.16 0.23 0.27 0.50 0.63 0.82 1.07 2.04 2.77
240 350 400 750 940 1,230 1,610 3,060 4,150
Reinforcement
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
UZ/34
UB/34 2W
4S
UB/34 UZ/34
UZ/34
HW/41
HW/41
We recommend using water-glycol with couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). *Factory-assembled hoses with stainless steel fittings are the UL and UX series hoses. Do not use high water base fluid (HWBF) with the hoses listed above. Do not use water-glycol with PA1420, PA1424, or PA1432, Failure to observe these Warning instructions could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
13
PA series PA17 Maximum Working Pressure
17.0MPa 2,500PSI
Catalog Number
PA1704* PA1706* PA1708 PA1710 PA1712 PA1716
I.D. inch
1/4 3/8 1/2 5/8 3/4 1
mm
O.D. inch mm
6.3 9.5 12.7 15.9 19.0 25.4
0.53 0.66 0.76 1.00 1.15 1.41
Max.W.P. psi MPa
13.5 16.7 19.4 2,500 25.4 29.3 35.8
Min.B.P. psi MPa
17.0 10,000
68.0
Min.B.R. inch mm
2.36 3.15 3.54 4.72 5.51 7.28
60 80 90 120 140 185
Weight l bs /f t g/ m
Reinforcement
0.16 240 0.24 360 0.28 420 0.51 770 0.63 950 0.87 1,300
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
1W
UZ/34 UB/34 UZ/34
2W
UB/34
UZ/34
UB/34
*For factory-assembled hoses with stainless steel fittings, select the UL series hoses.
PA21 Maximum Working Pressure
20.5MPa 3,000PSI
Catalog Number
PA2104 PA2106 PA2108 PA2110 PA2112 PA2116 PA2120 PA2124 PA2132
inch
I.D. mm
O.D. inch mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.53 0.71 0.87 1.00 1.15 1.41 1.78 2.07 2.60
inch
mm
O.D. inch mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.59 0.75 0.87 1.04 1.14 1.41 1.80 2.20 2.95
inch
mm
O.D. inch mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.59 0.75 0.87 1.04 1.14 1.44 1.93 2.20 2.95
Max.W.P. psi MPa
13.5 18.0 22.2 25.4 29.3 3,000 35.8 45.2 52.7 66.0
Min.B.P. psi MPa
20.5 12,000
Min.B.R. inch mm
2.76 3.54 4.33 5.51 82.0 6.69 8.27 10.24 12.20 16.93
70 90 110 140 170 210 260 310 430
Weight lb s/ ft g /m
0.17 0.31 0.43 0.51 0.64 0.87 1.57 2.04 2.77
Reinforcement
250 470 650 770 960 1,300 2,360 3,060 4,150
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
2W
UZ/34
UB/34 UB/34
4S
UZ/34
UZ/34
HW/40
HW/40
PA28 Maximum Working Pressure
27.5MPa 4,000PSI
Catalog Number
PA2804 PA2806 PA2808 PA2810 PA2812 PA2816 PA2820 PA2824 PA2832
I.D.
Max.W.P. psi MPa
15.1 19.1 22.2 26.4 29.0 4,000 35.9 45.6 55.9 75.0
Min.B.P. psi MPa
Min.B.R. inch mm
2.76 3.94 4.33 5.51 27.5 16,000 110.0 6.69 8.66 11.02 12.60 16.93
70 100 110 140 170 220 280 320 430
Weight lb s/ ft g /m
0.25 0.36 0.52 0.67 0.75 1.17 1.74 2.93 5.27
Reinforcement
380 540 780 1,000 1,130 1,750 2,610 4,390 7,900
2W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34
UZ/34
UB/34
UB/34
UZ/34 KN/41 KD/41
UZ/34
4S
6S
ー ー
PA35 Maximum Working Pressure
34.5MPa 5,000PSI
Reinforcing
Catalog Number
PA3504 PA3506 PA3508 PA3510 PA3512 PA3516 PA3520 PA3524 PA3532
14
I.D.
Max.W.P. psi MPa
15.1 19.1 22.2 26.4 29.0 5,000 36.6 49.0 55.9 75.0
Min.B.P. psi MPa
Min.B.R. inch mm
3.15 4.33 5.91 6.69 34.5 20,000 138.0 8.66 11.02 12.99 14.96 19.69
80 110 150 170 220 280 330 380 500
Weight lb s/ ft g /m
0.26 0.37 0.53 0.67 0.75 1.33 2.57 2.96 5.33
Reinforcement
390 550 800 1,000 1,130 2,000 3,850 4,440 8,000
2W
UZ/34
4S
UB/34
6S
KN/41 KD/41
UZ/34
UB/34
UZ/34
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
ー ー
PF series
● Compatible Fluid / Mineral Oil ● Inner Tube / Synthetic Rubber ● Outer Cover / Synthetic Rubber ● Temperature Range : fluid / −40℃ to + 100℃
Based on More flexible
−40℉ to + 212℉
● Temperature Range : ambient / −40℃ to +70℃
Smaller bending radius
−40 ℉ to +158℉
PF07 Maximum Working Pressure
7.0MPa 1,000PSI
Catalog Number
PF0704* PF0706* PF0708*
I.D. inch
1/4 3/8 1/2
mm
O.D. inch mm
6.3 9.5 12.7
0.47 0.61 0.73
Max.W.P. psi MPa
11.9 15.5 1,000 18.5
Min.B.P. psi MPa
7.0 4,000
28.0
Min.B.R. inch mm
1.57 1.97 2.56
40 50 65
Weight lb s/ ft g/ m
0.09 0.15 0.21
140 220 320
Reinforcement
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
UL/30 UZ/34 ・
UB/34
*For factory-assembled hoses with stainless steel fittings, select the UL series hoses.
PF14 Maximum Working Pressure
14.0MPa 2,000PSI
Catalog Number
PF1404* PF1406* PF1408*
I.D. inch
1/4 3/8 1/2
mm
O.D. inch mm
6.3 9.5 12.7
0.47 0.61 0.75
Max.W.P. psi MPa
11.9 15.5 2,000 19.0
Min.B.P. psi MPa
14.0 8,000
56.0
Min.B.R. inch mm
1.57 1.97 2.36
40 50 60
Weight lb s/ ft g/ m
0.10 0.15 0.23
150 230 350
Reinforcement
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
UL/30 UZ/34 ・
UB/34
*For factory-assembled hoses with stainless steel fittings, select the UL series hoses.
PF17 Maximum Working Pressure
17.0MPa 2,500PSI
Catalog Number
PF1704* PF1706* PF1708*
I.D. inch
1/4 3/8 1/2
mm
O.D. inch mm
6.3 9.5 12.7
0.50 0.66 0.80
Max.W.P. psi MPa
12.6 16.7 2,500 20.2
Min.B.P. psi MPa
17.0 10,000
68.0
Min.B.R. inch mm
1.77 2.36 3.15
45 60 80
Weight lb s/ ft g/ m
0.13 0.22 0.33
190 330 500
Reinforcement
1W 2W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
UZ/34 UB/34
*For factory-assembled hoses with stainless steel fittings, select the UL series hoses.
PF21 Maximum Working Pressure
20.5MPa 3,000PSI
Catalog Number
PF2104* PF2106 PF2108 PF2110 PF2112 PF2116
I.D. inch
1/4 3/8 1/2 5/8 3/4 1
mm
O.D. inch mm
6.3 9.5 12.7 15.9 19.0 25.4
0.50 0.68 0.80 0.98 1.13 1.41
Max.W.P. psi MPa
12.6 17.2 20.2 3,000 24.9 28.7 35.8
Min.B.P. psi MPa
20.5 12,000
82.0
Min.B.R. inch mm
1.97 2.56 3.35 3.94 4.72 7.09
50 65 85 100 120 190
Weight lb s/ ft g/ m
0.13 200 0.28 420 0.35 530 0.47 710 0.61 910 0.83 1,250
Reinforcement
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
2W
UZ/34
UB/34 UB/34
*For factory-assembled hoses with stainless steel fittings, select the UL series hoses.
PFW Maximum Working Pressure
24.5MPa 3,500PSI
Catalog Number
PFW04 PFW06 PFW08
I.D. inch
1/4 3/8 1/2
mm
O.D. inch mm
6.3 9.5 12.7
0.53 0.68 0.80
mm
O.D. inch mm
6.3 9.5 12.7
0.53 0.68 0.80
Max.W.P. psi MPa
13.4 17.2 3,500 20.2
Min.B.P. psi MPa
24.5 14,000
98.0
Min.B.R. inch mm
1.97 2.76 3.54
50 70 90
Weight lb s/ ft g/ m
0.19 0.29 0.36
290 430 540
Reinforcement
2W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
ー
PFH Maximum Working Pressure
27.5MPa 4,000PSI
Catalog Number
PFH04 PFH06 PFH08
I.D. inch
1/4 3/8 1/2
Max.W.P. psi MPa
13.4 17.2 4,000 20.2
Min.B.P. psi MPa
27.5 16,000 110.0
Min.B.R. inch mm
1.97 2.76 3.54
50 70 90
Weight lb s/ ft g/ m
0.20 0.30 0.37
300 450 550
Reinforcement
2W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
UZ/34 UB/34
15
● ● ● ● ●
HQ35 Series Impulse cycle 1,200,000
Compatible Fluid / Mineral Oil Inner Tube / Synthetic Rubber Outer Cover / Synthetic Rubber Temperature Range : fluid / -40℃ to 100℃(-40℉ to 212℉) Temperature Range : ambient / -40℃ t o 70℃(-40 ℉ to 158℉)
HQ35 Maximum Working Pressure
34.5MPa 5,000PSI
Catalog Number
HQ3508 HQ3510 HQ3512 HQ3516 HQ3520
inch
I.D. mm
O.D. inch mm
1/2 5/8 3/4 1 1-1/4
12.7 15.9 19.0 25.4 31.8
0.87 1.04 1.14 1.44 1.92
Max.W.P. psi MPa
22.2 26.4 29.0 5,000 36.6 48.7
Min.B.P. psi MPa
Min.B.R. inch mm
4.72 6.30 34.5 20,000 138.0 7.87 9.45 12.99
CQ Series Impulse cycle 1,000,000 MSHA Approved
120 160 200 240 330
Weight lb s/ ft g/ m
Reinforcement
0.50 750 0.66 990 0.72 1,080 1.30 1,950 2.49 3,730
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UB/34
UB/34
UB/34
UB/34 UZ/34
4S 6S
● ● ● ●
Compatible Fluid / Mineral Oil Inner Tube / Oil Resistant Synthetic Rubber Outer Cover / Weather Resistant Synthetic Rubber Temperature Range : fluid /-40℃ to +100℃(-40℉ to +212℉)(CQ36) fluid -40℃ to +120℃(-40℉ to +248℉)(CQ38) ● Temperature Range : ambient / -40℃ t o 70℃(-40 ℉ to 158℉)
CQ36/38 Maximum Working Pressure
36.0~38.0MPa
Catalog Number
CQ3604 CQ3606 CQ3608 CQ3610 CQ3812 CQ3816 CQ3820
5,200~5,500PSI
I.D.
O.D.
Max.W.P. MPa
inch
mm
inch
mm
psi
1/4 3/8 1/2 5/8 3/4 1 1-1/4
6.3 9.5 12.7 15.9 19.0 25.4 31.8
0.59 0.76 0.87 1.04 1.19 1.44 1.87
15.1 19.2 5,200 22.2 26.4 30.1 36.6 5,500 47.4
Min.B.P. MPa
psi
Min.B.R. mm
inch
3.15 4.33 36.0 20,800 144.0 5.51 5.91 8.27 38.0 22,000 152.0 10.24 12.99
80 110 140 150 210 260 330
Weight g/ m
Reinforcement
lb s/ ft
0.26 0.38 0.50 0.67 0.94 1.31 2.42
380 570 750 1000 1400 1950 3600
2W
4S
6S
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34
UZ/34
UB/34
UB/34
UB(CX)/34 UB/34
ー
● Compatible Fluid / Mineral Oil SQ28 Series ● Inner Tube / Oil Resistant Synthetic Rubber Weather Resistant Synthetic Rubber with Ultra High Abrasion resistant hose ● Outer Cover / Ultra High Molecular Weight Polyethylene ● Temperature Range : fluid / -40℃ to +100℃(-40℉ to +212℉) ● Temperature Range : ambient / -40℃ to +70℃(-40℉ to +158℉)
SQ28 Maximum Working Pressure
27.5MPa 4,000PSI
Reinforcing
Catalog Number
SQ2808 SQ2810 SQ2812
16
I.D. inch
1/2 5/8 3/4
mm
O.D. inch mm
12.7 15.9 19.0
0.89 1.05 1.15
Max.W.P. psi MPa
22.5 26.7 4,000 29.3
Min.B.P. psi MPa
27.5 16,000 110.0
Min.B.R. inch mm
4.72 5.91 7.09
120 150 180
Weight lb s/ ft g/ m
Reinforcement
0.52 770 0.68 1010 0.74 1100
4S
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UB/34
ー
1
EPOQU series hose can be used continuously with a hydraulic circuit oil temperature of 120℃(248° F). Conventional hose is only rated for 100℃(212° F)
●Compatible Fluid Mineral Oil ●Inner Tube Oil Resistant Synthetic Rubber
( 2 48 )
CONTINUOUS SERVICE AT 120
●Outer Cover Weather Resistant Synthetic Rubber
2
●Temperature Range : fluid -40℃ to +120℃ (-40℉ to +248℉)
EPOQU successfully passes 1,000,000 impulse cycles at 120 (250 ).
120℃ 100℃
JIS Standarts SAE Standard
LONGER HOSE LIFE
●Temperature Range : ambient -40℃ to +70℃ (-40℉ to +158℉)
15%
5%
Test pressure ±5%
1,000,000 cycles
SAE100R15
500,000 cycles
JIS K 6349-3
400,000 cycles
SAE 100R2
1.0MPa
200,000 cycles
5%
0MPa 50%
50% 1cycle
3
SMALLER BENDING RADIUS
EPOQU series hose minimum bending radius is 2/3 of the conventional standard, which results in shorter hydraulic hose assembly lengths, and more compact hydraulic circuits.
4
Conventional hose
EASY INSTALLATION
EPOQU is flexible. EPOQU requires just 2/3 of the force necessary to bend the conventional rubber hose to the same bending radius. Thus, EPOQU allows easy and speedy installation.
F Conventional highpressure hose F
5
F
F:Force(kg) to bend a hose
BROAD RANGE
EPOQU series is classified into 5 categories of different working pressure so that you can select a right hose according to the pressure rating of the pump to be applied.
EQ17 Maximum Working Pressure
17.0MPa 2,500PSI
Catalog Number
EQ1708 EQ1710 EQ1712 EQ1716 EQ1720 EQ1724
inch
I.D. mm
O.D. inch mm
1/2 5/8 3/4 1 1-1/4 1-1/2
12.7 15.9 19.0 25.4 31.8 38.1
0.87 1.03 1.15 1.39 1.80 2.07
Max.W.P. psi MPa
22.2 26.2 29.3 2,500 35.2 45.6 52.7
Min.B.P. psi MPa
17.0 12,500
Min.B.R. inch mm
3.54 4.33 5.51 85.0 6.30 8.27 11.02
90 110 140 160 210 280
Weight l bs /f t g /m
0.42 630 0.57 860 0.66 990 0.95 1,430 1.71 2,560 2.05 3,070
Reinforcement
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 2W UB/34 4S
UZ/34 HW/40
UB/34
UZ/34 HW/41
17
Epoqu series
EQ21 Maximum Working Pressure
20.5MPa 3,000PSI
Catalog Number
EQ2108 EQ2110 EQ2112 EQ2116 EQ2120 EQ2124 EQ2132
inch
I.D. mm
O.D. inch mm
Max.W.P. psi MPa
1/2 5/8 3/4 1 1-1/4 1-1/2 2
12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.87 1.03 1.14 1.39 1.80 2.07 2.76
inch
mm
inch
mm
1/2 5/8 3/4 1 1-1/4 1-1/2
12.7 15.9 19.0 25.4 31.8 38.1
0.87 1.04 1.14 1.41 1.80 2.20
22.2 26.4 29.0 3,500 35.9 45.6 55.9
inch
mm
O.D. inch mm
1/2 5/8 3/4 1 1-1/4 1-1/2
12.7 15.9 19.0 25.4 31.8 38.1
0.87 1.04 1.14 1.41 1.91 2.20
inch
mm
O.D. inch mm
1/2 5/8 3/4 1 1-1/4 1-1/2 2
12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.87 1.04 1.14 1.44 1.93 2.20 2.95
22.2 26.2 29.0 35.2 3,000 45.6 52.7 70.0
Min.B.P. psi MPa
Min.B.R. inch mm
3.94 5.12 5.51 20.5 15,000 102.5 7.09 9.06 12.20 16.93
100 130 140 180 230 310 430
Weight lb s/ ft g /m
0.42 0.57 0.75 0.95 1.71 2.05 3.87
Reinforcement
630 860 1,130 1,430 2,560 3,070 5,800
2W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34
4S
6S
UZ/34 HW/40 KN/41
UB/34
UZ/34 HW/40 -
EQ25 Maximum Working Pressure
24.5MPa 3,500PSI
Catalog Number
EQ2508 EQ2510 EQ2512 EQ2516 EQ2520 EQ2524
I.D.
O.D.
Max.W.P. MPa
psi
Min.B.P. MPa
psi
Min.B.R. mm
inch
3.94 5.12 6.30 24.5 17,500 122.5 7.09 10.24 12.60
100 130 160 180 260 320
Weight g /m
Reinforcement
lb s/ ft
0.52 0.67 0.75 1.17 1.71 2.89
780 1,000 1,130 1,750 2,560 4,340
4S
6S
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UB/34
UB/34
UZ/34 KN/41
UZ/34 -
EQ28 Maximum Working Pressure
27.5MPa 4,000PSI
Catalog Number
EQ2808 EQ2810 EQ2812 EQ2816 EQ2820 EQ2824
I.D.
Max.W.P. psi MPa
22.2 26.4 29.0 4,000 35.9 48.6 55.9
Min.B.P. psi MPa
Min.B.R. inch mm
3.94 5.12 6.30 27.5 20,000 137.5 7.87 11.81 14.17
100 130 160 200 300 360
Weight lb s/ ft g /m
0.52 0.67 0.75 1.17 2.43 2.89
Reinforcement
780 1,000 1,130 1,750 3,640 4,340
4S
6S
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UB/34
KN/41
UB/34
UZ/34 -
EQ31 Maximum Working Pressure
31.0MPa 4,500PSI
Reinforcing
Catalog Number
EQ3108 EQ3110 EQ3112 EQ3116 EQ3120 EQ3124 EQ3132
18
I.D.
Max.W.P. psi MPa
22.2 26.4 29.0 36.6 4,500 49.0 55.9 75.0
Min.B.P. psi MPa
Min.B.R. inch mm
4.72 6.30 7.87 31.0 22,500 155.0 9.45 12.60 15.35 22.05
120 160 200 240 320 390 560
Weight lb s/ ft g /m
0.53 0.67 0.75 1.33 2.53 3.00 5.27
Reinforcement
800 1,000 1,130 2,000 3,800 4,500 7,900
4S
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UB/34
UB/34
UZ/34 6S
KN/41 EX/41
-
SAE series / DIN series
SAE Series
Temperature Range
●Compatible Fluid / Mineral Oil
DIN Series ●Compatible Fluid / Mineral Oil ●Only Hose Available
Fluid
Ambient
R1,R2,4SP,4SH
-40 -40
to +100 to +212
-40 -40
to +70 to +158
R12,R13,R15
-40 -40
to +121 to +250
-40 -40
to +70 to +158
R1AT SAE 100R1
Catalog Number
R1AT04 R1AT06 R1AT08 R1AT10 R1AT12 R1AT16 R1AT20 R1AT24 R1AT32
I.D.
O.D
inch
mm
inch
mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.53 0.69 0.81 0.94 1.09 1.41 1.70 1.98 2.53
13.5 17.5 20.6 23.8 27.8 35.8 43.2 50.4 64.3
inch
mm
inch
mm
1/4 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.59 0.75 0.87 1.00 1.16 1.50 1.89 2.14 2.64
15.1 19.1 22.2 25.4 29.4 38.1 48.0 54.4 67.0
Max.W.P. psi MPa
3260 2610 2320 1880 1520 1260 890 720 580
22.5 18.0 16.0 13.0 10.5 8.7 6.2 5.0 4.0
Min.B.P. psi MPa 13040 10440 9280 7520 6080 5040 3560 2880 2320
90.0 72.0 64.0 52.0 42.0 34.8 25.5 20.0 16.0
Min.B.R. inch mm
3.94 4.92 7.09 8.07 9.45 11.81 16.54 19.69 24.80
100 125 180 205 240 300 420 500 630
Weight lbs/ft g/m
0.15 220 0.23 340 0.28 420 0.34 510 0.42 630 0.65 960 0.81 1,210 1.03 1,540 1.30 1,940
Reinforcement
1W
R2AT SAE 100R2
Catalog Number
R2AT04 R2AT06 R2AT08 R2AT10 R2AT12 R2AT16 R2AT20 R2AT24 R2AT32
I.D.
O.D
Max.W.P. psi MPa
5800 4780 3980 3620 3110 2390 1810 1300 1160
40.0 33.0 27.5 25.0 21.5 16.5 12.5 9.0 8.0
Min.B.P. psi MPa 23200 19120 15920 14480 12440 9560 7240 5200 4640
160.0 132.0 110.0 100.0 86.0 66.0 50.0 36.0 32.0
Min.B.R. inch mm
3.94 4.92 7.09 8.07 9.45 11.81 16.54 19.69 24.80
100 125 180 205 240 300 420 500 630
Weight lbs/ft g/m
0.26 0.36 0.42 0.52 0.62 0.96 1.32 1.51 1.79
380 540 630 770 920 1,430 1,970 2,240 2,660
Reinforcement
2W
19
SAE series / DIN series R12A SAE 100R12
Catalog Number
Construction
R12A06 R12A08 R12A10 R12A12 R12A16 R12A20 R12A24 R12A32
●Inner Tube /
Synthetic Rubber ●Outer Cover / Synthetic Rubber ●Reinforcement / 4S
I.D.
O.D
inch
mm
inch
mm
3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2
9.5 12.7 15.9 19.0 25.4 31.8 38.1 50.8
0.80 0.94 1.08 1.21 1.50 1.85 2.11 2.63
20.3 23.8 27.4 30.7 38.0 47.0 53.5 66.7
inch
mm
inch
mm
3/4 1 1-1/4 1-1/2 2
19.0 25.4 31.8 38.1 50.8
1.26 1.52 1.96 2.26 2.80
32.1 38.7 49.8 57.3 71.1
inch
mm
inch
mm
3/8 1/2 3/4 1 1-1/4 1-1/2
9.5 12.7 19.0 25.4 31.8 38.1
0.80 0.94 1.21 1.52 1.96 2.26
20.3 23.8 30.7 38.7 49.8 57.3
inch
mm
inch
mm
3/8 1/2 5/8 3/4 1 1-1/4 1-1/2
9.5 12.7 15.9 19.0 25.4 31.8 38.1
0.84 0.97 1.11 1.27 1.56 2.00 2.25
21.4 24.6 28.2 32.2 39.7 50.8 57.2
inch
mm
inch
mm
3/4 1 1-1/4 1-1/2 2
19.0 25.4 31.8 38.1 50.8
1.27 1.52 1.79 2.11 2.68
32.2 38.7 45.5 53.5 68.1
Max.W.P. psi MPa
4,000 4,000 4,000 4,000 4,000 3,000 2,500 2,500
28.0 28.0 28.0 28.0 28.0 21.0 17.5 17.5
Min.B.P. psi MPa
Min.B.R. inch mm
16,000 112.0
4.92 7.09 7.87 9.45 11.81 16.54 19.69 25.20
16,000 112.0 16,000 112.0 16,000 112.0 16,000 112.0 12,000 10,000 10,000
84.0 70.0 70.0
125 180 200 240 300 420 500 640
Weight lbs/ft g/m
0.50 0.53 0.73 0.83 1.30 1.87 2.22 2.93
750 800 1,100 1,250 1,950 2,800 3,330 4,400
Reinforcement
4S
R13A SAE 100R13
Catalog Number
Construction ●Inner Tube /
Synthetic Rubber ●Outer Cover / Synthetic Rubber ●Reinforcement / 4S(R13A12/R13A16) 6S(R13A20/R13A24/R13A32)
R13A12 R13A16 R13A20 R13A24 R13A32
I.D.
O.D
Max.W.P. psi MPa
5,000 5,000 5,000 5,000 5,000
35.0 35.0 35.0 35.0 35.0
Min.B.P. psi MPa
20,000 137.9
Min.B.R. inch mm
9.45 11.81 16.54 19.69 25.20
20,000 137.9 20,000 137.9 20,000 137.9 20,000 137.9
240 300 420 500 640
Weight lbs/ft g/m
1.07 1.50 2.93 3.20 4.80
1,600 2,250 4,400 4,800 7,200
Reinforcement
4S 6S
R15A SAE 100R15
Catalog Number
Construction ●Inner Tube /
R15A06 R15A08 R15A12 R15A16 R15A20 R15A24
Synthetic Rubber ●Outer Cover / Synthetic Rubber ●Reinforcement / 4S(R15A06/RA15A08/ R15A12/R15A16) 6S(R15A20/R15A24)
I.D.
O.D
Max.W.P. psi MPa
6,000 6,000 6,000 6,000 6,000 6,000
42.0 42.0 42.0 42.0 42.0 42.0
Min.B.P. psi MPa
24,000 168.0
Min.B.R. inch mm
5.91 7.87 10.43 12.99 17.52 20.87
24,000 168.0 24,000 168.0 24,000 168.0 24,000 168.0 24,000 168.0
150 200 265 330 445 530
Weight lbs/ft g/m
0.48 0.61 0.98 1.45 2.59 3.17
720 920 1,470 2,180 3,890 4,760
Reinforcement
4S
6S
4SP DIN 4SP
Catalog Number
Construction ●Inner Tube /
4SP06 4SP08 4SP10 4SP12 4SP16 4SP20 4SP24
Synthetic Rubber ●Outer Cover / Synthetic Rubber ●Reinforcement / 4S
I.D.
O.D
Max.W.P. psi MPa
6,500 6,000 5,100 5,100 4,100 3,000 2,700
44.5 41.5 35.0 35.0 28.0 21.0 18.5
Min.B.P. psi MPa
26,000 178.0
7.09 9.06 9.84 11.81 13.39 18.11 22.05
24,000 166.0 20,400 140.0 20,400 140.0 16,400 112.0 12,000 10,800
Min.B.R. inch mm
84.0 74.0
180 230 250 300 340 460 560
Weight lbs/ft g/m
0.55 0.63 0.80 1.07 1.53 2.13 2.53
820 950 1,200 1,600 2,300 3,200 3,800
Reinforcement
4S
4SH DIN 4SH
Catalog Number
Construction ●Inner Tube /
4SH12 4SH16 4SH20 4SH24 4SH32
Synthetic Rubber ●Outer Cover / Synthetic Rubber ●Reinforcement / 4S
Reinforcing
20
I.D.
O.D
Max.W.P. psi MPa
6,100 5,500 4,700 4,200 3,600
42.0 38.0 32.5 29.0 25.0
Min.B.P. psi MPa
Min.B.R. inch mm
24,400 168.0 11.02 22,000 152.0 13.39 18,800 130.0 18.11 16,800 116.0 22.05 14,400 100.0 27.56
280 340 460 560 700
Weight lbs/ft g/m
1.07 1.50 1.73 2.13 3.20
1,600 2,250 2,600 3,200 4,800
Reinforcement
4S
Special Application Rubber Hoses ● ● ● ● ●
JW Series For Hydraulic Jack
Compatible Fluid / Mineral Oil Inner Tube / Oil Resistant Synthetic Rubber Outer Cover / Weather Resistant Synthetic Rubber Temperature Range: fluid / -40℃ to 100℃(-40°F to 212°F) Temperature Range : ambient / -40℃ to 70℃(-40°F to 158°F)
JW70 Maximum Working Pressure
68.5MPa 9,900PSI
Catalog Number
JW7004 JW7006 JW7008
I.D. inch
1/4 3/8 1/2
mm
O.D. inch mm
6.3 9.5 12.7
0.66 0.82 0.87
Max.W.P. psi MPa
16.7 20.8 9,900 22.2
Min.B.P. psi MPa
196.0 68.5 22,500 154.0 20,000 138.0 28,500
Min.B.R. inch mm
3.54 5.51 6.69
Weight lb s/ ft g /m
90 140 170
0.30 0.43 0.55
450 750 830
Reinforcement
2W 4S
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
ZP/45 KH/40 UB/34
ZP/45 -
UB/34
Note: The types of coupling threads for the JW70 series are designated “R” and “Q.” Use a pressure waveform (jack waveform) that can withstand shock pressure.
JWK Maximum Working Pressure
Catalog Number
98.0 137.0MPa JWK04 ~
14,200 19,900PSI ~
I.D. inch
1/4 3/8 1/2
JWK06 JWK08
mm
O.D. inch mm
6.3 9.5 12.7
0.73 0.97 1.09
Max.W.P. psi MPa
Min.B.P. psi MPa
18.6 19,900 137.0 40,000 275.0 24.6 32,000 219.5 14,200 98.0 27.8 28,000 192.0
Min.B.R. inch mm
3.54 4.72 6.69
Weight lb s/ ft g /m
90 120 170
Reinforcement
0.30 850 0.43 1,150 4S+1W 0.55 1,360
Compatible coupling/relevant page Factory-assembled
EK/45
■Hoses for jacks also include PrimoLine hoses. (Refer to pages 59 to 63.)
Note: The types of coupling threads for the JWK series hoses are designated “R” and “Q.” Use a pressure waveform (jack waveform) that can withstand shock pressure.
● ● ● ● ● ●
VW Series For Suction Line
Compatible Fluid / Mineral Oil Inner Tube / Oil Resistant Synthetic Rubber Outer Cover / Weather Resistant Synthetic Rubber Temperature Range: fluid / -40℃ to 100℃(-40℃ to 212°F) Temperature Range : ambient / -40℃ to 70℃(-40℃ to 158°F) Maximum Allowable Suction : -0.08665 Mpa
VW Maximum Working Pressure
3.0MPa 400PSI
Catalog Number
VW16 VW20 VW24 VW32
inch
I.D. mm
O.D. inch mm
1 1-1/4 1-1/2 2
25.4 31.8 38.1 50.8
1.40 1.64 1.90 2.50
35.6 41.7 48.3 63.4
Max.W.P. psi MPa
400
Min.B.P. psi MPa
3.0 1,600
Min.B.R. inch mm
5.51 7.09 12.0 9.06 10.63
Weight lb s/ ft g /m
140 180 230 270
0.63 940 0.77 1,150 0.90 1,350 1.53 2,300
Reinforcement
1W 2W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UT/27
UT/27
LC/27 HW/40
LC/27 HW/40
Check the delivery dates of products marked ▲.
Rubber Hoses for Water Cleaning 1 Lightweight and flexible design
● ● ● ● ●
2 Enhanced safety
The lightweight and flexible design of the hoses makes them easy to install. (The WA14 series is about 40% lighter and more flexible than the WJ series by Bridgestone.)
The hoses offer enhanced safety by absorbing the shock when the fluid supply goes on or off.
Compatible Fluid / Water Inner Tube / Water-resistant synthetic rubber Outer Cover / Abrasion-resistant, weather-resistant synthetic rubber Temperature Range: fluid / 0°C to 80°C (32°F to 176°F) Temperature Range : ambient / 0°C to 70°C (32°F to 158°F)
WA14 Maximum Working Pressure
14.0MPa 2,000PSI
Catalog Number
WA1404 WA1406 WA1408
I.D. inch
1/4 3/8 1/2
mm
O.D. inch mm
6.3 9.5 12.7
0.53 0.65 0.80
mm
O.D. inch mm
6.3 9.5 12.7
0.53 0.65 0.78
Max.W.P. psi MPa
13.4 16.5 2,000 20.2
Min.B.P. psi MPa
14.0 5,000
35.0
Min.B.R. inch mm
1.97 2.76 3.15
Weight lb s/ ft g /m
50 70 80
0.31 0.44 0.55
140 200 250
Reinforcement
1B
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UL/30
UL/30
WAR Maximum Working Pressure
20.5MPa 3,000PSI
Catalog Number
WAR04 WAR06 WAR08 Caution
I.D. inch
1/4 3/8 1/2
Max.W.P. psi MPa
13.4 16.5 3,000 19.8
Min.B.P. psi MPa
20.5 8,000
51.5
Min.B.R. inch mm
1.97 1.97 2.76
Weight lb s/ ft g /m
50 50 70
0.31 0.44 0.55
140 200 250
Reinforcement
1B
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UL/30
UL/30
The reinforcing for the WA14 and WA R series is made from special synthetic fibers. Do not install these hoses in an environment where they are likely to come into contact with sharp objects (as their reinforcing may be cut, causing the hose to burst.) You are recommended to install WJ or WB21 series hoses in the environment above.
21
Special Application Rubber Hoses
● ● ● ● ●
SA Series For Steam For steam piping, use the SF series hoses (shown on page 51). Replacement of the hose may be required after a short usage period depending on the usage conditions.
Compatible Fluid / Steam Inner Tube / Heat Resistant Synthetic Rubber Outer Cover / Heat Resistant Synthetic Rubber Temperature Range: fluid / 4℃ to 210℃(39°F to 410°F) Temperature Range : ambient / -40℃ to 70℃(-40°F to 158°F)
SA Maximum Working Pressure
2.0MPa 300PSI
Catalog Number
SA08 SA12 SA16
I.D. inch
1/2 3/4 1
mm
O.D. inch mm
Max.W.P. psi MPa
12.7 19.0 25.4
1.03 1.28 1.64
300
26.1 32.4 41.6
SA hose does not fit mineral oil application.
Min.B.P. psi MPa
2.0 1,800
Min.B.R. inch mm
12.0
5.91 8.27 9.84
Weight l bs /f t g/ m
150 0.41 610 210 0.54 810 250 0.88 1,320
*For information about other size hoses, contact us.
Reinforcement
Compatible coupling/relevant page Factory-assembled
1W
SK
*Be sure to read the following description.
■Be sure to read the following before use Superheated steam
●Use SA series steam hoses to convey hot water condensate *1 or saturated steam*2. Do not use them to convey superheated steam*3 or a mixture of steam and air. Doing so could deteriorate the inner tube rubber, significantly reducing the life of t he hose. (The terms marked with an asterisk are described below.) *1 Hot water condensate Th e wa te r ev ap or at io n te mpe ra tu re , wh ic h depends on pressure, is also called the saturation temperature. Water at the saturation temperature is called saturated water. While this saturated water is being heated, it continues to evaporate without any increase in its temperature. The condensate (vapor + water) generated at this stage is called hot water condensate.
Couplings
*2 Saturated steam Whi le the hot water condensate is being heated, the water continues to evaporate and finally disappears. The steam generated when there is no water remaining is called saturated steam.
*3 Superheated steam
T e m p e r a t u r e
When the saturated steam is further heated, its temperature rises. Th is st ea m is ca ll ed superheated steam.
hot water condensate
100
0
1.0
1.5
2.0
Pressure(MPa)
Use this hose in
SK Series Y(HEX)
R
R
Thread A L Male British Tapered Pipe Thread(BSPT)
G
X(HEX)
Y(HEX)
30°
SK08R SK12R SK16R
1/2 3/4 1
Female Japanese Industrial Pipe Thread (JIS) Female 30°Seat
inch
mm
1.06 1.42 1.61
27 36 41
inch
0.71 0.79 0.87
mm
18 20 22
(L) inch
1.06 1.42 1.61
SK08F SK12F SK16F
1/2 3/4 1
inch
mm
1.06 1.42 1.61
mm
Weight lbs
inch
27 36 41
2.80 3.46 3.98
g
71 0.68 83 1.22 98 1.36
(L)
Y
Catalog Number Thread
L
A
Y
Catalog Number
F
In case of 200℃, if pressure is less than 1.5Mpa, hose life is reduced dramatically by superheated steam conditions. Therefore in case of 200℃ situation, pressure 1.5 to area. 2.0 MPa is required.
saturated steam line
214 200 183
mm
Weight lbs
71 0.69 88 1.34 101 1.48
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment (for cores only)
■How to install SK series couplings
Shell
Insert
◎Set the hook of shell in the groove of insert ◎SK series is all re-usable type Retighten the bolt if leakage from coupling is found If retightening can not stop leakage, cut the hose and retighten. In case the clamping portion becomes loose after a certain period of usage, retightening will be required. Not following these instructions will lead to hose failure like hose coupling blow-off and leakage.
◎ Tighten the bolt referring to the following crevice figure
Crevice (both end)
Hook
Reinforcing
22
310 555 615
Hose size
Crevice (mm)
Torelance
SA08 SA12 SA16
2 5 6
±1
g
315 610 670
● Compatible Fluids / ● Temperature Temperature Range: fluid / Mineral hydraulic oil or mineral engine oil −40°C to 135°C (−40°F (−40°F to 275°F) ● Inner Tube: Heat- and oil-resistant synthetic rubber Temperature Range: ambient / ● Temperature ● Outer Cover: Heat-, oil-, and weather-resistant synthetic rubber −40°C to 100°C (−40°F (−40°F to 212°F)
Heat- and Oil-resistant Hoses
HM Maximum Working Pressure
7.0MPa 1,000PSI
Catalog Number
I.D. inch
HM12 HM16
mm
O.D. inch mm
19.0 25.4
1.04 1.31
3/4 1
Max.W.P. psi MPa
26.5 1,000 33.3
Push on Hose
Min.B.P. psi MPa
7 . 0 4 , 0 00
Min.B.R. inch mm
28.0
5.51 7.09
140 180
Weight l bs bs /f /f t g/ m
0.37 0.57
Reinforcement
550 850
Compatible coupling/relevant page Factory-assembled
1W
UN/27
You can easily attach couplings to these hoses without using a crimping machine. This enables on-site assembly, so you no longer need to have extra assembled hoses in stock.
ACT Maximum Working Pressure
2.0MPa 300PSI
Catalog Number
I.D. inch
ACT04 ACT06 ACT08
R
Catalog Number
Y
A L
Male British Tapered Pipe Thread(BSPT)
G
0.49 0.63 0.75
12.5 16.0 19.0
30 0
*Check the delivery dates of
D φ
L
Female Japanese Industrial Pipe Thread (JIS) Female 30 ° Seat
10.0
■ Adapters Y
A
(L)
D
i nc nc h m m inch mm inch mm inch mm ibs
AT06R AT06R
3/8 0.75 19 0.59 15 0.47 12 1.77 45 0.10 45
AT08R AT08R
1/2 0.94 24 0.71 18 0.59 15 2.05 52 0.18 80
AT12R AT12R
3/4 1.18 30 0.79 20 0.83 21 2.83 72 0.39 175
Y inch
Weight l bs bs /f /f t g/ m
2.36 2.76 4.72
0.08 0.11 0.15
60 70 120
Reinforcement
120 170 220
Compatible coupling/relevant page Factory-assembled
1B
AT
ibs
g
AT04F AT04F
1/4 0.67
17
0.31
8
1.57
40
0.07
30
AT06F AT06F
3/8 0.75
19
0.47
12
1.69
43
0.09
40
AT08F AT08F
0.59
AT12F AT12F
3/4 1.26
32
0.83
G 30° 30°
A
15
1.97
50
0.15
21
2.68
68
0.26 120
70
G
° 0 3
b φ
d
R
φb
Y
(L) A
B
Catalog Number
R
8001RG04H14B
1/4 0.55 14 1.45 37 0.51 13 0.63 16 0.07 30
8001RG06H19B
3/8 0.75 19 1.61 41 0.59 15 0.71 18 0.11 50
8001RG08H22B
1/2 0.87 22 1.89 48 0.71 18 0.79 20 0.20 90
8001RG12H30B
3/4 1.18 30 2.13 54 0.79 20 0.87 22 0.35 160
Catalog Number
R
8025RG04
1/4 1.06
27 0.94 24 0.43
8025RG06
3/8 1.18
8025RG08
1/2 1.26
8025RG12
3/4 1.46
B L
G
mm
24
materials : Brass
C
mm inch mm inch
1/2 0.94
Y
8 1.69 43 0.07 30
(L)
D
R
g
1/4 0.67 17 0.51 13 0.31
R
2.0 1,50 0
Min.B.R. inch mm
AT seri series es and and Adapte Adapters rs
AT04R AT04R
Catalog Number
Y
30°
R
Min.B.P. psi MPa
100m hoses, as they are available on request.
materials : Brass
D φ
F
6.3 9.5 12.7
Max.W.P. psi MPa
Temperature Range: fluid / -40℃ to 93℃(Oil), 0℃ to 50℃(Water) -40°F to 199°F(Oil), 32°F to 122°F(Water) ●Temperature ●Temperature Range : ambient / -40℃ to 70℃(Oil), 0℃ to 70℃(Water) -40°F to 158°F(Oil), 32°F to 158°F(Water)
Coupli Couplings ngs and adapto adaptorr R
O.D. inch mm
1/4 3/8 1/2
●Compatible Fluid / Mineral Oil, Water ●Inner Tube / Oil Resistant Synthetic Rubber ●Outer Cover / Weather Resistant Synthetic Rubber
■Couplings
mm
g
inch mm inch mm inch mm inch mm ibs
D
C inch
mm inch
G mm inch
mm
g
ibs
11 0.11
50
30 1.06 27 0.43
11 0.15
70
32 1.18 30 0.55
14 0.24 110
37 1.57 40 0.87
22 0.46 210
tightening torque ( page 82 )
■How to install coupling Cut the hose perpendicular to the axis by tube cutter. Put water or soap suds hose inside and inserting portion of coupling.
Fix the coupling with clamp and insert the hose.
Short grip will cause oil leakage. Cutting surface should be less than 10 degree.
23
Special Application Application Rubber Hoses ● ● ● ● ●
WH Series For Pressure Washer
Compatible Fluid / Water Inner Tube / Hot Water Resistant Synthetic Rubber Outer Cover / Weather Resistant Synthetic Rubber Temperature Range: fluid / 0℃ to 120℃(32℉ to 248℉) Temperature Range: ambient / 0℃ to 70℃(32℉ to 158℉)
WH21 Maximum Working Pressure
20.5MPa 3,000PSI
Catalog Number
WH2106
I.D. inch
O.D. mm
3/8
9.5
Max.W.P. MPa
inch
mm
0.68
17. 2 3,000
Min.B.P. MPa
psi
psi
20.5 9.000
61.5
Min.B.R. mm
inch
3.35
Weight g /m /m
lb s/ s/ ft ft
85 0.24
36 0
Reinforcement
1W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UF/45
GA(UL)/45
WH hose does not fit mineral oil application.
● ● ● ●
Compatible Fluid / Water-glycol and mineral hydraulic oil Inner Tube / Oil- and water-glycol-resistant synthetic rubber Outer Cover / Weather-resistant synthetic rubber Temperature Temperature Range: fluid / −40°C to 60°C (−40°F to 140°F) for water-glycol, −40°C to 100°C (−40°F to 212°F) for oil Temperature Range: ambient / −40°C / −40°C to to60°C 60°C (−40°F to140°F) for water-glycol, ● Temperature −40°C to 70°C (−40°F to 158°F) for oil
Rubber Hoses for Both Water-Glycol and Mineral Hydraulic Oil
WE21 Maximum Working Pressure
20.5MPa 3,000PSI
Catalog Number
WE2104 WE2106 WE2108 WE2112-22 WE2116-22 WE2120-22 WE2124-22 WE2132 Warning
inch
I.D. mm
O.D. inch mm
1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 19.0 25.4 31.8 38.1 50.8
0.59 0.75 0.87 1.19 1.46 1.88 2.20 2.76
Max.W.P. psi MPa
15.1 19.1 22.2 30.0 3 , 00 0 37.2 47.7 56.0 70.0
Min.B.P. psi MPa
2 0 .5 8 , 0 0 0
Min.B.R. inch mm
3.15 3.94 5.51 8.27 82.0 10.63 12.60 15.75 22.05
Weight l bs bs/ ft ft g/ m
80 0.82 100 1.10 140 1.43 210 3.53 270 4.41 320 8.38 400 9.92 560 12.79
370 500 650 1,600 2,000 3,800 4,500 5,800
Reinforcement
2W
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34
4S
UB/34
6S
KN/41
UZ/34
UB/34
UZ/34 -
We recommend using couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). Do not use high water base fluid (HWBF) with the hoses listed above. Doing so could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
WE28 Maximum Working Pressure
27.5MPa 4,000PSI
Catalog Number
WE2804 WE2806 WE2808 WE2812-22 WE2816 WE2820 WE2824 WE2832 Warning
Reinforcing
24
inch
I.D. mm
O.D. inch mm
1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2
6.3 9.5 12.7 19.0 25.4 31.8 38.1 50.8
0.59 0.75 0.88 1.19 1.56 1.88 2.20 2.91
Max.W.P. psi MPa
15.1 19.1 22.4 30.1 4 , 00 0 39.5 47.7 56.0 74.0
Min.B.P. psi MPa
Min.B.R. inch mm
2.76 3.54 3.94 6.69 27.5 16,000 112.0 8.66 11.81 14.17 16.93
Weight l bs bs/ ft ft g/ m
70 0.84 90 1.17 100 1.48 170 3.57 220 5.07 300 7.94 360 9.48 430 17.42
380 530 670 1,350 2,300 3,600 4,300 7,900
Reinforcement
2W
4S
6S
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
UZ/34 UB/34 UZ/34 UB/34 GB/45
UZ/34 UB/34
UB/34
-
KD/41
We recommend using couplings on which the wetted parts only are nickel chrome plated (the catalog numbers of these couplings end with X103). Do not use high water base fluid (HWBF) with the hoses listed above. Doing so could cause the hoses to burst or fluid to leak. Severe personal injury or death may result if these instructions are not followed.
● Compatible Fluid / Air
PA03-DA Series S eries For Air
● ● ● ●
*It is usable for not only air with misted oil but also dry air Inner Tube / Weather Resistant Synthetic Rubber Outer Cover / Weather Resistant Synthetic Rubber -40℃ to 60℃(-40℉ to 140 ℉) Temperature Range: fluid / -40 Temperature Range: ambient / -40℃ to 60℃(-40℉ to 140℉)
PA03-DA Maximum Working Pressure
3.5MPa 500PSI
Catalog Number
PA0304-DA PA0306-DA PA0308-DA PA0312-DA PA0316-DA
I.D. inch
1/4 3/8 1/2 3/4 1
mm
O.D. inch mm
6.3 9.5 12.7 19.0 25.4
0.55 0.69 0.83 1.24 1.48
14.0 17.4 21.2 31.4 37.5
Max.W.P. psi MPa
500
Min.B.P. psi MPa
3.5 2,000
14.0
Min.B.R. inch mm
2.17 2.56 3.54 5.12 6.69
55 65 90 135 170
Weight l bs bs /f /f t g /m /m
0.12 0.16 0.20 0.43 0.55
180 240 300 650 840
Reinforcement
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
AS/27 4C
UL/30 UT/27
25
Special Purpose Hose
1
Large-bore high-pressure hoses with extended life and increased fatigue endurance
The result of our extensive materials research, the JUMBO ACE series of hoses provide high flexibility while offering outstanding durability. They have survived shock pressure tests in which they have a maximum working pressure equal to 1/4 of the minimum burst pressure and were subjected to 200,000 applications.
●Compatible Fluid Mineral Hydraulic Oil ●Inner Tube Oil-resistant synthetic rubber
2
●Outer Cover Weather-resistant synthetic rubber
Maximum length of 40m enables an extended range of applications
●Temperature Range : fluid -40 -40° C to to 10 100° C (-40 (-40° F to to 21 212° F)
Conventional large-bore high-pressure hoses typically have a length of up to 20m. The JUMBO ACE series features a maximum length of 40m, marking a breakthrough in technology. The JUMBO ACE series is a revolutionary line of hoses that meets the needs of large oil pressure systems.
●Recommended Temperature Range: ambient -40 -40° C to t o 70 7 0° C (-40 (-4 0° F to t o 15 1 58° F)
3
Compact and lightweight design offers significantly increased work efficiency
The JUMBO ACE series produces the expected effect as a large-bore high-pressure hose. For example, if the fluid speed is 4m/sec at a maximum working pressure of 20.5MPa and a flow rate of 900 liters/min, then three EQ2124 (38φ) hoses by Bridgestone are required. These hoses can be replaced by just one JUMBO ACE JBS40 hose. The JUMBO ACE series enables compact plumbing designs and weighs about two thirds of the weight of conventional hoses.
JBT/JBF/JBS Maximum Working Pressure
I.D.
Catalog Number
3.0 20.5MPa
inch
JBT40 JBT48 JBF40 JBF48 JBS40 JBS48
~
400 3,000PSI ~
2
1/2
3 2 1/2 3 2 1/2 3
mm
O.D. inch mm
63.5 76.2 63.5 76.2 63.5 76.2
3.11 3.58 3.24 3.77 3.35 3.91
79.0 91.0 82.4 95.8 86.4 99.1
Max.W.P. psi MPa
700 400 2,000 1,500 3,000 2,500
Min.B.P. psi MPa
4.9 3.0 14.0 10.5 20.5 17.0
2,800 1,600 8,000 6,000 12,000 10,000
Min.B.R. inch mm
19.5 12.0 56.0 42.0 82.0 68.0
23.23 31.50 25.98 29.53 25.98 29.53
Weight l bs bs /f /f t g/ m
590 760 660 750 660 750
2.40 2.47 3.67 4.33 5.13 6.07
Reinforcement
3,600 3,700 5,500 6,500 7,700 9,100
Compatible coupling/relevant page Factory-assembled
2W
EC
4S
DX
6S
EX
Coup Coupli ling ngs s EC / DX DX / EX Se Seri ries es R
R6
Y(HEX)
Y
Catalog Number
Thread
EC40R6 EC48R6
A
inch
2 1/2 3
mm
3.54 3.94
90 100
(L)
A inch
mm
1.26 1.30
inch
32 33
Weight
mm
5.79 5.79
147 147
lbs
kg
5.95 6.61
2.7 3.0
(L)
F
X (HEX (H EX ) Y (HEX (H EX )
G ° 0 3
Y
Catalog Number
Thread
EC40F EC48F
(L)
2 1/2 3
inch
mm
3.54 3.94
90 100
(L)
A inch
3.54 3.94
mm
inch
90 100
5.59 4.69
Weight
mm
142 119 119
lbs
kg
6.39 9.70
2.9 4.4
Female Japanese Industrial Pipe Thread (JIS) Female 30°Seat
2.4
K
A
Catalog Number
1 . 4
inch
C (L)
Bolt dia
B A
DX40K65 EX40K65 DX48K80 EX48K80 DX40K265 EX40K265 DX48K280 EX48K280
5.51 5.51 6.10 6.10 5.04 5.04 5.51 5.51
B
mm
140 140 155 155 128 128 140 140
inch
3.94 3.94 4.41 4.41 3.62 3.62 4.06 4.06
mm
100 100 112 112 92 92 103 103
(L)Bolt
C inch
1.77 1.77 1.77 1.77 1.77 1.77 1.77 1.77
mm
45 45 45 45 45 45 45 45
inch
6.34 7.64 7.60 8.98 6.34 7.72 7.64 8.98
mm
161 194 193 228 161 196 194 228
M20 M20 M22 M22 M20 M20 M22 M22
JIS B 2291 21MPa(210kgf/cm ) Flange 2
Materials : Steel with Zinc Plating
Reinforcing
26
Bolt dia inch
mm
0.87 0.87 0.94 0.94 0.87 0.87 0.94 0.94
22 22 24 24 22 22 24 24
Weight lbs
kg
16.76 7.6 20.73 9.4 22.71 10.3 25.80 11.7 14.33 6.5 18.30 8.3 19.40 8.8 22.93 10.4
Couplings
AS / LS / UT / UN / LC series
R
Catalog Number
R
Y(HEX)
A
(L)
Male British Tapered Pipe Thread(BSPT)
F
AS04R LS04R AS06R LS06R AS08R LS08R UT1012R UT12R UN12R UT16R UN16R UT20R LC20R LC24R LC32R
Catalog Number
X G
Y
。 30
(L)
Female Japanese Industrial Pipe Thread (JIS) Female 30°Seat
C
AS04F LS04F AS06F LS06F AS08F LS08F UT1012F UT12F UN12F UT16F UN16F UT20F LC20F LC24F LC32F
Catalog Number
X Y
G
30。
(L)
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
CR4
(L) 。
45 X H
30。
G
Female Parallel Pipe Thread, Bent 45º (Male 30º Seat)
AS04C LS04C AS06C LS06C AS08C LS08C UT1012C UT12C UN12C UT16C UN16C UT20C LC20C LC24C LC32C
Catalog Number
AS04CR4 AS06CR4 LS06CR4 AS08CR4 UT12CR4 UN12CR4 UT16CR4 UN16CR4 UT20CR4 LC24CR4
Y Thread 1/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 1 1 1 1/4 1 1/4 1 1/2 2
inch
0.67 0.67 0.75 0.75 0.87 0.87 1.18 1.18 1.18 1.42 1.42 1.81 1.81 1.97 2.56
mm
17 17 19 19 22 22 30 30 30 36 36 46 46 50 65
0.51 0.51 0.59 0.59 0.71 0.71 0.79 0.79 0.79 0.87 0.87 0.98 0.98 0.98 1.14
X Thread 1/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 1 1 1 1/4 1 1/4 1 1/2 2
inch
0.75 0.75 0.87 0.87 1.06 1.06 1.42 1.42 1.42 1.61 1.61 1.97 1.97 2.17 2.76
mm
19 19 22 22 27 27 36 36 36 41 41 50 50 55 70
1/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 1 1 1 1/4 1 1/4 1 1/2 2
inch
0.75 0.75 0.87 0.87 1.06 1.06 1.42 1.42 1.42 1.61 1.61 1.97 1.97 2.17 2.76
mm
19 19 22 22 27 27 36 36 36 41 41 50 50 55 70
0.67 0.67 0.75 0.75 0.87 0.87 1.18 1.18 1.18 1.42 1.42 1.81 1.81 1.97 2.56
1/4 3/8 3/8 1/2 3/4 3/4 1 1 1 1/4 1 1/2
inch
0.75 0.87 0.87 1.06 1.42 1.42 1.61 1.61 1.97 2.17
mm
19 22 22 27 36 36 41 41 50 55
13 13 15 15 18 18 20 20 20 22 22 25 25 25 29
inch
1.61 1.61 1.81 1.81 2.76 2.01 2.87 2.87 3.35 3.23 3.50 4.45 4.45 4.53 5.59
mm
17 17 19 19 22 22 30 30 30 36 36 46 46 50 65
0.67 0.67 0.75 0.75 0.87 0.87 1.18 1.18 1.18 1.42 1.42 1.81 1.81 1.97 2.56
mm
17 17 19 19 22 22 30 30 30 36 36 46 46 50 65
1.85 1.85 1.97 1.97 2.87 2.13 3.07 3.11 3.58 3.47 3.74 4.72 4.72 4.88 5.91
0.94 1.02 1.02 0.87 1.14 1.14 1.30 1.30 1.50 2.05
mm
24 26 26 22 29 29 33 33 38 52
41 41 46 46 70 51 73 73 85 82 89 113 113 115 142
Weight lbs
mm
47 47 50 50 73 54 78 79 91 88 95 120 120 124 150
1.85 1.85 1.97 1.97 2.87 2.13 3.11 3.11 3.58 3.47 3.74 4.72 4.72 4.88 5.91
mm
47 47 50 50 73 54 79 79 91 88 95 120 120 124 150
2.36 2.80 2.80 4.17 3.94 4.41 4.72 5.00 5.94 8.58
mm
60 71 71 106 100 112 120 127 151 218
30 30 55 50 115 80 185 215 257 325 401 645 645 755 1,280
Weight lbs
g
0.11 0.10 0.15 0.14 0.31 0.23 0.56 0.64 0.73 0.90 1.07 1.64 1.64 1.90 3.34
50 45 70 65 140 105 255 290 332 410 486 745 745 865 1,515
Weight lbs
g
0.11 0.11 0.15 0.15 0.31 0.23 0.42 0.66 0.74 0.91 1.08 1.68 1.67 1.97 3.39
(L) inch
g
0.07 0.06 0.12 0.11 0.25 0.17 0.41 0.47 0.57 0.72 0.88 1.42 0.42 1.66 2.82
(L) inch
H inch
mm
(L) inch
Y inch
X Thread
mm
Y inch
X Thread
(L)
A inch
50 50 70 70 140 105 270 300 337 415 491 760 760 895 1,540
Weight lbs
0.12 0.19 0.18 0.44 0.77 0.85 1.18 1.35 2.17 3.87
g
55 85 80 200 350 387 535 611 985 1,755
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
27
Couplings K3R9
UB / UZ series
JIS SSB (L)
90
A
Catalog Number UB08K315R9N67 UZ08K315R9N67
。
UB12K320R9N75 UB16K325R9N90 UB20K332R9N108 UZ20K332R9N108
3 ±
N
B
C
N
(L)Bolt
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
2.13 2.13 2.28 2.68 2.99 2.99
54 54 58 68 76 76
1.42 1.42 1.57 1.89 2.20 2.20
36 36 40 48 56 56
0.87 0.87 0.87 1.10 1.10 1.10
22 22 22 28 28 28
2.64 2.64 2.95 3.54 4.25 4.25
67 67 75 90 108 108
4.76 4.76 6.06 6.93 8.58 8.58
121 121 154 176 218 218
Weight g
lbs
M10 1.68
760
M10 1.68
760
M10 2.49 1,130 M12 4.06 1,840 M12 6.28 2,850 M12 6.28 2,850
C
B A
Bolt dia
JIS B 2291 20.5MPa Tube Flange
A1
UNF
Y
Y
Catalog Number inch
A (L)
Rigid Male O-ring Boss (Stud End)
UNF Y
A9
UZ04A1 UZ0406A1 UB06A1 UB0608A1 UB08A1 UB0810A1 UB10A1
0.67 0.75 0.75 0.87 0.87 1.06 1.06
inch B
φ
A
(L)
Male O-ring Face Seal
UZ04A9X604 UB06A9X604 UB08A9X604 UB10A9X604 UB12A9X604 UB16A9X604
17 19 19 22 22 27 27
mm
inch
3.62 3.90 3.90 4.37 4.37 5.00 5.00
9.2 9.9 9.9 11.1 11.1 12.7 12.7
1.85 1.97 2.07 2.07 2.17 2.32 2.32
0.75 0.75 0.87 1.06 1.26 1.61
mm
19 19 22 27 32 41
mm
47 50 53 53 55 59 59
Weight lbs
g
0.11 0.11 0.18 0.20 0.24 0.31 0.44
50 60 80 90 110 140 200
(L)
A
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
40
inch
Y
Catalog Number
(L)
A
mm
inch
mm
inch
0.47 0.43 0.51 0.61 0.67 0.69
12.0 11.0 13.0 15.5 17.0 17.5
2.09 2.09 2.36 2.91 3.27 3.50
mm
53 53 60 74 83 89
Weight lbs
g
2.56 0.19 0.28 0.46 0.72 1.09
65 85 125 210 325 495
Couplings
HW / KH / KN / KD / EX series
Q2R9
Catalog Number (L)
HW24Q2R9
。 90
X Thread 2-12
inch
1.97
mm
50
(L)
H inch
3.58
mm
91
inch
5.51
mm
140
Weight lbs
g
4.02
1,825
H
X UNF
Female O-Ring Face Seal
F2
UNF X 。 37
Y
Catalog Number
HW24F2 HW32F2
X Thread
inch
1 5/8 -12 1 5/8 -12
2.17 2.95
(L)
JIC 37° Female Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
46
mm
55 75
(L)
Y inch
2.17 2.95
mm
55 75
inch
5.35 6.65
mm
136 169
Weight lbs
2.92 5.75
g
1,325 2,610
Couplings
EA / EC / EK / GA / GB / UF / UG / ZP series
R
Catalog Number
R
Y(HEX)
A (L)
Male British Tapered Pipe Thread(BSPT)
F
EA0304R EC0304R EK04R GA04R GB04R ZP0406R ZP0406RH22 EK06R GA06R UF06R UG06R EK08R UF08R UG08R GB12R UG12R GB16R UG16R EC24R EC32R
Catalog Number
X G 。 30
Y
(L)
Female Japanese Industrial Pipe Thread (JIS) Female 30°Seat
Q
EA0304F EC0304F GA04F GB04F GA06F UF06F UG06F UF08F UG08F GB12F UG12F GB16F UG16F EC24F EC32F
Catalog Number Y (HEX)
G
Rounded
A (L)
ZP04Q EK04Q EK06Q EK08Q
Y Thread 1/4 1/4 1/4 1/4 1/4 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 3/4 3/4 1 1 1 1/2 2
inch
0.75 0.75 0.75 0.67 0.67 0.75 0.87 0.87 0.75 0.75 0.75 1.06 0.87 0.87 1.18 1.18 1.42 1.42 1.97 2.56
mm
19 19 19 17 17 19 22 22 19 19 19 27 22 22 30 30 36 36 50 65
1/4 1/4 1/4 1/4 3/8 3/8 3/8 1/2 1/2 3/4 3/4 1 1 1 1/2 2
inch
0.75 0.75 0.75 0.75 0.87 0.87 0.87 1.06 1.06 1.42 1.42 1.61 1.61 2.17 2.76
1/4 1/4 3/8 1/2
inch
0.75 0.75 0.87 1.06
13 13 13 13 13 12 12 15 15 15 15 18 18 18 20 20 22 22 25 29
inch
1.89 1.93 2.87 1.97 1.97 2.36 2.40 3.11 2.28 2.24 2.28 3.54 2.52 2.64 3.35 2.99 3.66 3.39 4.69 5.94
19 19 19 19 22 22 22 27 27 36 36 41 41 55 70
inch
mm
19 19 22 27
mm
0.75 0.75 0.67 0.67 0.75 0.75 0.75 0.87 0.87 1.18 1.18 1.42 1.42 1.97 2.56
19 19 17 17 19 19 19 22 22 30 30 36 36 50 65
inch
2.09 2.13 2.20 2.20 2.44 2.40 2.52 2.64 2.76 3.58 3.19 3.90 3.62 5.04 6.26
0.39 0.39 0.39 0.43
48 49 73 50 50 60 61 79 58 57 58 90 64 67 85 76 93 86 119 151
Weight lbs
mm
53 54 56 56 62 61 64 67 70 91 81 99 92 128 159
mm
10 10 10 11
inch
2.52 3.11 3.11 3.43
mm
64 79 79 87
g
0.10 0.11 0.23 0.10 0.11 0.19 0.19 0.31 0.17 0.20 0.21 0.49 0.29 0.28 0.62 0.56 0.95 0.87 1.98 3.51
45 50 105 45 50 85 85 140 75 90 95 220 130 125 280 255 430 395 900 1,590
Weight lbs
g
0.13 0.15 0.14 0.14 0.20 0.23 0.24 0.33 0.33 0.78 0.73 1.14 1.06 2.23 4.02
(L)
A inch
mm
(L)
Y
mm
Y Thread
mm
0.51 0.51 0.51 0.51 0.51 0.47 0.47 0.59 0.59 0.59 0.59 0.71 0.71 0.71 0.79 0.79 0.87 0.87 0.98 1.14
X Thread
(L)
A inch
60 70 65 65 90 105 110 150 150 355 330 515 480 1,010 1,825
Weight lbs
0.19 0.27 0.32 0.50
g
85 123 146 227
Equipped with safety hole
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
47
Couplings
EA / EC / EK / GA / GB / UF / UG / ZP series
C
Catalog Number
X Y
G
。
30
(L)
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
(L)
CR4
。 45
EA0304C EC0304C GA04C GB04C GA06C UF06C UG06C UF08C UG08C GB12C UG12C GB16C UG16C EC24C EC32C
Catalog Number
GA04CR4 GB04CR4
X
X Thread
inch
mm
(L)
Y inch
mm
inch
mm
Weight lbs
g
1/4
0.75
19
0.75
19
2.09
53
0.13
60
1/4
0.75
19
0.75
19
2.13
54
0.15
70
1/4
0.75
19
0.67
17
2.20
56
0.14
65
1/4
0.75
19
0.67
17
2.20
56
0.14
65
3/8
0.87
22
0.75
19
2.44
62
0.20
90
3/8
0.87
22
0.75
19
2.44
62
0.23
105
3/8
0.87
22
0.75
19
2.44
62
0.24
110
1/2
1.06
27
0.87
22
2.64
67
0.34
155
1/2
1.06
27
0.87
22
2.76
70
0.33
150
3/4
1.42
36
1.18
30
3.54
90
0.79
360
3/4
1.42
36
1.18
30
3.19
81
0.74
335
1
1.61
41
1.42
36
3.66
93
1.15
520
1
1.61
41
1.42
36
3.62
92
1.07
485
1 1/2
2.17
55
1.97
50
5.04
128
2.28
1,035
2
2.76
70
2.56
65
6.26
159
4.08
1,850
Thread
inch
mm
(L)
H
X inch
mm
inch
mm
Weight lbs
g
1/4
0.75
19
0.94
24
3.03
77
0.17
75
1/4
0.75
19
0.94
24
3.03
77
0.17
75
H
G
。
30
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
CR9
(L) 。
30
H
X F
。
30
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
Catalog Number
GA04CR9 GB04CR9 GA06CR9 UF06CR9 UG06CR9 UF08CR9 UG08CR9 GB12CR9 UG12CR9 UG16CR9 EC24CR9 EC32CR9
X Thread
mm
(L)
H inch
mm
inch
mm
Weight lbs
g
1/4
0.75
19
0.94
24
2.36
60
0.15
1/4
0.75
19
0.94
24
2.36
60
0.15
70
3/8
0.87
22
1.50
38
2.64
67
0.25
115
3/8
0.87
22
1.50
38
2.64
67
0.29
130
3/8
0.87
22
1.50
38
2.76
70
0.30
135
1/2
1.06
27
1.81
46
3.39
86
0.46
210
1/2
1.06
27
1.81
46
3.50
89
0.45
205
3/4
1.42
36
2.36
60
4.02
102
0.97
440
3/4
1.42
36
2.36
60
3.66
93
0.91
415
1
1.61
41
2.76
70
4.65
118
1.49
675
1 1/2
2.17
55
4.13
105
7.24
184
3.13
1,420
2
2.76
70
5.91
150
8.46
215
7.10
3,220
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
48
inch
70
S
5 4 . ~ 4 4 9 . 3
A
Catalog Number 2.79~2.92
inch
GB12S GB16S EC24S EC32S
A B
mm
(L)
B inch
mm
inch
mm
inch
1.50
38.10 1.255 1.250 31.88 31.75
1.38
35
3.54
1.75
44.45 1.565 1.560 39.75 39.62
1.38
35
2.37
60.32 2.125 2.115 53.98 53.72
1.73
44
2.81
71.42 2.500 2.490 63.50 63.25
1.97
50
~
~
~
~
~
~
~
~
mm
Weight lbs
g
90
0.66
300
3.66
93
0.96
435
4.69
119
1.74
790
150
3.59
1,630
5.91
(L)
Flange Head S CODE 61 Flange
SR9
(L)
A
Catalog Number inch
GB12SR9 GB16SR9
。 90
mm
B inch
(L)
H
mm
inch
mm
inch
mm
Weight lbs
g
1.50
38.10 1.255 1.250 31.88 31.75
2.13
54
3.94
100
0.85
385
1.75
44.45 1.565 1.560 39.75 39.62
2.36
60
4.45
113
1.27
575
~
~
~
~
2 9
. H 2 ~ 9 7 . 2
B A
3.94
~4.45
Flange Head S CODE 61 Flange
H
5 4 . ~ 4 4 9 . 3
A
Catalog Number
2.79~2.92
inch
GB12H GB16H
A B
mm
(L)
B inch
mm
lbs
g
1.62
41.28 1.255 1.250 31.88 31.75
1.38
35
3.54
90
0.69
315
1.87
47.63 1.565 1.560 39.75 39.62
1.50
38
3.82
97
1.06
480
~
~
~
~
inch
mm
inch
mm
Weight
(L)
Flange Head H CODE 62 Flange
HR9
(L)
A
Catalog Number inch
GB12HR9 GB16HR9
。 90
mm
B inch
(L)
H
mm
inch
mm
inch
mm
Weight lbs
g
1.62
41.28 1.255 1.250 31.88 31.75
2.28
58
3.98
101
0.90
410
1.87
47.63 1.565 1.560 39.75 39.62
2.87
73
4.45
113
1.41
640
~
~
~
~
2 9
. H 2 ~ 9 7 . 2
3.94 ~
4.45
B A
Flange Head S CODE 61 Flange
G
Y
G
。 30
A
(L)
Male British Parallel Pipe Thread(BSPP)
Catalog Number
GA04G GB04G GA06G UF06G UF08G GB12G UG12G GB16G
Y Thread
inch
mm
(L)
A inch
mm
inch
mm
Weight lbs
g
1/4
0.67
17
0.51
13
1.97
50
0.10
45
1/4
0.67
17
0.51
13
1.97
50
0.11
50
3/8
0.75
19
0.59
15
2.28
58
0.15
70
3/8
0.75
19
0.59
15
2.24
57
0.20
90
1/2
0.87
22
0.71
18
2.52
64
0.28
125
3/4
1.18
30
0.79
20
2.99
76
0.61
275
3/4
1.18
30
0.79
20
2.99
76
0.55
250
1
1.42
36
0.87
22
3.66
93
0.95
430
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
49
PASSTAGE LINE series
1 Small bending radius Passtage series hose has 30% smaller minimum bending radius than equivalent rubber hose
2 Lightweight Passtage series has 50% lighter weight than equivalent rubber hose.
3 Ap pl ic at ion- sp ecif ic hose s av ai la bl e The AG10 series for machine tools, the PS/PC series for paint sprays, and the WSH series for cleaning machines are available.
4
series available for SPL and KF only
The SELFIT series, now patented in eight countries including Japan, is a line of push-type coupling systems for high-pressure hoses. They do not require a crimping machine. For details, refer to pages 54 to 58 and the “SELFIT” catalog.
Flexible architecture
KF・KG ●Compatible Fluid Mineral Oil ●Inner Tube Polyester ●Outer Cover Polyurethane ● Temperature Range: fluid
-40 ℃ to 100℃ / -40°F to 212°F ● Temperature Range : ambient -40 ℃ to 70℃ / -40°F to 158°F
Catalog Number
KF04 KF06 KF08 KF12 KG06 KG08
I.D. inch
1/4 3/8 1/2 3/4 3/8 1/2
mm
O.D. inch mm
6.3 9.5 12.7 19.5 9.5 12.7
0.49 0.65 0.81 1.07 0.68 0.84
Max.W.P. psi MPa
12.4 16.6 20.6 27.3 17.2 21.4
3,000 2,500 2,000 1,300 3,000 3,000
Min.B.P. psi MPa
20.5 12,000 17.0 10,000 14.0 8,000 9.0 5,000 20.5 12,000 20.5 12,000
82.0 68.0 56.0 34.5 82.0 82.0
Min.B.R. inch mm
1.38 1.77 2.56 5.12 2.17 2.56
35 45 65 120 55 65
Weight l bs /f t g /m
0.07 0.11 0.17 0.22 0.13 0.17
110 160 250 330 190 260
Reinforcement
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
JY/50 SY/50
1P SY/50 2P
UX/30 SY/50
If you use a SELFIT FR series coupling with the KF06 hose, the maximum working pressure is 16.0MPa. For details, refer to page 51. Warning Pressurizing the KF06 hose to a working pressure exceeding the maximum could cause it to burst or blow the couplings off. ( In case SELFIT is used) Severe personal injury or death may result if these instructions are not followed.
Small Bending radius
SPL ●Compatible Fluid
Catalog Number
Mineral Oil ●Inner Tube
Polyester ●Outer Cover
Polyurethane ●Temperature Range: fluid -40℃ to 100℃/ -40°F to 212°F ●Temperature Range: ambient -40℃ to 70℃/ -40°F to 158°F
SPL03 SPL04 SPL06 SPL08
inch
I.D. mm
O.D. inch mm
3/16 1/4 3/8 1/2
4.8 6.3 9.5 12.7
0.36 0.42 0.60 0.75
Max.W.P. psi MPa
9.2 10.6 2,000 15.2 19.0 1,500
Min.B.P. psi MPa
14.0 8,000 10.5 6,000
56.0 42.0
Min.B.R. inch mm
0.79 1.38 2.17 2.76
20 35 55 70
Weight l bs /f t g /m
0.03 0.04 0.08 0.11
50 60 120 170
Reinforcement
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
1P 2C
CG/50 JG/50
1P
SG/50
SG/50
One end of an SPL hose can be equipped with a crimped coupling and the other end with a SELFIT coupling. If an SPL hose is equipped with one of the SELFIT FS/FU series couplings, its maximum working pressure will be 10.5MPa, which is different from the pressure Warning specified above. For details, refer to page 54. Pressurizing the SPL hose to a working pressure exceeding the maximum could cause it to burst or blow the couplings off. ( In case SELFIT is used) Severe personal injury or death may result if these instructions are not followed.
KA/KB ●Compatible Fluid
Catalog Number
Mineral Oil ●Inner Tube
Nylon 12 ●Outer Cover
Polyurethane ●Temperature Range: fluid -40℃ to 100 ℃/
-40°F to 212°F ●Temperature Range : ambient -40℃ to 70℃/
-40°F to 158°F
KA02 KA03 KA04 KA05 KA06 KA08 KA12 KB03 KB04 KB05 KB06 KB08 KB12 KB16
I.D.
O.D.
Max.W.P. MPa
inch
mm
inch
mm
psi
1/8 3/16 1/4 5/16 3/8 1/2 3/4 3/16 1/4 5/16 3/8 1/2 3/4 1
3.2 4.8 6.3 7.9 9.5 12.7 19.0 4.8 6.3 7.9 9.5 12.7 19.0 25.4
0.31 0.38 0.46 0.54 0.61 0.77 1.04 0.43 0.51 0.59 0.67 0.83 1.09 1.41
7.9 9.6 11.7 13.7 15.6 19.6 26.3 10.8 12.9 14.9 16.9 21.0 27.8 35.7
2,800 2,200 2,100 1,700 1,500 1,500 700 3,700 3,200 3,000 2,500 2,300 1,400 1,100
19.5 15.0 14.5 12.0 10.5 10.5 5.0 25.5 22.0 20.5 17.0 16.0 9.5 7.5
Min.B.P. MPa
psi
Min.B.R. mm
inch
11,200 78.0 0.47 9,000 61.5 1.38 8,400 58.0 1.77 6,800 48.0 2.36 6,000 42.0 2.76 6,000 42.0 4.13 3,000 20.5 9.06 15,000 103.0 1.38 12,800 88.0 1.77 12,000 82.0 2.36 10,000 68.0 2.76 9,500 65.5 4.13 5,600 38.0 9.06 4,400 30.0 11.42
12 35 45 60 70 105 230 35 45 60 70 105 230 290
Weight g /m
l bs /f t
0.03 0.05 0.06 0.07 0.09 0.13 0.19 0.06 0.08 0.09 0.11 0.15 0.23 0.35
50 70 90 110 140 190 280 90 120 140 170 230 340 520
Reinforcement
SY/50 SY/50 CY/50 CY/50 JY/50 SY(UL)/50(30)
50
ー
1P SY/50
(UL)/50 SY
UX/30 CY/50 CY/50 JY/50 SY(UL)/50(30) ー
2P SY/50 1P
■KB03 to KB12 are equivalent to ISO 3949 type R7 and SAE 100R7 hoses. ■KG06 and KG08 are equivalent to SAE 100R18 hoses.
Reinforcing
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
SY(UL)/50(30) UX/30
Special Application Resin Hoses
Resin Hoses For Machine Tools
● Temperature Range: fluid / −40°C to 93°C / −40°F to 199.4°F ● Recommended Temperature Range: ambient /−40°C to 70°C /
● Compatible Fluid / Mineral Hydraulic Oil ● Inner Tube / Polyurethane ● Outer cover / Soft steel wire 1 braid
−40°F to 158°F
AG10 Catalog Number
AG1004 AG1006 AG1008
I.D. inch
mm
O.D. inch mm
6.3 9.5 12.7
0.46 0.62 0.78
1/4 3/8 1/2
Max.W.P. psi MPa
11.8 15.7 1,500 19.8
Min.B.P. psi MPa
10.5 6,000
42.0
Min.B.R. inch mm
1.38 2.17 2.76
35 55 70
Weight lb s/ ft g /m
0.11 0.15 0.24
160 230 350
Reinforcement
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
JG/50 1P
SG/50
SG/50
● Temperature Range: fluid / -20℃ to 80℃/ -4°F to 176°F ● Compatible Fluid / Organic Solvent ● Temperature Range : ambient / -20℃ to 40℃/ -4°F to 104°F ● Inner Tube / Nylon 12 ● Outer Cover / Polyurethane(PC), Soft Vinyl Chloride(PS)
PS For Paint Spray PS Catalog Number
PS03 PS04 PS05
I.D. inch
mm
3/16 1/4 5/16
4.8 6.3 7.9
O.D. inch mm
0.39 0.47 0.57
Max.W.P. psi MPa
10.0 4,500 12.0 4,000 14.6 3,600
Min.B.P. psi MPa
31.0 13,500 27.5 12,000 24.5 10,800
93.0 82.5 73.5
Min.B.R. inch mm
1.38 1.77 2.36
0.08 0.11 0.13
120 160 200
Reinforcement
Compatible coupling/relevant page Factory-assembled
CY/50 JY/50 SY/50
1W
(Stainless)
● Temperature Range: fluid / −40°C to 93°C / −40°F to 199.4°F ● Recommended Temperature Range: ambient / −40°C to 70°C/
● Compatible Fluid / Water ● Inner Tube / Special resin ● Outer cover / Polyurethane (red)
WSH For Cleaning
35 45 60
Weight lb s/ ft g /m
−40°F to 158°F
WSH Catalog Number
WSH04 WSH06
I.D. inch
mm
1/4 3/8
6.3 9.5
O.D. inch mm
0.50 0.69
JC 70 For Hydraulic Jack
Max.W.P. psi MPa
12.8 2,000 17.4
Min.B.P. psi MPa
14.0 6,000
42.0
Min.B.R. inch mm
Weight lb s/ ft g /m
1.38 2.17
0.07 0.11
35 55
100 170
Reinforcement
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
JY/50 UY/50
1P
SY/50 UY/50
● Temperature Range: fluid / -40°C to 70°C / -40°F to 158°F ● Temperature Range : ambient / -40°C to 70°C / -40°F to 158°F
● Compatible Fluid / Mineral Oil ● Inner Tube / Nylon 12 ● Outer Cover / Polyurethane(Color:Orange)
JC70 Catalog Number
JC7003
I.D. inch
mm
3/16
4.8
O.D. inch mm
0.52
Max.W.P. psi MPa
13.1 9,900
Min.B.P. psi MPa
68.6 20,000 137.2
Min.B.R. inch mm
2.76
70
Weight lb s/ ft g /m
0.09
130
Reinforcement
Compatible coupling/relevant page Factory-assembled
3P
CW/50
■Hoses for hydraulic jacks also include the PrimoLine series hoses, which are available in different sizes than those specified above. (Pages 59 to 63) ■JC7003 has excellent electrical insulation properties.
● Temperature Range: fluid / -40°C to 70°C / -40°F to 158°F ● Temperature Range : ambient / -40°C to 70°C / -40°F to 158°F
● Compatible Fluid / Mineral Oil ● Inner Tube / Nylon 12 ● Outer Cover / Polyurethane(Color:Orange)
SF For Steam SF
2.0MPa
Catalog Number
SF04 SF06 SF08 SF10
I.D. inch
1/4 3/8 1/2 5/8
mm
O.D. inch mm
6.3 9.5 12.7 15.9
0.39 0.54 0.65 0.79
9.9 13.6 16.4 20.1
Max.W.P. psi MPa
Min.B.P. psi MPa
8,000 300
56.0
2.0 6,000
42.0
4,000
28.0
Min.B.R. inch mm
2.56 3.94 5.32 6.69
65 100 135 170
Weight lb s/ ft g /m
0.07 0.11 0.14 0.19
110 170 210 280
Reinforcement
1W
(Stainless)
Compatible coupling/relevant page Factory-assembled UNICRIMP-crimped
JG/50 SG/50 SH/50
SG/50 SH/50 -
*SF hoses can handle steam as well as fluid. When using them for liquid, contact us for information about the temperature range and working pressure.
51
Couplings
CY / CW / JG / JY / SG / SH / SY / UY series
R
Catalog Number
R
Y(HEX)
A (L)
Male British Tapered Pipe Thread(BSPT)
F
SY02R CY0304R CW0306R JG04R JY04R SG04R SY04R SY0506R SG06R SY06R UY06R SG08R SH08R SY08R SH1012R SY12R SH1416R SY16R
Catalog Number
R
Y(HEX)
A (L)
Male British Tapered Pipe Thread(BSPT)
SY02F CG0304F CY0304F JG04F JY04F SG04F SY04F SY0506F SG06F SY06F UY06F SG08F SH08F SY08F SH1012F SY12F SH1416F SY16F
Y Thread 1/8 1/4 3/8 1/4 1/4 1/4 1/4 3/8 3/8 3/8 3/8 1/2 1/2 1/2 3/4 3/4 1 1
0.55 0.75 0.87 0.67 0.67 0.67 0.67 0.75 0.75 0.75 0.75 0.87 0.87 0.87 1.26 1.18 1.42 1.42
mm
14 17 22 17 17 17 17 19 19 19 19 22 22 22 32 30 36 36
1/8 1/4 1/4 1/4 1/4 1/4 1/4 3/8 3/8 3/8 3/8 1/2 1/2 1/2 3/4 3/4 1 1
inch
0.55 0.75 0.75 0.75 0.75 0.75 0.75 0.87 0.87 0.87 0.87 1.06 1.06 1.06 1.42 1.42 1.61 1.61
mm
14 19 19 19 19 19 19 22 22 22 22 27 27 27 36 36 41 41
(L)
A inch
0.39 0.51 0.59 0.51 0.51 0.51 0.51 0.59 0.59 0.59 0.59 0.71 0.71 0.71 0.79 0.79 0.87 0.87
X Thread
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
52
inch
mm
10 13 15 13 13 13 13 15 15 15 15 18 18 18 20 20 22 22
inch
1.46 1.77 2.36 1.85 1.89 1.85 1.89 2.52 2.40 2.52 2.52 2.87 2.87 2.87 2.83 2.91 2.91 3.50
0.55 0.75 0.75 0.75 0.75 0.75 0.75 0.87 0.87 0.87 0.75 1.06 1.06 1.06 1.42 1.42 1.61 1.61
mm
14 17 17 17 17 17 17 17 19 19 19 22 22 22 32 30 36 36
37 45 60 47 48 47 48 64 61 64 64 73 73 73 72 74 74 89
Weight lbs
inch
1.69 2.09 1.97 2.09 2.13 2.09 2.13 2.36 2.56 2.68 2.68 2.87 2.87 2.99 3.03 3.11 3.15 3.74
mm
43 53 50 53 54 53 54 60 65 68 68 73 73 76 77 79 80 95
g
0.03 0.09 0.11 0.08 0.10 0.09 0.10 0.14 0.15 0.19 0.19 0.25 0.26 0.31 0.36 0.51 0.47 0.82
(L)
Y inch
mm
15 40 50 35 45 40 45 65 70 85 85 115 120 140 165 230 215 370
Weight lbs
0.06 0.10 0.11 0.12 0.13 0.12 0.13 0.17 0.19 0.22 0.22 0.30 0.31 0.35 0.53 0.63 0.64 0.99
g
25 45 50 55 60 55 60 75 85 100 100 135 140 160 240 285 290 450
C
Catalog Number
X Y
G
。 30 (L)
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
(L)
CR4
。 45 X H
G
。 30
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
(L)
CR9 。 30
H
X F 。 30
SY02C CG0304C CY0304CH17 SG0304C JG04C JY04C SG04C SY04C SY0506C SG06C SY06C UY06C SG08C SH08C SY08C SY12C SY16C
Catalog Number
CG0304CR4 JG04CR4 JY04CR4 SY04CR4 SG06CR4 SY06CR4 SY08CR4C6
Catalog Number
CG0304CR9 JG04CR9 JY04CR9 SG04CR9 SY04CR9 SG06CR9 SY06CR9 SY08CR9C6 SG08CR9N46CJ
Female British Parallel Pipe Thread Male 30°Seat(BSPOR)
X (opposing hexagon sides)
C1
NPSM
Y (opposing hexagon sides)
Catalog Number
CY0304C1 JY04C1 SY04C1 SY0506C1
30°
X Thread 1/8 1/4 1/4 1/4 1/4 1/4 1/4 1/4 3/8 3/8 3/8 3/8 1/2 1/2 1/2 3/4 1
inch
0.55 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.87 0.87 0.87 0.87 1.06 1.06 1.06 1.42 1.42
mm
14 19 19 19 19 19 19 19 22 22 22 22 27 27 27 36 41
0.55 0.75 0.67 0.67 0.67 0.67 0.67 0.67 0.67 0.75 0.75 0.75 0.87 0.87 0.87 1.18 1.42
1/4 1/4 1/4 1/4 3/8 3/8 1/2
inch
0.75 0.75 0.75 0.75 0.87 0.87 1.06
mm
19 19 19 19 22 22 27
inch
0.94 0.94 0.94 0.94 1.02 1.02 0.87
1/4 1/4 1/4 1/4 1/4 3/8 3/8 1/2 1/2
inch
0.75 0.75 0.75 0.75 0.75 0.87 0.87 1.06 1.06
mm
19 19 19 19 19 22 22 27 27
inch
0.94 0.94 0.94 0.94 0.94 1.50 1.50 1.81 1.81
X Thread 1/4 1/4 1/4 3/8
inch
0.75 0.75 0.75 0.87
mm
19 19 19 22
14 17 17 17 17 17 17 17 17 19 19 19 22 22 22 30 36
inch
1.65 1.97 2.09 1.97 2.09 2.13 2.05 2.13 2.32 2.56 2.68 2.68 2.87 2.87 2.99 3.23 3.74
mm
24 24 24 24 26 26 22
mm
24 24 24 24 24 38 38 46 46
2.72 2.87 2.60 2.60 4.29 3.66 5.16
0.75 0.67 0.67 0.67
mm
17 17 17 17
42 50 53 50 53 54 52 54 59 65 68 68 73 73 76 82 95
Weight lbs
mm
69 73 66 66 109 93 131
2.05 2.20 2.28 2.20 2.28 2.76 2.87 4.13 4.13
mm
52 56 58 56 58 70 73 105 105
2.01 2.13 2.13 2.32
mm
51 54 54 59
25 45 50 50 55 60 55 60 75 90 100 100 140 145 165 295 440
Weight lbs
g
0.12 0.14 0.15 0.15 0.25 0.29 0.51
55 65 70 70 115 130 230
Weight lbs
g
0.11 0.13 0.14 0.13 0.14 0.25 0.29 0.51 0.44
50 60 65 60 65 115 130 230 200
(L) inch
g
0.06 0.10 0.11 0.11 0.12 0.13 0.12 0.13 0.17 0.20 0.22 0.22 0.31 0.32 0.36 0.65 0.97
(L) inch
Y inch
mm
(L) inch
H
X Thread
mm
H
X Thread
(L)
Y inch
Weight lbs
0.11 0.13 0.13 0.17
g
50 60 60 75
(L)
Male American Parallel Pipe Thread Male 30º Seat
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
53
FT FS FU series
FR series
●Compatible fluid Mineral Oil
●Compatible Fluid Mineral Oil
●Inner Tube (SPL) Polyester
●Inner Tube (SPL) Polyester
●Outer Cover (SPL) Polyurethane
●Outer Cover (SPL) Polyurethane
●Temperature Range : fluid
●Temperature Range : fluid
●Temperature Range : ambient
●Temperature Range : ambient -30℃ to +70℃/ -22° F to +158° F
・
・
*1 -30℃ to +80℃ / -22° F to +176° F
1
Repair on-site
2
No crimpers required
3
Easy piping work in Iimited area
4
No external power source required
-30℃ to +100℃/ -22° F to +212° F *2
-30℃ to +70℃ / - 22° F to +158° F
*1 You can use the SPL02 at 100°C / 212°F. If you use couplings FT04, FT06, or FT08 at 100°C / 212°F, the maximum working pressure is 10.5MPa. *2 Note that the figure is different from those for KF series hoses assembled with crimping-type couplings.
Applicable hose
SPL Maximum Working Pressure
I.D.
Catalog Number
10.5-20.5MPa
inch
SPL02 SPL04 SPL06 SPL08
1,500-3,000PSI
1/8 1/4 3/8 1/2
mm
O.D. inch mm
3.2 6.3 9.5 12.7
0.31 0.42 0.60 0.74
FT Max.W.D. psi MPa
FS FU Max.W.D. ・
psi
MPa
− 7.9 3,000 20.5 *3 − 10.6 2,000 14.0 15.2 1,500 10.5 18.9 1,500 10.5
Min.B.P. psi MPa
Min.B.R. inch mm
12,000
82.0
8,000
56.0
6,000
42.0
0.47 1.38 2.17 2.76
Weight lb s/ ft g /m
12 35 55 70
0.03 0.04 0.08 0.11
Reinforcement
50 60 120 170
1P 2C 1P
*3 The SPL02 can withstand a maximum shock pressure of 27.5MPa. For other hoses, do not exceed the maximum working pressure. ●The SPL02 and the other hoses have survived impulse testing performed 400,000 times using a flat waveform and a maximum shock pressure of 27.5MPa for SPL02, and under the maximum working pressure for the other hoses.●Be careful when using the FS or FU series of Bridgestone SELFIT couplings. ●SPL series cut hoses are also available. They are SPL02/04/06 (20m hose: SPLXX-20, 100m hose: SPLXX-100) and the SPL08 (10m hose: SPL08-10, 50m hose: SPL08-50).●Hoses and fittings cannot be recycled. One end of an SPL hose can be equipped with a crimped coupling and the other end with a SELFIT coupling. The maximum working pressure and the minimum burst pressure for an Warning SPL hose with these couplings are as specified above. Pressurizing this SPL hose to a working pressure exceeding the maximum could cause it to burst or blow the couplings off. Severe personal injury or death may result if these instructions are not followed.
Couplings
R
FT series[for only SPL]
(PT) R
Catalog Number Y1(HEX)
Y2(DODEC) L
Y2
Male British Tapered Pipe Thread(BSPT)
F
Y1
FT02R FT04R FT06R FT08R
30° G
(PF)
Y3 L
Y2
FT02F FT04F FT06F FT08F
Thread
inch
1/8 1/4 3/8 1/2
0.55
G
φD
L
Female Japanese Industrial Pipe Thread (JIS) Female 30°Seat
Reinforcing
54
0.55 0.67 0.87 1.06
mm
inch
14 17 22 27
14 0.55
−
−
−
−
−
−
−
−
−
mm
mm
0.55 0.67 0.87 1.06
Y2 inch
(L)
Y2
mm
Y1
30°
(PF) Y3(HEX)
inch
1/8 1/4 3/8 1/2
Catalog Number
Y2
Y1 Thread
inch
14 17 22 27
1.81 1.85 2.28 2.64
14 0.55 − 0.75 − 0.87 − 1.06
mm
14 − 19 0.75 22 0.94 27 1.18
mm
g
0.08 0.11 0.20 0.35
(L)
D inch
Weight lbs
46 47 58 67
*4
Y3 inch
mm
inch
mm
− 2.05
52 53 62 70
19 2.09 24 2.44 30 2.85
35 50 90 160
Weight lbs
g
0.09 40 0.17 75 0.24 110 0.44 200
Couplings
R
FS・FU series[for only SPL]
(PT) R
Catalog Number Y1(HEX)
Y2(DODEC)
FS04R FS06R FS08R
C
L
Y2
Y1
Y2
(L)
C
Weight
Thread
inch
mm
inch
mm
inch
mm
inch
mm
lbs
g
1/4 3/8 1/2
0.67 0.87 1.06
17 22 27
0.67 0.87 1.06
17 22 27
0.39 0.47 0.51
10 12 13
2.24 2.76 3.15
57 70 80
0.11 0.21 0.40
50 95 180
Thread
inch
mm
inch
mm
inch
mm
inch
mm
lbs
g
1/4 3/8 1/2
0.75 0.94 1.18
19 24 30
0.75 0.87 1.06
19 22 27
0.39 0.47 0.51
10 12 13
2.48 2.91 3.23
63 74 82
0.17 0.25 0.45
75 115 205
Male British Tapered Pipe Thread(BSPT)
F
Catalog Number
30°
G
Y(opposing hexagon sides) L
(PF)
FU04R FU06R FU08R
C
φD
Y
D
(L)
C
Weight
Female Japanese Industrial Pipe Thread (JIS) Female 30°Seat
■Adapters G ( PF )
30°
( PT) R
Catalog Number
Thread
Weight lbs
g
0.07
30
8021RG02H14
1/8
8021RG04
1/4
0.11
50
8021RG06
3/8
0.22
100
8021RG08
1/2
0.35
160
45°
(PT) R
Catalog Number
(PF) G
30°
Thread
Weight lbs
g
0.07
30 50
8023RG02H14
1/8
8023RG04
1/4
0.11
8023RG06
3/8
0.18
80
0.26
120
8023RG08
1/2
55
Features of the FT, FS, FU, and FR Series
These series of couplings have made innovative changes to the conventional coupling assembly process.
1. Crimping process eliminated ─── save labor and energy Bridgestone SELFIT
Conventional
You can assemble the hose simply by inserting it into the coupling.
*Except the FR series Socket wrench
You can easily assemble the hose by yourself.
You use a machineto crimp thecoupling.
An assembly company or a person familiar with a crimping machine is responsible for crimping the couplings.
Installing only the couplings is impossible.
You can attach hoses in areas with limited space.
You can attach a hose after simply installing the coupling.
You cannot install hoses in areas with limited space.
Crimping machine not required
2. Easy piping ── optimal for field adjustment Bridgestone SELFIT
Conventional
Bridgestone SELFIT
Conventional
You can use an impact wrench to install the R type couplings.
You cannot use an impact wrench or a socket wrench.
The couplings can rotate when no pressure is applied.
You have to tighten the intermediate hex nut with a wrench to prevent the hose from twisting.
※Except the FR series.
You can install the hose without worrying about twists. You can easily detach the couplings from the equipment.
To tighten the nut
Bridgestone SELFIT
Conventional
Bridgestone SELFIT
Conventional
You can install the hose by tightening two parts.
You need to tighten at least three parts. One or more adapters are required.
You can install the hose after fixing the couplings to the equipment or after inserting the hose into the couplings.
You can install the hose only after crimping the couplings.
No adapter is required.
58
Ultra high pressure hose
●Only Hose Assembly Available
JAT and JAM series
The JAT and JAM series are intended for use with water jets—ultra-high pressure hoses—which have been attracting attention recently. The minimum burst pressure is 650MPa for the JAT series and 490 to 588 MPa for the JAM series.
JAL series
The JAL series is intended mainly for use with jacks and high-pressure cleaning tools. They offer high flexibility and working efficiency.
JAK and JKY series
The JAT and JAM series are intended mainly for use with jacks. The unique reinforcing used in their structure makes them flexible. They are lightweight hoses, weighing about half the weight of a conventional hose. With the outer diameter and the bending radius 20% to 30% smaller than those of our other products, these are very easy to use.
■Safety Measures Bore Hose
Safety chain
Safety net
B ore Hose
05
JAT03 80SAF16CL162 8XND10X600
03
JAM03 80SAF14CL162 JAL03 JAL04
04
JAK04
Snap hook: 8ZGB6G (sold separately)
Safety net
JAM05 80SAF17CL162
8XND13X810
JAL06
−
Snap hook: 8ZGB8G (sold separately)
JAK06
−
JAL08
−
JAK08
−
06
−
The safety nets cannot be installed after hose joint 80SAF13CL162 assembly. (They cannot be sold separately.) −
Safet y chain
08
JKY04
−
10
JAL10
−
JAL05
−
12
JAL12
−
JAK05
−
16
JAL16
−
05
The safety nets for 22 hex or smaller nuts can be installed after hose joint assembly. (The safety nets can be sold separately.)
Safety chain
Safety net
8XND22X1120 Snap hook: 8ZGB11G (sold separately) The safety nets for 36 hex or smaller nuts can be installed after hose joint assembly. (The safety nets can be sold separately.)
Snap hook
This hole is basically intended to easily detect small amounts of leakage. Because the liquid dripping from this hole looks like a teardrop, this hole is called a teardrop hole. If actions such as tightening or replacing parts are not taken when a small amount of leakage is detected, the leakage may increase, resulting in liquid ejection. Liquid (water) ejected from the seat may fill joint and the liquid pressure may cause the joint to swell, damaging the joint (threaded part and hex nut). Finally, the joint may detach from the hose. To prevent this problem, the safety hole performs the function of checking for small amounts of leakage. In addition, it allows liquid to escape from the joint, decreasing the pressure and thus preventing the joint (coupling) from detaching from the hose in the case that ejected liquid fills the joint.
■Maximum Working Pressure for the Joint (Bridgestone PrimoLine) Unit: MPa
Size Joint type
R Q、 G G4・C5 J4 J5
*1 *2
*3
04 98.0 196.0
06 68.5 127.5
ー ー ー
ー ー ー
08 68.5 98.0 294.0 245.0 294.5
12 68.5 88.0
16 68.5 68.5
ー ー ー
ー ー ー
*1:The maximum pressure for the ultra high pressure G joint is different from that for the ordinary high-pressure G joint. *2:Only a 30 hex nut can be used for a C5 joint at 294.0MPa (JAT05). (A 27 hex nut can be used for pressures of 245.0MPa or lower.) *3:Only a titanium-alloy core can be used for a J4 joint at 294.0MPa (JAT03). For a steel or SUS630 core, a joint rated at 245.0MPa can be used.
■Tightening Torques (for Bridgestone PrimoLine) For information about the tightening conditions, refer to page 82. Size Joint type *1 ( reference values )
R Q、 G G4・C5 J4 J5
Unit: N・m
04
06
08
12
16
30 37
40 74
180 132
300 196
ー ー ー
ー ー ー
70 88 98 39 49
ー ー ー
ー ー ー
1:Use the tightening torques shown in the table on the left when tightening joints. (The torque tolerance for coupling joints is ±10%.) 2:Use these tightening torques when the following conditions coexist: - There is no oil left on either the threaded part or the inside of the nut. - The core hex nut is tightened with a wrench to prevent the coupling from rotating. For information about other tightening torques, contact us. *1:The tightening torque for the R joint varies depending on how its sealing tape is wrapped. Therefore, the values shown in the table are for reference only.
59
For water Jet application ●Compatible fluid / Mineral hydraulic Oil, Water ●Inner Tube / Special plastics ●Outer Cover / Nylon 12 ●Temperature Range : fluid
-40℃ to +50℃ (-40° F to +12 2° F)(Mineral Oil ) / 0℃ to +50℃ (32 ° F to + 122° F)( Wat er)
●Temperature Range : ambient -40℃ to +50℃ / -40° F to +122° F
JAT/JAM I.D.
Catalog Number
inch
JAT03 JAM03 JAM05
O.D. inch mm
mm
3/16 3/16 5/16
5.0 5.0 8.0
0.61 0.54 0.69
Max.W.P. psi MPa
Min.B.P. psi MPa
Min.B.R. inch mm
15.6 43,000 294.0 94,500 650.0 13.7 35,500 245.0 85,500 588.0 17.6 35,500 245.0 71,000 490.0
15.7 5.91 7.48
Weight l bs /f t g/ m
400 150 190
1.48 1.06 1.66
Reinforcement
670 480 750
Compatible coupling/relevant page Factory-assembled
8S
BN
6S
BX
*The standard color for the JAM05 outer cover is gray. Use a pressure waveform (jack waveform) that can withstand shock pressure.
Couplings
Materials: SS or SC equivalent steel Surface: Zinc plating or chromate treatment
G4 type
G4 C5
M
A
Catalog Number
M22×1.5
BX0508G4
X(HEX)
M
φ3×2
(L)
Thread
BX0308G4
C5 type
Y(HEX)
C
A
(L)
(Safety Hole)
(L)
A
Y
Weight
Catalog Number
g
inch mm inch mm inch mm
lbs
0.87
22
0.71 18
3.11
79
0.39 175
BX0308C5
0.94
24
0.71 18
3.42
87
0.49 220
BX0508C5
Y(HEX)×(Duplex)
X
Thread
A
Y
C
(L)
Weight
inch mm inch mm inch mm inch mm inch mm lbs M22×1.5
g
1.06 27 0.55 14 1.02 26 0.28
7 3.50 89 0.43 195
1.06 27 0.55 14 1.02 26 0.28
7 3.86 98 1.85 245
BI couplers (easily attachable/detachable joints) are available for the couplings above. Refer to the BI coupler catalog. 245.0MPa coupling [Catalog number: 30JA04G4M4-SKFZ]
J5 J4
J5/J4 type
enlarged
UNF・M
A 7mm
8mm
~
Y(HEX)
B
Catalog Number BN0308J5X107
(L)
*Set the sleeve at the first or second thread from the top ( approx 7mm )
BX0308J5 BX0508J4
Thread
UNF 3/4-16
Y
A
B
(L)
Weight
inch mm inch mm inch mm inch mm lbs
g
0.86 22 0.59 15 1.50 38 3.90
99 0.40 180
0.86 22 0.59 15 1.50 38 3.90
99 0.43 195
M22×1.5 0.86 22 0.63 16
1.50 38 4.25 107 0.55 250
*For water use , special alloy is recommended because of stronger resistance against corrosion. *BN0308J5X107 is only available for special alloy.
Reinforcing
60
For Hydraulic Jack application ●Compatible fluid / Mineral hydraulic Oil, Water ●Inner Tube / Special plastics(JAL03~05), Nylon 12(JAL06~16) ●Outer Cover / Nylon 12 ●Temperature Range : fluid
-40℃ to +50℃ (-40° F to +122 ° F)(Mineral O il) / 0℃ to +5 0℃ (32° F to +122 ° F)( Wat er)
●Temperature Range : ambient -40℃ to +50℃ / -40° F to +122° F
JAL I.D.
Catalog Number
JAL03 JAL04 JAL05 JAL06 JAL08 JAL10 JAL12 JAL16
inch
mm
O.D. inch mm
3/16 1/4 5/16 3/8 1/2 5/8 3/4 1
5.0 6.3 8.0 9.8 12.8 16.3 20.0 25.0
0.44 0.50 0.60 0.71 0.83 0.98 1.15 1.42
Max.W.P. psi MPa
11.1 12.6 15.2 18.0 21.0 25.0 29.2 36.0
28,500 21,500 18,500 17,000 14,000 13,000 10,500 10,000
196.0 147.0 127.5 117.5 98.0 88.0 73.5 68.5
Min.B.P. psi MPa
57,000 45,500 42,500 37,000 34,000 31,000 25,500 21,500
Min.B.R. inch mm
392.0 4.53 313.5 5.71 294.0 6.50 255.0 6.69 235.0 7.48 215.0 8.27 176.5 9.45 147.0 11.02
Weight lb s/ ft g /m
115 145 165 170 190 210 240 280
Reinforcement
0.57 260 0.64 290 0.84 380 1.21 550 1.57 710 2.31 1,050 2.56 1,160 3.33 1,510
Compatible coupling/relevant page Factory-assembled
BL BK AK
4S
AL
*Use a pressure waveform (jack waveform) that can withstand shock pressure.
Couplings
Materials: SS or SC equivalent steel Surface: Zinc plating or chromate treatment
G/G4 R4 Q
G or M
Q type
R type
G/G4 type Y(HEX)
BL0304Q、BL04Q BK0506Q
Y(HEX)
R
R
(HEX) G Y
G
Y(HEX)
R φd×2
A
A
(L)
Catalog Number
A
(L)
Y
Thread
(L)
A
inch mm inch mm inch mm
Weight
lbs
g
Y
(Safety Hole)
A
(L)
C
(L)
C
φd
Weight
inch mm inch mm inch mm inch mm inch mm lbs
g
1/4
0.75
19 0.39 10 2.80
71 0.22 5.5 0.08 2.0 0.21
BL04Q
1/4
0.75
19 0.39 10 2.91
74 0.22 5.5 0.08 2.0 0.23 105
BK0506Q
3/8
0.87
22 0.39 10 2.87
73 0.22 5.5 0.10 2.5 0.28 125
110
AK06Q
3/8
0.87
22 0.75 19 2.76
70 0.26 6.7 0.10 2.5 0.31 140
135
AL06Q
3/8
0.87
22 0.75 19 2.76
70 0.26 6.7 0.10 2.5 0.31 140
325
AL08Q
1/2
1.06
27 0.87 22 4.02 102 0.28 7.0 0.12 3.0 0.73 330
1.01
460
AL1012Q
3/4
1.42
36 0.98 25 4.21 107 0.35 9.0 0.14 3.5 0.90 410
110
1.19
540
AL12Q
3/4
1.42
36 1.06 27 4.29 109 0.35 9.0 0.14 3.5 1.23 560
119
1.50
680
AL16Q
1
1.61
41 1.10 28 4.41 112 0.35 9.0 0.14 3.5 1.54 700
0.75
19
0.51
13
2.68
68
0.19
85
M22×1.5
0.87
22
0.71
18
2.91
74
0.30
135
BL04G
G1/4
0.75
19
0.51
13
2.68
68
0.20
90
BK0506R
R3/8
0.87
22
0.59
15
2.72
69
0.24
AK06R
R3/8
0.87
22
0.59
15
2.83
72
0.30
AL08R
R1/2
1.06
27
0.71
18
4.13
105
0.72
AL1012G
G3/4
1.42
36
0.79
20
4.45
113
AL12G
G3/4
1.42
36
0.79
20
4.33
AL16G
G1
1.61
41
0.87
22
4.69
BL0308G4
Thread
A
d×2
BL0304Q
G1/4
BL0304G
Catalog Number
(Safety Hole)
(L)
95
61
For Hydraulic Jack application
●Compatible fluid / Mineral hydraulic Oil ●Inner Tube / Nylon 12 ●Outer Cover / Polyurethane ●Temperature Range : fluid / -40℃ to +80℃(-40° F to +176° F) ●Temperature Range : ambient / -40℃ to +70℃ / -40° F to +158° F
JKY/JAK I.D.
Catalog Number
inch
mm
O.D. inch mm
1/4 1/4 5/16 3/8 1/2
6.3 6.3 8.2 10.0 12.8
0.50 0.51 0.56 0.68 0.80
JKY04 JAK04 JAK05 JAK06 JAK08
Max.W.P. psi MPa
12.7 10,000 13.0 14,000 14.1 10,000 17.3 10,000 20.2 10,000
Min.B.P. psi MPa
68.5 24,000 98.0 35,500 68.5 25,500 68.5 22,500 68.5 21,500
Min.B.R. inch mm
166.5 245.0 176.5 156.5 147.0
2.17 2.17 3.15 3.94 5.12
55 55 80 100 130
Weight l bs /f t g/ m
Reinforcement
Compatible coupling/relevant page Factory-assembled
210 2S+1P 310 320 2S+1W 400 540
0.46 0.68 0.71 0.88 1.19
UY AK BK AK
*Use a pressure waveform (jack waveform) that can withstand shock pressure.
Materials: SS or SC equivalent steel Surface: Zinc plating or chromate treatment
Couplings R type
R Q
Q type
AK04Q AK0406Q BK0506Q
Y(HEX)
R
G
Y(HEX)
R
Y(HEX)
G
R
φd2 A
A
(L)
Catalog Number
Thread
Weight g inch mm inch mm inch mm lbs Y
A
(L)
Catalog Number
(Safety Hole)
(L)
φd2
(Safety Hole)
C
A
( L)
φd Weight Y A C (L) Thread inch mm inch mm inch mm inch mm inch mm lbs g
UY0406R AK04R*
3/8
0.75
19 0.59
15 2.24
57 0.14
65
AK04Q*
1/4
0.75 19 0.39 10 2.60 66
—
—
—
— 0.20
1/4
0.75
19 0.51
13 2.36
60 0.17
75
AK0406Q
3/8
0.87 22 0.39 10 2.64 67
—
—
—
— 0.24 110
AK0406R
3/8
0.87
22 0.59
15 2.48
63 0.20
90
BK0506Q
3/8
0.87 22 0.75 19 2.87 73 0.22 5.5 0.10 2.5 0.28 125
BK0506R
3/8
0.87
22 0.59
15 2.83
72 0.24
110
AK06Q
3/8
0.87 22 0.75 19 2.76 70 0.26 6.7 0.10 2.5 0.31 140
AK06R
3/8
0.87
22 0.59
15 2.83
72 0.30
135
AK08Q
1/2
1.06 27 0.87 22 3.07 78 0.28 7.0 0.12 3.0 0.46 210
AK08R
1/2
27 0.71
18 3.15
80 0.45
205
1.06
*Couplings marked with an asterisk are available on request. Use the 30º female seat type adapter by Bridgestone with the Q type coupling.
◇BI couplers (easily attachable/detachable joints) for AK04R, AK0406R, BK0506R, AK06R, and AK08R are available. Refer to the BI coupler catalog.
68.5MPa couplings
Catalog number. 30JCA06C-XXZ 30JCA04C-XXZ * 30JCA08C-XXZ * *Special products
Reinforcing
62
90
■Connection Method 1
To connect J5 type coupling to equipments
Prepare the equipment side as shown in the figure on the right.
18.0
●Equipment side
1 . 0 ±
BX0308J5 BN0308J5
15.0
1 . 0 ±
0 . 0 0 . . 0 4 8 2
φ φ φ
C1
° 2 1 0
+
—
° 0 3
2 1 5 . S 3
/4 — 16UNF
2
To connect G4 type coupling to equipments
●Equipment side Prepare the equipment side as shown in the figure on the right.
1 . 0 ±
1 . 0 ±
0 2 . . 2 5
φ φ ) ) 0 3 5 0 0
Use Cone
8083
0 . . 1 3 1 2
for connection
BX0308G4 BX0508G4
Cone 8083
18.5 12.0
0 . 3 1
M M A A φ φ J J ° ( 2 ( .
C1
φ
12.0
0
1 +
—
° 0 3
3
1 . 0 ±
21 5 . S
M22�1.5 — 6H
To connect C5 type coupling to equipments
●Equipment side Prepare the equipment side as *Same as 2.To conshown in the figure on the right. Use adapter
8082
for connection
8082
Adapter
27HEX
BX0308C5 BX0508C5
nect G4 type couplings to equipments. 18.0
23.2 51.2
M22�1.5-6g at both end
4
To connect two C5 type couplings BX0308C5 BX0508C5 Use adapter
8081
8081
Adapter
27HEX
BX0308C5 BX0508C5
for connection 18.0
18.0
46.0
M22�1.5-6g at both end
5
To connect two J5 type couplings BN0308J5X107 BX0308J5 Use adapter
8084
Adapter
8084
15.0
15.0
BN0308J5X107 BX0308J5
for connection 50.0
32HEX
3/4-16UNF-2B at both end
6
To connect J4 type coupling to equipments 18.0
●Equipment side Prepare the equipment side as shown in the figure on the right.
1 . 0 ±
1 . 0 ±
0 0 0 . . . 3 5 9 2
φ φ φ
BX0508J4
15.0
C1
° 2 1 0
+
—
° 0 3
2 1 5 . S
M22�1.5 — 6H
G4 and C5 type couplings can be connected directly to each other. Use the Q type coupling equipped with adapter 8002RG○○ under a pressure of 147MPa or
lower. *8022RG ○○ or 8024RG ○○ cannot be used.
◇BI couplers (easily attachable/detachable joints) are available for BL0304Q and BL04Q. Refer to the BI coupler catalog. 147.0MPa coupling [Catalog number: 30JA04B-SKFZ]
63
Adapters ■When using an adapter, take into account the outline dimensions of the assembled adapter below when determining the length of the assembly hose. (For the L dimensions, refer to page 5.)
8001RG Y Y (6角対辺) GG
RR
。 30。 30
AA
BB LL
*Brass
versions are available for the products marked with an asterisk. For their dimensions, refer to the adapter specifications for the ACT series on page 22.
8002RG YY (6角対辺) GG
RR
。 。 30 30
AA
BB LL
8004GG Y Y (6角対辺) GG
GG
。。 3030
。。 3030
AA
BB LL
8005RG GG
RcRc
。 3030。
AA
Y (6角対辺) Y L L
8006RG GG RR
。。 3030
AA
Y Y (6角対辺) LL
Y
L mm
A mm
B mm
Weight g
1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2
14 19 22 27 36 41 50 55 70 90
32 37 41 48 54 58 66 69 76 85
10 13 15 18 20 22 25 25 29 32
14 16 18 20 22 23 27 29 30 34
20 40 60 100 170 240 420 480 720 1,300
Catalog Number
Thread
Y mm
L mm
A mm
B mm
Weight g
8002RG04 8002RG06 8002RG08 8002RG12 8002RG16 8002RG20 8002RG24 8002RG32
1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2
19 22 27 36 41 50 55 70
34 38 46 52 57 64 65 75
13 15 18 20 22 25 25 29
13 15 18 20 22 25 25 29
Catalog Number
Thread
Y mm
L mm
A mm
B mm
8004GG04 8004GG06 8004GG08 8004GG12 8004GG16 8004GG20 8004GG24 8004GG32
1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2
19 22 27 36 41 50 55 70
34 38 46 52 57 64 65 75
13 15 18 20 22 25 25 29
13 15 18 20 22 25 25 29
Catalog Number
Thread
Y mm
L mm
A mm
8005RG04 8005RG06 8005RG08 8005RG12 8005RG16 8005RG20 8005RG24 8005RG32
1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2
19 22 27 36 41 50 55 70
32 37 42 47 51 57 61 65
16 18 20 22 23 27 29 30
Catalog Number
Thread
Y mm
L mm
A mm
Max. W.P
Weight g
8006RG04 8006RG06 8006RG08 8006RG12 8006RG16 8006RG20 8006RG24 8006RG32
1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2
19 22 27 36 41 50 55 70
40 42 49 57 63 71 74 82.8
13 15 18 20 22 25 25 29
34.5 34.5 34.5 27.5 20.5 17.0 10.5 10.5
60 80 130 250 330 500 580 1,040
Catalog Number Thread mm 8001RG02 8001RG04* 8001RG06* 8001RG08* 8001RG12 8001RG16 8001RG20 8001RG24 8001RG32 8001RG40
Standard product — Material: SS or SC equivalent steel, Surface: Zinc plating or chromate treatment
64
40 60 100 170 240 410 470 760 Weight g
40 60 100 170 240 410 470 760 Weight g
40 60 90 180 240 330 400 690
Adapter + Coupling
E
+02F +04F +06F +08F +12F +16F +20F +24F +32F +40F
Adapter + Coupling
EE
+04C +06C +08C +12C +16C +20C +24C +32C
Adapter + Coupling
E E
+04C +06C +08C +12C +16C +20C +24C +32C
Adapter + Coupling
E E
+04F +06F +08F +12F +16F +20F +24F +32F
Adapter + Coupling
E E
+04G +06G +08G +12G +16G +20G +24G +32G
E mm 23 26 29 33 38 42 46 49 52 56 E mm 26 29 35 39 44 47 47 54 E mm 26 29 35 39 44 47 47 54 E mm 21 25 27 31 35 37 41 41 E mm 30 32 37 44 47 53 53 61
Split flanges Split Flange ●8YK**S
: for SAE Standard Pressure Series / bolt thread : UNF
●8YK**H
: for SAE High Pressure Series / bolt thread : UNF
●8YK**SM**
: for SAE Standard Pressure Series / body thread : M
●8YK**HM**
: for SAE High Pressure Series / bolt thread : M
V U F
※1.2
o Q
D J
/
● Figure in [ ] show SAE specification. Though there are some differences
2
Q
in dimension, there are no performance differences.
φT
P
R
● Weight below shows that of 1 set.
※Bores 20 to 32 are 1.5mm for the H type and 1.2mm for the other types.
Note: Split flanges for metric screw threads and for unified screw threads differ only in terms of the T dimensions. Other dimensions and the maximum working pressures for these flanges are the same.
Catalog Number
flange
D mm
F mm
J mm
O mm
P mm
Q mm
R mm
T mm
V mm
Max.W.P.
MPa
Weight g
Catalog Number.
T Weight mm g 9.0
180
200 8YK12SM10
10.8
200
34.5
260 8YK16SM10
10.8
260
11.9 14.3 22.0 27.5 〔14.0〕 50.8 93.8 40.1 69.9 17.0 13.5 19.1 30.0 20.5 〔16.0〕 〔25.0〕 48.0 20.2 19.0 30.0 20.5 62.7 101.6 77.8 13.5 〔47.2 〕 〔21.0〕 〔16.0〕 〔26.0〕
320 8YK20SM12
12.5
320
560 8YK24SM12
12.5
560
720 8YK32SM12
12.5
720
7.24
24.6
56.4
22.6
40.5
8.0
8.7
16.0
22.0
41.0
140 8YK08H
8.7
140
42.1
8.26
32.5
71.4
29.0
50.8
11.0
10.3
19.0
28.0
41.0
320 8YK12HM10
10.5
320
1
48.4
9.02
38.9
81.1
33.8
57.2
13.0
11.9
560 8YK16HM12
12.5
560
8YK20H
1 1/4
54.8
9.78
44.5
95.3
37.6
66.7 14.5 13.5 〔15.0〕
32.0 24.0〔33.0〕 41.0 27.0 34.0 41.0 〔38.0〕
800 8YK20HM12
12.5
800
8YK24H
1 1/2
64.3 12.07
51.6 112.8
46.5
79.4
17.0
16.7
30.0
43.0
41.0 1,280 8YK24HM14
14.9
1,280
8YK32H
2
80.2 12.07
67.6 133.4
55.9
96.8
21.0
19.8
37.0
52.0
41.0 2,140 8YK32HM20
20.9
2,140
8YK08S
1/2
31.0
6.22
24.3
54.0
21.8
38.1
8.0
8YK12S
3/4
38.9
6.22
32.1
65.1
24.9
47.6
8YK16S
1
45.2
7.49
38.5
69.9
28.2
52.4
8YK20S
1 1/4
51.6
7.49
43.7
8YK24S
1 1/2
61.1
7.49
8YK32S
2
72.2
9.02
8YK08H
1/2
32.5
8YK12H
3/4
8YK16H
79.4
35.3
58.7
8.7
U mm
19.0
34.5
180 8YK08S
10.0
14.3 10.3 22.0 〔14.0〕
34.5
12.0
10.3
13.0
16.0
24.0
14.0
Bolt for Split Flange Catalog Number
Bolt Thread : UNF
●8YA**S : for SAE Standard Pressure Series ●8YA**H : for SAE High Pressure Series
UNF D
S
H
Y
R
Washer is included
UNF
Y mm
S mm
mm
D mm
8YK08S 8YK08H
6.0
8YK12S 8YK16S
11.1
7.1
8YK20S
38.1
12.7
7.9
8YK24S 8YK32S
25
38.1
9.52
6.0
8YK12H
15.9
25
44.5
11.1
7.1
8YK16H
/2 -13
19.0
25
44.5
12.7
7.9
8YK20H
8YA24H
5
/8 -11
23.8
32
57.2
15.9
9.9
8YK24H
8YA32H
3
26.8
32
69.8
18.9
11.9
8YK32H
5
/ 16 -18
12.7
25
31.8
7.94
8YA12S
3
/8 -16
14.3
25
31.8
9.52
8YA20S
7
/ 16 -14
15.9
28
38.1
8YA24S
1
/2 -13
19.0
32
8YA12H
3
/8 -16
14.3
8YA16H
7
/ 16 -14
8YA20H
1
/4 -10 M
●8YA**SM** : for SAE Standard Pressure Series
8YA08SM8
M8×1.25
13.0
22.0
30.0
8.0
●8YA**HM** : for SAE High Pressure Series
8YA12SM10 M10×1.5
17.0
26.0
30.0
10.0
8YA20SM12
M12×1.75
19.0
30.0
40.0
12.0
8YA12HM10
M10×1.5
17.0
26.0
40.0
10.0
M D
Y
R
Washer is included
66
Y mm
S mm
mm
D mm
H mm
Split Flange
5.5
8YK08S 8YK08H
7.0
8YK12SM10 8YK16SM10
8.0
8YK20SM12 8YK24SM12 8YK32SM12
7.0
8YK12HM10
8.0
8YK16HM12 8YK20HM12
M12×1.75
19.0
30.0
45.0
12.0
8YA24HM14 M14×2.0
22.0
34.0
55.0
14.0
9.0
8YK24HM14
8YA32HM20 M20×2.5
30.0
46.0
70.0
20.0
13.0
8YK32HM20
8YA16HM12
S
H
Split Flange
5.2
8YA08S
Catalog Number
Bolt Thread : M
H mm
O-ring for Split Flanges ●Materials : NBR r e l l a m S r o A - A 7 0 . 0
・ I D mm
Catalog Number
●Hardness : 90(Durometer A)
A A . I D
section
W 0.12 or Smaller
W mm
SAE J515 or AS568
Split Flange
8YG08S
18.64±0.15
3.53±0.1
210
08S 08H
8YG12S
24.99±0.15
〃
214
12S 12SM10 12H 12HM10
8YG16S
32.92±0.15
〃
219
16S 16SM10 16H 16HM12
222
20S 20H
20SM12 20HM12
225
24S 24H
24SM12 24HM14
228
32S 32SM12 32H 32HM20
8YG20S
37.69±0.15
〃
8YG24S
47.22±0.25
〃
8YG32S
56.74±0.25
〃
、
、
、
、
、
、
、
、
、
、
Flange for JIS 21 MPa Flange for JIS 21MPa
E
4 −φd3
30°
A
1 2 d d
d
B
φ
φ φ
B A
C
73K1 : JIS SHB compliant. 73K3 : JIS SSB compliant.
Bolt for JIS 21 MPa flange
●8YAK (JIS SHA SHB) With nut and washer
●8YBK2 (JIS SSA、 … SSB) With washer
Note) These products cannot be used for loose flanges.
O-ring for JIS 21 MPa flange ●Hardness : 90(Durometer A) ●Materials : NBR r e l l a m S r o
A A
A-A section
1 . 0
W 0.15 or Smaller
. I D
Catalog Number
A mm
73K115 73K315 73K120 73K320 73K125 73K325 73K132 73K332 73K140 73K340 73K150 73K350 73K165 73K365 73K180 73K380
63
40
54
36
68
45
58
40
80
53
68
48
90
63
76
56
100 92
70 65
B C mm mm
112
80
100
73
140
100
128
92
155
112
140
103
Catalog Number
Y (mm)
8YAK15 8YBK215 8YAK25 8YBK225 8YAK40 8YBK240 8YAK65 8YBK265 8YAK80 8YBK280 8YBM10L65S6 8YBM10L70S6 8YBM12L80S6 8YBM12L90S6 8YBM16L110S6 8YBM16L120S6 Catalog Number
17
8YGK15 8YGK20 8YGK25 8YGK32 8YGK40 8YGK50 8YGK65 8YGK80
8 19 10 24 14 30 17 32 17 8 8 10 10 14 14
E mm
d mm
d1 mm
22
11
16.0
22.2
22
12
20.0
27.7
28
14
25.0
34.5
28
16
31.5
43.2
36
18
37.5
49.1
36
20
47.5
61.1
45
22
60
77.1
45
25
71
90
S mm
mm
M10× 1.5
26
60
32
50
M12× 1.75
30
75
36
60
M16× 2
38
95
44
75
M20× 2.5
46
120
52 56
95 130
M
M22× 2.5
50
95
M10× 1.5
32
65
32
70
M12× 1.75
36
80
36 44
90 110
44
120
M16× 2
D mm 10 12 16 20 22 10 12 16
d2 mm
d3 Weight Piping mm g OD 11 530 32 21.7 400 M10×1.5 11 600 38 27.2 450 M10×1.5 13 1,080 45 34.0 760 M12×1.75 13 1,350 56 42.7 M12×1.75 920 18 2,030 63 48.6 M16×2 1,750 18 2,500 75 60.5 M16×2 1,950 22 4,700 76.5 95 M20×2.5 3,600 24 5,900 108 89.4 M22×2.5 4,300 H mm
Split Flange
16
K15 K20 K215 K220 K25 K32 K225 K232 K40 K50 K240 K250
13
K65、 K165
20 14
K265、 K365
22
K280、 K380 K415 K420 K425
7 10
、
8 12 10
10 10 12
K115 K120 K315 K320 K125 K132 K325 K332 K140 K150 K340 K350
、
、 、
、
、
、 、
、
、
、
、
K80、 K180
12 16
K432
16
K450
・ I D mm
W mm
JIS Code
24.4±0.15
3.1±0.1
29.4±0.15
3.1±0.1
34.4±0.15
3.1±0.1
39.4±0.15
3.1±0.1
49.4±0.25
3.1±0.1
59.4±0.25 74.4±0.4
3.1±0.1 3.1±0.1
84.4±0.4
3.1±0.1
B2401-G25 B2401-G30 B2401-G35 B2401-G40 B2401-G50 B2401-G60 B2401-G75 B2401-G85
K440
Split Flange K15、 K215、 K415 K20 、 K220、 K420 K25 、 K225、 K425 K32、 K232、 K432 K40、 K240、 K440 K50、 K250、 K450 K65、 K265、 K465 K80、 K280、 K480
67
BI - Coupler For Safety’s sake
1
Be sure to read the followings before use.
These Bridgestone products are developed for hydraulic components. Follow each product’s application and specification. Avoid burst, leakage and other dangers by following these important steps.
1 Proper use
Warning
Severe personal injury or death may result if these instructions are not followed.
●Do not touch a pressurized coupler or swivel joint. If a product is broken, and a fluid touches the skin, even if no pain is felt, a serious injury including burns may be caused. Obtain medical assistance immediately. Failure to do so can result in the loss of the injured body part or death. Use of plastic hose guards will increase the possibility to protect a person from injury. ●System working pressure should not exceed the rated working pressure. Exceeding the rated working pressure of hose and coupler may result in the hose bursting or hose coupling-blow off. Follow the maximum working pressure ratings listed in this catalog. ●Do not remove BI coupler under pressurized conditions. ●Do not use body or nose of BI coupler as stop valve. ●Do not apply an electrical current to a hose assembly Electrifying may lead to a product failure or electric shock. ●Use compatible hydraulic fluid The use of an incompatible hydraulic fluid will deteriorate the inner tube and or the reinforcement, resulting in the hose bursting or hose coupling blow-off ● Avoid the usage exceeding applicable temperature The usage exceeding applicable temperature may cause leakage and hose coupling blow-off. ● Avoid excessive vibration Excessive vibration may cause leakage and hose coupling blow-off by fatigue.
Caution
Personal injury or property damage may result if these instructions are not followed
●Do not take remaining pressure by hitting head portion of poppet of BI coupler ● Avoid vacuum pressure Excessive vacuum pressure may result in the inner tube damage which will lead to hose failure. ●Never repair or rework. ● Avoid submerging hose assemblies in water or any other liquid,to avoid rust. ●Do not touch with the bare hand, since the BI coupler may get hot.
2 Installation
Caution Follow the below tightening torque. Improper tightening may lead to deterioration of seal performance, oil leakage, and failure of connection portion which may result in injury or material damage.
Please connect a hose at a right angle to the fixed side like (B). Avoid the piping like (A) which may apply too much force on the rotating part.
Housing
Shaft
Fixed Side
① In case of steel or stainless
Size Tightening Torque N・m
04
06
08
12
16
1/4"
3/8"
1/2"
3/4"
1"
25
34
64
132
196
20
24
1 1/4" 1 1/2" 225
255
32 2"
(A)
Swivel Joint
Tightening Torque N・m
Rotation
Fixed Side
06
08
12
16
1/4"
3/8"
1/2"
3/4"
1"
15
25
29
59
88
20
24
1 1/4" 1 1/2" 118
137
32 2" 206
Fixed Side
As for installation of swivel joint, fix the shaft side and rotate the housing side. Do not connect a swivel joint with another swivel joint.
3 Warranty Period Warranty period is impulse cycle number or each specified period, whichever comes earlier .
4 Preventive Maintenance Before every usage, check any leakage from the Products. If found, replace with a new one.
5 Storage F to 104° F) Store in a dark and dry place at the temperature between -10℃ to +40℃(14° 68
(B) OK
Wrong
Rotation
04
Piping or machine side
412
② In case of brass or copper
Size
Fix
Uses
BI couplers for hydraulic/pneumatic hoses are joints that can be easily attached and detached like an electric plug. With these couplings, you can use various attachments with a single pressure source or easily assemble and disassemble a large machine.
Features
Minimize possible fluid leakage and aeration
2
Prevention against hose twisting when unpressurized. Rotate, do not twist.
One simple operation
1
One simple operation to connect and disconnect.
3
Connection in limited working area is possible.
Structure BI coupler is composed of nose, body, collar, and valve frame. When the collar is slid in axial direction, the steel ball can be free and the body and the nose can be inserted. After the insertion, if the collar is moved back, the steel ball is on the line of the nose and BI coupler is locked. In this condition, each poppet is pushed and the circuit is open.For disconnection, when the collar is moved on axal direction, the steelball is free again and body and nose is easily disconnected. At the time, the poppet adheres to seat surface and the circuit is closed.
nose
collar
body
Do not turn when pressurized.
4
Easy installation reduce working process.
Ordering Instructions 1. If you can select an appropriate coupler on the basis of the usage conditions, specify the catalog number by referring to the BI coupler or swivel joint catalog. 2. If you ask us to select a coupler or if you need a special coupler, specify the following: 1) Fluid to be used 2) Flow rate and velocity. 3) Fluid temperature 4) Maximum working pressure ( Relief valve pressure ) 5) Vibration 6) Installation way ( screw, spanner, etc ) 7) Ambient temperature
3. A cap plug is required for dust prevention and coupler protection. Order the cap plug when using the coupler.The EA, AA, MA, ED, and JCA series are available as standard products. If you need EP, DA, or SD series products, consult us.
poppet 69
BI - Coupler Series
Shape
Structure / Material
For Standard Pressure EA For Hydraulic Oil
Main Body : Steel / Stainless O-ring : NBR / FKM
32 2 ″)
17.0MPa 14.0MPa → 7.5MPa → 3.5MPa → 1.5MPa → →
04
~
32
( 1 4″) ~( 2 ″)
Main Body : Steel / Stainless O-ring : NBR / FKM
27.5MPa
04
~
16
( 1 4″) ~( 1 ″)
Main Body : Steel / Stainless O-ring : NBR / FKM
For Standard Pressure MA For Hydraulic Oil
~ 1 ″ ( 8) ~(
Stainless 04・06 08 12・16 20・24 32
For Standard Pressure AA For Hydraulic Oil
Size
02
Steel 20.5MPa
For Standard Pressure ED For Hydraulic Oil
Max.Working Pressure
34.5MPa
08 ・ 12 ・ 16 ( 1 2″)( 3 4″)( 1″)
Main Body : Steel / Stainless O-ring : NBR / FKM
With Function to Release Residual Pressure EP
20.5MPa
06 ・ 08 ( 3 8″)( 1 2″)
For Hydraulic Oil Main Body : Steel O-ring : NBR
Flat-Face for Die-Casting ENF For Hydraulic Oil
20.5MPa
04
~
04
~
16
( 1 4″) ~( 1″)
Main Body : Steel O-ring : NBR
Dust-Proof / Corrosion Resistance
AA / VKF
27.5MPa
Mineral / Phosphericacid Oil
Ester Oil
70
Main Body : Steel / Electroless Nickel Plating O-ring : NBR / FKM
16
( 1 4″) ~( 1″)
Series
Shape
Stucture / Material
Max.Working. Pressure
Size
~ 08( 1 2″) 04(1 4″)
Brassware DA
7.0MPa
04
~ 16( 1″) 12(3 4″)
~ 16
( 1 4″ ) ~( 1 ″)
3.5MPa
Hydraulic Oil / Water
Main Body:Brass O-ring:NBR
For Jack Application JCA Hydraulic Oil
30JCA06C-XXZ 68.5MPa
04 ・ 06 ・ 08
( 1 4″)( 3 8″)( 1 2″)
(For jack application) Main Body:Steel O-ring:NBR
For Water Jet Application JA
30JA04B-SKFZ 147.0MPa
04
( 1 4″)
30JA04G4M4-SKFZ 245.0MPa
Water
Main Body:Steel O-ring:NBR
For Steam / Water SD Steam / Water
2.0MPa
Main Body:Brass O-ring:NBR / FKM
For Pressure Detection BF Hydraulic Oil
12 ・ 16
( 3 4″)( 1″)
27.5MPa
02 ・ 04
( 1 8″)( 1 4″)
Main Body:Steel O-ring:NBR
Warranty period EA,ED,AA,MA,EP,ENF,DA
1 year or 400,000 impulse cycle whichever comes earlier
JCA, SD
1 year or 200,000 impulse cycle whichever comes earlier
JA
1 year or 25,000 impulse cycle whichever comes earlier
71
Swivel Joints For Safety’s sake
1
Be sure to read the following before use.
The Bridgestone products shown here were developed for mineral hydraulic oil hoses for hydraulic equipment. Products for other uses are also available. Refer to the usage documents and specifications for each series of products. To prevent early damage and fluid leakage, be sure to observe the instructions described below.
1 Handling
Warning
Severe personal injury or death may result if these instructions are not followed.
●Do not touch a pressurized coupling or swivel joint. If a product breaks, you may be burned or fluid may penetrate your skin, destroying your body tissues. If contact between your body and part of the product cannot be avoided during its use, attach sufficiently reinforced plastic hose guards to the part to ensure separation between your body and the part. ●System working pressure should not exceed the rated working pressure. Excessive working pressure may damage internal components or cause fluid leakage. Adhere to the maximum working pressure ratings listed in this catalog. ●Do not apply an electrical current to a hose assembly. Electrifying may lead to an electric shock, damage to internal components, or fluid leakage. Do not apply an electrical current to a hose assembly. ●Use the product with a compatible hydraulic fluid. Using the product with an incompatible hydraulic fluid may damage its internal components or cause fluid leakage. Use the product only with the compatible hydraulic fluid specified in this catalog.
Caution
Personal injury or property damage may result if these instructions are not followed
● Avoid usage exceeding the applicable temperature. Usage exceeding the applicable temperature may damage internal components or cause fluid leakage. Be sure to use the swivel joint at a temperature within the specified range. ● Avoid excessive vibration or external force. Excessive vibration or external force may quickly result in fluid leakage or damage to the product. Do not apply excessive vibration or external force. ● Avoid vacuum pressure Vacuum pressure may damage the internal components or cause their loss. When the product is normally pressurized after being subjected to vacuum pressure, fluid leakage may occur. ●Do not repair or modify the swivel joint. Doing so may deteriorate performance and quickly result in fluid leakage or damage. ●Do not submerge the swivel joint in water or any other liquid. Doing so may corrode the swivel j oint and quickly result in fluid leakage or damage.
2 Installation
Caution ●Properly tighten the parts using the torques specified below. The use of an inappropriate torque makes it difficult to ensure proper sealing and may cause fluid leakage or damage to the joint.
●Install the swivel joint by fixing its shaft and rotating its housing. If you fix the housing, the joint may loosen and detach.
●Do not connect two swivel joints together. If you connect two swivel joints together, an unbalanced load may be applied to them depending on the hose movement, damaging them. Swivel joint made of steel or stainless
Size Designation Tapered pipe thread: R, Rc*1 (reference values)
04
06
08
12
16
20
24
32
25
34
64
140
210
250
310
620
Parallel pipe thread: G
25
34
64
132
196
225
255
412
Unit: N-m *1:The tightening torque for the R thread varies depending on how its sealing tape is wrapped. Therefore, the values shown in the table are for reference only.
3 Warranty Period Warranty is effective until the predetermined usage period expires or the impulse cycle count reaches the predetermined value, whichever occurs first.
4 Preventive Maintenance Before every usage, check for any leakage from the products. If any leakage is discovered, replace the product with a new one immediately.
5 Storage Store at a temperature between −10°C and +40°C avoiding direct sunlight, and in a dry and clean place free from hazardous gases.
72
How to Install a Swivel Joint
1
Caution Do not install the swivel joint with an offset.
Excessive force (unbalanced load) could damage the joint. Whenever practicable, install swivel joints on the same plane (with an offset of 0mm) as the direction of hose movement. If you need to install them with an offset for plumbing, the offset should not exceed the maximum amounts given below. If it exceeds the maximum, reroute the hoses.
Size
Hose Swivel joint
Max. offset
Max. offset
Adapter
Slide
Optimum installation position
2
Caution
Max. offset (mm)
04
±15
06
±15
08
±15
12
±25
16
±25
20
±35
24
±35
32
±35
Do not install a hose so that it is taut. Ensure there is sufficient slack in the hose when you install it.
The length of a hose changes when it is pressurized. If a taut hose is installed, excessive force (unbalanced load) is applied to the swivel joint when the hose is pressurized. Swivel joint RIGHT
WRONG
Hose
Adapter
Hose Swivel joint
Adapter
Slide
3
Caution
Install the swivel joint by fixing its shaft and rotating its housing.
5
Caution
Do not connect two swivel joints together. WRONG
Shaft
Housing
Fix
Fixed side
Swivel joint
4
Caution
(A)
Hose or equipment
Do not install the swivel joint in a way that applies excessive force (unbalanced load) to the joint for rotation, as shown in Figure (B) below. The joint should be installed at a right angle to the fixed side as shown in Figure (A).
(B) WRONG RIGHT
Right angle Rotation
Fixed Rotation side
Fixed side
73
Accessories for Protection
-Catalog No,8XA○○○
Standard Spring Guard
■For the protection of the crimped portion. Sample markings (for factor y-crimped PA0706)
8XA
213
Standard Spring
Inner Diameter of Spring Guard. (213 : spring I.D.=21.3mm) Refer to the chart in pp. 58-59 for the combination of hose and spring I.D.
-Catalog No,8XB○○○
Overall Length Spring Guard
■For the protection for hose entire length from external damage ■If the overall-length spring guard is ordered, the first three characters of the catalog number are changed from 8XA for the standard spring above to 8XB.
Sample markings (for factory-crimped KF04)
8XB
160
Overall Length
Inner Diameter of Spring Guard. (160 : spring I.D.=16.0mm) Refer to the chart in pp. 59 for the combination of hose and spring I.D.
Braided Steel Wire
*The length tolerance for exterior equipment is up to 5% of the product length.
■For the protection for hose entire length from external damage. Example
PA1408-GG Put "-GG" at the end of hose catalog No. For Braid Stainless Steel Wire, put "-SS".
Glass-Wool + Braided Steel Wire
*The length tolerance for exterior equipment is up to 5% of the product length.
Example
EQ1712-GA
GA
1 layer of Glass Wool +1layer of Braided Steel Wire.
GW
2 layer of Glass Wool +1layer of Braided Steel Wire.
GN
3 layer of Glass Wool +1layer of Braided Steel Wire.
SA
1 layer of Glass Wool +1layer of Braided Stainless Steel Wire.
Put "-○○" (shown above) at the end of hose catalog No. Exterior glass wool is effective in protecting the hose against momentary fires and high temperatures. It may not exhibit the expected heat insulating effect if it is used continuously at a high temperature.
Plastic Guard-Catalog No,8XE○○○
*The length tolerance for exterior equipment is up to 5% of the product length.
For the protection for hose entire length from external damage.
76
-Catalog No,8XA○○○
Overall Length Spring Guard-Catalog No,8XB○○○
Standard Spring Guard
*To order the overall-length spring guard, change catalog number 8XA○○○ for the standard spring guards below to 8XB○○○.
Stardard Spring Guard . Hose Series
Hose Size 02
03
PA03 PA10 PA14 PA17 PA21 PA28 PA35 PF07 PF14 PF17 PF21 PFW PFH EQ17 EQ21 EQ25 EQ28 EQ31 OKE VW JW7004 JW7006 JW7008 JWK LP WE21 NW21 WA14 WAR WJ WB21 WH21 R1A R2A KF KG SPL KA
04 ▲8XA168 ■8XA173 ▲8XA168 ■8XA173
PA01 PA07
For information about the method of indicating the catalog numbers, refer to page 76.
For factory-crimped products
Notes
8XA180
1. Check the applicable couplings. They should be the series of devices shown in this catalog. 2. The markings prefixed to certain product names indicate the springs for those series of couplings, as follows. ▲…Spring for AS ■…Spring for UL
-
-
8XA180 8XA180 8XA180 8XA180 8XA180 8XA180 8XA180 8XA180 8XA180 8XA180 8XA180 8XA180
8XA145
8XAJW70
8XA210
8XA180 8XA173 8XA173 8XA173 8XA180 8XA180
8XA146
8XA177
8XA173
8XA188
-
8XA160
8XA120
8XA143
8XA098 8XA138
8XA160
-
05
-
06
08
▲8XA205 ▲8XA250 ■8XA213 ■8XA239 ▲8XA205 ▲8XA250 ■8XA213 ■8XA239
10
12
14
16
20
24
32
-
-
-
-
-
-
-
8XA270 8XA345
8XA221 8XA247 8XA305 8XA333 8XA221 8XA247 8XA305 8XA333 8XA221 8XA247 8XA305 8XA333 8XA221 8XA247 8XA305 8XA333 8XA224 8XA254 8XA305 8XA333 8XA224 8XA254 8XA305 8XA333 8XA224 8XA254 8XA305 8XA333 8XA221 8XA247 8XA221 8XA247 8XA221 8XA254
-
-
8XA224 8XA254 8XA305 8XA333 8XA224 8XA254 8XA224 8XA254
-
-
-
8XA254 8XA305 8XA333 8XA254 8XA305 8XA333 8XA254 8XA305 8XA333 8XA254 8XA305 8XA333 8XA254 8XA305 8XA333
8XA180 8XA222 8XA270 8XA320
8XA239
-
-
8XA254
8XA263 8XA300 8XA218 8XA253 8XA224 8XA254 8XA224 8XA254 8XA213 8XA239 8XA213 8XA239 8XA221 8XA247 8XA221 8XA247 8XA213
-
8XA210 8XA239 8XA233 8XA256 8XA210 8XA258 8XA210 8XA258 8XA190 8XA233
8XA188 8XA203 8XA258
-
-
8XA400 8XA505 8XA560
8XA410 8XA520 8XA545 8XA735 8XA410 8XA520 8XA545 8XA735 8XA410 8XA520 8XA567 8XA735 8XA410
-
-
-
8XA410 8XA520 8XA567 8XA735 8XA410 8XA520 8XA665 8XA820 8XA415 8XA548 8XA665 8XA800
8XA410
-
-
-
8XA410 8XA520 8XA567
-
8XA410 8XA520 8XA567 8XA780 8XA410 8XA520 8XA665 8XA410 8XA548 8XA665
-
8XA415 8XA548 8XA665 8XA800 8XA395 8XA500 8XA570 8XA720 8XA400 8XA505 8XA560 8XA727
-
-
-
-
8XA330
8XA410
8XA355
8XA415 8XA548 8XA665 8XA780
8XA333
-
8XA410
8XA333 8XA380 8XA410
8XA325 8XA343 8XA317
8XA317
-
-
-
-
8XA735
-
8XA408 8XA520 8XA560 8XA710 8XA425
-
-
-
-
*Spring codes for these series of factory-crimped couplings. If you are using a different series of couplings from those specified above, contact us.
77
Accessories for Protection
Hose Series KB AG10 PS PC WSH JC70 SF JAM JAL JAK JKY
Hose Size 02
03
04
05
06
08
10
12
-
8XA138
8XA160
8XA185
8XA210
8XA258
8XA317
-
8XA143
-
8XA190
8XA233
8XA138
8XA160
8XA185
-
8XA160
8XA188
-
-
-
-
8XA145
-
-
-
8XA195
8XA240
8XA253
8XA235
-
8XA256
-
-
-
-
8XA185D25
8XA210
8XA240
8XA302
8XA356
8XA400
8XA190D25
8XA205
8XA240
8XA280
-
-
-
-
-
8XA160
8XA180D25
-
8XA190D25
8XA210
14
8XA310
-
16 8XA408
8XA456
-
20
24
32
-
-
-
*Spring codes for these series of factory-crimped couplings.If you are using a different series of couplings from those specified above, contact us.
Overall Length Spring Guard For UNICRIMP-crimped products Hose Series
For information about the method0 of indicating the catalog numbers, refer to page 70.
Hose Size 06
08
PA01
▲8XB168MA ■8XB170MA
04
▲8XB210MA ■8XB215MA
▲8XB260MA ■8XB239MA
PA03
▲8XB168MA ■8XB170MA
▲8XB210MA ■8XB215MA
▲8XB260MA ■8XB239MA
10
12
16
20
24
32
-
-
-
-
-
8XB284MA
8XB355MA
8XB400MA
8XB505MA
8XB560MA
-
PA07
8XB180MA
8XB215MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB555MA
8XB740MA
PA10
8XB180MA
8XB215MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB555MA
8XB745MA
PA14
8XB180MA
8XB215MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB580MA
8XB745MA
PA17
8XB180MA
8XB215MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
-
-
-
PA21
8XB180MA
8XB215MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB580MA
8XB745MA
PA28
8XB180MA
8XB215MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
PA35
8XB180MA
8XB215MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
PFH
8XB180MA
8XB215MA
8XB260MA
-
-
-
-
-
-
-
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB580MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB580MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
8XB260MA
8XB300MA
8XB340MA
8XB410MA
8XB538MA
-
-
OKE
8XB150MA
8XB180MA
8XB226MA
8XB273MA
8XB310MA
8XB390MA
8XB500MA
8XB570MA
8XB720MA
WA14
8XB170MA
8XB215MA
8XB239MA
WAR
8XB170MA
8XB215MA
8XB239MA
-
-
WJ
8XB180MA
8XB215MA
8XB260MA
8XB340MA
8XB410MA
-
8XB180MA
8XB215MA
8XB260MA
8XB340MA
8XB410MA
-
-
WB21
-
EQ17 EQ21 EQ25 EQ28 EQ31
KF
8XB160MA
8XB210MA
8XB258MA
KG
-
8XB210MA
8XB258MA
SPL
8XB143MA
8XB200MA
8XB244MA
KA
8XB170MA
8XB215MA
8XB239MA
KB
8XB170MA
8XB215MA
8XB239MA
AG10
8XB143MA
8XB200MA
8XB244MA
WSH
8XB160MA
8XB210MA
-
8XB340MA
8XB340MA
-
8XB340MA
8XB430MA
-
-
-
Notes 1. Check the applicable couplings. They should be the series of devices shown in this catalog. 2. The markings prefixed to certain product names indicate the springs for those series of couplings, as follows. ▲…Spring for AS ■…Spring for UL
*Spring codes for these series of factory-crimped couplings.If you are using a different series of couplings from those specified above, contact us.
78
How to calculate Hose Exposed Length Minimum exposed length of hoses that can be manufactured Hose Series(mm)
02
03
04
05
06
08
10
12
16
20
24
32
40
48
Actual hose internal diameter
3.2
4.8
6.3
7.9
9.5
12.7
15.9
19.0
25.4
31.8
38.1
50.8
63.5
76.2
Min. exposed length of hose that
150
150
150
150
160
170
180
190
210
220
350
370
400
400
ー
200
200
200
200
200
200
210
210
ー
ー
ー
ー
ー
can be manufactured
Bridgestone PrimoLine
● For information about the method of indicating assembly hose lengths, refer to “Example Indications of Hose Length and Orientation Angle” on page 5. For dimensions of fittings, refer to the specifications
of the coupling dimensions for each series of hose. ● If you need to use a hose with exterior protection, consult us. ● Minimum exposed lengths may differ from the values above depending on the combination of hoses and couplings.
1
U-shaped hose fixed at both ends
2
3
U-shaped hose fixed at one end, the other end moved by T
Min. exposed length of hose that can be manufactured
r r
●Exposed hose length: (r+D/2) +2D R=π
●Exposed hose length: (r+D/2) +2D+T R=π
●Same as above
R: Exposed hose length r: Minimum bending hose radius T: Distance π: Circular constant D: Hose external diameter
Hose Assembly Installation
1
2
If the bending radius falls below the required minimum, install an elbow adapter as shown above to avoid sharp bends in the hose.
3
Use an adapter to avoid sharp twists or bends in the hose.
5
4
To avoid twists, bend the hose on the same plane as the direction of movement of the base to which the hose is connected.
6
There will be some change in length when the hose is pressurized. Do not clamp the hose at the ben ds in an attempt to avoid the length change. (If the piping design cannot be changed, protect the hose with springs and external wire braid instead of clamping.)
8
7
The hose should have an adequate amount of slack. This slack permits smooth hose movement and prevents sharp bends in the hose.
9
Three-plane bending could result in the hose developing twists when it is under pressure. When the hose moves as shown in the figure on the left, it always twists. Therefore, using the attached tool, clamp the hose so that it moves on only one plane to prevent it from developing twists.
Obtain direct routing of hoses by using an adapter. You can arrange the hoses neatly by avoiding the use of excessively long hoses.
The length of a hose changes by about 4% when it is under pressure. Provide an adequate amount of sla ck to allow for expansion and contraction.
10
By selecting appropriate adapters, you can decrease the number of coupling parts and thereby improve the seal reliability and coupling appearance.
Use the lay line provided on the hose as a reference to examine whether or not the installed hose is twisted. Also, when using a coupling equipped with a union nut, be sure to fix it by tightening the hexagonal portion of the torsion preventive part with a wrench.
79
Hose Assembly Installation Length Tolerances
Tolerance
Horse assembly length (mm)
+10mm 0 +15mm 0 +20mm 0 +1.0% 0 +2.0% 0
Less than 500 500 or more and less than 1,000 1,000 or more and less than 2,000 2,000 or more and less than 5,000
5,000 or more
*Length tolerance for exterior equipment is up to 5% of the product length.
When a liquid flows inside the hose, pressure loss occurs due to friction.
Pressure Loss
You can calculate the approximate pressure loss as follows.
10
Conditions
Pressure Drop Data 02 03
Hose Length:10m
04 05
(Excluding Coupling Lengths)
06
1.0
08
10 12
Fluid:Hydraulic Oil
16
20
Kinetic Viscosity:32.0mm2 /S
24 32 40 48
0.1
Pressure Loss (MPa) 0.01
0.001 1
10
100
1,000
Flow Rate ( / min)
Example Hose I.D.-12 (19mm), Length 5m (with couplings at both ends), Kinetic viscosity 32mm2 /s , Flow rate 80 /min 1 ) By the flow rate 80ℓ/min and hose I.D-12,find the hose pressure loss as 0.2 MPa from the graph above. 2 ) Pressure loss of a coupling is about the same as 1/10 of that of the hose.
0.2MPa ×
5m 1 + 0.2MPa × × 2pcs = 0.14MPa 10m 10
hose pressure loss
coupling pressure loss
3 ) 0.14MPa is estimated pressure loss of this hose assembly. 80
assembly hose pressure loss
10,000
Relational Table of Flow Rate / Velocity / Hose Size Relational Table of FlowRate/Velocity/Internal Hose Diameter
By using this table, you can easily determine the internal diameter of the hose, as follows.
Determining the internal diameter of a hose to supply liquid at a flow rate of 30 litters/minute The flow rate of your system requirement is 150cm3 per second. Connect your straight edge from the 150cm3 per second flow rate column to the Recommendable flow velocity range for pressure lines of 4 meters per second. The straight edge intersects at 04, so the recommended hose size is 04.
The equation below shows the relationship between flow rates, velocities, and internal diameters.
/min, FLOW RATE cm3/sec
Q = 0.0471Vd 2
1
Q : FLOW RATE ( /min) V : VELOCITY (m/min) d : HOSE SIZE:ID.(mm)
20
30 2 40 3
50 60
4 5 6
70
VELOCITY m/sec 0.01
80 90 100
0.02
SECTIONAL AREA OF HOSE(cm2)
Hose internal diameter (in 1/16-inch increments)
7 8
0.04
9
0.06
10 200
30
0.08 20
0.1
32
0. 2 300 0. 3
20
24
30 40 50 60
400
0. 4
500
0. 6
600
0. 8
700 800 900 1000
10 9 8
1
6
3
80 90
4
100
6 8 10
3000 200
400 500 600 700
5000
Recommendable flow velocity range
3
2
12
10
20 08
40 1 60
6000
80
7000
100
8000 9000 10000
16
4
30
4000 300
5
2
70
2000
20
7
0. 8 06 0. 6 05 0. 4 04
800 900 1000 0. 2
03
0.1
81
Tightening Torque
●Follow the below tightening torque. ●The tolerance is approximately ± 10%. ●The application of each of the following torques is allowed on the prerequisite that there is no oil left on the threads portion and inside of the nut and also that the hexagonal part of each insert is firmly held by a spanner so as to prevent the coupling from rotating together with hose.
Coupling (Material : Steel / Surface : Zinc Plating・Chromate Treatment) Hose
Coupling R type *1
( Reference values )
F / C type
02
03
04
05
Pipe thread
ー
ー
Torque N / m
15
ー
Pipe Thread
1/8
1/4
3/8
1/2
Torque N / m
15
25 *15
34 *25
64 *29
UNF thread
ー
ー
Torque N / m
ー
ー
20
M thread
ー
ー
M14×1.5
Torque N / m
ー
ー
25
UNF thread
ー
ー
Torque N / m
ー
ー
ー
40 *15
ー
06
08
40 *25
70 *29
7
1 9 / 16 18 16 20 /2 20 / ー
ー
ー
3
10
12
16
20
24
32
140
210
250
310
620
3/4
1
1 1/4
1 1/2
2
132
196
225
255
412
ー
ー
ー ー
/ 4 16
7
ー
1 / /12 1516 /12 15 8/12 8 14 1 16 ー
ー
ー
ー
F2 / F3 type 29
39
49
59
118
137
ー
167
ー M18×1.5 M22×1.5 M24×1.5 M30×1.5 M33×1.5
ー
ー
ー
ー
ー
ー ー
F4 type
Q2 type
9
/ 16 ー18
78
137
11 / 16 1316 / 16 16
ー
ー
ー
39
49
67
ー
78
176
196
ー
3 7 1 14 1/ /12 11116 /12 2 12 16 12 1 16 ー
118
ー
157
ー
196
ー
ー
ー
327
ー
430
*Products marked with an asterisk are the F- and R-type couplings made of brass. *1:The tightening torque for the R joint varies depending on how its sealing tape is wrapped. Therefore, the values above are for reference only. *For tightening torques for PrimoLine, refer to page 59. *Use a torque wrench for proper tightening.
● For proper tightening , use a torque wrench (shown below)
Bolt for Split Frange(Material : Steel) Hose
Coupling
08
10
12
16
8YA12S
20
24
8YA20S
32
For Standard Pressure
Catalog No.
8YA08S
8YA24S
Torque N / m
20~25
28~40
37~48
48~62
62~79
73~90
For High Pressure
Catalog No.
8YA08S
8YA12H
8YA16H
8YA20H
8YA24H
8YA32H
Torque N / m
20~25
33~45
56~68
85~102
151~181
271~294
Bolt for JIS Frange(Material : Steel) Hose
Coupling For JIS21MPa (210kgf/cm2)
08
10
12
16
20
24
32
Catalog No.
8YAK15
8YAK25
8YAK40
Torque N / m
34~45
54~76
147~230
40
48
8YAK65
8YAK80
314~451 470~637
When a split flange or a square flange is used for a hose connection, the bolts must be tightened diagonally with the same torque applied. Otherwise, the flange will incur damage, possibly followed by oil leakage.
82
Certificate of Compliance with the Marine Standard Our products have obtained a certificate of compliance with the marine standard, as shown below. Since then, they have earned a worldwide reputation.
Products Certified for Compliance with the Marine Standard Standard
Hose
NK
JG
LR
BV
DNV
KR
CR
ABS
CCS
(Japan)
(Japan)
(U.K.)
(France)
(Norway)
(Korea)
(Taiwan)
(U.S.A)
(China)
Nippon Kaiji Kyokai
MLIT Maritime Bureau
Lloyd's Register of Shipping
Bureau Veritas
Det Norske Veritas
Korean Bureau of Shipping
Central Research of Shipping S.A.
American Bureau of Shipping
China Classification Society
PA07 04~32
◎
◎
◎
◎
◎
20~32
◎
◎
PA10 04~32
◎
◎
◎
◎
◎
20~32
◎
◎
PA14 04~32
◎
◎
◎
◎
◎
20~32
◎
◎
PA17 04~16
◎
◎
◎
◎
◎
-
◎
◎
PA21 04~32
◎
◎
◎
◎
◎
20~32
◎
◎
PA28 04~32
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
R1A 03~32
◎
◎
R2A 03~16
◎
◎
EQ17 08~24
◎
EQ21 08~32
◎
EQ25 08~24
◎
EQ28 08~24
◎
EQ31 08~32
◎
F o r c e r t i f i e d s i z e s , c o n t a c t u s .
1. Witness inspection is required each time a product is tested for certification by an organization other than CR, ABS, or DNV. Contact us. 2. When a product to be used inside an engine room is tested for certification by Bureau Veritas (BV), an external wire braid is required for that product.
83