Huawei GENEX Probe & Assistant practice guide
Internal use only
Table of Content 1
Probe practice............................................................................................................3 1.1 Target................................................................................................................3 1.2 1.3
1.4 2
Task Requirement.............................................................................................3 Drive Test..........................................................................................................4 1.3.1
Install the GENEX Probe software on PC.....................................................................4
1.3.2
Prepare the Engineering Parameter File......................................................................4
1.3.3
Connect the UE to PC and install the driver for the test mobile....................................4
1.3.4
Connect other hardware as figures followed:................................................................9
1.3.5
Create a new project.....................................................................................................9
1.3.6
Configure the hardware..............................................................................................10
1.3.7
System Config - Test Plan...........................................................................................12
1.3.8
Import NodeB Engineering Parameters......................................................................14
1.3.9
Import the Map for outdoor test...................................................................................14
1.3.10
Save the project......................................................................................................14
1.3.11
Start the test...........................................................................................................14
1.3.12
Stop the test............................................................................................................15
1.3.13
Replay log file.........................................................................................................15
Indoor Test ( Manual Walking Test )................................................................15
Assistant practice....................................................................................................16 2.1 Target..............................................................................................................16 2.2
Practice to analyse the Drive Test log file.......................................................16 2.2.1
Install the GENEX Assistant software on PC..............................................................16
2.2.2
Prepare the Engineering Parameter File....................................................................16
2.2.3
Create a project..........................................................................................................16
2.2.4
Create a dataset.........................................................................................................16
2.2.5
Map Configuration.......................................................................................................17
2.2.6
Importing test data to a dataset..................................................................................17
2.2.7
Importing Engineering Parameters.............................................................................18
2.2.8
Practice to view the test data from various methods..................................................18
2.2.9
Analysis specified data...............................................................................................18
2016-12-29
Huawei Confidential
Page1, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
List of Figure Figure 1-1 Step 1 of UE driver installation...................................................................4 Figure 1-2 Step 2 of UE driver installation...................................................................5 Figure 1-3 Step 3-Specify the path we stored the driver files......................................5 Figure 1-4 Warning message of the compatibility........................................................6 Figure 1-5 Step 4-Finish installing software for 3G modem........................................6 Figure 1-6 Finish installing software for 3G Application Interface................................7 Figure 1-7 Enter Computer Management....................................................................7 Figure 1-8 Device manager.........................................................................................8 Figure 1-9 Serial Port of the 3G Modem......................................................................8 Figure 1-10 Hardware connection of GENEX Probe test system................................9 Figure 1-11 Create a new project by the OutDoorTest template project....................10 Figure 1-12 Hardware configuration interface...........................................................10 Figure 1-13 UE( Huawei U626) configuration............................................................11 Figure 1-14 Scanner (DTI scanner) configuration......................................................11 Figure 1-15 System Config - Select UE and configure..............................................13 Figure 1-16 Select Device - Scanner.........................................................................13 Figure 1-17 Test plan parameters for DTI scanner....................................................14 Figure 2-1 Interface of Assistant when new project is created..................................17 Figure 2-2 Interface of Assistant when test data is imported.....................................18
2016-12-29
Huawei Confidential
Page2, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Huawei GENEX Drive Test tools Practice Guide Abbreviation: User Manual:
In Probe practice section, it means GENEX Probe Wireless Air Interface Testing Software User Manual.pdf, V100R003, 3058KB, 2006-08-31
In Assistant practice section, it means GENEX Assistant Wireless Post-processing Software User Manual.pdf, V100R002, 5335KB, 2006-08-30
Definition for the words style:
section 8.3.9: section or chapter in User Manual
“USB DIAG”: menu item of the software
Double click the 3G Modem icon: important notice
1 Probe practice 1.1
Target By carrying out a Video Call test, master:
1.2
1.
the hardware of Probe system and the connections
2.
how to setup a test project
3.
how to collect the Drive Test data
4.
how to view information during test
5.
how to replay the Log File to analyze data
Task Requirement Carry out a Video Call test, connect all the hardware property, and configure the software follow by the demand: 1.
Make a shot-call VP test (call by call). Each call lasts 105 seconds after connection then hung up automatically, then makes another call 15 seconds later after the end of previous call.
2.
The test maybe last 2 hours, or maybe last 4 hours.
3.
Import the map and BTS parameter.
4.
Setup the UE and scanner parameters and related parameters of the test plan property.
5.
Can start the test without any trouble and log the file correctly.
2016-12-29
Huawei Confidential
Page3, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
1.3
Internal use only
Drive Test
1.3.1
Install the GENEX Probe software on PC Install the Probe software on PC according to chapter 4.4 of User Manual. Chapter 5 introduces the Graphical User Interface of Probe.
1.3.2
Prepare the Engineering Parameter File Engineering Parameter File is optional, but it is recommended so the engineer know which is the nearest NodeB, further more Probe will draw a line between the current locate and the NodeB the UE camps on.
1.3.3
Connect the UE to PC and install the driver for the test mobile 1、 Power on the UE 2、 Set the diagnosis port of the UE to USB port: Press the three keys at the same time (*, #, and “Left” key) to enter the engineering mode, then press “Others” - “DIAG port set” - “USB DIAG”. 3、 Make sure the driver files are already on local disk. For example in folder F:\U626_Driver\WinXP. 4、 Connect the UE to the USB cable; plug the other end of the cable to a USB port of the PC, then followed by steps below: A dialog like Figure 1 -1 will appear in a few seconds:
Figure 1-1 Step 1 of UE driver installation
Choose the button as Figure 1 -1 shows. Then click “Next”. A dialog will appear as Figure 1 -2:
2016-12-29
Huawei Confidential
Page4, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 1-2 Step 2 of UE driver installation
Choose the button as Figure 1 -2 shows. Then click “Next”. A dialog will appear as Figure 1 -3:
Figure 1-3 Step 3-Specify the path we stored the driver files
Click the “Browse” button to specify the path stores the driver files. (Here the path is F:\U626_Driver\WinXP). Then click “Next”. A warning message will pop up as shown Figure 1 -4, choose “Continue Anyway”.
2016-12-29
Huawei Confidential
Page5, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 1-4 Warning message of the compatibility
The driver files then will be copied to the system. After a while, a message will appear to say the drive of a 3G modem is successfully installed.
Figure 1-5 Step 4-Finish installing software for 3G modem
A few seconds after we click “Finish” on Figure 1 -5, another dialog same as Figure 1 -1 will appear. It means installation software for the 3G application interface. And followed by 3 dialogs same as shown by Figure 1 -2~ Figure 1 -4. Figure 1 -6 says installation of 3G application interface is successful.
2016-12-29
Huawei Confidential
Page6, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 1-6 Finish installing software for 3G Application Interface
5、 Check if the software is installed proper Go to the system device manager by right click “My Computer” on Desktop, and then choose “Manage” as Figure 1 -7 below:
Figure 1-7 Enter Computer Management
Then click “Device Manager” to switch to device management interface as shown below:
2016-12-29
Huawei Confidential
Page7, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 1-8 Device manager
If we can see the HUAWEI Mobile Connect - 3G Modem, 3G Application Interface and a USB Composite Device, all the installations are correct. Notice: From Figure 1 -8 the serial port number of the engineer mobile is COM5. Double click the 3G Modem icon; we can get the serial port number of the Modem on the pop-up window from its “Modem” tab; maybe it is COM4 as shown in Figure 1 -9 below. Remember these two COM port numbers.
Figure 1-9 Serial Port of the 3G Modem 2016-12-29
Huawei Confidential
Page8, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
1.3.4
Internal use only
Connect other hardware as figures followed: Notice: Please do not forget to plug the dongle to the PC.
Data Indicator GPS Antenna
RF Antenna
Figure 1-10 Hardware connection of GENEX Probe test system
1.3.5
Create a new project Start the Probe software. Make sure the dongle is plugged right in the USB or parallel port before the software start. Otherwise test could not be started. Select menu “File” - “Template Project” - “OutDoorTest.xml” to open a template project provided by Probe:
2016-12-29
Huawei Confidential
Page9, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 1-11 Create a new project by the OutDoorTest template project
1.3.6
Configure the hardware 1、 Select Menu “Configuration” - “Hardware Config” - “Manual Config…” to the configuration dialog:
Delete a selected device Port test
Add a device
Double click to modify config See Figure 113 & Figure 114
Port status indicator, each lamp correlates with a port
Figure 1-12 Hardware configuration interface
2、 Configure the UE:
2016-12-29
Huawei Confidential
Page10, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Note 1 Note 2
Figure 1-13 UE( Huawei U626) configuration
Note1: For the Com port, fill the 3G Application port got from Figure 1 -8. Note2: For PS service test only, here fill the serial port of the Modem got from Figure 1 -9. 3、 Setup the DTI scanner like Figure 1 -14:
Figure 1-14 Scanner (DTI scanner) configuration
Normally DTI scanner is connected to the onboard serial port (com1) of the PC. If it is connect to some other serial port such as USB-to-Serial port, please get the right port from the Device Manager (see Figure 1 -8). DTI scanner has a GPS internal, so it’s no need to configure GPS. 4、 After configure the Huawei U626 UE and DTI scanner, click the port test button as indicated in Figure 1 -12 to check the devices.
2016-12-29
Huawei Confidential
Page11, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Note: Only the device checked successfully could be identified by Probe system. If any item checked failed, please check the hardware connection, the equipment parameters such as port and baudrate, etc. 1.3.7
System Config - Test Plan Including Test Plan, LogMask, Event, Alarm and Other related settings. Here we focus on Test Plan. Other settings keep default. For more details, refer to chapter 6.7 setting the system. 1、 Click menu “Configuration” - “System Config…” to the system config interface. Figure 1 -15 shows how to configure a video call. 2、 Note for Figure 1 -15: Action 1: choose device, first choose UE1 Action 2: click the TestItem bar to choose a service we would test. Choose Video Phone. Action 3: Set the parameters for Video Phone service test: Enable: True to enable the test item Destination Number: the number being called Setup Time (sec): keep the default - 25. Calling Duration (sec): fill it 105. Call Interval (sec): fill it 15 (Default value is 15, too). Exceptional Interval (sec): keep the default - 20. Call Count: total number of calls. In this exercise the test will last about 2 hours to 4 hours. From the given parameters we can calculate one call will last about 135 seconds (5sec+105sec+15sec). So the count will be about 4*3600/135≈107 times. It is suggested to set a count big enough to ensure the video call will go on testing until the test is stopped by the engineer. Here we set 300. Note: More details about the parameters above, see section 8.2.1 and 8.2.2.
2016-12-29
Huawei Confidential
Page12, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 1-15 System Config - Select UE and configure
3、 Like action 1 in step 2, choose Scanner1 to configure parameters for scanner. Figure 1 -16 and Figure 1 -17 is the config interface. DTI scanner can provide 6 test functions. We only need TopN Pilot Scan. So just enable it, others functions keep them disable. Figure 1 -17 says for TopN Pilot Scan we only need to set the channel. It equals the downlink frequency (MHz)*5. For more details about other parameters, see chapter 8.3.
Only enable TopN Pilot Scan
Figure 1-16 Select Device - Scanner 2016-12-29
Huawei Confidential
Page13, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 1-17 Test plan parameters for DTI scanner
1.3.8
Import NodeB Engineering Parameters According to section 6.5.1 and 6.5.2, import the engineering parameters prepared in step 1.3.2 of this document. Then display the BTS information on the map followed by section 6.5.4.
1.3.9
Import the Map for outdoor test According to section 6.6.1.I, import the map of the tested area. Also we can import a raster map according to section 6.6.1.II.
1.3.10 Save the project To save current project, chose menu “File” - “Save”. All the system and individual settings are automatically saved into one project file. We can open it next time. 1.3.11 Start the test There are three ways to start a test:
From the menu: Choose “Test” - “Start Test”.
From the Navigator: Click the start test icon on the navigator.
From the toolbar: Click the start test icon on the toolbar.
Note: Before the test, Probe gives a prompt indicating whether to save the log file or not. If we choose “Save”, Probe will save the log file as the specified filename. If we choose “Cancel”, Probe will also start the test, but do not save the log file. Other operators during the test, refer to chapter 9.2 (section 9.2.3~9.2.7) of the User Manual. 2016-12-29
Huawei Confidential
Page14, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
1.3.12 Stop the test According to three ways to start a test, there are also three ways to stop a test:
From the menu: Choose “Test” - “Stop Test”.
From the Navigator: Click the stop test icon on the navigator.
From the toolbar: Click the stop test icon on the toolbar.
1.3.13 Replay log file Referring to chapter 9.6 of the User Manual, open a Log File and practice to replay it.
1.4
Indoor Test ( Manual Walking Test ) Referring to chapter 9.4 of the User Manual, carry out an indoor test in manual mode according to section 9.4.1.II
2016-12-29
Huawei Confidential
Page15, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
2 Assistant practice 2.1
Target By analyzing a certain data logged by Probe, master:
2.2
1.
Project manage
2.
Varies display modes of data analyse
3.
Generate statistics report and analyse it
4.
How to analyse coverage, pilot pollution, and neighbor missing
Practice to analyse the Drive Test log file
2.2.1
Install the GENEX Assistant software on PC Install the Assistant software on PC according to chapter 3.3 of Assistant User Manual. Chapter 4 introduces the interface of the software. Note: From now on, USER Manual means GENEX Assistant Wireless Postprocessing Software User Manual.pdf, V100R002, 5335KB, 2006-08-30.
2.2.2
Prepare the Engineering Parameter File Engineering parameter may assistant engineer to analyse data more efficiency. Note: Up to now, the required format of engineer parameter in Assistant is not same as in Probe. Please pay attention to the different format of the frequency and PSC in the parameter file.
2.2.3
Create a project Referring to section 5.2.1, create a new project. Then Assistant will prompt a “New Dataset” dialog to create a dataset. Or we can open a previous saved project according to section 5.2.2.
2.2.4
Create a dataset When a new project is created, Assistant will prompt a “New Dataset” dialog to create a dataset. Or we can create a new dataset to a project according to section 5.3.1. The parameters in “Scanner Setting” tab, normally it is recommended to set as the RNC parameters. For this practice, we keep them default. Parameters in “Binning Type” tab are kept default, too. Now the interface may look like Figure 2 -18.
2016-12-29
Huawei Confidential
Page16, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 2-18 Interface of Assistant when new project is created
2.2.5
Map Configuration Specify the map path according to chapter 5.4.
2.2.6
Importing test data to a dataset Import the specified Probe log file to the dataset according to section 6.2.2. Note: Assistant can analyze various types of data. For more details see other sections in chapter 6.2. Now the interface may look like Figure 2 -19.
2016-12-29
Huawei Confidential
Page17, Total 18 Pages
Huawei GENEX Probe & Assistant practice guide
Internal use only
Figure 2-19 Interface of Assistant when test data is imported
2.2.7
Importing Engineering Parameters Import the engineering parameter file prepared in section 2.2.2 according to section 6.3.1.
2.2.8
Practice to view the test data from various methods Referring to chapter 7, view and analyse the test data in different modes, master to display different data in different mode. Please note that all the Charts/Sheets/Map windows are co-activation. Some skills: 1. 2. 3. 4. 5. 6. 7. 8. 9.
Display data in current view window or a new window by context menu Display data in current view window by dragging it to the window Display data on map (chapter 7.2) Display data on chart, try related operation in chart view (section 7.3) Display data in a crossed Double-Indicator chart (section 7.3.2) Display data in a histogram chart (section 7.3.3) Display data in a caky chart (section 7.3.4) Display data on sheet (chapter 7.4) Display messages by message browser mode and searching specified message (chapter 7.5) 10. Lock the data (chapter 7.5) 2.2.9
Analysis specified data Analysis a test data, it contains some failure such as call drop, neighbor missing, pilot pollution, etc. Please find out what failure is in the data, and try to find what cause the failure. Furthermore, give out your suggest to avoid it.
2016-12-29
Huawei Confidential
Page18, Total 18 Pages