Herramientas de Diagnostico Caterpillar

Diagnostic Tool Quick Reference Caterpillar Service Technology Group

171-4400 Function:

30-Jan-02

Communication Adapter II Gp.

Allows PC to communicate with engine data link

- Required PC software is included - CE Compliant - 4 times faster flash times with J1939 - Flash memory, no SPM - 4 DataLinks: ATA(J1708) RP1210 Compatible, Cat Data Link, J1939, DeviceNet (CAN) - Replaced 7X1700 Communications Adapter I - For more information, see NEHS0758 Getting Started Guide

177-8910 Function:

Power Link Group

Measures actual drawbar horsepower of Ag Tractors

- Designed to accommodate a wide range of tractors & implements - Measures tractors with up to 18,160kg (40,000lbs) drawbar pull and 36,320kg (80,000lbs) max rating - Measures true ground seep and draft load - For more information, see PELJ0045 IRM & NEHS0768 Tool Operating Manual

187-8520 Function:

Wireless ET Link Group

Wireless ET Communications

- Allows full ET functionality without being connected to the machine - 1.5 Mile range (Line of site) - Works with CA I & CA II - 2.4 GHz transmit and receive frequency - No license required - For more information, see PELJ0057 IRM

189-1720 Function:

Analog Gauge Tester Gp.

Used to test analog temperature, pressure, fuel and articulated gauges

- Used to test and troubleshoot analog temperature, pressure, fuel, & articulatoin gauges - Analog guage specifications provided - Decrease troubleshooting time and reduce cost by eliminating replacement of good parts - Fuse protected from electrtical overload - For more information, see PELJ0062 IRM & NEHS0786 Tool Operating Manual

191-3520 Function:

Pro Link Plus

Display and Datalogger for On-highway truck systems

- Displays and prints fault codes and log codes - Snapshot datalogger - Displays engine rating information - CE Compliant - Requires 191-3521 Caterpillar Cartridge - For more information, see PELJ0055 IRM

Caterpillar: Confidential Green Last Modified: 01/30/2002

Page 1 of 24

Diagnostic Tool - Quick Reference

1U-6602 Function: -

Measures engine RPM

Measures RPM by directing light beam onto piece of reflective tape RPM can be measured to and is accurate within 1 RPM LCD viewed simultaneously while aiming the instrument Provides low cost tachometer for general use For more information, see SEHS8854 Special Instructions

1U-8860 Function: -

Pickup Gp. - Blowby

Checks blowby volume on large engines

Optional pickup for use with 8T-2700 Blowby/Airflow Group Large 38 mm (1.5 in) pickup used on large engines without increasing crankcase pressure All metal construction and alrge size makes tool suitable for permanent installation Can also measure air velocity such as radiator cooling air flow For more information, see SEHS8984 Service Manual

6V-2150 Function: -

Photo-Tach Gp.

Analyzer Gp. - Starting/Charging

Checks 14 test points in 24-volt starting and charging systems

For machines that have automotive type key start and a diagnostic connector Allows one man to quickly check 14 test points in starting and charging system Identifies deteriorated starting and charging system components before they fail Requires 110-4645 Adapter Cable As.

7X-1400 Function:

Digital Diagnostic Tool Gp.

Used for monitoring engine functions and diagnostic fault codes

- Displays diagnostic faults, Engine RPM, Engine Detonation Level, & Allows for calibration - Part of 146-2727 G3600 Operator Tool Gp. - Requires NEXG4511 Service Program Module

8T-1000 Function:

Electronic Position Indicator Gp.

Measures dynamic and static rack position & other linear measurements

- 3 separate storage memories record minimum, maximum, and difference values - Digital readout (0-1) range 0 - 25.4mm - 8T-1001 Indicator powered with internal 9-volt battery; AC power adapter available - For more information see SEHS8623 Special Instructions & NEHP5597 Brochure

8T-2700 Function:

Blowby/Air Flow Indicator Gp.

Measures engine blowby gas & air velocity through radiator

- Volume of blowby gases very helpful in planning engine repairs - Air velocity helpful to quickly find plugged or partially restricted areas - Battery-powered digital indicator - Part of 146-2726 Maintenance Tool Gp. - For more information see SEHS8712 Special Instructions


Page 2 of 24


8T-5200 Function: -

Measures frequency signals and generates square wave signal

Small handheld square-wave generator Used to simulate speed in place of magnetic speed pickup Frequency counter when unput is pulsating For more information, see SEHS8579

9U-6958 Function: -

Signal Generator/Counter Gp.

Module - Magneto Peak Detect

Checks magneto performance during actual operating conditions

Used to check magneto performance during actual operating conditions When used with 146-4080 Digital Multimeter, user can measure magneto output DC Voltage Provides separate voltage output for oscilloscope viewing of firing pulse train Does not require power to operate

9U-7400 Function:

Multitach II Gp.

Measures engine RPM, frequency, and engine set point

- Easy to use photo pickup for fast RPM measurement - Two digital displays show Input 1 and Input 2 values simultaneously - Backlit display for low light conditions - Rechargable batteries - Accepts many different types of pickups (Including some Multitach I pickups) - For more information see NEHS0605 Tool Operating Manual & NEHP5596 Brochure

9U-7401 Function:

Multitach II

Used to measures engine RPM, frequency, and engine set point


9U-7402 Function:

Multitach II Photo Gp.

Used to measures engine RPM, frequency, and engine set point


9U-7500 Function: -

Transmission Analyzer

Shift Electronic Transmissions during testing on Test Bench

Easy to read menus, on backlit LCD dislay step you through sequence of operation Performs: Solenoid Condition Check, Transmission Shifts of all gears, & Shift Lever test Flash memory allows internal software to be upgraded. Subscription NETG5021 For more information, see NEHP5617 Brochure & NEHS0644 Tool Operating Manual CE Compliant


Page 3 of 24


156-1060 Function: -

Used to setup, service, and monitor natural gas engine emissions

Used for fast and easy set-up and servicing of lean burn and stoichometric engines Measures exhaust concentrations of O2, CO2, NO, and NO2 Built in thermal printer and Automatic water dump For use on Gas Engines Only - CE Compliant For more information, see PELJ0020 IRM & NEHS0713 Tool Manual


Analyzer Gp. - Emission

Analyzer Gp. - Emission

Used to set-up, service, & monitor natural gas & diesel engine emissions

Used for fast and easy set-up and servicing of lean burn and stoichometric engines Measures exhaust concentrations of O2, CO2, NO, NO2, and CxHx Measures exhaust and ambient temperatures, stack draft, and smoke test Built in thermal printer and Automatic water dump - CE Compliant For more information, see PELJ0020 IRM & NEHS0713 Tool Manual

170-8500 Function:

Particle Analyzer

Used to analyze particle contamination on pressurized and non-pressurized systems

- Provides instant feedback on effectiveness of filtration, abnormal wear conditions, and overall system cleanliness - Allows real-time testing of repaired units - Touchscreen Interaction - Internal Battery - CE Compliant

188-0645 Function:

Portable S2 Particle Analyzer

Used to analyze particle contamination on pressurized and non-pressurized systems

- Provides instant feedback on effectiveness of filtration, abnormal wear conditions, and overall system cleanliness - Allows real-time testing of repaired units - For more information, see NEHS0777 Instruction Manual & PELJ0050 IRM - CE Compliant

146-4080 Function:

Multimeter Gp. - Digital (RS-232)

Measures voltage, current, resistance, duty cycle, temp, & more

- True RMS Digital Multimeter - Full Function Digital Measurements - Can be used with DataView to log any type of electrical signal (Requires 146-8488 Cable) - Provides 10th channel input for DataView - CE Compliant - For more information, see JEDG6000 Brochure & NEHS0554

6V-7070 Function:

Digital Multimeter

General purpose multimeter for measuring current, voltage, & resistance

- Easy to use - Very Durable - CE Compliant


Page 4 of 24


9U-7330 Function:

Multimeter - Fluke 87

Used to test and adjust electronic circuits

- True RMS Digital Multimeter - Measures: ACV, DCV, Amp, Hz, Duty Cycle, Diode, Temp, & Impedence - CE Compliant


Insulation Tester Gp.

Measures & checks insulation resistance for electrical power generation

Used to measure and check insulation resistance for electrical power generation Analog scale reads up to 10 GW for high insulation resistance readings Meter ranges from 100 kW digital & 10 MW analog to test for faults on motors & generators Tool defaults to voltmeter operation whenever an external voltage greater thant 25 VAC/DC Replaces 9U-6003 Insulation Tester

152-7213

Scopemeter (123-120 VAC)

C66974T1 A CO

M B

Function:

Used to test and adjust electronic circuits

- Dual channel digital scope and dual channel true-RMS DMM - Brilliant high contrast backlit LCD with hardened scratch-resistant lens - AUTO key for fast, rock stable waveform displays of signals down to 1 Hz - Frequency range: 20 Hz at input - CE Compliant - For more information, see NEDG6011 Brochure

163-0096 Function:

Process Calibrator

Used to source and calibrate temperature and electrical signals

- Calibrates thermocouples, RTD's, voltage, resistance, Hz, Ma - CE Compliant - Stores up to 8,000 readings - Multilingual operation - Products requiring us of calibrator: 3600 Engine Protection Systems, Marine Monitoring Systems, 3600 Engine Management Systems, 3600 Custom Program Logic Control - For more information, see PELJ0023

4C-5521 Function:

Phase Sequence Meter

Identifies phase sequence of energized 3-phase power lines

- Provides positive identificaion of phase sequence of energized 3 phase 40-60 Hz power lines from 100 to 600 Volts - Gives user inidication that all phases have continuity or will indicate phase that has fault - Has heavily insulated fused leads for users protection - Enhanced durability because there are no moving parts

9U-5222 Function: -

Voltage Detector - AC

Used to locate energized circuits

Safe, quick, and easy way to locate energized circuits Good tool choice when looking for open fuses or circuit breakers or even broken wires Both audio and visual indicators For more information, see NEHS0564 Tool Operating Manual


Page 5 of 24

F1 A V

Hz

F2 F3

A

F4 mV

B V

V HO RULD N

s TI

ME

ns

SC O MENPE U US

OP ER TIO NS

SA PR VE IN T

Hz

mV

V

AU

TO

A


155-5175 Function:

AC Current Probe

Used to measure AC current

- Measure up to 1000 Amps AC with standard Digital Multimeter - Used with 6V-7070, 9U-7330, or 146-4080 Digital Multimeter - Replaces 6V-4960 AC Current Probe - CE Compliant

155-5176 Function:

AC/DC Current Probe

Used to measure AC & DC current

- Measure up to 1000 Amps AC/DC with standard Digital Multimeter - Used with 6v-7070, 9U-7330, or 146-4080 Digital Multimeter - Replaces 9U-5795 AC/DC Current Clamp - CE Compliant

6V-9130 Function:

Temp Adapter Gp.

Used to measure oil, coolant or air temperatures (-50°C to 900°C)

- Used with 9U-7330 or 6V-7070 Digital Multimeter Groups - Kit converts Included Type K Thermocouple to mV readable by standard Multimeters - CE Compliant - For more information, see SEHS8382

8T-0900 Function:

Ammeter - AC/DC Clamp-On

Measures AC & DC current in cables without breaking circuit (0-1200A)

- Measure AC/DC Current up to 1200 Amps - Digital Readout on handle - Used with 6V-7070, 9U-7330, & 146-4080 Digital Multimeters

1U-8115 Function:

Test Lead Set - Insulated Tip

Test lead probes with spring loaded insulators

- Used with 9U-7330, 6V-7070, & 146-4080 Digital Multimeter Gp.

6V-7072 Function:

Test Lead Set

Test Lead Kit for use with Digital Multimeters

- Deluxe Test Lead Kit for all Meters - Includes Alligator Clips, Test Leads, & Banana Leads - For use with 6V-7070, 9U-7330, & 146-4080 Digital Multimeters - CE Compliant


Page 6 of 24


7X-1710 Function:

Probe Gp.

Used to measure voltages without disconnecting wiring harness

- Allows user to measure electrical signal from connector without separating connector - Used with 6V-7070, 9U-7330, & 146-4080 Digital Multimeter Gp.

164-3310 Function:

Infrared Thermometer

Measures surface temperature without contact (battery powered)

- Full Featured Infrared Thermometer -32 - 900 C (-25 - 1600 F) - Bar Graph Display - Laser Circle Shows Size of Area being Measured - CE Compliant - For more information, see NEHP6016 Datasheet

164-3320 Function:


Measures surface temperature without contact (110 VAC or battery)

- Full Featured Infrared Thermometer r -32 - 900 C (-25 - 1600 F) - Log Up to 100 Readings - PC Data Graphing Software - 110V Charger - CE Compliant - For more information, see NEHP6016 Datasheet

166-9030 Function:


Measures surface temperature without contact (220 VAC or battery)

- Full Featured Infrared Thermometer -32 - 900 C (-25 - 1600 F) - Log Up to 100 Readings - PC Data Graphing Software - 220V Charger - CE Compliant - For more information, see NEHP6016 Datasheet

192-3750 Function:


Measures surface temperature without contacting surface

- Small compact size -32 - 400 C (-25 - 750 F) - Accuracy of +/- 1% of Reading - For more information, see NEHP6016 Datasheet - CE Compliant - Replaces 148-2388 Infrared Thermometer

192-3755 Function:


Measures surface temperatures without contacting surface

- Small compact size -32 - 600 C (-25 - 1100 F) - Calculates max, min, & average temperatures - For more information, see NEHP6016 Datasheet - CE compliant - Replaces 148-2400 Infrared Temperature Tool


Page 7 of 24




Non-Contact Temperature Measurement

Low Cost Infrared Thermometer -20 to 260 C (0 to 500 F) Temperature Measurement Range Circle Laser CE Compliant

4C-6090 Function:

Multichannel Temp Selector

Measures up to sixteen temperatures individually

- Measures 16 temperatures individually - Allows serviceman to read individual cylinder exhaust temperatures to locate faulty injector - Used with 6V-7070 & 9U-7330 Multimeters with 6V-9129 Temperature Adapter - OR Used with 146-4080 Multimter with type K Measurement capability - For more information, see NEHS0537 Special Instruction

4C-6500 Function:

Digital Thermometer Gp.

Used to measure and record temperatures

- Fast and accurate method of measuring temperature - Backlit, digital LCD Display for use in low light conditions - Large Display for easier viewing - Provides user with differential temperature measurement between 2 and 5 channels - For more information, see NEHS0554

8T-2844 Function:

Recorder Gp.

Measures highest surface temperature of engine components

- Used for checking operating temperatures of the cooling, engine oil, hydraulic, & brake systems - Quick, easy, inexpensive method to determine component's surface temperature - 6 silver colored temperature sensitive indicator windows on each recorder - 5 different temperature recorders for 5 different ranges

146-1738 Function:

Borescope - Precision (12")

Used to make visual inspection of internal surfaces

- 305mm (1ft) shaft, 6.53mm (.25 inches) diameter - Includes 90 degree mirror tube for right angle viewing - Adjustable focus - Portable battery light source - For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM

8T-9290 Function:

Borescope - Battery Operated


- Fits into bores as small as 8mm (.32") and reach 240mm (9.5 inches) - Battery handle can be remotely coupled to scope using extension cable (supplied) - For more information see NEHS0504 Tool Operating Manual & PELJ0046 IRM


Page 8 of 24


1U-5268 Function: -

Borescope


580 mm (23 in) Length, 6.5 mm (.25 in) Diameter Allow straight viewing of internal surfaces Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery) For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM

9U-6940 Function:

Borescope - Right-angle View

Used to inspect internal openings and passages

- 6.50mm (.256 inches) probe diameter, 570mm (22.5 inches) working length - Housing eliminates surface mirror scratching problem - 60 Degree Field Of View - Fits through nozzle hole on engines using a "pencil style" injector - Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery) - For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM

186-0170 Function:

Flexible Shaft Borescope


- 6mm (.256 inches) probe diameter, 600mm (24 inches) working length - The flexible portion of the borescope is waterproof and resistant to 60 deg. C (140 deg. F) - For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM - Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery)

186-0180 Function:

Borescope - Rigid Tube


- 14mm (.551 inches) probe diameter, 940mm (37 inches) working length - 140 degree adjustable direction of view with 45 degree field of view - Sealed tip to prevent contamination from oil or fuel - Used with Light Source 1U-56266(110 VAC) 190-8160 (220V) & 1U-5265 (Battery) - For more information see NEHS0504 Tool Opeating Manual & PELJ0046 IRM

1U-5266 Function:

Light Source (110 VAC)

Provide illumination for borescopes

- Compact, lightweight - Uses 150 watt light bulb, light intensity is adjustabl - Inlcudes a fan to prevent overheating - Bulb is protected with a 2 amp fuse - Alternative Tool: 190-8160 Light Source (220 VAC) - Used with 1U-5268, 9U-6940, 186-0170, and 186-0180 Borescopes

190-8160 Function:

Light Source

Provide illumination for borescopes

- Uses 150 watt light bulb, light intensity is adjustable - Compact, lightweight - Inlcudes a fan to prevent overheating - Bulb is protected with a 2 amp fuse - Alternative Tool: 1U-5266 Light Source (110 VAC) - Used with 1U-5268, 9U-6940, 186-0170, and 186-0180 Borescopes - For more information see, NEHS0504 Operation Manual & PELJ0046 IRM


Page 9 of 24


1U-5265 Function:

Battery Operated Light Source

Portable Light Source for Field Use

- Used with 1U-5268, 9U-6940, 186-0170, & 186-0180 Caterpillar Borescopes - 110 V Rechargabel Light Source for Caterpillar Borescopes - For more information, see NEHS0504 & PELJ0046 IRM

1U-5470 Function:

Engine Pressure Gp.

Checks pressures on turbocharged diesel and natural gas engines

- Checks pressures on turbocharged diesel and natural gas engines

5P-8558 Function:

Calibrating Gp. - Pressure Gauge

Used to check or calibrate pressure gauges

- 3 Gauges of 0.5% accuracy with pressure ranges of 1100 kPa (160 PSI), 4150 kPa (600 PSI) and 34,500 kPa (5000 PSI) - Two lower pressure gauges protected from excessive pressure by two sensor valves - A separate source of pressure is required to actuate the calibrating group

6V-7830 Function:

Tetragauge

General purpose device for measuring hydraulic or air pressure

- Functions as general purpose pressure measurement device - Capable of measuring hydraulic or air pressure - Range -100 kPa (-14.5 psi) to 40,000 kPa (+5800 psi). - 8T-5324 Repair Kit available to service this device

1U-7318 Function:

Continuity Tester / Flashlight

Used as a flashlight or continuity tester

- Allows user to test continuity - Can be used as flashlight - High impact plastic - Magnet allows hands free use

5P-7277 Function:

Tester - Voltage

Used to make quick checks for presence of voltage

- Used to make quick checks for presence of voltage - Indespensable for checking out circuits, relays, bulbs, wires, & switches - Designed for voltage range from 12 to 36 Volts - Bulb lights brightly when connected to 36 Volts and dims progressivly with lower voltages - Uses standard 8D-1429 Bulb


Page 10 of 24


8T-0500 Function:

Light - Continuity Testing

Used to test for non-energized or open circuits

- Used to test non-energized circuits; lamp comes on brightly when connected across low resistance circuit - Designed for rugged field use - Comes with light bulb (6V-3061) and 2 N Size batteries (4c-8363) - Replaces canceled 8S-4627 Circuit Continuity Tester

177-2330 Function:

Digital Battery Analyzer

Used to evaluate the condition of 6 & 12 volt batteries

- Automatically Tests 6V & 12V Batteries - CE Compliant - Analyzer Checks for State-of-Charge, Condition, and Voltage - Batteries are Tested in the Machine - No Need to Remove - Temperature compensating circuit for cold batteries - For more information, see PELJ0037 IRM & NEHP6014 Datasheet

4C-4911 Function: -

Battery Load Tester

Heavy Duty Battery Tester used to test 6, 8, & 12 volt batteries

Two, easy to read LCD Displays show accurate measurements of Voltage & Current Voltage measured to one hundredth of a volt for accurate readings Heavy-Duty carbon pile, leads, and clamps - 1000 Amp Load Capacity Fan cooled, internal fan turns on when load is applied For more information, see NEHS7633 Special Instruction

4C-6600 Function:

Battery Voltmeter

Measures battery voltage to determine state of charge

- Designed to quickly determine voltage state of battery 6 - 60 Volts DC - Easier and faster than using a hydrometer to measure specific gravity - Battery voltage is displayed on a bright, red LED display

1U-7297 Function: -

Checks coolant freezing point and battery charge condition (degrees F)

Temperature Comensated Can be used on either hot or cold radiators Can also accurately check some types of permanent antifreeze, such as Dowtherm 209 Alternative Tool: 1U-7298 Coolant and Battery Tester (degrees C)

1U-7298 Function: -

Coolant and Battery Tester

Coolant and Battery Tester

Checks coolant freezing point and battery charge condition (degrees C)

Temperature Comensated Can be used on either hot or cold radiators Can also accurately check some types of permanent antifreeze, such as Dowtherm 209 Alternative Tool: 1U-7297 Coolant and Battery Tester (degrees F)


Page 11 of 24


121-9588 Function:

Removal Tool (16 Gauge TXL)

Removes wires from 40 & 70 pin connectors

- Replaces 121-9587 Removal Tool - For more information, see SEHS9615 Special Instruction

151-6320 Function:

Removal Tool (SXL/GXL)

Removes pins and sockets from Deutsch & AMP connectors

- For more information, see SEHS9615 Special Instruction

175-3700 Function:

DT Connector Service Kit

Used to service and repair Deutsch "DT" type connectors

- Used to maintain and repair Deutsch DT style connectors (Square & Rectangle) on electronic engine harnesses - For more information, see SEHS9615 Special Instruction

190-8900 Function:

HD Connector - Field Service Kit

Used to service Deutsch HD type connectors

- Used to maintain and repair Deutsch HD style connectors (Round) on electronic engine harnesses - For more information, see SEHS9615 Special Instruction

124-5643 Function:

3-Pin Packard Break-Out Cable

Provides test points for individual wires in wiring harness

- Provides voltage test points for individual wires in electronic engine control systems - Used on 3119 HEUI in GM Highway Trucks - Used with 146-4080, 6V-7070, & 9U-7330 Digital Multimeters

125-3662 Function:

Cable - Sensor Bypass

Used to isolate and test sensors for faults

- HEUI bypass cable used to isolate & test sensors for faults


Page 12 of 24


127-6359 Function:

Cable As. - Adapter HEUI Injector

Used to test injector and/or injector harness

- Used to test injector and/or injectory harness - Allows wiring to an individual injector to be bypassed - Helps to isolate problem between injector or harness

129-2018 Function:

Cable As. - Power

Provides access to data link from 40-pin ECM and powers service tools

- Allows power & communication to an ADEM II ECM when vehicle voltage is unavailable

134-5195 Function:

Cable As. - Adapter (40 pin)

Adapts 7X-1715 Cable Assembly to a 40-pin CD-keyed connector

- 40 pin square C/D to A/B adapter cable. - Allows connection of 7X-171 Square A/B 40 pin to 3500 & 3600 engines

139-4166 Function:

(CAT/ATA) Universal Cable

Connects ATA data-link or the CAT (CDL) data-link to 7X-1700 Comm Adapter

- Used to connect either the ATA Data-link or the Cat (CDL) Data-link to the 7X-1700 CA I - Replaces cancelled 7X-1412 Cable Assembly and 7X-1570 Cable Assembly - Can be used with 171-4400 Communications Adapter II for ATA & CDL only

140-2266 Function:

Cable As. - 70 Pin

Provides wire test points for electronic engine control system (ECM)

- Used to provide test points for individual wires in engine wiring harness - Harness has standard probe tips which allow technician to check signal - Used to test signal on limited circuits

143-4508 Function:

Cable - Timing (G3408C)

Used to check ignition timing

- Allows user to check engine timing via timing light & flywheel marks on G3408C Gas Engine - Allows check of primary signal going to each transformer - Cable installs between ignition wiring harness and valve cover connector - Used with 146-4080 or 9U-730 Digital Multimeter


Page 13 of 24


143-4509 Function:

Cable - Timing (G3412C)

Used to check ignition timing

- Allows user to check engine timing via timing light & flywheel marks on G3412C Gas Engine - Allows check of primary signal going to each transformer - Cable installs between ignition wiring harness and valve cover connector - Used with 146-4080 or 9U-730 Digital Multimeter

157-4829 Function:

Cable As. - Adapter

Under dash conversion harness for Freightliner

- Connects 139-4166 Diagnostic Cable to J1939 under-dash diagnostic connector - 9 Pin to J1939 Adapter Cable

163-5443 Function:

Harness - Detonation Sensor

Used to measure condition of detonation sensor

- Allow user to determine condition of detonation sensor on 3400, 3500, & 3600 Gas Engines - For more information, see Page 13, May 1999 Engine News, "Testing Detonation Sensor For Proper Use" - Used with 146-4080, 9U-7330, or 6V-7070 Digital Multimeter

167-9225 Function:

Harness As.

Provides access during cranking to ECM with 70-pin Data Link

- Attaches to the ADEM 2000 Engine harness connector or auxillary battery to service machine without power - Same as 129-2018, except for use with ADEM III - Required to bench flash the ADEM III ECM

196-0055 Function:

Cable - Serial

Connects Communication Adapter II to PC

- Serial PC Cable connects 171-4400 Communications Adapter II to PC 7.62 m (25 ft) - Part of 171-4400 Comm Adapter II Group

1U-9710 Function:

Adapter Cable

Used with Mulitach to measure engine RPM

- Used with 6V-2100 Multitach, 6V-3121 Multitach Group, 9U-7400 Multitach Group, and 6V-9060 Spark Timing Adapter Group


Page 14 of 24


207-6845 Function:

Communications Adapter Cable

Connects communications adapter to engine

- Short Data Link Cable 51 cm (20 in) - Use with ATA, CDL, & J1939-1 - Part of 171-4400 Communications Adapter II Group - Works with cancelled 7X-1700 & 171-4400 Communications Adapters - Replaces cancelled 160-0133 Cable

208-0059 Function:

Cable Assembly

70 Pin Breakout T Cable Assembly

- Used to provide test point for all individual wires in Engine wiring harness of ADEM III - Connects between ECM and main wiring harness - Allow testing access to all 70 wires

7X-1395 Function:

Adapter - SI TDC

Allows 7X-1695 Cable to be used on industrial and gas engines

- 2 Pin Deutsch DT TDC Calibration Cable - Used with 7X-1695 cable to allow connection to TDC adapter for S. I. Engines

7X-1425 Function:

RS-232 Cable

Connects 7X-1701 Communications Adapter to RS-232 computer port

- Used to connect cancelled 7X-1700 Communications Adapter I to RS-232 Port on PC

7X-1686 Function:

Adapter Cable

Adapts on-highway truck 6 pin connector to 9 pin com adapter cable

- ATA in-cab adapter from 139-4166 (9 Pin) to under-dash 6 Pin connection

7X-1688 Function:

Cable Gp.

T-adapter for ECAP and DDT

- Cable connects 7X-1700 Communicaitons Adapter I to RS-232 - Item #2


Page 15 of 24


7X-1695 Function:

Cable - TDC

Allows magnetic timing sensor to be connected to engine ECM

- Used on captive engine applications - Allows magnetic sensor to be connected to engine to input timing information to ECM - Used with 7X-1395 cable to allow connection to TDC adapter for S. I. Engines - Used with 8T-8697 ECAP & 7X-1400 DDT

7X-1714 Function:

Cable - 3116 Engine Adapter

Adapts under dash Packard Connector to communications adapter

- Cable used to connect 139-4166 Communication Adapter harness to under-dash Packard connector - Used with 7X-1700 Communications Adapter I & 171-4400 Communications Adapter II Gp.

7X-1715 Function:

Cable As. - Small (40 Pin)

Provides tests points for individual wires in wiring harness

- Square 40 pin A/B Breakout Cable allowing voltage checks on any wire or between wires - Makes troubleshooting of electronic engine control systems faster & easier - Use with 146-4080, 9U-7330, or 6V-7070 Digital Multimeters

7X-6370 Function:

Adapter Cable As. - 3 Pin DT

Provides test points for wiring harness to faciliate troubleshooting

- Used to service 3406 PEEC and 3176 engines - Provide test points for individual wires in wiring harness - Used with 146-4080, 9U-7330, & 6V-7070 Digital Multimeters

8T-8694 Function:

Adapter Cable As. - 5 Pin


- Used for servicing 3406 PEEC & 3176 Engines - Allows user to troubleshoot engine control system by providing test points - 5 Pin Breakout Adapter Cable Assembly - For use with 8T-8697 ECAP

8T-8695 Function:





Page 16 of 24


8T-8726 Function:




9X-0248 Function:

Adapter Cable As. - Transducer


- Used when servicing 3176 Engines - Allows user to perform electrical measurements on electronic engine controls - For use with 8T-8697 ECAP

9X-1160 Function:



- 40 Pin Breakout Adapter Cable for use on 3176 Engines

6V-2012 Function:

Gauge Gp. - Micrometer Depth

Measures depths up to 230 mm (inch scale)

- Inch Measurement - Contains complete set of measuring rods from 0-228.8 mm (0-9 in) stored in wooded case - Base is 76.2 mm (3 in) wide and uses 3.96 mm (5/32 in) rods.

6V-2034 Function:

Adapter

Used to measure engine valve lip thickness

- Used with the 6V-7059 Multiple Anvil Micrometer

6V-6042 Function:

Point Gp.

Contact points for the dial indicators (2.18 to 120.5 mm long)

- For use with 8T-1000 Electronic Position Indicator & 6V-7926 Dial Indicator - Has plastic box with divided tool holder, space to cut more slots for storage of extra points - Part numbers and sizes are shown on a chart inside the lid of the box. - Will fit all dial indicators with 4-48 thread


Page 17 of 24


6V-7030 Function:

Gauge Gp. - Micrometer Depth

Used to measure depths up to 230 mm (metric scale)

- Millimeter Measurement - Contains complete set of measuring rods from 0-228.8 mm (0-9 in) stored in wooded case - Base is 76.2 mm (3 in) wide and uses 3.96 mm (5/32 in) rods.

6V-7059 Function:

Multiple Anvil Micrometer

Measures cylinder liner top flange thickness and valve lip thickness

- Micrometer used for measuring top flange thickness on cylinder liners - Used with 6V-2034 Adapter to measure valve lip thickness

6V-7926 Function:

Dial Indicator Gp.

Used to measure off-engine timing and other depth measurements

- Use primarily for measuring off-engine timing dimensions when setting fuel pump lifters - Measurements are made with 25.4 mm (1 in) travel indicator and 5 contact points - Can also be used for accurate depth measurements up to 127 mm (5 in)

8T-0450 Function:

Thread Identification Kit

Used to determine thread sizes

- Available to help determine thread size - The size of internal port threads, external adapter threads, and bolt threads can be measured with the tools in this kit - Works on Metric, BSP, and US Standard Threads

6V-2196 Function:

Microscope

Pocket 20X microscope for general inspection

- 20X microscope is recommended for checking crankshaft bearing surfaces - Accurate measurement is provided by a scale reading in 0.1mm increments - Used with 6V-6059 Microlite

6V-6059 Function:

Microlite

Provides a light source for the inspection microscope

- Penlight used with 6V-2196 20X General Usage Microscope - Includes 6V-3061 Bulb - Requires 1U-9535 AAA Batteries (2)


Page 18 of 24


198-4240 Function:

Digital Pressure Indicator

Measures Pressure, Vacuum, Differential Pressure, & Temperature

- Quickly & easily determine system pressures, vacuum, differential pressure, & temperature - Easily locate pressure spikes with Min/Max function - Resolution to 1 psi/bar - Greater accuracy than standard handheld gauges - Recalibrates sensor with each use - CE Compliant - For more information, see PELJ0060 IRM, NEHP6021 Datasheet, & NEHS0818 Manual

6V-9060 Function:

Adapter Gp. - Spark Timing

Checks dynamic timing on gas engines

- Used with 8T-5300 Timing Indicator required for 3304, 3306, & 3516 Engines

8T-5300 Function:

Indicator Gp. - Timing

Used to measure fuel injection timing

- Used to measure fuel injection timing for diesel engines - Checks operation of auto timing advance on euipped engines - Requires 8T-5301 Diesel Timing Adapter or 6V-9060 Spark Timing Adapter - Replaces 6V-3100 Timing Indicator Gp.

8T-5301 Function:

Adapter Gp. - Diesel Timing

Used to measure fuel injection timing on diesel engines

- Required for 300, 1100, 3200, 3300, & 3400 Series Engines - Used with 8T-5300 Timing Indicator Gp.

131-5050 Function:

DataView Gp.

PC based diagnostic tool that measures and records engine parameters

- Has data logging capabilities - Works on ALL Caterpillar machines, new & old - Uses standard Cat sensors and replaces 15+ green sensor boxes - For more information, see NEHS0662 Tool Operating Manual & NEHP6016 Datasheet - Measures and records information from sensors installed on machine or engine - CE Compliant - Does not include PC or sensors

131-5051 Function:

DataView TechStation Gp.

PC based diagnostic tool that measures and records engine parameters

- Has data logging capabilities - CE Compliant - Uses standard Cat sensors and replaces 15+ green sensor boxes - Measures and records information from sensors installed on machines and engines - Includes all accessories needed to operate DataView on a PC except sensors - For more information, see NEHS0662 Tool Operating Manual & NEHP6016 Datasheet


Page 19 of 24


154-8101 Function:

Fuel Flowmeter Gp.

Measures diesel engine fuel burn rate on 3408/12E, 3500

- Display not included - State-of-the-art gear-type flowmeters with temperature compensation - +/- 0.5% accuracy per flowmeter - Prevents starvation if plugged - For more information, see PELJ0021 IRM & NEHS0697 & NEHS0698 Tool Operating Manual -Additional Components: 1U-5306 Hose Gp, 8T-9820 Power Spply, 5P-7366 Power Cable

154-8102 Function:

Fuel Flow Measurement System

Measures diesel engine fuel burn rate on 3408/12E, 3500

- Display included - Prevents starvation if plugged - State-of-the-art gear-type flowmeters with temperature compensation - +/- 0.5% accuracy per flowmeter - Used with 154-8106 Fuel Flow Display - For more information, see PELJ0021 IRM & NEHS0697 & NEHS0698 Tool Operating Manual

168-7730 Function:

Fuel Flowmeter Gp.

Measures diesel engine fuel burn rate on 3600

- +/- 0.5% accuracy per flowmeter - Prevents starvation if plugged - 3612 & 3616 engines require accumulators - Used with the 8T-9300 Fuel Flow Monitor, 9U-7400 Multitach, or 131-5051 DataView - For more information, see PELJ0033 IRM & NEHS0740/NEHS0741 Tool Operating Manual

168-7740 Function:

Fuel Flow Measurement System

Measures diesel engine fuel burn rate on 3606, 3608, 3612, & 3616

- Inlcudes 154-8106 Fuel Flow Display - +/- 0.5% accuracy per flowmeter - Prevents starvation if plugged - 3612 & 3616 engines require accumulators - For more information, see PELJ0033 IRM & NEHS0740/NEHS0741 Tool Operating Manual

179-0710 Function:

Burn Rate Meter (With Display)

Used to measure engine burn rate on 3116, 3126, C-9, 3208, 3304, 3406/08

- Includes 154-8106 Fuel Flow Display - Flowmeter burn rate: 4 LHP (1.05 GPH) to 260 LPH (69 GPH) - Flowmeter Accuracy: +/- 1% of reading, +/- 0.1 GPH - Flowmeter type: Positive displacement, piston. Temperature compensated & output scaling - For more information, see PELJ0042 IRM & NEHS0776

179-0711 Function:

Burn Rate Meter (No Display)

Used to measure engine burn rate on 3116, 3126, 3176, 3208, 3304, 3406/08

- Does not Include 154-8106 Fuel Flow Display - Flowmeter burn rate: 4 LHP (1.05 GPH) to 260 LPH (69 GPH) - Flowmeter Accuracy: +/- 1% of reading, +/- 0.1 GPH - Flowmeter type: Positive displacement, piston. Temperature compensated & output scaling - For more information, see PELJ0042 IRM & NEHS0776


Page 20 of 24


143-4062 Function:

Sensor - Pressure (100 psi)

Pressure sensor for use with DataView

- 0 to 689 kPa (0 to 100 psi) - Used with 131-5050 or 131-5051 DataView Gp. - For more information, see NELG5023 Sensor List - Low cost

143-4065 Function:



- 0 to 6890 kPa (0 to 1000 psi) - Low cost - Used with 131-5050 or 131-5051 DataView Gp. - For more information, see NELG5023 Sensor List

143-4066 Function:



- 0 to 51675 kPa (0 to 7500 psi) - Low cost - Used with 131-5050 or 131-5051 DataView Gp. - For more information, see NELG5023 Sensor List

153-9630 Function:

Test Gp. - Sensor

Used to test CAT ® PWM and analog sensors

- Kit Includes: 153-9625 PWM Sensor Adapter - CE Compliant 153-9626 Break-Out Cable-HD 153-9627 Break-Out Cable-DT - Allows user to T into existing Cat sensors for measure and record using DataView - For more information, see NELG5023 Sensor List & PELJ0009 IRM

1U-9139 Function:

Universal Fuel Line Pickup

Used with multitach or DataView to measure engine speed

- Item #1 - Used with 6V-2100 Multitach, 131-5050 or 131-5051 Dataview Gp.

6V-4950 Function:

Pickup Gp. - Injection Line Speed

Used with multitach to measure diesel engine speed

- Mounts to fuel line to measuer fuel pulses to determine RPM - Works on Perkins fuel lines as well as those with remote unit pump group - Works on precombustion chamber fuel systems & on some smaller direct injection systems - Used with 9U-7400 Multitach II & 131-5050 DataView - For more information, see SEHS8029 Special Instruction


Page 21 of 24


8T-5184 Function:

Transducer - 1/4" Dia x 3.5"

Fuel line pressure transducer

- Used with 8T-5300 Timing Indicator Group - Shorter (0.5") than the 6V-2197 transducer - [8.9 cm (3.5 in) long

8T-5185 Function:

Transducer - 1/4" Dia.x 7"

Fuel line pressure transducer

- Used with 8T-5300 Timing Indicator Group - Longer (2.5") than the 6V-2197 transducer - 17.8 cm (7 in) long

1P-3537 Function:

Dial Bore Gauge Gp. (Inch)

Used to measure bore diameters (50.8 to 203.2 mm dia.)

- Useful for making critical bore measurement from 50.8 mm (2 in) to 203.2 mm (8 in) - Used to reconditioning cylinder bores on 1100 & 3100 series engines - Used to refinish connecting rods in 137.16 mm (5.4 in) bore V8 & V12 engines - Item #2 - See T&SPG (NENG2500) for other available models

5P-2170 Function:

Dial Bore Gauge Gp.

Used to measure bore diameters (19.05 to 38.10 mm)

- This gauge and its related masters provides accuracy to.0025 mm (.0001 inch) for measuring all bores in the size range 19.05-38.10 mm (.750 inch to 1.500 inch). - Particularly useful for measuring the relief valve spool bores in pressure control bodies on 631, 633, 637, 641,650, 651, 657, 660, and 666 Tractors with eight speed transmissions. - See T&SPG (NENG2500) for other available models

6V-6000 Function:

Dial Bore Gauge (metric)

Used to measure bore diameters (30.0 to 50.8 mm)

- Item #2; Used with 6V-6030 Size Setting Fixture (Item #1 - See T&SPG (NENG2500) for other available models

6V-6030 Function:

Size Setting Fixture

Used to calibrate or check dial bore gauges (30.0 to 50.8 mm)

- A precision measuring instrument with a diameter range of 30 - 50.8 mm (1.2 - 2 in) graduated to 0.002 mm (.00008 in) increments - Item #1 - Used with 6V-6000 Dial Bore Gauge (Item #2) - For more information, see SMHS8036 Special Instruction


Page 22 of 24


6V-7897 Function:

Dial Indicator

Converts dial bore gauge to metric

- Dial Indicator used to convert 1P-3535 Dial Bore Gauge to the 6V-7898 Dial Bore Gauge - Used with 1P-3535 Dial Bore Gauge

6V-7898 Function:

Dial Bore Gauge - Metric

Measures internal diameters (50 to 200 mm) & depths (13 to 300 mm)

- The dial bore gauge and size setting fixture will measure all internal diameters from 1.97 inch to 7.87 inch (50 to200 mm) and depths from 0.51 inch to 11.81 inch (13 to 300 mm) in increments of 0.00008 inch (0.002 mm). - Used with 6V-7899 Size Setting Fixture - See T&SPG (NENG2500) for other available models

6V-7899 Function:

Size Setting Fixture - Metric

Used to check or calibrate the dial bore gauges

- Used with 6V7898 Dial Bore Gauge - For more information, see SMHS8254 Special Instruction

123-6471 Function:

M300 Diagnostic Tool Group

Used to setup, test, calibrate, & troubleshoot M300 Series Wheeled Excavators

- Tester will display readings from both engine control and pump control systems - This hand-held tool features a 4 line, 16 character liquid crystal display (LCD) - For more information, see SEHS9825 Special Instructions, SENR6261 Test & Adjust Manual

125-2580 Function:

Tool Gp. - HEUI Engine

Troubleshoots electrical and hydraulic systems

- HEUI Diagnostic Tooling - Includes all necessary cables, harnesses, & pin removal tools - Injector and IAPC valve removal & installation tools - Modified injector clamp to aid in proper assembly and tightening of jumper tube - Necessary bit drivers and socket to work on hard-to-reach components - New double ended offset feeler gauge for setting valves

148-9610 Function:

Mobile Diagnostic PC Cart

Used to hold PC, monitor, printer and DataView hardware

- Durable painted steel with fiberglass top - Storage for up to 30 CDs in the door - PC installs inside with cooling fan - Internal power stripes provided - For more information, see NEDG6001 Datasheet & PELJ0013 IRM - CE Compliant - 150-8756 is 220V alternative cart


Page 23 of 24


8C-9801 Function:

Signal Adapter Gp. - PWM

Measures frequency and duty cycle of pulse width modulated signal

- Provides additional function to measure frequency and duty cycle of PWM signals - Allows user to verify or diagnose operation of some sensors on electronic engines - Used with 8T-8697 Analyzer Programmer (ECAP)

8S-2257 Function:

Eye Loupe

Eye loupe with 12X power

- 12 X Power - 25.4 mm (1 in) Depth - Extremely Portable

9U-6695 Function:

Indicator - Spark Plug Firing

Indicates spark plug firing

- Adjustable sensitivity - user can set firing indicator to flash when placed near primary wire on exposed coils of 6.25 inch bore engines - Reliable tool to diagnose ignition problems - Flashing LED indicator easily seen in daylight

9U-7554 Function:

Printer Gp. - Portable (110 VAC)

Used to make hard copy records of various diagnostic information

- Standard RS-232 Portable Field Printer - Used with 8T-8697 ECAP

9U-7560 Function: -

Field Soldering Iron Gp.

Used to solder electrical connections (battery powered)

12V Cigarette Connector Field Soldering Iron Used with 4C-9024 Battery Pack Gp. or 12 volt source In line fuse prevents damage and/or overload For more information, see NEHS0601 Tool Operating Manual


Page 24 of 24

Herramientas de Diagnostico Caterpillar

Recommend Documents