Quick reference guide SD Central Controlling Device
I. Introducti I ntroduction on SD is quite easy to operate. The way to operate it is similar to cell phones. The function of Key 1 and Key 2 are correspondingly as the indication in the lower-left and the lower-right on the LCD. Thus you can operate it according to the words on LCD easily. easily. In order to facilitate the use of the central controlling device, SD central controlling device upgrades many advanced designs. It applies SD card as the vector to update data of the system. A USB interface and a piece of SD card can be availed to update the data in the central controlling device easily. Humming is a hint for the button setting. If the humming doesn't work, it means the key isn't pressed yet. Front operating table is shown as fig.1.1.
Fig .1.1 The front operation table of the SD Central Controlling Device
1. Function Selecting
Select and confirm the menu function. The function is corresponding to the
indication in the lower-left of the LCD screen. Key 1 can be used to unlock the keyboard too. 2. Cancel and Return
Quit the present task and back to the menu one level up. The function is
corresponding to the indication in the lower-left of the LCD screen. 3. Page up
Browse the pages ahead.
4. Page down
Browse the pages below. below. Key 4 can also be used to unlock the keyboard.
5. Shift Up / Down 6. Trigger SOS
Shift between the uplink and downlink information.
If “SOS=2”（shown in System Parameter）,the key is used to trigger the function of SOS; if ”SOS=3”,the key need to work with external switch to trigger the function of SOS.
7. SD card interface 8. Photosensitive Probe 9. Direction indicator
II. Operation of the Function Menu The description hereinafter are about the operation of the function menu of the SD Central Controlling Device. Please connect the central controlling device to the LED screen. The interface of the central controlling device will be introduced in Part III. 1. Unlock the Keyboard
In order to work properly, this central controlling device has been set with automatically locking function. Keyboard should get unlocked after long-term stand-by before you use it. Press Key 1 and then press Key 4 will unlock the keyboard. Caution!
Shift Up / Down is also available even if the keyboard is locked. The LCD indication (lock
and unlock) are shown as fig.2.1.1 (the line information is for reference only)
228 UP FC3 R LOCK
→
S
228 UP FC3 FUN
In
Lock
→
R
S
In LIST
Unlock Fig.2.1.1 Diagram of unlocking the keyboard
2. Update the lines date
Copy the data file of the lines (files with extension name td5) to the top level directory of the SD card by using card reader. And then insert the SD card into the SD card slot. Press F1 to enter the function menu after unlocking the keyboard. The prompting message of the menu to update the lines date is shown as fig.2.2.1.
-----FUNCTION---Download Route
SELECT
EXIT
Fig.2.2.1 Update the Table of Lines While the lines need to update, press Key 1 and enter the function of updating lines date. Then you will find “select rute file”and prompt message for the file name of data files. (If there isn 't data file in the SD card or data files aren’t in the top level directory, it will be error and displays error message.) Shown as fig.2.2.2.
Download Route Select Route 12.td5 SELECT EXIT Select the File of Lines
-----FUNCTION---no Route file
RETURN SD Card without the File of Lines
-----FUNCTION---Init Failure Please Retry RETURN
Download Route Download OK OK
No Card Inserted
Successful Updating
2.2.2 Updating the Line Information Enter the SD card information, and then select the files which you want to update in the Lines Table by using Page Up / Down. Press Key 1 to confirm the file you select. You can check the updating progress with the progress bar. The prompt message “Download OK”will be displayed when updating ends. Press Key 1 to confirm and quit Caution!
Please make sure the SD card insert into the SD card slot during the process of updating. Draw
out the SD card when the updating ends up. In addition, due to the limitation of the LCD size of the central controlling device, data file names with overlength cannot be overall displayed on the LCD screen. In order to display the overall file names, you'd better not name it wi th a long name. 3. Query Board Hard
In this function list, the ways to operate the eight submenus "Front", "Rear Inter", "Inter", "Side3","Side2","Rear Side","Side"and "Rear" are exactly the same. Take the "Front" as an example. Connect the central controlling device to the anterior board (interface and ways to connect it will be introduced in Part III). And then turn to page“Query Board Hard”and press Key 1 to enter the "Front". Press Key 1 again and select " Query ", you will see the version of the size and software and hardware information of the LED board. Press Key 2 to return. shown as fig.2.3.1.
-----FUNCTION---Query Board Hard
SELECT
EXIT
Query Board Hard Front Query
Return
FrontL:112 H:016 C1A1 M8S6 ANNV5.0 16120423 064KB MAX Return
2.3.1 4.Check Connect
Turn to page”Check Connect”and press Key1 to enter the state of Board connecting,which is shown as:
Check Connect
→
F C3 RETURN 5. Set LCD Contrast
Turn to page“set LCD contrast”and press Key 1 to enter the state of setting LCD contrast. Which is shown as fig.2.5.1.
-----FUNCTION---set LCD contrast
SELECT
set LCD contrast press ‘+’’-‘ ENTER RETURN
EXIT Fig.2.5.1.
LCD Contrast Setting
Press Key 3 to increase the LCD contrast, Key 4 to decrease LED contrast brightness. Press Key 1 to confirm and quit. Caution!
The contrast of the LCD is capable of meeting the users' demand. Users’ resetting this item is
not encouraged. 6. System Parameter
Turn to page“Sys Parameter”in function list, and then press Key 1 to check the
system information. Press Key 2 to go back to the previous level. The inquiry for system parameter information is shown as fig.2.6.1.
-----FUNCTION---Sys Parameter
SELECT
Sys Parameter TP-02 1A1 SOS=2 TPLV5.0 111004 RETURN
EXIT
Fig.2.6.1. Inquiry for System Parameter Information 7. Update Firmware
Copy the data file of the Hardware Setting Center Controller (files with extension name tdh.) to the top level directory of the SD card by using card reader. And then insert the SD card into the SD card slot. Press F1 to enter the function menu. The prompting message of the menu to update firmware is shown as fig.2.7.1. Caution! The top level directory of the SD card must have one and only one data file of the Hardware
Setting Center Controller. If not , when updating firmware, the fist copy file will be called only.
-----FUNCTION---Update Firmware
SELECT
EXIT
Update Firmware 00
Update Firmware 11
Update Firmware no .tdh document
SET
SET
TLC-1
RETURN
Update Firmware
RETURN Code 11
20110129
No program file or program file can’t be found in the top directory
Update Firmware SD Error
Update Firmware document error 1
Update Firmware Updating
TLC-1
TLC-1
TLC-1
20110129
20110129
20110129
Fig.2.7.1 8. Adjust the Lines
Press Key 2 to enter the table of Lines in the top level menu (the menu unlocked). Select the line name you will set as the present line by using Page Up / Down key. Press Key 1 and select “DETAIL”, and then press Key 1 to select “HANDLE". At last press Key 1 to confirm and quit. Prompt messages are shown as fig.2.8.1.
228 UP F R FUN
→
S
228 567 SOS DETAIL
In
Top level directory
Page up / down to select lines
228 UP
Set Current?
HANDLE
EXIT
RETURN
ENTER
Select lines
RETURN
Set as the present line
228 UP F R LOCK
→
S
In
Lines adjusting done
Fig.2.8.1. Adjust the Lines 9. Shift between the uplink and downlink
Key 5 is available for you to shift between the uplink and downlink. Shift Up / Down is also available even if the keyboard is locked.
