A3 UV Printer Manual.pdf

A3 UV Printer Manual

Directory

A machine diagrams diagrams Front of the machine

A machine diagrams Two safety guidance Install three machines Four printer driver installation and settings Five printer driver Help Six SpringShine RIP installation and set up

Seven treatment before printing graphic Eight printout Nine routine maintenance and maintenance machinery Ten Troubleshooting Eleven machine transport considerations Twelve other issues

3

2

The back of the machine

The right side of the machine

Control Panel

The left side of the machine

取消按键确认按键抽墨按键信息指示灯连线按键平台进按键

复位按键清洗按键平台微调上平台上升按键平台出按键平台下降按键

平台微调下

4

5



Control Panel




平台微调下

5

4

Key Description: 1 .Connect button: the equivalent switch. Click Connect, online lamp lights, the machine online; then click is shut down, the online light goes off, the machine shut down. 2 .platform into the button: Press the platform forward. 3 .platform back buttons: Press the platform returned. 4 .platform rises button: Press platform increased. 5 .on the platform to fine-tune: Press the trimming rise (for trimming height). 6 .platform fell button: Press the platform fell. 7 .platform fine-tuning: Press the spinner fall (for trimming height). 8 .Automatic Keys: Press then automatically returned to the starting position of the platform. 9 .Reset button: Press, Mexican trucks move to the left, and then reset (if the print button is pressed, the machine will cancel the print job, stop printing). 10. cleaning button: Press for 3 seconds, the machine will print head cleaning. White ink tank and agitation button

6

Other parts of the presentation

7



Control Panel




平台微调下

5

4


6


7



7

6

Two safety guidance ！

Please carefully read all of these instructions before using this equipment. Also, be sure to follow the label on the printer all warnings an d tips.

When you select this device placement

* Let your entire computer system away from potential sources of electromagnetic interference, such as speakers Or cordless telephone base. * Use only the power source indicated on the device label type.

* This equipment on a stable countertop area larger than the product of the base. If you play Printing a certain inclination angle, it can not work properly.

* Do not use a damaged or frayed power cord.

* Avoid placing in temperature and humidity prone to dramatic changes in place. In addition, playing Printer to avoid direct sunlight, strong light, or heat.

* Do not put your hand into the device or touching dangerous parts of this circuit, when printing.

* Avoid places subject to shocks and jolts place. * Do not use this product in a cold or dusty place. * Please proper use / keep this device in order to avoid the use / improper storage (such as a mouse Damage, liquid ingress, etc.) cause a malfunction and damage. * The best place in the temperature 10 ~ 25 ：, humidity is best controlled at 55% to 65% of the environment When installing this equipment * Do not block or cover the openings on the chassis of this product. * Do not insert any object into the slot of the printer. Be careful not to spill liquids On this device. * This product's power lines, data lines only available for this device. 8

* All equipment must be connected to a properly grounded electrical outlet. Avoid copier Or air conditioning systems that regularly switch devices using a socket in the same loop.

When using this device

* Always use the "Connect" button on the control panel, turn off this machine. When you press thi s button After the connection indicator flashes briefly and then goes out. In the Pause light stops Before flashing, do not turn off the main power or unplug the printer's power cord. About Ink * The ink bottle saved enough to pick the reach of children. * If ink gets on your skin, wash thoroughly with soap and water. If ink gets into your eyes, flush immediately with water and seek medical advice. * After opening the recommendations in the ink color runs out six months, White 2 months, shake well before using. Ink stored in the shade, the temperature is best controlled at 10 ~ 25 ：, and humidity is best controlled at 55% to 65% of a clean place.

9

Two safety guidance ！

Please carefully read all of these instructions before using this equipment. Also, be sure to follow the label on the printer all warnings an d tips.

When you select this device placement

* All equipment must be connected to a properly grounded electrical outlet. Avoid copier Or air conditioning systems that regularly switch devices using a socket in the same loop. * Let your entire computer system away from potential sources of electromagnetic interference, such as speakers Or cordless telephone base. * Use only the power source indicated on the device label type.

* This equipment on a stable countertop area larger than the product of the base. If you play Printing a certain inclination angle, it can not work properly.

* Do not use a damaged or frayed power cord.

* Avoid placing in temperature and humidity prone to dramatic changes in place. In addition, playing Printer to avoid direct sunlight, strong light, or heat.

* Do not put your hand into the device or touching dangerous parts of this circuit, when printing.

* Avoid places subject to shocks and jolts place. * Do not use this product in a cold or dusty place. * Please proper use / keep this device in order to avoid the use / improper storage (such as a mouse Damage, liquid ingress, etc.) cause a malfunction and damage. * The best place in the temperature 10 ~ 25 ：, humidity is best controlled at 55% to 65% of the environment When installing this equipment * Do not block or cover the openings on the chassis of this product. * Do not insert any object into the slot of the printer. Be careful not to spill liquids On this device. * This product's power lines, data lines only available for this device.

When using this device

* Always use the "Connect" button on the control panel, turn off this machine. When you press thi s button After the connection indicator flashes briefly and then goes out. In the Pause light stops Before flashing, do not turn off the main power or unplug the printer's power cord. About Ink * The ink bottle saved enough to pick the reach of children. * If ink gets on your skin, wash thoroughly with soap and water. If ink gets into your eyes, flush immediately with water and seek medical advice. * After opening the recommendations in the ink color runs out six months, White 2 months, shake well before using. Ink stored in the shade, the temperature is best controlled at 10 ~ 25 ：, and humidity is best controlled at 55% to 65% of a clean place.

9

8

Install three machines Keep the device Precautions Please read the "Safety Instructions", placed after a good machine, install the machine in the following order: First, connect the power cable, data cable. (Tip: Use the power according to th e type of power source indicated on the label)

Power line

10

Ink numbers

Data line

Second, the correct boot Turn on the power switch, and then press the "Connect" button on the control panel. (Boot print platform will come to the en d of the outermost)

Open the main power switch

Third, install the ink Open the ink tank, the ink into the ink bottles in the warehouse. Press the number corresponding to the color of the ink tube plus on ink, numbered 1 and yellow (Y), No. 2 plus magenta (M), No. 3 Garland color (C), No. 4 plus black (K), No. 5, 6,7,8 is white (W).

Installation open the bottle of ink

Click "Connect" 11

Install three machines Keep the device Precautions Please read the "Safety Instructions", placed after a good machine, install the machine in the following order: First, connect the power cable, data cable. (Tip: Use the power according to th e type of power source indicated on the label)

Power line

Ink numbers

Data line

Second, the correct boot Turn on the power switch, and then press the "Connect" button on the control panel. (Boot print platform will come to the en d of the outermost)


Third, install the ink Open the ink tank, the ink into the ink bottles in the warehouse. Press the number corresponding to the color of the ink tube plus on ink, numbered 1 and yellow (Y), No. 2 plus magenta (M), No. 3 Garland color (C), No. 4 plus black (K), No. 5, 6,7,8 is white (W).

Installation open the bottle of ink

Click "Connect" 11

10

Fourth, the ink filling ink system Press and hold the button switch and hold the waste ink pump, wait a few minutes until the ink tube out from the waste ink into the waste ink bottle to release the waste ink pump button switch, this time the ink filling ink system has been completed.

Three printer driver installation and settings The printer driver installation The random CD in the drive to copy to your computer, or download the driver from our website to your computer. Then turn off antivirus software, connect the printer cable connected to your computer, and then install according to the following method: 1 R1800 drivers found in the SETUP.EXE file double click to open

Fifth, the proper shutdown Use the "Connect" button on the control panel off this machine. When you press this button After a brief pause indicator flashes and then turns off. Then turn off the power switch. (Before the connection indicator stops flashing, do not turn off the main power or unplug the printer's power cord.)

Click "Connect"

12

2 Select OK to enter the Setup dialog box.


13

Fourth, the ink filling ink system Press and hold the button switch and hold the waste ink pump, wait a few minutes until the ink tube out from the waste ink into the waste ink bottle to release the waste ink pump button switch, this time the ink filling ink system has been completed.

Three printer driver installation and settings The printer driver installation The random CD in the drive to copy to your computer, or download the driver from our website to your computer. Then turn off antivirus software, connect the printer cable connected to your computer, and then install according to the following method: 1 R1800 drivers found in the SETUP.EXE file double click to open

Fifth, the proper shutdown Use the "Connect" button on the control panel off this machine. When you press this button After a brief pause indicator flashes and then turns off. Then turn off the power switch. (Before the connection indicator stops flashing, do not turn off the main power or unplug the printer's power cord.)

Click "Connect"

2 Select OK to enter the Setup dialog box.


13

12

3 choose to accept the license agreement appears.

5 ports available again pop-up dialog, select the top of the first item, then click OK. After waiting for f ile copying, eject the installation is complete, the installation of the driver window off. Complete the installation.

4 In the Print tool options, select Manual. Complete the installation:

14

15

3 choose to accept the license agreement appears.

5 ports available again pop-up dialog, select the top of the first item, then click OK. After waiting for f ile copying, eject the installation is complete, the installation of the driver window off. Complete the installation.

4 In the Print tool options, select Manual. Complete the installation:

15

14

The printer driver setting 1 Locate the "Printers and Faxes" in the desktop Start menu, click Open.

3 Set the following options in the main window

Quality options: high-quality photos Source: single page Type: photo quality inkjet paper Size: A3 +

2 and then to the printer EPSON Stylus Photo R1800, right click the mouse, and then find the "Printing Preferences", click Open.

16

17

The printer driver setting 1 Locate the "Printers and Faxes" in the desktop Start menu, click Open.

3 Set the following options in the main window

Quality options: high-quality photos Source: single page Type: photo quality inkjet paper Size: A3 +

2 and then to the printer EPSON Stylus Photo R1800, right click the mouse, and then find the "Printing Preferences", click Open.

17

16

Click Advanced, continues, there will be no high-speed tick, tick smooth edges Then click OK to save the settings. Setup is complete

Five printer driver Help A nozzle check (print a test page) * Nozzle Check utility checks the print head nozzles are clogged. To ensure print quality, please do every da y in front of the nozzle check print job. Please follow the steps below to use the Nozzle Check utility: 1 Make sure the paper or other media used to print the height of the test, the platform is then reset to the starting position (print height, platform reset, please refer to the "Operating Procedures") 2 Open the printer driver preferences, find maintenance page, click the Nozzle Check icon in the pop-up dialog box, choose the "Print" button to print.

18

19

Click Advanced, continues, there will be no high-speed tick, tick smooth edges Then click OK to save the settings. Setup is complete

Five printer driver Help A nozzle check (print a test page) * Nozzle Check utility checks the print head nozzles are clogged. To ensure print quality, please do every da y in front of the nozzle check print job. Please follow the steps below to use the Nozzle Check utility: 1 Make sure the paper or other media used to print the height of the test, the platform is then reset to the starting position (print height, platform reset, please refer to the "Operating Procedures") 2 Open the printer driver preferences, find maintenance page, click the Nozzle Check icon in the pop-up dialog box, choose the "Print" button to print.

19

18

3 After printing out, see the printed nozzle check pattern. Below are two sample nozzle check pattern: Good examples

Two cleaning the print head Print head cleaning methods are as follows: 1 Open the printer driver preferences, find maintenance page, click on the print head cleaning icon in the popup dialog box, choose "Start" to start cleaning.

The print head needs to be cleaned

If the print head needs cleaning, see "Cleaning the print head" or "machine maintenance."

2 After the cleaning is completed, please do the nozzle check, check the print out of the nozzle check pattern. If the nozzle check page print result is not satisfactory, you may need to repeat the print head cleaning and print the nozzle check pattern again. (Long press "cleansing" on the control panel button for 3 seconds can also be print head cleaning)

20

21

3 After printing out, see the printed nozzle check pattern. Below are two sample nozzle check pattern: Good examples

Two cleaning the print head Print head cleaning methods are as follows: 1 Open the printer driver preferences, find maintenance page, click on the print head cleaning icon in the popup dialog box, choose "Start" to start cleaning.

The print head needs to be cleaned

If the print head needs cleaning, see "Cleaning the print head" or "machine maintenance."

2 After the cleaning is completed, please do the nozzle check, check the print out of the nozzle check pattern. If the nozzle check page print result is not satisfactory, you may need to repeat the print head cleaning and print the nozzle check pattern again. (Long press "cleansing" on the control panel button for 3 seconds can also be print head cleaning)

21

20

Six SpringShine RIP installation and set up (3) the dialog box, select "Next" - "Next" - "Finish" To complete the installation.

A SpringShine RIP installation The CD-ROM supplied in the SpringSun RIP copied to your computer, or download SpringSun RIP from our website to your computer. Then turn off anti-virus software will randomly dongle into your computer, and then i nstall the following methods: 1. The dongle into your c omputer

2 Double-click to open SpringShineRIP_2014_1_24_ new. Exe

22

23

Six SpringShine RIP installation and set up (3) the dialog box, select "Next" - "Next" - "Finish" To complete the installation.

A SpringShine RIP installation The CD-ROM supplied in the SpringSun RIP copied to your computer, or download SpringSun RIP from our website to your computer. Then turn off anti-virus software will randomly dongle into your computer, and then i nstall the following methods: 1. The dongle into your c omputer

2 Double-click to open SpringShineRIP_2014_1_24_ new. Exe

23

22

Installation of two UV curve

Open the software interface as follows:

Copy the CD in random curves A31800uv-20130926.icm file onto your computer, or downloaded from our website A31800uv-20130926.icm onto your computer. Then according to the following method to install: 1 Select the curve, the curve of the mouse right click to copy 2 Copy and paste the following path curves to complete the installation of the curve C: \ SpringShineRIP \ Profile \ CMYK

2 Click to find the corresponding modules, each module parameter settings Each module position

Three SpringShine RIP settings After SpringShine RIP and UV curve installed, the next step is to SpringShine RIP some settings. 1 Double-click the desktop SpringShine RIP (W) Software icon (Note: Please open the front software dongle into your computer; your desktop icons have two SpringShine RIP, one SpringShine RIP, the other one is SpringShine RIP (W), open SpringShine RIP (W) icon)

24

25

Installation of two UV curve

Open the software interface as follows:

Copy the CD in random curves A31800uv-20130926.icm file onto your computer, or downloaded from our website A31800uv-20130926.icm onto your computer. Then according to the following method to install: 1 Select the curve, the curve of the mouse right click to copy 2 Copy and paste the following path curves to complete the installation of the curve C: \ SpringShineRIP \ Profile \ CMYK

2 Click to find the corresponding modules, each module parameter settings Each module position

Three SpringShine RIP settings After SpringShine RIP and UV curve installed, the next step is to SpringShine RIP some settings. 1 Double-click the desktop SpringShine RIP (W) Software icon (Note: Please open the front software dongle into your computer; your desktop icons have two SpringShine RIP, one SpringShine RIP, the other one is SpringShine RIP (W), open SpringShine RIP (W) icon)

25

24

1 Set the layout parameters, the printer is set to the maximum output size width 32.900, 65.000 height.

2 Set Printer Parameters Printer Setup: Stylus Photo R1800 Print port: USB001 Stylus Pro R1800 Paper detection option: ON White and color ink resolution: 1440 * 1440 (generally this setting, the resolution must be consistent both ink, the higher the resolution the better print quality, but slower speed) Paper feed: Standard Print method: unidirectional printing

26

Tip: If there is not set correctly, the printer does not print job

27

1 Set the layout parameters, the printer is set to the maximum output size width 32.900, 65.000 height.

2 Set Printer Parameters Printer Setup: Stylus Photo R1800 Print port: USB001 Stylus Pro R1800 Paper detection option: ON White and color ink resolution: 1440 * 1440 (generally this setting, the resolution must be consistent both ink, the higher the resolution the better print quality, but slower speed) Paper feed: Standard Print method: unidirectional printing

Tip: If there is not set correctly, the printer does not print job

27

26

3.Color Set Color Mode: WWWW + KCMY amount of color ink-jet: 35% (usually set this) ICC Curve: A31800uv-20130926.icm

4.White Set White coat effect: anti-film

Click on "ICC profile", the dialog box is checked using the ICC profile, select A31800uv-20130926.icm, then click OK.

28

29

3.Color Set Color Mode: WWWW + KCMY amount of color ink-jet: 35% (usually set this) ICC Curve: A31800uv-20130926.icm

4.White Set White coat effect: anti-film

Click on "ICC profile", the dialog box is checked using the ICC profile, select A31800uv-20130926.icm, then click OK.

29

28

Seven treatment before printing graphic UV machine easy to operate and provide customers with more print features, such as relief, white, of course, these features also need to look at the picture in order to achieve special treatment.

Next, find the menu bar of the "image", select "Adjust" inside the "Levels" dialog box appears, drag the slider to adjust the Input Levels gloomy picture of the degree (see pictures when you drag, the more black this is the place where representatives of white ink to print, the more shallow the place where white ink printing on behalf of the less), according to t heir own needs after adjustment slider press OK.

Relief map production Relief is relying stacked up white ink, white ink piled higher the more obvious. The machine is to determine how much white ink in which place should be sprayed according to the color shades. So, what part of the print product needs relief, we can be achieved by mapping. In the f ollowing image processing software Adobe Photoshop CS6 example picture im age processing.

1 overall relief Opened with Adobe Photoshop CS6 need to deal with the picture, then click the image menu bar, find patterns, to CMYK mode; then find the menu bar of the "image", select "Adjust" inside "to the color" pictures to color.

Finally, do a picture of another saved as TIFF format

30

31

Seven treatment before printing graphic UV machine easy to operate and provide customers with more print features, such as relief, white, of course, these features also need to look at the picture in order to achieve special treatment.


Relief map production Relief is relying stacked up white ink, white ink piled higher the more obvious. The machine is to determine how much white ink in which place should be sprayed according to the color shades. So, what part of the print product needs relief, we can be achieved by mapping. In the f ollowing image processing software Adobe Photoshop CS6 example picture im age processing.

1 overall relief Opened with Adobe Photoshop CS6 need to deal with the picture, then click the image menu bar, find patterns, to CMYK mode; then find the menu bar of the "image", select "Adjust" inside "to the color" pictures to color.


31

30

2 partial relief Partial relief, meaning the image is to highlight a particular part. For example, the following example highlights the hat to be part of.

Opened with Adobe Photoshop CS6 need to deal with the picture, click on the image menu bar, find patterns, to CMYK mode, then use the Cutout tool to pull out of the hat portion (generally using a pen matting), will be plucked out of the "hat" constituency change layer, then turn off the other layers, select the hat layer. Then find the menu bar of the "image", select "Adjust" inside "to the color" pictures to color.

To color

Pen Tool

Hat made out of layers



32

33

2 partial relief Partial relief, meaning the image is to highlight a particular part. For example, the following example highlights the hat to be part of.

Opened with Adobe Photoshop CS6 need to deal with the picture, click on the image menu bar, find patterns, to CMYK mode, then use the Cutout tool to pull out of the hat portion (generally using a pen matting), will be plucked out of the "hat" constituency change layer, then turn off the other layers, select the hat layer. Then find the menu bar of the "image", select "Adjust" inside "to the color" pictures to color.

To color

Pen Tool

Hat made out of layers



33

32

White map production White figure, meaning that a layer of white ink base map. For example, to print a transparent shell phone, because the bottom is transparent, color pictures, then just print out the effect is not very satisfactory. To obtain more satisfactory results, this time you need to hit a white background.

2 would fill the selection with black, concrete is right in the middle point of the selection, and then choose Fill, choose black content of the dialog box, then OK.

Right-filled

Dialog

After completion of

There are no white brown white transparent shell White map production, with the following image processing software Adobe Photoshop CS6 example image processing. 1. The picture opens, click on the image menu bar, find patterns, to CMYK mode, use the marquee tool to the entire picture becomes constituency.

3 Finally, do a good job of another saved as TIFF

format images

Marquee Tool

Picture becomes constituency

34

35

White map production White figure, meaning that a layer of white ink base map. For example, to print a transparent shell phone, because the bottom is transparent, color pictures, then just print out the effect is not very satisfactory. To obtain more satisfactory results, this time you need to hit a white background.

2 would fill the selection with black, concrete is right in the middle point of the selection, and then choose Fill, choose black content of the dialog box, then OK.

Right-filled

Dialog

After completion of

There are no white brown white transparent shell White map production, with the following image processing software Adobe Photoshop CS6 example image processing. 1. The picture opens, click on the image menu bar, find patterns, to CMYK mode, use the marquee tool to the entire picture becomes constituency.

3 Finally, do a good job of another saved as TIFF

format images

Marquee Tool

Picture becomes constituency

35

34

Guides As the front of the head has the installation of UV light, so the need to reserve the position lights installed, you need to print the picture on the left and in 5CM separated from the left edge plus a black reference line, otherwise the drawing may be printed in the leftmost there 5CM width is not illuminated dry. So, before printing software to print the file to import, in addition to the need to carry out some simple image processing. The following image processing with Adobe Photoshop CS6-color image processing software as an example (Figure relief and white figure also need such treatment). 1 Open Adobe Photoshop CS6, open the image file you want to print 3 Modify the canvas, select the menu bar of the "image", open the "Canvas Size" dialog box will be relatively tick, enter the width of 5 cm behind the unit selected, click the right arrow, and then click OK.

2 select image menu bar, open the image size option, it is recommended to set the image resolution 300DPI more, to get a good print quality.

36

37

Guides As the front of the head has the installation of UV light, so the need to reserve the position lights installed, you need to print the picture on the left and in 5CM separated from the left edge plus a black reference line, otherwise the drawing may be printed in the leftmost there 5CM width is not illuminated dry. So, before printing software to print the file to import, in addition to the need to carry out some simple image processing. The following image processing with Adobe Photoshop CS6-color image processing software as an example (Figure relief and white figure also need such treatment). 1 Open Adobe Photoshop CS6, open the image file you want to print 3 Modify the canvas, select the menu bar of the "image", open the "Canvas Size" dialog box will be relatively tick, enter the width of 5 cm behind the unit selected, click the right arrow, and then click OK.

2 select image menu bar, open the image size option, it is recommended to set the image resolution 300DPI more, to get a good print quality.

37

36

Canvas modified after (below)

Marquee area

4 do leftmost reference line, good canvas modifying the leftmost figure from top to bottom with the Marquee tool marquee width is about as high 3MM length picture area size, then right-click and choose Stroke; pop-up dialog , enter a pixel width, color options black, and then click OK.

Marquee Tool Stroke Setting

38

39

Canvas modified after (below)

Marquee area

4 do leftmost reference line, good canvas modifying the leftmost figure from top to bottom with the Marquee tool marquee width is about as high 3MM length picture area size, then right-click and choose Stroke; pop-up dialog , enter a pixel width, color options black, and then click OK.

Marquee Tool Stroke Setting

39

38

5 would do the pictures saved in TIFF format

Reference line drawing good example in Figure

The above is based on Adobe Photoshop CS6 software, for example, such as the use of other processing software, you can refer to this case. For printing a mirror image, the image is mirrored then please do leftm ost reference line.

Description good figure according to ctrl + "+" to see if there is no trace to enlarge edge, if not describe that, please follow the steps again

40

Adobe Photoshop CS6 software to do mirroring example: After opening the image, click on the image, rotate the image, click on the canvas can be flipped horizontally

41

5 would do the pictures saved in TIFF format

Reference line drawing good example in Figure

The above is based on Adobe Photoshop CS6 software, for example, such as the use of other processing software, you can refer to this case. For printing a mirror image, the image is mirrored then please do leftm ost reference line.

Adobe Photoshop CS6 software to do mirroring example:

Description good figure according to ctrl + "+" to see if there is no trace to enlarge edge, if not describe that, please follow the steps again

After opening the image, click on the image, rotate the image, click on the canvas can be flipped horizontally

41

40

2 Set Pictures

Eight printout

Picture location settings

Procedure

Find the print position layout module can accurately set the image width and height from the top left corner. (The default width and height is 0, the unit is CM, in general, using the default settings (width to height 0 0) on it)

1 import pictures Open SpringShine RIP software, import way: select the menu bar "File", click Open, and then select the picture you want to pri nt that import pictures; import way: open directly in the middle of the interface software in the space right click and select Open, you can import pictures. (Software support eps. Jpg.tif.ps.bmp. Formats, we recommend using eps file / tif format before importing pictures, please do "reference line")

Such as setting chart position width 1CM height 2CM, as shown below:

Importing way:

Importing way:

3. Printed matter and nozzle distance adjustment (1) printed matter to be completely flat attached to the platform, to avoid

In the Print dialog box, select the drawing file is opened to import

uneven. (2) to the highest point of the printed matter is controlled by a standard platform to move to t he infrared sensor at the head protection (transparent tape block printed matter in order to avoid the application of infrared sensors can not recognize). (3) from printed material and the nozzle is generally 2 to 3 mm distance, the red light when the sensor down by trimming down 1-3, when infrared light is OK just off.

42

43

2 Set Pictures

Eight printout

Picture location settings

Procedure

Find the print position layout module can accurately set the image width and height from the top left corner. (The default width and height is 0, the unit is CM, in general, using the default settings (width to height 0 0) on it)

1 import pictures Open SpringShine RIP software, import way: select the menu bar "File", click Open, and then select the picture you want to pri nt that import pictures; import way: open directly in the middle of the interface software in the space right click and select Open, you can import pictures. (Software support eps. Jpg.tif.ps.bmp. Formats, we recommend using eps file / tif format before importing pictures, please do "reference line")

Such as setting chart position width 1CM height 2CM, as shown below:

Importing way:

Importing way:

3. Printed matter and nozzle distance adjustment (1) printed matter to be completely flat attached to the platform, to avoid

In the Print dialog box, select the drawing file is opened to import

uneven. (2) to the highest point of the printed matter is controlled by a standard platform to move to t he infrared sensor at the head protection (transparent tape block printed matter in order to avoid the application of infrared sensors can not recognize). (3) from printed material and the nozzle is generally 2 to 3 mm distance, the red light when the sensor down by trimming down 1-3, when infrared light is OK just off.

43

42

8 printout

Opaque and transparent tape affixed to the object side need

In the layout module click the Print icon or press F10, the Print dialog box pops up. In the Print dialog box, white ink printing parameters set to 0, the color ink is 1. Then click Print, the print data will be sent to the printer and start printing. Print Icon

With induction lamp is not lit, whichever happens

Print dialog box settings

5. Printing platform reset After the print object and nozzle distance adjustment finished, press the "Auto" button, the platform will be returned to the starting position of the control panel displays "ready to print", which means that the machine is well prepared for printing on the screen at this time.

6 Open the UV lamp switch Open the UV light switch, otherwise printed ink quit (after printing UV light switch can be turned off)

7 Check SpringShine RIP settings

Print data is being transferred

Press the front SpringShine RIP settings to check each module are set correctly. If not, you need to change it back.

44

45

8 printout

Opaque and transparent tape affixed to the object side need

In the layout module click the Print icon or press F10, the Print dialog box pops up. In the Print dialog box, white ink printing parameters set to 0, the color ink is 1. Then click Print, the print data will be sent to the printer and start printing. Print Icon

With induction lamp is not lit, whichever happens

Print dialog box settings

5. Printing platform reset After the print object and nozzle distance adjustment finished, press the "Auto" button, the platform will be returned to the starting position of the control panel displays "ready to print", which means that the machine is well prepared for printing on the screen at this time.

6 Open the UV lamp switch Open the UV light switch, otherwise printed ink quit (after printing UV light switch can be turned off)

7 Check SpringShine RIP settings

Print data is being transferred

Press the front SpringShine RIP settings to check each module are set correctly. If not, you need to change it back.

45

44

Special Note About printing white ink effect 1 white ink effect must do a white figure, then White will block the white layer effects SpringShine RIP to anti-pieces, other settings unchanged.

2 After printing white ink garment fabric care not to move their board and the board, press the online button, the platform can go back online to print. Otherwise white ink and color i nk printing position is not on.

Care clothing plate fixed on the platform 3 white drawings and color pict ures above settings must be consistent with the position in the software, or white ink and color ink printing location may also not on.

OK good care clothing plate position on the platform after printing, you can use double-sided adhesive on the back of good care ironing boards, and then align the position of the platform frame and a little hand pressure being put about, it can be firmly attached to the platform.

About care ironing boards Asked ironing boards determine the position of the platform Users can make a pl ate-size clothing care wireframes (I asked board size clothing is 41 * 62CM, small board size clothing care is 28 * 38CM), then print it directly on t he platform, attention SpringShine RIP software the print width is centered position, height is 0. After printing out the wireframe based on the location of the platform can determine the location of the prop ironing boards.

46

47

Special Note About printing white ink effect 1 white ink effect must do a white figure, then White will block the white layer effects SpringShine RIP to anti-pieces, other settings unchanged.

2 After printing white ink garment fabric care not to move their board and the board, press the online button, the platform can go back online to print. Otherwise white ink and color i nk printing position is not on.

Care clothing plate fixed on the platform 3 white drawings and color pict ures above settings must be consistent with the position in the software, or white ink and color ink printing location may also not on.

OK good care clothing plate position on the platform after printing, you can use double-sided adhesive on the back of good care ironing boards, and then align the position of the platform frame and a little hand pressure being put about, it can be firmly attached to the platform.

About care ironing boards Asked ironing boards determine the position of the platform Users can make a pl ate-size clothing care wireframes (I asked board size clothing is 41 * 62CM, small board size clothing care is 28 * 38CM), then print it directly on t he platform, attention SpringShine RIP software the print width is centered position, height is 0. After printing out the wireframe based on the location of the platform can determine the location of the prop ironing boards.

47

46

Nine routine maintenance and maintenance machinery

(2) pumping waste ink button: Hold down the waste ink pump button switch, about 15 seconds. (Note: After the software required once smoked ink wash, or it may be printed blending)

Daily Care and Maintenance Cleaning 1. Raster bands Every 3-5 days with a clean cloth moistened with a concentration of 95% alcohol wipe grating belt, make sure the grating with no dust or Dirty.

(3) Manual pumping waste ink: Use the syringe into the waste i nk tube inside the cover, and then pumped about 5ML. (Note: After the software required once smoked ink wash, or it may be printed blending)

2 nozzle maintenance Before turning to work every day, we must first carry out a nozzle check, print a test strip is normal, if normal can work; If you find nozzle clogging,

Manual

should be promptly cleared through.

pumping ink

(1) Software Cleaning: Click the computer-driven "Maintenance" option in the "print head cleaning." Or long press to "wash button" for 3 seconds.

(4) split nozzle cleaning: Please visit our website to watch a video, or a phone call to find out about our services to obtain guidance.

Tips: If the machine is not a long time, as long vacation, it is necessary to protect the work ahead of nozzle: clean the nozzles in the in k, and marked moisturizer, so that we can protect well heads. After the holidays, the first moisturizer with cleaning fluid to clean, and then loaded the ink can be.

48

49

Nine routine maintenance and maintenance machinery

(2) pumping waste ink button: Hold down the waste ink pump button switch, about 15 seconds. (Note: After the software required once smoked ink wash, or it may be printed blending)

Daily Care and Maintenance Cleaning 1. Raster bands Every 3-5 days with a clean cloth moistened with a concentration of 95% alcohol wipe grating belt, make sure the grating with no dust or Dirty.

(3) Manual pumping waste ink: Use the syringe into the waste i nk tube inside the cover, and then pumped about 5ML. (Note: After the software required once smoked ink wash, or it may be printed blending)

2 nozzle maintenance Before turning to work every day, we must first carry out a nozzle check, print a test strip is normal, if normal can work; If you find nozzle clogging,

Manual

should be promptly cleared through.

pumping ink

(1) Software Cleaning: Click the computer-driven "Maintenance" option in the "print head cleaning." Or long press to "wash button" for 3 seconds.

(4) split nozzle cleaning: Please visit our website to watch a video, or a phone call to find out about our services to obtain guidance.

Tips: If the machine is not a long time, as long vacation, it is necessary to protect the work ahead of nozzle: clean the nozzles in the in k, and marked moisturizer, so that we can protect well heads. After the holidays, the first moisturizer with cleaning fluid to clean, and then loaded the ink can be.

49

48

3. Periodic lubrication on Mexican trucks g uides and sliders Each week, check the ink car guides and there is no accumulation of dirt

6 waste ink cleanup Waste ink cartridges and waste ink bottle if necessary to clean out more.

on the slider or dust, if there should be wiped clean with a rag, and then reoil (mineral oil based).

Waste Cartridge Guides

Waste ink bottle

The slider 7 white ink circulation

4 Check the water tank Must check whether the water in the tank flows boot every day. If there is

Every day before work, press the white ink button for one minute or so, so white ink circulation to prevent precipitation of white ink.

no flow, non-normal printing, UV light i n order to avoid overheating the lamp burned out.

5 Ink inspection Regularly check the adequacy of the ink bottle ink, ink is insufficient to avoid disconnection, affecting print quality. 50

51

3. Periodic lubrication on Mexican trucks g uides and sliders Each week, check the ink car guides and there is no accumulation of dirt

6 waste ink cleanup Waste ink cartridges and waste ink bottle if necessary to clean out more.

on the slider or dust, if there should be wiped clean with a rag, and then reoil (mineral oil based).

Waste Cartridge

Waste ink bottle

The slider

Guides

7 white ink circulation 4 Check the water tank

Every day before work, press the white ink button for one minute or so,

Must check whether the water in the tank flows boot every day. If there is

so white ink circulation to prevent precipitation of white ink.

no flow, non-normal printing, UV light i n order to avoid overheating the lamp burned out.

5 Ink inspection Regularly check the adequacy of the ink bottle ink, ink is insufficient to avoid disconnection, affecting print quality. 51

50

Ten Troubleshooting

2 When printer, dislocation lights, the computer prompts "Media exhausted or not installed correctly", or "jam."

Common mistakes include: dislocation, no ink, waste ink full, routine errors, ink quit, blur, color cast, not printed.

1 when the printer is printing out of ink lights, the computer prompts "Ink Out" or "ink cartridge can not be recognized." As shown: (1) Cause: Tablet will not move to the initial position to start printing. Solution: Move the innermost flat, then press the "reset" button. (2) Failure Cause: Dirty Mexican trucks guides Solution: Clean the guide rod, and add oil.

(1) Cause: The ink has run out of chips ink value. (Ink Out) Solution: Refresh ink chip value (short press "cleansing" button until the ink out of the car and wait for 3 seconds, then press "cleansing" button.) (2) Failure: or ink chi p damage. (Cartridges can not be identified) Solution: Replace the appropriate ink chip. Replacement method is as follows: Turn off the machine's power, open the back cover, find the corresponding ink chip replaced.

(3) When the printer to print, dislocation and lack of ink lamp lights alternately, slow flashing, the computer prompts the "Service Request: Printer parts are approaching the deadline."

Cause: Record on the motherboard where the value of the waste ink is full. Solution: Discard the waste ink waste ink bottle with a random cleared software to initialize the v alue of the waste ink. Cleared as f ollows: Opened the first machine (if the error is not hell), data cable to connect the machine to a computer, and then use the software to be cleared is cleared.

Open the back cover 52

Replace the corresponding chip 53

Ten Troubleshooting

2 When printer, dislocation lights, the computer prompts "Media exhausted or not installed correctly", or "jam."

Common mistakes include: dislocation, no ink, waste ink full, routine errors, ink quit, blur, color cast, not printed.

1 when the printer is printing out of ink lights, the computer prompts "Ink Out" or "ink cartridge can not be recognized." As shown: (1) Cause: Tablet will not move to the initial position to start printing. Solution: Move the innermost flat, then press the "reset" button. (2) Failure Cause: Dirty Mexican trucks guides Solution: Clean the guide rod, and add oil.

(1) Cause: The ink has run out of chips ink value. (Ink Out) Solution: Refresh ink chip value (short press "cleansing" button until the ink out of the car and wait for 3 seconds, then press "cleansing" button.) (2) Failure: or ink chi p damage. (Cartridges can not be identified) Solution: Replace the appropriate ink chip. Replacement method is as follows: Turn off the machine's power, open the back cover, find the corresponding ink chip replaced.

(3) When the printer to print, dislocation and lack of ink lamp lights alternately, slow flashing, the computer prompts the "Service Request: Printer parts are approaching the deadline."

Cause: Record on the motherboard where the value of the waste ink is full. Solution: Discard the waste ink waste ink bottle with a random cleared software to initialize the v alue of the waste ink. Cleared as f ollows: Opened the first machine (if the error is not hell), data cable to connect the machine to a computer, and then use the software to be cleared is cleared.

Open the back cover

Replace the corresponding chip 53

52

The CD-ROM supplied in the R1800 maintenance software copied onto your computer, or download the software f rom R1800 repair our website to your computer. Then turn off anti-virus software, open the R1800 Maintenance Software

The next dialog box, select "Waste ink pad counter" and click "OK".

Double-click to open

After the dialog box opens, click Particular adjustment mode Dialog box pops up again, turn hit Read, and then click Initialization finally click Finish. Cleared complete, turn off the machine, reboot that is good.

Then select the corresponding USB port

54

55

The CD-ROM supplied in the R1800 maintenance software copied onto your computer, or download the software f rom R1800 repair our website to your computer. Then turn off anti-virus software, open the R1800 Maintenance Software

The next dialog box, select "Waste ink pad counter" and click "OK".

Double-click to open

After the dialog box opens, click Particular adjustment mode Dialog box pops up again, turn hit Read, and then click Initialization finally click Finish. Cleared complete, turn off the machine, reboot that is good.

Then select the corresponding USB port

55

54

4 When the printer t o print, dislocation and lack of ink lamp lights while rapid blinking, the computer prompts "General Error."

7 items printed color cast. (1) Failure Cause: out of ink or disconnected. Solution: Well, then print a nozzle check. (2) Cause: ICC curve unselected right. Solution: Select the correct ICC profile. (3) Failure Cause: The computer virus. Solution: Disconnect the network cable, antivirus, reinstall the driver and the RIP software.

Reasons (1) failure: print data errors. Solution: Delete the print job, restart the printer. (2) failure reasons: foreign body blocking Mexican trucks to move. Solution: remove foreign bodies, delete the print job, restart the printer. (3) Failure Cause: Mexican car too much resistance, raster dirty. Solution: do routine maintenance, Carriage guides, guided slide lubricating, use alcohol to clean the grating belt.

8 The machine does not print (1) Cause: The data cable is not connected. Workaround: Connect the data cable before printing. (2) Cause: SpringShine RIP is not set correctly. Solution: Check SpringShine RIP settings are correct. (3) Failure reason: to stop a print job before halfway, did not cancel the print job. Workaround: Cancel the print job before printing. (Cancel the print job: Double-click the drive icon will pop up a list of print, and then file, so the task can be canceled)

Right side 5. Printed printed matter about 5CM ink has quit. (1) Cause: Figure 5CM do not add the reference line. Solution: Before printing has been done to confirm the reference line.

6. Printed items is v ery vague. Reasons (1) failure: printed matter the distance between the nozzle is too high. Solution: Before printing the print nozzles confirm good distance between objects. (2) Failure Cause: The picture is not clear enough for printing Solution: Print high-definition map.

56

57

4 When the printer t o print, dislocation and lack of ink lamp lights while rapid blinking, the computer prompts "General Error."

7 items printed color cast. (1) Failure Cause: out of ink or disconnected. Solution: Well, then print a nozzle check. (2) Cause: ICC curve unselected right. Solution: Select the correct ICC profile. (3) Failure Cause: The computer virus. Solution: Disconnect the network cable, antivirus, reinstall the driver and the RIP software.

Reasons (1) failure: print data errors. Solution: Delete the print job, restart the printer. (2) failure reasons: foreign body blocking Mexican trucks to move. Solution: remove foreign bodies, delete the print job, restart the printer. (3) Failure Cause: Mexican car too much resistance, raster dirty. Solution: do routine maintenance, Carriage guides, guided slide lubricating, use alcohol to clean the grating belt.

8 The machine does not print (1) Cause: The data cable is not connected. Workaround: Connect the data cable before printing. (2) Cause: SpringShine RIP is not set correctly. Solution: Check SpringShine RIP settings are correct. (3) Failure reason: to stop a print job before halfway, did not cancel the print job. Workaround: Cancel the print job before printing. (Cancel the print job: Double-click the drive icon will pop up a list of print, and then file, so the task can be canceled)

Right side 5. Printed printed matter about 5CM ink has quit. (1) Cause: Figure 5CM do not add the reference line. Solution: Before printing has been done to confirm the reference line.

6. Printed items is v ery vague. Reasons (1) failure: printed matter the distance between the nozzle is too high. Solution: Before printing the print nozzles confirm good distance between objects. (2) Failure Cause: The picture is not clear enough for printing Solution: Print high-definition map.

57

56

Eleven machine transport considerations * Do not upside down or tilted transport * Do not lift platform parts * Keep the ink out before transport to avoid ink leakage accidentally during transport * Please ink tube wrapped in bags, place the ink leaks (if necessary To Ink ink empty) * Mexican trucks must be in the original location, and can not be removed manually * Two or more of lifting machines

58

Eleven machine transport considerations * Do not upside down or tilted transport * Do not lift platform parts * Keep the ink out before transport to avoid ink leakage accidentally during transport * Please ink tube wrapped in bags, place the ink leaks (if necessary To Ink ink empty) * Mexican trucks must be in the original location, and can not be removed manually * Two or more of lifting machines

58

A3 UV Printer Manual.pdf

Recommend Documents