Part No. 8G8528 15 April 09
KODAK Medical X-ray Processor 2000 Model 212 / 220-240V, 50 Hz Model 213 / 220-240V, 60 Hz Service Manual
Contents To Order Parts or for Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Through-the-wall-mounting film infeed - Machine in light room . . . . . . . . . . . . . . . . . . . . . . 4 Existing wall breakthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Through-the-wall-mounting film output - Film output to the light room . . . . . . . . . . . . . . . . . 5 Film exit through the wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Dryer rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Machine cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Algae . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Excessive algae growth in water tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 The mains switch is “on,” but there is no function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 No display, but the circulation pumps are running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Machine does not start automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Machine does not stop automatically; the motor and fan run continuously . . . . . . . . . . . 7 The drive motor does not run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The display shows error message “E2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Baths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 No circulation in the developer or fixer baths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The developer bath temperature is not reached . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The developer bath temperature is higher than the set temperature, the display shows two crossbars, the developer temperature button blinks . . . . . . . . . . . . . . . . . . . 8 The developer bath temperature too high or too low (display shows values of 20 °C or 42 °C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The calibration of the bath temperature / actual bath temperature is different from the displayed value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Calibration process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Film defects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Films will not dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The film does not transport correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Scratches, pressure marks, dirt on the film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Replenishment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The replenishment pump does not work or works insufficiently . . . . . . . . . . . . . . . . . . . . 9 Dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The display shows error message “E4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The dryer ventilation does not function, no water inflow when water cock opened . . . . . 9 The dryer ventilation is too weak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The dryer temperature cannot be reached . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The dryer temperature display exceeds the set value . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Dryer temperature cannot be reached or is too high (display shows values approximately 30 °C and 75 °C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
i
Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rinsing water does not flow, ventilation runs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water tank overflows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wires and cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard roller racks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
10 10 10 11 12 15 18
The information contained herein is based on the experience and knowledge relating to the subject matter gained by Carestream Health, Inc. prior to publication. No patent license is granted by this information. Carestream Health, Inc. reserves the right to change this information without notice, and makes no warranty, express or implied, with respect to this information. Carestream Health shall not be liable for any loss or damage, including consequential or special damages, resulting from any use of this information, even if loss or damage is caused by Carestream Health’s negligence or other fault.
1
To Order Parts or for Technical Support To Order Parts or for Technical Support Type
Number
Phone
+49 7062 9255 0
Direct Mail
PROTEC® GmbH & Co. KG Lichtenberger Strasse 35 D-71720 Oberstenfeld Germany
E-Mail
2
[email protected]
Hours Normal Business Hours: Central European Time (Berlin, Paris, Rome) Monday - Thursday: 8 am to 5 pm Friday: 8 to 12 am (noon)
Dimensions Dimensions Depending on the model type, the MXP-2000 has either an open stand or a closed cabinet.
Transport
To carry hold here!
To carry hold
3
4 Working space
Dimensions in cm
Wall breakthrough for film input
Through-the-wall mounting set 1280 0 0000
Installation Data
Installation Data
Through-the-wall-mounting film infeed - Machine in light room
Working space Door width min. 69
Film exit height
Dimensions in cm
Wall breakthrough for film exit
Through-the-wall mounting set 1281 0 0000
Installation Data Through-the-wall-mounting film output - Film output to the light room
5
Installation Data 1
Mains 220 - 240 V, 16 A; Cu wire-Kabel 3 x 1.5 mm2; Ground-Leakage-Switch 25 A / 30 mA; power consumption 2.2 kW.
2a Power switch 16 A; 140 cm above floor. 2b Machine connection: Socket incl. earth 60 cm above floor. 3a Water connection: Water consumption 1.9 L/min; water temperature may not be below 5 °C. 3b Water stopcock 3/4 in. washing machine connection. 4
Ventilation of darkroom is necessary.
5
Drainage hose, diameter 50 mm, acid resistant; odor preventor with connection for 10 mm hose.
6
Drainage for developer; hose connection 10 mm. Suitable collection bins must be provided. Local water board regulations have to be complied with.
7
Drainage for fixer; hose connection 10 mm. Suitable collection bins must be provided. Local water board regulations have to be complied with.
8
Sink with hot/cold water and a flexible hose; inner dimensions: 60x40x30 cm deep; material: ceramics, stainless steel, plastic.
9
The replenishment containers can be placed under the processor or can be installed externally.
10 Wall breakthrough for film exit through the wall infeed (page 4): The processor is installed outside the darkroom; the film exits into a light room. For the “through-the-wall mounting infeed” alteration, assembly kit no. 1280-0-0000 is necessary. 11
Wall breakthrough for film exit through the wall output (page 5): The processor is installed inside the darkroom; the film exits through the wall to a light room. For the “through-the-wall mounting film output” alteration, assembly kit no. 1281-0-0000 is necessary.
Film exit through the wall On machines that have the film exit through the wall into a light room, the following modifications have to be made: Dryer rack 1 Remove the two rollers from position A. To do this, open the bolt from spring at position 1 and remove the gear from the lower roller. 2 Move the curved guide bar from position C to position D. To do this, open bolts 3 and 4. 3 Reinstall the pair of rollers in position B. Mount the spring at position 2. Machine cover The front film exit opening in the machine cover has to be closed with the screen contained in the assembly kit. For the “through-the-wall mounting film output” alteration, assembly kit no. 1281-0-0000 is necessary.
6
Troubleshooting Troubleshooting 1
Algae
1.1 Excessive algae growth in water tank Algae growth inside the water tank is not only annoying, it causes increased cleaning work and leaves residue on the films. When algae growth increases, countermeasures are necessary: •
When work has been completed at the end of the day, drain the water out of the machine.
•
Clean the dryer water rack regularly. Use a soft sponge and soap to remove residue from the rollers.
•
Install a particle filter system in the fresh water supply for the processor.
•
If no other solutions can be found, then the use of anti-algae-agents can be a great improvement (automatic dispensers work the best). However, cleaning agents containing chlorine may corrode the rubber rollers and highgrade steel in the tank area (check before use).
2
General
2.1 The mains switch is “on,” but there is no function • Ensure that the electrical socket has a power supply. •
Check the machine fuses. Use only the original manufacturer’s replacement fuses. These fuses are optimized for use under existing conditions.
•
While the power switch is on, check the following component: Voltage on contact of main switch. If there is no voltage, replace the respective component.
2.2 No display, but the circulation pumps are running • Check the entry current of 5 V on contacts no. 7 and 8 of 8-pole-plug X23 from the control unit's PCB. If voltage is present, then replace the control unit. •
Check fuse (5 A) on the power PCB.
•
Disconnect the temperature sensor developer bath (X25) and check the display again.
•
Disconnect the temperature sensor dryer (X24) and check the display again.
3
Drive
3.1 Machine does not start automatically • When the machine is switched on, place a film in the infeed until it reaches the pull-in rollers. If necessary, move the film sideways to activate the light barrier. If the display shows two bars with decimal points, then the light barrier is in order. Check each of the four eyes on the light barrier. Each eye must start the machine. If they do not, then replace the light barrier. Check the connection of the light barrier. If there is no reaction on the display, then replace the light barrier. Eventually the control unit has be changed. •
The display shows “E1”: The cover switch is not actuated by the latch on the cover. The cover switch has no current passage when activated. Replace the cover switch.
•
The developer temperature button is flashing: see “The developer bath temperature is not reached” on page 8.
3.2 Machine does not stop automatically; the motor and fan run continuously • The display is flashing: Control is in the manual mode. Switch back to automatic mode (see the Operator Manual). •
The display continuously shows two bars with decimal points: The light sensors on the light barrier are dirty or the light barrier is defective. Clean with a soft cloth. If necessary, remove the light barrier to clean it. If the switches are defective, the machine can still be used in the manual mode (see the Operator Manual).
•
The PCB is possibly faulty. Replace it.
7
Troubleshooting 3.3 The drive motor does not run • The display shows “E1” or “E3”: See the Operator Manual for descriptions of the error messages. •
If current can be registered on the motor, then the motor is defective. Replace it.
•
The dryer fan runs, but there is no voltage on the motor: Replace the power PCB.
3.4 The display shows error message “E2” • Check the plug-ins between the main drive motor and the power PCB. If “E2” appears again, then replace the main drive motor. In rare cases, the PCB causes the error. See the Operator Manual for descriptions of the error messages.
4
Baths
4.1 No circulation in the developer or fixer baths • The circulation pump runs but no circulation can be registered. There is an air lock in the heating and circulation system. Ventilate the system (see the Operator Manual). •
There are particles in the pump chamber. Drain the bath before opening the pump. The pump chamber can be easily opened by removing the four screws. After cleaning, close the pump chamber and ensure that the seal is correctly reinserted and not damaged.
•
The pump does not run. Check the voltage on the connections X3 and X4 of the power PCB. If no voltage can be registered, see “The mains switch is “on,” but there is no function” on page 7. If voltage can be registered, replace the pump.
4.2 The developer bath temperature is not reached •
No circulation: 1) The circulation pump has no current or is defective. 2) There is air in the circulation system.
•
Check the temperature safety switch on the heat-exchanger. For temperatures up to 90 °C, the temperature limiter must have current passage.
•
Check the heating element: Current flow resistance should read approximately 66 Ω.
•
Check the temperature sensor: Voltage at X25 on the control unit between pin 3 (green) and pin 2 (brown). The value should read 0.32 V at a temperature of 32 °C.
•
Increase the temperature and check the current on the control unit of clip X13. The voltage should be between the mains and 60 Volts. If it does not, then replace the electronics.
4.3 The developer bath temperature is higher than the set temperature, the display shows two crossbars, the developer temperature button blinks • See above •
Check the current on power PCB at clip X13. There may be no current. If current is registered, replace the electronics.
4.4 The developer bath temperature too high or too low (display shows values of 20 °C or 42 °C) • Check the temperature sensor. The sensor is either not connected or defective. 4.5 The calibration of the bath temperature / actual bath temperature is different from the displayed value • The differences between the displayed temperature and the measured value in the developer bath can be adjusted. An adjustment may be necessary; for example, after replacing the bath temperature sensor. A calibration has to be done if the difference is higher than +/- 0.5 °C. The adjustment range is +/- 2 °C.
8
Troubleshooting Calibration process 1. Switch the processor off. While pressing the developer temperature button, switch the processor on. The display will show the developer bath temperature as measured by the sensor. 2.
Measure the actual temperature inside the developer bath using a calibrated thermometer.
3.
At first, adjust the displayed value in 1 degree increments using the arrow buttons. To adjust the decimal, hold developer temperature button down and press the up or down arrow button.
4.
Switch the machine off again.
5
Film defects
5.1 Films will not dry • Hot air comes out of the air channel, but the film is still not dried to satisfaction. Check the chemicals and film type. If this leads to no solution, then the transport speed of the machine can be reduced (see the Operator Manual). 5.2 The film does not transport correctly • Check the positioning of the roller racks and ensure that the levers are closed. Check the gears on the roller racks. Check the positioning of the guide bars and the roller pressure. •
Check the gears on the motor and worm gear of the drive shaft.
5.3 Scratches, pressure marks, dirt on the film • Straight scratches in the infeed direction suggest a fault on the guide bars. Check the roller racks individually and adjust the guide bars. If the guide bars are damaged, replace them. •
Pressure marks are caused by contaminated or damaged rollers. If necessary, replace the rollers.
6
Replenishment
6.1 The replenishment pump does not work or works insufficiently •
Clean the valves inside the connection tube of the pump. Install the valve-insert correctly. Pay attention to the flowthrough direction!
•
The replenishment pump sucks air in. Check the hoses and connections.
•
Check the eccentric position. The capacity is approximately 710 ml/min (850 ml/min with 60 Hz power mains) at setting to 100%. The minimum setting must not be below 50%.
•
Activate replenishment (in manual mode) and while on, check the voltage of connection X6 (DEV) and X7 (FIX) on the power PCB. If no voltage can be registered, replace the power PCB.
7
Dryer
7.1 The display shows error message “E4” The following parts should be checked and if faulty be replaced: •
Power PCB (in standby, no voltage at X12)
•
Temperature sensor (see “The dryer temperature display exceeds the set value” on page 10)
•
Dryer fan (see “The dryer ventilation does not function, no water inflow when water cock opened” on page 9 and see “The dryer ventilation is too weak” on page 10)
•
Dryer heating element
7.2 The dryer ventilation does not function, no water inflow when water cock opened • Start the machine in manual mode (see the Operator Manual). Check the current on X9 and X10 connections on the power PCB. If no voltage can be registered, replace the power PCB. Otherwise, the ventilation has been connected wrong or is defective.
9
Troubleshooting 7.3 The dryer ventilation is too weak • If the ventilation is connected incorrectly, it runs very slowly (the heating element in the air channel starts to glow). Dryer ventilation connection: X9
L
black
X9
Z
brown
X10
N
blue
X10
PE
yellow / green
7.4 The dryer temperature cannot be reached • Check the temperature sensor: Measure the voltage at X24 on the power PCB between pin 3 (green) and pin 2 (brown). The value should read 0.32 V at a temperature of 32 °C. •
Only cold air flows from the air channel: The heating element in the air channel is defective. Disconnect the X12 clip on the power PCB and measure the resistance of the heating element (approximately 26 Ω).
•
Enter a dryer temperature of 70 °C. Check the voltage of X12 on the power PCB. If no voltage can be registered, replace the control unit.
•
Verify the input voltage of 220 - 240 VAC with the heater actuated.
7.5 The dryer temperature display exceeds the set value • Check the temperature sensor: Measure the voltage at X24 on the power PCB between pin 3 (green) and pin 2 (brown). The value should read 0.32 V at a temperature of 32 °C. •
Enter a dryer temperature of 35 °C. Check the voltage of X12 on the power PCB. If no voltage can be registered, replace the control unit.
7.6 Dryer temperature cannot be reached or is too high (display shows values approximately 30 °C and 75 °C) • Check the temperature sensor. The sensor is either not connected or is defective.
8
Water
8.1 Rinsing water does not flow, ventilation runs • The water pressure in the water system is too low: The minimum pressure is 2 bar (29 psi). •
The valve activates, but there is no flow passage: The filter at the inflow is blocked.
•
Check the solenoid valve.
8.2 Water tank overflows • The water drainage hose (overflow) should have a constant fall. The hose end should be positioned above the drainage level in the syphon. •
Check the water drainage in the tank and hose for blockage and contamination.
•
When extreme algae growth is noticed, the overflow can be connected directly at the back of the water tank.
10
Spare Parts Spare Parts
Position
Order No.
Description
1 1190-0-0200 Machine cover 2 1190-0-3101 Light protection cover 3 1190-0-0105 Film infeed tray 4 1191-0-0105 *Film infeed tray, graphics art 5 2006-0-0005 Drain stopcock 10 mm 6 1101-0-2000 Replenisher tank dev. 25l 7 1101-0-2100 Replenisher tank fix. 25l 8 1101-0-1700 Suction pipe w. filter f. 25 l tank 9 1101-0-4100 Floating cover developer 10 2018-0-0001 Water inlet tube 11 1196-0-0010 Processor base stand (open) 12 1190-0-1201 Control panel foil 2018-0-0005 Tube 4x1mm, green 2018-0-0021 Tube 9x2mm, red clear 2018-0-0022 Tube 9x2mm, blue clear 2018-0-0007 Tube 16x4mm, clear, reinforced 2018-0-0008 Tube 10x2mm, red, reinforced 2018-0-0009 Tube 10x2mm, blue, reinforced 2018-0-0012 Tube 10x2mm, clear, reinforced 2022-0-0014 Tube clamp Snap 2022-0-0019 Wire tube clamp 2022-0-0026 Wire tube clamp 2022-0-0028 Wire tube clamp 2022-0-0030 Wire tube clamp 2022-0-0005 Wire tube clamp 1101-0-4600 Floating balls, 300 pcs. 1101-0-4800 Floating balls, 200 pcs. *Parts for graphic arts version only.
11
Spare Parts Wires and cables Position
Order No.
-
1190-0-0108 1190-0-0112 1190-0-0110 1190-0-0111 1190-0-0114 2004-0-0010 2004-0-0016 2004-0-0012
12
Description Transformer > power PCB 20V Power PCB > transformer 230V UL Power PCB > controller PCB Motor > controller PCB Fuse holder > controller PCB UL Electrical power lead Electrical power lead UL Main switch > fuse holder UL
Spare Parts
Installation position see page 9
Position
Order No.
20 21 22
2002-1-0011 2036-1-0001 0002-1-0001 0002-2-0001 0002-1-0008 0190-0-0900 2008-5-0006 0190-0-1801 1190-0-1802 2001-9-0006 1190-0-1102 1190-0-1503 1170-0-1502 1170-0-1503 0170-0-2400 0170-4-2400 2007-0-0010 1190-0-0902 0196-0-0900 2028-0-0023 2010-0-0004 2010-0-0010 2027-0-0012 0190-0-2700 1190-0-0117 1190-0-0904
23 24 25 26 27 30 31 32 33 34 36 37 38 40 41 42 43 44 45
Description Circulation pump MD-10 (circulation) Safety-transformer UL Bellows pump KB2X 230V, 50Hz Bellows pump KB2X 230V, 60Hz Valve insertion f. pos. 22 Power PCB Axial fan Fan plate Light protection plate Main drive motor, new Motor bracket, variation 2 Drive shaft, variation 2 Bearing block Worm-gear Micro switch (Cover) Micro switch (Cover) UL Operator for micro switch Bracket for cover switch, variation 2 Controller PCB Power switch Fuse holder Fuse slow blow in gold, T 10A/250V Traction relief Traction relief for UL power cord Coupling Line filter
13
Spare Parts
Position
Order No.
50
2008-5-0007 2008-7-0007 1190-0-1301 0190-0-1300 0190-7-1300 0190-0-2200 1190-0-1302 2003-5-0002 2003-7-0002 1190-0-2101 2005-0-0005 1190-0-4100 1190-0-0103 2030-0-0014 0190-0-0800 1190-0-0107 1120-5-1900 1190-0-1304
51 52 53 54 55 56 57 59 60 61 62-63 64 65 66
14
Description Ventilation 230 V (dryer) Ventilation 230 V (dryer) UL Air channel Heating element 2kW/230V (dryer) Heating element 2kW/230V (dryer) UL Temperature sensor (same for bath and dryer heating) Plate for air channel Heating element (bath heating) Heating element 800 W UL Heat exchanger Temperature limiter Condensation cover E Light barrier support Rubber inlet Light barrier holder compl. Light barrier casing Solenoid valve 230 V Channel dryer heating
Spare Parts Standard roller racks
15
Spare Parts
Position
Order No.
69 69a 70 70a 72 72a 73 74 75 77a 77b 77c 77d 77e 79 80 81 82 83 84 85 86 86a 87 88 90 91 92 93 93a 94 95 95a
1190-0-0300 1196-0-0400 1190-0-0600 1190-0-0610 1190-0-0620 1191-0-0300 1191-0-0400 1191-0-0600 1191-0-0610 1191-0-0620 1190-0-0301 0190-0-0301 1190-0-0401 0190-0-0401 1101-0-3700 1101-0-4500 1190-0-3600 1101-0-0306 1101-0-0307 1190-0-0302 1170-0-0304 1170-0-0303 1101-0-0315 1190-0-0303 1190-0-0310 1101-0-0316 1101-0-0311 1101-0-0303 1101-0-0304 1170-0-0302 1101-0-0302 1101-0-0305 1101-0-0317 1102-0-0401 2014-0-0001 1190-0-0604 1190-0-0603 1190-0-0605 1190-0-0609 0190-0-0608 1190-0-0607 1190-0-0606 0190-0-0606
16
Description Developer standard Fixer Water/dryer standard Dryer C2 Water C2 Developer graphics art Fixer graphics art Water/dryer graphics art Dryer graphics art C2 Water graphics art C2 Side plate dev. right Side plate dev. left w. shafts Side plate fix. right Side plate fix. left w. shafts Guide bar 2, curved with nose Guide bar 2, curved with nose Guide bar straight, short PU-roller ground Rubber roller Flat spring 68 Flat spring 55 Flat spring 36 Flat spring 30 Flat spring 26 Drive shaft rack C 2 Shaft Distance bar Gear t = 32, D-hole Gear t = 32, R-hole Worm wheel Gear t = 16, D-hole Bearing bush, white Bearing bush, black Bearing w. clearance Circlip Dryer plate, small Dryer plate, large Dryer plate, rear Side plate D top right Side plate D top left (with shafts) Slide for dryer separation Side plate W/D bottom right Side plate W/D bottom left (with shafts)
Spare Parts
Position
Order No.
100-104 100 101 102 103 104
1281-0-0000 0281-0-0201 0281-0-0100 1253-0-0001 0281-0-0202 0281-0-0204 0281-0-0203
Position
Order No.
110-115 110 111 112 113 114
1280-0-0000 0280-0-0102 0280-0-0103 0280-0-0104 0280-0-0105 0280-0-0202
Description: Mounting set “Through-the-wall-mounting set film output” Wall plate Sealing wedge Catch basket Mounting kit Strap Blind plate 2
Description: Mounting set “Through-the-wall-mounting set film feed” Light protection Light protection, left Light protection, right Wall plate small Mounting kit
17
Electrical Diagrams
Schaltplan/Current flow chart MXP-2000
Electrical Diagrams
18
MXP-2000
Leistungsteil/power element
Electrical Diagrams
19
MXP-2000
Netzteil/power supply
Electrical Diagrams
20
MXP-2000
Anschlüsse/connections
Electrical Diagrams
21
MXP-2000
CPU
Electrical Diagrams
22
MXP-2000
Messchaltung/test circuit
Electrical Diagrams
Important: For machine type COMPACT 2 Jumper no. X7 should be placed in pos. 2-3.
23
MXP-2000
Heizung/heating
Electrical Diagrams
24
Electrical Diagrams
25
The Kodak trademark and trade dress are used under license from Kodak.
© Carestream Health, Inc. 2009
Carestream Health, Inc. 150 Verona Street Rochester, NY 14608 8G8528
