3FQ-24068-43XU-PGZZA-07-RPEC Fixed Access 7302-7330-7360 ISAM R4_3_X Software Upgrade MOP.doc

7302 ISAM/ISAM-V 7330 ISAM FTTN 7360 ISAM FX R4.3.X SOFTWARE UPGRADE MOP

Authors: Taner USTEBAY, Gucer BAYAT Alcatel-Lucent

GPEC (Global Product Expertise Center) WLEN – Fixed Access Team

3FQ 24068 43XU PGZZA

7302 ISAM/ISAM-V, 7330 ISAM FTTN, 7360 ISAM FX R4.3.X Software Upgrade MoP

Page 2 of 47

TABLE OF CONTENTS 1.

INTRODUCTION............................................................................................... 3 1.1. 1.2. 1.3. 1.4. 1.5. 1.6. 1.7. 1.8.

2.

SITE VISIT PREPARATION..................................................................................12 2.1. 2.2. 2.3. 2.4. 2.5. 2.6.

3.

UPGRADE CHECKLIST......................................................................................30 UPLOAD NEW SOFTWARE RELEASE TO THE AMS SERVER....................................................30 PREPARING THE SOFTWARE FOR UPGRADE..................................................................32 DOWNLOADING NEW SOFTWARE TO AN NE.................................................................34 ACTIVATING THE NEW SOFTWARE VIA TL1.................................................................35

SOFTWARE UPGRADE VIA CLI............................................................................36 6.1. 6.2. 6.3. 6.4.

7.

UPGRADE CHECKLIST......................................................................................19 UPLOAD THE DOWNLOADED SOFTWARE RELEASE TO THE AMS SERVER.....................................19 PREPARING THE SOFTWARE FOR UPGRADE..................................................................20 ADDING NEW SOFTWARE RELEASE TO 5520 AMS..........................................................22 DOWNLOADING NEW SOFTWARE TO AN NE.................................................................24 ACTIVATING THE NEW SOFTWARE VIA AMS.................................................................27

SOFTWARE UPGRADE VIA TL1............................................................................30 5.1. 5.2. 5.3. 5.4. 5.5.

6.

PRE-UPGRADE CHECKLIST.................................................................................16 GETTING THE SOFTWARE..................................................................................16

SOFTWARE UPGRADE VIA AMS...........................................................................19 4.1. 4.2. 4.3. 4.4. 4.5. 4.6.

5.

INFORMATION CHECKLIST..................................................................................12 TOOLS AND DEVICES.......................................................................................12 PERSONNEL IN CHARGE....................................................................................13 ESCALATION PROCEDURE...................................................................................13 BOX CONFIGURATIONS.....................................................................................14 TIMETABLE................................................................................................. 15

PRE-UPGRADE TASKS......................................................................................16 3.1. 3.2.

4.

HOW TO USE THIS DOCUMENT..............................................................................3 SCOPE OF THIS DOCUMENT.................................................................................3 DOCUMENT REVISION HISTORY..............................................................................3 FEEDBACK................................................................................................... 3 GLOBAL PRODUCT EXPERTISE CENTER WLEN – FIXED ACCESS TEAM HOMEPAGE.............................4 7302 ISAM/ISAM-V, 7330 ISAM FTTN, 7360 ISAM FX DOCUMENTS AT GPEC SITE....................4 SUPPORTED HARDWARE LIST FOR RELEASE 4.3.X...........................................................5 5520 AMS - ISAM COMPATIBILITY.........................................................................11

UPGRADE CHECKLIST......................................................................................36 PREPARING THE SOFTWARE FOR UPGRADE..................................................................36 DOWNLOADING NEW SOFTWARE TO AN NE.................................................................37 ACTIVATING THE NEW SOFTWARE VIA CLI..................................................................40

POST-SOFTWARE UPGRADE CHECKLIST................................................................41

APPENDIX A.

INDEX OF TABLES............................................................................42

APPENDIX B.

INDEX OF FIGURES...........................................................................43

APPENDIX C.

REFERENCES..................................................................................44

APPENDIX D.

GLOSSARY.....................................................................................45

Internal Note: Do not manually change “Table of Contents” field. Update field for any changes by right clicking on field and selecting “Update Field” tab.

Copyright @ Alcatel-Lucent GPEC TEAM



Page 3 of 47

1. INTRODUCTION 1.1. How to Use This Document Internal Note: This document was prepared for internal use. For a project version of this document, local units are responsible for deleting all “GPEC, ALU” internal references (names, engineer names, links etc.) and converting the document to PDF format. Red highlighted text should be removed before delivering this document. Yellow highlighted text should be updated before delivering this document.

1.2. Scope of This Document This document was prepared by ALU GPEC Fixed Access Team. The objective is to provide detailed information of upgrade for 7302 ISAM/ISAM-V FD, 7330 ISAM FTTN, 7360 ISAM FX R4.3.X release at the customer premises. The document gives all the information needed for preparation and upgrade of ISAM software.

1.3. Document Revision History Date

Version

Author

Change

13.05.2011

1.0

Taner USTEBAY, Ilker ALBAYRAK

Document Creation

14.08.2011

1.1

Gucer BAYAT, Mehmet SOZBILIR

Document Update

15.08.2011

1.2

Gucer BAYAT

“SW Upgrade via TL1 section” is added.

28.12.2011

1.3

Mehmet SÖZBİLİR

R4.3.02 Update

18.03.2012

1.4

Taner USTEBAY

Updating GPEC related information

Table 1 : Document Revision History

1.4. Feedback For any feedback on this document, please contact to mail list; GPEC Fixed Access mail list




Page 4 of 47

1.5. Global Product Expertise Center WLEN – Fixed Access Team Homepage Internal Note: Please check GPEC-Fixed Access Homepage for the most recent version of this document. Home Page: https://all1.na.alcatel-lucent.com/teams/GPECIPDWA/default.aspx Subscription Link: http://list.web.alcatel-lucent.com/cgi-bin/wa?SUBED1=GPECfixedaccess-news&A=1

1.6. 7302 ISAM/ISAM-V, 7330 ISAM FTTN, 7360 ISAM FX Documents at GPEC Site No

Document Name

1

Hardware Installation MoP

2

Software Installation & Field Integration MoP

3

Acceptance Test Procedure

4

Software Upgrade MoP

5

Software Migration MoP

6

Backup and Restore Procedure

7

Password Recovery Procedure

8

NE Discovery Procedure Table 2 : Document List




Page 5 of 47

1.7. Supported Hardware List for Release 4.3.X 7302 ISAM R4.3.02 Prefix Number Fu Va Name 3EC 3EC 3EC 3EC 3EC 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE

37028 37028 37028 37533 37533 00139 00139 00140 00140 00161 00161 00162 00162 21591 21709

AA AB AE NB ND AA BA AA BA AA AB AA AB AA AF

3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE

21710 22195 22513 22736 24564 24594 24685 25261 25263 25590 25591 26682 26685 26698 26698 26698 26698 26999 27003 27289 27289 27289 27289 27420 27420 27420 27562 27562 27562 27649 27715 27725 27725

AA AF AB AA AA AA AA AA AA AA AA BA AA AA AB DA DB AA AA AA AB BA BB AA AB AC AA AB AC AA AA AA AF

Mnemonic

ETSI Central Office Splitter - with N+1 redundancy ETSI Central Office Splitter ETSI Central Office Splitter - with full test access ADSL FAN Unit with dust filter ADSL Fan Unit - with dust Filter 48-port VDSL2 over POTS LT Unit vers. C 48-port Shielded VDSL2 over POTS LT Unit vers. C 48-port VDSL2 over ISDN LT Unit vers. D 48-port Shielded VDSL2 over ISDN LT Unit vers. D 48-port VDSL2 over ISDN LT Unit vers.H 48-port VDSL2 over ISDN LT Unit vers.H 48-port VDSL2 over POTS LT Unit vers. G 48-port VDSL2 over POTS LT Unit vers. G ADSL Splitter Subrack MII Passive POTS Splitter - with full test access 48 lines ETSI Passive POTS Splitter - no full test access Passive POTS Splitter - with metallic test access Test Access Unit 48 port Passive ADSL-POTS/ISDN Splitter Passive POTS Splitter ADSL Splitter Subrack Passive POTS Splitter 48 lines Passive ADSL-POTS/ISDN splitter -2B1Q 48 lines Passive ADSL-POTS/ISDN splitter -4B3T 24 lines VDSL Ppassive POTS Splitter 24 lines Passive POTS/ISDN 2B1Q VDSL Splitter MultiDSL LT Unit version B NEP FleXible Shelf version A Combined NT Unit version A Combined NT Unit version A Combined NT Unit version A Combined NT Unit version A SHDSL Cut-Through Applique SHDSL Cut-Through Applique MultiDSL CO-LT Version C - POTS MultiDSL OD-LT Version C - POTS MultiDSL CO-LT Version D - ISDN MultiDSL OD-LT Version D - ISDN FD POTS Only Line Termination Unit version A FD POTS Only Line Termination Unit Version A FD POTS Only Line Termination Unit Version A FD Voice Package Server version A FD Voice Package Server version A FD Voice Package Server version A SHDSL Line Termination Unit version A FD ISDN BRA (2B1Q) LT Unit version A ETSI Passive 48 Port POTS Splitter ETSI Passive 48 Port POTS Splitter with MTA


PSPC PSPC PSPC AFAN AFAN NVLT NVLT NVLT NVLT NVLT NVLT NVLT NVLT ASPS PSPS PSPS PSPS TAUS PSUS PSPB ASPS PSPB PSUB PSUB VSPB VSUB NALT NFXS NANT NANT NANT NANT CTAB CTAS NALT NALT NALT NALT NPOT NPOT NPOT NVPS NVPS NVPS NSLT NBAT NPSP NPSP


7302 ISAM/ISAM-V, 7330 ISAM FTTN, 7360 ISAM FX R4.3.X Software Upgrade MoP 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE

27944 27944 28111 28209 28619 28682 28793 28794 28795 28796 28824 28826 29512 29512 29534 29623 29623 29629 29715 29751 29927 60120 60121 60130 60292 60301 60609 60609 60702 60702 60853 60858 60858 60858 61074 61074 61154 61169 61233 61233 61233 61438 61438 61555 61555 61555 61582 61582 61584 62384 62543 63358 63423 63626

AB AF AA AA AA AA AA AA AA AA AA AA AA AB AA AA BA AA AA AA AA AA AA AF AA BA AA BA AA AB AA AA AB BB BA BB AA AA AA BA BB AA BA AA AB CB AA BA BA AA AA AA AA AA

MII Passive POTS Splitter without MTA MII Passive POTS Splitter with full MTA MII FleXible Density Shelf version A GE NT I/O Applique version B 48 port Passive POTS/ISDN (2B1Q) Splitter FD Ethernet Line Termination MDF Cut-Through Applique 4 lines Passive VDSL-POTS MDF Splitter Version A 4 lines Passive VDSL-POTS/ISDN 2B1Q MDF Splitter 4 lines Passive VDSL-POTS/ISDN 4B3T MDF Splitter Passive VDSL2 Universal 2B1Q Splitter Passive VDSL2 Universal 4B3T Splitter MultiDSL OD-LT Version E - POTS MultiDSL CO-LT Version E - POTS GE NT Applique I/O version D FD Non-MTA Splitter Subrack MII FD Splitter Subrack ETSI Passive 48 Port POTS VDSL Splitter ETSI Passive 48 Port POTS Splitter 48 Ports Passive POTS/ISDN (4B3T) Splitter FD splitter Power I/O FD Test Access Unit Subscriber FD Cut Trough Applique with full MTA Passive Multi DSLPOTS Splitter with MTA Option A Passive POTS Splitter 10GE NT I/O applique version F FD ISDN BRA (2B1Q) LT Unit version B FD ISDN BRA (4B3T) LT Unit version B 48 line FD Wetting Current Applique 24 line FD Wetting Current Applique Flexible Density Cut-through Applique FD POTS Only Line Termination Unit Version B FD POTS Only Line Termination Unit Version B FD POTS Only Line Termination Unit Version B Universal Dummy Front Panel without EMC Gasket Universal Dummy Front Panel with EMC Gasket Passive 48-port VDSL2 over POTS Splitter Passive 48-port ETSI option A POTS Splitter MultiDSL OD Combined LT/Splitter (POTS) MultiDSL CO Combined LT/Splitter (POTS) MultiDSL CO Combined LT/Splitter (POTS) MultiDSL over POTS OD-LT Unit version J MultiDSL over POTS CO-LT Unit version J Combine NT Unit version D Combine NT Unit version D Combine NT Unit version D (MPLS) MultiDSL OD Combined LT/Splitter (ISDN) MultiDSL CO Combined LT/Splitter (ISDN) MultiDSL over ISDN CO-LT Unit version K FD MTA Splitter Subrack FD Ethernet Line termination Unit Version B 48L VDSL2 LT Unit with MELT - version M 72L ADSL2plus LT with MELT - version M SHDSL LT Unit with MELT - version B


Page 6 of 47 NPSP NPSP NFXS NCNC NPSU NELT VCTM VSPM VSUM VSUM NVSU NVSU NALT NALT NCNC NFSS NFSS NVSP NPSP NPSU NPIO NTAU NCTA PSPS NPSP NCNC NBAT NBAT NWCA NWCA NCTA NPOT NPOT NPOT

NVSP NVSP NALS NALS NALS NALT NALT NANT NANT NANT NALS NALS NALT NFSS NELT NVLT NALT NSLT


7302 ISAM/ISAM-V, 7330 ISAM FTTN, 7360 ISAM FX R4.3.X Software Upgrade MoP 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE

63766 63766 63767 63767 64130 64279 64279 64324 64331 64332 64333 64333 64746 64746 65005 65455 65642 65721 65728 65799

AA BA AB BB AA AA AB AA AA AA AA AB AA AB AA AA AA AA AA AA

3FE

65800

AA

3FE 3FE 3FE 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH

65820 65821 65830 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046

AA AA AA AA CA DA EA FA GA HA JA KA LA MA NA PA QA RA SA TA

MultiDSL OD Combined LT/Splitter (POTS) MultiDSL CO Combined LT/Splitter (POTS) MultiDSL over POTS OD LT Unit - version L MultiDSL over POTS CO LT Unit - version L GPON NT I/O Applique version G GPON Line Termination Board - version A GPON Line Termination Board - version A 48L VDSL2 Combined LT/Splitter Unit (POTS) 48L VDSL2 over POTS LT Unit - version P 48L VDSL2 over ISDN LT Unit - version Q 48L VDSL2 LT Unit with MELT - version N 48L VDSL2 LT Unit with MELT - version N Combined NT Unit version E Combined NT Unit version E Dummy Front Panel for NGLT Board FD 48-Line POTS Only LT Unit Version C 10GE NT I/O Applique w/ MPLS - version H Vector Processing Server Board 48p POTS SLV LT (with integrated splitters) 48p POTS SLV LT with MELT (no integrated splitters) 48p POTS SLV LT without MELT (no integrated splitters) 72p VDSL2 LT without MELT 72p VDSL2 LT with MELT 48p POTS BLV LT - version C CWDM SFP Tranceivers IPDSLAM SFP Optical Modules Fast Ethernet SFP Optical Modules Gigabit Ethernet SFP Electrical Modules FE SFP Optical Bidirectional Modules GE BX Optical Modules FE SFP 100Base LX Single Mode with SGMII Multi-rate 10-Gigabit Optical Module GE PX20 Optical Modules Electrical E1-to-GE Convertor Module 10-Gigabit Optical Module 2.5G SFP Electrical FE SFP Electrical E3-to-GE Convertor Module GPON SFP Optical Modules 2.5G BX Optical Modules CSFP Optical Modules

Page 7 of 47 NALS NALS NALT NALT NCNC NGLT NGLT NVLS NVLT NVLT NVLT NVLT NANT NANT NPOT NCNC NDPS NDLS NDLT NDLT NVLT NVLT NDLT SFP SFP SFP SFP SFP SFP SFP XFP SFP SFP SFP SFP SFP SFP SFP SFP SFP

Table 3 : Supported hardware list of 7302 ISAM for R4.3.02




Page 8 of 47

7330 ISAM FTTN R4.3.02 Prefix

Number

Fu Va

3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE

00139 00139 00140 00140 00161 00161 00162 00162 26682 26698 26698 26698 26698 27289 27289 27289 27289 27420 27420 27420 27562 27562 27562 27649 27715 27725 27725 27796 27796 27796 27944 27944 28209 28212 28619 28682 28793 28794 28795 28796 28824 28826 29192 29192 29512 29512 29534 29629 29655 29655 29715

AA BA AA BA AA AB AA AB BA AA AB DA DB AA AB BA BB AA AB AC AA AB AC AA AA AA AF AC AD AE AB AF AA AA AA AA AA AA AA AA AA AA AA AB AA AB AA AA AA AB AA

Name

Mnemonic

48-port VDSL2 over POTS LT Unit vers. C 48-port Shielded VDSL2 over POTS LT Unit vers. C 48-port VDSL2 over ISDN LT Unit vers. D 48-port Shielded VDSL2 over ISDN LT Unit vers. D 48-port VDSL2 over ISDN LT Unit vers.H 48-port VDSL2 over ISDN LT Unit vers.H 48-port VDSL2 over POTS LT Unit vers. G 48-port VDSL2 over POTS LT Unit vers. G MultiDSL LT Unit version B Combined NT Unit version A Combined NT Unit version A Combined NT Unit version A Combined NT Unit version A MultiDSL CO-LT Version C - POTS MultiDSL OD-LT Version C - POTS MultiDSL CO-LT Version D - ISDN MultiDSL OD-LT Version D - ISDN FD POTS Only Line Termination Unit version A FD POTS Only Line Termination Unit Version A FD POTS Only Line Termination Unit Version A FD Voice Package Server version A FD Voice Package Server version A FD Voice Package Server version A SHDSL Line Termination Unit version A FD ISDN BRA (2B1Q) LT Unit version A ETSI Passive 48 Port POTS Splitter ETSI Passive 48 Port POTS Splitter with MTA Flexible Density Shelf - version B Flexible Density Shelf - version B Flexible Density Shelf - version B MII Passive POTS Splitter without MTA MII Passive POTS Splitter with full MTA GE NT I/O Applique version B GE NT I/O Applique version C 48 port Passive POTS/ISDN (2B1Q) Splitter FD Ethernet Line Termination MDF Cut-Through Applique 4 lines Passive VDSL-POTS MDF Splitter Version A 4 lines Passive VDSL-POTS/ISDN 2B1Q MDF Splitter 4 lines Passive VDSL-POTS/ISDN 4B3T MDF Splitter Passive VDSL2 Universal 2B1Q Splitter Passive VDSL2 Universal 4B3T Splitter Standard Fan Unit Low Acoustic Noise Fan Unit MultiDSL OD-LT Version E - POTS MultiDSL CO-LT Version E - POTS GE NT Applique I/O version D ETSI Passive 48 Port POTS VDSL Splitter MII FleXible Density Shelf version B FleXible Density Shelf version B (MII) ETSI Passive 48 Port POTS Splitter


NVLT NVLT NVLT NVLT NVLT NVLT NVLT NVLT NALT NANT NANT NANT NANT NALT NALT NALT NALT NPOT NPOT NPOT NVPS NVPS NVPS NSLT NBAT NPSP NPSP NFXS NFXS NFXS NPSP NPSP NCNC NCNC NPSU NELT VCTM VSPM VSUM VSUM NVSU NVSU AFAN AFAN NALT NALT NCNC NVSP NFXS NFXS NPSP


7302 ISAM/ISAM-V, 7330 ISAM FTTN, 7360 ISAM FX R4.3.X Software Upgrade MoP 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE

29751 29862 29862 60120 60121 60292 60301 60609 60609 60702 60702 60853 60858 60858 60858 61074 61074 61154 61169 61233 61233 61233 61438 61438 61555 61555 61555 61582 61582 61584 62543 63358 63423 63626 63766 63766 63767 63767 64130 64279 64279 64324 64331 64332 64333 64333 64746 64746 65005 65642 65721 65728 65799 65800

AA AA AB AA AA AA BA AA BA AA AB AA AA AB BB BA BB AA AA AA BA BB AA BA AA AB CB AA BA BA AA AA AA AA AA BA AB BB AA AA AB AA AA AA AA AB AA AB AA AA AA AA AA AA

48 Ports Passive POTS/ISDN (4B3T) Splitter GE NT Applique I/O Version E 1GE/2.5GE NT Applique I/O Version E FD Test Access Unit Subscriber FD Cut Trough Applique with full MTA Option A Passive POTS Splitter 10GE NT I/O applique version F FD ISDN BRA (2B1Q) LT Unit version B FD ISDN BRA (4B3T) LT Unit version B 48 line FD Wetting Current Applique 24 line FD Wetting Current Applique Flexible Density Cut-through Applique FD POTS Only Line Termination Unit Version B FD POTS Only Line Termination Unit Version B FD POTS Only Line Termination Unit Version B Universal Dummy Front Panel without EMC Gasket Universal Dummy Front Panel with EMC Gasket Passive 48-port VDSL2 over POTS Splitter Passive 48-port ETSI option A POTS Splitter MultiDSL OD Combined LT/Splitter (POTS) MultiDSL CO Combined LT/Splitter (POTS) MultiDSL CO Combined LT/Splitter (POTS) MultiDSL over POTS OD-LT Unit version J MultiDSL over POTS CO-LT Unit version J Combine NT Unit version D Combine NT Unit version D Combine NT Unit version D (MPLS) MultiDSL OD Combined LT/Splitter (ISDN) MultiDSL CO Combined LT/Splitter (ISDN) MultiDSL over ISDN CO-LT Unit version K FD Ethernet Line termination Unit Version B 48L VDSL2 LT Unit with MELT - version M 72L ADSL2plus LT with MELT - version M SHDSL LT Unit with MELT - version B MultiDSL OD Combined LT/Splitter (POTS) MultiDSL CO Combined LT/Splitter (POTS) MultiDSL over POTS OD LT Unit - version L MultiDSL over POTS CO LT Unit - version L GPON NT I/O Applique version G GPON Line Termination Board - version A GPON Line Termination Board - version A 48L VDSL2 Combined LT/Splitter Unit (POTS) 48L VDSL2 over POTS LT Unit - version P 48L VDSL2 over ISDN LT Unit - version Q 48L VDSL2 LT Unit with MELT - version N 48L VDSL2 LT Unit with MELT - version N Combined NT Unit version E Combined NT Unit version E Dummy Front Panel for NGLT Board 10GE NT I/O Applique w/ MPLS - version H Vector Processing Server Board 48p POTS SLV LT (with integrated splitters) 48p POTS SLV LT with MELT (no integrated splitters) 48p POTS SLV LT without MELT (no integrated splitters)


Page 9 of 47 NPSU NCNC NCNC NTAU NCTA NPSP NCNC NBAT NBAT NWCA NWCA NCTA NPOT NPOT NPOT

NVSP NVSP NALS NALS NALS NALT NALT NANT NANT NANT NALS NALS NALT NELT NVLT NALT NSLT NALS NALS NALT NALT NCNC NGLT NGLT NVLS NVLT NVLT NVLT NVLT NANT NANT NCNC NDPS NDLS NDLT NDLT


7302 ISAM/ISAM-V, 7330 ISAM FTTN, 7360 ISAM FX R4.3.X Software Upgrade MoP 3FE 3FE 3FE 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH

65820 65821 65830 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046

AA AA AA AA CA DA EA FA GA HA JA KA LA MA NA PA QA RA SA TA

72p VDSL2 LT without MELT 72p VDSL2 LT with MELT 48p POTS BLV LT - version C CWDM SFP Tranceivers IPDSLAM SFP Optical Modules Fast Ethernet SFP Optical Modules Gigabit Ethernet SFP Electrical Modules FE SFP Optical Bidirectional Modules GE BX Optical Modules FE SFP 100Base LX Single Mode with SGMII Multi-rate 10-Gigabit Optical Module GE PX20 Optical Modules Electrical E1-to-GE Convertor Module 10-Gigabit Optical Module 2.5G SFP Electrical FE SFP Electrical E3-to-GE Convertor Module GPON SFP Optical Modules 2.5G BX Optical Modules CSFP Optical Modules

Page 10 of 47 NVLT NVLT NDLT SFP SFP SFP SFP SFP SFP SFP XFP SFP SFP SFP SFP SFP SFP SFP SFP SFP

Table 4 : Supported hardware list of 7330 ISAM FTTN for R4.3.02

7360 ISAM FX R4.3.02 Prefix 3EC 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3FE 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH 3HH

Number 37533 53701 53711 54057 62543 64279 64279

64936 64985 64991 64993 64994 65060 65209 65651 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046 01046

Fu Va NB AC AA AA AA AA AB AA AA AA AA AA AA AA AA CA DA EA FA GA LA MA PA QA RA TA UA

Name ADSL FAN Unit with dust filter Combined NT Unit version F EPON Line Termination Board - version A FX FE/GE NT I/O Applique - version B FD Ethernet Line termination Unit Version B GPON Line Termination Board - version A GPON Line Termination Board - version A FX-8 shelf for ETSI/MII General Facility Card version E FX-4 shelf for ETSI/MII General Facility Card version F FX-4 Fan Unit FX-8 Fan Unit FX-16 shelf for ETSI/MII Dummy Front Panel for NT board IPDSLAM SFP Optical Modules Fast Ethernet SFP Optical Modules Gigabit Ethernet SFP Electrical Modules FE SFP Optical Bidirectional Modules GE BX Optical Modules Electrical E1-to-GE Convertor Module 10-Gigabit Optical Module Electrical FE SFP Electrical E3-to-GE Convertor Module GPON SFP Optical Modules CSFP Optical Modules Downstream EPON Optical Modules

Mnemonic AFAN FANT FPLT FNIO NELT NGLT NGLT NFXS NGFC NFXS NGFC AFAN AFAN NFXS SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP

Table 5 : Supported hardware list of 7360 ISAM FX for R4.3.02




Page 11 of 47

1.8. 5520 AMS - ISAM Compatibility 5520 AMS R9.1.0 supports previous ISAM 4.3 Releases and ISAM 4.3.02 Release with R4.3 plug v3.0.




Page 12 of 47

2. SITE VISIT PREPARATION This is the list of items recommended to take with you while going to site. Go through this list before you go to a site-work. As soon as the date/time of the activities confirmed, inform the Fixed Access TAC/TSO group in your region. Share your MOP with the TAC team. It is a good practice to ask them to review your MOPs. Since they are aware of many knownissues, they can make some recommendations. During the activity, if you have any issues you will need to raise a Support Ticket in order to get a remote support.

2.1. Information Checklist Fill the form below: No

Information

Explanation

1

Box Configurations

2 3

Site Address & Location Site Security Permission

4

Site Contact Person

5

Scope of Work

6

Remote Access Configurations

See the “Box Configuration” section in this chapter. Do you have additional config file to apply the box? Do you have the information to go there? Did you arrange the site security permission for the planned date & time? Who (from the customer site) will be in charge for your visit? Do you know what operations/tasks will you be responsible for? Do you have a written statement confirmed by the customer? Far end devices configurations needs to be done by the customer or 3rd parties or by yourself.

Table 6 : Site-Visit Information Checklist

2.2. Tools and Devices No

Material

For Use

1 2

Console Cable Antistatic wrist strap

3 4

External USB Hard Disk USB Flash Disk

5

Screw Driver

6

Pen and paper

7

Labeling Stickers

8

Laptop with Com port or USB to Serial convertor (Male) Terminal Program

To connect to the box locally Always use the antistatic wrist strap before you touch the hardware To store Backups, SW loads, configurations Document and file sharing/transfer with the customer or 3rd parties To mount a fresh product on-site / To tighten the loose screws To take notes while sharing some information with the customer Different sized of stickers to label the box, cable endpoints etc. To connect to the box locally

9

For example Putty, MS Terminal, Hummingbird Table 7 : Tools and Devices for site visit




Page 13 of 47

2.3. Personnel in Charge The following personnel will be involved in the activity: Name of personnel e.g Karl Fredrich Gauss e.g Leonhard Euler

Role

Contact numbers

e.g. Router Configuration Engineer – Alcatel-Lucent e.g 5620 SAM Engineer – Seven Bridges of Königsberg Telecom Table 8: Personnel in Charge

2.4. Escalation Procedure During the activity, if any problem occurs then the following engineers and/or people in charge should be notified for further actions. Proponent Name/Group/Contact Number: e.g Edsger Dijkstra / FAE / +90530… IS/Contact Number: e.g Richard Bellman / FO/ +90540… Next Level IS: e.g Lester Ford, Jr / +90505… Implementor Name/Group/Contact Number: e.g Bernhard Riemann /ALU / +90530.. IS/Contact Number: e.g Isaac Newton / ALU / +90540… Next Level IS: e.g Gottfried Leibniz / ALU / +90505… Change Control Name/Contact Number: e.g Max Planck / +90530… IS/Contact Number: e.g Paul Dirac / +90540… Next Level IS: e.g Richard Feynman / +90505… Information to Raise a Support Ticket Welcome Center Phone Welcome Center Email Address Customer Name Customer Support Contract No -




Page 14 of 47

2.5. Box Configurations Fill and check the box configuration table with required information before going site. It is recommended to populate the form below for each box and attach on the equipment before delivering to the field. For each server & shelf, fill a separate form as below. Box Specifications Location Serial Number Role1 Role2 Redundancy Shelf Model

Geographical location of device Enter chassis serial number here Primary Server Secondary Server e.g. Collocated/Distributed NFXS-A

Power Supply Faults Management TCP/IP Config Management Access Method Management User Name Management Password IP1 Configurations IP2 Configurations System Login Info CLI password TL1 password Host id

What are the power requirements of the device? Any faults seen at the before/after the installation e.g. IP address for accessing the device e.g. telnet, ssh or http e.g. root e.g. changeme bge0 : 212.156.115.164/24 ; GW : 212.156.115.254 bge1 : 10.1.1.100/24 e.g. root e.g. password e.g. password Table 9 : Box Configuration




Page 15 of 47

2.6. Timetable Fill the activity timetable below according to your plan. Columns starts with “proposal” should be filled in before the activity and columns with “actual” will be filled in after the password recovery activity. Activity Details and Coordination Item Description

Proposed Proposed End Start Date/Time Date/Time

eg. Personnel Check

21st Dec 21:30

21st Dec 21:40

eg. Preliminary Work Lists

… …

…

eg. Reboot the router

Actual Start Date/Time

Actual End Date/Time

…

e.g Zero Config Startup… e.g. Execute the original config e.g. Service and Traffic Check e.g. Rebooting the Box ( Service Interruption )

Table 10: Timetable




Page 16 of 47

3. PRE-UPGRADE TASKS This section will give detailed information about the tasks that needs to be done before starting upgrade procedure.

3.1. Pre-Upgrade Checklist Entrance Criteria The “Site Visit Preparation” section should be completed. Pre-Software Upgrade Checklist 1 Verify that you have remote connection to management server 2 Verify that you have username and password for Unix login Verify that you have username and password to login via CLI to 3 7302 ISAM, 7330 ISAM FTTN or 7360 ISAM FX. 4 Verify that required software downloaded from OLCS Verify that Software package transferred to 5520 AMS 5 successfully MOP and Activity Date/Time Information Shared with Fixed 6 Access TSO/TAC group

Applied

Table 11: Pre-Software Upgrade Checklist

3.2. Getting the Software Before starting the software upgrade, you need to download the required software. Download the related release that is going to be installed from the Alcatel-Lucent Market site: https://support.alcatel-lucent.com/portal/olcsHome.do 1. Log in to Alcatel-Lucent Market.




Page 17 of 47

Figure 1: Log in to Alcatel-Lucent Market

2. Select the related product.

Figure 2: Selecting the Correct Hardware Model

3. Click on the link "Downloads: Electronic Delivery". 4. Select the related release then click on “Next” button.




Page 18 of 47

Figure 3: Select Proper Software Release then click on “Next” button

5. Enter the download directory then click on the “Download” button.

Figure 4: Enter the download directory then click on the “Download” button

6. Please see the “Download Succeeded” pop-up. The download time may vary with internet bandwidth.




Page 19 of 47

4. SOFTWARE UPGRADE VIA AMS For ISAM software upgrade, please follow the procedures in below. In the section, for ISAM software migration AMS server used as TFTP server and from the AMS GUI the software download & upgrade actions are commenced.

4.1. Upgrade Checklist Entrance Criteria The “Pre-Upgrade Tasks” section should be completed. Pre-Installation Checklist 1 Verify that ISAM software package unzipped successfully Verify that software and descriptor file prepared at designated 2 folder Verify that new software release defined to AMS Software 3 section 4 Verify that new software downloaded to ISAM successfully 5 Verify that new software version is active after upgrade

Applied

Table 12: Pre-Installation Checklist

4.2. Upload the Downloaded Software Release to the AMS Server Before uploading the software to AMS server, please check the ISAM OSWP table from software management to find out which release or software working on ISAM. One OSWP should be empty, if not, commit the active software which will clear the other OSWP. leg:isadmin># show software-mngt oswp ================================================================ ======================== oswp table ================================================================ ======================== | | | |commit index|name |availability|act-status|status -----+---------------------------------------------+------------+----------+-----------1 L6GPAZ42.216 enabled active committed 2 NO_OSWP empty not-active un-committed ---------------------------------------------------------------------------------------oswp count : 2 ================================================================= ======================= leg:isadmin># Table 13: List OSWP




Page 20 of 47

Create a temporary folder in the AMS server that will be used during software preparation. In the document,” Upgrade_SW” is the name of the temporary folder bash-3.00# cd / bash-3.00# mkdir Upgrade_SW bash-3.00# chmod 777 Upgrade_SW/ Table 14: Temporary Folder Creation

After that new software can be uploaded to AMS server via remote connection by typing the following command: scp username@: Table 15: Secure Copy

After upload process completed successfully, the upgrade procedure can be started on the AMS.

4.3. Preparing the Software for Upgrade Connect to the 5520 AMS server via SSH or Telnet with root privileges and then: 1. Unzip the ISAM software package that transferred at section “Upload the

Downloaded Software Release to the AMS Server”

bash-3.00# cd /Upgrade_SW/ bash-3.00# tar -xf ISAM4_3.tar bash-3.00# ls -lart total 638726 drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 Migration_tool drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 ISAM_migration drwxr-xr-x 2 21058 3610 4 Jul 31 02:11 ISAM drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 xVPS_migration drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 SHub_migration -rw-rw-rw- 1 21058 3610 4174 Jul 31 02:11 readme.txt drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 CDE_profiles drwxr-xr-x 2 21058 3610 6 Jul 31 23:17 docs -rwxr-xr-x 1 root amssys 326758400 Aug 13 16:11 ISAM4_3.tar drwxr-xr-x 34 root root 39 Aug 14 14:03 .. drwxrwxrwx 9 root root 11 Aug 14 14:07 Table 16: Untar ISAM Package




Page 21 of 47

2. Navigate to “ISAM” folder under the “Upgrade_SW” and check the software

file and descriptor file.

bash-3.00# cd ISAM bash-3.00# ls -lart total 580537 -r--r--r-- 1 21058 3610 296990720 Jul 30 14:13 L6GQAA43.170.tar -rw-r--r-- 1 21058 3610 143 Jul 31 02:11 L6GPAA43.170 drwxr-xr-x 2 21058 3610 4 Jul 31 02:11 . drwxrwxrwx 9 root root 11 Aug 14 14:07 .. bash-3.00# chmod 777 L6G* bash-3.00# ls -lart total 580537 -rwxrwxrwx 1 21058 3610 296990720 Jul 30 14:13 L6GQAA43.170.tar -rwxrwxrwx 1 21058 3610 143 Jul 31 02:11 L6GPAA43.170 drwxrwx--- 6 amssys amssys 6 Aug 3 16:26 .. drwxrwx--- 2 amssys amssys 4 Aug 14 14:21 . bash-3.00# Table 17: Navigate to ISAM dir

3. Move both software & descriptor file to

“/var/opt/ams/shared/common/ne/software”

bash-3.00# mv L6G* /var/opt/ams/shared/common/ne/software bash-3.00# cd /var/opt/ams/shared/common/ne/software bash-3.00# ls -lart total 580537 -rwxrwxrwx 1 21058 3610 296990720 Jul 30 14:13 L6GQAA43.170.tar -rwxrwxrwx 1 21058 3610 143 Jul 31 02:11 L6GPAA43.170 drwxrwx--- 6 amssys amssys 6 Aug 3 16:26 .. drwxrwx--- 2 amssys amssys 4 Aug 14 14:21 . bash-3.00# Table 18: Move Descriptor File

4. Editing descriptor file to match TFTP server IP address which is the AMS

server IP address for this procedure. bash-3.00# vi L6GPAA43.170 "L6GPAA43.170" 5 lines, 143 characters ; OVERALL-DESCRIPTOR-FILE L6GPAA43.170 BEGIN SYNTAX-VERSION : 01.00; ASAM-CORE : /L6GQAA43.170 0.0.0.0; END bash-3.00# cat L6GPAA43.170 OVERALL-DESCRIPTOR-FILE L6GPAA43.170 BEGIN SYNTAX-VERSION : 01.00; ASAM-CORE : /L6GQAA43.170 172.29.7.249 0.0.0.0; END bash-3.00# Copyright @ Alcatel-Lucent GPEC TEAM



Page 22 of 47

Table 19: Overall-Descriptor file

4.4. Adding New Software Release to 5520 AMS After preparing software files, software upgrade can be done by following procedure: 1. Login to the 5520 AMS GUI with AMS client 2. Click on the “Perspective Menu (1) -> Software (2)” on AMS menu to open the NE Software File Preparation window.

Figure 5 : NE Software File Preparation

3. Right click on the “New SW Releases under Software Releases” and create NW SW release.




Page 23 of 47

Figure 6 : Create New SW Load

4. Select NE type/Release, Name and Description. Name should be on “L6GPAAxy.klm” format. Easily give the same name as the software load after changing the 4th character Q with P.

Figure 7 : Add New Software Delivery




Page 24 of 47

5. Select the proper SW file from the table and press to “Finish”.

Figure 8 : Selecting Software File

4.5. Downloading New Software to an NE 1. Click on the Open Perspective icon on 5520 AMS GUI main screen and choose Software from the perspectives menu.

Figure 9 : Choose software from the Perspective




Page 25 of 47

2. Pick up “Download Software to NE” on “SW Tasks” menu and click on “Add” button to choose NE’s to download new software.

Figure 10 : Download SW to NE

3. Select any filter and press to “Build List” choose NE’s on 5520 AMS and click on Finish.

Figure 11: Selecting NE




Page 26 of 47

4. Press to “Finish” to start software download to ISAM

Figure 12 : Finishing Software Download Preparation

5. Software Download Process will be start.

Figure 13: Software Download to NE

6. Check the software download from the ISAM OSWP table Copyright @ Alcatel-Lucent GPEC TEAM



Page 27 of 47

leg:isadmin># show software-mngt oswp detail ===================================================== ===================== oswp table (detailed) ===================================================== ===================== -------------------------------------------------------------------------oswp -------------------------------------------------------------------------index : 1 name : OSWP/172.29.7.249/L6GPAA42.440/L6GPAA42.440 availability : downloading act-status : not-active commit-status : un-committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error -------------------------------------------------------------------------oswp -------------------------------------------------------------------------index : 2 name : L6GPAA42.401 availability : enabled act-status : active commit-status : committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error ===================================================== =================== Table 20: Check version after download

7. When download procedure ends, a result window will be pop-up.

4.6. Activating the New Software via AMS 1. Pick up “Activate NE Software” on “SW Tasks” menu of “Software”.




Page 28 of 47

Figure 14 : NE Software Activation




Page 29 of 47

2. Press to “Add” button and then select any filter and press to “Build List” choose NE’s on 5520 AMS and click on Finish.

Figure 15: NE selection

3. Review the selected NE’s once again and press to “Next”.

Figure 16: Review Selected NE's




Page 30 of 47

4. Choose action and click on Finish to start software activation.

Figure 17: Starting NE Software Activation

Figure 18 : Activation

5. When activation finishes, a result windows will be pop-up.




Page 31 of 47

5. SOFTWARE UPGRADE VIA TL1 For ISAM software upgrade, please follow the procedures in below. In the section, AMS server used as a TFTP server, for transferring the new software load to ISAM. However another TFTP server or TFTP software can be used. Software download to ISAM & software activation initialized from the ISAM TL1 connection.

5.1. Upgrade Checklist Entrance Criteria The “Pre-Upgrade Tasks” section should be completed. Pre-Installation Checklist 1 Verify that ISAM software package transferred successfully. 2 Verify that ISAM software package unzipped successfully Verify that software and descriptor file prepared at designated 3 folder 4 Verify that one OSWP is empty. 5 Verify that new software downloaded to ISAM successfully 6 Verify that new software version is active after upgrade

Applied


5.2. Upload New Software Release to the AMS server Before uploading the software to AMS server, please check the ISAM OSWP table from software management to find out which release or software working on ISAM. One OSWP should be empty, if not, commit the active software which will clear the other OSWP. leg:isadmin># show software-mngt oswp ================================================================ ======================== oswp table ================================================================ ======================== | | | |commit index|name |availability|act-status|status -----+---------------------------------------------+------------+----------+-----------1 L6GPAZ42.216 enabled active committed 2 NO_OSWP empty not-active un-committed ---------------------------------------------------------------------------------------oswp count : 2 ================================================================= ======================= leg:isadmin># Table 22: List OSWP

Create a temporary folder in the AMS server that will be used during software preparation. In the document,” Upgrade_SW” is the name of the temporary folder Copyright @ Alcatel-Lucent GPEC TEAM



Page 32 of 47

bash-3.00# cd / bash-3.00# mkdir Upgrade_SW bash-3.00# chmod 777 Upgrade_SW/ Table 23: Temporary Folder Creation

After that new software can be uploaded to AMS server via remote connection by typing the following command:

scp username@: Table 24: Secure Copy

After upload process completed successfully, the upgrade procedure can be started on the AMS.




Page 33 of 47

5.3. Preparing the Software for Upgrade Connect to the 5520 AMS server via SSH or Telnet with root privileges and then: 1. Unzip the ISAM software package that transferred at section “Upload New

Software Release to the AMS server” bash-3.00# cd /Upgrade_SW/ bash-3.00# tar -xf ISAM4_3.tar bash-3.00# ls -lart total 638726 drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 Migration_tool drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 ISAM_migration drwxr-xr-x 2 21058 3610 4 Jul 31 02:11 ISAM drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 xVPS_migration drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 SHub_migration -rw-rw-rw- 1 21058 3610 4174 Jul 31 02:11 readme.txt drwxr-xr-x 2 21058 3610 3 Jul 31 02:11 CDE_profiles drwxr-xr-x 2 21058 3610 6 Jul 31 23:17 docs -rwxr-xr-x 1 root amssys 326758400 Aug 13 16:11 ISAM4_3.tar drwxr-xr-x 34 root root 39 Aug 14 14:03 .. drwxrwxrwx 9 root root 11 Aug 14 14:07 Table 25: Untar ISAM Package

2. Navigate to “ISAM” folder under the “Upgrade_SW” and check the software

file and descriptor file.

bash-3.00# cd ISAM bash-3.00# ls -lart total 580537 -r--r--r-- 1 21058 3610 296990720 Jul 30 14:13 L6GQAA43.170.tar -rw-r--r-- 1 21058 3610 143 Jul 31 02:11 L6GPAA43.170 drwxr-xr-x 2 21058 3610 4 Jul 31 02:11 . drwxrwxrwx 9 root root 11 Aug 14 14:07 .. bash-3.00# chmod 777 L6G* bash-3.00# ls -lart total 580537 -rwxrwxrwx 1 21058 3610 296990720 Jul 30 14:13 L6GQAA43.170.tar -rwxrwxrwx 1 21058 3610 143 Jul 31 02:11 L6GPAA43.170 drwxrwx--- 6 amssys amssys 6 Aug 3 16:26 .. drwxrwx--- 2 amssys amssys 4 Aug 14 14:21 . bash-3.00# Table 26: Navigate to ISAM dir




Page 34 of 47

3. Move both software & descriptor file to

“/var/opt/ams/shared/common/ne/software”

bash-3.00# mv L6G* /var/opt/ams/shared/common/ne/software bash-3.00# cd /var/opt/ams/shared/common/ne/software bash-3.00# ls -lart total 580537 -rwxrwxrwx 1 21058 3610 296990720 Jul 30 14:13 L6GQAA43.170.tar -rwxrwxrwx 1 21058 3610 143 Jul 31 02:11 L6GPAA43.170 drwxrwx--- 6 amssys amssys 6 Aug 3 16:26 .. drwxrwx--- 2 amssys amssys 4 Aug 14 14:21 . bash-3.00# Table 27: Move Descriptor File

4. Editing descriptor file to match TFTP server IP address which is the AMS

server IP address for this procedure. bash-3.00# vi L6GPAA43.170 "L6GPAA43.170" 5 lines, 143 characters ; OVERALL-DESCRIPTOR-FILE L6GPAA43.170 BEGIN SYNTAX-VERSION : 01.00; ASAM-CORE : /L6GQAA43.170 0.0.0.0; END bash-3.00# cat L6GPAA43.170 OVERALL-DESCRIPTOR-FILE L6GPAA43.170 BEGIN SYNTAX-VERSION : 01.00; ASAM-CORE : /L6GQAA43.170 172.29.7.249 0.0.0.0; END bash-3.00# Table 28: Overall-Descriptor file




Page 35 of 47

5.4. Downloading New Software to an NE 1. Login to ISAM node via TL1. Before downloading the software to ISAM node, please check the ISAM OSWP table from software management to find out which release or software working on ISAM. One OSWP should be empty, if not, commit the active software which will clear the other OSWP. REPT-OPSTAT-OSWP::ALL:: "OSWP-1:AVAILSTAT,ENABLED" "OSWP-1:ACTSTAT,ACTIVE" "OSWP-1:COMMITSTAT,COMMITTED" "OSWP-1:AUTOACTVERR,NOERROR" "OSWP-2:AVAILSTAT,EMPTY" "OSWP-2:ACTSTAT,NOTACTIVE" "OSWP-2:COMMITSTAT,UNCOMMITTED" "OSWP-2:AUTOACTVERR,NOERROR" Table 29: List OSWP

ED-OSWP::OSWP-2::::ACTIVATION=,COMMITMENT=,ABORT=TRUE,AUTOACTIVE= Table 30: Deleting OSWP

2. Download new software to ISAM node. DL-OSWP:::::,, DL-OSWP:::::172.29.7.249,,L6GPAA43.170 Table 31: Downloading New Software

REPT-OPSTAT-OSWPDL::OSWP-2:: "OSWP-2:DLPROGRESS,DOWNLOADING" "OSWP-2:DLERROR,NOERROR" "OSWP-2:COMPSET,148" "OSWP-2:AVAILCOMPSET,34" "OSWP-2:TOTALDISK,374423552" "OSWP-2:FREEDISK,181411840" "OSWP-2:DLSERVPRI,172.29.7.249" "OSWP-2:DLSERVSEC,0.0.0.0" "OSWP-2:PACKNAME,L6GPAA43.170" Table 32: Downloading Progress




Page 36 of 47

REPT-OPSTAT-OSWPDL::OSWP-2:: "OSWP-2:DLPROGRESS,ENABLED" "OSWP-2:DLERROR,NOERROR" "OSWP-2:COMPSET,148" "OSWP-2:AVAILCOMPSET,37" "OSWP-2:TOTALDISK,374423552" "OSWP-2:FREEDISK,139427840" "OSWP-2:DLSERVPRI,172.29.7.249" "OSWP-2:DLSERVSEC,0.0.0.0" "OSWP-2:PACKNAME,L6GPAA43.170" Table 33: Downloading Result

5.5. Activating the New Software via TL1 1. Login to ISAM node via TL1 & activate the new software package. ED-OSWP::OSWP-2::::ACTIVATION=WITHDEFDB,COMMITMENT=,ABORT=,AUTOACTIVE= Table 34: Activate the New Software

2. Check OSWP status of ISAM node. REPT-OPSTAT-OSWP::ALL:: "OSWP-1:AVAILSTAT,ENABLED" "OSWP-1:ACTSTAT,NOTACTIVE" "OSWP-1:COMMITSTAT,COMMITTED" "OSWP-1:AUTOACTVERR,NOERROR" "OSWP-2:AVAILSTAT,ENABLED" "OSWP-2:ACTSTAT,ACTIVE" "OSWP-2:COMMITSTAT,UNCOMMITTED" "OSWP-2:AUTOACTVERR,NOERROR" Table 35: Check OSWP Status




Page 37 of 47

6. SOFTWARE UPGRADE VIA CLI For ISAM software upgrade, please follow the procedures in below. Software download to ISAM & software activation initialized from the ISAM CLI connection.

6.1. Upgrade Checklist Entrance Criteria The “Pre-Upgrade Tasks” section should be completed. Pre-Installation Checklist Verify that TFTP software started and accepting TFTP 1 connection requests 2 Verify that ISAM software package unzipped successfully Verify that software and descriptor file prepared at designated 3 folder 4 Verify that one OSWP is empty. 5 Verify that new software downloaded to ISAM successfully 6 Verify that new software version is active after upgrade

Applied


6.2. Preparing the Software for Upgrade 1. Extract “ISAM4_3.tar” software file downloaded from “OLCS”. 2. There should be “ISAM” folder in extracted files. Double click the “ISAM” folder and move the “L6GPAA43.279” and “L6GQAA43.279.tar” files to TFTP root folder of the related AMS server(for 5520 AMS R9.1 “/ams/swm/ne”). 3. Give an IP address to your personal computer in the same network with ISAM. 4. Edit the “L6GPAA43.170” descriptor file with “vi editor”. Edit the path and filename of the software package file “L6GQAA43.170” also IP address of the TFTP server. bash-3.00# vi L6GPAA43.170 "L6GPAA43.170" 5 lines, 143 characters ; OVERALL-DESCRIPTOR-FILE L6GPAA43.170 BEGIN SYNTAX-VERSION : 01.00; ASAM-CORE : /L6GQAA43.170 0.0.0.0; END




Page 38 of 47

bash-3.00# cat L6GPAA43.170 OVERALL-DESCRIPTOR-FILE L6GPAA43.170 BEGIN SYNTAX-VERSION : 01.00; ASAM-CORE : /L6GQAA43.170 172.29.7.249 0.0.0.0; END bash-3.00#

Table 37: Overall-Descriptor file

a) Extract the “L6GQAA43.170.tar” file in TFTP root folder.

6.3. Downloading New Software to an NE 1. Login to ISAM node via CLI. Before downloading the software to ISAM node, please check the ISAM OSWP table to find out which software package working on ISAM. One OSWP should be empty, if not, commit the active software which will clear the other OSWP or abort-download not-active OSWP. leg:isadmin># show software-mngt oswp detail ================================================================================ oswp table (detailed) ================================================================================ -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 1 name : L6GPAA43.255 availability : enabled act-status : active commit-status : committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 2 name : L6GPAA42.413 availability : enabled act-status : not-active commit-status : un-committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error ================================================================================ Table 38: Check the OSWP Table




Page 39 of 47

leg:isadmin># admin software-mngt oswp 2 abort-download leg:isadmin># show software-mngt oswp detail ================================================================================ oswp table (detailed) ================================================================================ -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 1 name : L6GPAA43.255 availability : enabled act-status : active commit-status : committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 2 name : NO_OSWP availability : empty act-status : not-active commit-status : un-committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error ================================================================================ Table 39: Abort the Not-Active OSWP

First configure the TFTP server IP address. leg:isadmin># configure software-mngt oswp 2 primary-file-server-id 172.29.7.249 Table 40: Configure the TFTP Server IP Address

Download the new software to ISAM. leg:isadmin># admin software-mngt oswp 2 download L6GPAA43.170 Table 41: Configure the TFTP Server IP Address




Page 40 of 47

leg:isadmin># show software-mngt oswp detail ================================================================================ oswp table (detailed) ================================================================================ -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 1 name : L6GPAA43.255 availability : enabled act-status : active commit-status : committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 2 name : L6GPAA43.170 availability : downloading act-status : not-active commit-status : un-committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error ================================================================================ leg:isadmin># show software-mngt oswp detail ================================================================================ oswp table (detailed) ================================================================================ -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 1 name : L6GPAA43.255 availability : enabled act-status : active commit-status : committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error -------------------------------------------------------------------------------oswp -------------------------------------------------------------------------------index : 2 name : L6GPAA43.170 availability : enabled act-status : not-active commit-status : un-committed download-error : no-error err-file-name : err-file-server : 0.0.0.0 auto-activate-error : no-error ================================================================================ Table 42: Check Download Status




Page 41 of 47

6.4. Activating the New Software via CLI Activate the new software package from the CLI leg:isadmin># admin software-mngt oswp 2 activate with-default-db #OR to save the configuration with the last configured DB: leg:isadmin># admin software-mngt oswp 2 activate with-linked-db Table 43: Activate the New Software




Page 42 of 47

7. Post-Software Upgrade Checklist 1 2 3

Post- Software Upgrade Checklist Verify the upgrade operation is successfully completed Verify that 7302 ISAM/ISAM-V , 7330 ISAM FTTN or 7360 ISAM FX is back online after software activation Verify the new software version Exit Criteria

Applied

The proper Software Upgrade section should be completed.

Table 44: Post-SW Upgrade Checklist




Page 43 of 47

APPENDIX A. INDEX OF TABLES TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE TABLE

1 : DOCUMENT REVISION HISTORY...............................................................................3 2 : DOCUMENT LIST.............................................................................................4 3 : SUPPORTED HARDWARE LIST OF 7302 ISAM FOR R4.3.02...................................................7 4 : SUPPORTED HARDWARE LIST OF 7330 ISAM FTTN FOR R4.3.02..........................................10 6 : SUPPORTED HARDWARE LIST OF 7360 ISAM FX FOR R4.3.02..............................................11 7 : SITE-VISIT INFORMATION CHECKLIST........................................................................12 8 : TOOLS AND DEVICES FOR SITE VISIT........................................................................12 9: PERSONNEL IN CHARGE......................................................................................13 10 : BOX CONFIGURATION.....................................................................................14 11: TIMETABLE................................................................................................. 15 12: PRE-SOFTWARE UPGRADE CHECKLIST......................................................................16 13: PRE-INSTALLATION CHECKLIST.............................................................................19 14: LIST OSWP............................................................................................... 19 15: TEMPORARY FOLDER CREATION............................................................................20 16: SECURE COPY............................................................................................. 20 17: UNTAR ISAM PACKAGE....................................................................................20 18: NAVIGATE TO ISAM DIR....................................................................................21 19: MOVE DESCRIPTOR FILE....................................................................................21 20: OVERALL-DESCRIPTOR FILE.................................................................................21 21: CHECK VERSION AFTER DOWNLOAD.........................................................................27 22: PRE-INSTALLATION CHECKLIST.............................................................................30 23: LIST OSWP............................................................................................... 30 24: TEMPORARY FOLDER CREATION............................................................................31 25: SECURE COPY............................................................................................. 31 26: UNTAR ISAM PACKAGE....................................................................................32 27: NAVIGATE TO ISAM DIR....................................................................................32 28: MOVE DESCRIPTOR FILE....................................................................................33 29: OVERALL-DESCRIPTOR FILE.................................................................................33 30: LIST OSWP............................................................................................... 34 31: DELETING OSWP.......................................................................................... 34 32: DOWNLOADING NEW SOFTWARE............................................................................34 33: DOWNLOADING PROGRESS.................................................................................34 34: DOWNLOADING RESULT....................................................................................35 35: ACTIVATE THE NEW SOFTWARE.............................................................................35 36: CHECK OSWP STATUS.....................................................................................35 37: PRE-INSTALLATION CHECKLIST.............................................................................36 38: OVERALL-DESCRIPTOR FILE.................................................................................37 39: CHECK THE OSWP TABLE.................................................................................37 40: ABORT THE NOT-ACTIVE OSWP...........................................................................38 41: CONFIGURE THE TFTP SERVER IP ADDRESS................................................................38 42: CONFIGURE THE TFTP SERVER IP ADDRESS................................................................38 43: CHECK DOWNLOAD STATUS................................................................................39 44: ACTIVATE THE NEW SOFTWARE.............................................................................40 45: POST-SW UPGRADE CHECKLIST............................................................................41





Page 44 of 47



Page 45 of 47

APPENDIX B. INDEX OF FIGURES FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE FIGURE

1: LOG IN TO ALCATEL-LUCENT MARKET......................................................................16 2: SELECTING THE CORRECT HARDWARE MODEL...............................................................17 3: SELECT PROPER SOFTWARE RELEASE THEN CLICK ON “NEXT” BUTTON......................................17 4: ENTER THE DOWNLOAD DIRECTORY THEN CLICK ON THE “DOWNLOAD” BUTTON.............................18 5 : NE SOFTWARE FILE PREPARATION.........................................................................22 6 : CREATE NEW SW LOAD...................................................................................22 7 : ADD NEW SOFTWARE DELIVERY............................................................................23 8 : SELECTING SOFTWARE FILE................................................................................24 9 : CHOOSE SOFTWARE FROM THE PERSPECTIVE...............................................................24 10 : DOWNLOAD SW TO NE..................................................................................25 11: SELECTING NE............................................................................................ 25 12 : FINISHING SOFTWARE DOWNLOAD PREPARATION..........................................................26 13: SOFTWARE DOWNLOAD TO NE............................................................................26 14 : NE SOFTWARE ACTIVATION...............................................................................27 15: NE SELECTION............................................................................................ 28 16: REVIEW SELECTED NE'S...................................................................................28 17: STARTING NE SOFTWARE ACTIVATION.....................................................................29 18 : ACTIVATION.............................................................................................. 29




Page 46 of 47

APPENDIX C. REFERENCES No references.




Page 47 of 47

APPENDIX D. GLOSSARY ADSL AMS ETSI FD ISAM LT NT OSWP SCP SSH TFTP

Asymmetric Digital Subscriber Line ACCESS MANAGEMENT SYSTEM European Telecommunications Standard Institute Flexible Density Intelligent Services Access Manager Line Termination Network Termination Over-all SoftWare Package Secure CoPy Secure Shell Trivial File Transfer Protocol



3FQ-24068-43XU-PGZZA-07-RPEC Fixed Access 7302-7330-7360 ISAM R4_3_X Software Upgrade MOP.doc

Recommend Documents