Upgrade guide

SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS ELECTRONICS CO., LTD. L TD.

DC-7 UPGRADE INSTRUCTION INSTRUCTION V03.00.00.62183(ECN018) V03.00.00.62183(ECN018)

SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS ELECTRONICS CO., LTD. L TD.

REVISION CONTROL Document Title:

DC-7 upgrade instruction instruction

Author:

Mindray International Service Department

Date

By

Action

Pages

Jan 5, 2011

Klaus Klaus Hu

New format format

All

Action

Pages

Review/Approval History Date

By

Page 2 of 27

SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD.

Contents Page 1

BEFORE UPGRADE................................................................................................................................................ 4

2

UPGRADE STEP ONE – BIOS UP DATE............................................................................................................ 6

FILE: USB_BOOT.ZIP ..................................................................................................................................................... 7 METHOD: ........................................................................................................................................................................... 8 3

UPGRADE STEP TWO – CHANGE BIOS SETTING TO BOOT FROM CD ...........................................11

4

UPGRADE STEP THREE --- WINDOWS XP SYSTEM UPDATE..............................................................15

5

UPGRADE STEP FOUR --- DOPPLER UPDATE ...........................................................................................1 8

6

UPGRADE STEP FIVE --- CHANGE BIOS SETTING TO DISABLE BOOT FROM CD......................21

7

UPGRADE STEP SIX --- CHANGE LANGUAGE...........................................................................................24

8

UPGRADE STEP SEVEN --- INSTALL KEYS FOR ALL APPLICATION EXAMS...............................25

9

UPGRADE STEP EIGHT --- LOAD PRESET DATA ..................................................................................... 26

10

UPGRADE STEP NINE--- CALIBRATE TOUCH SCREEN.........................................................................27

Page 3 of 27


1

Before upgrade

1)

You need the following items YOU MUST HAVE 1.

USB port PC mouse

2.

A empty virus-free USB stick

3.

DISK 1: windows XP disk

4.

DISK 2: Doppler Software disk

5.

Disk 3: USB_Boot.zip and DC-7 Bios update files

Note:

Page 4 of 27

SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD. 1.

Please inquire Mindray Service Department to obtain upgrade disks or download disk image files from designated website and restore them onto disks by yourself.

2.

If you choose to download software package from website, please restore bootable CD1 from recovery_cd_2.iso (CD image file) by CD burning software such as NERO and burn the contents like shown below extracted from CD2.zip into CD2.

2) You should know: Point 1

User preset data will be deleted after upgrade. We strongly recommend you do backup before upgrade. How to back up user preset data to USB stick? Press [F10] key on PC keyboard  [Manage settings] menu  [Export all] menu (on the bottom left) Give a name for the preset data file. Select drive of USB stick. Click “OK”.

How to reload user preset data? [Import all] on [manage settings] page

 Click

on the saved data file in USB stick.

After loading bar is complete, job’s done.

3) You should know: Point 2

Patient data including patient info, images, cine loops and reports are safely kept in place after upgrade. Just in case, we still recommend you do backup before upgrade.

Page 5 of 27


2

UPGRADE STEP ONE – Bios Update

Please check the current bios version. Follow the steps as below. (1) Turn on DC-7 power, Startup screen is showing like below boot p icture.

(2) When progress bar is moving, before system goes to next boot picture, repeatedly press [F2] key until BIOS password key-in screen shows up.

(3) Input password 84315837.

Page 6 of 27


(4) Set BIOS parameters as follows: Use arrow keys left and r ight to select [Information] menu Use arrow key up and down to select [Version Information], p ress Enter.

Check Bios version if it shows as below: Main BIOS 06.67.12

If yes, please go to Page 11, UPGRAGE STEP TWO-CHANGE BIOS SETT INGS If current bios version is lower, i.e. Main BIOS 06.67.12, please follow the below steps to update bios to newest version: Main BIOS 06.67.12 ； Bios update requires a virus-free USB stick. For your information, all files in USB stick would be deleted, so please backup files in USB stick in advance if needed. (1) In your PC, follow the below steps to produce a bootable USB stick. File: USB_Boot.zip Location: Disk 3: USB_Boot.zip and DC-7 Bios update files _____________________________________________________________________________ Files included: HPUSBFormatter.exe Readme.txt freedos\command.com freedos\kernel.sys freedos\src\com082pl1.exe freedos\src\ke2029src.exe

Page 7 of 27

SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD. freedos\src\README _____________________________________________________________________________ Method: 1. �� .�� . (�.�. ��) 2. �� (��) �� (�.�. ��) �� . 3. �� (�� 2�� ). 4. �� (��). � ��

5. �� . 6. �� 7. �� 8. �� . �� . �� . 10. � �� .

(2) Copy the bios update files shown as below (Location: Disk 3 USB_Boot.zip and DC-7 Bios update files) to the bootable USB stick root directory.

Page 8 of 27


(3) Connect the USB stick to DC-7 USB port. Turn on DC-7 power, when appear bios boot picture (first boot image), repeatedly click F2, entering bios, password 84315837, change boot order, select the USB HDD, press “shift” and “+” ,move the bootable USB stick up to the first place, like the below pic,

Escape to “exit” page, click “save changes”

Click “Save CMOS to Flash”, and press any key to continue

Click “Exit Saving Changes” Restart. System is starting from USB stick. You will see below message.

Page 9 of 27


Press any key Automatically running

Bios update Finished.

(4) Disconnect the USB stick and restart.

Page 10 of 27


3

UPGRADE STEP TWO – change BIOS setting to boot from CD

(5) Turn on DC-7 power, put DISK 1: Windows XP disk into DVD/CD Drive disk compartment.

The whole upgrade process lasts more than half an hour. (6) Startup screen is showing like below bo ot picture.

(7) When progress bar is moving, before system goes to next boot picture, repeatedly press [F2] key until BIOS password key-in screen shows up.


Page 11 of 27


(9) Set BIOS parameters as follows: Use arrow keys left and right to select [Boot] menu Use arrow key up and down to select [Boot order], press Enter.

Use arrow key up and down to select [USB CDROM] Press and hold ‘SHIFT’ key and click ‘+’ key (plus key) to move [USB CDROM] all the way up to the first place;

Page 12 of 27


Press “ESC” key to exit. Select [Exit] menu, Use arrow key up and down to select [Save changes], click Enter.

Select “Save CMOS To Flash”, click Enter.

Press any key (within Alphanumeric keyboard area) to continue

Page 13 of 27


Select [Exit Saving Changes], click Enter.

System automatic restarts.

Page 14 of 27


4

UPGRADE STEP THREE --- Windows XP System Update

(1) System is Restarting. After the first boot picture disappears, screen blacks out till it shows “Press any key to boot from CD or DVD…” The message slips through in a very short period, approx 2 seconds. Please take chance to press any key on Alphanumeric keyboard.

(2) System is automatic loading files.

Shortly after Windows XP system booting picture disappears, a DOS window shows like below:

(3) Press any key on alphanumeric keyboard. XPE installation process lasts about 15-20 minutes. Please do not interrupt the installation.

Page 15 of 27


(4) After installation is complete, DOS message shows like below:

(5) Press any key on alphanumeric keyboard. System’s automatic restarting. (6) During starting, after the first boot picture disappears, you see the message “Press any key to boot from CD or DVD…” one more time, please do not do anything this time, otherwise, system would install Windows XP once again. (7) After this screen, you can see Windows XP system loading setup.

When you are asked to create a user account, please do not change anything; click “Next” to skip it.

Page 16 of 27


After setup is finished, system is restarting. Once again, during starting, after the first boot picture disappears, you will see the message “Press any key to boot from CD or DVD…”, please do not do anything, otherwise, system would install Windows XP once again. (8) System is now going to windows desktop.

Page 17 of 27


5

UPGRADE STEP FOUR --- Doppler Update

(1) Take out DISK 1, put DISK 2: Doppler Software disk into DVD/CD disk compartment. Or, if you had all Doppler software files copied to a virus-free USB stick, please connect it with DC-7 USB port. Choosing Back USB ports and touch-screen side USB ports are all fine. (2) If you insert the disk, after a few minutes, system is automatic running install process like below:

If you connect USB stick with Doppler software files, please double click on file “run”, then system is automatic running installation process.

Page 18 of 27


(3) The installation process lasts about 10-15 minutes. During process, you may see “finding new hardware” page, please do not do anything, they would automatic disappear.

(4) When the installation is finished, please check if there’re any failures. Software installation will recover ECG and 4D module data, as they are optional modules, in case your DC-7 doesn’t have them, you may see recover failure items for ECG or 4D module, but it’s all right. System software can still continue be running with these failure. (5) Finally, a DOS message “Do you want to delete user preset data” shows like below:

Page 19 of 27


(6) If you want to use new preset data, please input “Y”, then press “ENTER” key on alphanumeric keyboard to quit the program. We strongly recommend you this option. If you want to use the current preset data, input “N”, then press “ENTER” key on alphanumeric keyboard to quit the program. (7) Shut down Windows.

Page 20 of 27


6

UPGRADE STEP FIVE --- change BIOS setting to disable boot from CD

(1) Turn on power. When the f irst boot picture progress bar is moving, before system goes to next boot picture, repeatedly press [F2] key until BIOS password key-in screen shows up.


(3) Set BIOS parameters as follows: Use arrow keys left and right to select [Boot] menu Use arrow key up and down to select [Boot order], press Enter.

Page 21 of 27


Use arrow key up and down to select [USB CDROM] Click ‘-’ key (minus key) to move [USB CDROM] all the way down below hard disk like below “IDE 1: Hitachi HTS541680J9SA00TB”.

Press “ESC” key to exit. Select [Exit] menu, Use arrow key up and down to select [Save changes], click Enter.

Select “Save CMOS To Flash”, click Enter.

Press any key (within Alphanumeric keyboard area) to continue

Page 22 of 27


Select [Exit Saving Changes], click Enter.

System automatic restarts.

After that, system is going to ultrasound environment directly.

Page 23 of 27


7

UPGRADE STEP Six --- Change language Check F10 -> system preset -> Language

Click language drop-down list, change from “ English” to “Chinese”. Click OK. Do not click “Return”, click “System preset” again, change language from “Chinese” back to “English”. PS: this step is used to correct Windows system language setting. If you don’t it, some words in ultrasound environment would display in Chinese.

Page 24 of 27


8

UPGRADE STEP Seven --- Install keys for all application exams Check F10 -> system preset -> Option If you find all application exams are disabled, please obtain them from Mindray. Before you do it, please check the Mac address, F10 -> about

Follow the below steps to install them. Copy all the keys given by u s to a USB stick, Install the license keys for Abdomen exam application, obstetric, etc as indicated below: F10 -> System preset -> Option, Click on the option item, and click ‘install’ Please finish installing one by one.

Page 25 of 27


9

UPGRADE STEP Eight --- load preset data

(1) If you chose “N” previously, the whole upgrade procedure is done. You still use your preset data. (2) If you chose “Y” previously, please do following steps to load the default preset data. Press [F10] key  [Manage settings] menu  [restore factory] menu (on the bottom center)  Reboot to take effect.

Page 26 of 27


10 UPGRADE STEP Nine--- Calibrate touch screen 1. Press the [F10] key on the keyboard to enter setup menu; 2. Log in as the "Service", If access control function is turned off in the system preset, press “[Shift] +F6” to open the login  dialogue box; select account "Service", enter the p assword 84313841 and click OK; If access control is turned on in the system preset but no user has logged in, press  “[Shift] +F6” in the login dialogue box; select "Service", enter the pa ssword and click OK; If access control is turned on in the system preset and the system is logged in as Admin or  Emergency, click [Session Manager] icon on the lower right corner of the screen, and press “[Shift]+F6” in the login dialogue box to s how "Service" and select, enter the password and click OK. 3. Click [Maintenance] to enter maintenance interface; 4. Select the [Touch Calibrate] tab in the [Touch Screen]; 5. In the touch screen, use the pencil tip to click the crosses one by one as p er the cursor indication until it prompts that the calibration is done.

The End

Page 27 of 27

Upgrade guide

Recommend Documents