ALCATEL-LUCENT ALCATEL-LUCENT SOFTWARE INSTALLATION & FIELD INTEGRATION OF ISAM GPEC - FIXED NETWORKS February - March 2013
1
AGENDA 1. Software Installation
2. 7302 ISAM Craft Interface Connection 3. Field Integration
2
AGENDA 1. Software Installation
2. 7302 ISAM Craft Interface Connection 3. Field Integration
2
1. Software Installation
3
Introduction The 7302 ISAM products come with pre-installed software. Pre-Installed software can be upgraded to appropriate release. If there is no software installed on compact flash (CF) card of NT card, related image file can be written into the CF.
Warning: Responsibility to purchase the necessary hex editor software which will be used during the operation belongs to participant. «Winhex» software will not be supplied to participants, it is not a freeware product!
Alcatel-Lucent is not responsible of the damages which might occur during the misuse of the program.
Copying the Related Image to Compact Flash Card Copy the “image_2048000000” to CF card with hex editor (e.g. Win Hex).
Open Win Hex editor and then click on “Clone Disk” button.
Write the related image into the CF a. b. c. d.
Click on the up-right button and insert the “ image_2048000000” as a source file. Click on the down-left button, indicate the destination disk Set the “Start Sector” value to zero Click on “OK” button.
Write the related image into the CF There are two warning message before starting copying process, click on “OK” button for both warning messages.
After copying process, please see the “ ... sector(s) copied” pop-up, then click on “OK”.
2. Connecting to 7302 ISAM Console
7302 ISAM Craft Cable Connection A Craft interface port is provided on the front plate of NT card (NANT-A or NANT-E) that allows the operator to connect the NT card via craft cable directly.
7302 ISAM Craft Cable Connection Connect the RJ45 end of the craft cable to 7302 ISAM CRAFT Port on the NT card.
Connect DB-9 end of the craft cable to your PC with or without RS232 to USB converter.
Connecting to 7302 ISAM via HyperTerminal Start the HyperTerminal application on your PC and enter a connection name (e.g., “7302_ISAM”) and an icon. Then click the “OK” button.
Connecting to 7302 ISAM via HyperTerminal Select the proper COM port. You can learn your USB-Serial Com Port value from Device Manager.
Connecting to 7302 ISAM via HyperTerminal Specify the port settings and click the “OK” button
First Time Login via Craft Terminal When your connection is ready via console cable between your computer and 7302 ISAM, you should press C value. Login the 7302 ISAM with user name “isadmin” and password i$@mad- “. “
After logged in, the password should be changed for the first time; modify it to “ ANS#150”. Would you like a CLI(C) or a TL1 login(T) or TL1 normal session(N) ? [N]: login: password: Welcome to ISAM Your password is expired ! enter new password: re-enter password: The new password is accepted. leg:isadmin>#
Checking Software Version and OSWP Table leg:isadmin># ================================================================================ etsi table ================================================================================ isam-release : R4.2.02 ================================================================================
Run “show software-mgnt oswp ” command to see OSWP table leg:isadmin># ================================================================================ oswp table ================================================================================ | | | |commit index|name |availability|act-status|status -----+-------------------------------------+------------+----------+-----------1 L6GPAA42.228 enabled active committed 2 NO_OSWP empty not-active un-committed -------------------------------------------------------------------------------oswp count : 2 ================================================================================
Config Check and Clear DB System Management Configuration can be checked using the command below leg:isadmin># configure system #--------------------------------------------------echo "system" #--------------------------------------------------management host-ip-address manual: default-route exit exit #---------------------------------------------------
If necessary, configuration can be removed using the command below. When re-activation with clear db is applied, no management config is restored. leg:isadmin>#
Plug-out and Plug-in the NT card (hard-reset) and wait for the initialization
How to change root name> leg:isadmin># Prompt name can be changed using the command below configure system security operator isadmin prompt ISAM001> ISAM001>info configure system configure #-----------------------------------------------------------------------------echo "system" #-----------------------------------------------------------------------------system id ISAM_RPEC name ASAM location SouthAfrica contact-person Alcatel en-snmp-auth-trap nt-intercon-vlan 4092 internal-nw-vlan 4089 system-mac 18:80:f5:21:b8:b9/18:80:f5:21:af:b0/24 sntp .
3. Field Integration
NANT-A System Management IP & Default Route Configuration To allow remote connectivity you should configure management IP and default route address of NANT-A. leg:isadmin># leg:isadmin>configure>system>management# leg:isadmin>configure>system>management>default-route$
leg:isadmin># configure system #--------------------------------------------------echo "system" #--------------------------------------------------management host-ip-address manual: default-route exit exit #---------------------------------------------------
NANT-A Management VLAN and Network Port Configuration Default management VLAN-id is 4093. Assume that you are going to configure “network port 0”. leg:isadmin># leg:isadmin>configure>interface>shub>port>0# leg:isadmin>configure>interface>shub>port>0# leg:isadmin>#
Configuration for untagged management traffic. leg:isadmin># leg:isadmin># leg:isadmin>configure>bridge>shub>port>0#
If you need to change the management VLAN-id, both the ASAM-core as the service hub needs to know the management VLAN-id. leg:isadmin># leg:isadmin>configure>system#
NANT-A Ping the Default Gateway leg:isadmin># PING 172.29.4.1 56 data bytes 64 bytes from 172.29.4.1: icmp_seq=1 ttl=64 time<1ms. 64 bytes from 172.29.4.1: icmp_seq=2 ttl=64 time<1ms. 64 bytes from 172.29.4.1: icmp_seq=3 ttl=64 time<1ms. 64 bytes from 172.29.4.1: icmp_seq=4 ttl=64 time<1ms. 64 bytes from 172.29.4.1: icmp_seq=5 ttl=64 time<1ms. ---- 172.29.4.1 PING Statistics ---5 packets transmitted, 5 packets received, 0% packet loss round-trip min < 1ms, avg < 1ms, max < 1ms, stddev < 1ms
NANT-A SNMP Configuration To make 7302 ISAM manageable from 5520 AMS, SNMP community strings should be configured. leg:isadmin># leg:isadmin>configure>system>security>snmp>community>public>hostaddress>172.29.7.250/22$ leg:isadmin># leg:isadmin>configure>system>security>snmp>community>NETMAN>hostaddress>172.29.7.250/22$
Saving the Configuration leg:isadmin>#
NANT-D / NANT-E System Management IP & Default Route Configuration The following procedure describes how to configure IP & default route: 1. Configure selected port
2. Create/configure IES & add vp (virtual port)
For untagged port :
sap nt-a:sfp:1:0 create (NANT-D) sap nt-a:xfp:1:0 create (NANT-E)
For tagged (management VLAN Id 4093) port :
sap nt-a:sfp:1:4093 create (NANT-D) sap nt-a:xfp:1:4093 create (NANT-E)
3. Create VPLS & add relevant network port(s) 4. Add static route for connectivity (if applicable)
NANT-D / NANT-E Sample of IP & Default Route Configuration
NANT-D / NANT-E Ping the Default Gateway leg:isadmin># PING 192.168.0.2 56 data bytes 64 bytes from 192.168.0.2: icmp_seq=1 ttl=64 time<1ms. 64 bytes from 192.168.0.2: icmp_seq=2 ttl=64 time<1ms. 64 bytes from 192.168.0.2: icmp_seq=3 ttl=64 time<1ms. 64 bytes from 192.168.0.2: icmp_seq=4 ttl=64 time<1ms. 64 bytes from 192.168.0.2: icmp_seq=5 ttl=64 time<1ms. ---- 192.168.0.2 PING Statistics ---5 packets transmitted, 5 packets received, 0% packet loss round-trip min < 1ms, avg < 1ms, max < 1ms, stddev < 1ms leg:isadmin>#
NANT-D / NANT-E SNMP Configuration The SNMP configuration needs to be done for managing ISAM remotely on 5520 AMS. Host-address in the configuration for both cases should be the IP address of AMS server for security reasons. To configure SNMP: 1. Make sure ping is available. Ping
should be successful from ISAM node to 5520 AMS.
2. Login to CLI interface of ISAM node via “Telnet” or “SSH” protocols. 3. Configure the ISAM node SNMP parameter. Configure
SNMP string “public” for “nt” context Configure SNMP string “NETMAN” for “ihub” context
NANT-D / NANT-E SNMP Configuration To make 7302 ISAM manageable from 5520 AMS, SNMP community strings should be configured. leg:isadmin># leg:isadmin>configure>system>security>snmp>community>public>hostaddress>0.0.0.0/0# exit all leg:isadmin>#
High Speed Board Configuration To configure an installed ISAM board follow the procedure below: Connect to ISAM to using Console Connection or Remote Connection (SSH/Telnet) Configure Maximum link speed per GPON LT and the planned-type per cards in the system. For
NGLT-A Board 2.5 Gbps
For
FGXT-A Board 10 Gbps
leg:isadmin># one-gb twodotfive-gb ten-gb twenty-gb leg:isadmin>#
! ! ! !
enables enables enables enables
max max max max
1 Gbps lt link speed 2.5 Gbps lt link speed 10 Gbps lt link speed 20 Gbps lt link speed
View card status of ISAM leg:isadmin># ============================================================================= slot table ============================================================================= slot |actual-type|enabled|error-status |availability |restrt-cnt ---------+-----------+-------+----------------------+-------------+---------nt-a nant-e yes no-error available 0
lt:1/1/3 empty no no-error not-installed 0 lt:1/1/4 empty no no-error not-installed 0 lt:1/1/5 empty no no-error not-installed 0 lt:1/1/6 empty no no-error not-installed 0 lt:1/1/7 empty no no-error not-installed 0 lt:1/1/8 empty no no-error not-installed 0 lt:1/1/12 empty no no-error not-installed 0 lt:1/1/13 empty no no-error not-installed 0 lt:1/1/14 empty no no-error not-installed 0 lt:1/1/15 empty no no-error not-installed 0 lt:1/1/16 empty no no-error not-installed 0 lt:1/1/17 empty no no-error not-installed 0 lt:1/1/18 empty no no-error not-installed 0 lt:1/1/19 empty no no-error not-installed 0 ----------------------------------------------------------------------------slot count : 18 =============================================================================
Plan a board If the card is not configured, “no-planned-board” statement should be seen at the error-status column. Table below shows how to configure cards installed to shelf. leg:isadmin># leg:isadmin># leg:isadmin>#
Warning: NGLT Board can only be configured with NANT-D/E deployed shelf.
View card status of ISAM after planning the board After card configuration, “no-error” statement should be seen at the error-status column. leg:isadmin># =============================================================================== slot table =============================================================================== slot |actual-type|enabled|error-status |availability |restrt-cnt ---------+-----------+-------+----------------------+-------------+-----------nt-a nant-e yes no-error available 0
lt:1/1/3 empty no no-error not-installed 0 lt:1/1/4 empty no no-error not-installed 0 lt:1/1/5 empty no no-error not-installed 0 lt:1/1/6 empty no no-error not-installed 0 lt:1/1/7 empty no no-error not-installed 0 lt:1/1/8 empty no no-error not-installed 0 lt:1/1/12 empty no no-error not-installed 0 lt:1/1/13 empty no no-error not-installed 0 lt:1/1/14 empty no no-error not-installed 0 lt:1/1/15 empty no no-error not-installed 0 lt:1/1/16 empty no no-error not-installed 0 lt:1/1/17 empty no no-error not-installed 0 lt:1/1/18 empty no no-error not-installed 0 lt:1/1/19 empty no no-error not-installed 0 ------------------------------------------------------------------------------slot count : 18 ===============================================================================
NTIO Card Configuration The NTIO cards can be used different modes. Therefore, this choice must be configured via the paremeter "applique-profile" when planning the applique. When NTIO card is planned, an isam reboot (with selftest) must be performed before it takes effect. \\NANT-A leg:isadmin># \\NANT-E leg:isadmin>#
leg:isadmin>#
NTIO Card Configuration \\NANT-A leg:isadmin># ================================================================================ applique table ================================================================================ applique |actual-type|enabled|error-status |availability ---------+-----------+-------+----------------------+--------------------------iont:1/1 yes no-error available -------------------------------------------------------------------------------applique count : 1 ================================================================================ \\NANT-E leg:isadmin># ==================================================================================== applique table ==================================================================================== applique |actual-type|enabled|error-status |availability ---------+-----------+-------+----------------------+-----------------------------------------------ntio-1 yes no-error available -----------------------------------------------------------------------------------applique count : 1 ====================================================================================
Extended LT Slot Configuration Use one of the following commands to change the shelf mode: Change the mode from NTB_NTIO_SUPPORTED to NTB_NTIO_UNSUPPORTED with the following command. leg:isadmin># warning: Any successful change in shelf mode will trigger a system reboot! Info: If the command is successful, please do not do any operations until the system startup again!
leg:isadmin># ================================================================================ shelf table (detailed) ================================================================================ -------------------------------------------------------------------------------shelf -------------------------------------------------------------------------------shelf : 1/1 planned-type : nfxs-a actual-type : nfxs-a admin-status : unlock oper-status : enabled error-status : no-error availability : available shelf-mode : class : main-ethernet description : ================================================================================
Warning: Exdended LT Slot configuration is not supported on 7360 FX platforms.
Time Configuration To configure time and date settings leg:isadmin># leg:isadmin># ================================================================================ sntp table ================================================================================ operating-mode : unicast system-time : 2011-11-22:15:45:34 shub-time : 2011-11-22:15:45:34 ================================================================================
Saving Configuration After configuring the ISAM, the new configuration needs to be saved. \\NANT-A leg:isadmin># \\NANT-E leg:isadmin># Writing file to /pub/IPD/dm/config.cfg Saving configuration .... Completed. leg:isadmin>#
