View3D Gui Guide de Introduction to View3D ..................................................... ............................................................................................................. ............................................................. ..... 1 Starting Hampson-Russell Software ..................................................... ............................................................................................... .......................................... 2 Starting View3D ................................................... ....................................................... ...................................................................... ............... 4 A Brief Brief Summary of the the View3D Process ................................................. ................................. 8 Loading the Seismic and Horizon Data ................................................ .......................................... 8 Viewing the Data .................................................. ....................................................... .................................................................... ............. 11 Scaling the Plot ..................................................... ............................................................................................................ .................................................................... ............. 12 Saving the Viewing Parameters ........................................................ ................................................................................................ ........................................ 14 Stopping This Tutorial ................................................... ........................................................ ........................................................... ... 15 Adding Slices .................................................. ........................................................ .............................................................................. ...................... 15 Displaying Attribute Values............................................... Values....................................................................................................... ........................................................... ... 18 Changing Color Color Keys For Color Plots .................................................. ........................................ 19 Showing Traces and Color Plots Together ................................................ ............................... 22 Top, Side and Other Points of View ..................................................... ............................................................................................. ........................................ 22 Special Zoom Views ...................................................... .............................................................................................................. ........................................................... ... 25 Birds' Eye View ................................................ ....................................................... .................................................................... ............. 25 Magnifying Glass Zoom ..................................................... ....................................................................................................... .................................................. 25 Oblique Slices, Fences and Probes ................................................... ........................................ 26 Oblique Slices (Rotated Slices).............................................................. ............................... 27 Making Fences .................................................. ....................................................... .................................................................... ............. 29 Probes...................................................... Probes .............................................................................................................. .............................................................................. ...................... 30 Showing Well Log Data.............................................................. Data....... ......................................................................................................... .................................................. 34 Selecting Which Wells to View .................................................... ............................................................................................ ........................................ 38 Emphasing Value Ranges and Setting Transparency: Visual Control.......................................... 39 Removing Data From View3D ................................................... .................................................. 43 Loading Data Slices as Horizons ................................................ .................................................. 43
VIEW3D 1
GUIDE TO TO View3D View 3D Introduct ion t o View3D View3D View3D is a program used to view wellbore paths, well data, seismic data and attribute data as a
three dimensional volume. The general objective is to better visualize, illustrate and spatially analyze the data from HRS programs. This tutorial takes you through the most important options and features of View3D.
The data set for this tutorial consists c onsists of: A SEGY file, seismic.vol, which is a 3D post-stack data set. An attribute volume, scaled_porosity.vol , which is a 3D post-stack data set. 7 wells. Each well contains a sonic log (p wave), density density log, porosity log and a checkshot file. A horizon file, Target_hrz. Two data slices: seismic target and and scaled porosity, positioned at the same place as the horizon file. • • •
• •
January 2007
2 VIEW3D
Starting Starting Hampson Hampson -Russell -Russell Software The first step is to start the GEOVIEW program. GEOVIEW is the application manager that acts as a launch pad for other Hampson-Russell Hampson-Russell programs. If you are unfamiliar with with the use of GEOVIEW, please refer to the Guide to GEOVIEW and eLOG documentation. On a Unix workstation, go to a command window and typing: GEOVIEW
On a PC, click the Start button button and select the GEOVIEW option on the Programs / HRS applications menu. Opened Database Lis t, When you first launch GEOVIEW, the first window that yo u see is the Opened which displays your recently recently used databases. A database is identified identified by the extension wdb. For this tutorial, a database has already been created for you. To load this database for the first time, click Open to bring up the Directory Chooser .
Click the view3D folder of the HRS/data directory to bring up a list of databases in that folder. L is t and click OK . Click the View3D.wdb item in the Av ail abl e Lis
January 2007
VIEW3D 3
GEOVIEW W Well Exp lor er window The GEOVIE window appears, showing the seven wells within this database. For more on this window, see the GEOVIEW section of the Installation GEOVIEW and eLOG Guide. For now, click the X at the top right to close the window.
January 2007
4 VIEW3D
Starting View3D Now that the database has been opened in GEOVIEW, we are ready to start the View3D program. To do this, click the View3D button on the GEOVIEW window.
The following window now appears:
January 2007
VIEW3D 5
Note that you cannot start a new project in View3D. The program is intended as an add-on to other HRS programs, and not as a stand-alone program. Therefore, you would need to open a project first created in another HRS program. You can use View3D to view any project created through these and other HRS programs. Fortunately, we have provided a project for this tutorial. Check the Open Existing Project button and click OK to bring up the Directory Chooser . Click the View3DE_Guide folder in the View3D directory to show projects in the Av ail abl e Li st . Click the View3D_sand.prj project in the Av ail abl e Li st and click OK .
If a message appears telling you that the pathway to the project has changed, select Switch .
January 2007
6 VIEW3D
The View3D Data and Display windows now appear: The Data window is used to select what data to load and unload data from the display. It will appear like this:
January 2007
VIEW3D 7
Note that the wells may be automatically selected for loading, but that nothing else is. The Project Loaded column shows the available data in the selected project. If data were missing from this list, you need to return to the original HRS program that created the project and then load that data through that program. Then save that program. Then you would return to View3D to display the complete data set. The View3D Data tab shows what data has been selected and what has already been loaded. The wells are automatically assumed selected for loading but the other data is not yet selected. The History tab lists the operations to this time that had loaded or unloaded data. The Filter section section lets you filter the list of wells. Click the X at the upper left of the Filter box box to hide that section. The Plot button loads (or unloads) the selected items into View3D. What has been loaded can now be viewed using the Display window features. The Display Window shows the plotted data and controls its display. Because no data has been selected and plotted yet, the Display Window is black.
January 2007
8 VIEW3D
A B rief ri ef Summ Su mm ary of the th e View3D View 3D Proc ess •
• • • • •
In the left side of the Data window, select the data to be plotted. In the right side of that window, set the details for loading. Start the Plot process, activating the Display window. Zoom the Display window to show the desired area. Select the Display mode for the Display window and select what planes to show. Set the horizon, well and seismic display parameters as needed. Adjust the view as needed, creating new slices as required.
The geological play this tutorial handles is the same handled in the EMERGE tutorial and guide. It is a channel sand with porosity that can be predicted from seismic data.
Loading the Seismi Seismi c and Horizon Data On the Data window, double-click the horizon Target_hrz in the Horizon folder of the Project Loaded section and the volume seismic.vol in the Post-stack folder. They will now appear on the right side of the Data window, with the status "to be loaded " as shown below. Select the View3D Data tab in the top right of the window (it should be selected by default). In the Well Data section, scroll up if required and select the Density and Porosity checkboxes.
January 2007
VIEW3D 9
Click once anywhere in the seismic.vol line. Move to the D/T Start column on that line (you may need to use the horizontal scroll bar to reach this column). Then click once in the D/T Start field for seismic.vol. When a cursor appears in that field, change the value from "2" to "800" and press . We do this so that the plot will not extend above 800 milliseconds TWT. Otherwise, the plot would have extended up to 2 milliseconds and be too tall and awkward to view. See below:
Note: Whenever you edit something in this table, you must press before exiting that field to keep the edit. If the wells are not automatically selected for plotting, click each well in the Well folder of the Project Loaded section. Click Plot . The selected data now appears in the Display window, while " Loaded " appears in the Status columns of the Data window.
January 2007
10 VIEW3D
January 2007
VIEW3D 11
Viewing the Data In the following figure, note that the outline of the entire volume and wellbore lengths are shown: this is the default, or "Home" view for the data, and you can return to this view by pressing the Home key on the left vertical toolbar.
If the window is too short to show the entire toolbar on the left, a scroll icon will let you display the rest of the toolbar. Note also that the zone of interest, the part with the horizon, is dwarfed by the spread of data. The actual color choices for the well data, Seismic and Horizon Color Keys will depend on what was last used in the program. We will show how to change them later.
January 2007
12 VIEW3D
Scaling Scaling the Plot Your horizon may not appear exactly as shown above, and this is because the scaling may be different. If the Time axis scale (Z) is too exaggerated, the horizon may look unreasonable. If your Z scaling is too small, the horizon may look featureless. From the Options menu, select Scaling to bring up the Scaling window. Ensure that these values are entered: X=1 Y=1 Z=0.5 If not, then correct the values and click OK .
If your plot disappears, then click the Home button on the left toolbar. Your plot will reappear with the correct scale. You may need to click the double arrows at the bottom of the toolbar to expand it, as shown below.
As a check, we will display a north arrow. From the Options menu, select Show North Arrow to see a yellow arrow at the top of the plot (see below).
January 2007
VIEW3D 13
The entire volume is displayed with south facing upwards, contrary to what we would normally expect, and we should keep that in mind. Reselect Show North Arrow to hide that arrow. We will now zoom into the zone of interest, using the mouse, as shown below: From above the 1010 value on the left , press the middle mouse button down and drag it to about the 1125 value on the right (see (see below).
January 2007
14 VIEW3D
When you release the mouse button, the display will be zoomed in. Note the well bores, well tops and the horizon. You may need to resize the edges of the window to see the time scales at the left and right.
You can use the middle mouse button to: SHIFT + Middle Mouse Button Shift the display around the screen: SHIFT + CTRL + Middle Mouse Button Rotate the display around a point: CTRL + Zoom and unzoom: Middle Mouse Button , hold and drag as previously shown Notice that there is no seismic data displayed, even though the respective color key is shown. This is because we have not selected anything at the bottom of the window yet, as shown below.
Saving the Viewing Parameters This will let you save your you r work and retrieve it again, which is very useful if you must interrupt this tutorial. From the Main menu, select File>Set Scene 1. Now, when you restart this tutorial, you will Data Windo w and click Plot . When the Display window need to reselect everything on the Data
January 2007
VIEW3D 15
appears, all you need to do is select File>Load Scene 1, or click the Recall Scene 1 button from the left-hand toolbar.
Stopping This Tutorial First, save your scene, as described above. Close the Data window (not the Display window). Both windows close and the Visual3D session ends when you close the Data window.
Addi Ad ding ng Slices Sli ces Select Slice mode from the bottom left menu of the Display window, if it is not already selected.
Click the X box to display the X-axis slice as shown below:
This X slice above shows the porosity values that we have loaded as an attribute. It also partially obscures the horizon, the wells and well top information (hence the clipped well top labels, which are easier to see on the screen than on a gray-scale diagram). To move this slice, ensure Creation Mode toolbar is selected. This toolbar that the Slide Slices Mode button of the Slice Creation is at the upper right of the Display window.
January 2007
16 VIEW3D
Then click the slice with the left mouse button to select it. The slice now has a red border with the edges of the volume and with any intersecting horizons or slices.
Seismi c> Show Color Map Map and We have also hidden the color keys, by selecting Seismi Horizon>Show Color Map Map to turn the Color Map toggles off.
Now drag the X slice towards the rear (to the left) until it is at the edge of the volume, then release the left mouse button to place it as shown below:
January 2007
VIEW3D 17
Repeat these steps for the Y slice, checking its box at the bottom left and then moving it to the right and back. Repeat these steps for the Z slice, checking its box at the bottom left and then moving it to about 1100 ms, to get the display below:
January 2007
18 VIEW3D
Displaying Att ribut e Values Values For View3D, attributes and seismic data are treated the same except that only seismic data can be represented by wiggle traces. View3D can only display one "attribute" volume and one "seismic" volume at the same time. However, you can select what you want as seismic and attribute. We recommend that "seismic" should be reserved for actual seismic data, while "attribute" should be reserved for values calculated from the seismic data, such as inversions generated through the STRATA program or petrophysical parameters generated through the EMERGE program. Double-click scaled_porosity.vol in the Post-stack folder of the Project Loaded section of the Data window to display that attribute volume in the View3D Data section to the right. as Attrib ute box for the scaled_porosity.vol data, but uncheck the load as Now check the load as Seismic box.
Note that this volume already has a D/T Start value of "800", but it does not matter for the display if this volume had a different value, since the display's dimensions are set by the first volume loaded (hence by the seismic.vol volume). One useful function is to place the mouse over volumes in the View3D Data table. Then a popup appears, giving the basic geometry for that data, as shown below (for the seismic.vol line):
There are also right-click pop-up menus in the Data window that are useful. See the online help for more on these menus.
January 2007
VIEW3D 19
Click Plot . The Display window will now show the attribute (porosity) as a color scale and the Attribute color key will be displayed (you can turn this off through the At tr ib ut e menu in the same way as done for the other color keys).
Changing Changing Color Keys For Color Plots We will now change the attribute color key to emphasize the higher porosity values. The default Color Map is Rainbow, as used above. Select Color Map Map from the At tr ib ut e menu to bring up the ColorMap Setti Setti ngs window.
January 2007
20 VIEW3D
Scroll down to the Lightning Color Map and select it.
Click OK to apply the change and close the Colormap Settings window.
January 2007
VIEW3D 21
Now the high porosity values are red or yellow and are easier to notice (at least on the screen, which should not be monochromatic like this book) while the lower porosity values, in which we are not interested, are in similar shades of green and easily ignored. If the Upper and and Lower values values in the Color Mapping section do not approximately match the Minimum and Maximum values respectively in the Data Range section, then change them to be close (e.g., using "0" for the Lower and and "0.16" for the Upper values). values).
To further demonstrate the porosity value, while in Slide mode the horizon to see how the porosity value changes.
, slide the Z slice up through
Then move the Z slice back to its original position at about 1100 ms.
January 2007
22 VIEW3D
Showing Traces Traces and Color Plots Together Together We will now show the seismic data in a form that is not hidden by the scaled porosity colors, essentially co-rendering the two sets of data. Select Seismic>Wiggle from the Display menu. The seismic will now be displayed as wiggle traces on top of the attribute colors. To return the seismic to its color display, reselect this menu option to turn it off.
Top, Side and Other Points of View In the Well menu, uncheck the options An no tat io n (well and top names) and Top s (disks showing where the tops are on the well bore) so only the well bores are shown. In the At tr ib ut e Map option to hide the color key. At the bottom of the window, menu, uncheck the Show Color Map uncheck the Y and Z checkboxes, so only the X plane is left. These steps will declutter the view.
January 2007
VIEW3D 23
Now click the Front View button that below:
on the left of the Display window to change the display to
Use the Undo button or the BACKSPACE key on the keyboard to return to the previous view. Now click the Top View button .
January 2007
24 VIEW3D
Again, click the Undo button to return to the original view. Press PAGEUP or click the three times to get the following view. Zoom In button
Again, click the Undo button three times
to return to the original view.
You can also move the view in the window by the arrow buttons or using SHIFT and the keyboard arrow keys. Note that the arrows act as if you are moving the display (as if it were a paper printout), and not as as if you were moving your viewpoint (as in video games).
January 2007
VIEW3D 25
Special Zoom Views Birds' Eye View Press SHIFT-HOME on the keyboard to use this feature. A view of the entire volume will be displayed in the upper right corner. This view will match the orientation of the current view. Press SHIFT-HOME on the keyboard again to close the birds' eye view.
Magnifying Glass Zoom Press M (or m ) on the keyboard to use this feature. Note: The Display Window must be active for this to work. wo rk. If you are doing this tutorial by using a pdf file on a screen, you may have that screen active when you click M and then nothing happens. In that case, click on the Display Window to activate it and reclick M. A square appears in the middle of the view, magnifying the zone behind it. This magnifying glass now moves with the mouse. You can still use the middle mouse button for zooming or the left button for moving slices while this feature is up. You can also make this square wider or smaller with CTRL-PAGEUP and CTRL-PAGEDOWN. Press M again to turn it off.
January 2007
26 VIEW3D
Oblique Slices, Fences and Probes Now we will show alternative ways to display parts of the volume. First, uncheck the X checkbox to remove that plane (clearing the display except for the horizon) and click Home once so the top of the volume is visible. Then click the Zoom In button twice. If the top of the volume is off the screen, use the Move Down button to move it into view.
On the upper right side of the window, we have the Slice Mode buttons.
January 2007
VIEW3D 27
Oblique Slices (Rotated Slices) An oblique or rotated slice is a slice that does not parallel the X or Y axes, but is perpendicular to the Z plane. In other words, it it is as if you took an X (or Y) slice slice and rotated it. Remember that you must be able to view the top of the volume to create these slices. Click the Create a Rotated Slice icon . Then click down on one upper edge of the volume (and do not release the button) and drag the mouse toward you and to the left. This is the direction perpendicular to to the line you want. A line with an attached vector indicator now appears. The end of the vector is is controlled by the mouse.
With the left button still pressed, you can use the mouse to move the vector and therefore the slice.
January 2007
28 VIEW3D
Release the mouse button to create the slice.
If you click on a rotated slice or an edge, another slice will be created at that point and you can position it as long as the mouse button is held down. To stop making such slices when you click on the Display window, click the Delete Slice icon (the box with the X, ) and select the new slice to remove it. Then select Slide Slice leave the Delete mode.
January 2007
to
VIEW3D 29
Making Fences A fence is a series of slices connected end-to-end, resembling a fence (of course). They can be very useful to follow channels, bars or reefs, or to outline a property of land. To create a fence, click the Fence icon. Then click the front left side to start the fence (you must click on the top plane, not on the side).
Click the end of that fence panel on the front front right side. Now click in a direction to the upper right. Click further right right and then click to to the lower right. right. See below.
Then click the Slide icon to leave Fence mode and therefore finish that fence. In other words, you enter Fence mode, click the corners of each fence section and then exit Fence mode to create a fence. Once you have created a fence, you can move its segments around in Slide mode by dragging the edges or corners. In the following example, the fence created above was moved to match the target channel. Note how it also emphasizes the horizon structure.
January 2007
30 VIEW3D
Delete Slic e icon (the box with the X, Now click the Delete ) and select one part of the fence to remove the entire fence. Remember to then select Slide, so you do not stay in Delete mode. Probes
A probe is an orthogonal shape that shows the attribute or seismic in a different way than slices. While slices must extend the entire height of the volume, probes can be limited just to an area of interest, making them ideal for screen captures. You can also create inside angles (which resembles "steps" in the probe). Since we do not need the entire volume for probes, click the Zoom In button twice. If necessary, click the Move Up button or Move Down button until the Target_hrz horizon is in the middle of the display. From the Probe menu, select Ad d . The initial orthogonal shape is added automatically.
Now select Trim Volume from the Probe menu to bring up that window. Select the Xline tab. Type "20" (or slice the slider to that value) for the Start X value and press , and type "50" for the End X value and press . The Display window will show the change in the shape.
January 2007
VIEW3D 31
Select the Inline tab and enter "40" for the Start , then press and "60" for the End , then press .
Then select the Depth tab and, instead of typing values, we will use the slider. Slide the Start slider to " 1000" for the Start Depth , and slide the End slider to " 1100" for the End Depth . You will not need need to press . Click Close.
January 2007
32 VIEW3D
The display will now show a block-like "probe".
Now we will add a corner reentrant. Click precisely on the foremost upper corner. The probe now has a cut-in section.
January 2007
VIEW3D 33
Click the rear right edge of this reentrant and slide it downwards towards the horizon.
Delete Current or Delete Delete Al l from the Probe menu to remove the When you are finished, select Delete probe display.
January 2007
34 VIEW3D
Showing Well Well Log Data Data First zoom in three times with the Zoom In button and use the Move Down button needed to move the horizon downward to get a display like that below.
In the Well menu, turn the An no tat io n and Tops back on. Select Well>Symbol Well>Symbol Size and ensure that the values are set as below: Top Disk = "3" Thickness = "0.5" Wellbore = "2"
January 2007
as
VIEW3D 35
If they are not these values, then correct them and click OK. Otherwise, click OK or Close to close this window. The Top Disk is the marker that indicates a top on the wellbore. The Thickness value refers to the thickness of the top disks. The Well Well Bor e refers to the thickness of the actual hole outline in the display. Select Curve Display from the Well menu to bring up the Well Log Curve Display Dialog . Note that the TWT curve is always included as a curve.
January 2007
36 VIEW3D
Selectio n table and click >>Center . Select Porosity in the Curve Selectio
Now select the >>Center button in the Curve Style section. Enter the following parameters, so >>Center button the center porosity plot is easier to see: Cylinder Radius = "0.5". Scale = "2". Variable Radius selected.
January 2007
VIEW3D 37
Keep the other parameters the same. Click OK to close the Curve Display Dialog . Below is the result. Note how the radius changes to match the porosity values.
January 2007
38 VIEW3D
Selecting Which Wells to View Well Lo g Visual Dialog . In the Original From the Well menu, select Visual to bring up the Well column, uncheck all the Visible checkboxes except 16-08 16-08 and click Ap pl y .
Now only the 16-08 well is displayed. Click Close.
January 2007
VIEW3D 39
Emphasing Value Ranges Ranges and Setting Transparency: Transparency: Visual Control Check the X and Y checkboxes at the bottom of the Display window to show those slices. Position them once again at the back of the volume (they should be there automatically if you have not moved them). Select At tr ib ut e>Vis ual to bring up the Visual Control window for the Scaled Porosity attribute.
Uncheck the Freehand box and check the Linear box. box. Click on the middle red dot at the left side of the upper box. Then drag this toward the right, bringing a vertical line along, to about 3/4 over.
January 2007
40 VIEW3D
What this means is that all the values value s whose colors fit under the the now dark section will not be be displayed on the plot. Therefore, only the high porosity areas will be colored. The low porosity values will not appear. Also, the underlying seismic data will be easier to see. Click OK .
In the Seismic menu, select Visual to bring up a similar window. This time, do not uncheck the Freehand checkbox. Now draw a curve from the lower left to the upper right, such as below. Click Ap pl y .
January 2007
VIEW3D 41
To avoid confusing dark peaks with deleted values (where the black background shows through), Visual Control window to bring up the Color Map Settin Settin gs click the Color button button on the Visual window. Settin gs window. Select Rainbow (instead of Gray Scale). Click OK to remove the Color Map Settin Visual Control window to get the view below. The Rainbow color map has Click Ap pl y on the Visual no black in it, so black then means "no data shown".
Close the Visual window. For the Display mode, now select Volume instead of Slice.
The entire seismic and attribute volumes are now displayed.
January 2007
42 VIEW3D
Now, from the Seismic menu, select Hide to remove the seismic data from the display. Now only the attribute data (i.e., higher porosity) is shown.
January 2007
VIEW3D 43
Remov Remov ing Data Data From View3D At the bottom left of the Display window, reselect Slice instead of Volume for the Display mode. Hide the displayed well through the Well>Visual option by unchecking the Visible box in the Original column, as done before. Return to the Data window and uncheck the scaled_porosity.vol box in the Selected Selected Volu mes table and click Plot .
This will unload the attribute plot, leaving only the seismic, well and horizon data. We could have instead hidden the attribute plot without removing it by selecting At tr ib ut e> Hid e.
Loading Data Slices as Horizons Now we will load a Data Slice based on the Target_hrz horizon. In the Data Slice section of the Project Loaded column in the Data window, there are two data slices. The slice seismic target is just a sparser-sampled version of the Target_hrz horizon, and we will not use it. It, however, was used in EMERGE to create another slice, the scaled_porosity slice. This slice will display porosity calculated by the EMERGE program. Double-click it to place it in the Horizon Group Data with the status " To Be Loaded ". ". Then click Plot .
January 2007
44 VIEW3D
The Display window will show the same amplitude a mplitude surface as Target_hrz, but as the sampling rate was lower, it is not as smoothed as the first horizon we used. The color plot will now represent scaled porosity, not two-way time. In this display, we have turned the Horizon Color Key display back on through Horizon>Show Color Map.
Note that blue and violet represent moderate porosity and yellow and red represent insufficient porosity. Note also that you can select which horizon to show by using the Horizon Group dropdown menu at the top of the window. We will stay with with scaled porosity.
January 2007
VIEW3D 45
Now select Horizon>Visual to open the Visual window for the scaled_porosity data slice. Click the Wire Frame check box in the Show section.
Then click Ap pl y .
The wire frame matches the TWT data and shows the effect of the sampling rate. By the way, this is a good surface to try the Magnifying Glass view we talked about earlier (as brought up by the M key). Uncheck Wire Frame and check the Contour box. box.
January 2007
46 VIEW3D
Then click Ap pl y .
These contours reflect the TWT structure. When you have finished, close the window. Then close the Data window (not the Display window). Both windows close and the Visual3D session ends when you close the Data window. This concludes the Visual3D tutorial.
January 2007
