Urban Heat Island and Mitigation Strategies at City and Building

Send Orders of of Reprints at bspsaif@emir [email protected] ates.net.ae Advances in the Development of Cool Materials for the Built Environment, Environment , 2013 , 3-32 3

CHAPTER 1 Urban Heat Island and Mitigation Strategies at City and Building Level *

Nyuk Hien Wong and Steve Kardinal Jusuf

Department of Building, National University of Singapore, 4 Architecture Drive 117566, Singapore Abstract: Extensive urbanization has resulted to economic, social, energy & environmental challenges. The global population increase led to an increasing demand for housing. Natural land has been replaced with artificial surfaces in most cities around the world with undesirable thermal effects. This, together with industrialization growth, has caused a deterioration of the urban environment. Urban heat island (UHI) phenomenon has become a common problem in many major cities worldwide. Several factors influence the urban heat island phenomenon, such as the continuous reduction of green spaces, the changes of wind velocity due to high buildings’ density, the anthropogenic heat release and the alteration of surfaces’ albedo. The aforementioned factors lead to overheating problems in cities due to the absorption of solar radiation by the various surfaces and buildings. Hence, urban climate is one of the most important elements of urban physical environment, which is often ignored in urban planning. To design a sustainable city, it is necessary to take into account the climatic conditions holistically and strategically during the planning process. Since the 1970s, German researchers have developed the concept of urban climate map (UC-Map) that has a strong focus on applied urban climatology. UC-Map is an appropriate tool for translating climatic phenomena and problems into 2-D images including symbols for land use and spatial information suitable for the urban planner. Therefore this map is a useful tool for urban planners, architects and governors in order for them to understand more accurately and evaluate the effects of urban climatic issues on decision-making and environmental control. At the micro-climate level, several UHI mitigations can be implemented to reduce the UHI severity. First is greenery. The benefits of greenery to the built environment have been widely investigated. Greenery dissipates the incoming solar radiation on the building structures through its effective shading; it reduces longwave radiation exchange between buildings due to the low surface temperatures created by plants’ shading; it reduces the ambient air temperature through evapotranspiration. evapotranspiration. The role of building’s materials, mainly determined by their optical and thermal characteristics, is crucial in reducing the thermal and solar hear gains, in the urban environment. The so-called ‘cool’ materials, characterized by high reflectivity and high emissivity, can improve the thermal conditions in cities by lowering the surface temperatures that affect the thermal exchanges with the surrounding air. Urban *Address correspondence to Nyuk Hien Wong: Department of Building, National University of Singapore, 4 Architecture Drive, Singapore 117566; Tel: +65-65163423; Fax: +65-67755502; E-mail: [email protected] Dionysia-Denia Dionysia-Denia Kolokotsa, Mattheos Santamouris and Hashem Akbari (Eds) All rights reserved-© 2013 Bentham Science Publishers

4 Cool Materials for the Built Environment Environmen t

Wong and Jusuf

ventilation is another important strategy of UHI mitigation. It is important to und erstand the nature of air flow regimes within urban canyons in order to make further progress in describing the complex interactions between mesoscale forces and the built environment that create the urban boundary layer.

Keywords: Urban heat island, mitigation strategies, urban climatic map, urban greenery, urban ventilation, cool materials. DEFINITION OF URBAN HEAT ISLAND

The world has experienced an unprecedented urban growth in the latest centuries. In 1800, only 3% of the world’s population lived in urban areas. This percentage reached 14% and 47% in 1900 and 2000 respectively. In 2008, it was the first time in history where more than half of the world’s population was living in the urban areas. Moreover in 2003, United Nations estimated that by the year 2030, up to 5 billion billion people people will will be living living in urban urban areas, areas, which which corresponds corresponds to 61% of the world's world's population population [1]. Extensive urbanization has resulted in economic, social, energy & environmental challenges. The trend in global population increase leads to an increase in housing demand. Natural land has been replaced by artificial surfaces in most cities around the world with undesirable thermal effects. This issue, together with industrialization growth, has caused a considerable deterioration of the urban environment. Buildings in cities influence the urban c limate in many ways [2]: 1.

Softscape (trees, grass and soil) is replaced by hard surfaces (asphalt and concrete);

2.

The rounded, soft shapes of trees and bushes are replace by blocky, angular buildings;

3.

Anthropogenic heat from the buildings, air conditioning systems and automobiles is released;

4.

Surface infiltration is prevented due to efficient disposal of rain water in drains, sewers and gutters;

5.

Contaminants that create an unpleasant urban atmosphere due to the chemical reactions are emitted.

Urban Heat Island and Mitigation Strategies at City

Cool Materials for the Built Environment

5

The aforementioned factors influence the amount of incoming and outgoing radiation and also affect the local wind speeds [3]. Their effects on local climate, especially on environmental temperature and ventilation, are very critical. Moreover they alter the radiative, thermal, moisture and aerodynamic properties of the environment [4], causing heat concentration in urban areas compared to its neighboring rural areas. This phenomenon is called the urban heat island (UHI) effect (see Fig. 1).UHI has become a common problem in major cities worldwide while the temperature difference between urban and rural areas can be more than 10K (Table 1).

Figure 1: Typical urban heat island profile (Source: Wong and Chen, 2009). Table 1: UHI intensity in several countries around the world City

Intensity (K)

Shanghai, China [5]

Up to 8.4

Tokyo, Japan [6]

3-8

Kuala Lumpur, Malaysia [7]

4-6.5

Singapore [8]

4

Newark, USA [9]

3

London, UK [10]

8 (max)

Lodz, Poland [11]

12 (max)


Wong and Jusuf

The severity of the UHI effect is influenced by some important factors [12-14]: 1.

Canyon geometry: Urban canyons work as traps that decrease the loss of both short-wave and long-wave radiation. This is attributed to the complex exchange between buildings and the skyline screening. Urban canyons also decrease the effective albedo of the overall area due to multiple reflections of short-wave radiation by the canyon surfaces.

2.

Building materials: Materials, such as concrete and brick, have large heat capacity and more sensible heat can be stored during daytime. The stored heat is then released back to the environment at night.

3.

Greenhouse effect: The polluted urban atmosphere traps the longwave radiation that is emitted by the ground to the sky.

4.

Anthropogenic heat source is generated by the industrial combustion, traffic, air-conditioners and other human activities.

5.

Evaporative cooling: Vegetation and water can mitigate the UHI effect since more incoming heat can be transformed into latent heat rather than sensible heat. Unfortunately, the lack of greenery in cities deteriorates the UHI effect.

6.

Urban ventilation: Wind is able to remove heat by turbulent and convective transfer. However, such heat loss from urban streets is reduced due to the obstruction of wind flow by the urban settings.

The UHI phenomenon is exacerbated by human energy release overheating and by increasing demand of air conditioning, which leads to further heating and CO2 release [15]. Simulation studies have shown that the possible increase in peak cooling electricity load due to UHI could range from 0.5 to 3% for each 1K temperature increase [16]. Meanwhile, another study in Singapore shows that 1K reduction of urban air temperature reduces the energy consumption for cooling by 5% [17]. Many studies have been conducted around the world to mitigate the UHI in the cities. This chapter discusses several UHI mitigation measures at the city, estate and building level.



7

MITIGATION STRATEGIES Urban Climatic Map at City Level

Countries need to develop their cities to stimulate economic growth and promote their national development. Therefore the development of cities compared to the various neighborhood towns and villages attracts more inhabitants, leading to an aggravated need to further urban expansion and development. Due to climate change, there is a vision to develop cities to be more sustainable and healthy for their inhabitants. Urban climate, one of the elements of urban physical environment, has gained its momentum as an important aspect of the urban planning process together with economic and social aspects. Several studies acknowledged the influence of urban forms towards urban thermal comfort [1820], urban temperature [21, 22] and urban heat island intensity [23]. Climate is an important factor of the built environment and all studies regarding urban climatic conditions are focusing on the improvement of the local climatic conditions with the simultaneous reduction of the negative microclimate effects. Two different difficulties appear in a climatic study at local level. Firstly, there is no suitable meteorological data that are available in local level since the usual meteorological measuring grid is too wide. Secondly, there is only a little or no time for the planners to make decisions and so is the available time for the meteorological investigation [24]. Germany is one of the leading countries in urban climate research. The first urban th climatic study was conducted in Berlin as early as in the end of 19 century and was used by several methodologies in the later studies such as thermal imaging, temporary weather station, car transverses, vertical soundings that led to the urban climatic map (UC-Map) in the early 80s [25]. Among the various methods, UC-Map is found very useful for urban planning purposes since it integrates the urban climatic factors and urban planning considerations. Before the development of the UC-Map methodology, the integration of urban planning and meteorology was a problem in many cities, due to the different domains and aspects of knowledge. Meteorologists do not know the planning requirements that should be considered in the urban microclimatic study, while urban planners do not understand the type of climatic data that should


Wong and Jusuf

be provided for their planning purposes [26]. As an information and evaluation tool, the UC-Map has two components, the Urban Climatic Analysis Map (UCAnMap) and the Urban Climatic Recommendation Map (UC-ReMap). The UC An-Map compiles the meteorological data, land use data, building footprint information, topography and vegetation information. The influence of these data on thermal load and thermal comfort are analyzed and classified spatially into several categories [27]. The UC-AnMap is also called “climatope map” and “synthetic climate function map”, as it represents distinct local climatic conditions and defines the climatopes. Climatopes are geographic areas in the urban space that have similar microclimatic characteristics and similar relative significance towards their surroundings. Moreover the specific tool operates on a spatial scale of several dozens to hundreds meters. The characteristics are primarily distinguished by the daily thermal variation, the vertical roughness, the topographical conditions or exposure and more importantly by the type of materials [28].

Figure 2: Workflow of UC-AnMap development for Hong Kong (Source: CUHK, 2008).

In developing a city, planners are dealing with land-use changes that usually alter the aforementioned urban characteristics and subsequently create new microclimatic conditions. The modification of roughness parameter changes the



9

urban ventilation. An increase of roughness usually limits the air exchange rates leading to an increase of the heat generated by the city. Moreover the pollutants emitted by the near-surface sources are insufficiently dispersed. This phenomenon causes critical environmental impacts to the inhabitants. The effects of inadequate ventilation are critical during periods of extremely low prevailing winds and high radiation [29]. The interaction between urban structures and climate becomes more prominent when the city is not located in a flat terrain. The urban ventilation or wind path within the city changes according to the topographic condition. Therefore, it is not only the land use and the urban structures considered in the UC-AnMap, but also the topography and its influence on the urban and rural ventilation. Fig. 2 depicts the workflow and data required to develop UC-AnMap for the urban climatic map of Hong Kong as an illustration.

Figure 3: UC-ReMap city of Stuttgart (Source: Ministry of Economy Baden-Wuerttemberg, 2008).


Wong and Jusuf

Urban Climatic Recommendation Map (UC-ReMap) targets to the planning procedure. procedure. It provides provides strategic strategic and city planning planning guidelines guidelines to improve improve the microclimatic conditions based on the UC-AnMap and practical constraints. Similar climatopes obtained from UC-AnMap are grouped into classification zones, where each zone is represented in different colors and has specific planning guidelines, so that the urban climatic conditions are not worsened. Hence, the collaboration between between the urban climatolog climatologist ist and the urban planners planners is very important important in the development of the UC-ReMap from the UC-AnMap [30]. The recommendation map can be in a form of general guidelines for urban planners. For example the Stuttgart climatic map includes a transformation of green spaces and vegetation to preserve preserve and reclaim reclaim natural vegetation in order to improve improve ventilati ventilation, on, reduce the release of air pollutants and support fresh air provision (Fig. 3) [31]. The recommendation map may also be in a form of more rigid guidelines. For example the Kassel climatic map includes guidelines on the building coverage, the spacing between between buildings buildings and their heights heights as well as the percentage percentage of greenery [32]. The implementation of the UC-ReMap involves not only the local government but also the private sectors, such as industries and businesses. The scale of the UC-Map is 1:100000 for regional analysis and 1:5000 for district analysis. It provides an overall analysis, in which, microclimatic study can be selected and conducted. Urban Climatic Map at Estate Level

Urban climatic map at the estate level provides an analysis for more detailed climatic conditions, i.e. urban i.e. urban air temperature, compared to urban climatic map at city level and it usually has the scale of 1:5000 to 1:100000 with the resolution of 100m grid. Known as temperature map, its methodology was developed based on the fact that air temperature in urban areas is closely related to land uses [33], which physically are related to the urban morphology characteristics, such as: sky view factor [34-38], greenery condition [39, 40], thermal mass of the built environment [41, 42] and building materials [43-45]. Daily minimum (Tmin), average (Tavg) and maximum (Tmax) temperatures of a specific location are calculated as the result of temperature deviation from the temperature measured at a meteorological station nearby. The deviation is mainly



11

due to the urban morphological characteristics, i.e. i.e. building, pavement and greenery, within the radius of 50 meters. The independent variables for the models can be categorized into: 1.

Climatic predictors. Those are the daily minimum (Ref T min), the average (Ref Tavg) and maximum (Ref Tmax) temperatures at a reference point. Moreover the average of daily solar radiation (SOLAR) is considered. For the SOLAR predictor, the average of the daily solar radiation is used in the Tavg model, while the daily solar radiation maximum is used in the Tmax model. SOLAR predictor is not applicable for Tmin model.

2.

Urban morphology predictors. Those are the percentage of pavement area over a radius of 50m, the average height to building area ratio, the total wall surface area, the Green Plot Ratio, the sky view factor and the average surface albedo.

The planners are not able to modify the overall climatic conditions, but they can modify the urban morphological conditions. With the temperature map, planners are able to analyze the impacts of their design to the environment. As an example, temperature maps are used to analyze and predict the impact of a new master plan as compared to the existing conditions in a Singapore estate and also to study two different greenery densities of the park, named as “Green Belt”. The calculated maximum temperature is shown in Fig. 4. The changes of maximum air temperature distribution pattern at different master plan models (Model 1 and Model 2) are mainly due to the change of greenery and building distributions. The removal of large greenery areas and its replacement with buildings increases the average air temperature, as seen in the Vista Xchange zone. The impact of the Green Belt in Model 2 (Fig. 4 right) that has a higher greenery density as compared to Model 1 (Fig. 4 middle) seems more noticeable, creating a larger “cool island” at the middle of the estate. Researchers have conducted various investigations and measurements in relation to the built environment. As a result, they have come out with various prediction models for different purposes, including impact mitigation strategies, climatic


Wong and Jusuf

data predictions, improved weather and air quality forecasts [46]. Nevertheless, these prediction models are too complicated for educated non-scientists, such as urban planners. In the end, they are often kept in the shelves until the scientists are engaged to do the assessment. By the time scientists finish their assessments, the planners have no time to redesign their master plans based on the scientists’ findings. There is a gap between scientists and planners. Furthermore, at the building design level, CAD software has been developed and integrated with some simulation software, called the Building Information Modeling (BIM). However, at urban or estate planning level, there is still no software or tool that can equip planners to design and perform assessment at the same time. These findings emphasize the need to develop a tool for planners.

Figure 4: The calculated average air temperature of current condition (Left), master plan model 1 (Middle) and master plan model 2 (Right). 2 (Right).

The Screening Tool for Estate Environment Evaluation (STEVE) was developed with a motivation to bridge research findings, especially air temperature prediction models, and urban planners. p lanners. STEVE is a web-based application a pplication that is specific to an estate and it calculates the Tmin, Tavg and Tmax of a point of interest



13

for the existing conditions and future conditions (proposed master plans) of a specific area or estate. The air temperature prediction models that have been briefly mentioned above are used in this application. The map of estate’s existing e xisting condition or future development is displayed in STEVE interface. The viewing level of the map is set into three levels. In level 1 (Fig. 5), it displays a complete estate map including the zoning boundaries, which are darkened when the mouse is pointed to the selected zone. Users are able to zoom in the map into the second view level by clicking either the selected zone or the zoom-in button (Fig. 6).

Figure 5: First viewing level of the map.

Figure 6: Second viewing level of the map.


Wong and Jusuf

Figure 7: Third viewing level of the map.

The designated points appear for the users’ selection in this viewing level and then, users are able to predict air temperatures condition by clicking the selected point. A circle with the radius of 50 meters blinks to provide indication of the urban morphological distribution that influence the air temperatures at the selected point (Figs. 7 and 8).

Figure 8: Calculator interface.



15

At the left hand side of the existing or proposed master plan map, the calculator interface appears with preloaded values of different parameters for the selected point (Fig. 8). The preloaded values can be changed according to the users’ needs and the predicted air temperature results appear with a push on the “Calculate” button. URBAN GREENERY

Planting of vegetation in urban areas is one of the main strategies employed to mitigate the UHI effect, since vegetation plays a significant role in regulating the urban climate. It is an effective measure to create “oasis effect” and to mitigate urban warming at both macro- and micro-levels. Trees alter the environment by moderating the climate, improving air quality, conserving water and protecting wildlife. Basically, greenery ameliorates the urban climate by moderating the effects of sun, wind and rain. Trees cool the environment through shading and evapotranspiration. Solar radiation is either absorbed or deflected by leaves during hot shinny days and is transformed into latent heat converting water from liquid to gas which in turn results in a lower leaf temperature, lower ambient air temperature and higher humidity through the process of evapotranspiration. Hence, it feels much cooler under trees’ shading than exposed to direct sunlight. The energy budget of plants plants explains explains the whole whole evapotr evapotranspi anspiratio ration n process process [47], [47], as as follows follows:: Φn –

C – λ E = M + S

Where: Φn

: Net heat gain from radiation (short-wave radiation and long-wave radiation). This is often the largest part and it drives many energy fluxes.

C : Net sensible heat loss, which is the sum of all a ll heat losses to the surroundings by conduction and convection. λ E

: Net latent heat loss, which is required to convert all water evaporated from the liquid to the vapor state and is given by the product of the evaporation rate E and the latent heat of vaporization of water (λ = -1 o 2.454 MJ kg at 20 C).


Wong and Jusuf

M : Net heat stored in biochemical reactions, which represents the storage of heat energy as chemical bond energy and is dominated by photosynthesis of respiration. S : Net physical storage of thermal energy, which includes the energy used for heating the plant as well as heat used to raise the temperature of the air. Some researchers reported that the energy transferred to latent heat through plants can be very high. Almost 1460kg of water is evaporated from an average tree during a summer sunny day, a cooling effect that is equal to five average air conditioners [48]. A single tree has the capability to moderate the surrounding microclimate, but its impacts are limited. Large urban parks, on the other hand, extend the positive effects to the surrounding built environment. Chen and Wong studied two urban parks in Singapore and concluded that a maximum 1.3K average temperature difference was observed around the parks. The temperatures measured within parks also have strong relationship with the density of plants, i.e. Leaf i.e. Leaf Area Index (LAI). Plants with higher LAIs may cause lower ambient temperatures. Results derived from the simulation study showed that a significant amount (almost 10% reduction of the cooling load) of energy consumption for cooling may be saved when buildings are built near parks [49]. A study in Japan [50] showed that even a small area of 60x40m can create a notable cooling effect. The maximum difference between inside and outside of the small greenery area was 3K. The study also showed that the air temperature distribution was closely related to the distribution of greenery in the city. Jauregui found that in a large urban park in Mexico City, the ambient temperature was 2-3K lower than its surrounding builtup area and its influence reached a distance of 2km, about the same as its width [51]. Therefore it can be stated that groups of trees may effectively improve the thermal environment of the urban area. Trees have impressive shading effects towards the built environment. Dense foliage trees are able to intercept the incoming solar radiation by 70% – 90% [5254]. The shading effect provided by the plants on the surface of the buildings



17

lowers the surface temperatures and subsequently lowers the cooling energy consumption. Strategically located plants may reduce the cooling energy consumption between 25% – 80% [55-61]. They can be in the form of trees located at the eastern or western side of the building’s wall, as well as rooftop or vertical greenery. Extra savings can be observed when air conditioning units are well shaded by plants [62]. The development of roof and wall planting has also been increased in the recent years, with a number of installations for roof gardens and vertical greenery in various building types, such as airports, hotels, residential and educational buildings, shopping malls and other facilities. Wong studied the impact of intensive and extensive rooftop greenery to the buildings energy behavior and environment [63]. Rooftop greenery can provide benefits not only to the building but also to the ambient temperature conditions. With the intensive rooftop garden system, the surface temperature may reduce up to 3.1K and the ambient temperature at 1 m may reduce up to 1.5K as shown in Fig. 9. The impact of rooftop greenery is even more pronounced for metal roofs. Without plants, the metal surface can be up to 60-70°C during daytime and lower than 20°C at night. With plants, it ranges only from 24°C to 32°C.

Figure 9: Comparison of surface and ambient temperatures measured with different plants (Source: Wong et al . 2007).

Rooftop greenery research in Japan concluded that the temperature above the rooftop greenery can be reduced of around 2-5K compared to a hard surface [64,


Wong and Jusuf

65]. Meanwhile, the surface temperature under the plants is reduced of almost 2530K compared to the metal surface during the peak hour of clear days. Fioretti investigated the rooftop greenery performance in Mediterranean climate of Italy. The study also found a 5-6K temperature reduction above the green roof while the foliage reduced the solar radiation incidence on the roof surface between 80% 90% [66]. In the city, the amount of buildings’ façade surfaces is quite large compared to the roof surfaces. Hence, greening of building façade surface, known as vertical greenery system, has a great potential in mitigating the UHI effect through evapotranspiration and shading [67]. Vegetation can dramatically reduce the maximum temperature of a building by shading its walls from the sun, with daily temperature fluctuation being reduced by as much as 50% [68]. In addition, a façade fully covered with greenery is protected from the solar radiation intensity in the summer and it can reflect or absorb by its leaf cover between 40% - 80% of the received radiation, depending on the amount and the type of greenery [31]. A research in the humid climate of Hong Kong showed a maximum temperature decrease of 8.4K by vertical greenery systems in an urban canyon [69]. The reduction is significant as the distribution of ambient air in a canyon influences the energy consumption of buildings. Higher temperatures in a canyon increase the heat convection into the building and correspondingly increase the cooling load [70]. Surface temperatures of vertical greenery systems have been observed in different settings at the University of Toronto since 1996 [71]. These results have consistently demonstrated that areas with vertical greenery are cooler than light-colored brick walls and black surfaces that are typically found in urban areas. In Japan, experiments show that vines can reduce the surface temperature of a veranda with south-western exposure by 13-15K and the air temperature by 13K [52]. In Africa, a temperature reduction of 2.6K was observed behind vegetated panels of vines [72]. Therefore, together with the insulation effect of vegetation, the temperature fluctuations at the wall surface can be reduced between 10-60K to 5K-30K [73]. In Singapore, eight different vertical greenery systems were studied vs. vs. their thermal performance [74]. The reason of the differences in the thermal


Cool Materials for the Built Environment 19

performance of these vertical greenery systems can be a combination of various factors, including the substrate type, the insulation of the system structure, the substrate moisture content as well as the shading and insulation of greenery coverage. At the same time, the interactions between leaf area, geometry, color and other microclimatic parameters such as solar radiation are complex and may result in different cooling efficiencies during day and night. Maximum reduction of 11.58K in the wall surface temperature on clear days is observed by the vertical greenery systems (Fig. 10) and a reduction of up to 3.33K in ambient air temperature from a distance of 0.15m away (Fig. 11) compared to a regular concrete wall.

Figure 10: Wall and substrate surface temperature of Vertical Greenery System no.5 (Source: Wong et al. 2010).

Figure 11: Ambient temperatures at a distance of 0.15m away from Vertical Greenery System no 1, 2 and 4 (Source: Wong et al. 2010).


Wong and Jusuf

URBAN VENTILATION

Wind speed in the urban areas is seriously decreased compared to the undisturbed wind speed. Moreover wind direction may be altered. The roughness of buildings and urban structures (geometry) affects wind within the cities and slows down wind speeds, thus decreases the natural ventilation potential and increases the pollutants’ concentration. One of the causes of UHI is the reduced turbulent transfer of heat within streets, due to the decrease of wind speed. The serious reduction of wind speed in urban canyons hampers the application of airflow through natural ventilation for dense urban environments [70]. The decrease in outdoor ventilation increases the outdoor pollutant concentrations and creates poor thermal comfort conditions. This has a trickling effect to the indoor environments as well. Experimental evaluation of airflow reduction in urban canyons has shown a reduction of 90% [75]. Natural ventilation is a good strategy for achieving acceptable thermal comfort, dilution of pollutant concentrations and dispersion of heat flux. Air movements determine the convective heat and mass exchange of the human body with the surrounding air. Higher air velocities increase the evaporative rate of skin surface and consequently enhance the cooling sensation [76]. Oke classified the wind variation with height over the cities with a two-layer classification of urban modification, the ‘urban canopy layer (UCL)’ and ‘urban boundary layer (UBL)’, see Fig. 12. As the air flows from rural to urban areas, the boundary layer must adjust to the new boundary conditions defined by the skyline of the city [77]. The ‘urban canopy layer (UCL) ’ or ‘obstructed sub-layer’ extends from the ground surface up to the height of the buildings. The climatic conditions cond itions inside the UCL are determined by various urban configurations and material properties. In general, the wind speed inside this layer significantly decreases relative to the undisturbed wind speed. The turbulence decreases with increasing height due to ground obstacles and thermal airflow instabilities. The ‘urban boundary layer (UBL)’, or ‘free surface layer’, lies above the buildings’ roof tops. Its thickness (from hundreds to thousands of meters) is determined by the gradient height at



21

which surface friction of the ground no longer affects the general wind flow. It varies from one point to another because of the variable heights of the buildings below and wind speed. It is also more homogeneous in its properties over the urban area than the UCL. In the UBL, the complex terrain increases the roughness of the surface and therefore increases the turbulence.

Figure 12: Schematic representation of the urban atmosphere illustrating a 2-layer classification of urban modification (Source: Oke 1987).

In highly urbanized cities like Hong Kong or Singapore, most residential estates have high canyon geometry ratios e.g. 2-3. e.g. 2-3. According to Oke, 70-80% of daytime radiant energy surplus within urban canyons is dissipated to the air through turbulent transfer. The balance 20-30% is stored and released at night [78]. Some key parameters that affect the air flow in urban landscape [14, 79] are the following: 1.

The prevailing breezeway or air path. The overall permeability of the district has to be increased at ground level. This is to ensure that the prevailing wind travels along breezeways and major roads can penetrate deeply into the district. This can be achieved by proper linking of open spaces, creation of open plazas at roads’ junctions, maintaining low-rise structures along prevailing wind direction.

2.

Variation of building height. Varying the height of buildings significantly improves the penetration of the airflow in the urban landscape. Stepping building height in rows would also create better


Wong and Jusuf

wind at higher levels if the differences in building heights between rows are significant. 3.

Orientation and layout of the buildings/streets with adequate gaps between buildings are essential for good airflow. The main streets and breezeways should be aligned in parallel or up to 30° to the prevailing wind direction, in order to maximize the penetration of prevailing winds through the estate. Building axis should be parallel to the prevailing wind to avoid obstruction (Fig. 13).

4.

Increasing the permeability of building blocks by the provision of void decks at ground level or at mid-span. This helps improve the ventilation for pedestrians, and to remove the pollutants and heat generated at ground level.

Figure 13: Orientation of street grids (Source: Ng E. 2009).

When the prevailing wind blows perpendicular to the street canyon, there are three regimes of wind patterns, which are a function of building (L/H) and canyon geometries (H/W) [70, 80, 81]. These are the isolated roughness flow (IRF), the wake interference flow (WIF) and the skimming flow (SF), see Fig. 14. Wind flows are considered perpendicular when the predominant airflow direction is approximately (±30°) to the long axis of the street canyon.



23

Figure 14: (a), (b), (c) Perpendicular flow regimes in urban canyons for different aspect ratios (Source: Oke 1988).

The airflow pattern of the widely spaced buildings, i.e. H/W i.e. H/W < 0.4 for cubic and < 0.3 for row buildings, is similar to the airflow pattern of the isolated ones (Fig. 14a). For a closer spacing, such as H/W up to 0.7 for cubes and 0.65 for row buildings, the airflow pattern changes to wake interference flow (Fig 14b). It is characterized by a reverse (with respect to upwind flow direction) horizontal flow in the lower canyon and forward flow along the canyon top. A small vortex may appear behind the upwind building but it is not dominant. An area of low wind speed appears in the canyon center. Maximum wind occurs at the top of the canyon and relatively high wind speed occurs down the face of the downwind building. At the higher building geometry (H/W) and density, the main airflow skims over the building rooftops and the bulk of the airflow does not enter the canyon. This flow is named as skimming flow (Fig. 14c). The relationship between the three principle airflow regimes and their respective canyon H/W and L/H ratios has been summarized by Oke [80], as shown in Fig. 15.


Wong and Jusuf

Figure 15: Threshold for flow regimes in urban canyons as functions of urban canyon H/W & L/W ratios (Source: Oke 1988).

Cool Materials

The optical and thermal characteristics of building materials that determine the energy consumption in the built environment, is the solar radiation albedo and the emissivity of long wave radiation. Those parameters have a very important impact on the urban energy balance as seen in Fig. 16. The albedo of a surface is defined as its reflectivity, integrated hemi-spherically over the wavelength. The usage of high albedo materials keeps the surface temperature lower by reducing the amount of solar radiation absorbed into the buildings and the ambient air temperature at urban level [82]. Table 2 shows the albedo of various typical urban materials and areas [70, 83-85].

Figure 16: Diagram of cool roof system (Source: U.S. Cool Roof Rating Council).



25

Table 2: Albedo of typical urban materials and areas [70, 83-85] Surface

Albedo

Streets Asphalt (fresh 0.05, aged 0.2)

0.05 - 0.20

Walls Concrete Brick/Stone Whitewashed stone White marble chips Light colored brick Red brick Dark brick and slate Limestone

0.10 - 0.35 0.20 - 0.40 0.80 0.55 0.30 - 0.50 0.20 - 0.30 0.20 0.30 - 0.45

Roofs Smooth-surface asphalt (weathered) Asphalt Tar and gravel Tile Slate Thatch Corrugated iron Highly reflective roof (weathered)

0.07 0.10 - 0.15 0.08 - 0.18 0.10 - 0.35 0.10 0.15 - 0.20 0.10 - 0.16 0.60 - 0.70

Paints White, whitewash Red, brown, green Black

0.50 - 0.90 0.20 - 0.35 0.02 - 0.15

Urban Areas Range Average

0.10 - 0.27 0.15

Other Light-colored sand Dry grass Average soil Dry sand Deciduous plants Deciduous forests Cultivated soil Wet sand Coniferous forests Dark cultivated soil Grass and leaf mulch

0.40 - 0.60 0.30 0.30 0.20 - 0.30 0.20 - 0.30 0.15 - 0.20 0.20 0.10 - 0.20 0.10 - 0.15 0.07 - 0.10 0.05

Extensive studies on cool coating materials for roofs or other buildings’ surfaces as one of solutions to mitigate UHI have been conducted during the last decade.


Wong and Jusuf

Cool roof is identified as a roofing system that is able to deliver high solar reflectance and high thermal emittance [86]. Cool roof system is purposed to reduce heat load for air conditioning system, energy usage and CO2 released to atmosphere. Bretz and Akbari [87] studied the relation between albedo of three different coatings, which were applied on three buildings roofs, and building energy consumption. From the two months up to six years measurements, it is shown that the higher the roof albedo value, the higher the percentage of energy savings. However, over the time, albedo values of the coated roofs dropped due to the accumulation of dirt and microbial growth causing at the same time, a similar reduction of the energy saving percentage. Experiments of washing the roof showed that albedo value drops was only temporary and it would recover 90% of its original value upon the washing although it may not be cost co st effective. ENERGY STAR labeled roof products are able to reduce surface temperature up to o 100F (equal to 37.79 C) and peak cooling demand by 10-15%. White or light colors coated roofs have been promoted widely in the U.S. to achieve cooler roof surface temperatures by increasing solar reflectance as a complementary alternative to metal roofing system which has high thermal emittance but low solar reflectance [88]. Synnefa et al. al. [89] conducted a study on the thermal performance of non-white cool colored coatings. Ten prototypes of cool colored coating tiles were compared with standard coating tiles for a period of three months during daytime and nighttime. The results show that cool colored coating tiles are more selective in absorbing infrared band, resulting in higher solar reflectance and lower surface temperature. From their experiment, there is a correlation between solar reflectance and surface temperature during daytime. These cool coatings can be applied to other building materials besides roofs. Another experimental study done by Simpson and McPherson [90] on three identical scaled model houses in Tucson, Arizona for period of three months showed that white roof, which has a higher albedo compared to silver or gray and o brown roofs, reduced the surface temperature to almost a lmost 20 C compared to a gray o or silver roof and to almost 30 C compared to a brown roof. However, detailed observation also showed that increasing building surface's albedo may not be effective in reducing its temperature if the emissivity is also reduced.



27

The issues of aesthetic and maintenance require darker roof colors more desirable than white or light coated color roofs. Karlessi et al. [91] al. [91] conducted a comparative study between thermochromic coatings, cool and common coatings. The research showed that thermochromic coatings are able to respond thermally to the environment. Thermochromic coating colors faded or became colourless when the ambient temperature was higher than the transition temperature. Under these conditions the surface reflects more solar radiation, hence, reduces the surface temperature. With similar principles with cool roofs, cool pavements have been promoted aggressively the last years. Akbari et al. [92] al. [92] believes that by implementing cool roofs and cool pavements, the urban area’s overall albedo can be increased by about 0.1. The study predicted that by increasing albedo of urban roofs and paved surfaces worldwide offsets 44Gt of emitted CO 2. Kinouchi [93] studied the structure of pigment and coating with low reflectivity in the visible part of sunlight spectrum and high reflectivity of near infrared. The field measurement on paint coated asphalt pavement indicated 15°C lower than conventional asphalt pavement. ACKNOWLEDGEMENTS

Part of information included in this chapter has been previously published in author's own publication. CONFLICT OF INTEREST

The author(s) confirm that this article content has no conflict of interest. REFERENCES [1] [2] [3] [4] [5]

Oke, TR. Boundary Layer Climates. Cambridge, Cambridge University Press. 1987; p. 262-303. Mc. Gregor, GR, Nieuwolt, S. Tropical Climatology. New York, Wiley. 1998. Oke, TR and Eas, C. The urban boundary layer in Montreal. Boundary Layer Meteorology 1971, 1: 411-437. Padmanabhamurty, B. Microclimates Microclimates in tropical urban complexes. Energy and Buildings 1990/1991; 15 (1-2): 83-92. Sani, S. Urban climatology in Malaysia: an overview. overview. Energy and Buildings 1990/1991; 15 (3-4):105-117.


[6] [7] [8]

[9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19]

[20]

[21] [22] [23]

[24] [25] [26] [27]

Wong and Jusuf

Swaid, H, Hoffman, Hoffman, ME. Climate impacts of urban design features for for high and mid mid latitude cites. Energy and Buildings 1990; 14: 325-336. Eliasson I. Urban Nocturnal Temperatures, Street Geometry and Land Land Use. Use. Atmospheric Environment 1996; 30 (3): 379-392. Giridharan, R, Lau, SSY, Ganesan, S, Givoni, B. Urban design factors influencing heat island intensity in high rise high density environments of Hong Kong. Building and Environment 2007; 42: 3669-3684. Wong, NH NH and Chen, Y. Y. Study of green areas and urban heat island in a tropical city. Habitat International 2005; 29: 547–558. Jusuf, SK, Wong, NH. STEVE Tool: a web web application of Singapore air temperature prediction model, model, Accepted for publication in Journal Journal of Green Building. Building. Santamouris, M. Energy and climate in the urban built environment. environment. London, James & James Science Publishers. 2001. European Commission. European sustainable cities project. Luxemburg, OOPEC. 1996. Santamouris, M. Energy and climate in the urban built environment. environment. London, James & James Science Publishers. 2001. Wong NH, Chen Y. Tropical Tropical urban heat islands: Climate, buildings buildings and greenery. greenery. New York, Taylor & Francis 2009; p. 52-67. Crutzen PJ. PJ. The growing urban urban heat and pollution pollution "island" effect—impact on chemistry chemistry and climate. Atmospheric Environment 2004; 38: 3539-540. European Commission. European sustainable cities project. Luxemburg, OOPEC. 1996. Chen Y, Wong NH. Thermal benefits benefits of parks. Energy Energy and buildings 2006; 38: 105-20. Thorsson S. Increased heat stress in Swedish cities cities due to climate change: change: the impact impact of urban geometry on thermal comfort. IAUC Newsletter 2008; 29: 11-3. Steemers KA, KA, Ramos MC, MC, Sinou M. Urban morphology. In: Nikolopoulou M, Ed. Designing open spaces in the urban environment: a bioclimatic approach. Greece, CRES. 2004; pp. 17-21. Katzschner L, L, Bosch U, Roettgen M. Thermal Thermal comfort mapping mapping and zoning. In: In: Nikolopoulou M, Ed. Designing open spaces in the urban environment: a bioclimatic approach. Greece, CRES. 2004; p. 22-6. Sharlin N, N, Hoffman ME. The urban complex as a factor factor in the air temperature temperature pattern in in a Mediterranean coastal region. Energy and buildings 1984; 7: 149-58. Moriyama M, Matsumoto Matsumoto M. Control of urban night temperature in semi-tropical semi-tropical regions regions during summer. Energy and buildings 1988; 11: 213-19. Giridharan R, Lau SSY, Ganesan S, Givoni, B. Urban design factors influencing heat heat island intensity in high rise high density environments of Hong Kong. Building and Environment 2007; 42: 3669-684. Katzschner L. L. The urban urban climate climate as a parameter parameter for urban development. development. Energy and buildings 1988; 11: 137-47. Matzarakis A. Country Country Report Urban Climate Climate Research Research in Germany. IAUC Newsletter 2005; 11: 4-6 Mayer H. Results Results from the research program “STADTKLIMA “STADTKLIMA BAYERN” BAYERN” for urban planning. Energy and buildings 1988; 11: 115-21. CUHK. Urban Climatic Climatic Map and Standards for Wind Environment - Feasibility Feasibility Study. Working paper 1A: draft urban climatic analysis map. CUHK: Hong Kong. 2008; p. 13.


[28]

[29] [30] [31] [32]

[33] [34] [35] [36] [37] [38] [39] [40] [41] [42]

[43]

[44] [45] [46]

[47] [48]


29

Scherer D, Fehrenbach U, Beha H.-D, Parlow E. E. Improved concepts and methods methods in analysis and evaluation of the urban climate for optimizing urban planning process. Atmospheric Environment 1999; 33: 4185-4193. Barlag A-B, A-B, Kuttler Kuttler W. The The significance significance of country country breezes for urban planning. Energy Energy and buildings 1990/91; 15-16: 291-297. CUHK. Urban Climatic Climatic Map and Standards for Wind Environment - Feasibility Feasibility Study. Working paper 1A: draft urban climatic analysis map. CUHK: Hong Kong. 2008; p. 19-38. Climate booklet for urban development. Ministry of Economy Baden-Wurttemberg Baden-Wurttemberg in Cooperation with Environmental Protection Department of Stuttgart; 2008. Katzschner L. A contribution contribution of urban urban climate studies to a new urbanity. urbanity. Paper Paper presented in th the 4 Japanese – German meeting on urban climatology, Climate analysis for urban planning. Tsukuba, 30 November – 2 December 2005. Jusuf SK, Wong NH, Hagen Hagen E, Anggoro Anggoro R, Yan Yan H. The influence of land use on the urban heat island in Singapore. Habitat International 2007; 31: 232-42. 232-42 . Cleugh H. Urban climates. climates. In: Henderson-Sellers Henderson-Sellers A, Ed. Ed. Future Climates of the World: World: A Modeling Perspective. Amsterdam and New York: Elsevier, 1995. Arnfield AJ. Street Street design and urban canyon solar access. Energy Energy and Buildings 1990; 1990; 14: 117-31. Oke TR. TR. Canyon geometry and the nocturnal urban urban heat island : comparison of scale model and field observations. J Climat 1981; 1: 237-254. Bärring I, I, Mattsson Mattsson JO, Lindqvist S. Canyon geometry, street temperatures temperatures and urban heat island in Malmö, Sweden. Int J Climat 1985; 5: 433-44. Chapman L, L, Thornes JE, Bradley Bradley AV. Rapid determination determination of canyon geometry parameters for use in surface radiation budgets. Theoretical and Applied Climatology 2001; 69: 81-89. Chen Y, Wong NH. Thermal benefits benefits of city parks. Energy and Buildings 2006; 38: 105120. Streiling S, Matzarakis A. Influence of single and small clusters of trees trees on the bioclimate of a city: a case study. Journal Arboriculture 2003; 29: 309-16. Knowles RL. RL. Energy and form: An ecological approach to urban growth. growth. USA: The MIT Press 1977. Giridharan R, R, Lau SSY, SSY, Ganesan S, Givoni B. Lowering Lowering the outdoor outdoor temperature temperature in highrise residential developments of coastal Hong Kong: the vegetation influence. Building and Environment 2008; 43: 1583-595. Berdahl P, Bretz S. Preliminary survey of the solar reflectance reflectance of cool roofing materials. materials. Energy and Buildings Special Issue on Urban Heat Islands and Cool Communities 1997; 25: 149–58. Taha H, Akbari, Akbari, H, Rosenfeld Rosenfeld A, Huang J. Residential Residential cooling cooling loads and the the urban heat island -the effects of albedo. Building and Environment 1988; 23: 271-83. Taha H. Modeling the impacts of large-scale albedo changes on ozone air air quality in the south coast air basin. Atmospheric Environment 1997; 31: 1667-76. Grimmond S, Blackett Blackett M. Urban surface surface energy balance: land land surface scheme comparison. Department of Geography. King’s College London, University of London. Newsletter 2008; 1. Jones HG. Plants and microclimate. microclimate. 2nd ed. Cambridge: Cambridge University Press. 1991. Moffat A, Schiler M. Landscape design that saves energy. New York: York: William Morrow and Company 1981.


[49] [50] [51] [52] [53] [54] [55] [56] [57] [58] [59] [60] [61] [62] [63] [64] [65] [66] [67]

[68] [69] [70] [71]

Wong and Jusuf

Chen Y, Wong NH. Thermal benefit of city parks. Ener parks. Energy gy and and buildi buildings ngs 2006; 2006; 38: 38: 105 – 20. 20. Saito I. Study of the the effect of of green areas areas on the thermal environment environment in an urban area. area. Energy and Buildings 1990/1991; 15-16: 493-98. Jaurequi E. E. Influence Influence of a large urban park park on temperature and convective precipitation in a tropical city. Energy and buildings 1990/1991; 15-16: 457-63. Hoyano A. Climatological Climatological uses of plants for solar solar control and and the effects effects on the thermal environment of a building. Energy and Buildings 1998; 11: 181-99. Papadakis G, G, Tsamis P, Kyritsis Kyritsis S. An experimental experimental investigation investigation of the effect of shading of plants for solar control of buildings. Energy and Buildings 2001; 33: 831-36. Simpson JR. Improved Improved estimates estimates of tree-shading effects on on residential residential energy use. Energy Energy and Buildings 2002; 34: 1067-76. De Walle DR, Heilser Heilser GM, Jacobs, RE. Forest home home sites influence influence heating and cooling energy. Journal of Forestry 1983; 84: 84-88. McPherson EG, EG, Simpson Simpson JR. Simulation Simulation of tree shade impacts on residential residential energy use for space conditioning in Sacramento. Atmospheric Environment 1998; 32: 69-74. McPherson EG, Herrington Herrington LP, LP, Heisler Heisler GM. Impacts of vegetation on residential heating heating and cooling. Energy and Buildings 1988; 12: 4 1-51. McPherson EG, Simpson Simpson JR, JR, Livingston Livingston M. Effects of tree landscapes on residential residential energy and water use in Tucson, Arizona. Energy and Buildings 1989; 13: 127-38. Parker JH. JH. Landscaping Landscaping to reduce reduce the energy used in cooling buildings. J Forest 1983; 1983; 81: 82-105. Raeissi S, S, Taheri M. Energy Energy saving by proper tree plantation. plantation. Building Building and Environment 1999; 34: 565-70. Simpson JR. Improved Improved estimates estimates of tree-shading effects on on residential residential energy use. Energy Energy and Buildings 2002; 34: 1067-76. Petit J, Bassert DL, DL, Kollin C. C. Building greener greener neighborhoods: trees as part part of the plan. plan. Washington, DC: Home Builder Press 1995. Wong NH, Tan PY, Chen Y. Study of thermal performance of extensive rooftop rooftop greenery systems in the tropical climates. Building and Environment 2007; 42: 25-54. Harazono Y. Effects of rooftop vegetation vegetation using artificial substrates on the urban climate and the thermal load of buildings. Energy and Buildings 1990/1991; 15-16: 435-42. Onmura S, Matsumoto M, Hokoi S. Study Study on evaporative evaporative cooling effect of roof lawn gardens. Energy and Buildings 2001; 33: 831-6. Fioretti R, Pall A, Lanza, Lanza, LG and Principi Principi P. Green roof roof energy and water related related performance in the Mediterranean Mediterranean climate. Building Building and Environment Environment 2010; 45: 1890-904. 1890-904. McPherson EG. EG. Preserving Preserving and restoring restoring urban urban biodiversity: biodiversity: cooling urban urban heat islands islands with sustainable landscapes. In: Platt RH, Rowntree RA, Muick PC, editors. The ecological city. Amherst, US: University of Massachusetts Press; 1994. p. 151–72. Dunnett N, Kingsbury N. Planting green roofs and living living walls. Portland, USA: Timber Timber Press; 2008. Alexandri E, Jones P. Temperature Temperature decreases decreases in an an urban canyon canyon due to to green walls walls and green roofs in diverse climates. Building and Environment 2008;43: 480–93. Santamouris M. The canyon effect. In: Santamouris Santamouris M, editor. Energy Energy and climate climate in the urban built environment. London, UK: James and James Publishers; 2001. p. 69–96. Bass B, Baskaran B. Evaluating rooftop and vertical gardens gardens as an adaptation strategy strategy for urban areas. Institute for Research and Construction. NRCC-46737, Project number A020, CCAF report B1046. Ottawa, Canada: National Research Council; 2003.


[72] [73]

[74]

[75] [76] [77] [78] [79] [80] [81]

[82]

[83] [84] [85]

[86] [87] [88] [89]

[90] [91]


31

Holm D. Thermal improvement improvement by means of leaf cover on external external walls walls – a simulation simulation model. Energy and Buildings 1989; 14(1): 19–30. Peck SW, Callaghan C, Bass B, Kuhn ME. Research Research report: greenbacks from green roofs: forging a new industry in Canada. Ottawa, Canada: Canadian Mortgage and Housing Corporation (CMHC); 1999. Wong NH, Tan YKA, Chen Y, Sekar K, Tan PY, Chan D, Chiang K, Wong NC. Thermal evaluation of vertical greenery systems for building walls. Building and Environment 2010; 45: 663-72. Geros V, Santamouris M, Tsangrassoulis Tsangrassoulis A, Guarracino G. Experimental evaluation of night ventilation phenomena. Energy and Buildings 1999; 29: 141–54. Feriadi H. H. Thermal comfort for natural ventilated ventilated residential buildings in the tropical climate. Unpublished PhD Dissertation, National University of Singapore 2003. Oke TR. Boundary Layer Climates. London, Routledge 1987; p. 274. 274. Oke TR. TR. Boundary Boundary Layer Layer Climates. Climates. London, Routledge Routledge 1987; p. 33-76. Ng E. Policies Policies and technical guidelines guidelines for urban planning planning of high-density high-density cities – air ventilation assessment assessment (AVA) of Hong Kong. Building and Environment 2009; 44: 1478-88. Oke TR. Street design design and urban urban canopy layer climate. climate. Energy and Buildings Buildings 1988; 11: 103-13. M. Hussain Hussain and B. E. Lee, Lee, An investigation investigation of of wind forces forces on three-dimensional three-dimensional roughness elements in a simulated atmospheric boundary layer flow: Part II Flow over large arrays of identical roughness elements and the effect of frontal and side aspect ratio variations, Report BS 56, Dept. Building Science, University of Sheffield, 1980. Santamouris M. Appropriate Appropriate materials materials for the urban environment. environment. In: Santamouris Santamouris M, editor. Energy and climate in the urban built environment. London, UK: James and James Publishers; 2001. p. 160-81. Bretz S, Akbari H, Rosenfeld A, A, Taha H. Implementation of solar reflective reflective surfaces: surfaces: materials and utility programs. LBL Report – 32467. University of California 1992 Baker MC. Roofs:designs, Roofs:designs, application and maintenance. maintenance. Montreal: Multi-science Multi-science Publications; 1980. Martien P, P, Akbari H and Rosenfeld Rosenfeld A. Light colored colored surfaces to reduce summertime summertime urban temperatures: benefits, costs and implementation issues. Presented at the 9 th Miami International Congress on Energy and Environment, Miami Beach Florida, 11-13 December 1989. Cool Roof Rating Council. www.coolroofs.org www.coolroofs.org Bertz SE, SE, Akbari H. Long-term Long-term performance performance of high-albedo high-albedo roof coatings. Energy Energy and Buildings 1997; 25:159–67. Energy Star. http://www.energystar.gov/inde http://www.energystar.gov/index.cfm?fuseaction= x.cfm?fuseaction=find_a_product.show find_a_product.show ProductGroup&pgw_code=RO Synnefa A, Santamouris M, Apostolakis Apostolakis K. On the development, development, optical optical properties properties and thermal performance of cool coloued coatings for the urban environment. Solar Energy 2006; 81: 488-497. Simpson JR, JR, McPherson McPherson EG. The effects of roof albedo modification modification on cooling cooling loads of scale model residences in Tucson, Arizona. Energy and buildings 1997; 25: 127-37. Karlessi T, Santamouris Santamouris M, Apostokalis K, Synnefa Synnefa A, Livada I. Development and testing of thermochromic coatings for buildings and urban structures. Solar Energy 2008; 83: 53851.


[92] [93]

Wong and Jusuf

Akbari H, Menon S, Rosenfeld A. A. Global cooling: increasing increasing world-wide world-wide urban albedos to offset CO2. Climate Change 2009; 94: 275-86. Kinouchi T, T, Yoshinaka Yoshinaka T, Fukae Fukae N, Kanda M. Development of cool pavement pavement with with dark colored high albedo coating. In: American Meteorological Society, ed. Proceedings of the fifth Conference on urban environment. 23-25 August 2004: Vancouver. American Meteorological Society 2004.

Urban Heat Island and Mitigation Strategies at City and Building

Recommend Documents