TP48200A-D15A1 & H15A3 & H15A5 V300R001 Quick Installation Guide 06

TP48200A-D15A1 & H15A3 & H15A5 V300R001

Quick Installation Guide

Issue

06

Date

2013-07-23

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2013. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd. Address:

Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China

Website:

http://www.huawei.com

Email:

[email protected]

Issue 06 (2013-07-23)

Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

i

TP48200A-D15A1 & H15A3 & H15A5 Quick Installation Guide

About This Document

About This Document Purpose This document describes the TP48200A-D15A1 & H15A3 & H15A5 in terms of its structure, components, installation, and commissioning.

Intended Audience This document is intended for: 

Installation and commissioning engineers



Technical support engineers

Symbol Conventions The symbols that may be found in this document are defined as follows.

Symbol

Description Indicates a hazard with a high level or medium level of risk which, if not avoided, could result in death or serious injury.

Indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.

Indicates a potentially hazardous situation that, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. Provides a tip that may help you solve a problem or save time. Provides additional information to emphasize or supplement important points in the main text.

Issue 06 (2013-07-23)


ii


About This Document

Change History Changes between document issues are cumulative. The latest document issue contains all the changes made in earlier issues.

Issue 06 (2013-07-23) Modified section 7.1.1 UIM02C.

Issue 05 (2013-04-28) Optimized the content of the document, including standardizing the terminology and improving the accuracy of the description.

Issue 04 (2013-02-28) Add the installation dimensions for the cabinet installation holes.

Issue 03 (2013-01-09) This issue is the third official release, which incorporates the following changes: Chapter 6 Installing Components

Modify the picture of Install a temperature and humidity sensor. Chapter 8 Powering On and Commissioning

Set battery fuse break alarm " Enable/Disable" status is added.

Issue 02 (2012-11-12) This issue is the second official release, which incorporates incorporates the following changes: Port description is modified.

Issue 01 (2012-07-28) This issue is used for first office release.

Issue 06 (2013-07-23)


iii


Contents

Contents About This Document .............................. .................................................... ............................................ ............................................. .......................................... ................... ii 1 Safety Precautions .................................. ........................................................ ............................................ ............................................. ........................................... .................... 1 1.1 Health and Safety ............................................................................................................................................. 1 1.1.1 Overview .............................................................. .............................................................. ..................... 1 1.1.2 Electrical Safety ................................................................................................................. ..................... 3 1.1.3 Inflammable Environment ...................................................................................................................... 4 1.1.4 Battery ....................................................... .............................................................. ................................ 4 1.1.5 Working Working at Heights ............. ................................................................. ................................................... 6 1.1.6 Using Ladders ......................................................................................................................................... 7 1.1.7 Mechanical Safety .......................................................... ............................................................... .......... 7 1.1.8 Bundling Signal Cables ............................................................. .............................................................. 8 1.2 Equipment Safety ............................................................................................................. ................................ 9 1.2.1 Electricity Safety ............................................................ ............................................................... .......... 9 1.2.2 Electrostatic Discharge............................................................................................................................ 9 1.2.3 Laying Cables ....................................................................................................................................... 10

2 Installation Preparations ............................................ ................................................................... ............................................. ........................................ .................. 11 11 2.1 Tools ........................................................ ................................................................. ...................................... 11 2.2 Installation Clearance Requirements .............................................................................................................. 12 2.3 Prepare Cables ............................................................... .............................................................. ................... 12

3 Configuration.............................................. .................................................................... ............................................ ............................................. ..................................... .............. 14 4 Installing the Cabinet........................................... .................................................................. ............................................. ............................................ ......................... ... 18 5 Installing a PGND Cable............................................ ................................................................... ............................................. ........................................ .................. 21 6 Installing Components.................................. Components........................................................ ............................................. ............................................. ................................ .......... 22 6.1 Installing Rectifiers ........................................................................................................................................ 22 6.2 Installing a Smoke Sensor(Optional) ............................................................................................................. 23 6.2.1 Securing the Smoke Sensor ................................................................................................................... 23 6.2.2 Connecting the Smoke Sensor ............................................................. ................................................. 23 6.3 Installing a Temperature and Humidity Sensor(Optional) ........................................................... ................... 24 6.3.1 Securing the Temperature and Humidity Sensor ..................................................... .............................. 24 6.3.2 Connecting the Temperature Temperature and Humidity Sensor ............................................................ ................... 24

Issue 06 (2013-07-23)


iv


Contents

6.4 Installing a Water Sensor(Optional) ..................................................................................................... .......... 25 6.4.1 Securing the Water Sensor ...................................................................................... .............................. 25 6.4.2 Connecting the Water Sensor .................................................................................. .............................. 25

7 Installing Cables ........................................... .................................................................. ............................................. ............................................. ................................. .......... 27 7.1 Installing Signal Cables and Communication Cables....................................................... .............................. 27 7.1.1 UIM02C ............................................................... .............................................................. ................... 27 7.1.2 Installing Dry Contacts and Boo lean Values Values Signal Cables .................................................................. 29 7.1.3 Installing Sensor Cables ............................................................ ............................................................ 29 7.1.4 Installing Communications Cables ...................................................... ................................................. 30 7.2 Installing Po wer Cables ........................................................... ............................................................... ........ 30 7.2.1 Installing DC Output Cables ................................................................ ................................................. 31 7.2.2 Installing Storage Batteries and Copper Bars ........................... ............................................................ 32 7.2.3 Installing AC Output Cables ........................................................................ ......................................... 34 7.2.4 Installing AC Input Cables ........................................................ ............................................................ 35

8 System Commissioning ............................................................. .................................................................................... .............................................. ......................... .. 38 8.1 Installation Verification ........................................................... ............................................................... ........ 38 8.2 Powering On and Commissioning ................................................................ .................................................. 38 8.2.1 Setting Parameters ................................................................................................................................ 38 8.3 Powering On................................................................................................................................................... 42

Issue 06 (2013-07-23)


v


1 Safety Precautions

1

Safety Precautions

1.1 Health and Safety 1.1.1 Overview Introduction This section describes the safety precautions you must take before installing or maintaining Huawei equipment. 

To ensure safety safety of humans and the equipment, pay attention to the safety symbols on the equipment and all the safety instructions in this document.



The "NOTE", "CAUTION", and "WARNING" "WARNING" marks in other documents do not represent all the safety instructions. They are only supplements to the safety instructions.



Installation and maintenance personnel must understand basic safety precautions to avoid hazards.



When operating Huawei equipment, in addition to following the general precautions in this document, follow the specific safety instructions given by Huawei.



Only trained and qualified personnel are allowed to install, operate, and maintain Huawei equipment.

Local Safety Regulations When operating Huawei equipment, you must follow the local laws and regulations. The safety instructions in this document are only supplements to the local laws and regulations.

General Requirements To minimize risk of personal injury and damage to equipment, read and follow all the precautions in this document before before performing any any installation or maintenance. maintenance. Ensure that the instructions provided in this document are followed completely. completely. This section also provides guidelines for selecting the measuring and testing devices.

Installation 

The device (or system) must be installed in an access-controlled location.



The device can be mounted only on concrete or non-combustible surfaces.

Issue 06 (2013-07-23)


1





The device must be fixed securely on the floor or to other immovable objects such as walls and mounting racks before operation.



When installing the unit, always make the ground connection first and disconnect it at the end.



Do not block the ventilation while the device is operating. Keep a minimum distance of 5 cm between the device and the wall or other objects that may block the ventilation.



Tighten the thumbscrews by using a tool after initial installation and subsequent access to the panel.



Do not damage the ground conductor or operate the device in the absence of a properly installed ground conductor. conductor. Conduct the electrical inspection carefully.



The device (or system) must be connected permanently to the protection ground before an operation. The cross-sectional area of the protective ground conductor must be at least 2 10 mm .



For AC-supplied models: The device applies to TN or TT power system.



For DC-supplied models: Reinforced insulation or double insulation must be provided to isolate the DC source from the AC mains supply.



For DC-supplied model: The device applies to DC power source that complies with th e Safety Extra-Low Voltage (SELV) requirements in IEC 60950-1 based safety standards.



Prepared conductors are connected to the terminal block, and only the appropriate AWG/Type of wire is secured with the lug terminals.

Ground

Power Supply

Human Safety 

Do not operate the device or cables during lightning strikes.



Remove the AC power connector when there is lightning. Do not use fixed terminals or touch terminals or antenna connectors when there is lightning.



To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telecommunication network voltage (TNV) circuits.



Move or lift the chassis by b y holding its lower edge. Do not hold the handles on certain modules such as power supply, supply, fans, and boards because they cannot support the weight of the device.



At least two persons are required to lift the chassis. When lifting it, keep your back straight and move stably.



Do not wear jewelry or watches when you operate the device.



Only qualified professional personnel are allowed to install, configure, operate, and disassemble the device.



Only the personnel authenticated or authorized by Huawei are allowed to replace or change the device of the parts of the device (including the software).



Any fault or error that might cause safety problems must be reported immediately to a supervisor.



Only qualified personnel are allowed to remove or disable the safety facilities and to troubleshoot and maintain the device.

Operator

Issue 06 (2013-07-23)


2



1.1.2 Electrical Safety High Voltage

The high voltage power supply provides power for the device operation. Direct or indirect contact (through damp objects) with high voltage and AC mains supply may result in fatal danger. 

During the installation of the AC power supply facility, follow the local safety regulations. The personnel who install the AC facility must be qualified to perform high voltage and AC operations.



Do not wear conductive articles, such as watches, hand chains, bracelets, and rings during the operation.



When water is found in the rack or the rack is damp, switch off the power supply immediately.



When the operation is performed in a damp environment, make sure that the device is dry.

Non-standard and improper improper high voltage operations operations may result in fire and and electric shock. Therefore, you must abide by the local rules and regulations when bridging and wiring AC cables. Only qualified personnel are allowed to perform high voltage and AC operations.

Before powering on a device, ground the device. Otherwise, personal injury or device damage may be caused by high leakage current.

Tools

Dedicated tools must be used during high voltage and AC operations. Avoid Avoid using ordinary tools.

Issue 06 (2013-07-23)


3



High Electrical Leakage

Ground the device before powering it on. Otherwise, personal injury or device damage may be caused by high leakage leakage current. If a "high electrical leakage" tag is present on the power terminal of the device, you must ground the device before powering it on.

Power Cable

Do not install or remove power cables when the device is on. Transient contact between between the core of the power cable and the conductor may generate electric arcs or sparks, which may cause fire or hurt human eyes. 

Before installing or removing the power cable, turn off the power switch.



Before connecting a power cable, check that the label on the power cable is correct.

1.1.3 Inflammable Environment Operating the electrical device in an inflammable environment can be fatal.

Do not place the device in an environment that has inflammable and explosive air or gas. Do not perform any operation in this environment.

1.1.4 Battery Storage Battery

Before operating storage batteries, carefully read the safety precautions for battery handling and connection.

Issue 06 (2013-07-23)


4



Improper handling of storage batteries causes hazards. When operating storage batteries, avoid short circuit and overflow or leakage of the electrolyte. Electrolyte overflow may damage the device. It will corrode metal parts and circuit boards, and ultimately damage the device and cause short circuit of circuit boards.

Basic Precautions Before installing and maintaining the battery, battery, note the following: 

Do not wear metal articles such as wristwatch, hand chain, bracelet, and ring.



Use special insulation tools.



Take care care to protect your eyes when operating the device.



Wear rubber gloves and a protective coat in case of electrolyte overflow.



When handling a storage battery, battery, ensure that its electrodes are upward. Leaning or reversing the storage battery is prohibited.

Short Circuit

Battery short circuit may cause human injuries. Although the voltage of ordinary batteries is low, low, the instantaneous high current caused by the short circuit releases a great deal of energy. energy. There is danger of explosion if the battery is incorrectly replaced. Therefore, Therefore, replace the battery only with the same same or equivalent type recommended recommended by the manufacturer manufacturer..

Keep away metal objects, which may cause battery short circuit, from batteries. If metal objects must be used, first disconnect the batteries in use before performing any other operations.

Hazardous Gas

Issue 06 (2013-07-23)


5





Do not use unsealed lead acid storage batteries. Lead acid storage batteries must be placed horizontally and stably to prevent the batteries from releasing flammable gas, which may cause fire or erode the device.



Lead acid storage batteries in use emit flammable gas. Therefore, ventilation and fireproofing measures must be taken at the sites where lead acid storage batteries are used.

Battery Temperature

If a battery overheats, the battery may be deformed or damaged, and the electrolyte may overflow. When the temperature of the battery is higher than 60 ºC, check the battery for electrolyte overflow. overflow. If the electrolyte overflows, absorb and counteract the electrolyte immediately. immediately.

Battery Leakage

When the electrolyte overflows, absorb and counteract the electrolyte immediately. immediately. When moving or handling a battery whose electrolyte leaks, note that the leaking electrolyte may hurt human bodies. When you find the electrolyte leaks, use the following substances to counteract and absorb the leaking electrolyte: 

Sodium bicarbonate (baking soda): NaHCO 3



Sodium carbonate (soda): Na 2CO3

Select a substance to counteract and absorb the leaking electrolyte according to the instructions of the battery manufacturer.

1.1.5 Working at Heights

Avoid Avoid object falling when you work at heights. When working at heights, fulfill the following requirements: 

Issue 06 (2013-07-23)

Only trained personnel can work at heights.


6





Prevent the devices and tools that you carry from falling down.



Take safety and protection measures, for example, wear a helm and safety belt.



Wear warm clothes when working at heights in a cold region.



Before working at heights, check that all the lifting facilities are in good condition.

1.1.6 Using Ladders Checking a Ladder 

Before using a ladder, check whether the ladder is damaged. Only the ladder in good condition can be used.



Before using a ladder, ladder, you should know the maximum weight capacity of the ladder. Avoid overweighing the ladder.

Placing a Ladder The recommended gradient of ladders is 75 degrees. You You can measure the gradient of the ladder with an angle square or your arms. When using a ladder, ladder, ensure that the wider feet of the ladder are downward, or take protection measures for the ladder feet to prevent the ladder from sliding. Ensure that the ladder is placed securely. securely.

Climbing Up a Ladder When climbing up a ladder, note the following: 

Ensure that the center of gravity of your body does not deviate from the edges of the two long sides.



To minimize the risk of falling, hold your balance on the ladder before any operation.



Do not climb higher than the fourth rung of the ladder (counted from up to down).



If you want to climb up a roof, ensure that the ladder top is at least one meter higher than the roof.

1.1.7 Mechanical Safety Drilling Holes

Do not drill the cabinet at will. Drilling holes without complying with the requirements affects affects the electromagnetic shielding performance of the cabinet and damages the cables inside the cabinet. In addition, if the scraps caused by drilling enter the cabinet, the printed circuit boards (PCBs) may be short circuited. 

Before you drill a hole in the cabinet, wear insulated gloves and remove the internal cables from the cabinet.



Wear an eye protector when drilling holes. This is to prevent your eyes from being injured by the splashing metal scraps.



Ensure that the scraps caused by drilling do not enter the cabinet.

Issue 06 (2013-07-23)


7





Drilling holes without complying with the requirements affects affects the electromagnetic shielding performance of the cabinet.



After drilling, clean the metal scraps immediately. immediately.

Sharp Objects

Before you hold or carry a device, wear protective gloves to avoid getting injured by sharp edges of the device.

Handling Fans When handling fans, note the following: 

When replacing a component, place the component, screws, and tools in a safe place. Otherwise, if any of them fall into the operating fans, the fans may be damaged.



When replacing a component near fans, do not insert your fingers or boards into the operating fans until the fans are switched off and stops running.

Lifting Heavy Objects

When heavy objects are being lifted, do not stand or walk under the cantilever or the lifted object.

1.1.8 Bundling Signal Cables



Do not bundle signal cables with high current cables or high voltage cables.



Maintain a minimum space of 150 mm between adjacent ties.

Issue 06 (2013-07-23)


8



1.2 Equipment Safety 1.2.1 Electricity Safety High Electrical Leakage

If the "high electrical leakage" tag is present on the power terminal of the device, you must ground the device before powering it on.

1.2.2 Electrostatic Discharge

The static electricity generated by human bodies may damage the electrostatic-sensitive electrostatic-sensitive components on boards, for example, the large-scale integrated (LSI) circuits. Human body movement, friction between human bodies and clothes, friction between shoes and floors, or handling of plastic articles causes static electromagnetic fields on human bodies. These static electromagnetic fields cannot be eliminated until the static is discharged. To prevent electrostatic-sensitive electrostatic-sensitive components from being damaged by the static on human bodies, you must wear a well-grounded ESD wrist wrist strap when touching the device device or handling boards or application-specific application-specific integrated circuits circuits (ASICs). Figure 1-1 shows how to wear an ESD wrist strap. Figure 1-1 Wearing an ESD wrist strap

Issue 06 (2013-07-23)


9



1.2.3 Laying Cables When the temperature is very low, low, violent strike or vibration may damage the cable sheathing. To ensure safety, safety, comply with the following requirements: 

Cables can be laid or installed only when the temperature is higher than 0 ºC.



Before laying cables which have been stored in a temperature lower than 0 ºC, move the cables to an environment of the ambient temperature and store them at the ambient temperature for at least 24 hours.



Handle cables with caution, especially at a low temperature. Do not drop the cables directly from the vehicle.

Issue 06 (2013-07-23)


10


2 Installation Preparations

2

Installation Preparations

2.1 Tools Table 2-1 shows the tools that must be obtained before installation. Table 2-1 Tools

Combination spanner

Marker pen

Rubber hammer

Socket spanner

Wire clippers

Hydraulic pliers

Adjustable spanner

Paper knife

RJ-45.connect or crimping pliers

Issue 06 (2013-07-23)

Phillips screwdriver

Flathead screwdriver

Torque spanner

Diagonal plier

Network cable pliers

Sharp-nose pliers

Wire stripper

Power cable cutting pliers

Power cable crimping pliers

Crimping pliers

ESD-preventiv ESD-preventiv e wrist strap

Percussion drill

Drill bit

Clamp meter

Hot air dun

Steel tape

Vacuum cleaner

Multimeter

Antistatic gloves

Protective gloves


11



2.2 Installation Clearance Requirements Figure 2-1 shows the installation clearance requirements. Figure 2-1 Installation clearance requirements

2.3 Prepare Cables Table 2-2 lists the specification of the system cables. Table 2-2 The specification of the system cables

Cable

Cable Diameter and Color

Signal cables to dry contacts, Boolean values, and sensor ports

Not provided

RS485, RS232 or Fast Ethernet (FE) cable

Not provided

DC Power cable to the primary load

Not provided

DC Power cable to the secondary load

Not provided

The PGND cable

Cross-sectional area: 16 mm (0.02 in. )

2

2

Color: yellow green cable AC input power cable

2

single-phase: Cross-sectional area: 25 mm (0.04 2 in. ) 2

2

three-phase: Cross-sectional Cross-sectional area: 16 mm (0.02 in. )

Issue 06 (2013-07-23)


12


Cable


Cable Diameter and Color (recommended /Not provided)

Cut cables to a length suitable for the actual cable route, and then add OT terminals or cord end terminals to each end of the cables, as shown in Figure in Figure 2-2, Figure 2-3. Figure 2-2 Prepare OT terminals

Figure 2-3 Prepare cord end terminals.

NOTE

Issue 06 (2013-07-23)



The local cable colors prevail. The cable colors in the figure are for reference only.



Cables routed along the floor should be protected with protection tubes that comply with NFPA70 standards.


13


3 Configuration

3

Configuration

Specifications Table 3-1 Specifications

Category

Specifications

Dimensions (H x W x D)



Cabinet: 1500 mm (59.06 in.) x 650 mm (25.59 in.) x 650 mm (25.59 in.)



Base: 100 mm (3.94 in.) x 650 mm (25.59 in.) x 650 mm (25.59 in.)

Weight

Issue 06 (2013-07-23)

120 kg (264.6 lb) (without rectifiers or storage batteries)


14


3 Configuration

Interior of the Cabinet Figure 3-1 Interior of the TP48200A-D15A1

(1) Maintenance socket (4) Cable hole (7) Site monitoring monitoring unit (SMU)

Issue 06 (2013-07-23)

(2) AC input circuit breakers (5) Storage battery circuit breakers (8) Space for rectifiers


(3) Ground bar (6) Load circuit breakers (9) Battery rack

15


3 Configuration

Figure 3-2 Interior of the TP48200A- H15A3

(1) Maintenance socket (4) Cable hole (7) Site monitoring monitoring unit (SMU)

Issue 06 (2013-07-23)



(3) Ground bar (6) Load circuit breakers (9) Battery rack

16


3 Configuration

Figure 3-3 Interior of the TP48200A-H15A5

(1) Maintenance socket (4) Cable hole (7) Site monitoring monitoring unit (SMU) (10) Battery rack

Issue 06 (2013-07-23)



(3) Ground bar (6) Load circuit breakers (9) Heater

17


4 Installing the Cabinet

4

Installing the Cabinet

To install a cabinet, perform the following steps:

Step 1 Remove the cover of the packaging box and locate the marking-off template on the cover interior, as shown in Figure in Figure 4-1. Figure 4-1 Marking-off template

Step 2 Fix the installation hole, as shown in Figure in Figure 4-2. Figure 4-2 Fixing the installation hole

(1) Marker

(2) Marking-off template

(3) Installation Installat ion hole

(4) Concrete pad

Issue 06 (2013-07-23)


18



in Figure 4-3. Step 3 Drill holes and install expansion sleeves, as shown in Figure Figure 4-3 Drilling holes and install expansion sleeves

(1) Expansion bolt(M12) (5) Concrete pad

(2) Spring washer

(3) Flat washer

(4) Expansion sleeve

Step 4 Remove the cabinet from the pallet, as shown in Figure in Figure 4-4. Figure 4-4 Removing the cabinet

(1) Pallet NOTE

The configuration prevail, the pallet in the figure is for reference only

Step 5 Secure the cabinet on the concrete pad, as shown in Figure 4-5.

Issue 06 (2013-07-23)


19



Figure 4-5 Securing the cabinet

----End

Issue 06 (2013-07-23)


20


5 Installing a PGND Cable

5

Installing a PGND Cable

The PGND cable is used to connect PGND screws on the cabinet and the ground busbar outside the cabinet to ensure proper grounding of the cabinet. Install the PGND cable as shown in Figure in Figure 5-1. Figure 5-1 Installing the PGND cable

(1) Ground bar for the site

Issue 06 (2013-07-23)

(2) Ground bar for the cabinet


21


6 Installing Components

6

Installing Components

6.1 Installing Rectifiers The rated output current of each rectifier is 50 A. The number of rectifiers depends on actual capacity requirements.as shown in Figure in Figure 6-1 and Figure and Figure 6-2. Figure 6-1 Removing the filler panel

Figure 6-2 Installing rectifiers

Issue 06 (2013-07-23)


22



6.2 Installing a Smoke Sensor(Optional) 6.2.1 Securing the Smoke Sensor Secure the smoke sensor base to the cabinet top using two M4 mm screws and fasten the smoke sensor to the base based on the direction shown in the smoke sensor, as shown in Figure 6-3. Figure 6-3 Installing a Smoke Sensor

6.2.2 Connecting the Smoke Sensor Connect one end of the smoke sensor s ignal cable to the "SMOKE" port on the UIM02C and the other end to the port on the smoke sensor, as shown in Figure in Figure 6-4. Figure 6-4 Connect the smoke sensor

Issue 06 (2013-07-23)


23



6.3 Installing a Temperature and Humidity Sensor(Optional) 6.3.1 Securing the Temperature and Humidity Sensor Secure the temperature and humidity sensor base to the cabinet top, as s hown in Figure in Figure 6-5.

Step 1 Secure the temperature and humidity sensor base to the cabinet top using two M4 mm screws. Step 2 Connect and secure signal cables of the temperature and humidity sensor to the cabinet base, as shown in the following figure

Step 3 Install the top cover of the temperature and humidity sensor to the cabinet base. Step 4 The final installation view is as follows. Figure 6-5 Installing a temperature and humidity sensor

----End

6.3.2 Connecting the Temperature and Humidity Sensor Connect one end of the temperature and humidity sensor signal cable to the "TEM-HUM" port on the UIM02C and the other end to the port on the temperature temperature and humidity humidity sensor, as shown in Figure in Figure 6-6.

Issue 06 (2013-07-23)


24



Figure 6-6 Connecting the temperature and humidity sensor

6.4 Installing a Water Sensor(Optional) 6.4.1 Securing the Water Sensor Secure the water sensor to the cabinet bottom using cable ties, as shown in Figure in Figure 6-7. Figure 6-7 Installing a Water Sensor

6.4.2 Connecting the Water Sensor Connect one end of the water sensor signal cable to the "WATER" port on the UIM02C, as shown in Figure in Figure 6-8

Issue 06 (2013-07-23)


25



Figure 6-8 Connecting the water sensor

Issue 06 (2013-07-23)


26


7 Installing Cables

7

Installing Cables

7.1 Installing Signal Cables and Communication Cables 7.1.1 UIM02C NOTE

All ports in this manual are protected by a security mechanism.

The user interface module (UIM02C) supports eight dry contact outputs, nine Boolean value inputs (including general DI1-6, smoke, water, door status), three analog signals inputs (ambient temperature, humidity, and battery temperature).

Appearance Figure 7-1 UIM02C panel

Port Description Table 7-1 UIM02C port description

Port Type

Silkscreen

Description

Default Mode

Sensor ports

TEM_HUM

Temperature and humidity sensor

-

WATER

Water sensor

-

TEMP1

Connected to environment temperature sensor and used for fan speed adjustment

-

Issue 06 (2013-07-23)


27


Port Type

Boolean value input ports

7 Installing Cables

Silkscreen

Description

Default Mode

TEMP2

Reserved

-

GATE

Door status sensor

-

SMOKE

Smoke sensor

-

BTEMP

Battery temperature sensor

-

DIN1

Boolean value input 1

Close: alarm Open: normal

DIN2



DIN3



DIN4



DIN5


Open: alarm Close: normal

DIN6



Dry contact output ports Default mode (Close: alarm; Open: normal) can be modified as required.

ALM1

AC power failure alarm


ALM2

ALM3

ALM4

DC undervoltage alarm or DC overvoltage alarm Rectifier faults, Protect and No Response alarm SPD failure alarm

Close: alarm Open: normal Close: alarm Open: normal Close: alarm Open: normal

ALM5

Fuse burn-out alarm


ALM6

ALM7

Battery or environment temperature alarms

Open: normal

Door alarms

Close: alarm

Close: alarm

Open: normal ALM8

Communic ation Port

Issue 06 (2013-07-23)

COM

Heater faults alarms and Fan faults alarms


RS485


28


7 Installing Cables

7.1.2 Installing Dry Contacts and Boolean Values Signal Cables Install dry contacts and Boolean values signal cables , as shown in Figure in Figure 7-2. Figure 7-2 Installing dry contacts and Boolean values signal cables

(1) White Contact plate

(2) Dry contact

7.1.3 Installing Sensor Cables Connect the sensor cable to the corresponding ports on UIM02C. The pin definitions of the sensor ports refer to Figure to Figure 7-3 and Table and Table 7-2. Figure 7-3 Pins of sensor ports

Table 7-2 Pin Definition

Silk Screen

Pin

Pin definition

WATER

1

12 V

2

WATER

3

GND

4

-

1

12 V

2

ENV_TEMP

TEMHUM

Issue 06 (2013-07-23)


29


TEMP1

TEMP2

GATE

SMOKE

BTEMP

7 Installing Cables

3

12 V

4

ENV_HUM

1

TEMP1

2

GND

1

TEMP2

2

GND

1

DIN7+

2

JTD7

1

12 V

2

Smoke

1

Btemp1

2

12 V

7.1.4 Installing Communications Cables When in-band monitoring is required, connect the RS485/RS232 port on the SMU to the communications equipment over a cable with an RJ45 connector, when out-of-band monitoring is required, connect the FE port on the SMU to the communications equipment over a cable with an RJ45 connector, as shown in Figure in Figure 7-4. Figure 7-4 Port on the SMU

7.2 Installing Power Cables

Issue 06 (2013-07-23)


30


7 Installing Cables

CAUTION 

Before installing power cables, ensure that all circuit breakers to the OFF position.



Do not bind the ground cable, AC power cables, DC power cales, signal cables, and communications cable together. together.

Open the panel of power distribution unit, as shown in Figure in Figure 7-5. Figure 7-5 Open the panel of power distribution unit

7.2.1 Installing DC Output Cables Install DC output cables, as shown in Figure in Figure 7-6

Issue 06 (2013-07-23)


31


7 Installing Cables

Figure 7-6 Installing DC output cables

7.2.2 Installing Storage Batteries and Copper Bars



Before installing storage batteries, ensure that the circuit breakers of the storage batteries to the OFF position.



During the installation, avoid short circuits or reverse connections between the positive and negative poles of the storage batteries. All the tools used, such as a screwdriver, screwdriver, must be insulated to prevent the the storage batteries from from being burned and to ensure ensure personal safety.

Step 1 Installing the storage batteries, as shown in Figure in Figure 7-7.

Issue 06 (2013-07-23)


32


7 Installing Cables

Figure 7-7 Installing two layer storage batteries

Install the copper bar, as shown in Figure in Figure 7-8. Figure 7-8 Installing the copper bar

Step 2 Installing the power the power cables for for storage batteries, as as show in Figure in Figure 7-9.

CAUTION Connect negative power cables and then positive power cables for the batteries.

Issue 06 (2013-07-23)


33


7 Installing Cables

the powerr cable cabless for for stora storage ge batte batterie riess Figure 7-9 Installing the powe

----End

7.2.3 Installing AC Output Cables Install AC output cables, as shown in Figure in Figure 7-10.

Issue 06 (2013-07-23)


34


7 Installing Cables

Figure 7-10 Installing AC output cables

7.2.4 Installing AC Input Cables Install three-phase AC input cables refer to Figure to Figure 7-11.

Issue 06 (2013-07-23)


35


7 Installing Cables

Figure 7-11 Installing three-phase AC input cables

Install single-phase AC input cables, remove the copper bar from the cable bridge on the side panel and connect the copper bar to the AC input circuit breaker to short-circuit the breaker breaker,, as shown in Figure in Figure 7-12.

Issue 06 (2013-07-23)


36


7 Installing Cables

Figure 7-12 Installing single-phase AC input cables

Recover the panel of power distribution unit, as shown in Figure in Figure 7-13. Figure 7-13 Recover the panel of power distribution unit.

Issue 06 (2013-07-23)


37


8 System Commissioning

8

System Commissioning

8.1 Installation Verification After installation, verify that:

Step 1 The cabinet is installed properly and the cables are connected properly. (Cables fastened by screws are not easily removable.)

Step 2 Cables are arranged neatly and bound properly by using cable ties. Step 3 The storage battery is connected properly. Step 4 Check for short circuits between the live wires, between the live wire and the ground cable, between the live wire wire and the neutral wire, wire, between the RTN+ and the – the – 48 48 V busbar. Rectify short circuits before powering on the power system. ----End

8.2 Powering On and Commissioning 8.2.1 Setting Parameters Figure 8-1 SMU panel

Issue 06 (2013-07-23)


38



(1) Running status indicator

(2) Minor alarm indicator

(3) Major alarm indicator

(4) Liquid crystal display (LCD)

(5) FE

(6) Locking latch

(7) Four buttons

(8) USB (Reserved)

(9) RS485/RS232

(10) Hold hands

NOTE

If the Run indicator (green) on the SMU panel is blinking and the LCD is on, the SMU is powered on successfully.

Button Description Button description of SMU panel as shown in Table in Table 8-1 Table 8-1 Button description of SMU panel

Button

Name

Description Descripti on

“▲”or “▼”

“up” up”or ”down” down”

Allows you to view menu items and set the value of a menu item by pressing ▲ or ▼.

“Cancel”

Returns to the previous menu without saving the settings of the current menu item.

“Enter ”

Enters the main menu from the standby screen, enters a submenu from the main menu, or saves the settings of a submenu item.

“

”

“

”

Remark : 

After a menu is displayed, the standby screen is displayed and the LCD screen becomes dark if you you do not press any button within 5 minutes. minutes.



You need to log in again if you do not press any button with 8 minutes.



The preset username is admin and the preset password is 001.

Setting Parameters Step 1 Measure the voltage across the input ports of AC input circuit breakers. The voltage must range from 200 V to 240 V. The rated voltage is 220 V. If not, ask professionals to rectify the fault.

Step 2 Switch the AC input circuit breaker to the ON position, measure the voltage between L wiring and N wiring terminal. The voltage must range from 200 V to 240 V. The rated voltage is 220 V.

Step 3 Set the NetEco Main IP, NetEco Bak IP, NetEco Port, LUI Language and Set Time Zone according to actual conditions.

Issue 06 (2013-07-23)


39



Step 4 Set the Qty of Battery, Rated Capacity, Set Date and Set Time according to actual conditions. (Always set Qty of Battery to 1 and set Rated Capacity to the total capacity of all battery strings.)

Step 5 Set the IP Address, Subnet Mask and Default Gateway according to actual conditions. Table 8-2 Parameter settings

Main Menu

Second-Level Menu

Third-Level Menu

Fourth-Level Menu

Default Value

Settings

Comm Para

NetEco Main IP

-

-

NetEco Bak IP

-

-

NetEco Port

-

31220

System Para

Quick Settings

Host Comm Addr

0

Comm Baudrate

9600

LUI Language

-

ENGLISH

Set Time Zone

-

GMT +08:00

Qty of Battery

-

-

1

Rated Capacity

-

-

150Ah

Set Date

-

-

-

Set Time

-

-

-

IP Address

-

-

192.168.0.10

Subnet Mask

-

-

255.255.255.0

Default Gateway

-

-

192.168.0.1

Step 6 Set battery fuse break alarm " Enable/Disable" status. ----End Table 8-3 Battery fuse break alarm "Enable/Disable" status

Main Menu

Second-Level Menu

Third-Level Menu

Fourth-Level Menu

Set Value

Settings

Alarm Setting

Site Summary

Battery Fuse1 Break

Enable battery fuse blown alarms for the branches with batteries, and disable battery fuse blown alarms for the branches

Battery Fuse2 Break Battery Fuse3 Break Battery Fuse4 Break Battery Fuse5 Break

Issue 06 (2013-07-23)


40


Main Menu


Second-Level Menu

Third-Level Menu

Fourth-Level Menu

Set Value

Battery Fuse6 Break

without batteries.

Battery Fuse7 Break Battery Fuse8 Break Battery Fuse9 Break Battery Fuse10 Break Battery Fuse11 Break Battery Fuse12 Break NOTE

You can set parameters to modify the default mode of the Boolean value input ports and the dry contact output ports, as shown in Table in Table 8-4.

Table 8-4 Modify the default mode of the Boolean value input ports and the dry contact output ports ports

Main Menu

Second-Level Menu

Third-Level Menu

Default Value

Settings

Site Summary

DI1Alarm

Close

DI2 Alarm

Close

DI3 Alarm

Close

DI4 Alarm

Close

DI5 Alarm

Open

DI6 Alarm

Close

DO1 Alarm Act

Close

DO2 Alarm Act

Close

DO3 Alarm Act

Close

DO4 Alarm Act

Close

DO5 Alarm Act

Close

DO6 Alarm Act

Close

DO7 Alarm Act

Close

DO8 Alarm Act

Close

NOTE

You can set parameters to modify the related relay of the alarm. For example, set Battery1 Lost to DO8, as shown in Table in Table 8-5.

Issue 06 (2013-07-23)


41



Table 8-5 Set Battery1 Lost to DO8

Main Menu

Second-Level Third-Level Fourth-Level Menu Menu Menu

Default Value

Set Value

Settings

Alarm Setting

None

DO8

Batt Summ

Battery1 Lost

8.3 Powering On

CAUTION To avoid damaging storage batteries, batteries, switch the battery circuit breaker to the ON positions only after correctly setting the storage battery parameters on the SMU. Switch the AC input circuit breakers to the OFF positions.

Step 1 Reinstall the removed copper bar or cable of the s torage battery. Step 2 Switch the storage battery circuit breakers in the PDU to the ON positions. Step 3 Switch the AC input circuit breakers to the ON positions. Check whether the voltage between the RTN+ busbar and DC output terminal are the same as the storage battery voltage and the voltage displayed on the monitoring unit. If not, ask professionals to rectify the fault.

Step 4 Switch the LLVD and BLVD branches to the ON positions, measure whether the voltage between RTN+ and the DC output terminal. The voltage voltage must range from 42 V to 58 V (without load). The rated voltage is 53.5 V. Check whether the loads work normally. If the loads work abnormally, rectify the fault according to the relevant user guides.

Step 5 Switch the circuit breakers for the Maintenance socket, AC input, battery route, BLVD switch, and LLVD switch as required.

Step 6 Check whether the element management system (EMS) can receive the information from the power system. If not, check check whether the IP IP address is set correctly. correctly.

Step 7 Observe the operation of the power system for 15 minutes. If no alarms (except for door alarm) are generated, and current/voltage parameters of the storage battery and loads are set properly, then re-install the cover of the distribution unit, lock the door to the cabinet, give the key of the cabinet door to the customer, and clean the site before leaving.

CAUTION 

To make the system run properly, properly, flip the switch to the Normal position.



To power on the battery forcibly, flip the switch to the BAT On position.

Issue 06 (2013-07-23)


42



----End

Issue 06 (2013-07-23)


43

TP48200A-D15A1 & H15A3 & H15A5 V300R001 Quick Installation Guide 06

Recommend Documents