Page 1/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Warnings and recommendations Unless otherwise advised by the manufacturer, the f ollowing procedures are recommended: Always fit a new timing belt after removal Check the tensioner and idler pulleys; renew if necessary Never turn the engine in the direction opposite to that of normal operation Inspect the belt(s) for cracks, fraying, wear and oil contamination Note: The engine must be cold before timing belt adjustment Note: Avoid bending, torsion or traction
General Always check the timing timing marks before timing timing belt removal
Before disconnecting the battery cable, check the audio system security code
Removal Disconnect the battery Remove the air filter and the air-inlet hose Remove the engine upper cover Remove the engine lower cover Remove the air-conditioner belt ©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 2/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Remove the alternator belt Remove the timing belt upper cover
Turn the crankshaft to TDC for cylinder 1
Remove the crankshaft pulley,
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 3/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Fit the crankshaft TDC positioning tool from under the engine into the flywheel, Mot. 1054
Turn the crankshaft until the locking pin fits, Lock the injection pump gearwheel with a locking pin, Mot. 910
Lock the injection pump shaft, :
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 4/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Remove the bolt
Remove the spacer Refit the bolt Compress the tensioner Lock the tensioner, Use a modified nut (U-shape), M14
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 5/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Remove the timing belt lower cover
Remove the tensioner pulley, Remove the timing belt Remove the idler pulley
Installation Fit the idler pulley, 41 Nm Fit the tensioner pulley Fit the timing belt Fit the timing belt lower cover, 8 Nm
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 6/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Fit the crankshaft pulley
Remove the injection pump locking pin, Mot. 910
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 7/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Remove the crankshaft locking pin, Mot. 1054
Unlock the injection pump shaft, : Loosen the bolt Fit the spacer
Tighten the bolt
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 8/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Remove the tensioner locking tool, M14
Rotate the engine 2 rotations by hand, Fit the crankshaft TDC positioning tool from under the engine into the flywheel, Mot. 1054 Fit the injection pump locking pin, Mot. 910 Tighten the crankshaft pulley, 30 Nm Tighten the tensioner pulley nut, 41 Nm Remove the locking pins, Mot. 910, Mot. 1054 Fit the flywheel locking tool, Mot. 1054 Tighten the crankshaft pulley, 200 Nm Refit the flywheel cover plate
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 9/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Fit the timing belt upper cover
Fit the alternator belt Turn the engine 3 rotations clockwise Check the tension with a tension gauge, Mot. 1273
The tension is set when the tension gauge indicates a value of:, 292 ± 10 Hz Tighten the alternator Fit the air-conditioner belt Check the tension with a tension gauge, Mot. 1273 The tension is set when the tension gauge indicates a value of:, 130 ± 6 Hz Fit the engine lower cover Refit the engine cover Refit the air filter housing and hoses Reconnect the battery
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI
Page 10/10
RENAULT Master II 2.8 dTi (S9W-702) 1998 until 2003
Timing Torque settings Crankshaft pulley:, 200 Nm Tensioner pulley:, 41 Nm Idler pulley:, 41 Nm
Special tools Crankshaft locking pin:, Mot. 1054 Injection pump locking pin:, KM-910 Tension gauge:, Mot. 1273
©Vivid Automotive Data & Media B.V.
Powered by Vivid WorkshopData ATI