Sandblasting

SAFE WORK PROCEDURE Division:

Analysis By:

Department:

Supervisor:

 Job Title:

Auto Body Metal

 Job Title:

Sad!la"t#$ Ca!#et

Approved By:  Job Performed Performed By: By:

Date:

Sep/12/2006

Frequency:

Hourly

JSA Number: %ea&'er ad or "tudet"

RE(U)RED PERSO*A+ PRO%EC%),E E(U)PME*% - CSA approved safety bootss!oes" CSA approved safety #lasses#o##les" !earin# protection" $%%& cotton coveralls pre(approval to operate t!is .E*ERA+ *O%ES- 'perators must be trained by a teac!er" demonstrate competency and receive pre(approval equipment" by t!e teac!ers of t!e Auto Body )etal s!op or Automotive Tec!nolo#y s!op* No matc!es" li#!ters or cell p!ones allo+ed in t!e s!op area* ,on# !air s!ould be tied bac-. strin#s and !oods from pulloverss+eaters s!ould be removed or tuc-ed inside of coveralls* ,on# nec-laces and or bracelets s!ould be removed*

 OB SAFE% A*A+ A*A+S)SS)SSt e p

De"&r#pt#o

Haard

Cotrol"

$

Pre( op operation +a +al- ar around in inspection of of sand(((blaster and surroundin# area*(( Sandblaster side door s+in# s!ould be clear of obstructions* /nsure t!at t!e side door closes properly and t!at t!e latc! secures door ti#!t*

a0 'peration in1urin# yourself or ((b0 'peration in1urin# ot!ers((c0 Slip around mac!ine area*

a0 2 b0 3emove any obstructive material from door s+in# area*((c0 Clean up sand from 4oor area to reduce slippa#e*((/nsure t!at t!e equipment is not dama#e ( if dama#ed do not use" notify teac!er ri#!t a+ay*

5

a0 C!ec- for e6!aust fan operation* 78n t!e Auto Tec!nolo#y s!op you must attac! an e6!aust !ose to t!e !ose of t!e sand blaster0*((B0 C!ec- for cabinet li#!t operation*((c0 operation*(( c0 C!ec- #lass for abrasive areas*((

a0 Dust in!alation((b0 9isibility

a0 Contact a teac!er immediately if e6!aust fan fails to start(up*((b0 Contact teac!er and report an inoperative interior li#!t*((c0 8f t!e cabinet inspection #lass !as been eroded" as- a teac!er to assist +it! its replacement or as- teac!er to !ave it replaced*



a0 'p 'pen do doors an and in inspect do door se seals*((b0 8nspect bead #un for proper #roundin#*(( c0 8nspect #loves to ma-e sure t!ey are not torn or ripped*

a0 ,ea-a#e onto 4oor ( slips((b0 /lectrical static s!oc-((c0 Sand penetratin# s-in ( abrasion

a0 3eseal lea-in# door((b0 3epair #round on bead #un((c0 3eplace #loves((

Pa#e $ of 5

Print Date: Sep$55%%;

<

8f sandblaster passes all inspections and everyt!in# is in #ood +or-in# order* ((Turn on li#!t" ensure bot! doors are sealed and secure" place !ands in #loves !old bead #un +it! one !and and +it! t!e ot!er !and !old +!at you are blastin#* Press do+n on foot pedal +it! foot" a mi6ture of air and sand +ill be forced t!rou#! t!e bead #un* Continue sandblastin# until you are satis=ed" 1ob completed*

Doors not sealed and secured ( dust in!alation" lea-a#e onto 4oor ( slips*

)a-e sure doors are sealed and secure*

>

3emove foot from foot pedal" and +ait until dust !as settled before openin# top door or side door to remove your +or-* 'nce +or- is removed" re(latc! doors* ((S!ut o? li#!t" 7disconnect e6!aust !ose( auto tec! only0* Clean up any sand t!at !as fallen around sandblaster*

Dust in!alation((Slip around mac!ine area

@ait until dust !as settled before removin# your +or-*((Clean up area of any sand t!at !as fallen around sandblaster*

AU%HOR)ED EMP+OEE )*FORMA%)O*)D *UMBER-

+AS% *AME-

F)RS% *AME-

REMARKS-

 OB H)S%OR )*FORMA%)O*DA%E-

REMARKS-

Approval Si#nature:

Date:

Pa#e 5 of 5

Print Date: Sep$55%%;