Edition: 01
Date: 13/10/2014
PROCEDIMENTO PARA ACESSO RADIO MPR-E FULL OUTDOOR
1
OBJETIVO Este procedimento busca auxiliar o acesso via Craft Terminal, ao radio 9500MPR-e Full Outdoor, quando instalado com a IDU - Power Injector Box ou MPT Power Unit.
2
REFERENCIAS DA IDU
POWER INJECTOR BOX Power Injector box: box: stand-alone box, powered through two connectors on the front providing power supply redundancy. The box can be mounted in a rack by means of a separate bracket. The bracket supports one or two boxes (1.3U).
Figure 1 Power Injector box Connectors . Two DC connectors in the front (for box version), or power from the backpanel (for plug-in version). User Manual Product information and planning 9500 MPR for ETSI RELEASE 4.2.0 168 /1232 3DB19901ACAA Issue 01
. Two RJ45 for the data in (DATA) . Two RJ45 for the data + DC out (DC+DATA) LEDs . Two LEDs indicate the presence of DC voltage on each Ethernet output.
Figure 2 Power Injector front panel Note: Note: The power source "battery" is isolated from AC power main feeds. A 2-wire power cable (2x1 mm2 - AWG17) is supplied (1AC007800068). Note: Note: Power cable gauge smaller than 2x1 mm2 (AWG 17) is not allowed for proper operation of the Power Injector box. The blue wire must be connected to -48 Vdc (live); the black wire to + (Return). The cable must be screwed to the Power Injector box and to the battery. Note: Note: The Power supply must be connected to a fuse or a breaker on a customer power distribution box. The recommended value is 3 Amps for one ODU and 6 Amps for two ODU
Responsável: Eng. Flavio Hirano Hirano
Edition: 01
Date: 13/10/2014
Figure 3 Power Injector with ODU
MPT Power Unit The MPT power unit is an indoor device, which provides office power to up to four MPTs using coax cable and Type-N connectors The MPT power unit has 7 connectors: _ Battery A/B (A & B power from office power) _ MPT 1/4 (DC Power to MPT) _ Alarms (Alarm status)
Figure 4 MPT Power Unit front panel To power the ODU one mean, coaxial cable is connected to: _ MPT Power Unit (N Connector) _ N to Ethernet pair Pigtail (RJ45 of pair Pigtail is connected to RJ45 of MPT) For data transmission, optical fiber is connected to the IDU and the MPT using optical connectors.
Responsável: Eng. Flavio Hirano
Edition: 01
Date: 13/10/2014
OBSERVAÇÃO: PARA ACESSAR A ODU UTILIZANDO A IDU MPT POWER UNIT, SERÁ NECESSÁRIO TER EM MÃOS O CONVERSOR OPTICO PARA RJ45, OU UTILIZAR UMA PORTA RJ45 DO ROTEADOR.
Figure 5 MODELO CONVERSOR OPTICO (exemplo)
3
CRIANDO A VLAN 4080 (DEFAULT) NO LAPTOP
O primeiro passo é verificar se o Laptop cria VLAN na porta ETHERNET (RJ45), seguindo o passo a passo apresentando nas telas abaixo:
Responsável: Eng. Flavio Hirano
Edition: 01
Date: 13/10/2014
Caso não permita criar a VLAN, deve-se fazer a atualização do drive, de acordo com o fabricante do adaptador de rede. Feito o procedimento prosseguir com as configurações. Clicar em propriedades, configurar a VLAN 4080, conforme apresentado nas telas abaixo:
Responsável: Eng. Flavio Hirano
Edition: 01
Date: 13/10/2014
Responsável: Eng. Flavio Hirano
Edition: 01
Date: 13/10/2014
Colocar um IP na mesma classe da ODU que é 192.168.100.1 (default de fabrica), configurar na placa de rede por exemplo: IP: 192.168.100.200 (exemplo) Mask: 255.255.255.0 Gateway: 192.168.100.1 (default de fabrica)
Responsável: Eng. Flavio Hirano
Edition: 01
4
Date: 13/10/2014
ACESSANDO A ODU
Para acessar o ODU Stand Alone é necessário utilizar o MCT Craft, que está localizado na mesma pasta onde se encontra o NEtO. (WebEML) Pasta 9500MCT_V07.03.01. Criar um atalho do Ícone na área de trabalho, conforme as telas abaixo:
MCT
Responsável: Eng. Flavio Hirano
Edition: 01
Date: 13/10/2014
Aparecerá, esta mensagem abaixo, clicar em Accept > NEXT > (configuração OnLine)
Digitar o IP no campo Connect to 192.168.100.1 (Default Fabrica) Digitar o User name: admin Password: admin Clicar em Finish
Tela inicial do rádio sem configuração. Primeiramente configurar o tipo de proteção. Selecione o item Protection marque 1+0 (nesta versão só há esta possibilidade). Clique em Apply.
Edition: 01
Fazer as configurações na aba, radio, radio configuration.
Faça a Rota estática p/ que os demais elementos possam enxergar via TMN a ODU.
Date: 13/10/2014
Edition: 01
Date: 13/10/2014
Para o exemplo acima os Rádios da Rede eram todos com endereço IP 10.0.x.x . Níveis de PTx e PRx:
Responsável: Eng. Flavio Hirano
Edition: 01
Tx Power local
Date: 13/10/2014
Rx remoto
Tx Power local
Rx local
Tx Power local
RX TX Power remoto
Rx local
IP para acesso remoto
Edition: 01
Date: 13/10/2014
ATENÇÃO: AO TROCAR OS IPs, para colocar conforme a DCN da regional, TROCAR UM ITEM DE CADA VEZ, CONFORME A SEGUIR: 1) 2) 3) 4)
IP ADDRESS NE; IP ADDRESS TMN IN-BAND; MASK TMN IN-BAND; VLAN ID TMN IN-BAND.
E ANOTAR A NOVA CONFIGURAÇÃO, POIS SE PERDER TERÁ QUE ENVIAR A ODU PARA FABRICA RESETAR A CONFIGURAÇÃO DE IP E RECUPERAR O ACESSO A ODU.