Meditation Instructions by Kirpal Singh, Sant Mat Tradition (Published by Ruhani Satsang.)Full description
The Isis organization is revamping IslamFull description
Meditation Instructions by Kirpal Singh, Sant Mat Tradition (Published by Ruhani Satsang.)
Instrucciones
Descripción: rgdfgdfg
InstructionsFull description
Full description
Full description
Full description
Instrucciones de lubricacion
já é, dobrando o ryujinDescrição completa
spss
Instructions for reflashing a Toshiba Thrive A-100 or a-105.
site instructions
print
Full description
Descripción: Instructions on how to safely perform a firewalk, from a Physics teacher.
já é, dobrando o ryujin
Install Instructions
Instruction for EquiSync
PowerWand Instructions by Chrystalk
Page 1
PowerWand Instructions by Chrystalk
---Original message--From: "Chrystal Kay"
>Don's Power Wand > Parts List: 1- 3" copper pipe, 9" long 1- copper cap for pipe 1- dixie cup that will fit snugly in end http://www.ryanmcginty.com/orgone/pwinstructions.htm
25/01/2006 00:59:40
PowerWand Instructions by Chrystalk
Page 2
1- 7" by 1" dia SP crystal 1- roll blue magnet wire from Radio Shack 2- 2" drywall screws Shrink wrap tubing- op. 99" 18 gage bare wire tape Goop glue Metal filling- 1/2 copper at least, and aluminum Resin and catalyst 1- 1" Amethyst point 1/4tsp. Pyrite grains 4- 12mm Hematite beads 4 or 5- rough round Garnets Frequency box w/alligator clip connectors. Silicon spray ( or WD-40 )
Instructions:
Preparing large crystal:
Start at the bottom of the crystal. ( make the 'ears' that will stick out rather long- 2-3") Using magnet wire, make a six wrap mobius knot , and continue below that and make a second six wrap mobius knot. Continue to make a total of six- six wrap mobius knots from the same continuous piece of wire. ( look in Don's files to see how to twist the wire for the knot.)
Now attach 2- screws to 'ears' by firmly wrapping around threads and either http://www.ryanmcginty.com/orgone/pwinstructions.htm
25/01/2006 00:59:40
PowerWand Instructions by Chrystalk
Page 3
shrink wrap or goop glue well. ( no bare wire or screw length exposed) Leave only the head exposed. Tape to crystal to hold in place while pouring, head ends up beyond end of crystal.
With the entire length of bare wire, wrap the crystal from top to bottom counter clockwise. (there is a reason for that)
On to the assembly:
This project is made beginning with the TOP. Fit your Dixie cup into the top end of the pipe, (flat side in) and trim flush with rim. Cut x in bottom and insert point of large crystal, from the bottom of the cup, up.( Don does this so point will be below the rim of the pipe.) rim.
Glue well around crystal and glue cup in place flush with
Now turn over, bottom side up. Put just enough metal and resin in to cover cup and meeting place of crystal and cup bottom.
Let harden. (Less leaks this way!)
Add metal to position amethyst in.
Place amethyst point down next to
crystal pointing same way, and add catalyzed resin.( Let firm up between each layer.)
Add Hematite, add metal and pour on resin. You should be pretty close to the top by now...say 2 1/2" or so. Add Garnets, add metal to beneath top of screws.
Let cure.
Trim off any boo boos or leaks.
Attach frequency box clips to screw ends. The frequency box will fit handily into the cap. With some spray around the edge of the pipe rim, it shouldn't be too hard to remove the cap for changing the battery.