OmniBAS_ IDU_ Installation and Cabling_ Manual_en_ed 6.0

GDC-002/34

Next Generation Ethernet Microwave Backhaul Solution

Installation and Cabling Manual Edition 6.0 Confidential

The information contained in this document is subject to change without prior notice.

ã INTRACOM S.A. TELECOM SOLUTIONS, 2014. All rights reserved. All copyright, intellectual and industrial rights in this document and in the technical knowledge it contains are owned by INTRACOM S.A. TELECOM SOLUTIONS and/or their respective owners. This document is made available to the end users only for their internal use. No part of this document nor any data herein may be published, disclosed, copied, reproduced, redistributed by any form or means, electronically or mechanically, or used for any other purpose whatsoever without the prior written approval of INTRACOM S.A. TELECOM SOLUTIONS. Information as well as drawings and specifications contained in this document are subject to change without prior notice. All trademarks and copyrights mentioned herein are the property of INTRACOM S.A. TELECOM SOLUTIONS and/or their respective owners. Any rights not expressly granted herein are reserved. Printed in Greece.

INTRACOM TELECOM 19.7 km Markopoulou Ave., Peania, Athens, GR 19002 T +30 210 667 1000, F +30 210 667 1001 http://www.intracom-telecom.com email (product support): [email protected]

Document Revision History

OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0

Document Revision History Revisions

This page shows the main changes effected in relation to the previous edition of the OmniBASTM IDU Installation: Revisions

Reasons of change

Previous:

4.0 – 5.1

Current:

6.0

The table below shows the reasons for the document change effected in relation to the previous document edition. Chapter /

A (Added), M (Modified) or R (Removed)

Paragraph Introduction Overview of OmniBAS Product Family (page 2): • New unit added (OmniBASTM-4P). • New unit for OmniBASTM-4W.

M/A

Installation Material Installation materials for OmniBAS-4W/8W (page 10).

M

New installation materials for new unit OmniBAS-4P (page 14).

A

Before Starting the Installation New Power supply requirements (page 17) for new units OmniBASTM4W/4P. New Cabling Overview (page 20) for all units.

M/A M

Mechanical Installation New Chassis Overview (page 34) for new unit OmniBASTM-4W.

M

New unit added OmniBAS-4P (page 39).

A

Cabling Installation New unit added OmniBASTM-4P (page 55).

A TM

E1 Terminations (pages 60, 63, 66)–New unit added OmniBAS -4P.

A

Cable Characteristics New cable characteristics for new unit OmniBASTM-4P (pages 73 - 75).

A

Appendix-C: Receptacles Pin Out New receptacles pin-outs added for new unit OmniBASTM-4P (page 95)

A


(Page intentionally left blank)

Document Revision History


Table of Contents 1

Introduction ......................................................................................................................1 About this Document..........................................................................................................1 Overview of OmniBAS Product Family ..............................................................................2 Safety Precautions .............................................................................................................5

2

Installation Tools..............................................................................................................6

3

Installation Material..........................................................................................................7 OmniBAS-2W.....................................................................................................................7 OmniBAS-4W/8W ............................................................................................................10 OmniBAS-4P....................................................................................................................14

4

Before Starting the Installation.....................................................................................16

4.1

Installation Prerequisites ..................................................................................................16

4.2

Cabling Overview .............................................................................................................20 Modem Cabling ................................................................................................................21 RJ-45 Cabling (Ethernet Payload) ...................................................................................23 RJ-45 Cabling (Outband Management) ...........................................................................24 SFP Cabling (Ethernet Payload) ......................................................................................25 SFP Cabling (STM-1 Payload).........................................................................................26 E1 Cabling (Balanced 120 Ω) ..........................................................................................27 Power Supply Cabling......................................................................................................28 Other Cabling ...................................................................................................................29

5

Mechanical Installation..................................................................................................32

5.1

OmniBAS-2W...................................................................................................................32 Chassis Overview ............................................................................................................32 IDU Installation.................................................................................................................33

5.2


5.3


5.4

OmniBAS-4P....................................................................................................................39 Chassis Overview ............................................................................................................39 IDU Installation.................................................................................................................40

6

Cabling Installation ........................................................................................................42

6.1

Power Supply Cables.......................................................................................................43 Preparation ......................................................................................................................44 Installation ........................................................................................................................48

6.2

IF Tails .............................................................................................................................56

6.3

E1 Terminations ...............................................................................................................59 Open End Cables (Balanced 120 Ω)................................................................................59 I

Table of Contents

BNC Terminations (Unbalanced 75 Ω) ............................................................................62 RJ-45 Terminations (Balanced 120 Ω).............................................................................65 6.4

I/O Cables ........................................................................................................................68

6.5

Ethernet Cables ...............................................................................................................70

7

Cable Characteristics ....................................................................................................71

7.1

GbE Cable Characteristics...............................................................................................71 OmniBAS-2W...................................................................................................................71 OmniBAS-4W/8W ............................................................................................................72 OmniBAS-4P....................................................................................................................73

7.2

Fast Ethernet Cable Characteristics ................................................................................74 OmniBAS-2W...................................................................................................................74 OmniBAS-4W/8W ............................................................................................................74 OmniBAS-4P....................................................................................................................75

7.3

STM-1 Cable Characteristics ...........................................................................................76 OmniBAS-4W/8W ............................................................................................................76

Appendix-A: Modem Card Installation / Removal ..................................................................77 Appendix-B: I/O Connections ..................................................................................................80 Appendix-C: Receptacles Pin Out ...........................................................................................83 OmniBAS-2W...................................................................................................................83 OmniBAS-4W/8W ............................................................................................................89 OmniBAS-4P....................................................................................................................95 Appendix-D: Open End Cables Color Codes..........................................................................99

II

Equipment Disposal Disposal of old electrical and electronic equipment (applicable through the European Union and other European countries with separate waste collection systems). This symbol, found on this product and any of its parts or on its operating instructions or on its packaging, indicates that electrical and electronic equipment may not be disposed of as unsorted municipal waste. Instead, this product should be handed over to applicable collection points for the recycling of electrical and electronic equipment. By ensuring the correct disposal of this product, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. By recycling, reusing and other forms of recovery of old electrical and electronic equipment you are making an important contribution to the conservation of natural resources and to the protection of the environment. For more information about the recycling of this product, please contact your local municipal authorities, municipal waste disposal service or the store where you purchased this product.

Απόρριψη παλαιών ηλεκτρικών και ηλεκτρονικών συσκευών (ισχύει στην Ευρωπαϊκή Ένωση και άλλες Ευρωπαϊκές χώρες με συστήματα χωριστής συλλογής απορριμμάτων). Το σύμβολο αυτό, που απεικονίζεται πάνω στο προϊόν και σε τυχόν εξαρτήματα του ή στο εγχειρίδιο οδηγιών του ή στη συσκευασία του, δείχνει ότι οι ηλεκτρικές και ηλεκτρονικές συσκευές, μετά το πέρας της λειτουργίας τους, δεν θα πρέπει να απορρίπτονται μαζί με τα αστικά απόβλητα. Αντίθετα θα πρέπει να παραδίδονται σε κατάλληλα σημεία συλλογής για την ανακύκλωση των ηλεκτρικών και ηλεκτρονικών συσκευών. Διασφαλίζοντας τη σωστή απόρριψη αυτού του προϊόντος, συνεισφέρετε στην πρόληψη πιθανών αρνητικών συνεπειών στο περιβάλλον και την ανθρώπινη υγεία, οι οποίες θα μπορούσαν να προκληθούν από την μη ενδεδειγμένη απόρριψη του προϊόντος. Η ανακύκλωση, επαναχρησιμοποίηση και άλλες μορφές αξιοποίησης των παλαιών ηλεκτρικών και ηλεκτρονικών συσκευών βοηθούν στη διαφύλαξη των φυσικών πόρων και στην προστασία του περιβάλλοντος. Για περισσότερες πληροφορίες σχετικά την ανακύκλωση αυτού του προϊόντος, παρακαλούμε επικοινωνήστε με τις τοπικές δημοτικές αρχές, την υπηρεσία αποκομιδής αστικών αποβλήτων ή το κατάστημα από το οποίο αγοράσατε το συγκεκριμένο προϊόν. Για περισσότερες πληροφορίες, μπορείτε να επικοινωνείτε με το Συλλογικό Σύστημα Εναλλακτικής Διαχείρισης Αποβλήτων Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού “Ανακύκλωση Συσκευών Α.Ε.” (www.electrocycle.gr).

Declaration of Conformity Hereby, Intracom S.A. Telecom Solutions declares that the product OmniBAS is in compliance with the essential requirements and other relevant provisions of the directive 1999/5/EC, and with the requirements of the RoHS directive 2011/65/EU. For further information, please visit the following URL: http://emc.intracom-telecom.com/

Δήλωση Συμμόρφωσης Με την παρούσα, η Intracom Α.Ε. Τηλεπικοινωνιακών Λύσεων δηλώνει ότι το προϊόν OmniBAS συμμορφώνεται προς τις ουσιώδεις απαιτήσεις και τις λοιπές διατάξεις της οδηγίας 1999/5/EC, καθώς και με τις απαιτήσεις της οδηγίας RoHS 2011/65/EU. Για περισσότερες πληροφορίες γύρω από τη δήλωση συμμόρφωσης, παρακαλούμε επισκεφθείτε την κάτωθι ιστοσελίδα: http://emc.intracom-telecom.com/


1

Introduction

About this Document Scope of document

This document provides information concerning the installation and cabling of the following OmniBAS™ Indoor Units (IDUs) units: • • • •

Target Audience

This document is addressed to certified technicians with wireless equipment knowledge and skills concerning the following: • • • • • •

Reference Manuals

OmniBASTM-2W OmniBASTM-4W OmniBASTM-8W OmniBASTM-4P

Indoor Unit Installation (IDU). Addition / Removal of IDU Cards. Laying and Installation of Cables. Preparation & Termination of: Ethernet, E1, Power cables e.t.c Test & Measurement of cables (Ethernet, Optical, Power). Equipment Grounding to the Main Grounding System.

The following document for OmniBASTM IDU Installation can be used for additional product information and are available by Intracom S.A. Telecom Solutions: Item

Conventions

Description

1

OmniBAS_ODU_Installation Manual.

2

OSDR_Installation Manual.

This document applies the following conventions: This symbol means DANGER. The purpose of this symbol is to warn you that any wrong action can cause bodily injury or even death. This symbol means CAUTION. The purpose of this symbol is to prevent you from performing an action that might result in damage of the equipment. A note calls your attention to important supplementary information.

1

Chapter 1. Introduction

Overview of OmniBAS Product Family Introduction

The OmniBAS™ family of Intracom Telecom IP MW PtP portfolio comprises: • Split-mount systems: − OmniBAS™ Indoor Units (IDUs) 1RU / 2RU high and 19″ wide. − OmniBAS™ Outdoor Units (ODUs) & antenna systems. • All-outdoor system: − OmniBAS™ OSDR (Outdoor Software-Defined Radio) integrating everything (baseband / controller / modem / radio) into a robust enclosure. This document describes the installation of: • OmniBAS™ - 2W/4W/8W IDUs for Split-mount system. • OmniBAS™ - 4P IDU for All-outdoor system. Continued on next page

2


Overview of OmniBAS Product Family, Continued OmniBAS™ IDUs

The OmniBAS™ Indoor Units (IDUs) are shown below: Indoor Unit (IDU)

Description It is a Native-IP, 1RU unit accommodating up to two modems. It can be positioned at the edge of the network, or can be used as a repeater and even as a ring node.

OmniBAS™-2W

Interfaces: • 2 x GbE (electrical) & 2 x GbE (electrical or SFP) (1) • - / 16 x E1 It is a Native-IP, highly-modular 1RU indoor unit and is capable of accommodating in the same chassis the following cards (identical with OmniBASTM-8W): • a combination of 4 modem cards • one interface card • one controller card

OmniBAS™-4W

Modem cards can be flexibly chosen based on the connection type to the outdoor unit: • radio connection to an ODU using coaxial IF cable • PonE connection to an all-outdoor unit (i.e OmniBAS™ OSDR) system using Ethernet cable Interfaces: • 2 x GbE (electrical) & 4 x GbE (SFP) • - / 16 / 32 x E1 2 / 4 x STM-1 (VC-12) Continued on next page

(1)

When Dual Media SFPs are installed, then only two out of four electrical GbE interfaces can be used.

3

Chapter 1. Introduction

Overview of OmniBAS Product Family, Continued OmniBAS™ IDUs, continued

Indoor Unit (IDU)

Description OmniBAS™-8W is the base for the leading CBAN (Converged Backhaul Aggregation Node) supporting flexibly all MW technologies appropriate for HetNets backhauling. It is a Native-IP, highly-modular 2RU indoor unit and is capable of accommodating in the same chassis the following cards: • a combination of eight modem cards • two interface cards • two controller cards

OmniBAS™-8W

Modem cards can be flexibly chosen based on the connection type to the outdoor unit: • radio connection to an ODU using coaxial IF cable • PonE connection to an all-outdoor unit (i.e OmniBAS™ OSDR) system using Ethernet cable Interfaces • 2 x GbE (electrical) & 4 x GbE (SFP), per control card • - / 16 / 32 x E1, per interface card • 2 / 4 x STM-1 (VC-12), per interface card OmniBAS™-4P is an 1RU, half-rack IDU unit used as an expansion PonE unit to enable connectivity and control of up to four all-outdoor units (OmniBAS™ OSDR).

OmniBAS™-4P

4

Interfaces • 4 x GbE (electrical PonE enabled) & 2 x GbE (SFP) • 16 x E1


Safety Precautions PROPER GROUNDING Never power up the indoor equipment not yet connected to a proper grounding system. There is risk of equipment failure and/or electrical shock. Ensure that the indoor grounding system measures a path resistance less than 4 Ω.

INDOOR EQUIPMENT PROPER SWITCHING ON / OFF Never connect or disconnect the power supply cable(s) to or from the indoor equipment when the local dc power supply source is on. There is risk of equipment failure. Ensure the local dc power supply source is off and then connect or disconnect the power supply cable(s) to or from the indoor equipment.

PROTECTION FROM LIGHTNING Never leave the IF cable coming from the Outdoor Unit without adequate lightning protection. There is risk of equipment failure and/or electrical shock. Ensure that the IF cable coming from the Outdoor Unit is properly grounded as described in the Outdoor Radio Equipment Installation Manual (GDC001/81 manual code).

ESD PROTECTION Always use proper antistatic protection (i.e. grounding bracelet, antistatic bags, etc.) when handling the system cards. Parts bearing the ESD sign (see left) have ESD sensitive exposed components.

5

Chapter 2. Installation Tools

2

Installation Tools

Tools List

This chapter describes the tools requirements for the proper equipment installation (1):

Item

(1)

6

Photo

Description

1

Cros screw drivers: • (A): PH-1 • (B): PH-3

2

Blade

3

Wire Stripper

4

Cable Jacket Stripper

5

Crimping tool for 1,5 / 2,5 & 4 mm2 cable contact with the appropriate die

6

Torque wrench 0,8 – 1,13 Nm, 8 mm

7

Hot-air blower

The tools supply is installer responsibility.


3

Installation Material

OmniBAS-2W Package Contents

The following table depicts the IDU contents for installation:

No

Description

1

IDU Factory Test Results Paper.

2

IDU Standard Installation Material.

3

OmniBASTM-IDU.

The package contents is the same for all types of OmniBASTM-2W IDU’s. Keep the packaging of the equipment in good condition for later use (i.e. safe transportation during relocation, return for repair, etc.). In case of disposal of the packaging material, it is recommended to follow the safe disposal procedure according to local law. Continued on next page

7

Chapter 3. Installation Material

OmniBAS-2W, Continued Mounting kit

No

IF Tail

Qty (per indoor unit)

Description

1

Screw, M6 x 12

4

2

Washer, od = 15, id = 6,4

4

3

Caged nut, M6

4

The following set is supplied per modem card.

No

Description


1

IF Tail 1,5m, RG223 SMA-type male, R/A to N-type female connector

1

(A): O-ring

1

(B): Toothed lock washer

1

(C): Nut

1

2

Continued on next page

8


OmniBAS-2W, Continued Power connector

No


Description

1

2-pole power connector

2

2

Heat Shrinkable Tube, 10 cm

1

3

Metallic pins for power connector for cable up to 1.5 mm2

4

4


4

No

Description


Tie-wraps

1

Tie-wraps 45cm, for indoor cables fastening

20

2

The screw and nut included are for connection of OmniBASTM IDU grounding cable to the rack grounding terminal

1

Serial Cable for external alarms

Description External Alarm Cable 2m, Y-Type, DB9(Female), DB15(VGA), open end

Qty (per indoor unit) 1 per idu

9


OmniBAS-4W/8W Package Contents

The following table depicts the IDU contents for installation:

OmniBAS-4W No

OmniBAS-8W Description

1

IDU Factory Test Results Paper.

2

IDU Standard Installation Material.

3

OmniBASTM-IDU.

Keep the packaging of the equipment in good condition for later use (i.e. safe transportation during relocation, return for repair, etc.). In case of disposal of the packaging material, it is recommended to follow the safe disposal procedure according to local law. Continued on next page

10


OmniBAS-4W/8W, Continued Mounting kit

No

IF Tail


Description

1

Screw, M6 x 12

4

2

Washer, od = 15, id = 6,4

4

3

Caged nut, M6

4

The following set is supplied per modem card.

No

Description


1

IF Tail 1,5m, RG223 SMA-type male, R/A to N-type female connector

1

(A): O-ring

1

(B): Toothed lock washer

1

(C): Nut

1

2


11


OmniBAS-4W/8W, Continued Power connector

No


Description

1


2

2


1

3


4

No

Description


Tie-wraps

1

Tie-wraps 45cm, for indoor cables fastening

20

2

The screw and nut included are for connection of OmniBASTM IDU grounding cable to the rack grounding terminal

1


12


OmniBAS-4W/8W, Continued Cables

1 (OPTIONAL)

No

2

Description


1

External Alarm Cable 2m, Y-Type, DB9(Female), DB15(VGA), open end.

1

2

Indoor unit grounding cable, 0.5 m, already terminated at both ends.

1

13


OmniBAS-4P Package Contents

The following pictures shows the IDU contents for installation:

Description OmniBASTM-IDU. IDU Installation Material (1). Continued on next page

(1)

Standard & Optional.

14


OmniBAS-4P, Continued IDU standard installation material

No

Description


1


1

2


1

3

Metallic pins for power connector for cable 2.5 up to 4.0 mm2

4

IDU optional installation material

Order Code: ACC-RM-O4P (1) Description: 19’’ RACK MOUNTING KIT for OmniBAS 4P No

(1)

Description


1

Screw, M6 x 20.

4

2

Finishing Washer for M6.

4

3

Caged nut, M6.

4

4

Lockwasher M3.

6

5

Screw, M3 x 8.

6

6

Mounting brackets (left, right)

2

Includes installation leaflet.

15

Chapter 4. Before Starting the Installation

4

Before Starting the Installation

4.1 Installation Prerequisites Introduction

This section describes the main actions that must be taken in consideration prior to the equipment installation.

Site survey

Site survey should take place before starting the installation, taking into account the following:

• Location of appropriate grounding points. • Location of appropriate power supply distribution points. • Location of cable conduits available for routing the coaxial cables (interconnecting the indoor with the outdoor equipment) • Location of the network port distributors. • Thermal considerations and cooling requirements for the rack-mounted equipment. • Equipment rack occupation details.

Network port distributors

Regarding the network ports (inclusive of STM-1, Ethernet, E1) provided by the indoor equipment, suitable optical (or electrical) network port distributors should be available. The exact location of the network port distributors, as well as the network ports to reserve, should be known prior to installing the indoor equipment. Also, all the reserved ports on the network port distributors should be qualified and tested before realizing the network connections with the indoor equipment.

Indoor premises conditions

The operating conditions (temperature, humidity) at the indoor premises should meet the specifications given by the manufacturer of the indoor equipment.

Indoor grounding system

All racks within the installation premises should be connected to a lowresistance grounding system. The metal body of the rack, into which the subracks are to be mounted, should be connected to this grounding system. The enclosure of each subrack must be electrically connected to the rack’s metal body (via a short grounding cable) to provide protection against harmful discharge conditions. Continued on next page

16


Installation Prerequisites, Continued Cable conduits

Appropriate cable conduits should exist for the routing of installed cables, inclusive of the coaxial IF cable(s) connecting the indoor equipment with the outdoor transceiver boxes on the building’s roof.

Power supply requirements

The OmniBASTM - 2W/4W/4P subracks require connection to a DC distribution board accommodating either one or two Magnetic Circuit Breakers (MCB, single-pole, 7 A, 80 V dc, B-curve for Telecom Applications). The OmniBASTM – 8W subracks require connection to a DC distribution board accommodating either one or two Magnetic Circuit Breakers (MCB, single-pole, 25 A, 80 V dc, B-curve for Telecom Applications).

Maximum power supply length

Regarding the power supply cables to be used, calculation of the maximum length depends on the available power supply source and the OmniBASTMIDU disconnect voltage, which is -40.5 V. By assuming the following: • Use of -48 (1) V nominal voltage. • Availability of 2.5 mm2 or 4 mm2 multi-stranded copper cables. • Maximum power consumption of OmniBAS systems (taking the connected radio systems into account), which is: • 250 W (OmniBAS 4W) • 550 W (OmniBAS 8W), then, the maximum power cable lengths (2) are as follows: • OmniBASTM- 4W: 84 m (2.5 mm2), 138 m (4 mm2). • OmniBASTM- 8W: 38 m (2.5 mm2), 63 m (4 mm2). Continued on next page

(1)

If the nominal value of -48 V changes then the cable length differentiates respectively.

(2)

The power supply length is calculated based on the IDU operational temperature 25 °C

17


Installation Prerequisites, Continued Lightning protection

The network port distributors (optical distributors excluded) and the power supply distributors should be equipped with the appropriate gas arresters, to provide protection against lightning conditions. Such conditions may induce voltage peaks on the cables, and thus disturb the operation of the indoor equipment. For this purpose, all electrical distributors should be connected to the local grounding system to allow the installed gas arresters to operate.

Safety

The indoor equipment premises should be of restricted access. Only trained, authorized personnel should have access to the installed equipment. Appropriate labeling should exist at points with high risk of contact with hazardous voltage. A list with emergency phone numbers (e.g. medical assistance numbers) should be hung at easy-to-view positions. Also, recommended are for safety purposes, a fire detection system and fire extinguishers (installed at easy-to-access points) inside the installation premises. Continued on next page

18


Installation Prerequisites, Continued Rack space requirements

The indoor equipment will be installed in an ETSI equipment rack.

IDU

Rack Space

2W

1RU

4W

1RU

8W

2RU

Air-flow Direction

No extra space is required for cooling. Furthermore, sufficient free space should be left around the rack position to allow for easy access, handling, maintenance and inspection of the installed equipment.

19


4.2 Cabling Overview The following list shows all the cabling types that can be installed on the IDU’s: Cabling Type Modem

RJ-45

SFP E1

20

Concerns Interconnection between: • IF modem card with ODU • WOE modem card with all-outdoor system Interconnection between: • Electrical Ethernet ports with switches for traffic • Electrical Ethernet ports with switches for outband management Interconnection between: SFP ports with switches or all-outdoor systems for traffic Interconnection between: E1 ports (120 Ω) with switches for traffic

Power

Interconnection between: DC power input with power supply

Others

• Auxiliary • Synchronization • PonE for traffic and Power


Modem Cabling IF modem

Cables are denoted as shown below and the type is: IF Tail.


21


Modem Cabling, Continued WOE (Wireline Modem Optical/ Electrical)

No

Connection Details

Cable Description

1

Electrical GbE interface (GbE/ DC OUT) that superimposes the operating DC voltage (Power on Ethernet – PonE) for running a single cable for traffic, inband management and power.

2

• Optical (GbE) SFP interface for traffic and inband • Fiber Optical cable management using the hotpluggable • Electrical Fast Ethernet interface (DC OUT/ MNG) that transceiver SFP provides the DC power (PonE) and outband (small form-factor management to the all-outdoor radio system (OSDR). pluggable). This connection is essential when the optical (SFP) interface is used. • S-FTP cable(1).

3

Electrical Fast Ethernet interface (MNG) for the connection of an external client for outband management when using the DC OUT/ MNG interface.

S-FTP cable (1).

• Cat-5 or higher Fast Ethernet straight cable. • S-FTP cable(1).

GbE and GbE/ DC OUT interfaces cannot operate simultaneously.

(1)

How to prepare an S-FTP cable please refer to Reference Manuals item 2 on page 1

22


RJ-45 Cabling (Ethernet Payload) Traffic

Cables are denoted as shown below and the type is: CAT-5 or higher Gigabit Ethernet straight cable.

OmniBAS-2W: See Dual SFPs installed on page 25.

23


RJ-45 Cabling (Outband Management) Outband management

Cables are denoted as shown below and the type is: CAT-5 or higher Gigabit Ethernet straight cable.

OmniBAS-2W: You can use either NMS-1 or NMS-2 port.

24


SFP Cabling (Ethernet Payload) Traffic

Cables are denoted as shown below and the type is: • either Fiber Optical cable using the hot-pluggable transceiver SFP (small form-factor pluggable) • or CAT-5 or higher Gigabit Ethernet straight cable using the hotpluggable transceiver SFP (small form-factor pluggable)

Dual SFPs installed

When Dual Media SFPs are installed (GbE1 and GbE2) then only two out of four electrical GbE interfaces (1, 2, 3 and 4) can be used.

25


SFP Cabling (STM-1 Payload) Traffic

26

Cables are denoted as shown below and the type is: Fiber Optical cable using the hot-pluggable transceiver SFP (small form-factor pluggable)


E1 Cabling (Balanced 120 Ω) Traffic

Cables are denoted as shown below and the type is: 1 x 16 E1 cable (Balanced 120 Ω).

27


Power Supply Cabling Power supply cables are denoted as shown below and the type is: Black Color, stranded, PVC, 300 V, 2 x 1,5 or 2,5 or 4 mm2

OmniBAS-2W/4W: Both POWER inputs are operational. The second POWER (PWR 2) supply connection is optional. OmniBAS-8W: Only the right POWER input (PWR 1) of the controller card is operational.

28


Other Cabling Auxiliary (AUX)

Cables are denoted as shown below and the type is relative to each IDU:


29


Other Cabling, Continued Synchronization

Synchronization cables are denoted as shown below and the type is: External Synchronization Cable (IN/OUT).


30


Other Cabling, Continued Traffic and power (PonE)

The cables are denoted as shown below and the type is: S-FTP.

DO NOT connect cable(s) GbE 1 up to 4 to any network equipment. There is risk of switches / routers failure due to potential power. Use the cable(s) for connection to OSDR.

31

Chapter 5. Mechanical Installation

5

Mechanical Installation

5.1 OmniBAS-2W Chassis Overview Introduction

OmniBAS™-2W is a Native-IP indoor unit (1 RU suitable for mounting in 19″ racks) accommodating up to two modem cards.

(Indicative model IDU-O2-E2-16-G)

For availability of OmniBASTM-2W product (models, cards and common parts), please contact [email protected] or your Account / Project Manager.

Slots

Slot

(1)

Reserved for future use (Fan Tray).

32

Card/Part

M1, M2

Modem card.

C

Control card.

D

Dummy Panel (1).


IDU Installation Prerequisites

Ensure that the installation premises are equipped with a reliable, lowimpedance ground connection system.

Required Tools & Accessories

The following tools will be needed: • Item 1-B (refer to Installation Tools on page 6) The following accessories will be needed: Product

Description

TM

Mounting kit (refer on page 8)

OmniBAS -2W TM

-

TM

-

TM

-

OmniBAS -4W OmniBAS -8W OmniBAS -4P

Procedure

To perform the mechanical installation of the unit, follow the steps below: Step

Action

1

Use the mounting kit to install the chassis into the rack, as shown below. (A) First install the cage nut (item 1) on the desired rear side of the rack. (B) Lift the idu on the corresponding position. (C) Mount the idu using the screw (item 2) on the front side of the rack.

2

To ground OmniBASTM-2W, connect the loose end of the grounding cable to the rack grounding terminal.

End of procedure

33



OmniBAS™-4W v2 (1) is a Native-IP indoor unit (1 RU suitable for mounting in 19″ racks) accommodating up to four modem cards and providing flexible network deployments, through multiple available configurations. OmniBAS-4W uses the same cards as OmniBAS-8W.

(Indicative model IDU-O4-E4-16-G)


Slots

Slot

(1)

Card/Part

M1…M4

Modem card.

C

Control card.

I

Interface card.

F

Fan tray.

v2 is used to differentiate from previous version of OmniBAS-4W IDU’s..

34






Description

OmniBASTM-2W

-

TM

OmniBAS -4W OmniBASTM-8W TM

OmniBAS -4P Procedure

Mounting kit (refer to page 11) -


Action

1

Use the mounting kit to install the chassis into the rack, as shown below. (A) First install the cage nut (item 1) on the desired rear side of the rack. (B) Lift the idu on the corresponding position. (C) Mount the idu using the screw (item 2) on the front side of the rack.


35


IDU Installation, Continued Procedure (continued)

Step

Action

2

3

To ground the idu choose one of the two grounding points on the rear side of the idu which is designated with the respective sign, as shown below. Install the cable as shown below. The other end of the cable must be connected to rack grounding terminal.

End of procedure

36



OmniBAS™-8W is a Native-IP indoor unit (2 RU suitable for mounting in 19″ racks) accommodating up to eight modem cards and providing flexible network deployments, through multiple available configurations.

(Indicative model IDU-O8-E503-32-S4-GP)


Slots

Slot M1…M8 C1, C2 I1, I2 F

Card/Part Modem card. Control, PSU card. Interface card. Fan tray.

37






-

TM

-

OmniBAS -2W OmniBAS -4W TM

OmniBAS -8W TM

OmniBAS -4P

Procedure

Mounting kit (refer to page 11). -


Action

1

Use the mounting kit to install the chassis into the rack, as shown below. (A) First install the cage nut (item 1) on the desired rear side of the rack (B) Lift the idu on the corresponding position (C) Mount the idu using the screw (item 2) on the front side of the rack

2

Follow the steps 2 & 3 as described in procedure of OmniBAS-4W IDU installation on page 35.

End of procedure.

38

Description

TM


5.4 OmniBAS-4P Chassis Overview Introduction

OmniBAS™-4P is an 1RU, half-rack IDU used as an expansion PonE unit to enable connectivity and control of up to four all-outdoor units (OmniBAS™ OSDR).

(IDU-O4P)

Slots / Interfaces

Slot P Gb1…Gb4 IN, OUT Gb5, Gb6

Description DC Power input. 4 x GbE electrical (RJ-45) ports for traffic and PonE power connection. Synchronization Input / Output ports. 2 x GbE (SFP) ports for traffic.

NMS

Fast Ethernet (RJ-45) port for outband management.

AUX

Serial - console (RJ-45) port (AUX).

E1

16 x E1 interfaces for TDM traffic over Ethernet encapsulated in PW-TDM.

39





The following tools will be needed for rack installation type: • Item 1-A & B (refer to Installation Tools on page 6) The following accessories will be needed: Product

Description

OmniBASTM-2W

-

TM

-

TM

-

TM

IDU optional installation material (refer to page 15)

OmniBAS -4W OmniBAS -8W OmniBAS -4P

Installation

There are two installation types as given below: • •

Desktop - The OmniBASTM-4P is installed as desktop mounting without using materials. Rack - The OmniBASTM-4P is installed in a 19-inch rack (as shown below) using the IDU optional installation material:

For Rack installation please refers to the installation leaflet that is included on the packing list. Continued on next page

40


IDU Installation, Continued Grounding

To ground OmniBASTM-4P connects the loose end of the grounding cable to the rack grounding terminal.

41

Chapter 6. Cabling Installation

6

Cabling Installation

Overview

This chapter describes how to install the following type of cables for all OmniBASTM Products Family. Mainly the cables categorized as follows: • • • • •

42

Power Supply Cables IF Tails E1 Terminations I/O Cable Ethernet Cable


6.1 Power Supply Cables Introduction

The following table provides all the available power cables with the following characteristics:

The cable length is defined based on customer request: Order Code

Description

Product

Black Color, stranded, PVC, 300 V, 2 x 1,5 mm2

• 2W

ACC-KO-PW-VV-25

Black Color, stranded, PVC, 300 V, 2 x 2,5 mm2

• 2W • 4W • 8W • 4P

ACC-KO-PW-VV-40

Black Color, stranded, PVC, 300 V, 2 x 4 mm2

• 4W • 8W

ACC-KO-PW-VV-15

For OmniBASTM-2W/4P it is recommended to use 2 x 2,5 mm2, stranded, PVC, black, 300 V power cable. For OmniBASTM-4W/8W it is recommended to use 2 x 4 mm2, stranded, PVC, black, 300 V power cable.

43


Preparation Introduction

The power cable preparation is common for all OmniBASTM – Products Family.


The following tools will be needed: • Items 2, 3, 4, 5 & 7 (refer to Installation Tools on page 6) The following accessories will be needed: Product OmniBASTM-2W

OmniBASTM4W/8W

OmniBASTM-4P

Description • Power connector (refer on page 9) • Power Supply Cable ACC-KO-PW-VV-25 (refer on page 43) • Power connector (refer on page 12) • Power Supply Cable (1) ACC-KO-PW-VV-40 (refer on page 43) • Power connector (refer on page 15) • Power Supply Cable ACC-KO-PW-VV-25 (refer on page 43) Continued on next page

(1)

Recommended.

44


Preparation, Continued Procedure

For power supply cable preparation and termination to power connector, proceed as follows: Step

Action

1

Strip the wires of the cable as shown below:

2

Cut 50 mm of heat shrink tube and pass it through:

3

Place the stranded wire into the connector contact. If you have stripped the stranded wire properly, the jacket should stop at point (1) and the stranded wire at point (2):


45


Preparation, Continued Procedure (continued)

Step 4

Action Take care to place the appropriate die (1,5 /2,5 / 4 mm2 connector contact) in the crimping tool to avoid damage of the connector contact.

Crimp with the crimping tool. Different views of crimping are shown below:


46


Preparation, Continued Procedure (continued)

Step

Action

5

Repeat steps 3 and 4 for the other stranded wire. When you finish, the cable should resemble to the photo below:

6

Insert the stranded wires into the connector (blue to pin 1, brown to pin 2). You must hear the clicking sound.

7

Heat the heat shrinkable tube with a hot-air blower. When you finish, the cable should resemble to the photo below:

End of procedure

47


Installation OmniBASTM-2W prerequisites

The following are recommended: • The power at the input of OmniBASTM-2W must be in the range –40.5 V dc to –60 V dc. • The positive pole of the power supply source at OmniBASTM-2W station must be grounded.

Power connection overview

Safety requirements require a single pole circuit-breaker to be employed between the local dc power supply source and each power supply of OmniBASTM-2W. The circuit-breaker must disconnect the –V pole of the power supply. Before plugging or unplugging any power cable into OmniBASTM-2W, you must set the circuit breaker(s) to OFF!

No

Description

1

Power Cable

2

Single pole Circuit Breaker (MCB), 7 A, 80 V dc, B-curve for Telecom Applications

3

Local DC Power Distributor

Both POWER inputs are operational. The second POWER (PWR 2) supply connection is optional. Continued on next page

48


Installation, Continued Procedure

To connect the power supply, proceed as follows: Step

Action

1

Switch-off the circuit breaker connected between the OmniBASTM2W and the local dc power supply source.

2

Plug the power supply cable(s) into the power supply receptacle(s) on the front panel of the OmniBASTM-2W without applying excessive force.

Applying pressure while the connector is inserted incorrectly it might cause damage.

If you want to disconnect the power supply cable, push downwards the metallic secure lock on the upper part of the connector (1) and pull outwards to disconnect (2).

End of procedure Continued on next page

49


Installation, Continued OmniBASTM-4W prerequisites

The following are recommended: • The power at the input of OmniBASTM-4W must be in the range –40.5 V dc to –60 V dc. • The positive pole of the power supply source at OmniBASTM-4W station must be grounded.



No

Description

1

Power Cable

2


3


Both POWER inputs are operational. The second POWER (PWR 2) supply connection is optional. Continued on next page

50




Action

1

Switch-off the circuit breaker connected between the OmniBASTM4W and the local dc power supply source.

2





51


Installation, Continued OmniBASTM-8W prerequisites

The following are recommended: • The power at the input of OmniBASTM-8W must be in the range –40.5 V dc to –60 V dc. • The positive pole of the power supply source at OmniBASTM-8W station must be grounded. Connections to the 2nd control card (when installed) are the same to the 1st CTRL card. This applies to power & traffic connection cables. Continued on next page

52


Installation, Continued Power connection overview


No

Description

1

Power Cable

2


3


Only the right POWER input (PWR 1) of the controller card is operational. Continued on next page

53




Action

1

Switch-off the circuit breaker(s) connected between the OmniBASTM-8W and the local dc power supply source.

2





54


Installation, Continued OmniBASTM-4P Prerequisites

The following are recommended: • The power at the input of OmniBASTM-4P must be in the range –40.5 V dc to –60 V dc. • The positive pole of the power supply source at OmniBASTM-4P station must be grounded.


Safety requirements require a single pole circuit-breaker to be employed between the local dc power supply source and each power supply of OmniBASTM-4P. The circuit-breaker must disconnect the –V pole of the power supply. Before plugging or unplugging any power cable into OmniBASTM-4P, you must set the circuit breaker(s) to OFF!

No

Procedure

Description

1

Power Cable

2


3


How to connect the power supply cable refer to Procedure on page 54.

55


6.2 IF Tails IF Tail purpose

You should connect the IF cable coming from the Outdoor Unit to the IF tail to protect the ODU receptacle on the front panel of OmniBASTM indoor units against mechanical damage, which might occur in case of direct connection of the heavy IF cable. Use the requirement tool to tighten the SMA connector.


The following tools will be needed: • Item 6 (refer to Installation Tools on page 6) The following accessories will be needed: Product TM

Description

OmniBAS -2W

• IF Tail (refer on page 8)

OmniBASTM-4W

• IF Tail (refer on page 11)

OmniBASTM-8W

• IF Tail (refer on page 11) Continued on next page

56


IF Tails, Continued Procedure

To connect the IF tail(s), follow the steps below: Step 1

2

Action Never connect or disconnect an IF tail when OmniBASTM-ODU is ON and Operating! There is risk of equipment failure.

Fix the both ends of the IF tail , as shown below: OmniBAS-2W:

OmniBAS-4W/8W:

3

Tight the N-type female connector onto the IF cable coming from the Outdoor Unit.

3

Use the tie-wraps for IF tail cable fastening.

4

Repeat for the remaining IF tails that may exist. The above procedure is applicable for all OmniBASTM-IF modems types. For WOE modems please refer to WOE (Wireline Modem Optical/ Electrical on page 22. Continued on next page

57


IF Tails, Continued Connection using O-ring

Optionally you can fix the N-type connector of the IF tail onto a metallic surface through the nut and washer provided inside the IF tail packaging. If you have such a metallic surface, follow the steps below: Step

Action

1

Open a mounting hole on the metallic surface as in the figure below (dimensions in mm).

2

Put the Ο-ring onto the N-type connector of the IF tail and pass the N-type connector through the metallic surface you have.

3

Put the toothed lock washer and nut onto the N-type connector as protruding from the metallic surface.

5

1 4

4

Item

4

2

2

1

Description

1

O-ring

2

Toothed lock washer

3

Nut

4

N-type connector

5

Metallic surface

Hand tight the IF cable coming from the Outdoor Unit into the Ntype connector protruding from the metallic surface.

End of procedure

58

3

3


6.3 E1 Terminations Overview

This section provides all the available installations of the E1 cables & accessories for OmniBASTM Products Family. Mainly the type of the E1 terminations are categorized as follows: • Open End Cables (Balanced 120 Ω) • BNC Terminations (Unbalanced 75 Ω) • RJ-45 Terminations (Balanced 120 Ω)

Open End Cables (Balanced 120 Ω) Overview

This paragraph describes the E1 Open End Cables (Balanced 120 Ω) installation for the following models: • OmniBASTM-2W/4P • OmniBASTM-4W/8W Continued on next page

59


Open End Cables (Balanced 120 Ω), Continued OmniBASTM2W/4P

The cable characteristics are given below: Order Code

Procedure

Product Description

ACC-LT-16-IO-10

16xE1 Cable, Balanced (120 Ω), 68 Pins High Density Connector to Open End, 10 m

ACC-KT-16-3O-03

16xE1 Cable, Balanced (120 Ω), 68 Pins High Density Connector to Open End,3 m

ACC-KT-16-3O-07


ACC-KT-16-3O-10


To connect the cable, follow the steps below: Step

Action

1

Arrange the cable appropriately so that the Interface Card can be easily inserted / extracted.

2

Plug the cable into the receptacle shown in the figure below and then terminate the open ends of the cable onto the Distribution Frame according to the color cable table (see appendix AppendixD: Open End Cables Color Codes)


60


Open End Cables (Balanced 120 Ω), Continued OmniBASTM4W/8W

The cable characteristics are given below: Order Code

Procedure

Product Description

ACC-WT-U1-VO-3

16xE1 Cable, Balanced (120 Ω), 64 Pins Connector to Open End, 3 m

ACC-WT-U1-VO-10

16xE1 Cable, Balanced (120 Ω), 64 Pins Connector to Open End, 10 m


Action

1


2

Plug the cable into the receptacle shown in the figure below and then terminate the open ends of the cable onto the Distribution Frame according to the color cable table (see appendix AppendixD: Open End Cables Color Codes)

End of procedure

61


BNC Terminations (Unbalanced 75 Ω) Overview

This paragraph describes the BNC terminations (Unbalanced 75 Ω) for the following models: • OmniBASTM-2W/4P • OmniBASTM-4W/8W Continued on next page

62


BNC Terminations (Unbalanced 75 Ω), Continued OmniBASTM2W/4P

The cable / panel characteristics are given below: Order Code ACC-C-T-U1-IDC-IDC-00 ACC-LN-16-1N-VV

Procedure

Product Description 16xE1 Cable, Balanced (120 Ω), both Ends 68 Pins High Density Connector, 0.5 m. Conversion Panel with 68 Pins High Density Receptacle and 16 Pairs(Tx-Rx) BNC (75 Ω) receptacles.


Action

1

Arrange the cable appropriately so that the Cables & Interface Card can be easily inserted / extracted.

2

Plug both ends of the cable into the relevant receptacles, as shown in the figure below:


63


BNC Terminations (Unbalanced 75 Ω), Continued OmniBASTM4W/8W

The cable / panel characteristics are given below: Order Code

Procedure

ACC-WT-CP-IV-07

16xE1 Cable, Balanced (120 Ω), 64 Pins Connector to 68 Pins High Density Connector, 0.7 m.

ACC-LN-16-1N-VV

Conversion Panel with 68 Pins High Density Receptacle and 16 Pairs (Tx-Rx) BNC (75 Ω) receptacles.


Action

1


2

Plug both ends of the cable into the relevant receptacles, as shown in the figure below:

End of procedure

64

Product Description


RJ-45 Terminations (Balanced 120 Ω) Overview

This paragraph describes the RJ-45 terminations (Balanced 120 Ω) for the following models: • OmniBASTM-2W/4P Continued on next page

65


RJ-45 Terminations (Balanced 120 Ω), Continued OmniBASTM2W/4P

The cable / panel characteristics are given below: Order Code

Procedure

Product Description

MOD-W-EC

16xE1 Cable, Balanced (120 Ω), 68 Pins High Density Connector to RJ-45 Jacks, 0.8 m.

MOD-O-MB

Mounting Bracket for 16 x RJ-45 E1 Receptacles.


Action

1

Arrange the cable appropriately so that the controller card & cables can be easily inserted / extracted.

2

Plug both ends of the cable into the relevant receptacles, as shown in the figure below. The E1 numbering is indicated through special cable marking.


66


RJ-45 Terminations (Balanced 120 Ω), Continued Use of RJ-45 Mounting Bracket

You can optionally install the RJ-45 mounting bracket for optimum arrangement of E1 tributary cables, as shown below:

Detail

Detail

67


6.4 I/O Cables Required Accessories

The following accessories will be needed:

Product TM

OmniBAS -2W

Serial Cable for external alarms (refer on page 9)

OmniBASTM-4W

Cables (refer on page 13)

TM

OmniBAS -8W

Procedure for OmniBASTM-2W

Description

Cables (refer on page 13)

To connect the external alarm cable, follow the steps below:

Step

Action

1

Arrange the cable appropriately so that the Controller Card can be easily inserted / extracted.

2

Plug the cable into the AUX receptacle shown in the figure below:

3

Terminate the open end of the cable based on the chromatic code given in Appendix-C: Receptacles Pin Out AUX on page 85.


68


I/O Cables, Continued Procedure for OmniBASTM4W/8W

To connect the external alarm cable, follow the steps below:

Step

Action

1

Arrange the cable appropriately so that the Controller Card can be easily inserted / extracted.

2

Plug the cable into the AUX receptacle shown in the figure below: OmniBAS-4W:

OmniBAS-8W:

3

Terminate the open end of the cable based on the chromatic code given in Appendix-C: Receptacles Pin Out AUX on page 91.

End of procedure

69


6.5 Ethernet Cables OmniBAS Products Family

The cable characteristics are given below:

Order Code

Cable Installation

70

Product Description

ACC-IO-PA-JJ-01

Ethernet Straight Cable Prefabricated, CAT5e, Terminated both ends to RJ-45 Jack, 1 m

ACC-IO-PA-JJ-05


ACC-IO-PA-JJ-10


Terminate each end of the cable to the corresponding RJ-45 jack.


7

Cable Characteristics

7.1 GbE Cable Characteristics OmniBAS-2W Electrical GbE cable characteristics Type of cable

CAT 5 or higher, UTP, 4 pairs x AWG26 / AWG24.

Cable termination (module side)

RJ-45 plug.

Cable terminated on

GbE 100/1000 Mbps with 1, 2, 3, 4 receptacles on the module front panel.

Cable maximum length

100 m.

Type of cable

Fiber.


IEEE 802.3z, 1000Base-X (SFP MSA mechanics).

Cable terminated on

GbE 1000 Mbps with 1, 2 receptacles on the module front panel.


Depends on SFP module.

Optical GbE cable characteristics

71

Chapter 7. Cable Characteristics

OmniBAS-4W/8W Electrical GbE cable characteristics Type of cable



RJ-45 plug.

Cable terminated on

GbE 100/1000 Mbps with 5, 6 receptacles on the module front panel.


100 m.

Type of cable

Fiber.



Cable terminated on

GbE 1000 Mbps with 1, 2, 3, 4 receptacles on the module front panel.




72


OmniBAS-4P Electrical GbE cable characteristics

Type of cable

S-FTP


RJ-45 plug.

Cable terminated on

GbE 100/1000 Mbps with 1, 2, 3, 4 receptacles on the module front panel.


100 m.

Type of cable

Fiber.



Cable terminated on

GbE 1000 Mbps with 5, 6 receptacles on the module front panel.




73


7.2 Fast Ethernet Cable Characteristics OmniBAS-2W Fast Ethernet cable characteristics Type of cable



RJ-45 plug.

Cable terminated on

NMS 10/100 Mbps with 1, 2 receptacles on the module front panel.


100 m.

You should connect the Network Management System (SNMP) either to the NMS 10/100 1 or the NMS 10/100 2 receptacle for outband management connection.

OmniBAS-4W/8W Fast Ethernet cable characteristics Type of cable



RJ-45 plug.

Cable terminated on

MNG 10/100 Mbps with 1 receptacle on the module front panel.


100 m.

You should connect the Network Management System (SNMP) to the NMG 10/100 receptacle for outband management connection.

74


OmniBAS-4P Fast Ethernet cable characteristics

Type of cable



RJ-45 plug.

Cable terminated on

NMS 10/100 Mbps with 1 receptacle on the module front panel.


100 m.

75


7.3 STM-1 Cable Characteristics OmniBAS-4W/8W STM-1 cable characteristics

Type of cable

Multimode/single mode fiber optic cable LC type connector


SFP

Cable terminated on

STM-1 1, 2, 3, 4 receptacles on the module front panel


Various lengths of cables are available

Type of cable

Multimode/single mode fiber optic cable LC type connector


SFP

Cable terminated on

STM-1 1, 2 receptacles on the module front panel


Various lengths of cables are available

STM-1 cable characteristics

76


Appendix-A: Modem Card Installation / Removal Prerequisites

The following prerequisites are common for any modem of OmniBASTMProducts Family and must be taken in consideration before starting any insertion or extraction of the modem card. The Modem Card is hot swappable.

It is recommended before proceeding to the card installation, to wear a grounding bracelet and attach it to one of the two appropriate receptacles on the chassis as given below: Product

Grounding Bracelet Receptacles

OmniBASTM-2W OmniBASTM-4W

OmniBASTM-8W

Never connect or disconnect an IF tail when OmniBASTMODU is ON and Operating! There is risk of equipment failure. If modem IF tail is installed please refer to Procedure on page 57 for how to connect or disconnect the tail. Modem insertion or extraction in a live network must be done by authorized persons ONLY.


77

Appendix-A: Modem Card Installation / Removal

Appendix-A: Modem Card Installation / Removal, Continued Procedure for OmniBASTM-2W

In order to insert a modem card to OmniBASTM-2W indoor unit, please follow the procedure below: Step 1

Action Remove the modem dummy plate and keep it for maintenance reasons.

The Modem dummy plate is required in 1+0 configuration for proper thermal management. 2

Slide the modem card into the appropriate pair of guides and push it in until it connects to the backplane connector.

3

Hand-tight the two screws on the front panel of the modem card to secure the card in place.


78


Appendix-A: Modem Card Installation / Removal, Continued Procedure for OmniBASTM4W/8W

In order to insert a modem card to OmniBASTM-4W/8W indoor unit, please follow the procedure below: Step

Action

1

Remove the modem dummy plate and keep it for maintenance reasons.

2

Slide the modem card into the appropriate pair of guides and push it in until it connects to the backplane connector.

3

Hand-tight the two screws on the front panel of the modem card to secure the card in place.

End of procedure

79

Appendix-B: I/O Connections

Appendix-B: I/O Connections Introduction

The I/O signals are provided by the following receptacles: Product OmniBASTM-2W TM

OmniBAS -4W/8W

IN

OUT

Receptacle

4

4

AUX

3

2

AUX 2 Continued on next page

80


Appendix-B: I/O Connections, Continued OmniBASTM-2W Input alarms connection circuit

The dry-contact input alarms are internally pulled up to +3,3 V. When an external switch is closed, the corresponding signal is “low” (alarm condition).

OmniBASTM-2W Output alarms connection circuit

The alarms transmission circuit receives alarms in TTL form from the microprocessor and routes them as external alarms in dry-contact form. When a “high” signal enters the relay’s driver, the relay is activated and current passes through the load of the corresponding alarm output.

* The maximum ratings for the Voltage Source are: Max DC voltage: V=100 VDC and Max DC current: IL=200 mADC (polarity is insignificant) The loads can be indicator lamps, relays’ coils, buzzers, etc. Continued on next page

81

Appendix-B: I/O Connections

Appendix-B: I/O Connections, Continued The dry-contact input alarms are internally pulled up to +3,3V. When an external switch is closed, the corresponding signal is “low” (alarm condition). +3,3V

SYSTEM

(Each resistor: 10K)

EXIN1 EXIN2 GND

The alarms transmission circuit receives alarms in TTL form from the microprocessor and routes them as external alarms in dry-contact form. When a “low” signal enters an optocoupler, current passes through the load of the corresponding EXTOUT (alarm condition). SYSTEM

LOADS

OPTOCOUPLERS

ALARM SIGNALS

EXOUT1 EXOUT2

V*

IL

GND FL

VOLTAGE SOURCE

* The maximum ratings for the Voltage Source are either: DC: V=100VDC / IL=80mADC (polarity is insignificant) The loads can be indicator lamps, relays’ coils, buzzers, etc.

82

FROM MICROPROCESSOR (TTL LEVEL)

OmniBASTM4W/8W Output alarms connection circuit

TO MICROPROCESSOR (TTL LEVEL)

OmniBASTM4W/8W Input alarms connection circuit


Appendix-C: Receptacles Pin Out OmniBAS-2W Electrical GbE

Location

Front Panel of Control Card

Scope

For Ethernet traffic (100 / 1000 Mbit/s) provisioning and connection to the IP / MPLS network

Type

RJ-45 Female

Pin out

Optical GbE

Pin

Signal

Description

1

Transmit and Receive Data A+

Input / Output

2

Transmit and Receive Data A-

Input / Output

3

Transmit and Receive Data B+

Input / Output

4

Transmit and Receive Data C+

Input / Output

5

Transmit and Receive Data C-

Input / Output

6

Transmit and Receive Data B-

Input / Output

7

Transmit and Receive Data D+

Input / Output

8

Transmit and Receive Data D-

Input / Output

Location


Scope


Type

SFP cage Continued on next page

83

Appendix-C: Receptacles Pin Out

OmniBAS-2W, Continued NMS 10/100 1 and 2

Location


Scope

NMS 10/100 1: For connection to the NMS / GUI or for interconnection (serving management transfer) with another OmniBAS-2W NMS 10/100 2: For connection to the NMS / GUI or for interconnection (serving management transfer) with another OmniBAS-2W RJ-45 Female

Type Pin out

1

8

1

8

Pin

Signal

Description

1

TX+

Output+

2

TX-

Output-

3

RX+

Input+

4

N/A

N/A

5

N/A

N/A

6

RX-

Input-

7

N/A

N/A

8

N/A

N/A


84


OmniBAS-2W, Continued AUX

Location


Scope

For Serial Console (RS-232 Interface) and Internal / External Alarms (Dry Contacts) connection

Type

D-Sub HD 15 Pin Female

Pin out

Pin 1 2

Signal ALM_OUT2_NC RS232_TX

Wire Colour

Description Alarm Output 2 Normally Closed

Black

(1)

Transmit Data from OmniBAS

-

(1)

Receive Data from PC

-

Alarm Output 1 Common

Brown

RS232 Ground

-

Alarm Output 2 Normally Open

Red

Alarm Input 3 Negative

Orange

3

RS232_RX

4

ALM_OUT1_CM (1)

5

RS232_GND

6

ALM_OUT2_NO (2)

7

TTL_ALM_IN3_N

8

TTL_ALM_IN4_N


Yellow

9

ALM_OUT1_NC

Alarm Output 1 Normally Closed

Green

10

ALM_OUT1_NO


Blue

11

ALM_OUT2_CM


Purple

12

TTL_ALM_IN3_P

Alarm Input 3 Positive

Gray

13

TTL_ALM_IN4_P


White

Alarm Input 1

Pink

Alarm Input 2

Light Green

14

TTL_ALM_IN1

15

TTL_ALM_IN2

(3)


(1)

These signals concern a Serial Console connection and are terminated onto the DB9 connector of the cable. (2) Negative return terminal of alarm input pair. (3) Single inputs with respect to ground.

85


OmniBAS-2W, Continued SYNC

Location


Scope

Clock Synchronization Interface (G.703 Clause 13)

Type

1.0 / 2.3 (Micro Siemens)

Pin out

Modem Connector

Pin

Signal

Description

1

Sync In / Out

Synchronization Input / Output (configurable)

Location

Front Panel of Modem Card

Scope

For connection to the Outdoor Unit The receptacle carries the following signals using frequency-division multiplexing: • -48 V dc power to the Outdoor Unit • Bidirectional Service Channel (S.C.) data, enabling communication between Indoor and Outdoor Units. The Service Channel carries an Rx signal centred at 10,7 MHz and a Tx signal centred at 6 MHz, On/Off Keying modulated. • The 140 MHz Rx IF signal • The 350 MHz Tx IF signal

Type

SMA Female

Pin out Pin

Signal

Description

Centre

-48 V DC / S.C. / RX IF / TX IF

Input / Output

Shield

Shield / Chassis GND

N/A Continued on next page

86


OmniBAS-2W, Continued E1/T1 1-16

Location

Front Panel of Interface Card

Scope

For provisioning of up to 16xE1 Tributaries (120 Ω balanced)

Type

Mini D Ribbon (MDR) 68-pin Female

Pin out

E1 tributaries Tx1+ Tx1Rx1+ Rx1Tx2+ Tx2Rx2+ Rx2Tx3+ Tx3Rx3+ Rx3Tx4+ Tx4Rx4+ Rx4Tx5+ Tx5Rx5+ Rx5Tx6+ Tx6Rx6+ Rx6Tx7+ Tx7Rx7+ Rx7Tx8+ Tx8Rx8+ Rx8-

E1 1-16 Recept. 68 67 34 33 66 65 32 31 64 63 30 29 62 61 28 27 60 59 26 25 58 57 24 23 56 55 22 21 54 53 20 19


E1 1-16 Recept. 50 49 16 15 48 47 14 13 46 45 12 11 44 43 10 9 42 41 8 7 40 39 6 5 38 37 4 3 36 35 2 1


87


Power

Location


Scope

For connection of –48 V dc power supply voltage

Type

Two poles Male power connector

Pin out

88

Pin

Signal

(+)

Power Supply Return (GND)

(-)

-48 V dc, nominal (40 V dc to 60 V dc)


OmniBAS-4W/8W Electrical GbE 100/1000 5 and 6

Location


Scope


Type

RJ-45 Female

Pin out

Optical GbE 1000 1, 2, 3, 4

Pin

Signal

Description

1


Input / Output

2


Input / Output

3


Input / Output

4


Input / Output

5


Input / Output

6


Input / Output

7


Input / Output

8


Input / Output

Location


Scope


Type

SFP MSA cage Continued on next page

89


OmniBAS-4W/8W, Continued NMG 10/100

Location


Scope

NMG 10/100: For connection to the NMS / GUI or for interconnection (serving management transfer) with another OmniBAS-IDU

Type

RJ-45 Female

Pin out

1

8

Pin

Signal

Description

1

TX+

Output+

2

TX-

Output-

3

RX+

Input+

4

N/A

N/A

5

N/A

N/A

6

RX-

Input-

7

N/A

N/A

8

N/A


90


OmniBAS-4W/8W, Continued AUX

Location

Front Panel of Control Card`

Scope

For connection of Alarms Inputs / Outputs (Contacts)

Type

Micro-D Female 15C Sockets Connector with UNC2-56 Thumbscrews.

Pin out

Pin

Signal

Description

Wire Color

1

RS232_TX

Transmit Data from OmniBAS

2

RS232_RX

Receive Data from PC

3

RS232_GND

RS232 Ground

4

ALM_OUT2_CM


5

ALM_OUT1_NC


RED

6

ALM_OUT1_NO


ORANGE

7

TTL_ALM_IN3_P


8

TTL_ALM_IN1

Alarm Input 1

GRG

Grounding

ALM_OUT2_NO


BLUE PURPLE

BLACK BROWN

YELLOW GREEN

9 10 11 12

ALM_OUT2_NC


13

ALM_OUT1_CM


14

TTL_ALM_IN3_N


15

TTL_ALM_IN2

Alarm Input 2

GRAY WHITE PINK


91


OmniBAS-4W/8W, Continued Power

Location


Scope

For connection of –48 V dc power supply voltage

Type

Two poles Male power connector

Pin out

SYNC

Pin

Signal

(+)


(-)


Location


Scope

Clock Synchronization Interface (G.703 Clause 13)

Type


Pin out

PPS

Pin

Signal

Description

1

Sync In / Out

Synchronization Input / Output

Location


Scope

External PPS (Pulse Per Second) IN/OUT for phase synch.

Type


Pin out

Pin

Signal

Description

1

PPS In / Out

Pulse Per Second Input / Output Continued on next page

92


OmniBAS-4W/8W, Continued STM-1 (VC-12)

Modem Connector

Location


Scope

For provision of STM-1 VC-12 interfaces and connection to the legacy SDH Network

Type

SFP cage

Location

Front Panel of Modem Card

Scope

For connection to the Outdoor Unit The receptacle carries the following signals using frequency-division multiplexing: • -48 V dc power to the Outdoor Unit • Bidirectional Service Channel (S.C.) data, enabling communication between Indoor and Outdoor Units. The Service Channel carries an Rx signal centred at 10,7 MHz and a Tx signal centred at 6 MHz, On/Off Keying modulated. • The 140MHz Rx IF signal • The 350 MHz Tx IF signal

Type

SMA Female

Pin out Pin

Signal

Description

Centre

-48 V DC / S.C. / RX IF / TX IF

Input / Output

Shield

Shield / Chassis GND


93


OmniBAS-4W/8W, Continued E1 1-16 & 17-32

Location


Scope

For provisioning of up to 16 x E1 Tributaries (120 Ω balanced)

Type

Delander Type, Double Row Dual-edge, 64P IN, Straight Plug

Pin out

94


OmniBAS-4P Electrical GbE

Location

Front Panel.

Scope

For Ethernet traffic (100 / 1000 Mbit/s) provisioning and connection to the IP / MPLS network For PonE connections. RJ-45 Female.

Type Pin out

Optical GbE

Pin

Signal

Description

1


Input / Output

2


Input / Output

3


Input / Output

4


Input / Output

5


Input / Output

6


Input / Output

7


Input / Output

8


Input / Output

Location

Front Panel.

Scope

For Ethernet traffic (1000 Mbit/s) provisioning and connection to the IP / MPLS network

Type

SFP cage. Continued on next page

95


OmniBAS-4P, Continued E1/T1 1-16

Location

Front Panel.

Scope

For provisioning of up to 16xE1 Tributaries (120 Ω balanced).

Type

Mini D Ribbon (MDR) 68-pin Female

Pin out


E1 1-16 Recept. 68 67 34 33 66 65 32 31 64 63 30 29 62 61 28 27 60 59 26 25 58 57 24 23 56 55 22 21 54 53 20 19

34

E1#2 E1#4 E1#6 E1#8

E1#1 E1#3 E1#5 E1#7

68


E1 1-16 Recept. 50 49 16 15 48 47 14 13 46 45 12 11 44 43 10 9 42 41 8 7 40 39 6 5 38 37 4 3 36 35 2 1

1 E1#10 E1#12 E1#14 E1#16

E1#9 E1#11 E1#13 E1#15

35 Continued on next page

96


OmniBAS-4P, Continued Power

Location

Front Panel.

Scope

For connection of –48 V dc power supply voltage.

Type

Two poles Male power connector.

Pin out

NMS

Pin

Signal

(+)


(-)


Location

Front Panel.

Scope

NMS 10/100 Mbps for outband management.

Type

RJ-45 Female

Pin out

1

8

Pin

Signal

Description

1

TX+

Output+

2

TX-

Output-

3

RX+

Input+

4

N/A

N/A

5

N/A

N/A

6

RX-

Input-

7

N/A

N/A

8

N/A


97


OmniBAS-4P, Continued SYNC IN/OUT

Location

Front Panel.

Scope

Clock Synchronization Interface (G.703 Clause 13).

Type


Pin out

AUX

Pin

Signal

Description

1

Sync Out

Synchronization Output

2

Sync In

Synchronization Input

Location

Front Panel.

Scope

For internal / external alarms

Type

RJ-45 Female

Pin out

98

1

8

Pin

Signal

Description

1

N/A

N/A

2

N/A

N/A

3

TXD

Device Transmit

4

GND

GND

5

GND

GND

6

RXD

Device Receive

7

N/A

N/A

8

N/A

N/A


Appendix-D: Open End Cables Color Codes Color code of the cable Group Color

See below the color code table, for open end E1 cable (Balanced 120Ω) with order code ACC-LT-16-IO-10 Wire Color

Signal

Cable Conn. Pin

Cable Conn. Pin

Signal

Wire Color

White

RXN16

1

35

TXN16

White

Blue

RXP16

2

36

TXP16

Blue

White

RXN15

3

37

TXN15

White

Orange

RXP15

4

38

TXP15

Orange

White

RXN14

5

39

TXN14

White

Green

RXP14

6

40

TXP14

Green

White

RXN13

7

41

TXN13

White

Brown

RXP13

8

42

TXP13

Brown

Red

RXN12

9

43

TXN12

Red

Blue

RXP12

10

44

TXP12

Blue

Red

RXN11

11

45

TXN11

Red

Orange

RXP11

12

46

TXP11

Orange

Red

RXN10

13

47

TXN10

Red

Green

RXP10

14

48

TXP10

Green

Red

RXN9

15

49

TXN9

Red

Brown

RXP9

16

50

TXP9

Brown

17

51

18

52

Blue

Group Color

Orange

Black

RXN8

19

53

TXN8

Black

Blue

RXP8

20

54

TXP8

Blue

Black

RXN7

21

55

TXN7

Black

Orange

RXP7

22

56

TXP7

Orange

Black

RXN6

23

57

TXN6

Black

Green

RXP6

24

58

TXP6

Green

Black

RXN5

25

59

TXN5

Black

Brown

RXP5

26

60

TXP5

Brown

Yellow

RXN4

27

61

TXN4

Yellow

Blue

RXP4

28

62

TXP4

Blue

Yellow

RXN3

29

63

TXN3

Yellow

Orange

RXP3

30

64

TXP3

Orange

Yellow

RXN2

31

65

TXN2

Yellow

Green

RXP2

32

66

TXP2

Green

Yellow

RXN1

33

67

TXN1

Yellow

Brown

RXP1

34

68

TXP1

Brown


99

Appendix-D: Open End Cables Color Codes

Appendix-D: Open End Cables Color Codes, Continued Color code of the cable

See below the color code table, for open end E1 cable (Balanced 120Ω) with order code ACC-KT-16-3O-03 (07) (10)


100


Appendix-D: Open End Cables Color Codes, Continued Color code of the cable

See below the color code table, for open end E1 cable (Balanced 120Ω) with order code ACC-WT-U1-VO-3 (10)


101

Appendix-D: Open End Cables Color Codes

Appendix-D: Open End Cables Color Codes, Continued Color code of the cable, continued

102


(Page intentionally left blank)

103

www.intracom-telecom.com

OmniBAS_ IDU_ Installation and Cabling_ Manual_en_ed 6.0

Recommend Documents