MTN - TI - BTS Installation Handbook - DN607140 TI.04.pdf

TELECOM IMPLEMENTATION

Ultrasite BTS Installation Hand Book (GSM 900 – DCS 1800) Telecom Implementation On this document you can find: - UltraSite BTS Outdoor Installation On this document you can find the following slides: - Generic Location of the BTS Cabinets and Eltek Power Supply - Grounding and Bridge Kit - Location of the Plug In Units - TRX Cabling for 900 and 1800 BTS Cabinets - Entry Cable Standard - DC and AC Cables - Synchronization Between Cabinets (Master and Slave) - Transmission and Cross-Connection Between Cabinets - Transmission Cable

Slide 1 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Generic Location of the Cabinets Case 1 Feeder cables going to the left side

Case 2 Feeder cables going to the right side

ATTENTION: 1800 CABINET MIGHT NOT BE APPLICABLE FOR SOME CONFIGURATIONS (ROAD SITES)

Slide 2 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Fixing the Cabinets Ensure the Eltek Cabinet and BTS 900 has a distance (gap) of 1cm. This gap is needed because the Eltek cabinet has some screws blocking the opening of the 900 cabinet roof.

Slide 3 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Grounding BTS Grounding MUST be installed immediately after fixing the cabinets in the base frame.

Slide 4 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Bridge Kit

ATTENTION: TWO CABINETS MIGHT NOT BE APPLICABLE FOR SOME CONFIGURATIONS (ROAD SITES) Slide 5 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Location of the Plug-In Units (6+6+6 Configuration) Plug-In Units can be installed only after BTS Grounding.

BTS 1800 P W S B

M 2 H A

P W S B

B B 2 F

B B 2 F

B B 2 F

B B 2 F

B B 2 F

B B 2 F

TRX 1 – 1800 – SECTOR 1 TSDB

B O I A

BTS 900

F X C R R I

1800 SYSTEM

WCDA

TRX 2 – 1800 – SECTOR 1 TSDB

P W S B

M 2 L A

B B 2 F

B B 2 F

B B 2 F

B O I A

F X C R R I

900 SYSTEM

TRX 1 – 900 – SECTOR 1 TSGB DVGA TRX 2 – 900 – SECTOR 1 TSGB

DVDB M 2 H A

M 2 H A

TRX 3 – 1800 – SECTOR 1 TSDB TRX 4 – 1800 – SECTOR 1 TSDB

WCDA

TRX 5 – 1800 – SECTOR 2 TSDB

WCDA

TRX 6 – 1800 – SECTOR 2 TSDB

M 2 L A

M 2 L A

TRX 3 – 900 – SECTOR 2 TSGB DVGA TRX 4 – 900 – SECTOR 2 TSGB TRX 5 – 900 – SECTOR 3 TSGB DVGA TRX 6 – 900 – SECTOR 3 TSGB

DVDB M 2 H A

M 2 H A

TRX 7 – 1800 – SECTOR 2 TSDB

TRX 7 – SPACE AVAILABLE

TRX 8 – 1800 – SECTOR 2 TSDB

WCDA

TRX 8 – SPACE AVAILABLE

TRX 9 – 1800 – SECTOR 3 TSDB

WCDA

TRX 9 – SPACE AVAILABLE

TRX 10 – 1800 – SECTOR 3 TSDB

TRX 10 – SPACE AVAILABLE DVDB

M 2 H A

TRX 11 – 1800 – SECTOR 3 TSDB TRX 12 – 1800 – SECTOR 3 TSDB

TRX 11 – SPACE AVAILABLE

WCDA

Slide 6 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TRX 12 – SPACE AVAILABLE

TELECOM IMPLEMENTATION

TRX Cabling for 900 Sectors – Example This picture is applicable only for 6+6+6 Configuration

Slide 7 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Location of the Plug-In Units (2+2 or 2+2+2 Configuration) Plug-In Units can be installed only after BTS Grounding.

Slide 8 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

TRX Cabling for 900 Sectors

Slide 9 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

TRX Cabling for 1800 Sectors

Slide 10 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Entry Cable Standards

Slide 11 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

ATTENTION: 1800 CABINET MIGHT NOT BE APPLICABLE FOR SOME CONFIGURATIONS (ROAD SITES)

TELECOM IMPLEMENTATION

Entry Cable Kit – How to Use 1 – When installing
’’ Feeder cable, layer 1 must be cut off 2 – When installing MW Cable (RG223) DO NOT cut any layer 3 – When installing metal pipe, layer 1 or 1 and 2 can be cut 4 – Never leave a hole if there is no cable or pipe

1

2

3

Slide 12 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

WRONG

TELECOM IMPLEMENTATION

DC Cable

Cover must be installed Slide 13 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

AC Cable for Heater

Slide 14 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Synchronization Cable – UUHA Not applicable when only one cabinet is in use OUTPUT INPUT

BTS 1800 – SLAVE

Slide 15 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

BTS 900 - MASTER

TELECOM IMPLEMENTATION

Synchronization Cable – UUHA During the commissioning, in the “Hardware Configuration”, for Cabinet Properties, select “Use autodetected Clock Synchronization between BTS Cabinets”. Not applicable when only one cabinet is in use

Slide 16 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Transmission and Cross-Connection Between Cabinets Not applicable when only one cabinet is in use

BTS 1800 – SLAVE

Slide 17 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

BTS 900 - MASTER

TELECOM IMPLEMENTATION

Transmission Cable 1 – Organize MW Cable inside of the BTS 2 – 1 or 2 loops are allowed and recommended inside of the BTS 3 – Labels must be fixed on the cables (Far End Site Code) 4 – Dummy plates must be installed when TX cards are not.

WRONG

Slide 18 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

Commissioning Cable

BTS End – D9 Male

PC End – D9 Female

Pin No. 2, LMP In

Pin No. 3, Transmitted Data

Pin No. 3, LMP Out

Pin No. 2, Received Data

Pin No., Ground

Pin No. 5, Ground

Slide 19 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

TELECOM IMPLEMENTATION

EDGE ACTIVATION For EDGE Activation, the only thing to be done is to set the ABIS ALLOCATION PROPERLY Abis allocation for 1 3 0 1 1 2 1 3 2 4 2 5 3 6 3 7 4 8 4 9 5 10 5 11 6 12 6 13 14 15 16 17 18 19 20 21 22 23 EDAP 2, 4 24 EDAP 2, 4 25 1 26 3 27 28 29 30 31

the 900 BTS (2+2 Road Sites) 5 7 1 1 2 2 3 3 4 4 5 5 6 6

1 3

TCHs

1 1 2 2 3 3 4 4 5 5 6 6

2 4

1 1 2 2 3 3 4 4 5 5 6 6

2 4

Abis allocation for the 900 BTS (2+2+2) 1 3 5 7 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

1 1 2 2 3 3 4 4 5 5 6 6

EDAP 2, EDAP 2, EDAP 2, EDAP 2, 1 3 5 7 9 11

TRXSIG

Slide 20 of 20 – 25.Feb.2007 – by Stevan Picolli – DN607140 TI.04

4, 4, 4, 4,

1 1 2 2 3 3 4 4 5 5 6 6

1 1 2 2 3 3 4 4 5 5 6 6

1 1 2 2 3 3 4 4 5 5 6 6

1 3 5 7 9 11

2 4 6 8 10 12

2 4 6 8 10 12

6 6 6 6

OMUSIG

1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Abis allocation for the 1800 BTS 3 5 7 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 1 3 5 7 9 11

1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 1 3 5 7 9 11

EDAP

1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 2 4 6 8 10 12

1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 2 4 6 8 10 12