9100 Compact BTS EVO Installation

Alcatel-Lucent GSM 9100 Compact BTS Indoor/Outdoor Evolution Installation Manual

BTS Document Installation & Dismantling Manual

3BK 17430 3135 RJZZA Ed.03

BLANK PAGE BREAK

Status

RELEASED

Short title All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel-Lucent.

2 / 84

3BK 17430 3135 RJZZA Ed.03

Contents

Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.1 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.2 Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.3 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.4 Initial State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.5 Final State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.6 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.7 Grouped Task Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.2 Site-Specific Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.1 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.2 Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.3 Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.4 Applicable Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install 9100 Compact BTS Indoor/Outdoor Evolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Before Going On Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2.1 Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2.2 Required Knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 Delivery and Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Rack Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.1 Crane Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.2 Manual Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 Rack Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5.1 C1: Case of Steel Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5.2 C2: Case of Concrete Foundation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5.3 C3: Case of Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5.4 C4: Case of Pole Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 Power Supply and Earth Cables Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.1 Installation of Cables in the Site Cable Way . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.2 Protective Earth Cable Connection (GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.3 Power Cables Connection for AC Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.4 Power Cables Connection for DC Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.5 Fit the Mains In Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 PCM Cables Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.1 Install the PCM Cables in the Cables Way . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.2 Cables Passing at Rack Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.3 Cables Connection at Rack Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7.4 Other Connection Possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 Antenna Jumpers Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8.1 Jumper Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8.2 Connection to the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8.3 Connection to the Feeders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9 Options Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9.1 Alarm Cables Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9.2 Synchronization Cables Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10 Finish Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10.1 Label the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3BK 17430 3135 RJZZA Ed.03

5 7 8 8 10 10 10 10 10 11 12 12 12 13 14 14 17 17 17 19 20 20 20 21 21 23 23 27 28 28 31 35 43 50 51 52 54 56 59 60 60 61 63 67 70 70 71 72 74 74 78 81 81

3 / 84

Contents

2.11

4 / 84

2.10.2 Close the Cable Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 2.10.3 Leave the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 OUTC Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

3BK 17430 3135 RJZZA Ed.03

Preface

Preface Purpose What’s New

This document describes how to install on site an 9100 Compact BTS Indoor/Outdoor Evolution (CBIE/CBOE) of Alcatel-Lucent BSS.

In Edition 03 The following section were updated: Site-Specific Information (Section 1.2.2) Installation Kits (Section 1.4.1.2). Connection of Optical Fiber PCM cable (Section 2.7.4.3) was added.

In Edition 02 Update for indoor applicability.

In Edition 01 First official release of the document.

Audience

This document is intended for: Installers Site administrators Supervisors Project managers Field service technicians Occasional users.

Assumed Knowledge

You must have a basic understanding of the following: Basic knowledge of Alcatel-Lucent BSS equipment Experience of electrical mounting and cabling.

3BK 17430 3135 RJZZA Ed.03

5 / 84

Preface

6 / 84

3BK 17430 3135 RJZZA Ed.03

1 Overview

1 Overview This section provides general information about the principle of the operation and requirements for the procedure.

3BK 17430 3135 RJZZA Ed.03

7 / 84

1 Overview

1.1 Presentation 1.1.1 Hardware Description 1.1.1.1 Rack Configuration The following figure shows the rack configuration for the 9100 Compact BTS Indoor/Outdoor Evolution installation with an AC variant.

AGX TRM

TRM

AGX

SUMA

System Cooling Fan

Cooling System Air Inlet FANU Heater AC Power Supply

+

HEATER RECTIFIER

+

SR1 SR2 DAC

Figure 1: Example of 9100 Compact BTS Indoor/Outdoor Evolution (CBIE/CBOE) AC Variant 2 Sectors with 1 or 2 TRX

8 / 84

3BK 17430 3135 RJZZA Ed.03

1 Overview

The following figure shows the rack configuration for the 9100 Compact BTS Indoor/Out door Evolution installation with a DC variant.

AGX TRM

TRM

AGX

SUMA

System Cooling Fan

Cooling System Air Inlet FANU Heater SR1 SR2 DAC HEATER

DC Distribution Unit

Figure 2: Example of 9100 Compact BTS Indoor/Outdoor Evolution (CBIE/CBOE) DC Variant 2 Sectors with 1 or 2 TRX

3BK 17430 3135 RJZZA Ed.03

9 / 84

1 Overview

1.1.1.2 Weight and Dimensions The following table gives the overall dimensions with roof overlapping.

CBIE/CBOE

Dimensions (mm)

Average weight (kg)

H= 900

35 empty cabinet

W= 370

70 equipped cabinet

D= 500

1.1.2 Cases The following cases apply: C1: Case of steel construction installation C2: Case of concrete foundation hollow base C3: Case of wall installation C4: Case of pole installation.

1.1.3 Options The following additional equipment can be installed: Alarm cables Synchronization cables.

1.1.4 Initial State To begin installation the following materials are delivered and packed on site: Rack Installation Kits Additional Equipment.

1.1.5 Final State After installation: Rack is fixed to the floor Subracks are switched OFF Equipment is ready for commissioning.

1.1.6 Restrictions None.

10 / 84

3BK 17430 3135 RJZZA Ed.03

1 Overview

1.1.7 Grouped Task Sequence Before going on site

Before you start

Delivery and checks

Rack transportation

Rack positioning

Power supply and Earth cables installation

PCM cables installation

Antenna jumpers installation

Options installation

Finish installation

3BK 17430 3135 RJZZA Ed.03

11 / 84

1 Overview

1.2 Preparation 1.2.1 Prerequisites Before to begin installation check that: The site is conform to safety rules of General Wiring Handbook The site is ready to receive the rack, according to the SPP 67 The equipment is delivered on site with associated installation kits. Note: The site feeders are not mandatory installed before starting of operation.

1.2.2 Site-Specific Information These information are necessary to start installation: Address and access to the site (key holder) Grounding plate location Customer power supply cabinet location Fuse breakers location in customer power supply cabinet Antenna feeders connection and information (if needed) Rack precise location Final configuration to be installed Number of alarms to be connected (if the case) Alarm terminal blocks location Type of rack to be installed Type of power supply, AC or DC Type of rack fixation (steel construction or concrete construction) PCM connection type (terminal blocks) Abis transmission type (electrical or optical) In case of electrical, PCM cable impedance (120-ohm or 75-ohm) Synchronization configuration (if the case) Optional equipment to be installed.

12 / 84

3BK 17430 3135 RJZZA Ed.03

1 Overview

1.3 Scheduling In order to avoid safety problem on site, the equipment must be installed by a team of 2 installers minimum. The following table gives the duration for the basic tasks. Task

Duration 1st person in mn

Duration 2nd person in mn

Before Going On Site

20

20

Before You Start

30

30

Delivery and Checks

20

20

Rack Transportation (1)

-

-

Rack Positioning (Section 2.5)

20

20

Power Supply and Earth Cables Installation

20

20

PCM Cables Installation

20

-

Antenna Jumpers Installation

20

20

Finish Installation

10

10

Total without optional tasks

160

140

(1)

: Transportation time to final location depending of the site. Mandatory 2 people for manual transport of disassembled equipment.

The following table gives the duration for the optional tasks and additional equipment installation.

3BK 17430 3135 RJZZA Ed.03

Optional Tasks

Duration 1st person in mn

Duration 2nd person in mn

Alarm Cables Installation

15

-

Synchronization Cables Installation

-

30

13 / 84

1 Overview

1.4 Resources 1.4.1 Tools 1.4.1.1 Hardware Tools The following table is used to check, at base, the availability of the required tools. Refer to Tools Catalogue for content checking. Name

Reference

Calibration

Basic set of tools

OUT 001

No

Tightening tool for antenna jumpers 3BK 25050 AA

OUT 003

No

BTS Outdoor specific tools

OUT 007

No

Dynamometric tools

OUT 011

Yes

1.4.1.2 Installation Kits The following table is used to check, on site, the mandatory or optional delivery item kits. The used symbols are: ◊ = mandatory kit # = technical choice kit ∇ = customer option kit. Kits

Mnemo

Reference

Qty

◊

Basic kit CBIE/CBOE

3BK 26431 ABAA

1

#

Wall mounting kit for CBIE/CBOE

3BK 28943 AAAA

1/if neede

#

Floor mounting kit for CBIE/CBOE

3BK 28944 AAAA

1/if neede

#

Pole mounting kit for CBIE/CBOE

3BK 28945 AAAA

1/if neede

#

Transportation bolts

1AD 09973 0001

4/installation team

#

Antenna jumper cable (1m)

BLF1

3BK 05360 BAAA

2/AN

#


BLF2

3BK 05360 CAAA

2/AN

#


BLF3

3BK 05360 DAAA

2/AN

#

120-ohm PCM cable (8 pairs L907/4)

CA120S8

3BK 08965 AAAA

100 m roll

3BK 08965 ABAA

250 m roll

14 / 84

3BK 17430 3135 RJZZA Ed.03

1 Overview

#

◊

Kits

Mnemo

Reference

Qty

75-ohm PCM Cable (8 coax FLEX3/8)

CACOAX8

3BK 25241 AAAA

100 m roll

3BK 25241 ABAA

250 m roll

PC25YG1D 3BK 08957 BAAA

100 m roll

3BK 08957 BBAA

250 m roll

PC05B5

3BK 08938 AAAA

reel

PC16BL1D

3BK 26923 AAAA

100 m roll

3BK 26923 ABAA

250 m roll

3BK 08937 BAAA

100 m roll

3BK 08937 BBAA

250 m roll

GND Yellow/Green cable 1 x 16 mm

2

◊

AC 230 Volts power cable 3 x 1.5 mm2

#

DC -48V power cable 1x 10 mm blue

#

2

DC 0V power cable 1x 10 mm2 black

PC16B1D

∇

Clock Synchronization cable (10 m)

OCC33

3BK 08304 AA

1

∇

Clock Synchronization cable (10 m)

OCC23

3BK 08303 AA

2

∇

Alarm cable 8 pairs (L907/4)

CA120S8

3BK 08965 AAAA

100 m roll

3BK 08965 ABAA

250 m roll

∇

Mechanical part for 24 terminal blocks

MP24

1AD 02843 0001

1

∇

Labels for 24 terminal blocks

LAB

1AD 02853 0001

1

∇

CAD Terminal block

JS10

1AB 06634 0011

4

∇

DDF wall fixation kit

FKW

1AD 02844 0002

1

∇

DDF rack fixation kit

FKR

1AD 02845 0001

1

#

120-ohm jumper for DDF (1 pair L904/1)

CA120S

3BK 08941 AAAA

100 m roll

3BK 08941 ABAA

250 m roll

3BK 08939 AAAA

100 m roll

3BK 08939 ABAA

250 m roll

#

75-ohm jumper for DDF (1 coax FLEX3)

CACOAX1

∇

Terminal block 75 Ohm 8 BNC connectors

1AD 03371 0009

For BNC links

∇

Terminal block 75 Ohm for 1.6-5.6 connectors

1AD 03371 0010

For 1.6-5.6 links

∇

BNCm connector for Flex 3

1AB 00642 0011

2/jumper cable Flex 3

∇

1.6-5.6 connector for Flex 3

1AB 02546 0013

2/jumper cable Flex 3

∇

Specific heat shrinking sheat for Flex 3

1AC 00330 0002

8/CBIE/CBOE

◊

Shims for levelling (1 Set for 10 racks)

3BK 26159 AAAA

1/10 CBIE/CBOE

3BK 17430 3135 RJZZA Ed.03

ST75

15 / 84

1 Overview

Kits

Mnemo

Reference

∇

Cable Optical fiber LC-LC 2SM 15m

849122239

∇


849125380

∇


849122247

∇


849123591

∇


849125398

∇


849123609

∇


849125406

∇


849125414

∇


849125422

∇


849125430

∇

Cable Optical fiber LC-LC 2MM 5m

849125513

∇


849122270

∇


849125521

∇


849122288

∇


849123633

∇


849125539

∇


849123641

∇


849125547

∇


849125554

∇


849125562

∇


849125570

∇

SFP MOD 1000BASE-LX10

1AB 18728 0029

∇

SFP MOD S-16.1

1AB 19467 0019

∇

SFP MOD S-16.1

1AB 19467 0018

∇

SFP MOD 1000BASE-SX

1AB 18728 0063

∇

SFP MOD I-16.1

1AB 18728 0064

∇

SFP MOD S-16.1

1AB 18728 0065

∇

SFP MOD L-16.1

1AB 18728 0066

16 / 84

Qty

3BK 17430 3135 RJZZA Ed.03

1 Overview

1.4.2 Forms You must have the following forms: BSS Site Premises Inspection Form (post handover) 8BL 00704 0016 DRBRA Site Premises Inspection Form (CEL) 8BL 00704 0015 DRBRA

1.4.3 Supplies Installer or subcontractor must supply: One set of sleeves to fit at each end of cables (PCM, Alarm, Power, ...) One set of screws, nuts and washers to connect power cables to Site Power Box and to Earth Plate One set of terminal lugs for power cables.

1.4.4 Applicable Documents You need the following GSM documents to complete this scenario: Applicable Notification List (3DF 00462 0004 AAAGA) Catalogue of Instruction Operation for GSM (3DF 00300 0004 UAZZA) IO 78 - 9100 BTS Radio Configurations for Antenna Supervision (3DF 00300 0078 UAZZA) Tools Catalogue for field activity for GSM (3BK 20458 0001 RJZZA) BSS Methods Handbook (3BK 17430 0002 RJZZA) Installation Manual Generic Completion Check List for GSM (3BK 17200 0002 QZZZA) General Wiring handbook for GSM (3BK 17160 0001 RJZZA) Installation Method of DDF for BSS Equipment (3DF 00435 0033 RJZZA) 9100 BTS Hardware Description (3BK 21242 AAAA TQZZA) Site Premise Inspection Form (8BL 00704 0015 DRBRA) Site Preparation Specifications 9100 Compact BTS Outdoor Evolution (CBOE) 8BL 00704 0084 DRZZA Site Preparation Specifications 9100 Compact BTS Indoor Evolution (CBIE) 8BL 00704 0086 DRZZA

3BK 17430 3135 RJZZA Ed.03

17 / 84

1 Overview

18 / 84

3BK 17430 3135 RJZZA Ed.03

2 Install 9100 Compact BTS Indoor/Outdoor Evolution

2 Install 9100 Compact BTS Indoor/Outdoor Evolution Install 9100 Compact BTS Indoor/Outdoor Evolution section presents all the checks needed before starting the installation, and all detailed tasks to be performed on site.

3BK 17430 3135 RJZZA Ed.03

19 / 84


2.1 Before Going On Site Before going on site, you must check that the following information and supplies are available: The customer has been informed of the: Date and time Site name and address Purpose of the operation. All Prerequisites (Section 1.2.1) are fulfilled Personnel is available and ready for operation (see Scheduling (Section 1.3)) Site-Specific Information (Section 1.2.2) is available and ready for operation All Hardware Tools (Section 1.4.1.1) and Supplies (Section 1.4.3) are available and ready for operation Applicable Documents (Section 1.4.4) are available.

2.2 Before You Start 2.2.1 Checks On arrival at site, before you start, perform the following operations: Check that all Prerequisites (Section 1.2.1) are fulfilled Check applicable notifications and operating instructions (refer to Catalogue of Technical and Logistic Information (ITL-PRO) and Catalogue of Instruction Operation (IO)) Check that all Hardware Tools (Section 1.4.1.1) and Supplies (Section 1.4.3) are available and ready for operation Check that safety precautions have been taken in accordance with the safety instructions described in the General Wiring Handbook Check if any Cases (Section 1.1.2) and Options (Section 1.1.3) apply Complete the header field of the CCL Complete the Site Premises Inspection Form (CEL) Check that the resistance of the antistatic wrist strap is greater than 1M . Connect the anti-static wrist strap to the rack earth.

20 / 84

3BK 17430 3135 RJZZA Ed.03


2.2.2 Required Knowledge You must be familiar with the following: The safety rules and precautions given in the General Wiring Handbook How to document faults and anomalies, as described in the BSS Methods Handbook How to complete the Site Premises Inspection Form (CEL).

2.3 Delivery and Checks For personal and equipment safety, it is important that: During any kind of transportation the door must be closed At door open the door restrainer must be latched.

1

2

Az N°3 320° Baie AR G2_SBTS _O_120 L H

P

1,200,601,20 L P H

AV 430

3

4

1. Unpack the equipment 2. Check the delivery and report any damage to the carrier delivery note

3BK 17430 3135 RJZZA Ed.03

21 / 84


3. Report on CCL: Factory serial number Cabinet serial number

4. Identify the final location of the rack.

22 / 84

3BK 17430 3135 RJZZA Ed.03


2.4 Rack Transportation 2.4.1 Crane Transportation Do not try to lift the cabinet by the roof with crane hooks! The roof must be dismantled in order to lift the cabinet with eyebolts.

2.4.1.1 Dismantle the Roof To prepare the rack: 1. Remove the screws fixing the roof

2. Push the roof to the back

3. Lift the roof and remove it.

3BK 17430 3135 RJZZA Ed.03

23 / 84


2.4.1.2 Crane Transportation Nr

Materials

Reference

Kit

1

Crane transportation bolts

1AD 09973 0001

-

Crane transportation: 1. At the top of the BTS remove the screws (1) (See Figure 3 ) Do not remove the rail (2), it is used during crane transportation.

1

2

Figure 3: Eyebolt Screwing Position 2. Attach the four eyebolts ( inner diameter: 26 mm, thickness :16 mm) to the rack.

Figure 4: Eyebolts

24 / 84

3BK 17430 3135 RJZZA Ed.03


1234567890 1234567890 Figure 5: Crane Transportation For craning the rack: 3. Check that direction of pull [alpha] = minimum 60. The choice of straps (slings), hooks and crane are under responsibility of subcontractor (See Figure 5 ). 4. After reaching the final position disconnect the straps and replace the eyebolts with the screws (1). Do not remove the rail (2) (See Figure 3 ).

2.4.1.3 Close the Roof To close the roof: 1. Put the roof on the top of the BTS.

3BK 17430 3135 RJZZA Ed.03

25 / 84


2. Make sure the guiding pins are in the foreseen holes.

3. Pull the roof to the front.

4. Fix the roof with the screws

H 13

26 / 84

3BK 17430 3135 RJZZA Ed.03


2.4.2 Manual Transportation Cabinet can be lifted and carried manually at top hood along its reinforced side edges.

Cabinet must not be lifted at top hood front and back edge!

Figure 6: Manual Transportation With Straps

Figure 7: Manual Transportation Using the Handles

Figure 8: With Pallet Handling

3BK 17430 3135 RJZZA Ed.03

27 / 84


2.5 Rack Positioning 2.5.1 C1: Case of Steel Construction Nr

Materials

Reference

Kit

1

Screw HM10 x 30

1AD 00050 0048

Floor mounting kit

2

Spring washer M10

1AD 00507 0014

3

Plain washer M10

1AD 0087 0120

4

Nut HM10

1AD 0019 70046

5

Shims for leveling 1-2 mm thick

3BK 26159 AAAA

3BK 28944 AAAA

SHIMS

To fix the rack on steel construction: 1. Drill the steel construction. Holes must be positioned as described in the following figure. Back

481 mm

337 mm

260 mm Front

Figure 9: Drilling Scheme

28 / 84

3BK 17430 3135 RJZZA Ed.03


2. Position the rack on the steel construction.

3BK 17430 3135 RJZZA Ed.03

29 / 84


3. Fix the rack to the steel construction (1, 2, 3, 4 of Figure 10 ). Do not tighten the screws. 1

3

123 123

2 4

Figure 10: Fix the Rack In case of uneven steel construction, check and correct if necessary the antiparallelism between front and back of BTS. It is important that there is no difference in the slope angles that can twist the rack. 4. If necessary insert shims under the CBIE/CBOE support the rack weight. 5. Tighten the screws to fix the rack.

30 / 84

3BK 17430 3135 RJZZA Ed.03


2.5.2 C2: Case of Concrete Foundation Nr

Materials

Reference

Kit

1

Screw HM10 x 30

1AD 00050 0048

Floor mounting kit

2

Nut HM10

1AD 00197 0046

3

Plain washer M10

1AD 00087 0120

4

Spring washer M10

1AD 00507 0014

5

Screw HM10 x 70

1AD 00050 0050

6

CBIE/CBOE profile steel

-

7

Shims for leveling 1-2 mm thick

3BK 26159 AAAA

3BK 28944 AAAA

SHIMS

To fix the rack on concrete floor: 1. Mark on the floor the position of the fixing points as shown in the following figure.

3BK 17430 3135 RJZZA Ed.03

31 / 84


2. Drill the fixing holes (4 holes) (See Figure 11 ) 13 mm

75 mm

Figure 11: Holes Specifications 3. Place the profile steel on the concrete floor. 4. Using the M10 screws fix the steel profile to the ground.

32 / 84

3BK 17430 3135 RJZZA Ed.03


5. Place the rack on the steel profiles and align the fixing holes.

6. Fix the rack to the steel profiles. Do not tighten the screws. 1

3

123 123

2 4

Figure 12: Fix the Rack In case of uneven steel construction, check and correct if necessary the antiparallelism between front and back of BTS. It is important that there is no difference in the slope angles that can twist the cabinet. 7. If necessary insert shims under the CBIE/CBOE to support the rack weight.

3BK 17430 3135 RJZZA Ed.03

33 / 84


8. Tighten the fixing screws.

34 / 84

3BK 17430 3135 RJZZA Ed.03


2.5.3 C3: Case of Wall Installation Nr

Materials

Reference

Kit

1

Screw HM10 x 70

1AD 00050 0050

Wall mounting kit

Expansion plug M10 x 60

1AD 02655 0001

2

Screw HM8 x 20

1AD 00050 0044

3

Plain washer M8

1AD 00087 0126

4

Spring washer M8

1AD 00507 0025

5

Screw M10 x 30

1AD 00050 0048

6

Spring washer M10

1AD 00507 0014

7

Plain washer M10

1AD 00087 0120

8

Nut HM10

1AD 00197 0046

9

90 support

2

10

Straight support

2

11

Wall support

1

12

Cabinet support

1

13

CBIE/CBOE wall drilling template

1

3BK 28943 AAAA

To keep mounting reliability of the rack, the wall to be fixed must be concrete wall.

3BK 17430 3135 RJZZA Ed.03

35 / 84


1. Use the following drawing to mark the position of the fixation holes on the wall.

36 / 84

3BK 17430 3135 RJZZA Ed.03


2. Check that the holes are distributed as described in the following figure.

3. Drill the holes.

3BK 17430 3135 RJZZA Ed.03

37 / 84


4. Identify the component parts of the support. Two pieces of each part are needed to build the support.

5. Build up the support by connecting the parts using the screws, nuts and washers.

38 / 84

3BK 17430 3135 RJZZA Ed.03


6. Install the bracket on the rack left side wall, upper part.

7. Install the other bracket on the wall and fix it using three upper holes.

3BK 17430 3135 RJZZA Ed.03

39 / 84


8. Install the support components on the wall and fix it with the provided screws.

9. Lift the rack and place it on the supports.

10. Remove the roof.

40 / 84

3BK 17430 3135 RJZZA Ed.03


11. Fix the rack to the support, upper part.

12. Fix the rack to the support, lower part.

3BK 17430 3135 RJZZA Ed.03

41 / 84


13. Install the roof.

42 / 84

3BK 17430 3135 RJZZA Ed.03


2.5.4 C4: Case of Pole Installation Nr

Materials

Reference

Kit

1

Screw HM10 x 280

1AD 11792 0001

Pole mounting kit

2

Screw HM8 x 20

1AD 00050 0044

3

Plain washer M8

1AD 00087 0126

4

Spring washer M8

1AD 00507 0025

5

Screw M10 x 30

1AD 00050 0048

6

Spring washer M10

1AD 00507 0014

7

Plain washer M10

1AD 00087 0120

8

Nut HM10

1AD 00197 0046

9

90 support

-

10

Straight support

-

11

Pole support

-

12

Cabinet support

-

13

Fixation bracket

-

3BK 17430 3135 RJZZA Ed.03

3BK 28945 AAAA

43 / 84


To install the CBIE/CBOE rack on a pole: 1. Identify the items used for pole fixation. Six brackets are delivered.

Figure 13: Pole Fixation Bracket 2. Attach the upper mounting plate to one bracket.

3. On the pole mark the position for the fixation brackets. 4. Install the upper mounting plate on the pole. Use a torque of 47 Nm when tightening the support to the pole.

44 / 84

3BK 17430 3135 RJZZA Ed.03


5. Identify the component parts of the support. Two 90 supports and four straight supports are needed to build the support.

6. Build up the support by connecting the parts using the screws, nuts and washers.

Help: Use items 5, 6, 7 and 8 from materials table to connect the support components.

3BK 17430 3135 RJZZA Ed.03

45 / 84


7. Attach two brackets on the support.

46 / 84

3BK 17430 3135 RJZZA Ed.03


8. Install the lower support on the pole. Use a torque of 47 Nm when tightening the support to the pole.

3BK 17430 3135 RJZZA Ed.03

47 / 84


9. Install the bracket on the rack left side wall, upper part.

Help: Use items 2, 3 and 4 from materials table to fix the bracket.

48 / 84

3BK 17430 3135 RJZZA Ed.03


10. Lift the rack on the lower support and attach it to the support with the provided screws, nuts and washers.

11. Fix the rack to the upper mounting plate using the provided screws, nuts and washers.

3BK 17430 3135 RJZZA Ed.03

49 / 84


2.6 Power Supply and Earth Cables Installation This section describes the procedure to : Install cables in the cable tray Connect protective Earth cable Connect 230 volts mains power supply cables for AC variant Connect 48 volts mains power supply cables for DC variant Test the power supply installation. Before making any electrical connections to the rack, ensure that the safety instructions are applied: The electrical power supply is disconnected. Ensure all switches or fuses devoted to the new RACK into the site connection box are powered OFF. Due to high leakage current, the protective EARTH must be connected to the equipment before AC power cable connection. The terminals of the wires, for all the conductive cables (AC, DC and ground) are well tightened, this is very important to avoid damage of the equipment.

50 / 84

3BK 17430 3135 RJZZA Ed.03


2.6.1 Installation of Cables in the Site Cable Way Nr

Material

Reference

Kit

1

Tie wraps

1AD 00414 0006

Basic kit

2

GND cable Y/G in 100m roll

3BK 08957 BAAA

-

GND cable Y/G in 250m roll

3BK 08957 BBAA

AC 230V power cable

3BK 08938 AAAA

3

1

-

2

1m

3

5

4

6

To install the cables in the cable way: 1. Install Yellow / green cable in power compartment of cable tray (lug at BTS side) 2. Install power cables in power compartment of cable tray 3. Attach cables with plastic tie wraps 4. Cut the cables at good length 5. Fit a lug on earth cable at site side 6. Connect the earth cable at the site earth plate.

3BK 17430 3135 RJZZA Ed.03

51 / 84


2.6.2 Protective Earth Cable Connection (GND) Nr

Material

Reference

Kit

1

Lug ring crimp

1AB 03205 0060

Basic kit

2

Tie wraps

1AD 00414 0006

Basic kit

To install the protective earth cable: 1. Crimp a [empty ] 8 terminal lug at RACK side and crimp an adapted lug at site extremity of GND cable

2. Make a label and connect the GND cable to the site earth plate (Example BTS 3 of site)

BTS

52 / 84

3

3BK 17430 3135 RJZZA Ed.03


3. Remove the screws fixing the cable entry cover plate (A) then remove the cover plate.

Cover Plate for Cable Entry

4. Connect earth cable to the grounding stud (8mm).

3BK 17430 3135 RJZZA Ed.03

53 / 84


2.6.3 Power Cables Connection for AC Variant 2.6.3.1 AC 230V Mains Power Supply Connection Nr

Material

Reference

Kit

1

Wire terminal

1AB 05067 0005

Basic kit

2

Tie wraps

1AD 00414 0006

To connect the wires: 1. Cut the cable at the good length. 2. Put a shrink sleeve at each end of cable. 3. Fit a wire terminal on each wire of the cable.

Figure 14: Fit the Wire Terminals 4. Pass the cable through the grommet in the AC Mains In protection cover. 5. Connect the wires to the connectors on the LPFC ( begin with the green/yellow wire). Do not fit back yet the cover, because you have to check the voltage first !

Figure 15: Connect the AC Cable to the Equipment 6. Connect the AC mains cable to the site power supply box.

54 / 84

3BK 17430 3135 RJZZA Ed.03


2.6.3.2 AC Power Supply Testing

AC 230V N

P

2

1

N

P

V

N

4

3

V

P

5

N

P

6

7

To test the power supply: 1. At site power cabinet: check if 230 V fuse breakers are switched OFF. 2. At rack side: using an ohmmeter, check that there is no short circuit between phase and neutral. 3. At rack side: do the same test between protective earth (green / yellow wire) and each 230 V wire. 4. At site power cabinet: switch ON the 230 V fuse breakers. 5. At rack side: check that the 230 V voltage between phase and neutral is present. 6. At rack side: using phase tester, check that the phase wire is connected at good connection point. 7. At site power cabinet: switch OFF the fuse breakers.

3BK 17430 3135 RJZZA Ed.03

55 / 84


2.6.4 Power Cables Connection for DC Variant 2.6.4.1 DC Power Supply Connection Nr

Material

1

Lug, hole

6 mm for 10 mm2 GND cable

Reference

Kit

1AB 032050022

Basic kit

To connect the DC power supply: 1. Prepare the head of the DC cable.

16mm

2. Put a shrink sleeve at the end of each cable.

3. Fit wire terminal at the end of each wire.

6

4. Run the -48 V DC power cable through the hole in the rubber protective cap, connect it to the DC In filter and attach it to the rack using cable ties.

56 / 84

3BK 17430 3135 RJZZA Ed.03


5. Connect the 0V DC cable to the M6 grounding bolt and attach it to the rack using cable ties.

BTS(x)

6. Connect and label the DC mains cable to the primary DC power supply.

3BK 17430 3135 RJZZA Ed.03

57 / 84


2.6.4.2 DC Power Supply Testing

DC − 48V

0V − 48V 2

1

V

3

0V − 48V

5

4

6

To test the DC power supply: 1. At side power cabinet, check if fuse breakers are switched OFF. 2. At rack side, using a multimeter, check if there is no short-circuit between -48V filter and 0V stud. 3. At side power cabinet, switch ON the fuse breakers. 4. At rack side, verify if the voltage between -48V filter and 0V stud is about -48 Volts DC nominal. Check carefully the polarity. 5. At site power cabinet, switch OFF the fuse breakers. 6. At rack side, using a multimeter, verify if the -48V is switched OFF. Fit the rubber cap to the -48V terminal.

58 / 84

3BK 17430 3135 RJZZA Ed.03


2.6.5 Fit the Mains In Cover To fit the cover: 1. Place the cover at the good position. 2. Fix the cover with the screws (See Figure 16 ). 3. Attach the cables to the cable way using cable ties and allow sufficient length of wires to avoid traction at terminals.

Figure 16: Fit the Mains In Cover

3BK 17430 3135 RJZZA Ed.03

59 / 84


2.7 PCM Cables Installation This chapter describes the procedure to: Install PCM cables in site cable tray Connect PCM cables to the rack.

2.7.1 Install the PCM Cables in the Cables Way Nr

Material

Reference

Kit

1

Label

3BK 08062 ADAA

Basic kit

2

Tie wraps

1AD 00414 0006

3

PCM cable L907/4 (120 ohm) 100 m roll

3BK 08965 AAAA

PCM cable L907/4 (120 ohm) 250 m roll or

3BK 08965 ABAA

FLEX 3/8 (75 ohm) 100 m roll

3BK 25241 AAAA

FLEX 3/8 (75 ohm) 250 m roll

3BK 25241 ABAA

Installation kit

1m

2

1

3

4

is

Ab

2

is 1

Ab

5

To install the cables in the cable way: 1. Install cables in PCM compartment of cable tray. 2. Attach cables with plastic tie wraps. 3. Mark cables with a marker. 4. Cut cables at good length. 5. Label cable with supplied labels.

60 / 84

3BK 17430 3135 RJZZA Ed.03


2.7.2 Cables Passing at Rack Side To pass the cables at rack side: 1. Strip the cable at cable gland level. 2. Pass the cables through the cable gland and attach them to the rack. 3. Tighten the gland on the cable.

15 mm

15 mm

1

3BK 17430 3135 RJZZA Ed.03

2

61 / 84


4. Identify the Abis connectors on OUTC board.

4

Abis (screwing)

Abis KRONE (inserting)

5

5. Pass the cables toward the OUTC board.

62 / 84

3BK 17430 3135 RJZZA Ed.03


2.7.3 Cables Connection at Rack Side During installation it is mandatory to use the right tool for each terminal block. The references for the insertion tools are: 1AD 03221 0001 for Krone 1AD 01604 0001 for Nexans.

2.7.3.1 Case of L907/ 4 - 120 Ohm Cable The following figure shows the L907/4 cable structure.

Quad 1 grey/white

purple/blue

grey/yellow

purple/white

Quad 4

Quad 2

grey/green

purple/brown

purple/red

grey/black

Quad 3 Figure 17: L907/4 Cable The following table gives the wires color, connecting position and signal. Color

KRONE connector

Signal

Quad 1

white

8

Abis1/TX

(output high level signal going toward BSC)

grey

8

Abis1/TX

blue

6

Abis2/TX

violet

6

Abis2/TX

3BK 17430 3135 RJZZA Ed.03

63 / 84


Color

KRONE connector

Signal

Quad 2

yellow

7

Abis1/RX

(input low level signal coming from BSC)

grey

7

Abis1/RX

brown

5

Abis2/RX

violet

5

Abis2/RX

Quad 3 & 4 not used Table 1: Wires Color, Position and Signals

150 mm

1

2

3

4

Sleeve

OUTC 8 1

1

TX

2

8

RX

3

TX

4

RX

5

RX

TX

6

RX

7

TX

1

8

8

1

5

6

To connect the L907/4 cable: 1. Remove the PCM lightening protection from KRONE connector of OUTC board 2. Prepare head of L907/4 cable 3. Fit a sleeve to end of cable 4. Insert the L 907/4 wires using mandatory KRONE original tool 5. Fit the lightening protection to the KRONE connector 6. Squeeze the cable braid in the metallic clamp.

64 / 84

3BK 17430 3135 RJZZA Ed.03


2.7.3.2 Case of FLEX3/8 - 75 Ohm Coaxial Cable The following table gives the wires connecting position and signal. Coaxial 1

KRONE connector Abis 1 (TX)

8 -braid 8 -inner conductor

2

Abis 1 (RX)

7 - braid 7 - inner conductor

3

Abis 2 (TX)


4

Abis 2 (RX)


50 mm

1234 10 mm

1 1

2

RX TX RX

4

1

3

TX

ABIS3

8

1

ABIS4

8

1

5

6

1. Remove the PCM lightening protection from KRONE connector of OUTC board

3BK 17430 3135 RJZZA Ed.03

65 / 84


2. Using Hot Air Blower, fit the Heat Shrink Sleeve 1AC 00330 0002 on each coaxial. Fit a rubber sleeve on head of cable 3. Insert the 75-ohm coaxial using original KRONE tool 4. Connect wire bridge for used ports on OUTC ABIS green connectors as follows: Wire bridge from pin 1 to pin 2 Wire bridge from pin 4 to pin 5 Wire bridge from pin 6 to pin 7 Ports assignment is 1 and 2 for GSM (3 and 4 are not used). 5. Fit the lightening protection to the KRONE connector. 6. Fit two SP2M 75-ohm adapter at PCM sub-D port ABIS1 and ABIS2 on OUTC board. The following figure shows an example of 75-ohm cabling.

8 coaxial cable

4

RX

5

TX

6

RX

7

RX

7

3

TX

TX

TX

8

RX

8

TX

TX coax.

2

TX

1

RX

Core

Figure 18: FLEX 3/8 Connection

66 / 84

3BK 17430 3135 RJZZA Ed.03


2.7.4 Other Connection Possibilities

RX RX 1 TX

ABIS1

8

1 TX

ABIS2

8

2.7.4.1 Connection of Other 120 Ohm Cables

Figure 19: Example of OUTC Screwing Connectors If cables are not supplied by Alcatel-Lucent, then the wires must have right specifications for inserting in the KRONE connector. If not, the wires have to be connected to the green screwing connectors of OUTC board ( Figure 19 ). The 3 jumpers must be removed from the connectors (they are used only for 75-Ohm connection).

3BK 17430 3135 RJZZA Ed.03

1

GND braid earthing clamp

2

TX

3

TX

4

GND drain wires

5

RX

6

RX

7

R200 (not used)

8

GND braid earthing clamp

BTS output signal going toward BSC

BTS input signal coming from BSC

67 / 84


2.7.4.2 Connection of Other 75 Ohm Coaxial Cables

123 123 123 123

10 mm 7

12345123 1234 123 121 1123456 12 12345 1234567 12345 123 123412345 123 123 121 121234567 11234567 1234 12345678 123456 123451 6

5

4

3

50 mm

2

1

123 123 2

1

To connect the cables: 1. Prepare the head of cables 2. Connect the wires to the terminals and mount the earthing clamp. Coaxial

Connector

Pin

Remarks

1

Abis 1 (TX)

2 - braid

For each connector :

3 - inner conductor

- wire bridge from pin 1 to pin 2

2

Abis 1 (RX)


3

Abis 2 (TX)

- wire bridge from pin 4 to pin 5 - wire bridge from pin 6 to pin 7


4

Abis 2 (RX)


68 / 84

3BK 17430 3135 RJZZA Ed.03


2.7.4.3 Connection of Optical Fiber PCM cable The section applies only for the optical transmission on Abis. The following table lists the items required to complete the task.

*

Description

Reference

Kit

Cable Optical fiber LC-LC 2SM 15m *

849122239

-

Cable Optical fiber LC-LC 2MM 5m *

849125513

-

SFP transceiver *

1AB 18728 0029

-

: Refer to Installation Kits (Section 1.4.1.2) for more optical fiber cables and SFP variants

To connect the PCM optical fiber cables: 1. Run the optical fiber cables through the cable gland/cable entry inside the cabinet. 2. Insert a SFP transceiver module in the OPT1 slot (on the GNC daughter board of the SUMX) and lock it. 3. Remove the protection cover from the SFP transceiver module. 4. Remove the protection caps from the optical fiber connectors. 5. Connect the cables to the OPT1 connector on SUMX. 6. Label the optical fiber cable on the SUMX side. 7. Tighten the cable gland, if applicable. The PCM optical fiber cables are installed.

3BK 17430 3135 RJZZA Ed.03

69 / 84


2.8 Antenna Jumpers Installation 2.8.1 Jumper Installation Nr

Material

Reference

Kit

1

Labels

3BK 08062 ADAA

Basic kit

2

Tie wraps

1AD 00414 0006

3

Antenna jumper cable

3BK 05360 xAAA

Installation kit

For the jumpers type 1AB 18821 0001 (3m) or 1AB 18821 0002 (4m), use the bending tool and follow the instructions from IO 95 (3DF 00300 0095 UAZZA). 45

NORTH

Ant A Ant B

Ant B Ant A

230 A

B A

B Label: ANT B AZIMUTH 125

Label: SECT: N ANT A

B

A

A

A

B

A B

B

N

P

ANB

ANB

CBO

Figure 20: Example of Antenna Cabling and Labeling

Figure 21: Label the Antenna Jumpers (Do Not forget the Frequency Labels)

70 / 84

3BK 17430 3135 RJZZA Ed.03


2.8.2 Connection to the Rack The antenna connections mapping is done according to the following scheme:

Sector N Ant B Sector N Ant A Sector P Ant B Sector P Ant A

Figure 22: Antenna Mapping To connect the cables: 1. Ensure that the radius of each cable is at least 3 cm. 2. Refer to Site-Specific Information (Section 1.2.2) for cables connections 3. Connect the cables to the rack (See Figure 23 ). 4. Tighten the screw manually then shake cables a little. 5. Using the tightening tool, tighten with firmness. 6. Use tie wraps to bundle the jumpers together.

Figure 23: Antenna Jumpers Connection

3BK 17430 3135 RJZZA Ed.03

71 / 84


2.8.3 Connection to the Feeders Check that feeders are properly connected to site ground ! If the feeders are not labeled, don’t connect the jumpers, but inform the customer and fulfill the CCL

Nr

Material

Reference

Kit

1

Vinyl electrical tape

1AC 01556 0001

Basic kit

2

Tie wraps

1AD 00414 0006

3

Rubber splicing tape

1AC 01595 0001

To connect the feeders: 1. Connect the antenna jumpers to the feeders 2. Verify the connectors 3. Screw connector male with connector female 4. Tighten the screw manually then shake cables a little

Figure 24: First Tighten Manually, then Use the Specific Tightening Tool 5. Using specific tightening tool tighten with firmness (“Tools catalogue”) 6. Fit the vinyl electrical tape (1) over the connectors. Start taping from 30 mm from the connector (jumper side) and go down stretching and overlapping (50%) 30 mm over the connector (1 layer). You should not see any metal after taping.

7. Fit the rubber splicing tape (3) of Figure 25 over the vinyl electrical tape. Start taping from 20 mm top of the connector (coaxial cable side) and go down stretching and overlapping (50%) 20 mm over the connector (1 layer).

72 / 84

3BK 17430 3135 RJZZA Ed.03


8. Fit the vinyl electrical tape (1) over the rubber splicing tape. Start taping from 30 mm from the connector (jumper side) and go down stretching and overlapping (50%) 30 mm over the connector (1 layer). At the end of taping do not stretch the tape in the last few turns.

9. Secure with tie wraps to avoid tape removing (2) of Figure 25 .

Vinyl Tie wrap electrical (2) tape (1) Feeder

Rubber splicing tape (3)

Tie wrap (2) Jumper

123 12345 12 1 1 12 23 123 12 12 12345 123456 1234567 1 12345 234 1212 12 1 1234 123 23 123 12345 1 12345 234 12 12 1 1212 123 1234 12345 12 1 123 1 234 1234 123 12 23 123 123 12 123 12 123 123 12345 1234 12 123 1234 12 12 1234 1234 123 123 12 123 1234 12 123 123 12 1234 12 1 1234 1234 123 12 234 12 123 12 1 12 1 12 123 23 123 123 123 12 123 123 1234 12 123 1234 123 12 12 1 123 123456 121234 123 12 1 1 234 2 123 12 123 12 123 1234 123 12 12345 123456 1212 12 12123 123 12345 1 23412 11 12 23 12 123 23 Ground link for feeders

Figure 25: Water Proof the Connections

3BK 17430 3135 RJZZA Ed.03

73 / 84


2.9 Options Installation 2.9.1 Alarm Cables Installation 2.9.1.1 Alarm Cables Passing Nr

Material

Reference

Kit

1

Tie wraps

1AD 00414 0006

Basic kit

2

Labels

3BK 08062 ADAA

Basic kit

3

L907/4 in 100 m roll

3BK 08965 AAAA

Installation kit

L907/4 in 250 m roll

3BK 08965 ABAA

Alarm

Figure 26: Alarm Cable Passing Through the OUTC Board

74 / 84

3BK 17430 3135 RJZZA Ed.03


1

2

1m rm 1

Ala

4 3

15 mm

15 mm

6 5

To pass the cables: 1. Mark the cables with a marker 2. Install the cables in the special compartment of the cable tray 3. Attach the cables with plastic tie wraps 4. Label the cables with supplied labels 5. Strip the cables at cable gland level 6. Pass the cables trough the cable glands Use adhesive tie wraps to fix the cable to the side wall.

3BK 17430 3135 RJZZA Ed.03

75 / 84


2.9.1.2 Alarm Cables Connecting To install the alarm cables: 1. Prepare the end of cable (cut the no-used wires)

70 mm

5

6

2. Label the cable with supplied labels: [Alarm 1]

3. Unscrew and remove the jumpers from X900 external alarm connector on OUTC

76 / 84

3BK 17430 3135 RJZZA Ed.03


4. Connect the cable to the X900 connector

5. Fix the cable in the earthing clamp.

3BK 17430 3135 RJZZA Ed.03

77 / 84


2.9.2 Synchronization Cables Installation 2.9.2.1 Synchronization Cables Passing Nr

Materials

Reference

Kit

1

Labels

3BK 08062 ADAA

Basic kit

2

Tie wrap

1AD 00414 0006

Basic kit

3

Cable for clock synchronization

-

Installation kit

Alcatel-Lucent 9100 BTS/G2-BTS (10 m)

3BK 08303 AA

Alcatel-Lucent 9100 BTS/Alcatel-Lucent 9100 BTS (10 m)

3BK 08304 AA

XCLK

Figure 27: Synchronization Cable Passing Through the OUTC Board

78 / 84

3BK 17430 3135 RJZZA Ed.03


2.9.2.2 Compact BTS Indoor/Outdoor Evolution / Alcatel-Lucent G2 BTS Connection

CLK in STSE via COB2

CBOE

OUTC XCLC 1 out

Master G2

G2

Slave CBOE OUTC XCLC 1 in

CLK out MBSR via COB2 Master

Slave 10 m

P2

P1 1

2 3 4 5

6 7 8 9

OUTC

COB2

screen screen white

5 9

5 9

brown green

4

4

yellow

8

8

grey

3

3

pink

7

7

blue

2

2

red

6 P1

6 P2

OCC23

3BK 08303 AA

Figure 28: Compact BTS Indoor/Outdoor / Alcatel-Lucent G2 BTS Synchronization Cable

3BK 17430 3135 RJZZA Ed.03

79 / 84


2.9.2.3 Compact BTS Indoor/Outdoor Evolution / MBS GSM Outdoor or 9100 BTS Evolution or 9100 BTS Connection

G3/G4/ COAR/ MBO/ OUTC CBOE XCLK 1 in

CBOE OUTC XCLC 1 out

Slave

Master 10 m

P2

P1 1

2 3 4 5

6 7 8 9

OUTC 1

COAR/OUTC 2 screen screen white

5 9

5 9

brown green

4

4

yellow

8

8

grey

3

3

pink

7

7

blue

2

2

red

6 P1

6 P2

OCC33

3BK 08304 AA

Figure 29: Compact BTS Indoor/Outdoor Evolution/ 9100 BTS Synchronization Cable To install the synchronization cables: 1. Choose the good configuration 2. Pass the synchronization cables in the site cable way 3. Label the cables with supplied labels 4. Dismantle SubD 9 connectors (write down the wire colors) 5. Pass the cables through the BTS bottom plate 6. Put back the SubD 9 connectors 7. Connect the cables to the corresponding sockets of connection area 8. Fasten the connectors with knurled screws.

80 / 84

3BK 17430 3135 RJZZA Ed.03


2.10 Finish Installation 2.10.1 Label the Rack BTS STATION

BTS STATION

4

4

Figure 30: Fit the "BTS STATION" and "N" Labels at the Top of the BTS

2.10.2 Close the Cable Entry

Cover Plate for Cable Entry

Figure 31: Close the Cable Entry To close the cable entry: 1. Fit the cover plate 2. Fix the plate to the rack with the provided screws (A).

3BK 17430 3135 RJZZA Ed.03

81 / 84


2.10.3 Leave the Site

1

2 1. Clean the site. Do not put packages into the customer bin. 2. Give the key to the site responsible.

82 / 84

3BK 17430 3135 RJZZA Ed.03

8

1

Figure 32: OUTC Connectors

2.11 OUTC Layout

3BK 17430 3135 RJZZA Ed.03

1

16

83 / 84


8 1 8 1 8 1 8 1

16 1


BLANK PAGE BREAK

84 / 84

3BK 17430 3135 RJZZA Ed.03

9100 Compact BTS EVO Installation

Recommend Documents