What does A/F stand for? A. Across Flat (Your Answer) B. Across Field C. Across Flange D. Across Fillet
Correct Q.2)
Name the type of manufacturing process indicated in the figure. A. Pyramid Knurling B. Diamond Knurling (Your Answer) C. Cross Knurling D. Straight Knurling
Correct Q.3)
What does this symbol indicate? A. Cylindricity (Your Answer) B. Straightness C. Parallelism D. Flatness
Correct Q.4)
How many principal views does an object have? A. 2 B. 4 C. 6 (Your Answer) D. 8
Correct
Q.5)
How many classes of fit are provided for keys? A. 1 B. 2 C. 3 (Your Answer) D. 4
Correct Q.6)
What type of fit does 6H/6g represent in screw threads? A. Medium (Your Answer) B. Tight C. Close D. Free
Correct Q.7)
What type of fit does 5H/4h represent in screw threads? A. Medium B. Tight C. Close (Your Answer) D. Free
Correct Q.8)
What type of fit does 7H/8g represent in screw threads? A. Medium B. Tight C. Close D. Free (Your Answer)
Correct Q.9)
Indicate the type of sectional view shown by the drawing:
A. Offset section (Your Answer) B. Aligned section C. Full section D. Half section
Correct Q.10)
Indicate the type of sectional view shown by the drawing: A. Offset section B. Irregular section C. Broken-out/Part section (Your Answer) D. Removed section
Correct Q.11)
Indicate the type of dimension shown in the parenthesis: A. Overall dimension B. Auxiliary dimension (Your Answer) C. Projection dimension D. Redundant dimension
Correct Q.12)
Choose the letter that indicates a dimension line A. a
B. b (Your Answer) C. c D. d
Correct Q.13)
Indicate the type of projection shown below: A. Auxiliary angle projection B. First angle projection C. Second angle projection D. Third angle projection (Your Answer)
Correct Q.14)
A. Pitch Value B. Circumference C. Counterbore (Your Answer) D. Countersunk
Correct
Q.15)
What does 25 in M8x25 above mean? A. Pitch value B. Tolerance C. Diameter D. Thread length (Your Answer)
Correct Q.16) Bisecting an angle is to: A. divide the angle into 2 equal parts (Your Answer) B. divide the angle into any 2 parts C. divide the angle into 10 degree intervals D. divide the angle into 1 degree intervals
Correct Q.17) Continuous thin lines are used for: A. fictitious outlines and edges (Your Answer) B. hidden outlines and edges C. visible outlines and edges D. cutting planes
Correct Q.18) 2:1 on a drawing means: A. half size B. full size C. double full size (Your Answer) D. two sizes
Correct Q.19) To construct a pentagon, which of the following drawing instruments is not used? A. Compass B. French curve (Your Answer) C. Ruler D. Pencil
Correct Q.20) When creating a multiview drawing of a design, which view must be first selected and oriented correctly as the first important step? A. Plan view B. Isometric view C. Front view (Your Answer) D. Side view
Correct Q.21) What does the 'M' in M16x1.5-6H mean? A. Measured thread B. Man-made thread C. Metric thread (Your Answer) D. Material thread
Correct Q.22) In the dimensioning of screw threads what does the abbreviation LH stand for? A. Least Height B. Long Handle thread C. Left Headed thread D. Left Hand thread (Your Answer)
Correct Q.23) What is the type of fit shown in the diagram? A. Shaft basis fit B. Hole basis fit (Your Answer) C. Clearance basis fit D. Inference basis fit
Correct Q.24) Indicate the method of tolerancing shown below: A. Permitted tolerance B. Unilateral tolerance C. Bilateral tolerance (Your Answer) D. Cumulative tolerance
Correct Q.25) What is the limit tolerance (hole basis) shown in the figure below?
A. Dia 50.000 - Dia 50.025 B. Dia 49.975 - Dia 49.991 (Your Answer) C. Dia 49.984 - Dia 50.000 D. Dia 49.858 - Dia 49.920
Correct Q.26) Which of the following indicates the cutting plane lines? A. A (Your Answer) B. B C. C D. D
Correct Q.27) Which of the following involving complicated hidden details is incorrect?
A. A B. B (Your Answer) C. C D. D
Correct Q.28) In a sectional view the following are not cross-hatched except: A. shaft B. rib C. pulley (Your Answer) D. nut
Correct Q.29) What does the abbreviation PCD stand for? A. Per circle dimension B. Pitch countersunk diameter
C. Possible circle diameter D. Pitch circle diameter (Your Answer)
Correct Q.30) Which of the following abbreviation of general engineering terms is incorrect? A. A/C: Across corner B. DRG: Drawing C. CSK: Countersunk D. CBE: Counterbore (Your Answer)
Correct Q.31) Name the type of coupling that will produce a non-uniform angular velocity at the output shaft when a uniform angular velocity is applied at the input shaft: A. Oldham coupling B. Flange coupling C. Spring coupling D. Hookes coupling (Your Answer)
Correct Q.32) What are the 2 main types of locking devices? A. Slipping & Positive B. Frictional & Negative C. Frictional & Positive (Your Answer) D. Slipping & Negative
Correct Q.33)
Name the type of coupling shown: A. Flange coupling (Your Answer) B. Bolted coupling C. Hookes coupling D. Oldham coupling
Correct
Q.34)
The correct illustration for the symbol shown is: A. A (Your Answer) B. B C. C D. D
Correct Q.35)
Choose the correct symbol for: A. A (Your Answer) B. B C. C D. D
Correct
Q.36)
A. Pitch value B. Circumference C. Counterbore (Your Answer) D. Countersunk
Correct Q.37)
What does 1.75 refer to? A. Pitch value (Your Answer) B. Circumference C. Diameter D. Thread length
