Manual C4 C5

distributed by www.minilablaser.com

INSTALLATION MANUAL < Optional Software >

FRONTIER SERIES DI PRINT/DATA WRITING SERVICE SOFTWARE Ver.5.5

DI Print/Data Writing Service Software Ver.5.5 (FRONTIER 330/340 System Disk Ver.2.0 or later) (FRONTIER 355/375 System Disk Ver.1.5 or later) (FRONTIER 350/370/390 System Disk Ver.6.6 or later)

Second Edition PP3-A1001E2

[email protected]

distributed by www.minilablaser.com INTRODUCTION

INTRODUCTION • This installation manual explains the procedures for installing and setting up the DI Print and Data Writing Service for Fujifilm Digital Minilab FRONTIER Series as well as precautions for its use. • This manual should be kept in a fixed place near the machine so that it can be referred to at any time a point needs to be clarified.

Specifications are subject to change without notification. Zip™ is a trademark of Iomega Corporation. SmartMedia™ is a trademark of Toshiba Corporation. CompactFlash™ is a trademark of SanDisk Corporation. Microdrive™ is a trademark of IBM Corporation. Memory Stick™ and Memory Stick Duo™ are trademarks of Sony Corporation. SD Memory Card™ is a trademark of Toshiba Corporation, Matsushita Electric Industrial Co., Ltd and SanDisk Coporation. miniSD Memory Card™ is a trademark of SD Card Association. Microsoft®, Windows® and Windows® 2000 are registered trademarks of Microsoft Corporation. All other brand names or trademarks are the property of their respective owners.

[email protected]


CONTENTS 1

Precautions for Installation .............................................................................................. 1.1

2

Hardware/System Configuration .................................................................................... 2.1

2.2

3

Hardware Configuration...................................................................................................... 2.1.1 FRONTIER 355/375 System .................................................................................. 2.1.2 FRONTIER 330/340 System .................................................................................. 2.1.3 FRONTIER 350/370/390 System ........................................................................... 2.1.4 Imaging Controller System (Example).................................................................... System Preparations .......................................................................................................... 2.2.1 PC and Media Drive Preparations.......................................................................... 2.2.2 Hard Disk Partition ................................................................................................. 2.2.3 Virtual Memory Setting ........................................................................................... 2.2.4 Computer Name Setting......................................................................................... 2.2.5 Network Protocol Setting........................................................................................ 2.2.6 Creating a User Account ........................................................................................ 2.2.7 Restarting ...............................................................................................................

6 6 6 7 8 9 10 10 11 11 13 15 17 20

Installation ............................................................................................................................... 22 3.1 3.2

3.3

3.4

3.5

4

Version of System/Option Software Combination ..............................................................

5 5

Standard Setup/Upgrade.................................................................................................... Custom Setup/Upgrade ...................................................................................................... 3.2.1 Custom Setup/Upgrade for Use of DI Print/Data Writing Service [C4/C5] ............. 3.2.2 Custom Setup/Upgrade for Use of DI Print Service [C4] Only ............................... MSDE/64MB SmartMedia Driver Installation...................................................................... 3.3.1 MSDE Installation................................................................................................... 3.3.2 64MB SmartMedia Driver Installation..................................................................... Backup Order Function....................................................................................................... 3.4.1 Added Functions .................................................................................................... 3.4.2 Installation .............................................................................................................. Installation to FRONTIER ................................................................................................... 3.5.1 [C4/C5] Installation ................................................................................................. 3.5.2 Installation Information Setup................................................................................. 3.5.3 Print Size Setup......................................................................................................

23 25 25 27 30 30 31 32 32 33 35 35 36 38

Setting the Imaging Controller ........................................................................................ 39 4.1

4.2

Print Service Administration ............................................................................................... 4.1.1 Setting for Media Drives and Executable Files....................................................... 4.1.2 Output Device Setting ............................................................................................ 4.1.3 Master Balance Adjustment ................................................................................... 4.1.4 Monitor Adjustment ................................................................................................ 4.1.5 DSC Setup ............................................................................................................. Data Writing Administration ................................................................................................ 4.2.1 Data Writing Statistic Log ....................................................................................... 4.2.2 Media Drive Setting ................................................................................................

[email protected]

39 41 42 43 44 45 46 48 50

3


4.3

4.4 4.5

4.6

5

6

5.1

Test DSC Printing...............................................................................................................

64

5.2 5.3

Test CD Writing .................................................................................................................. Test Print-to-Print Operation...............................................................................................

66 69

Product Information............................................................................................................. 71

6.2

4

51 52 54 55 55 56 58 59 59 60 62

Operation Test ....................................................................................................................... 64

6.1

7

4.2.3 Optional Software Setting....................................................................................... 4.2.4 Service Type Setting .............................................................................................. 4.2.5 Index Print Size Selection ...................................................................................... Print-to-Print Service Administration................................................................................... 4.3.1 Registering of Print-to-Print Service ....................................................................... 4.3.2 Print-to-Print Service Settings ................................................................................ Registering of Other Applications ....................................................................................... Digital Photo Center Administration.................................................................................... 4.5.1 Registering of Digital Photo Center Service ........................................................... 4.5.2 Digital Photo Center Settings ................................................................................. Multiple Service Setting ......................................................................................................

DI Print Product Information ............................................................................................... 6.1.1 Save to FD ............................................................................................................. 6.1.2 Log Contents .......................................................................................................... Data Writing Product Information ....................................................................................... 6.2.1 Save to FD ............................................................................................................. 6.2.2 Log Contents ..........................................................................................................

71 71 72 73 73 74

Index........................................................................................................................................... 75

[email protected]


1

Precautions for Installation

1.1

Version of System/Option Software Combination

1. FRONTIER 330 System Software and Optional Software K :Available A1

A2

B1

B3

B3/B4

B9

C2

C4/C5

C8

C10

✕ :N/A C11

Ver.1.0 Ver.3.0 Ver.4.0 Ver.4.1 Ver.1.0 Ver.1.5 Ver.1.7 Ver.4.5 Ver.4.6 Ver.5.0 Ver.5.5 Ver.1.1 Ver.1.0 Ver.1.0 Ver.1.0 Ver.1.5

K

✕

✕

K

K ✕

K

Ver.2.0

✕

✕

K

K

✕ K

K

K

✕

✕

K

K

✕ K

✕

✕

K

K

2. FRONTIER 340 System Software and Optional Software K :Available A1

A2

B1

Ver.1.0 Ver.1.0

Ver.4.0

K

Ver.2.0

Ver.4.5

B3/B4

B9

C2

Ver.2.0

Ver.1.5

Ver.1.7

Ver.4.5

Ver.4.6

K

K

K

K

✕

✕

✕

✕

K

K

✕

C4/C5 Ver.5.0

Ver.5.5

✕

✕

K

K

✕ :N/A

C8

C10

C11

Ver.1.1

Ver.1.0

Ver.1.0

K

K

✕ K

3.FRONTIER 350/370/390 System Software and Optional Software K :Available A1

A2

B1

B3

B5

B6

B7

B8

Ver.4.0

Ver.5.0

Ver.2.0

Ver.1.0

Ver.1.0

Ver.1.0

Ver.1.0

Ver.1.0

Ver.1.5

Ver.1.0

K

K

K

K

K

K

K

K (Note1)

✕

K

✕

✕

K

✕

K

K

C2 Ver.1.6

Ver.1.7

C4/C5 Ver.4.1

Ver.4.5

Ver.4.6

K

K

K

Ver.6.0 Ver.6.6

B11

Ver.3.0

Ver.7.0 A1

✕ :N/A

Ver.4.0 Ver.6.0 Ver.6.6

B9

K K (Note2) (Note3)

Ver.5.0

Ver.5.5

✕

✕

K

C8

C10

C11

Ver.1.1

Ver.1.0

Ver.1.0

K

K

K

✕ K

Ver.7.0

Note1: Not available for FRONTIER 390 Note2: Operated only on Windows NT Note3: Operated only with C4/C5 Ver.4.5 or later

A1: FRONTIER System B1: Variety Print B5: Single Scan Digitizing Function B8: Hyper Reorder B9: Tone Selection B11: Hyper Retouch B12: FRONTIER Automatization Support Software

C2: DI I/O Service C4/C5: DI Print/Data Writing Service C8: LAN Spool C10: Variety Print Digital C11: Hyper Retouch Digital

[email protected]

5


2

Hardware/System Configuration

2.1

Hardware Configuration

2.1.1 FRONTIER 355/375 System

LP1500SC/LP2000SC

SP3000

Imaging Controller (Example)

I/O Box

HUB

Imaging Controller

PC Card Reader

Monitor

Zip Drive

MO Drive

Mouse

CD-R Drive

Keyboard

Flatbed Scanner

(

USB or SCSI connection for use with Windows 2000

) FD162B

6

[email protected]


2.1.2 FRONTIER 330/340 System

SLP-800SC/SLP-1000SE


I/O Box

HUB

Imaging Controller

PC Card Reader

Monitor

Zip Drive

MO Drive

Mouse

CD-R Drive

Keyboard

Flatbed Scanner

(


) FD162BC

[email protected]

7


2.1.3 FRONTIER 350/370/390 System

LP1500SC/LP2000SC/LP2500P

SP1500/SP2000/SP2500


I/O Box

HUB

Imaging Controller

PC Card Reader

Monitor

Zip Drive

MO Drive

Mouse

CD-R Drive Keyboard

Flatbed Scanner

(


) FD162A

8

[email protected]


2.1.4

Imaging Controller System (Example)

Imaging Controller

Flatbed Scanner

Monitor

PC Card Reader

Mouse Keyboard

Zip Drive

MO Drive

CD-R Writer

CD-R Writer

I/O Box FD163

Memory StickTM, SD Memory Card TM and MicrodriveTM can also be used as media when using Windows ® 2000 system.

[email protected]

9


2.2

System Preparations

2.2.1 PC and Media Drive Preparations

Required SCSI board: • Adaptec 2940 • Adaptec 2930LP • Adaptec 29160

Prepare the PC, media drives, HUB, and the cables.

1

Required CD-R: • Fujifilm CD-R

PC that meets the following requirements: CPU : Pentium II 400MHz Hard disk : At least 9GB x 2 drives Memory : At least 256MB

2

OS Windows NT4.0 Workstation SP6 or Windows 2000 Professional SP2 SCSI board must be installed beforehand.

3

Required scanner type: • MICROTEK ScanMaker 4 • EPSON Expression 1600 • EPSON Expression 1680

Media drives and cables Zip, Jaz, MO, CD-R, PC card, SSFDC, CF, Flatbed scanner, etc. (SD Memory Card, Memory Stick and Microdrive are supported only with Windows 2000) In Windows 2000, the USB connection is also available for the drive media except CD-R. However, the processing speed in USB connection is not assured, and correct assignment of drive name may not be done. Required CD-R drive types: • YAMAHA CRW 400tx • YAMAHA CRW 4260tx • YAMAHA CRW 4416sx • YAMAHA CRW 6416sx • YAMAHA CRW 8424sx • YAMAHA CRW 8824sx • YAMAHA CRW 2100s-Vk • PLEXTOR CD-R/W PX-W8220Te • PLEXTOR CD-R/W PX-W124TSe • PLEXTOR CD-R/W PX-W1210TS • PLEXTOR CD-R/RW PX-W4012TS (For the above CD-R drives, SCSI connection is used with both Windows NT4.0 and Windows 2000)

IMPORTANT: Never use the CD-RW media instead of CD-R.

4 5

HUB and two network cables to connect Frontier to HUB and HUB to Imaging Controller. CRT Monitor

• Color Temperature: 6500° K • Resolution: 800 x 600 pixels or higher • Display Color: 32bit

6

“Aspi” manager must be installed. If not, an error may occur when starting “Data Writing” or “Print to Print” software. At the installation of the Windows NT, “Wnaspi32.DLL” is installed in the “System32” folder in the “Winnt” folder in the C drive, but it is not activated. To activate it, install and set up “Wnaspi32.DLL” using any of the following ways. (1) Install “EZ-SCSI(CD-ROM)” provided with “Adaptec 2940” SCSI board. (2) Install the writing software “EZ-CD creator” provided with the dedicated CD-R drives. (See “Recommended CD-R drive types” shown above.)

Make sure to use the SCSI connection for the CD-R drive.

10

[email protected]


2.2.2 Hard Disk Partition

2.2.3 Virtual Memory Setting

During the installation of Windows NT/Windows 2000, partition your hard disk into two regions: one for the system and the other for order registration and spooling (Ex: 4GB for the system and 5GB for order registration). For details see the Windows NT/ Windows 2000 setup manual.

[In case of Windows NT]

1 2

On the Desktop, choose [Start] - [Settings] [Control Panel]. Click the [System] icon in the “Control Panel” window. • The “System Properties” screen appears. Select [Performance] tab.

Click.

3

Click [Change] under [Virtual Memory] on [Performance] tab. • The “Virtual Memory” screen appears. Click.

Click.

[email protected]

11


4 5

4

In the Drive list, click the drive you want to change.

Click [Change]. • The “Virtual Memory” screen appears.

Under “Paging File Size for Selected Drive”, type “500” in the Initial Size (MB) and Maximum Size (MB) boxes.

Select the drive.

Click.

If the “Paging File Size” is less than 500MB, make it more than 500MB. If it exceeds 500MB, make sure to allocate it more than the physical memory size.

6 7

Click [Set]. Click [OK]. • Operation returns to the “System Properties” screen.

8

On the “System Properties” screen, click [OK]. • Operation returns to the “Control Panel” window. Check if the initial size (MB) and maximum size (MB) are more than 500MB.

[In case of Windows 2000]

1 2

5

On the Desktop, choose [Start] - [Settings] [Control Panel].

6

Click the [System] icon in the “Control Panel” window.

In the Drive list, click the drive you want to change. Under “Paging File Size for Selected Drive”, make sure that the Initial Size (MB) and Maximum Size (MB) are more than 500MB. If the “Paging File Size” is less than 500MB, make it more than 500MB.

• The “System Properties” screen appears.

3

Click.

Click [Performance Options] on [Advanced] tab. • The “Performance Options” screen appears.

7 8

Click [Set]. Click [OK]. • Operation returns to the “Performance Options”, so click [OK] to return to the “System Properties” screen.

9

On the “System Properties” screen, click [OK]. • Operation returns to the “Control Panel” window.

Click.

12

[email protected]


5

2.2.4 Computer Name Setting

In the [Computer Name] box, type “FRONTEND” and click [OK].

[In case of Windows NT] • The confirmation message appears.

1 2

On the Desktop, choose [Start] - [Settings] [Control Panel]. Click [Network] in the “Control Panel” window. • The “Network” screen is displayed.

Click.

Select [Identification] tab.

6

Click [OK]. • Operation returns to the “Network” screen.

3 4

Click.

Click [Identification] tab. Move the cursor to the Computer Name and click [Change]. • The “Identification Changes” screen appears. Type “FRONTEND”.

[email protected]

13


5

[In case of WIndows 2000]

1 2

On the Desktop, choose [Start] - [Settings] [Control Panel].

In the [Computer Name] box, type “FRONTEND” and click [OK]. • The confirmation message appears.

Click [System] in the “Control Panel” window. The “System Properties” screen is displayed. Select [Network Identification] tab.

Click.

6

Click [OK]. • Operation returns to the “System Properties” screen.

Click.

3 4

Click [Network Identification] tab. Click [Properties]. • The “Identification Changes” screen appears. Type “FRONTEND”.

14

[email protected]


4

2.2.5 Network Protocol Setting

If “NetBEUI Protocol” is not found in the “Network Protocols:”, register it.

[In case of Windows NT] (1) Click [Add].

IMPORTANT: Make sure to use NetBEUI protocol.

1

(2) Select “NetBEUI Protocol” and then click [OK].

On the “Network” screen, click [Protocols] tab. Select [Protocols] tab.

Select [NetBEUI Protocol].

Click.

(3) Complete the registration by following the messages given.


2

Click “NetBEUI Protocol” in the Network Protocols and click [Close]. • The “Network Settings Change” message appears.

IMPORTANT: Make sure to use NetBEUI protocol.

1

On the “Control Panel” screen, double-click [Network and Dial-up Connections].

Click.

3

Click [No].

Double-click.

[email protected]

15


2 3

Click [Local Area Connection] icon and then click [Network Identification] tab.

6

If “NetBEUI Protocol” is not found in the “Components checked are used by this connection:”, register it.

Double-click “Local Area Connection” icon. (1) Click [Install]. • The “Local Area Connection Status” screen appears.

(2) Click [Protocol], and then click the [Add] button. Select [Protocol].

Click.

Click.

4 5

(3) Select [NetBEUI Protocol] and then click [OK].

Click [Properties].

Confirm if “NetBEUI Protocol” in the “Components checked are used by this connection:” is checked [√], and if not, check [√] it.

Select [NetBEUI Protocol].

Check if [NetBEUI Protocol] is checked [√].

Click.

If [NetBEUI Protocol] is not found, click [Install].

16

[email protected]


3

2.2.6 Creating a User Account [In case of Windows NT]

1

Type “FRONTIER” in both the [User name] and [Full Name] columns, and enter a password in both the [Password] and [Confirm Password] columns.

On the Desktop, choose [Start] - [Programs] [Administrative Tools] - [User Manager].

Type “FRONTIER”.

• The “User Manager” screen appears.

2

Click.

In the User menu, click “New User”.

• Check “Password Never Expires” box.

4

Click [Groups]. • The “Group Memberships” screen appears.

• The “New User” screen appears.

5 6 7

Choose “Administrators” and click [Add]. On the “Group Memberships” screen, click [OK]. On the “New User” screen, click [OK].

[email protected]

17


4


1

Select [Tree]-[Users].

On the “Control Panel” screen, double-click [Users and Passwords].

Select [Tree]-[Users].

5

Select [New User···] from [Action] on the menu bar.

Double-click.

2

Click [Advanced] tab. Click [Advanced] tab.

6

Type “FRONTIER” in [User name], [Full name], [Password] and [Confirm password:] columns. Type [FRONTIER].

3

Click [Create] then [Close].

Click [Advanced].

Remove the checkmark from “User must change password at next log-on”, and check [√] “Password never expires”. Click.

18

7

Click [Create] and then click [Close].

[email protected]


8

Select [FRONTIER] from the right-hand list (1), and then select [Properties] from [Action] on the menu bar (2).

10

Select [Administrators] on the “Select Groups” screen, and then click [Add] to add it to the list. And then click [OK].

Select [FRONTIER] (1).

Select [Administrators].

Select [Properties] (2).

9

Click.

Click [Member Of] tab, and then click [Add···] Select [Member Of] tab.

11

Click if “Administrators” exists in the list on [Member Of] tab of the [FRONTIER Properties] screen. Click if “Administrators” exists.

Click.

Click [Apply] then [OK].

12

Click [Apply] and then click [OK].

[email protected]

19


2.2.7 Restarting

1

[In case of Windows NT]

On the Desktop, choose [Start] - [Shut Down].

• “(Build 1381: Service Pack 6)” is displayed in the upper right-hand corner of the Windows NT’s BLUE starting screen. [Windows 2000] Microsoft® Windows NTTM Version 4.0 (Build 1381: Service Pack 6). 2 System Processors [256 MB Memory] MultiProcessor Kernel

2

• The settings take effect after restarting the computer.

In case of Windows NT, click “Restart the computer?” and click [Yes]. [Windows NT]

In case of Windows 2000, select “Restart” and click [OK]. [Windows 2000]

20

[email protected]


[In case of Windows 2000] • Check if the Service Pack is properly installed using the following procedures.

1

On the “Control Panel” window, click [System] icon.

Click.

• The “System Properties” screen appears.

2

Check that the Service Pack 2 is displayed in the “System” on the “General” tab.

[email protected]

21


3

Installation

DI Print Service/Data Writing Software Ver.5.5 can only be operated in the following combination of the system or other optional software.

FRONTIER 350/370 FRONTIER 390 FRONTIER 330/340 FRONTIER 355/375

A1: System Software Ver.7.0 or later A1: System Software Ver.7.0 or later A1: System Software Ver.2.0 or later A1: System Software Ver.1.5 or later

IMPORTANT: Printing (including negative printing) cannot be performed during the installation. IMPORTANT: Before starting the installation, perform the post-operational check, and shut down the FRONTIER. Do not shut it down by using the emergency stop button. IMPORTANT: Before updating the “DI Print/Data Writing Service Software [C4/C5]” from Ver.4.5, Ver.4.6 and Ver.5.0 to Ver.5.5, make sure that there are no orders in the DI Print [C4] and Data Writing [C5] services, then close the [C4/C5]. When orders remain in the [C4/C5], complete the printing and writing first, then start updating. If you start updating while the orders remain in [C4/C5], they will be deleted.

(FRONTIER 330 Ver.2.0 or earlier/350/370/390)

(FRONTIER 330/340 Ver.3.0 or later)

(FRONTIER 355/375)

22

[email protected]


3.1

Standard Setup/Upgrade

For the upgrade, use the same procedures as for the Standard Setup. Before starting the installation of the DI Print/Data Writing Service Software [C4/C5], perform the Post-operational check in FRONTIER and shut it down. To install the DI Print/Data Writing Service Software [C4/C5] Ver.5.5, the Ver.5.0 software must be installed in the Imaging Controller.

1

Click the [Exit] button while pressing the [Shift] key to close the DI Print/Data Writing Service [C4/C5].

3

Select [Run] from [Start] menu on the Desktop.

Click [Exit] while pressing [Shift] key.

4 2

On the “Run” screen, enter “h:\setup.exe”, then click [OK].

Insert the DI Print and Data Writing Service Software CD into the CD-ROM drive.

The drive name (ex:h:\) varies according to the CD-ROM drive into which you inserted the installer CD.

FD201

5

On the “Setup Type Selection” screen, select [Standard Setup], then click the [Next] button. Select [Standard Setup].

[email protected]

23


6

On the “Start Copying Files” screen, click the [Next] button.

Click.

• Installing starts.

7

Upon completion of installation, remove the CD from the CD drive, and then restart the Imaging Controller.

FD202

24

[email protected]


3.2 3.2.1

Custom Setup/Upgrade

Custom Setup/Upgrade for Use of DI Print/Data Writing Service [C4/C5]

3


For the upgrade, use the same procedures as for the custom setup. Before starting the installation of the DI Print/Data Writing Service Software [C4/C5], perform the Postoperational check in FRONTIER and shut it down. To install the DI Print/Data Writing Service Software [C4/C5] Ver.5.5, the Ver.5.0 software must be installed in the Imaging Controller.

1

Click the [Exit] button while pressing the [Shift] key to close the DI Print/Data Writing Service [C4/C5].

4

Click [Exit] while pressing [Shift] key.



2


5

On the “Setup Type Selection” screen, select [Custom Setup], then click the [Next] button.

FD201

[email protected]

Select [Custom Setup].

25


6

On the “Select Application” screen, click the [DI Print/Data Writing Service Software Ver.5.5] button.

If you added a hard disk drive for temporary directories, enter its drive name.

9

On the “Enter Text” screen, check if the “FRONTEND” is selected, and then click the [Next] button.

Click.

NOTE: If “MSDE” and “64MB SmartMedia Driver” are not installed in your system, install them. (See “3.3 MSDE/64MB SmartMedia Driver Installation” on page 30.)

7

On the “Setup Type Selection” screen, select [DI Print/Writing Service]. Then, click the [Next] button.

Click.

10

On the “Spool Drive Setting” screen, select any drive name (ex.“D”) as spool drive, and then click the [Next] button.

Select a Setup type.

8

Click.

On the “Working Drive Setting” screen, click the [Next] button.

Click.

26

[email protected]

The spool drives can be divided into two regions: One for “Inspool” and another for “Outspool”. Registered or digitized images are stored in the “Outspool”. If you have added a hard disk drive with a large storage space to the system, change the drive name to the newly added drive for storing large-size images.


11


3.2.2 Custom Setup/Upgrade for Use of DI Print Service [C4] Only For the upgrade, use the same procedures as for the custom setup.

1

Click the [Exit] button while pressing the [Shift] key to close the DI Print/Data Writing Service [C4/C5]. Click [Exit] while pressing [Shift] key.

Click.


12


2


FD201 FD202

3


[email protected]

27


4


7

On the “Setup Type Selection” screen, select [DI Print Service Only]. Then, click the [Next] button.


5

Select a [DI Print Service Only].

On the “Setup Type Selection” screen, select [Custom Setup], then click the [Next] button.

8

On the “Enter Text” screen, click the [Next] button.

Select [Custom Setup].

6

On the “Select Application” screen, click the [DI Print/Data Writing Service Software Ver.5.5] button.

Click.

9


Click.

NOTE: If “MSDE” and “64MB SmartMedia Driver” are not installed in your system, install them. (See “3.3 MSDE/64MB SmartMedia Driver Installation” on page 30.)

28

[email protected]

Click.



10


FD202

[email protected]

29


3.3

MSDE/64MB SmartMedia Driver Installation

If your Imaging Controller already has the MSDE/64MB SmartMedia Driver Installed, skip this section.

3

3.3.1 MSDE Installation

1

In the “Restart” dialog box, click the [Yes] button.

On the “Setup Type Selection” screen, select [Custom Setup], then click the [Next] button. Select [Custom Setup]. Click.

2

On the “Select Application” screen, click the [MSDE] button. Click.

• MSDE is installed.

30

[email protected]


3.3.2

1

64MB SmartMedia Driver Installation

4

On the “Welcome” screen, click the [Next] button.

On the “Setup Type Selection” screen, select [Custom Setup], then click the [Next] button. Select [Custom Setup].

Click.

• The driver is installed right away.

2

On the “Select Application” screen, click the [64MB SmartMedia Driver] button.

5

On the “Setup Complete” screen, click the [Finish] button.

Click.

3

In the “Confirmation” dialog box, click the [Yes] button.

Click.

Click.

[email protected]

31


3.4

Backup Order Function

Backup Order Function is the function where you can temporarily store the orders from the external application (Kiosk, etc.), and later can correct them on the View and Order screen.

3.4.1 Added Functions

NOTE: If the Backup Order Function is installed, processing may be slower because the back-up processing from the registered devices is done each time it is executed.

By installing the Backup Order Function, the following functions can be used.

[Printing(C4)] • Re-registration function of printing order • Test printing on the View and Order screen

[Writing(C5)] • New services (devices) are added. The following devices are added to the Digital Service Selection list. Service Name FDi CD1 FDi CD2 FDi CD3

NOTE: This function cannot be uninstalled. NOTE: To disable this function, edit (comment-out) the device for backup order function that is defined in the “C:\FE\FEIN\InUkBackup.ini” file.

Functions Three types of FDi CD are added. Additional data such viewer can be written.

FDi CD with FCD

FUJICOLOR CD with FDi CD (higher- or lower pixels)

Pro CD

In this service the order uses the print size selected in the Print Size setup in film scanning, while the original image size is adopted in the DCS Printing.

• Picture Rotation The radio buttons for selecting the upper side are added to the frames on the Image List screen. To display these radio buttons, add the checkmark [√] to [Yes] box on [Picture Rotate] on the Writing Service - Administration screen.

32

[email protected]


3.4.2 Installation

• Installation (DOS) screen appears, and it disappears when installing is completed.

Install the Backup Order Function. Installation is done by running the two batch files.

1

Click the [Exit] button while pressing the [Shift] key to close the DI Print/Data Writing Service [C4/C5]. Click [Exit] while pressing [Shift] key.

4

On the “Run” screen, enter “H:\Merlin\MerlinPatch2.bat”, then click [OK]. Enter “H:\MerlinPatch2.bat”.

2

On the Desktop screen, select [Run] from [Start] menu.

Click.

The drive name (ex:H:\) varies depending on your system.

5

On the confirmation (Registry Editor) screen, click [Yes].

Select [Start] - [Run].

3

On the “Run” screen, enter “H:\Merlin\MerlinPatch1.bat”, then click [OK].

Click.

6

Enter “H:\MerlinPatch1.bat”.

On the confirmation (Registry Editor) screen, click [Yes].

Click. Click.

The drive name (ex:H:\) varies depending on your system.

[email protected]

33


• After the restart, the [Backup Order] button and [Main List/Backup List] tab appear on the Printing screen. [Backup Order] button

[Main List/Backup List] tab

34

[email protected]


3.5

Installation to FRONTIER

2

3.5.1 [C4/C5] Installation

On the “Enter Text” screen, click the [Next] button.

Install the [C4/C5] in the FRONTIER. For the upgrade, use the same procedures as for the standard setup.

1

Insert the DI Print/Data Writing Service Software [C4/C5] installing or upgrading CD into the CD drive, and then restart the FRONTIER after performing the Post-operational Check. [FRONTIER 330/340/355/375] Click.

3


[FRONTIER 350/370/390]

Click.


4

Upon completion of installation, restart the FRONTIER.

[email protected]

35


3

3.5.2 Installation Information Setup Set the external file I/O to ON to communicate with the Imaging Controller.

Select [41 System Operation Setup and Check] [41F Installation Information Setup] and click [START].

■ FRONTIER 350/370/390

1

On the “Main Menu” screen, select [Setup and Maintenance] and click [OK].

Click.

4

2

Click [Option].

In the “Log-in” dialog box, select [Laboratory Manager], then enter the password “0000” and click [OK]. Select “Laboratory Manager”.

Click.

5

On the “Optional Device Setting” screen, set [External File I/O] to [YES], then click [OK]. Click [YES].

Click.

Click.

36

[email protected]


6 7

On the “[41F] Installation Information Setup” screen, click [OK].

3

Select [01 System Operation Setup and Check] [0140 Installation Information Setup].

In the confirmation dialog box, click the [OK] button.

Click.

4

■ FRONTIER 330/340/355/375

1

On the “Installation Information Setup” screen, click the [Option] button.

On the “Main Menu” screen, click the [Setup and Maintenance] button. Click.

Click.

5 The above is an example of a FRONTIER 340 screen.

2

On the “Optional Device Setting” screen, set [External File I/O] to [YES] and then click the [OK] button. Set [External File I/O] to [YES].

Enter the password “7777”, and then click the [OK] button. Enter “7777”.

Click.

6 Click.

In the confirmation dialog box, click the [OK] button.

[email protected]

37


■ FRONTIER 330/340/355/375

3.5.3 Print Size Setup On the FRONTIER, set the print sizes to be used in DIGITAL IMAGING PRINT SERVICE.

2 3

example.

1

■ FRONTIRER 350/370/390

1

The following procedures use the FRONTIER 355 as

Perform Steps 1and 2 in “3.5.2 Installation Information Setup” (page 36) to open the “Setup and Maintenance” screen.

2

Select [Print Condition Setup and Check] - [Print Size Setup (424)] to open the “Print Size Setup” screen.

Perform Steps 1 and 2 in “3.5.2 Installation Information Setup” (page 36) to open the “Setup and Maintenance” screen. Select [02 Print Condition Setup and Check] [0220 Print Size Setup] to open the “Print Size Setup” screen. Select [02 Print Condition Setup and Check] - [0220 Print Size Setup].

Set the print size.

3

Set the print size.

IMPORTANT: When registering the print size, never use a size designation with more than five characters. If used, an error will occur when the connection is established with the Imaging Controller at the pre-operational check.

4 5

Click the [OK] button. Repeat Steps 3 and 4 for each print size.

IMPORTANT: When registering the print size, never use a size designation with more than five characters. If used, an error will occur when the connection is established with the Imaging Controller at the pre-operational check.

4 5 38

Click the [OK] button. Repeat Steps 3 and 4 for each print size.

[email protected]


4

Setting the Imaging Controller

4.1

Print Service Administration

Perform the print service administration settings on the Print Service Administration screen. Here, you can perform or change the settings such as the output device, media drive, etc.

1

2

On the “Printing” screen, click the [Admin.] button.

In the “Password” dialog box, enter “DI”, and then click the [OK] button.

Click.

Enter “DI”.

Click.

6

5

9

1

10 11 12 13 14 15 16 17

2

3

4 18

7 No.

8

Item

19 Description

1

Index Print

Select [Yes] to print the DSC index print.

2

Minimum Image Size

Set the printable minimum image size, normally 20KB to avoid the registration of too small images as such as thumbnails. If trying to register the images with less than the set size, the following message appears on the Order Registration screen.

[email protected]

39


No.

40

Item

Description

3

Automatic Transaction for all Frames

When [Auto.] button is turned ON, select a type of the automatic transactions on the “Printing” screen. • to “Select All and Set”: Automatic processing to the stage to “Select All and Set”. Click [Order Regist.] to complete an order. • to “Order Registration”: Automatic processing to the stage to “Order Registration”. The registration is completed simply by selecting media. • to “View All Image”: Automatic processing to the stage to “View and Order”. After the media selection, you can monitor and adjust the images on the “View and Order” screen.

4

Back Print

Select if the Back Printing is to be done or not. Add a checkmark [√] to select it.

5

Default Print Q’ty

Sets the default number of prints, index print and large index print sheets to be output.

6

Key Step

Set the CMYD key steps used on the “View and Order” screen (Recommended values: CMY: 3, DcDmDy: 5).

7

Machine ID

Identifies the multiple Imaging Controllers with this ID (a character of an alphabet except “N” and “R”). This ID is added to the head of the order number.

8

Auto Correct - Disable

If this is checked [√], the auto correction is not applied to the image.

9

Help

Displays the help screen.

10

Version Info.

Displays the version information about this Software.

11

Statistic Log

Stores the statistic information for each registered image data file into the FD, and monitor them.

12

Monitor Adjust

Displays the “Monitor Adjust” screen and matches the color balance of the monitor to the print on the “View and Order” screen.

13

Master Balance

Set the color master balance for printing for each print service. Normally set “0”.

14

Media Drive

Set the media drives and relate them to the appropriate media icon.

15

Output Device

Select the device name of the printer or other devices to be used.

16

Multiple Service

Displays the “Multiple Services - Administration” screen.

17

DSC Setting

Displays the “DSC Setup Setting” screen, where you can adjust the color, tone and sharpness settings.

18

[OK] button

Makes the settings effective. Control returns to the Printing screen.

19

[Cancel] button

Cancels the settings. Control returns to the Printing screen.

[email protected]


4.1.1 Setting for Media Drives and Executable Files On the Print Service Administration screen, click [Media Drive] to open the Media Drive Setting screen, on which you set the media drives and relate them to the appropriate media icon.

2

3

4

5

1

6

7

No.

Item

Description

1

Drives1 to18

The selected drive icons appear on the Printing screen.

2

Icon Display

Displays the icons to be used.

3

Name

Shows the drive name or software name.

4

Drive

Select the drive letter and relate it to the icon.

5

File Path

Specify the full path to the application. Path and drive cannot be specified simultaneously.

6

[OK] button

Makes the settings effective. Control returns to the Print Service - Administration screen.

7

[Cancel] button

Cancels the settings. Control returns to the Print Service - Administration screen.

When using the external executable files such as PtoP and Digital Photo Center, set the icon and file path as shown below. Icon

File Path

PtoP

C:\FE\scanner\scanapp.exe

Digital Photo Center (LAN connections) DPC1 to DPC9

C:\FE\kiosk\kiosk.exe

Digital Photo Center (OFF line) DPC-Media

C:\FE\kiosk\kiosk.exe X Add “X” (drive name for DPC-Media). A space must be used to separate File Path from drive name for DPCMedia.

[email protected]

41


4.1.2 Output Device Setting On the Print Service Administration screen, click [Output Device] to open the Output Device Setting screen, on which you relate the output device to the icons. IMPORTANT: These settings can be done only if the pre-operational check is completed on the FRONTIER 330/350/370/ 390. 2

3

4

5

1

Default print size cannot be set in the “Multiple” service.

6 7

No.

Item

Description

1

Output Devices1 to 8

The icons of the output devices appear on the Printing screen in this order.

2

Icon Selection

Select the desired output device icon by clicking it.

3

Icon Name

Specify the device name under the icon using up to 8 characters. To use the Hyper-Retouch Service [C11], install it beforehand.

4

Device

This information is registered to the system at the time of “Pre-operational check” in FRONTIER.

FRONTIER 330

SP-800sRGB or SP-800PD

340


350/370

42

Device Name

SP-1500/2000sRGB or SP-1500/2000PD

390


355/375


[email protected]


No.

Item

Description

5

[Print Size] button

Displays the “Print Size Setting” screen. These buttons set the default values of DSC/Media, DPOF Print, Index print and Large Index. Press [Print Size] button to set the desired print size for each print service. This value will be displayed on the “Printing” screen. Once the size is specified as default, this value will be displayed. In the “Multiple” service, the default print size cannot be selected.

6

[OK] button

Makes the settings effective. Control returns to the Print Service screen.

7

[Cancel] button

Cancels the settings. Control returns to the Printing screen.

4.1.3 Master Balance Adjustment

2

On the Print Service Administration screen, click [Master Balance] to open the Master Balance screen, on which you set the color balance for printing for each print service.

3

Click [OK] button to make the settings effective. Control returns to the Print Service Administration screen. Click [Cancel] button to cancel the settings. Control returns to the Printing screen.

The settings done on this screen are only applied to the print, not to the CD-R writing.

1

Set the master balance with the value from -99% to +99% for each service Digital Still Camera Print, CD-R Reprint or Media Print.

[email protected]

43


4.1.4 Monitor Adjustment

5

On the Print Service Administration screen, click [Monitor Adjust] to open the Monitor Adjust screen, on which you match the color balance of the monitor to the print.

6

[Auto Correction]

7 8 9

When the sample print is output, open the Monitor Adjust screen again. And then adjust the CMY while checking the color on the print. And then click [Apply] to apply the adjusted values to the monitor. Repeat Step 5 several times, and then click [OK] to register the values. Control returns to the Printing - Administration screen. Click [OK] button to make the settings effective. Control returns to the Print Service Administration screen. Click [Cancel] button to cancel the settings. Control returns to the Printing screen.

[No Correction]

1 2 3 4

Select [Auto Corr.] tab or [No Corr.] tab. On the Monitor Adjust screen, click [Sample Print] to register the sample print order. After the disappearance of the sandglass icon, click [Cancel] to return to the Print Service Administration screen. And then click [Cancel] to return to the Printing screen. Print the order ZA9998 (No Correction) or ZA9999 (Auto Correction) on FRONTIER. • “CX MX YX” is printed on the back of the sample print.

44

[email protected]


4.1.5 DSC Setup On the “DSC Setup Setting” screen, you can set and change the initial parameters for color, tone and sharpness adjustment for DSC printing. On the “Print Service - Administration” screen, click [DSC Setting].

3

5 1

2

6 7 4

No.

Item

Description

1

Color Intensity

Set up the chroma saturation value from -2 to +4.

2

Gradation Adjustment

Select the type of Pro DI Gamma from “Hard2” to “Soft3”.

3

Hyper Tone

Select the mode of the Hyper Tone.

4

Sharpness

Select “Noise Reduction” or “Standard (USM)” for sharpness type.

5

[Help] button

Displays the Help screen.

6

[OK] button

Makes the settings effective. Control returns to the “Print Service - Administration” screen.

7

[Cancel] button

Cancels the settings. Control returns to the “Print Service - Administration” screen.

[email protected]

45


4.2

1

Data Writing Administration

2

On the “Writing” screen, click the [Admin.] button.


Click.

Enter “DI”.

Click.

4

3 11

1 2 12 13 14 15

5

6 7 8

16

9

17

10

18

19

No.

Item

Description

1

Adapter No. and SCSI ID

Select an appropriate combination of SCSI HOST Adapter number and SCSI ID for the CD-R drive.

2

CD-R Drive Name

Select the drive name for the CD-R drive.

3

CD-ROM Drive Name

Select the drive name for the CD-ROM drive.

46

[email protected]


No.

Item

Description

4

Verify Type Selection

• Verify after writing (new CD-R): Check the box to verify the CD-R after writing in a new CD writing. Normally remove the checkmark [√]. • Verify after writing (additional data): Check the box to verify the CD-R after writing in an additional writing. Normally checkmark [√].

5

Media Drive

Displays the drive set for writing on the Media Drive Setting screen.

6

Media Drive Setting

Displays the Media Drive Setting screen.

7

Optional Software Setting

Displays the application software set on the Optional Software Setting screen. [Setting] button: Displays the Application Software Call Setup screen.

8

CD-R Index Setting

Set the device for printing the CD-R index and large-index prints, and their print size, and then set “Yes” or “No” to print them. [Device]: Select the device for printing the CD-R index or large-index prints. For large index print, normally select “A4 (210x297mm)” or “8R (203x254mm. 254x203mm)”

9

Print Size

Click [Select] to display the Print Size Selection screen.

10

Index/Large Index

Sets the default value for “Yes” or “No” to Index/Large Index on Image List screen.

11

[Help] button


12

Version Info.

Displays the version information.

13

Statistic Log

Display the Statistic Log screen.

14

Service Type Setting

Displays the Service Type Setting screen.

15

Multiple Service

Displays the Multiple Service screen. (See “4.6 Multiple Service Setting” on page 62.)

16

Writing Speed

Select [Fast] or [Normal] for data writing speed. [Fast] : maximum capability of device [Normal] : octuple speed

17

Data Delete Interval

Set up the time (min) for the data to be deleted after completing processing. Range : 0-999

18

[OK] button

Stores the settings and exits this screen.

19

[Cancel] button

Exits this screen without storing the settings.

[email protected]

47


4.2.1 Data Writing Statistic Log On the Writing Service Administration screen, click [Statistic Log] to open the Log screen, on which you display and store the statistic log. (For details of product information, see “6 Product Information”.)

3

4

5

1 2

6

7

No.

48

Item

8

Description

1

Period

Displays the period during which the statistic log is accumulated.

2

Writing Total

Displays the total copies of writing during the period.

3

Service

Displays the writing service type.

4

Copies

Displays the number of copies.

5

Images

Displays the number of images.

6

[Help] button


7

[Save] button

Saves the statistic log to FD. As the log has the “CSV” format, it can be monitored by using the spreadsheet software.

8

[Return] button

Exits this screen.

[email protected]


1

2

3

No.

Item

Description

1

Starting date

Specify the starting date to log.

2

Saving days

Specify the number of days to be saved.

3

Path to save

Shows the drive/path where the log file will be output.

In the above dialog box, click [Yes] to remove the Writing log. Note that the Writing log can be removed only in this dialog box, not on the “Product Information” screen. Note that the removed log is never restored.

[email protected]

49


4.2.2 Media Drive Setting Select the name, icon and output path and relate them for each media drive other than the CD-R media. The following three writing services are registered as default. CD-R 4base JPG FUJICOLOR CD(4base,JPG) Free Export BMP Set the media type on this screen, and then make Service Type Settings on the Service Type Setting screen. (See “4.2.4 Service Type Setting” on page 52.) On the Writing Service Administration screen, click [Media Drive Setting] to open the Media Drive Setting screen.

1

2

3

5

4

6

No.

50

Item

7

Description

1

Icon

Select icons for displaying on the Main screen.

2

Drive

Set the drive letter for the writing drive.

3

Output Path

Enter the directory name with the full path for writing to HD or network drive.

4

[Brows...] button

Displays the Browse screen for selecting the directory. The selected directory appears in the Output Path box.

5

[Help] button


6

[OK] button


7

[Cancel] button


[email protected]


4.2.3 Optional Software Setting On the Writing Service Administration screen, click [Setting] in the Optional Software Setting field to open the Optional Software Setting screen, on which you can set the FUJIFILM optional software (up to three different packages). For example, when using the Digital Photo Center, use the pull-down menu to select “Digital Reorder”, and then specify “C:\FE\DR\DigitalReorder.exe” as Path for the Optional Software.

2

3

4

1

6

5

No.

Item

Description

1

Icon

Select the icon for the software.

2

Path for the Optional Software

Enter the full path name to locate the selected software.

3

[Help] button


4

[Brows...] button

Displays the file selection screen for selecting the file. The selected file appears in the Path for the Optional Software Output Path. Select only the file with “exe” extension.

5

[OK] button


6

[Cancel] button


[email protected]

51


4.2.4 Service Type Setting Use the “Service Type Setting” screen for setting the type of several writing service combination of Media Type, File Format and Image Size. On the Writing Service Administration screen, click [Service Type Setting] to open the Service Type Setting screen.

1

2

3

4

6

No.

52

Item

5

7

8

Description

1

Service Name

Displays the service name with the media type, file format and image size. The selected service name is displayed on the Output Device Selection screen when performing Digital Image Export on the FRONTIER.

2

Media Type

Displays the media type for the writing service. Supported media type: CD-R Free Export (same function as C2: BMP Export provides)

3

File Format

Displays the selected image file format. Supported file format: JPG (Exif-JPG), FPX, BMP, FUJICOLORCD

4

Image Size (Base)

Displays the type of the image size. Supported image size: 1base, 4base, 16base, Free Size

5

[Help] button


6

[Set] button

Register the service name with the media type, file format and image size, and add it to in the list.

7

[Delete] button

Deletes the selected service name.

8

[Return] button

Exits this screen.

[email protected]


Restrictions for Service Type Combination (1) When selecting “FREE EXPORT” as Media Type, only “Print Size” can be specified as Image Size. (2) When selecting “FUJICOLOR CD” as File Format, only “4base” as Image Size and “CD-R” as “Media Type” can be selected. (3) When selecting “FD” as Media Type, only “1base” can be selected as Image Size. The following table shows the relation between Media Type, File Format and Image Size.

Service Composition

Media Type

File Format

Image Size 1Base

4Base

16Base

Free Size

Available

Available

Available

Available

FUJICOLOR CD

N/A

Available

N/A

N/A

FDi CD

N/A

Available

N/A

N/A

CD Pro

N/A

N/A

N/A

Available

ZIP/JAZ/MO/ HD1 to 6

FPX JPG BMP

Available

Available

Available

N/A

FD

JPG

Only Film Scan

N/A

N/A

N/A

Free Export

JPG BMP

N/A

N/A

N/A

Available

FPX JPG BMP CD-R

[email protected]

53


4.2.5 Index Print Size Selection On the Writing Service Administration screen, click [Select] in the CD-R Index Setting field to open the Print Size Selection screen, on which you select the print size for the index print. This service is available only for film scanning.

1

No.

54

2

3

4

5

Item

6

Description

1

No.

Displays the serial number.

2

Name

Displays the print size name.

3

Width (mm)

Displays the paper width (mm).

4

Feed (mm)

Displays the paper feed (mm).

5

Width (pixel)

Displays the paper width (pixel).

6

Feed (pixel)

Displays the paper feed (pixel).

[email protected]


4.3

Print-to-Print Service Administration

Perform the Print-to-Print service settings on the Administration screen.

4.3.1

Registering of Print-to-Print Service

4

Set the icon and file path as shown below.

Set up the file path to the executable file for the Print-to-Print Service on the “Print Service Administration” screen.

1

Icon

File Path

PtoP

C:\FE\Scanner\scanapp.exe

On the “Printing” screen, click the [Admin.] button. Click.

Select the icon file path.

5 2

Click the [OK] button.

In the “Password” dialog box, enter “DI”, and then click the [OK] button. Enter “DI”.

Click.

3

Click.

On the “Print Service - Administration” screen, click the [Media Drive] button.

6

On the “Print Service - Administration” screen, click the [OK] button.

Click.

Click.

[email protected]

55


2

4.3.2 Print-to-Print Service Settings

On the “Print-to-Print” screen, click the [Admin.] button.

Set up the administrative items for Print-to-Print Service.

1

Click.

On the “Printing” screen, select the output device and then click the [PtoP] button. Select the output device.

Click.

3

Perform the administration work as shown below.

5

1

2 3 4

8 9

7

6 No.

56

Item

Description

1

Output Device

Select the output device from the Output Device pull-down menu.

2

Print Size

Select the default print size from the Print Size pull-down menu.

[email protected]


No.

Item

Description

3

TWAIN Source

Select the TWAIN source from the TWAIN Source pull-down menu. Enter any of the following TWAIN sources. Microtek Scanmaker 4: Microtek ScanWizard(32bit) EPSON Expression 1600/1680: EPSON TWAIN Pro(32bit)

4

Scanner Type

Select the scanner type from the Scanner Type pull-down menu.

5

Scanner Balance

Adjust the master color balance for this service after the fine scanning. (Value: -99 to +99)

6

Monitor Balance

Adjust the monitor color balance for this service after the fine scanning. (Value: -99 to+99)

7

Contrast

Adjust the contrast for the highlight or shadow part of the image after the fine scanning. (Value: -5 to +5)

8

[OK] button

Allows all settings to take effect then returns to the main screen

9

[Cancel] button

Cancels all settings then returns to the main screen.

5 and 6 can be set only after the fine scanning is completed.

[email protected]

57


4.4

Registering of Other Applications

Set up the file path to the executable file for other applications on “Writing Service - Administration” screen. This section explains how to set up the Digital Reorder service application.

1

On the “Writing” screen, click the [Admin.] button.

Set up the icon and file path.

Click.

2

4


On the “Writing Service - Administration” screen, click the [Setting] button in the [Optional Software Setting] field.

Click.

5 Click.

3

On the “Writing Service - Administration” screen, click the [OK] button.

On the “Optional Software Setting” screen, set up the icon and file path as shown below. Icon

File Path

Reorder

C:\FE\DR\DigitalReorder.exe

Click.

58

[email protected]


4.5

Digital Photo Center Administration

Digital Photo Center is an in-store order terminal that is connected to the Imaging Controller. When using it, perform the Digital Photo Center service settings on the Administration screen.

4.5.1 Registering of Digital Photo Center Service

4

Set the icon and file path as shown below. Icon

Set up the file path to the executable file for the Digital Photo Center Service on the “Print Service Administration” screen.

1

On the “Printing” screen, click the [Admin.] button.

File Path

DPC1 to DPC9 (LAN)

C:\FE\kiosk\kiosk.exe

DPC-Media (OFF-line)

C:\FE\kiosk\kiosk.exe X Add “X” (drive name for DPC-MEdia)

Click.

Set the icon and file path.

2


5


Enter “DI”.

Click.

3

On the “Print Service - Administration” screen, click the [Media Drive] button. Click. Click.

[email protected]

59


6

On the “Print Service - Administration” screen, click the [OK] button.

4.5.2 Digital Photo Center Settings Set up the administrative items for Digital Photo Center Service.

1

On the “Printing” screen, click the [DPC1] to [DPC9] or [DPC-M] button. Click [DPC1] to [DPC9] or [DPC-M].

Click.

2

On the “Digital Photo Center” screen, click the [Admin.] button. Click.

60

[email protected]


3

Perform the administration work as shown below.

1

No 1

Item Print Setting

Description Select the name of the device currently connected and the print size to be used. The information will be registered in the FRONTIER data base. Click the [Spool Setting] to display the following “Spool Setting” screen.

■ Spool Setting Screen

1

No 1

Item Spool Setting

Description Specify the name of the folder for the storing spool. The name must be specified by the full path name such as D:\DPCdata\. Normally enter the following values. Root Path: D:\DPCdata Frontier Print: pcpr DPC Print: aldn

[email protected]

61


4.6

Multiple Service Setting

The Multiple Service is a service that provides multiple order registration at a time of film scanning or image entry from the Digital Media. To use this service, register a combination of output devices beforehand. Use the following procedures to register it. On the “Print Service - Administration” screen or “Writing Service - Administration” screen, click [Multiple service] button. • The “Multiple Service - Administration” screen appears. 2 8 1

9 10 3 4 5 6

11 No

62

12

Item

13 Description

1

Multiple Service List

Lists up the names of the multiple services that were registered.

2

Multiple Service Composition

Shows the selected service contents.

3

Multiple Service Name

Enter the name of the service in this space.

4

Print Output Device

Select an output device. This information is registered to the system at the time of “Pre-operational check” in FRONTIER.

5

Image Writing Service

Select a writing service to be registered.

6

Image Use Service

Select it when using Digital Reorder or NET service.

7

Other

(Not used)

8

[Help] button


9

[1 Line Up] button

Moves the selected service upward in the Multiple Service List.

10

[1 Line Down] button

Moves the selected service downward in the Multiple Service List.

11

[Entry] button

Adds the selected service to Multiple Service List.

12

[Delete] button

Removes the selected service from Multiple Service List.

13

[Return] button

Returns to the Print Service - Administration screen.

[email protected]


■ Setting Procedures

1 2 3

Select the items to be serviced in the “Service Composition”. Enter the name of the multiple service in the “Multiple Service Name”. Click the [Entry] button. • The created service is added to the “Multiple Service List”.

4

Click the [Return] button. • Control returns to the “Print Service - Administration” screen or “Writing Service - Administration” screen.

[email protected]

63


5

Operation Test

Perform the test DSC printing, CD writing, and Print-to-Print operation.

5.1

1

Test DSC Printing

Set the media including the image(s) in the drive.

4

Click the [Set] button to list up the images in the “Order Specification Column”.

FD214

2

Select the printing device in the [OUTPUT] field, and then any of the media in the [INPUT] field.

Click.

Select the media.

5

Click the [Order Regist.] button.

Select the printing device.

3

Click.

Find the folder, and then select the image(s).

6

The “Confirmation” dialog box appears.

Select the image(s).

64

[email protected]


7

9

Remove the media from the drive.

Print the registered images with FRONTIER.

FD124

8

(FRONTIER 350/370/390)


Click.

(FRONTIER 330/340)

(FRONTIER 355/375)

[email protected]

65


5.2

1

Test CD Writing

Set the media including the image(s) in the drive.

4

Find the folder, and then select the image(s). Select the image(s).

FD214

2

Select the writing device in the [OUTPUT] field, and then any of the media in the [INPUT] field.

5

Select the writing device.

Click the [Set] button to list up the images in the “Order Specification Column”.

Select any of the media.

3

Click.

On the “Service Select” screen, click the [OK] button.

6

Click the [Order Regist.] button.

Click.

Click.

66

[email protected]


7

The “Confirmation” dialog box appears.

8

Remove the media from the drive.

11

Double-click the order in the [Order Registration] Status field.

Double-click.

12

On the Image List screen, check the image(s), and then click [OK] button.

FD124

9


Click.

10

Click the [Writing] icon to display the “Writing” screen.

13

Insert the CD-R into the drive.

Click the [Writing] icon.

C45019

[email protected]

67


14

Click [OK] button. In case of media writing, insert the specified media instead of CD-R.

Click.

15

Writing is started.

16


Click.

17

Remove the CD-R from the drive.

C45020

68

[email protected]


5.3

1

Test Print-to-Print Operation

4

Click [PtoP] in the [INPUT] field.

Click the [Add image to Order] button.

Click.

2

5

Set the photo on the scanning table glass.

FD191

3

6

Click the [Order Regist] button, then the [Return] button.

Remove the photo from the scanner and store it in a safe place.

Click the [Fine Scan] button.

FD192

[email protected]

69


7

Print the registered images with FRONTIER.

(FRONTIER 350/370/390)

(FRONTIER 330/340)

(FRONTIER 355/375)

70

[email protected]


6

Product Information

The product information log can be monitored on the “Log” screen called by clicking the [Statistic Log] button on the “Order Reception - Administration” screen. These log data stored in the “C:\FE” folder can also be copied into the FD and can be monitored and analyzed.

6.1

DI Print Product Information

3

6.1.1 Save to FD

1

Insert a formatted 1.44MB FD into the FD drive.

Click the [Statistic Log] button on the “Print Service - Administration” screen.

Make sure to use a new formatted FD. • Upon completion the copy, the message appears.

4


Click the [Statistic Log] button.

• The “Log” screen appears.

2

Click the [Save to FD] button.


[email protected]

71


6.1.2 Log Contents Monitor the statistic log information using some editor, or spread sheet software.

Example of Data Items: 1 2 3 4 5 6

Order NO. Reception date Order file version Order file creating date Driver Application name

7 8 9 10 11 12

Camera model (only EXIF) Flash No/Yes Format*1 Print Q'ty File name print size

*1 “Win” appears also for Mac processing because it is converted to Win format in the application software.

1

2

A00650 2004/9/ 420:53

3

4

5

6

V1.00

2004/9/4

F-DI Net Serner V2.00

7

8

9 Win

10

11

10 DPC001.FPX

12 POST CARD

A00656 2004/9/ 711:50

FUJIFILM FinePix500

YES Win

1 DSCF0013.JPG DSC

A00661 2004/9/ 711:57

FUJIFILM FinePix700

NO

Win

1 DSC00001.JPG DSC

A11664 2004/9/ 712:02

NIKON E900

NO

Win

1 DSC00001.JPG DSC

A00668 2004/9/ 712:07

FUJUFILM DS-30

NO

Win

1 DSC00001.JPG DSC

A00669 2004/9/ 712:07

RICOH DC-4 YES Win

A00674 2004/9/ 716:09

1 RIM0009.JPG

DSC

Win

1 SONYMVCFD7 .JPG

DSC

A00011 2004/9/ 716:16

V1.00

2004/6/30 phex-win-v1.50

PICTURE.EXE

Win

1 4.FPX

A5

A00030 2004/9/ 714:07

V1.00

2004/9/7

PD-WIN -V1.50

MAMEW9.EXE

Win

3 2.FPX

C

A00030 2004/9/ 814:07

V1.00

2004/9/7

PD-WIN -V1.50

PHOTOS01.DLL

Win

10 4.FPX

72

[email protected]

POST CARD


6.2

Data Writing Product Information

4

6.2.1 Save to FD

1

Insert a formatted 1.44MB FD into the FD drive. Make sure to use a new formatted FD.

Click the [Statistic Log] on the “Writing Service Administration” screen.

• Log file is copied FD.

Click the [Statistic Log] button.

• Upon completion the copy, the message appears. • The “Log” screen appears.

2

3

5

Click the [Yes] button.


On the “Save Statistic Log” screen, select [Starting date] and [Saving days], then click the [OK] button.

[email protected]

73


6.2.2 Log Contents Monitor the statistic log contents using some editor, or spread sheet software.

File Contents [CD-ID No.]. . . . . . . . . . . . . . . . . . . . . . . . . . [Order Number] . . . . . . . . . . . . . . . . . . . . . . [NEW / ADD] . . . . . . . . . . . . . . . . . . . . . . . . [Number of CD-R Index Prints] . . . . . . . . . . [Number of Images] . . . . . . . . . . . . . . . . . . . [Creating Date]. . . . . . . . . . . . . . . . . . . . . . . [Media Type]. . . . . . . . . . . . . . . . . . . . . . . . . [Version] . . . . . . . . . . . . . . . . . . . . . . . . . . . . [FRONTIER]. . . . . . . . . . . . . . . . . . . . . . . . .

12digits 6digits NEW / ADD 1digits 3digits year / month / day / hour / minute / second CD-R (fixed) 1.0 (fixed) FRONTIER TYPE

Sample Output

74

CD-ID

Order Number

NEW/ADD

Index

Number of Images

Creating Date

106717100378

900002

NEW

5

192 2004/1/1213:49

CD-R

1 SLP1000_Input

106717100368

900007

ADD

1

40 2004/1/1412:31

CD-R

1 SLP1000_Input

106717100382

900008

NEW

5

200 2004/2/1414:05

CD-R

1 SLP1000_Input

106717100384

1

ADD

4

160 2004/2/1615:37

CD-R

1 SLP1000_Input

106717100383

30

NEW

1

1 2004/2/2216:48

CD-R

1 SLP1000_Input

[email protected]

Media Type

Version

FRONTIER


7

Index

Numerics

M

64MB SmartMedia Driver Installation .....................31

Backup Order Function .............................................32 ———Added Functions ............................................32 ———Installation .......................................................33

Master Balance Adjustment ..................................... 43 Media Drive Setting ................................................... 50 Monitor Adjustment ................................................... 44 MSDE Installation ...................................................... 30 MSDE/64MB SmartMedia Driver Installation ........ 30 Multiple Service Setting ............................................ 62

C

N

[C4/C5] Installation ....................................................35 Computer Name Setting ...........................................13 Creating a User Account ..........................................17 Custom Setup/Upgrade ............................................25 Custom Setup/Upgrade for Use of DI Print Service [C4] Only .................................27 Custom Setup/Upgrade for Use of DI Print/Data Writing Service [C4/C5] .............25

Network Protocol Setting .......................................... 15

B

D Data Writing Administration .....................................46 Data Writing Product Information ............................73 Data Writing Statistic Log .........................................48 DI Print Product Information ....................................71 Digital Photo Center Administration........................59 Digital Photo Center Settings ..................................60 DSC Setup ..................................................................45

F FRONTIER 330/340 System ..................................... 7 FRONTIER 350/370/390 System.............................. 8 FRONTIER 355/375 System ..................................... 6

O Operation Test ........................................................... 64 Optional Software Setting ........................................ 51 Output Device Setting ............................................... 42

P PC and Media Drive Preparations .......................... 10 Precautions for Installation ......................................... 5 Print Service Administration ..................................... 39 Print Size Setup ......................................................... 38 Print-to-Print Service Administration ...................... 55 Print-to-Print Service Settings ................................. 56 Product Information ................................................... 71

R Registering of Digital Photo Center Service .......... 59 Registering of Other Applications ........................... 58 Registering of Print-to-Print Service ....................... 55 Restarting.................................................................... 20

S H Hard Disk Partition.....................................................11 Hardware Configuration.............................................. 6 Hardware/System Configuration ............................... 6

I Imaging Controller System (Example) ..................... 9 Index Print Size Selection ........................................54 Installation ...................................................................22 Installation Information Setup ..................................36 Installation to FRONTIER .........................................35

Save to FD ........................................................... 71, 73 Service Type Setting ................................................. 52 Setting for Media Drives and Executable Files ..... 41 Setting the Imaging Controller ................................. 39 Standard Setup/Upgrade.......................................... 23 System Preparations ................................................. 10

T Test CD Writing.......................................................... 66 Test DSC Printing ...................................................... 64 Test Print-to-Print Operation .................................... 69

L

V

Log Contents ....................................................... 72, 74

Version of System/Option Software Combination .... 5 Virtual Memory Setting ............................................. 11

[email protected]

75


[email protected]


FAX : 81-3-5484-0454

Questionnaire concerning This Manual Fujifilm’s Technical Division Photo Products Marketing would be most grateful if you would make copies of this form, then complete and send them to us by FAX. Your opinions will contribute greatly to an accurate assessment of the overall quality of each manual. All questions can be answered by ticking [✓] the appropriate box(es), but in addition to these answers, please provide us with your written comments in the lined spaces following each block of questions. Title : FRONTIER Series DI Print/Data Writing Service Software Ver.5.5 INSTALLLATION MANUAL

Manual Title and Reference Number

Reference Number : PP3-A1001E2

Name :

Your Name and Company

Company :

E-mail Address :

Your E-mail Address and FAX Number

Question 1

•

•

Question 2

•

FAX Number :

How would you rate this manual overall? (1) Very easy to use and understand

(2) Fairly easy to use and understand

(3) Slightly difficult to use and understand

(4) Very difficult to use and understand

Please provide us with your reasons and comments.

Have you found any technical errors, errors in spelling, or missing words in this manual? Yes

Question 3

No

•

If you have ticked (Yes), please let us know what these errors and missing words are.

•

How would you rate the writing (language, choice of words/phrases, etc.) and the illustrations/ diagrams, etc.? (1) Clear and easy to follow

(2) Should be simplified

(3) Difficult to follow (1)’ [Illustrations, etc.] Of adequate size (2)’ [Illustrations, etc.] Too small (3)’ [Illustrations, etc.] Difficult to follow •

If you have ticked (2), (3) or (3)’, please give us your reasons.

Additional Comments/ Requests concerning This Manual Please return this questionnaire to :

FAX No. : Tokyo 81-3-5484-0454 [email protected]


FUJI PHOTO FILM CO., LTD. 26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan. Printed on Recycled Paper Ref.No.PP3-A1001E2 TD-04.10-FG Printed in Japan

[email protected]

Manual C4 C5

Recommend Documents